Construction of shed for Project HCP-54 and MLP 304mission waste to wealth at AMPRI, Bhopal

Amount

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:

All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form work for :Columns, piers, abutments, pillars, posts and struts, footing.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :: 1:1.5:3 (1 cement : 1.5 coarse sand (ZoneIII) : 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a approved steel primer & paint all complete

Providing and fixing bolts including nuts and washers complete

Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer & paint using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets,

12 mm cement plaster of mix :1:4 (1 cement: 4 sand)

18 mm cement plaster in two coats under layer 12 mm thick cementplaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Providing and laying 60mm thick factory made rubber moulded cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of stone dust filling the joints with fine sand and sides shall be locked with concrete 1:2:4 etc. all complete as per the direction of Engineer-in-charge.

Supplying and filling moorum/kopra, base of floor/rooad etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by Vibratory roller and watering, levelling etc complete

Brick work with chimny brick of RAVI/KAVI/ SHREE/A D in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and applying multicoat synthetic plaster as per approved design, pattern texture in 2 mm thick on new plastered surface finished in proper line and level as directed by Engineer-in-charge in five coats consisting of composition of four order of application given as under includig all materials, labour and scaffoldings etc. 1) Scrapping of the new surface and applying sealer primer mixed with water in the ratio 1:3 (part sealer primer : 3 part water) and applying by brush @ 0.25 kg/sqm. 2) Applying levelling coat of spectrum rustic fine or equivalent with trwel as a putty finished to generate required texture by trowel. 3) Applying third coat of synthetic plaster with trwel @ 2.5 kg/sqm finished to generate required texture by trwel. 4) Applying two coats of exterior super fine pigmented acrylic wall coating as top coat @ 0.5 kg/sqm in two coats and colours as approved by Engineer-in-charge all up to a height of 10m.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 20 mm thick including fixing in skirting

Providing and fixing Glazed Aluminium sliding powder coated 50 microns in Door & windows including all fittings, handles,locks door closer etc complete

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters . 80 X 125 MM M.S laths with 1.25 mm thick top cover with mechanical device chain and crank operations for operating rolling shutters(Geared)

Labour for shifting of machines,jungle clearance, junk clearance etc

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting rain water guter of suitable size etc. complete.

Providing and fixing 2 mm thick polycorbonate sheets including all fixtures and fittings etc complete

Providing and fixing Z - 200 purlins 2.0 mm thick with pre-painting etc complete

Providing and fixing rain water gutter size 200x150x150 mm madeup of 0.50 mm thick Color coated galvonium sheet including all fixtures and fittings etc complete

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes100 mm dia conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including fixing of clips, bends/shoe etc complete as per direction of E-in-C

Providing and fixing on roof TURBO Vent 600 dia with all accessories, fittings etc complete as per direction of E-in-C

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box/celling rose and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group 'C'.

Wiring for circuit / submain wiring alongwith earth wire with the following size of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required

a) 2 X 1.5 Sq.mm + 1 X 1.5 Sq.mm earth wire.

b) 2 X 2.5 Sq.mm + 1 X 2.5 Sq.mm earth wire.

c) 2 X 4 Sq.mm + 1 X 4 Sq.mm earth wire.

d) 2 X 6 Sq.mm + 1 X 6 Sq.mm earth wire..

e) 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

f) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6pin 15 / 16 & 5 / 6 amps modular socket outlet and 15 / 16 amps modular switch, connection, painting etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar,din bar, interconnections, powder painted including earthing etc.as required. (But without MCB/RCCB/Isolator)

12 way double Door

Supplying & Fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" Curve including connections, painting etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps 'c' series, SP, MCB, in sheet steel enclosure, on surface or in recess with chanined metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required

Providing and fixing 25 mm X 5 mm G.I. strip on surface/Wall or in recess with G.I. nut, bolt, spring, washer connections etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240 volts 'C' series, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

a) Single Pole

b) Single Pole and Neutral

c) Triplae pole with neutral

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminium conductor cable of 1.1 KV grade as required

a) 3 1/2 x 70 sq.mm

Supplying and fixing follwing modular Switch/Socket on the exixting modular plate & switch box including connections excluding moddular plate etc as required.

b) 3 pin 5/6 Amps Socket outlet

c) 15/16 A switch

d) 6 pin 15/16 A socket outlet

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (Make - BEC/Kissan/Kasta/ Supreme/ Sudhakar/ Reliance)

Supplying and fixing of following sizes of steel conduit alongwith accessories in surface/recess including painting in case ofsurface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of following ways surface/ recessmounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required .

a) 4 Way (4+12), double door,

Supplyiong and Fixing following size/ Modular plate, GI box alongwith modular base & cover plate for modular switchesin recess ets as required

6 module

Supplying and Fixing TP sheet steel enclosure on surface/recess along with 32 amps ,415 volt 'C' curve TP MCB complete with Connection ,testing and commissioning etc as required

Supplying & laying at site XLPE Insulated PVC Sheathed steel Armoured under ground Electric cable with aluminium conductor for working voltage upto and including 1100 Volts to IS:7098 (Part-1) or IS:1554 (Part-I) with latest amendment as applicable of size 3 1/2 x 70 sqmm (make :Finolex /CCI/Polycab/ RR kable)

Supplying, installation, testing and commissioning of Air circulautor fan 450 mm sweep min 1350 RPM , 100 CMM at the wall ,thermal overload protection for long lasting motor, royale finish and smooth oscillation (similar to Crompton make model Storm2 ) including all accessories,connection complete as required.(Make : Usha /Havells/ Crompton/Khatain)

Supply and installation of Mid way light having minimum 40 watt Envoimental friendly, energy saving long life corresion resistance mounting in tracess/recesses/ surface with provision of hanging of Tracess and surface for proper light having IP65 LED light.

Supplying installation testing & commissioning of 60-80 watt integral LED flood light fitting with driver inside a PDC Housing, IP 66 based energy saving envoirmetal friendy highly efficient, reliable with Driver & all accessories i/c connection complete etc. as required.

Supplying installation, testing and commissioning of 3 pole 160Amp MCCB 25 KA, in existing panel including interconnection etc.as required (make legrand/hager /semans/L& T)

Supplying and fixing following rating, four pole, 10KA, 415 V, isolatorin the existing MCB Distribution board complete with connections, testing andcommissioning etc. as required

P N NAYAK

MAITRI ENTERPRISES