CONSTRUCTION OF BARRACK ACCOMMODATION FOR SECURITY PERSONNELS AT ICP MOREH IN TENGNOUPAL DISTRICT IN THE STATE OF MANIPUR ON INDIA MYANMAR BORDER.

Amount

EARTHWORK

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(All kinds of soil.)

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 meters lift upto 1.5 metre.

Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

DAMP-PROOF COURSE

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement :2c/sand :4 graded stone aggregate 20mm nominal size )

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

RE-INFORCED CEMENT CONCRETE WORK

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level

All works above plinth level upto floor V level

All works above plinth level upto floor V level for column

STEEL REINFORCEMENT

Steel reinforcement for R.C.C work including straightening,cutting,bending, placing in position and binding all complete upto plinth level (Thermo-Mechanically Treated bars)

BRICKWORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

IN SUPERSTRUCTURE

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

HALF BRICK MASONRY

Half brick masonry with common burnt clay F.P.S.(non modular) brick of class designation 7.5 in super structure above plinth level up to floor V level.Cement mortar 1:4 (1 cement: 3 coarse sand)

Ground Floor walls

Floor-I walls

Floor-II walls

Parapet

FORMWORK

Providing formworks I/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

Foundation,footings,bases of columns,etc.for mass concrete.

Suspended floors,roofs,landing,balconies and access platform.

Lintels,beams,plinth beams,girders,bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

STEEL WORK

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

WOOD WORKS

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and ixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (35 mm thick shutters)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (30 mm thick shutters)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :250X10MM

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125mm

FLOORING

52 mm thick cement concrete flooring with concrete hardener topping,under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shade complete.

Marble stone flooring with 18 mm thick marble stone,as per sample of marble approved by Engineer-in-charge ,over 20mm(average)thick base of cement mortar 1:4(1 cement : 4 coarse sand) laid and jointed with grey cement slurry,including rubbing and polishing complete with : Udaipur Green Marble

Providing and laying Polished Granite stone flooring in required design and patterns,in linear as wall as curvilinear portion of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing,curing and polishing etc.all complete as specified and as directed by the engineer-in-charge.

FINISHING

12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion (i) Single socketed pipes.110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. (110 mm bend)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.(110 mm)

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

MISCELLANEOUS

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

FITTINGS

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

510x1040 mm bowl depth 225 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 1500x450 mm Mirror with Plastic moulded frame

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

DRAINAGE

NOTE : - The rates given for all the items under sub-head ‘ Drainage’ are applicable to work executed in soils above sub- soil water level. Extra allowance has to be made for work under sub- soil water level.

Soil pipes

Providing, laying and jointing glazed stoneware pipes class SP-1with stiff mixture of cement mortar in the proportion of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete

For 100mm pipes

Waste pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

75 mm nominal inner dia Pipes

Rain water pipes

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

For 100mm pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (NOTE: Concealed work, including cutting chases and making good the walls etc.)

25 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931

15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

circular Tank

Providing and fixing gun metal non- return valve of approved quality (screwed end)

40mm nominal bore horizontal

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5mm2+1 X 2.5 mm2 earth wire

2 X 4 mm2+1 X 4 mm2 earth wire

2 X 10 sq. mm + 1 X 10 sq. mm earth wire

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loopearthing as required.

S/F (following way) single/double pole and neutral, sheet steel MCB ditribution board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, phosphatized and power painted including earthing etc. as reqd. (but without MCB/RCCB/Isolator).

8 way double door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc. as reqd.

Single pole.

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd.

P/F 200 amp. TPN stand ground on land change over switch (Compact design) 415/500 V including connectionet as reqd.

S/F ( following rating ) four pole 415V isolator in the existing MCB DB complete with connection, testing and commissioning as reqd.

Providing and Fixing (following capacity TP & N) dis-connector fuse switch unit inside the existing cubical panel board with ISI mark HRC fuses including drilling holes in the cubicle panel board, making connection as reqd.

4. 200amp. TP & N

S/F 3 pin 5 amp ceiling rose on the existing junction box/wooden block i/c connection etc. as reqd.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

EARTHING

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal/ coke and salt ) as required.

FIXTURES/FITTINGS

S/F surface/Pendent mounting 12 W led bulb complete with driver i/c connection etc. as reqd.

