Loading
Loading…
Loading…
Tender Value
₹20.3 L
EMD Value
₹40,700
Closing Date
9 Apr 2026, 10:30 amClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
45 days
Expenditure
Revenue
HQ
6 conditions · 2 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
As per Part I Offer Letter, Part II General Instructions to tenderer and Tender Conditions & Annexures-Attached
Need based maintenance of flight roller conveyors at Mould room
RWF-M-OT-MMR-2025-26-91
RWF-M-OT-MMR-2025-26-91
Open
Works - General
24 Months
Bengaluru Urban, Karnataka
₹0
₹40,700
9 Apr 2026
18 Mar 2026
26 Mar 2026
2 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| Weekly Schedule- I a). Inspection of main chain, replace damaged out board rollers, bearings, pins and top and side link plates and check for proper tension of main chain. b). Inspect slave roller sprockets, rollers, chain and replace defective ones. c). Inspect main drive gear box, couplings, drive belts, pulleys, intermediate shaft, bearings and replace if found defective. Check oil level of drive gear box and top up if necessary. e). Check for smooth operation of the escapement. Inspect escapement cylinder pins & hoses and replace if found defective. Clean the equipment & its surroundings. f). Check return tracks tail and drive ends bends and replace if defective. g) Inspect counter weights and its pins of D-13, 14, C-20 & 21. Tension main chain of C-3 if necessary. h). Check of FRC tracks for damaged square rods and wear plates, if found damaged same to be welded. i). Oil trenches in the basement to be cleaned (drive & tail end).(Rates are inclusive of GST) | — | 52.00 | — | — | |
| Half yearly schedule- II a). Inspect triplex & duplex chains, sprockets & shear pins and replace if necessary. b). MHO C20, C21, D13 & D14 RC fan assembly to be checked for smooth operation and rectify if found to be defective (bearings, belts, pulleys, shafts and fastners of RC fan need to be checked) c). All take-up bearing to be checked and lubricated. d). Check for gear box oil leakages, replace damaged oil seal / defective gear box. e). Check for side and roof panel sealings and arrest leakages if any. (Rates are inclusive of GST) | — | 2.00 | — | — |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
PartIOfferletter.pdf
ATTACHMENT
PartIIInstructionstoTenderers.pdf
ATTACHMENT
PartIIISpecialconditions.pdf
ATTACHMENT
PartIVPricesandpayments.pdf
ATTACHMENT
PartVBreakupofratesandschedule.pdf Part V Breakup of rates and schedul
ATTACHMENT
PartVIAnnexures.pdf
ATTACHMENT
PartVIINITforetender.pdf
ATTACHMENT
Part VIII GCC doc
ATTACHMENT
PartVBreakupofratesandschedule.pdf
ATTACHMENT
GCC_April-2022_merged_compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .