Estimate for renovation of park near H.No 868 sec 45

Amount

-Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge. All kinds of soil (NEW HSR 2021 - 4.12.1)

-6.1.6 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1 :4: 8 ( 1 Cement : 4 coarse sand (zoneIll) : 8 graded cum stone aggregate 40 mm nominal size) 2735

-Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) (NEW HSR 7.21.1)

-Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 confonning to IS: 2222 in superstructure above plinth level up to floor four level in cement mortar 1 :6 (1 cement : 6 coarse sand) H.S.R. NO - 7.23.1 (With non-modular bricks)

-Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works (NEW HSR 13.29.2)

-24.10.4 cement concrete 1:2:4 with stone aggregate 20 mm nominal size in Kerbs and the like items, finished smooth with 6mm thick cement plaster 1:3 on exposed surface including from work, placing and fixing in position , complete at the ground level or in first storey 4874

-Brick ballast, well or over burnt broken and screened through a 32mm x 32mm square mesh screen laid consolidated and rammed to a finished thickness of 75mm as above.

-Washed stone grit plaster on exterior walls height up to 1 O metre above ground level, in two layers, under layer 12 mm cement plaster 1 :4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer@ 2 kg of cement per square metre, top layer 15 mm cement plaster 1 : 1 / 2:2 ( 1 cement: 112 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in-charge (payment for providing grooves shall be made separately). (NEW HSR 11.39)

-Providing and fixing pair of Plastic dustbins 100 litre volume each, of two different colours, for dry and wet waste, made of virgin plastic to be mounted on MS rectangular hollow section 50 x 25 x 3 mm frames pivoted on 3 MS square hollow section verticals, 1 m above ground, one 35 cm RHS welded to each vertical member at base and grouted in 180 x 40 x 30 cm 1 :2:4 cement concrete. NEW HSR NO - 26.76

-Arm and ShoulderWheel:- Providing, and fixing Arm and Shoulder Wheel of size 130 X '1200 X 1350 mm make of Green Gym or Equivalet fabricated with main post of 140 mm dia and 3.0 mm thic rest of the pipes are 40mm dia and 2.5 mm thick all pipc made up of hot roiled tubular steel and hot dippe galvanized, and powder coated using Akzo Nobel c equivalent of 80-120 micron thick. All welding joints of pip

-Double Cross Walker/ Cross trainer double:- Providing, and fixing Double Cross Walker of size 1600 X 600 X 1600 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40 mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer -in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength N425 and J shaped welded bolts and once the concrete is set, fix

-Horse Rider Station:- Providing, and fixing of horse rider station of size 1000 x 600 x 1100 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Alczo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and a. .royal of arge regari ing materia , s ape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc.

-Seated chest press: Providing designing and fixing of seated chest press in a pair of size 1800 x 700 x2000 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5 mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury. Seats and base plate cover to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 3mm colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete or minimum strength M-25 and J shape welded bolt and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per direction and approval of engineer in charge regarding material shape of equipment colour on metal seat and base plate and fixing of equipments etc (the cement concrete and excavation work shall be paid for separately).

-Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge 11.40.1 15 mm wide and 15 mm deep groove 11.40.2 20 mm wide and 15 mm deep groove

-6.1.2 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1:2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded cum stone aggregate 20 mm nominal size) New hsr 3892

-Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied@ 0.90 litre/10 sqm over an under coat of primer applied @ 0.80 litre/1 O sqm of approved brand and manufacture ( NEW HSR - 11.97.3)

-(i) 6 No. Ornamental Design FRP pillar FRP base pedestal with vertical fitted design having base width of size 260mm x 260mm and height 900mm having 4 no. of size 15mm drilled in the base with hold fasts and having B class vertical m.s pipe of size 89 mm and height 2890mm, the central m.s pipe having FRP capital suitably mounted at appropriate height complete as per design enclosed. Complete pillar suitably grinded spray primered and subsequently spray painted with two coats of enamel paints is required shade. (ii) 12 No. spndred and 6 no. Friezes Floral and Ornate decorative design combination of spandrel and frieze, matched to be suspended between two m.s pillars as per the design copy enclosed. The spandrel (L-Bracker) having length 310mm and height 300mm the frieze (Top Panel) height 220mm and length as per the size of the gazebo. The frieze mounted on m.s tabular pipe frame of size 40mm x 25mm, frieze properly welded to the column pollars at either ends. Complete set of spandrel & frieze uniformly grinded spray primered, spray painted with two coats of enamel paint. (iii) 3 No. cast iron base panel railing with frame Floral and Ornate decorative design cast iron side railing panel as per design copy enclosed having height of 730mm and length as per size of Gazebo. Each panel top and bottom mounted with mild steel tubular pipe frame of size 40 x 25 mm. the bottom mild steel pipe having 3 nos. of hold fasts in m.s pipe of size 40 x 40mm and length 50mm welded at the base to hold the panel in the ground. The complete railing panel grinded for neat surface finishes spray primered and subsequently spray painted with two coats of enamel paint in required shade. (iv) One set of top frame with frp roof Top frame in m.s tubular pipe of size 40 x 40mm properly welded and grinded. The top frame mounted with FRP molded Sheet of 2 mm thick bent to profile on either ends with clear width installation of frp sheets fixed horizontally along the length between column pillars. Each sheet enamel painted in red color on both sides. Each such sheet properly riveted to horizontal sheets. The roof pipe frames properly primered and painted in red color. The complete item is without C.C floor & without sitting bench. rates are including with all taxes.