S/F surface/Pendent mounting 15 W led Downlight complete with driver i/c connection etc. as reqd.

SITC of 1200mm sweep, BEE 5 star rated, ceiling fan with brushless direct current(BLDC) Motor, 30cm long down rod, 2 nos. canopies, shakle kit, safety rope, copper winding, Power factor.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

306 mm sweep

Description of Work / Item(s)

Amount

EARTHWORK

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(All kinds of soil.)

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 meters lift upto 1.5 metre.

Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

DAMP-PROOF COURSE

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement :2c/sand :4 graded stone aggregate 20mm nominal size )

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

DESIGN MIX CONCRETE

Providing and laying in position machine batched and machine mixed design mix M25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of cenetering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS:9103 to accelerate, retrd setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge.

All works above plinth level upto floor V level.

All works above plinth level upto floor V level-Columns

STEEL REINFORCEMENT

Steel reinforcement for R.C.C work including straightening,cutting,bending, placing in position and binding all complete upto plinth level (Thermo-Mechanically Treated bars)

BRICKWORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

IN SUPERSTRUCTURE

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

HALF BRICK MASONRY

Half brick masonry with common burnt clay F.P.S.(non modular) brick of class designation 7.5 in super structure above plinth level up to floor V level.Cement mortar 1:4 (1 cement: 3 coarse sand)

Ground Floor walls

Floor-I walls

Floor-II walls

Mumty walls

Parapet

FORMWORK

Providing formworks I/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

Foundation,footings,bases of columns,etc.for mass concrete.

Suspended floors,roofs,landing,balconies and access platform.

Lintels,beams,plinth beams,girders,bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stair,(excluding landing) except spiral-staircases.

STEEL WORK

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Steel work welded in built up sections/ framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required

In gratings , frames, guard bar, ladder, railings, brackets, gates and similar works

WOOD WORKS

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and ixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (35 mm thick shutters)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (30 mm thick shutters)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125mm

FLOORING

52 mm thick cement concrete flooring with concrete hardener topping,under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing anfd fixing 10mm thick acid and/or alkali resistant tiles of approved make and colour using acid and /or alkali resisting mortar bedding,and joints filled with acid and/or alkali resisting cement as per IS:4457,completeas per the direction of Engineer-in-Charge.In flooring on a bed of 10 mm thick mortar 1:4 ( 1 acid proof cement :4 coarse sand) Acid and alkali resistant tiles

FINISHING

12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion (i) Single socketed pipes.110 mm diameter

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.(110 mm)

CEMENT PAINTING - ORDINARY

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Applying priming coat:

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

ENAMEL PAINT

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

MISCELLANEOUS

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

GROUP C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5mm2+1 X 2.5 mm2 earth wire

2 X 4 mm2+1 X 4 mm2 earth wire

2 X 10 sq. mm + 1 X 10 sq. mm earth wire

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loopearthing as required.

S/F (following way) single/double pole and neutral, sheet steel MCB ditribution board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, phosphatized and power painted including earthing etc. as reqd. (but without MCB/RCCB/Isolator).

8 way double door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc. as reqd.

Single pole.

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd.

P/F 200 amp. TPN stand ground on land change over switch (Compact design) 415/500 V including connectionet as reqd.

S/F ( following rating ) four pole 415V isolator in the existing MCB DB complete with connection, testing and commissioning as reqd.

Providing and Fixing (following capacity TP & N) dis-connector fuse switch unit inside the existing cubical panel board with ISI mark HRC fuses including drilling holes in the cubicle panel board, making connection as reqd.

4. 200amp. TP & N

S/F 3 pin 5 amp ceiling rose on the existing junction box/wooden block i/c connection etc. as reqd.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

EARTHING

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal/ coke and salt ) as required.

FIXTURES/FITTINGS

S/F surface/Pendent mounting 12 W led bulb complete with driver i/c connection etc. as reqd.

S/F surface/Pendent mounting 15 W led Downlight complete with driver i/c connection etc. as reqd.

SITC of 1200mm sweep, BEE 5 star rated, ceiling fan with brushless direct current(BLDC) Motor, 30cm long down rod, 2 nos. canopies, shakle kit, safety rope, copper winding, Power factor.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

307 mm sweep

Description of Work / Item(s)

Amount

EARTHWORK

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(All kinds of soil.)

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 meters lift upto 1.5 metre.

Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

DAMP-PROOF COURSE

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement :2c/sand :4 graded stone aggregate 20mm nominal size )

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

RE-INFORCED CEMENT CONCRETE WORK

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level

All works above plinth level upto floor V level

All works above plinth level upto floor V level for column

STEEL REINFORCEMENT

Steel reinforcement for R.C.C work including straightening,cutting,bending, placing in position and binding all complete upto plinth level (Thermo-Mechanically Treated bars)

BRICKWORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

IN SUPERSTRUCTURE

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

HALF BRICK MASONRY

Half brick masonry with common burnt clay F.P.S.(non modular) brick of class designation 7.5 in super structure above plinth level up to floor V level.Cement mortar 1:4 (1 cement: 3 coarse sand)

Ground Floor walls

Floor-I walls

Floor-II walls

Mumty walls

Parapet

FORMWORK

Providing formworks I/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

Foundation,footings,bases of columns,etc.for mass concrete.

Suspended floors,roofs,landing,balconies and access platform.

Lintels,beams,plinth beams,girders,bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stair,(excluding landing) except spiral-staircases.

STEEL WORK

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

WOOD WORKS

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and ixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (35 mm thick shutters)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (30 mm thick shutters)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :250X10MM

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125mm

FLOORING

52 mm thick cement concrete flooring with concrete hardener topping,under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and Laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)with water absorption's less than 0.08% and conforming to IS:15622 of approved make in all colours and shades,laid on on 20mm thick cement mortar 1:4(1cement:4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints wiyh white cement and matching pigments etc.,complete.Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Marble stone flooring with 18 mm thick marble stone,as per sample of marble approved by Engineer-in-charge ,over 20mm(average)thick base of cement mortar 1:4(1 cement : 4 coarse sand) laid and jointed with grey cement slurry,including rubbing and polishing complete with : Udaipur Green Marble

Extra for marble stone flooring in treads of steps and risers using singie length up to 2.00 meter.

Providing and laying Polished Granite stone flooring in required design and patterns,in linear as wall as curvilinear portion of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing,curing and polishing etc.all complete as specified and as directed by the engineer-in-charge.

Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard,jointed with neat cement slurry mixed with pigment to match the shade of tiles,including rubbing and cleaning etc.complete,on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand)Medium shade pigment using 50% white cement 50% Grey cement

Providing anfd fixing 10mm thick acid and/or alkali resistant tiles of approved make and colour using acid and /or alkali resisting mortar bedding,and joints filled with acid and/or alkali resisting cement as per IS:4457,completeas per the direction of Engineer-in-Charge.In flooring on a bed of 10 mm thick mortar 1:4 ( 1 acid proof cement :4 coarse sand) Acid and alkali resistant tiles

In dado/skirting on 12 mm thick mortar 1:4 ( 1 acid proof cement :4 coarse sand) Acid and alkali resistant tiles

FINISHING

12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion (i) Single socketed pipes.110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. (110 mm bend)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.(110 mm)

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

MISCELLANEOUS

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Description of Work / Item(s)

Amount

EARTHWORK

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(All kinds of soil.)

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 meters lift upto 1.5 metre.

Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

DAMP-PROOF COURSE

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement :2c/sand :4 graded stone aggregate 20mm nominal size )

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

RE-INFORCED CEMENT CONCRETE WORK

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level

All works above plinth level upto floor V level

All works above plinth level upto floor V level for column

STEEL REINFORCEMENT

Steel reinforcement for R.C.C work including straightening,cutting,bending, placing in position and binding all complete upto plinth level (Thermo-Mechanically Treated bars)

BRICKWORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

IN SUPERSTRUCTURE

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

HALF BRICK MASONRY

Half brick masonry with common burnt clay F.P.S.(non modular) brick of class designation 7.5 in super structure above plinth level up to floor V level.Cement mortar 1:4 (1 cement: 3 coarse sand)

Ground Floor walls

Floor-I walls

Mumty walls

Parapet

FORMWORK

Providing formworks I/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

Foundation,footings,bases of columns,etc.for mass concrete.

Suspended floors,roofs,landing,balconies and access platform.

Lintels,beams,plinth beams,girders,bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stair,(excluding landing) except spiral-staircases.

