ADDN ALTN TO DRAWING ROOM AND DINING HALL OF BLDG NO P 45 AT M MARG AND SPECIAL REPAIRS TO BLDG NO T 321 T 322 T 324 TO T 326 T 40 TO T 42 AT APG UNDER GE EAST DELHI CANTT 10

Amount

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws including taking down of old AC sheet roofing complete all as specified an directed. The sheets shall be procured from authorised dealer of manufacturer and work executed through authrised representative.

S & F pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws including taking down of old AC sheet roofing complete all as specified an directed.

M&L brick work with sub class B bricks, straight or curved on plan exc 6 m mean radious built in CM 1:6, including demolition of brick work built in cement mortar including all quoins, arches, pillars etc complete all as specified.all as specified and directed.

Dismantling framed trusses span n. exc 10m and structural steel complete all as specified and directed..

S&F rolled mild steel Fe-410w (Gde-E-250) quality 'B' as in Roof trusses (framed ) , trussed, purlins, crane gantries , rails and fastening and havy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls/ceiling etc including raking out joints, hacking for key, scrubing down with water etc complete all as specified and directed.

M&L rendering 15 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finishing the surface even & smooth without using extra cement complete all as specified & directed.

M&L rendering 15 mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finishing the surface even & smooth without using extra cement complete all as specified & directed.

M&L for 75mm th PCC 1:3:6 type C-2 using 40mm graded agg as in plinth protection finished even and smooth w/out using extra cement complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but n. exc 4 sqm each complete all as specified and directed.

S & F for rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings incl of steel Sheeting and hanging; also fastening and fixing, quality confirming to Fe-290 (Gde-E-165) complete all as specified.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & gap insert for top rail & bottom rail, paneling of plain color PVC sheet to be fitted in the MS frame, welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent complete all as specified & directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed.

S&F 200 mm long,aluminium,anodised, barrel tower bolts of extruded section all as described.

S&F 150 mm size aluminium handles,cast type,anodised all as directed.

S&F 100mm butt hinges extruded aluminium alloy with galvanised MS pin anodised type C22 all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed.

M & L for non skid ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 including dismantling of old tiles with backing complete all as specified and directed

All as per item No 19 but excluding dismantling of old tiles.

M & L for Glazed Coloured Ceramic tiles in vertical surface 300x450x7mm thick set and joint in neat cement slury and pointed in white or colour cement to match including rendering 10 mm thick in CM 1:4 including dismantling of old tiles with backing, complete all as specified and as directed.

All as per item No 21 but without dismantling of old tiles

S&F tubes medium grade galvanised steel with all fittings fixed to wall or laid in floors for 15 mm bore including taking up or down 15 mm dia GI tubing and connections including cleaning for re-fixing,or removing from site complete all as specified..

S&F tubes medium grade galvanised steel with all fittings fixed to wall or laid in floors for 20 mm bore including taking up or down 20 mm dia GI tubing and connections including cleaning for re-fixing,or removing from site complete all as specified..

S&F in repair rotational moulded polythene water storage tank three layered (Cylindrical vertical withclosed top)hoisted and fixed in position of 1000 ltrs capacity fixed with PVC tank nipples incl ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 20mm dia iron pipe and fixed ,complete all as specified in SSR Part I

S&F in repair vitreous chinaware counter type wash hand basin (WHB) white size 550mm x 400mm complete including provision of pair of mild steel angle iron brackets of suitable size duly painted, 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc complete all as specified and directed.

S&F in repair 15mm dia Pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-110gms complete all as specified.

S&F in repair 15mm dia bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed . (Minimum weight 15mm-90gms / 20mm-125gms) complete all as specified.

S&F in repair 15mm dia angle cock standard of PTMT any colour high pressure screwed for iron pipe and fixed . (Minimum weight 15mm-90gms) complete all as specified.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including P or S trap including provn of lime concrete bedding including connections to 'flushing cistern/pipe and PVC flushing cistern of 10 Ltr Cap complete all as specified and as directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm long complete all as specified and directed.

S&F soap dish chromium plated approximate size 160x160x90mm fixed with chromium plated brass screws complete all as specified.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Demolition of cement concrete of any description and in any position not other wise described complete all as directed.

M&L for PCC 1:3:6 type C 1, using 20 mm graded stone aggregate as surface channels and drains incl fair finishing complete all as specified.

Providing cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills,steps,and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, kneelers, apex stone, bed plates and the like including weathering slightly rounded or chamfered angles and throating, all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunchings against the sides of pipe after they are laid and tested for 150 mm dia pipe complete all as specified & directed.

M & L for RCC pipe NP-2 of 150mm bore, laid in trenches and jointed with collars as specified complete all as specified and as directed

S & F 75 mm thick SFRC man holes or drain covers perforated of any size and fixed in position complete all as specified and directed

S & F 75mm dia PVC (SWR) soil, waste, vent pipe in any length with or without ears with cement joints, single/double socketed, in any length with rubber ring joints, laid in trenches or floors or fixed to walls, complete all as specified.

S&F 75mm dia PVC (SWR) bends fixed with cement joint any radious complete all as specified.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in soil complete all as specified.

Removing excavated material (soil) n exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified.

Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore drain pipe complete all as specified.

S & F gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia complete all as specified.

M&L applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces exc 10 cm width or girth, complete all as specified and directed.

M&L three coat of white wash including preparation of new surfaces as on walls complete all as specified and as directed.

M & L applying two coats of cement based paint on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified.

Demolition, Cement concrete in ground floor and paving not exc 15cm thick below or above ground level complete all as specified.

M & L for 75mm thick cement concrete type C-2, 1:3:6 using 40mm graded aggregate as in sub base complete all as specified.

M & L for chequered cement concrete tiles of size 300x300x20 mm thick of approved design / pattern / size as in floor set and jointed in neat cement slurry and pointed with coloured cement including 15mm thick cement screed bed in CM 1:6 as all specified.

M&L Hardcore of broken bricks gauge n exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rolled /rammed to true surfaces complete all as specified

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation complete all as specified & directed.

M&L for RCC M-25 design mix (20mm graded stone aggregate) as in foundations footings, plinth beams etc all as specified & directed.

M&L for RCC M-25 design mix (20mm graded stone aggregate) as in beams, lintels etc all as specified & directed.

M&L for RCC M-25 design mix (20mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

S&F TMT bars upto 10mm dia and over, cut to length, bent to shape required,including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than .9mm dia complete all as specified.

Use and waste of form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and similar work, n exc 200mm thick (horizontal or sloping) complete all as specified.

Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintes,cantilevers, shelves including supports, overhangs, etc also splays between floors and beams finished rough surfaces of concrete complete all as specified.

M & L form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specified.

S&F for Plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases splices, angle brackets, cleats and other connections of Fe-410-W grade E-250 quality complete all as specified and as directed.

Providing & erecting double scaffolding, Jacks to support the structure provisionally during repair etc complete all as specified and as directed by Engr in charge.

Demolition of brick work built in cement mortar in any description and position, complete all as specified.

M & L for brick work with sub class B bricks of old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M & L hardcore of broken stone or boulders of gauge exc.63mm but n exc 100mm, deposited,spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface.

M & L for Vitrified tiles light Shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified.

M & L for Vitrified tiles light Shade 10mm thick (square/rectangular) on vertical surface, polished, area of each tiles not exceeding 0.36sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including backing coat of 10mm thick CM 1:4 on brick masonry/concrete surfaces finished even to receive tiles complete all as specified and as directed.

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

S&F 18/19mm thick Block boards, grade 1 quality, exterior grade with decorative type with decorative face veneer on both faces fixed with screws to timber frame-work or block board as in kitchen cupboards as in cupboards drawers or cupboards cabin or shutters etc complete all as specified and as directed by Engineer in charge

S&F Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails complete all as specified and as directed.

S&F 75mm extruded brass alloy handle fabricated type anodised complete all as specified and as directed.

S&F Drawer pulls brass, 4 screw plate with fixed dished pull; 80 mm to 100mm long complete all as specified and as directed.

S&F Drawer handles brass, projected ring (40mm x 50mm) on screwed plate, ring on 4 screw plate complete all as specified and as directed.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

M&L for 12mm thick blue tinted toughned glass including anodized aluminum snap beading, channels, glazing clips joint cleats, rubber gasket etc and other accessories complete all as specified and directed by Engr in charge.

