REPAIR/ MAINT/ UPKEEP OF EXTERNAL ELECTRIC SUPPLY, LT DISTRIBUTION LINE, PANEL AND CONNECTED ITEMS AT MHOW UNDER GE (MCTE) MHOW

Amount

Attending to no light any type complaints and carrying out electrical break down electric complaints such as faulty cable of defective items like service cables, MCB's, MCCB's, upto DB's, digging work etc. through skilled trademen at any location complete all as specified and directed by Engr-in-Charge. Note:- (i) Contractor or his representative will report daily to the AGE E/M-III Yard MCTE MHOW at 9:00 AM to collect the complaints in the various locations of AOR of AGE E/M-III MHOW. (ii) Each complaint shall be attended/ check on same day and be resolve within 24 Hrs otherwise @ Rs 500/ per complaint to be recovered from quoted rate. (iii) Multiple job cards or multiple complaints on one job card may be issued at a time based on the complaints available daily. Contractor will ensure sufficient manpower to resolve the issues with in time line given above. (iv) Rates quoted for this item is includes manpower/ labour reqired for collection for complaints from office, reporting labour/engineer on site, reporting feedback to the authority and transportation reqired for the same. Cost of T&P reqired for execution of work shall also deemed to be included in quoted rates. (v) Contractor or his representative will submit daily report on the status of complaint resolved and pending with reason. (vi) Cost of miner parts/ material i.e screw, nails, washers, saddle, fuse, minor requirement of 2/3 core wire, insulation tap, different type of Lugs etc required to making the article serviceable/ working at site shall deemed to be included in quoted rates.

S&F service cable un armoured of size 4 sqmm 2 core,1100 volts grade, heavy duty cable with PVC insulated solid aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed including taking down old/ unserviceble service wire complete all as specified and directed.

Disconnecting & dismentling of damaged/ unsv cable any type/ make and Supply & laying (in repair) cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor using lugs bothe end of cable & wrapping pvc tape over XLPE insulation cable and testing complete all as directed for following size:- (Note:- Excavation & earth work, sand cushioning, bricks protection & GI pipe where required shall be measured & paid seperately)

(a) 16 Sqmm 4 core

(b) 25 Sqmm 3.5 core

(c) 35 Sqmm 3.5 core

(d) 50 Sqmm 3.5 core

(e) 70 Sqmm 3.5 core

(f) 95 Sqmm 3.5 core

(g) 120 Sqmm 3.5 core

Excavation in trenches in soft/ loose soil not exceeding 1.5 M wide and not exceeding 1.5 Mtr deep and getting out including filling bottom surface to required level or slope for laying of pipes/ cables complete all as specified and directed.

Returning filling including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft soil complete all as specified and directed.

Removing excavated surplus soil not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed.

M&L for sand cushioning with dry local sand for cable protecting under ground cable (8 cm before laying the cable and 15 cm after laying the cable) in trenches including punning the sand upto 18 cm thick and consolidated complete all as specified and directed. Note:- Punned thickness 18 cm shall be measured only.

Supply and laying sub class 'B' bricks laid dry and flat across the length of cable for protection of cable including taking down old/ broken bricks complete all as specified and directed.

M & L for bore hole for passing cable through/ insertion of 80/ 50mm dia GI pipe under PCC road/ taxi track/ runway/ hard standing upto the depth 450mm to 1200mm complete all as specified and directed. Note:- (i) Cost of equipments, tools & plants,material required for boring shall be deemed to be included in unit quoted rates above. (ii) GI pipe 80/50mm dia shall be measured and paid separetely.

S&F for 50mm dia GI pipe 'light grade' ISI marked including fittings such as bends, tees, sockets etc fixed on wall/ pole or laid in trenches under road crossing/ hard standing including taking out old/ unserveciable existing pipe complete all as specified and directed. Note:- Excavation and earth work shall be measured & paid separately.

S&F for 80mm dia GI pipe 'light grade' ISI marked including fittings such as bends, tees, sockets etc fixed on wall/ pole or laid in trenches under road crossing/ hard standing including taking out old/ unserveciable existing pipe complete all as specified and directed. Note:- Excavation and earth work shall be measured & paid separately.