STEEL WORK

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

WOOD WORKS

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and ixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (35 mm thick shutters)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (30 mm thick shutters)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :250X10MM

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125mm

FLOORING

52 mm thick cement concrete flooring with concrete hardener topping,under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and Laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)with water absorption's less than 0.08% and conforming to IS:15622 of approved make in all colours and shades,laid on on 20mm thick cement mortar 1:4(1cement:4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints wiyh white cement and matching pigments etc.,complete.Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shade complete.

Marble stone flooring with 18 mm thick marble stone,as per sample of marble approved by Engineer-in-charge ,over 20mm(average)thick base of cement mortar 1:4(1 cement : 4 coarse sand) laid and jointed with grey cement slurry,including rubbing and polishing complete with : Udaipur Green Marble

Extra for marble stone flooring in treads of steps and risers using singie length up to 2.00 meter.

Providing and laying Polished Granite stone flooring in required design and patterns,in linear as wall as curvilinear portion of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing,curing and polishing etc.all complete as specified and as directed by the engineer-in-charge.

Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard,jointed with neat cement slurry mixed with pigment to match the shade of tiles,including rubbing and cleaning etc.complete,on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand)Medium shade pigment using 50% white cement 50% Grey cement

Providing anfd fixing 10mm thick acid and/or alkali resistant tiles of approved make and colour using acid and /or alkali resisting mortar bedding,and joints filled with acid and/or alkali resisting cement as per IS:4457,completeas per the direction of Engineer-in-Charge.In flooring on a bed of 10 mm thick mortar 1:4 ( 1 acid proof cement :4 coarse sand) Acid and alkali resistant tiles

In dado/skirting on 12 mm thick mortar 1:4 ( 1 acid proof cement :4 coarse sand) Acid and alkali resistant tiles

FINISHING

12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion (i) Single socketed pipes.110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. (110 mm bend)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.(110 mm)

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

MISCELLANEOUS

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

510x1040 mm bowl depth 225 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 1500x450 mm Mirror with Plastic moulded frame

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

DRAINAGE

NOTE : - The rates given for all the items under sub-head ‘ Drainage’ are applicable to work executed in soils above sub- soil water level. Extra allowance has to be made for work under sub- soil water level.

Soil pipes

Providing, laying and jointing glazed stoneware pipes class SP-1with stiff mixture of cement mortar in the proportion of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete

For 100mm pipes

Waste pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

75 mm nominal inner dia Pipes

Rain water pipes

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

For 100mm pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (NOTE: Concealed work, including cutting chases and making good the walls etc.)

25 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931

15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

circular Tank

Providing and fixing gun metal non- return valve of approved quality (screwed end)

40mm nominal bore horizontal

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

GROUP C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5mm2+1 X 2.5 mm2 earth wire

2 X 4 mm2+1 X 4 mm2 earth wire

2 X 10 sq. mm + 1 X 10 sq. mm earth wire

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loopearthing as required.

S/F (following way) single/double pole and neutral, sheet steel MCB ditribution board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, phosphatized and power painted including earthing etc. as reqd. (but without MCB/RCCB/Isolator).

8 way double door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc. as reqd.

Single pole.

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd.

P/F 200 amp. TPN stand ground on land change over switch (Compact design) 415/500 V including connectionet as reqd.

S/F ( following rating ) four pole 415V isolator in the existing MCB DB complete with connection, testing and commissioning as reqd.

Providing and Fixing (following capacity TP & N) dis-connector fuse switch unit inside the existing cubical panel board with ISI mark HRC fuses including drilling holes in the cubicle panel board, making connection as reqd.

4. 200amp. TP & N

S/F 3 pin 5 amp ceiling rose on the existing junction box/wooden block i/c connection etc. as reqd.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

EARTHING

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal/ coke and salt ) as required.

FIXTURES/FITTINGS

S/F surface/Pendent mounting 12 W led bulb complete with driver i/c connection etc. as reqd.

S/F surface/Pendent mounting 15 W led Downlight complete with driver i/c connection etc. as reqd.

SITC of 1200mm sweep, BEE 5 star rated, ceiling fan with brushless direct current(BLDC) Motor, 30cm long down rod, 2 nos. canopies, shakle kit, safety rope, copper winding, Power factor.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

305mm sweep

S/F 1.5 tone capacity split type Air conditioner, (Diamond, 3 Star, 5G 29, G-SC 18FD3 WJH) complete.