M&L for double leaf glass door with 12mm thick blue tinted toughned glass door mounted on floor spring with hood open arm with top & bottom patch fittings including corner lock strike plate and european profile cylinder handle 32mmx300mm in SS finish as per approved design complete all as specified.

M&L for aluminum alloy powder coated door frame of section 100 mm x 44 mm x 1.5mm thick,door shutter top rail and both styles of size 100mm x 44 mm x 1.5mm thick,lock rail and bottom rail of size 115 mm x 44 mm x 1.5mm thick incl. aluminum snap beading and rubber packing, & 5.5 mm thick tinted glass/9mm thick both side laminated particle board, incl. 100 mm long aluminium butt hinges - 04 Nos each leaf, 200 mm long tower bolt, 200 mm long Aluminium handle- 02 Nos on each leaf, 4 lever lock brass 100 mm long mortice lock, & hydraulic door closer heavy duty suitable for 1 m wide shutter for each leaf complete all as specified and directed by Engr-in-Charge.

S&F anodized aluminum alloy powder coated standard hollow section for window three tracks including aluminum frame/chowkhat with following specifications including anodized aluminum snap beading, channels, 5mm thick tinted glass, glazing clips joint cleats, rubber gasket etc and other accessories complete all as specified and directed:- (a) Frame of section:- 83.50mm x 44.45mm x 1.60mm thickness (b) Sliding window section (Channel):- 61.85mm x 31.75mm x 1.2mm thickness (c) Sliding shutters of section:- 40mm x 18mm of 1.20mm thickness with locking arrangement Note:- (1) The rates also including the cost of cutting, waste and making good disturbed surface matching with existing surface and finish as directed (2) Minimum thickness of powder coating shall be 50micron

S & F powder coated aluminium ventilators with top hung shutter incl 75mm long alm butt hinges - 02 nos, alm hoock & eye-01 No, 100 mm long alm handle-02Nos, 100mm long Alm tower bolt-02 Nos on each shutter including 4mm thick tinted glass complete and all as specified and directed by Engr-in-Charge.

M&L Rendering 5mm thick on concrete surfaces in CM 1:3 as on ceiling all as specified and as directed.

S&F suspended gypsum board with POP ceiling in steps including vertical/sloping members includes with GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) alongwith perimeter of nailing screw fixed in brick wall/RCC with the help of nylon seelves and screws at 610mm centre, then suspending GI intermediate channels of size 45mm (0.9mm thick with two flange of 15mm each) from the soffits at 1220mm centre with GI cleat and steel expansion fasteners, ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm centres, 12.5mm tapered edge gypsum board conforing to IS 2095 (1982) is then screw fixed to ceiling section with 25mm drywall screws at 230mm centre,. Screws fixing is done mechanically either with screw driver or drilling machine with suitable attachment finally the board are to be jointed and finishing the tapered and square edges of the boards are to be joints compound, joint fiber tape. Note :- Details of fixing & material will be got approved by GE before commencement of work.

All as per srl item No 84 here in before but on vertical surfaces width n exc 20cm completed all as directed.

M&L for Preparing new plastered surfaces of walls and applying two coats of exterior emulsion paint (Weather Coat) over a coat of priming paint etc complete all as specified

M&L for prepration of new or old plastered or unplastered surfaces of wall and applying alayer of wall care puty 3 mm thick to make the surface smooth for receiving wall finish& applying two coats of Oil bound distemper complete all as specified and directed.

S & F fancy type 15mm bore CP angle valve/ stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified.

S & F 15mm bore, fancy type two way bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by the Engineer-in-Charge.

S & F fancy type 15mm bore CP stop valve two-in-one, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified.

S&F sheet glass shelf assembly of 600 mm consisting of 5.5mm thick sheet glass shelf with chromium plated brass brackets guard and railing complete all as specified (Make : Jaquar, Cat Pt No-ACN-1171N or equivalent from the list).

S&F sheet glass corner shelf assembly of 300 mm consisting of 5.5mm thick sheet glass shelf with chromium plated brass brackets guard and railing complete all as specified (Make : Jaquar, Cat Pt No-ACN-1173 or equivalent from the list)..

S&F CP brass towel rack 600mm long fixed to wall with CP screws complete all as specified (Make : Jaquar, Cat Pt No-ACN-1181Sor equivalent from the list).

S&F Frameless Corner shower enclosure with two fixed glass and openable door fixed on the front panel - 3 part Glass: 8mm Finish: Chrome H: 1950 W: 1600-2000 all as specified (Make : Jaquar Model No. 1840-G Cat No JSE-CHR-840G1620H19X) or equivalent in other approve make as specified.

S & F Shower panel size 1500 x 200mm stainless steel structure, 3 adjustable vertical jets (Square), integrated shower head (8" square), Thermostatic mixer with diverter, hand shower with flexible hose, button spout, connecting hose including complete accessories for fixing complete all as specified. (Jaquare Cat No JPL-BLK-JA011) or equivalent in other approve make as specified.

S&F Stainless steel towel rail 600mm long with lower hangars fixed to wall with CP screws complete all as specified(Make : Jaquar, Cat Pt No-ACN-1181S) or equivalent in other approve make as specified.

S&F CP brass towel ring fixed to wall with CP screws complete all as specified(Make : Jaquar, Cat Pt No-ACN-1121BN) or equivalent in other approve make as specified.

S&F soap dish , fancy type, fixed to walls with chromium plated brass screws complete all as specified(Make : Jaquar, Cat Pt No-AQN-7731) or equivalent in other approve make as specified.

S&F Soap dispensor with mettalic bottle complete all as specified and as directed. Make : Jaquar Cat Pt No ACN-1137N)or equivalent in other approve make as specified.

S&F CP toilet papper holder with stainless steel fixed to wall with CP screws complete all as specified(Make : Jaquar, Cat Pt No-APN-35751P) or equivalent in other approve make as specified.

S&F CP bottle trap with connection fixed to wall with CP screws & connection to tap complete all as specified(Make : Jaquar, Cat Pt No-ALD-769L) or equivalent in other approve make as specified.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore complete all as specified..

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore complete all as specified..

S&F rotational moulded polythene water storage tank three layered (Cylindrical vertical withclosed top)hoisted and fixed in position of 1000 ltrs capacity fixed with PVC tank nipples incl ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 20mm dia iron pipe and fixed ,complete all as specified in SSR Part I

S & F ISI marked 20mm bore stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed.

S & F ISI marked 15mm bore stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified.

S & F 100mm bore cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge

S & F of 100mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed by the Engineer-in-Charge

S & F of 75mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed by the Engineer-in-Charge

M & L for 75mm bore dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 complete all as specified and as directed by the Engineer-in-Charge

S&F 150mm internal dia of SGSW pipes laid in trenches and jointed with cement mortar 1:3 complete all as specified and directed.

S&F vitreous chinaware table top wash hand basin (WHB) of size 595mm x 440mm x 185mm complete including 32 mm dia chromium plated waste coupling, PVC waste pipe etc complete(Make : Jaquar Cat No : KUS-WHT-35901) or equivalent in other make as per list of make .

S&F single piece WC with UF soft close seat cover, Hinges, Fixing Accessories Set and Accessories Set, Cistern fittings, Size: 366 x 655 x 765mm, S Trap-300mm vitreous china, pedestal pattern European type 32 mm dia PVC flush pipe and connection to drain, complete all as specified(Make : Jaquar Cat Pt No LYS-WHT-38851S) or equivalent in other make as per list of make.

S & F CP jet spray with pvc pipe complete all as specified.

S&F CP health foucet with connection fixed to wall with CP screws & connection to tap complete all as specified (Make : Jaquar, Cat Pt No-ALD-CHR 593N) or equivalent in other make as per list of make .

M&L for water proofing treatement to RCC roof slabs, walls, chhajjas etc, shall be carried out as specified below and as directed by Engineer-in-Charge. (a) Rendering 15mm thick in CM 1:3 on concrete surfaces of roof,Chajja.parapit etc (b) Preparing plastered surfaces of roof slabs, walls, chhajjas etc, by brooming with broom sweeping free from dirt dust etc & evenly applying a coat of approved bituminous primer @ 0.20 kg/sqm of area complete all as specified. (c) Laying APP polymer modified approved membrane, non woven, polyester, weighing not less than 3.5 kg/sqm with laps & overlaps as specified & joints sealed and applied complete by torch application method all as specified & directed by Engineer-in-Charge including removing existing treatment and surface prepration for new treatment. (d) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/Sqm on the top of membrane surfaces complete all as specifed & as directed by Engineer-in-Charge.