-Chain Swing (2 seater): 10’L x 5’.5W x 8’.5 H. Horizontal frame & vertical legs is of m.s pipe 2” x 12 gauge. It stays with m.s pipe 1” x 12 gauge. Swinging seats-2 nos is of FRP molded Seat of 2mm thick fitted with m.s pipe ½” frame x 12 gauge which hang with m.s chain 6mm thick duly plated with ball bearing & m.s flat 6mm thick housing with suitable PU Primer & PU Paints.

-Merry-Go-Round (4 seater): 5' Dia. Main frame is of m.s sq. pipe 2" x 2" x 14 G and having suitable handle & foot-rest is of m.s round pipe 3/4" x 12 Gauge. Central pipe is of m.s pipe 3" x 12 G which further supports with m.s pipe 1” x 12Gauge with heavy duty shaft 50 mm thick & ball bearing assembly. It consists of 4 no Chair made of Molded FRP Plastic in 3mm thick with suitable PU Primer & PU Paints. Complete item with GST, Transportation, Installation with C.C & labor at site.

-Pull Chair:- Providing, and fixing of Pull pair of size 2500 X 800 X 2000 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 3.0 mm thick all pipes made up of hot roiled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc .primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be' made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GULLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of

-20MM dia Gunmetal gate valve with wheel (HSR -2021 B 1262) Rate - Rs.325 each

-HSR 2021 Item No 26.58.3 Cast Iron bench of 1800 mm length, 900 mm width, 450 mm seating height, sides made of cast iron. Seat and back shall be made of 10 strips of M.S. pipes 63 mm x 25 mm of 14 gauge with one M.S. Flat 25 x 10 mm welded at the centre, below and back of the seat and back rest. Spray painted with approved brand paint. Fixed by grouting with 1 :2:4 cement concrete (Minimum weight of each bench 105 kg). All materials required to be as per BIS specifications.

-Digging holes in all kinds of soil, and refilling the same, with the excavated earth, mixed with well decayed farmyard manure (cost of well decayed farm yard manure to be paid separately) Hole 0.60 metre dia and 0.60 metre deep ( NEW HSR NO - 26.13.4)

-HSR Good Earth for filling un-even land [HSR 3.1.2 + 17.8.2 + 17.8.3] 228

-17.5.3 Compaction of Earthwork Compaction of & preparation of sub grade including loosening, levelling of earth 225 mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering, rolling with road roller, compacting the bed to achieve minimum dry density as given in the Table 3000-2 as per technical clause 305 of MORT&H specifications (in case of link roads earthwork to be done by villagers) New hsr 16

-Providing and laying damp-proof course with cement concrete 1 :2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 12.5mm nominal size) H.S.R. NO - 6.8.2 ( 40mm thick)

-Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth, mixed with farmyard manure, supplied at the rate of 1.62 cum per 18 sqm, DAP 0.6kg, Chlorpyriphos 20%EC@ 0.20 litre per 18 sqm and supplying and planting hedge at 30 cm apart in two rows @ 202 no. well trimmed bushy ,multi-branched ,30 cm to 45 cm in height plants to be supplied in 15 cm x 15 cm poly bags per 18 sqm . (NEW HSR NO - 26.34)

-Providing and laying of chequered precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1 :4 (1 cement: 4 coarse sand). Ordinary cement without any pigment ( NEW HSR NO - 10.30.4)

-Wall painting on a cement plaster surface with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work ( NEW HSR - 11.71.1)

-Bridge Ladder: 10’L x 2’W x 6’H. Horizontal ladder is of G.I pipe jindal make 2”, ¾” & vertical ladder is of same material of 12 gauge ISI mark with suitable PU Primer & PU Paints. Complete item with GST, Transportation, Installation with C.C & labor at site with 2 years defect liability period free of cost to full satisfaction of engineer in charge.

-NS Item = Supply of RH Pipe 1" dia.

-Wave Slide: 9’.5 L x 5’H. Wave slide is of molded Fiberglass Reinforced Plastic (FRP) of 6mm thick and climbing ladder is of m.s pipe 1” x 12 gauge & m.s rectangular pipe

-Providing and fixing 3/4"dia Hydrant connection

-NS Item= Providing and Fixing mono block 1 HP motor Texmo make including GST, installation complete in all respect.

-Twister:- Providing, and fixing Twister of size 1700 X 1300 X 1300 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary

-(10260)Providing and stacking Azadirachta indica (Neem) of plants height 120-130 cm in big polybag of plants size 25 cm.

-(10283)Providing and stacking Ficus benghalensis (Bargard)height 120-135 cm in big HDPE bag size 25 cm.

-(10262) Providing and stacking Bauhinia blakeana (kachnaar) plants height 120-150 cm in big poly bags of plants size 25 cm

-(10271) Providing and stacking Cassia fistula (Amaltash) of plants height 120-135 in big poly bags of plants size 25 cm

-(10397)Supply and satcking of plants Nyctanthes arbor tristis (Harsingar) of ht. 90-105 cm in Eathen pot of size 20 cm

-(10291) Providing Ficus religiosa (peepal) plants height 150-165 cm in big HDPE bag size 30 cm.

-(10315) Providing and stacking Nauclea cadamba (Kaddam) plants height 150-165 cm in big HDPE bag size 25 cm

-(10319) Providing and stacking Phyllanthus emblica (Awala) plants height 150-165 cm in big HDPE bag size 25 cm

-(10336) Providing and stacking Scheichera trijuga (Kusum) height 150-165 cm in big poly bags of plants size 25 cm

Surender Kumar Contractor

Shanti Electrical Co.