Description of Work / Item(s)

Amount

EARTHWORK

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(All kinds of soil.)

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 meters lift upto 1.5 metre.

Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

DAMP-PROOF COURSE

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement :2c/sand :4 graded stone aggregate 20mm nominal size )

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

RE-INFORCED CEMENT CONCRETE WORK

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level

All works above plinth level upto floor V level

All works above plinth level upto floor V level for column

STEEL REINFORCEMENT

Steel reinforcement for R.C.C work including straightening,cutting,bending, placing in position and binding all complete upto plinth level (Thermo-Mechanically Treated bars)

BRICKWORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

IN SUPERSTRUCTURE

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

HALF BRICK MASONRY

Half brick masonry with common burnt clay F.P.S.(non modular) brick of class designation 7.5 in super structure above plinth level up to floor V level.Cement mortar 1:4 (1 cement: 3 coarse sand)

Ground Floor walls

Floor-I walls

Mumty walls

Parapet

FORMWORK

Providing formworks I/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

Foundation,footings,bases of columns,etc.for mass concrete.

Suspended floors,roofs,landing,balconies and access platform.

Lintels,beams,plinth beams,girders,bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stair,(excluding landing) except spiral-staircases.

STEEL WORK

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

WOOD WORKS

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and ixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (35 mm thick shutters)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (30 mm thick shutters)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :250X10MM

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125mm

FLOORING

52 mm thick cement concrete flooring with concrete hardener topping,under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and Laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)with water absorption's less than 0.08% and conforming to IS:15622 of approved make in all colours and shades,laid on on 20mm thick cement mortar 1:4(1cement:4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints wiyh white cement and matching pigments etc.,complete.Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shade complete.

Marble stone flooring with 18 mm thick marble stone,as per sample of marble approved by Engineer-in-charge ,over 20mm(average)thick base of cement mortar 1:4(1 cement : 4 coarse sand) laid and jointed with grey cement slurry,including rubbing and polishing complete with : Udaipur Green Marble

Extra for marble stone flooring in treads of steps and risers using singie length up to 2.00 meter.

Providing and laying Polished Granite stone flooring in required design and patterns,in linear as wall as curvilinear portion of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing,curing and polishing etc.all complete as specified and as directed by the engineer-in-charge.

Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard,jointed with neat cement slurry mixed with pigment to match the shade of tiles,including rubbing and cleaning etc.complete,on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand)Medium shade pigment using 50% white cement 50% Grey cement

Providing anfd fixing 10mm thick acid and/or alkali resistant tiles of approved make and colour using acid and /or alkali resisting mortar bedding,and joints filled with acid and/or alkali resisting cement as per IS:4457,completeas per the direction of Engineer-in-Charge.In flooring on a bed of 10 mm thick mortar 1:4 ( 1 acid proof cement :4 coarse sand) Acid and alkali resistant tiles

In dado/skirting on 12 mm thick mortar 1:4 ( 1 acid proof cement :4 coarse sand) Acid and alkali resistant tiles

FINISHING

12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion (i) Single socketed pipes.110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. (110 mm bend)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.(110 mm)

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

MISCELLANEOUS

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

FITTINGS

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

510x1040 mm bowl depth 225 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 1500x450 mm Mirror with Plastic moulded frame

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

DRAINAGE

NOTE : - The rates given for all the items under sub-head ‘ Drainage’ are applicable to work executed in soils above sub- soil water level. Extra allowance has to be made for work under sub- soil water level.

Soil pipes

Providing, laying and jointing glazed stoneware pipes class SP-1with stiff mixture of cement mortar in the proportion of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete

For 100mm pipes

Waste pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

75 mm nominal inner dia Pipes

Rain water pipes

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

For 100mm pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (NOTE: Concealed work, including cutting chases and making good the walls etc.)

25 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931

15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

circular Tank

Providing and fixing gun metal non- return valve of approved quality (screwed end)

40mm nominal bore horizontal

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

GROUP C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5mm2+1 X 2.5 mm2 earth wire

2 X 4 mm2+1 X 4 mm2 earth wire

2 X 10 sq. mm + 1 X 10 sq. mm earth wire

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loopearthing as required.

S/F (following way) single/double pole and neutral, sheet steel MCB ditribution board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, phosphatized and power painted including earthing etc. as reqd. (but without MCB/RCCB/Isolator).