Demolition , cement concrete (reinforced) of any description and in any position not otherwise specially provided for complete all as specified.

Taking down carefully copper/aluminium point wiring from wooden battan or conduits (light, fan, socket or power) complete including (fittings such as switches, ceiling roses, pendants, regulator, sockets etc. to be measured separately) and making good disturbed surfaces of walls, floor etc.

Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non-metalic rigid PVC conduit medium grade ISI Marked and all conduit accessories concealed in wall/ceiling/fixed to roof/truss/columns etc and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty conductor, fabricated branded modular metal flush box duly make embossed, concealed in walls with suitable modular inner and outer plate for housing switches , socket out let and fan regulators etc , all as specified and as directed for the followings:-

(a) One light/Fan/Bell point controlled by one switch

(b)One socket outlet point 5/6 Amps on independendent board

(c ) One socket outlet point 5/6 Amps controlled by one switch on same board along with other switches.

All as per item No 119 above but with copper conductor cable FLRS 2.50 sqmm for one 3 pin socket outlet,15 Amps concealed and including provision of 2.50 Sqmm PVC insulated copper conductor cable as earth continuity conductor on independent board.Make for wiring cable.

S&F in repair Sub main wiring complete with two runs of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable with one run of 6 sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 20 mm dia non metallic rigid PVC conduit and conduit accessories(Concealed) in walls all as specified and as directed.

M&L for switch piano flush type, single pole, one way, 5/6 Amps complete all as specified and directed.

M&L for switch piano 15 Amp, single pole, flush type, one way complete all as directed.

M&L for socket outlet 2-in-1, 5/6 Amps flash type complete all as specified and directed.

M&L for socket outlet 2-in-1, 5/6 Amps and 3 pin 16 amp flash type complete all as specified and directed.

M&L of Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps with and including pressed steel powder coated MS sunken box of suitable size, covered with & including 3 mm thick bakelite, laminated hylem sheet top cover and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed. Note : The cost of MS sunken box and bakelite sheet is included in the quoted rate.

S&F LED batten luminaire surface mounted, 4 feet system wattage of 22 Watts with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 10%, colour temperature - 6500K, surge protection 2.5KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level ≥ 100 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed.

Supply and fixing of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc and making all necessary connections complete all as directed.

Supply and fix in repair MCB C curve type SP 10 to 32 Amps 240 volts 10 KA 50 HZ C curve complete.

Supply and fix in repair MCB C curve type SPN 32 to 40 Amps 240 volts 10 KA 50 HZ C curve complete.

Material and labour for laying of LT underground cable XLPE insulated, PVC sheathed, galvanised steel strip / wire armoured, aluminium conductor, 1100 volts grade, of size 10 Sqmm 2 core suitable for earthed system laid in duct / trench / along pole / wall etc including making connection complete all as specified and directed. Note : 1. The cost of AI thimbles/lugs and cable galnd etc is incl in quoted rate and no extra payment will be made for it. 2. The excavation, earth work, sand cushioning and brick protection etc will be measured and paid seperately.

M&L sand cushioning with a layer of fine sand 8cm thick before laying the cable and 15 cm after laying the cable in trenches to cover under ground cable complete all as specified .

M&L for brick proctection to cable using old size class 'B' bricks, laid flat, dry but jointed, laid lengthtwise perpendicular to the axis of cable complete all as specified and directed.

Supply and fixing of LED security light luminaire 40 watt (white) pressure die cast aluminium housing with heat resistance toughned glass & IP-68 protection with and including driver/transformer complete all as specified and directed.

Supply and fixing of street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40mm dia size light grade complete with nut, bolts, washer etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed.

M&L for earthing complete with GI earth plate electrode 600 mm x 600mm x 6mm thick burried directly in ground not less than 2.25 mtrs below ground level, with top edge of the plate not less than 1.5 mtrs deep below normal ground level, connected to galvanised earth wire 4mm by means of bolts, nuts check nuts to earth test point including necessary PCC 1:2:4 type B-1 pit, cover frame, GI pipe 15mm dia light grade for protection of earthing lead and GI pipe 20mm dia for watering pipe with funnel, wire mesh, salt, charcoal dust and excavation complete all as specified and directed

M&L for Modular switch 6 Amp, 1 way, 1 module size complete all as directed. Make Havells/Legrand/SSK/Roma