M&L for hiring Fault locator Megger machine, Locating fault in HT/ LT UG cable of any size complete all as specified and directed Note:- (i) All the instruments and T&P required for the above job shall be arranged by the contractor at site and cost of the deemed to be included in the above rates. (ii) Contractor should be provide two labours for Joining and dismentling of cable at both the end and excavation above the faulty cable if reqd

Supply, jointing and testing cable jointing kit for 1100 volt grade cable for cable straight trough heat shrink type joint complete with jointing material & accessories for 3.5 core XLPE cable of size 25 Sqmm to 50 Sqmm insulated armoured aluminium cable including taking down old/ unserveciable joint kit complete all as specified and directed.

Supply, jointing and testing cable jointing kit for 1100 volt grade cable for cable straight trough heat shrink type joint complete with jointing material & accessories for 3.5 core XLPE cable of size 70 Sqmm to 120 Sqmm insulated armoured aluminium cable including taking down old/ unserveciable joint kit complete all as specified and directed.

Supply, jointing and testing cable jointing kit for 1100 volt grade cable for cable straight trough heat shrink type joint complete with jointing material & accessories for 3.5 core XLPE cable of size size 150 Sqmm to 185 Sqmm insulated armoured aluminium cable including taking down old/ unserveciable joint kit complete all as specified and directed.

M&L for preparation of steel surfaces of indoor/ outdoor elect panel of any size/ type and removing dust, dirt by cleaning/ scrubbing inside outside as required, welding/ fixing and providing fresh hinges/ screw/ nut bolts as required and fixing the panel door including painting the external surfaces with one coat of synthetic enamel paint without disturbing the existing fittings and fixture, changing of unserviceable voltmeter, ammeter, indicator lamp, proper taping to incomming outgoing LT UG conductor with flexible tape and insulation tape including marking and writing letter such as SM No. capacity etc. with safety precaution complete all as specified and directed.

M&L for bus bar box of sheet metal 3mm thick powder coated, having 4 Nos. aluminium bus bar of rating 200 Amp mounted on insulator including 01 No. of MCCB 4 pole 63 Amp 415 volts with thermal magnetic release as incomer, breaking capacity 25 KA inside the box and suitable fixing arrengement like flat iron clamp of size 25 x 3mm with hinged cover & locking arrangement including grouting of feeder piller box 60 cm above ground level by providing 90 cm long angle iron of size 40 x 40 x 6mm welded on all the four corner embedded in PCC 1:2:4 using 20mm graded stone aggregate complete duly painted with two coat of synthetic enameled paint over a coat of red oxide primer fixed in repair outdoor type duly fitted on complete all as specified and directed.

Supply, installation and testing of factory made, CPRI Approved cubical outdoor type feeder pillar box 415 volt, 4 wire, AC 50 Hz, made out of 3.15mm thick CRCA sheet, weather and vermin proof powder coating finish bothside (interior & exterior) for outdoor mounting with having degree of protection as per IP-56 complete factory lock two earth terminal suitable cable gland for all incoming and outgoing and removable neutral link,Both Side openable double door Indicating light LED type RYB - 01 Set, Ammeter-01, Voltmeter-01, connecting strip/ solid conductor brought out to cable chamber brass/ copper nut, bolts/ washer etc including grouting of feeder pillar box 60 cm above ground level including suitable size angle iron stand made up of 65 x 65 x 6mm welded on all the four corner embedded in PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) upto 30 cm including excavation and earth work complete including taking down u/s panel with following asseccories:- (a) Aluminium busbar high conductivity 800 Amp rated 4 phase including neutral bus bar complete - 01 No. Incoming:- (b) MCCB 4 -pole 400 Amp make-Havells, 415 Volt, breaking capacity 36 KA, 50 HZ with thermal magnetic release - 01 No. Outgoing:- (c) MCCB 4 - pole 100 Amps breaking capacity 25 KA, 50 HZ - 04 Nos. (d) MCCB 4 - pole 63 Amps breaking capacity 25 KA, 50 HZ - 02 Nos.

Supply, installation and testing of factory made, CPRI Approved cubical outdoor (Kiosk) type feeder pillar box 415 volt, 4 wire, AC 50 Hz, made out of 3.15mm thick CRCA sheet, weather and vermin proof powder coating finish bothside (interior & exterior) for outdoor mounting with having degree of protection as per IP-56 complete factory lock two earth terminal suitable cable gland for all incoming and outgoing and removable neutral link, Both Side openable double door Indicating light LED type RYB - 01 Set, Ammeter-01, Voltmeter-01, connecting strip/ solid conductor brought out to cable chamber brass/ copper nut, bolts/ washer etc including grouting of feeder pillar box 60 cm above ground level including suitable size angle iron stand made up of 65 x 65 x 6mm welded on all the four corner embedded in PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) upto 30 cm including excavation and earth work completeincluding taking down u/s panel with following asseccorie :- (a) Aluminium bus bar high conductivity 600 Amp rated 4 phase including neutral bus bar complete - 01 No. Incoming:- (b) MCCB 4 pole 400 Amp 415 Volt, breaking capacity 36 KA, 50 HZ with thermal magnetic release - 01 No. Outgoing:- (c) MCCB 4 - pole 200 Amps breaking capacity 25 KA, 50 HZ - 01 Nos. (d) MCCB 4 - pole 100 Amps breaking capacity 25 KA, 50 HZ - 01 Nos. (e) MCCB 4 - pole 63 Amps breaking capacity 25 KA, 50 HZ - 06 Nos.