8 way double door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc. as reqd.

Single pole.

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd.

P/F 200 amp. TPN stand ground on land change over switch (Compact design) 415/500 V including connectionet as reqd.

S/F ( following rating ) four pole 415V isolator in the existing MCB DB complete with connection, testing and commissioning as reqd.

Providing and Fixing (following capacity TP & N) dis-connector fuse switch unit inside the existing cubical panel board with ISI mark HRC fuses including drilling holes in the cubicle panel board, making connection as reqd.

4. 200amp. TP & N

S/F 3 pin 5 amp ceiling rose on the existing junction box/wooden block i/c connection etc. as reqd.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

EARTHING

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal/ coke and salt ) as required.

FIXTURES/FITTINGS

S/F surface/Pendent mounting 12 W led bulb complete with driver i/c connection etc. as reqd.

S/F surface/Pendent mounting 15 W led Downlight complete with driver i/c connection etc. as reqd.

SITC of 1200mm sweep, BEE 5 star rated, ceiling fan with brushless direct current(BLDC) Motor, 30cm long down rod, 2 nos. canopies, shakle kit, safety rope, copper winding, Power factor.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

305mm sweep

S/F 1.5 tone capacity split type Air conditioner, (Diamond, 3 Star, 5G 29, G-SC 18FD3 WJH) complete.

Description of Work / Item(s)

Amount

EARTHWORK

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(All kinds of soil.)

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 meters lift upto 1.5 metre.

Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

DAMP-PROOF COURSE

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement :2c/sand :4 graded stone aggregate 20mm nominal size )

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

RE-INFORCED CEMENT CONCRETE WORK

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level

All works above plinth level upto floor V level

All works above plinth level upto floor V level for column

STEEL REINFORCEMENT

Steel reinforcement for R.C.C work including straightening,cutting,bending, placing in position and binding all complete upto plinth level (Thermo-Mechanically Treated bars)

BRICKWORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

IN SUPERSTRUCTURE

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

HALF BRICK MASONRY

Half brick masonry with common burnt clay F.P.S.(non modular) brick of class designation 7.5 in super structure above plinth level up to floor V level.Cement mortar 1:4 (1 cement: 3 coarse sand)

Ground Floor walls

Floor-I walls

Mumty walls

Parapet

FORMWORK

Providing formworks I/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

Foundation,footings,bases of columns,etc.for mass concrete.

Suspended floors,roofs,landing,balconies and access platform.

Lintels,beams,plinth beams,girders,bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stair,(excluding landing) except spiral-staircases.

STEEL WORK

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

WOOD WORKS

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and ixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (35 mm thick shutters)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (30 mm thick shutters)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :250X10MM

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125mm

FLOORING

52 mm thick cement concrete flooring with concrete hardener topping,under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and Laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)with water absorption's less than 0.08% and conforming to IS:15622 of approved make in all colours and shades,laid on on 20mm thick cement mortar 1:4(1cement:4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints wiyh white cement and matching pigments etc.,complete.Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shade complete.

Marble stone flooring with 18 mm thick marble stone,as per sample of marble approved by Engineer-in-charge ,over 20mm(average)thick base of cement mortar 1:4(1 cement : 4 coarse sand) laid and jointed with grey cement slurry,including rubbing and polishing complete with : Udaipur Green Marble

Extra for marble stone flooring in treads of steps and risers using singie length up to 2.00 meter.

Providing and laying Polished Granite stone flooring in required design and patterns,in linear as wall as curvilinear portion of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing,curing and polishing etc.all complete as specified and as directed by the engineer-in-charge.

Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard,jointed with neat cement slurry mixed with pigment to match the shade of tiles,including rubbing and cleaning etc.complete,on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand)Medium shade pigment using 50% white cement 50% Grey cement

Providing anfd fixing 10mm thick acid and/or alkali resistant tiles of approved make and colour using acid and /or alkali resisting mortar bedding,and joints filled with acid and/or alkali resisting cement as per IS:4457,completeas per the direction of Engineer-in-Charge.In flooring on a bed of 10 mm thick mortar 1:4 ( 1 acid proof cement :4 coarse sand) Acid and alkali resistant tiles

In dado/skirting on 12 mm thick mortar 1:4 ( 1 acid proof cement :4 coarse sand) Acid and alkali resistant tiles

FINISHING

12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion (i) Single socketed pipes.110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. (110 mm bend)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.(110 mm)

CEMENT PAINTING - ORDINARY

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Applying priming coat:

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

ENAMEL PAINT

Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

MISCELLANEOUS

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

FITTINGS

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

510x1040 mm bowl depth 225 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 1500x450 mm Mirror with Plastic moulded frame

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

DRAINAGE

NOTE : - The rates given for all the items under sub-head ‘ Drainage’ are applicable to work executed in soils above sub- soil water level. Extra allowance has to be made for work under sub- soil water level.