M&L for Modular switch 16 Amp, 1 way, 1 module size with indicator lamp complete all as directed.Make Havells/Legrand/SSK/Roma

M&L for of Modular socket 6 Amp, 2/3 pin, universal type, 2 module size complete all as directed. Make Havells/Legrand/SSK/Roma

M&L for Modular socket 16 Amp multipurpose shuttered type, 2 module size with indicator lamp complete all as directed. Make Havells/Legrand/SSK/Roma

S & F of Modular Fan regulator step type, 1Module size complete all as directed. Make Havells/Legrand/SSK/Roma

M&L for Modular Bell push switch 6 Amp 1 module size complete all as directed. Make Havells/Legrand/SSK/Roma

Material and labour in replacement for TV Wiring with Co axial RG-6 heavy duty PVC insulated, PVC sheathed cable having single strand of 0.7 mm dia taped suitable for telephone wiring and making all necessary connections from terminal box to TV socket, drawn in separate concealed PVC conduit complete all as directed. Make : Standard/ Havells/RR Cable. Note : The PVC Conduit and conduit accessories shall be included in quoated rate and will not be paid separatelypaid separately .

Supply and fixing in replacement of Modular TV socket (RJ 11 Socket Jack) 01 Module size socket as per site requirement complete all as directed by the Engr-In-Charge. Make Havells/Legrand/GM

Material and labour in replacement of telephone Wiring with twin core PVC insulated, PVC sheathed cable having single strand of 0.7 mm dia taped suitable for telephone wiring and making all necessary connections from terminal box to telephone socket, drawn in separate concealed PVC conduit complete all as specified and directed. Note : Make of cable : Havells, Rallison,L&T

M&L in replacement of Modular Telephone socket Jack 01 Module size complete with modular sheet as per site requirement complete all as directed by the Engr-In-Charge.

S&F in repair Sub main wiring complete with four runs of 16 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable with two run of 16 sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 20 mm dia non metallic rigid PVC conduit and conduit accessories(Concealed) in walls all as specified and as directed.

Supply and fixing of LED mirror light fitting 12 watt and making all electric connections complete all as directed. Make : Syska/Havells/Philips/CG. Part No SSK-T5-12W

S & F in replacement of wall mounted LED light of capacity 9W including LED bulb as per sample and all electrical connection completed all as specified. Make :-Halonix Cat Part-HLWB-01-B22 or equivalent in Havells/Philips

Supply and fixing of electric bell of DINGDONG type, 6 Amps, 240 volts, single pole and making all necessary connections complete all as directed. Make : Anchor/SSK/Cona

Supply and fixing in repair MCCB incommer Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, VTPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc and making all necessary connections complete all as directed.

S & F of MCCB 3 Pole 100 Amps with over load and short circuit protection and rupturing capacity not less than 16 KA as specified and directed.

S & F in replacement of Energy efficient wall mounted LED Bulk Head luminaire 10W made of die cast Aluminium with Opal diffuser IP-65 complete all as specified and directed.

Supply and fixing of Modular Ac Box including MCB SP, C Curve type of capacity 32 Amp, 10 kA modular switch type and modular socket complete all as directed.

S & F of LED Recess/Surface mounting light 12W incl driver complete all as specified.

Supply and fixing of Ceiling fan 1400mm sweep 230V 50Hz, copper winding ISI marked single star rating incl electric connections and hanging rod of appropriate length as per site requirement as directed by Engr-in-Charge.

Supply and fixing of Wall mounted fan 400mm sweep 230V 50Hz, copper winding incl electric connections complete all as as directed by Engr-in-Charge.

Supply and fixing of Ventilating fan 250mm sweep 230V 50Hz, copper winding incl electric connections complete all as as directed by Engr-in-Charge.

Supply and fixing of storage water heater 50 Ltr capacity,SS tank 5 star rating incl fasteners, 2 Nos wireArmoured type PVC Connections complete all as specified and directed.

Supply and fixing in replacement of automatic hand dryer hot air dispenser with infrared sensor 5 star ratings metal body with all accessoried including electrical connections complete all as specified.

S & F in replacement of bed side light including 9 W LED lamp, fancy wall mounted type including fixing accessories complete all as specified and directed.

M/s M M BAHL

M/S Yamin

mtechassociates

Vipul Construction

Powerlite Engineers

n s kumar and sons