S&F MCCB 63 Amp, 4 pole, 415 Volt ISI marked conforming to 'B" curve, breaking capacity 16 KA complete including taking down complete all as specified and directed.

S&F MCCB, 4 pole, 415 volts, 400 Amps, breaking capacity 36 KA, with thermal magnetic release adjustable type including taking down old/ unserviceble MCCB complete all as specified and directed.

S&F MCCB, 4 pole, 415 volts, 315 Amps, breaking capacity 36 KA, with thermal magnetic release adjustable type including taking down old/ unserviceble MCCB complete all as specified and directed

S&F MCCB, 4 pole, 415 volts, 250 Amps, breaking capacity 35KA/ 36 KA, with thermal magnetic release adjustable type including taking down old/ unserviceble MCCB complete all as specified and directed.

S&F MCCB, 4 pole, 415 volts, 200 Amps, breaking capacity 35KA/ 36 KA, with thermal magnetic release adjustable type including taking down old/ unserviceble MCCB complete all as specified and directed.

S&F MCCB, 4 pole, 415 volts, 160 Amps, breaking capacity 35KA/ 36 KA, with thermal magnetic release adjustable type including taking down old/ unserviceble MCCB complete all as specified and directed.

S&F MCCB, 3 pole, 415 volts, 100 Amps, breaking capacity 16 KA, with thermal magnetic release adjustable type including taking down old/ unserviceble MCCB complete all as specified and directed.

S&F MCCB, 3 pole, 415 volts, 63 Amps, breaking capacity 25KA, with thermal magnetic release adjustable type including taking out existing old/ unserviceble MCCB complete all as specified and directed.

S&F MCB TPN, 4 pole, 415 volts, 63 Amps,'B' curve 10 KA complete all as specified and directed.

M&L for earthing with galvanized steel earth plate electrode 600 x 600 x 6.0mm thick buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanized iron 32 x 6mm strip as earthing lead protected by GI pipe light grade 40mm bore for protection of GI earth strip and 20mm dia GI pipe medium grade for watering with alternate layers of charcoal/ coke and salt including all accessories like nut, bolts, reducer, nipple, wire meshed/ screened funnel and making brick masonry finished chamber of internal size 300mm x 300mm x 300mm with concrete base, covered with a cast Iron hinged cover resting over the cast iron frame painted with black bitumastic paint which shall be embedded in the block masonry including excavation works, refilling, connected to main switch/ MCB DB for feeding the electric supply complete including taking down of old u/s earthing complete all as specified and directed as shown in electrical plate No. 3 of SSR Part-I and testing of earth resistance as required complete all as specified and directed. Note:- 7.5 RM strip wire upto 7.5 RM including unit rate.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc. as required of size 32 x 6mm galvanised iron strip

M&L for loose filling spreading and leveling hard core 40mm graded corse aggregate all as specified and directed.

M&L for surface excavation in soft/ loose soil not exceeding 30cm deep and averaging 15 cm and getting out including leveling the surface all as specified and directed.

M&L for Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for LT, 20 x 15cm size including taking down old one complete all as specified and directed.

M&L for Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for HT, 25 x 20 cm size including taking down old one complete all as specified and directed.

M&L for taking electric shutdown and employing labour competent to climb on trees for maintenance and trimming/ cutting of tree branches of any dia inside the electric installation around 2 pole/ 4 pole structure, Transformers, RMUs, etc upto the clearance of 2 mtr or all as directed all around and removing the garbage and deposting when and where directed complete all as specified and directed. Note:- Required labours with proper safety kit and cuttings tools, ledder, electric saw/ generator set,wire rope etc shall be provided by the contractor and rates are deemed to be included the quoted rates.

Swasti Electricals (BID ID -3484922)

MODI CORPORATION (BID ID -3489253)

Ms Kailash Chandra Babulal (BID ID -3492194)