Soil pipes

Providing, laying and jointing glazed stoneware pipes class SP-1with stiff mixture of cement mortar in the proportion of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete

For 100mm pipes

Waste pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

75 mm nominal inner dia Pipes

Rain water pipes

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

For 100mm pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (NOTE: Concealed work, including cutting chases and making good the walls etc.)

25 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931

15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

circular Tank

Providing and fixing gun metal non- return valve of approved quality (screwed end)

40mm nominal bore horizontal

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

GROUP C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5mm2+1 X 2.5 mm2 earth wire

2 X 4 mm2+1 X 4 mm2 earth wire

2 X 10 sq. mm + 1 X 10 sq. mm earth wire

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loopearthing as required.

S/F (following way) single/double pole and neutral, sheet steel MCB ditribution board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, phosphatized and power painted including earthing etc. as reqd. (but without MCB/RCCB/Isolator).

8 way double door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc. as reqd.

Single pole.

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd.

P/F 200 amp. TPN stand ground on land change over switch (Compact design) 415/500 V including connectionet as reqd.

S/F ( following rating ) four pole 415V isolator in the existing MCB DB complete with connection, testing and commissioning as reqd.

Providing and Fixing (following capacity TP & N) dis-connector fuse switch unit inside the existing cubical panel board with ISI mark HRC fuses including drilling holes in the cubicle panel board, making connection as reqd.

4. 200amp. TP & N

S/F 3 pin 5 amp ceiling rose on the existing junction box/wooden block i/c connection etc. as reqd.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

EARTHING

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal/ coke and salt ) as required.

FIXTURES/FITTINGS

S/F surface/Pendent mounting 12 W led bulb complete with driver i/c connection etc. as reqd.

S/F surface/Pendent mounting 15 W led Downlight complete with driver i/c connection etc. as reqd.

SITC of 1200mm sweep, BEE 5 star rated, ceiling fan with brushless direct current(BLDC) Motor, 30cm long down rod, 2 nos. canopies, shakle kit, safety rope, copper winding, Power factor.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 305mm sweep

Description of Work / Item(s)

Amount

EARTHWORK

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(All kinds of soil.)

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 meters lift upto 1.5 metre.

Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

DAMP-PROOF COURSE

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement :2c/sand :4 graded stone aggregate 20mm nominal size )

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

RE-INFORCED CEMENT CONCRETE WORK

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level

All works above plinth level upto floor V level

All works above plinth level upto floor V level for column

STEEL REINFORCEMENT

Steel reinforcement for R.C.C work including straightening,cutting,bending, placing in position and binding all complete upto plinth level (Thermo-Mechanically Treated bars)

BRICKWORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

IN SUPERSTRUCTURE

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

HALF BRICK MASONRY

Half brick masonry with common burnt clay F.P.S.(non modular) brick of class designation 7.5 in super structure above plinth level up to floor V level.Cement mortar 1:4 (1 cement: 3 coarse sand)

Ground Floor walls

FORMWORK

Providing formworks I/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

(a) Foundation, footing, bases of columns etc. and mass concrete

(b) Flat surface such as suspended floors,roofs,landing and the like

(g)(i) Columns, pillars, posts and struts (square,rectangular or polygon in plan )

(h)(i) Sides and soffits of beams, beam haunchings, cantilivers, girders, bressumers and lintels not exceeding 1m in depth.

STEEL WORK

Steel work welded in built up sections/ framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required Steel work welded in built up sections/ framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required

Providing & fixing M.S. fan clamp type I of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying i/c painting the exposed portion of loops, all per standard design complete

Providing and fixing in position collapsible steel shutters with vertical channels 20mm x 10mm x 2mm & braced with flat iron diagonals 20mm x 5mm sizes with top & bottom rails of T iron 40mm x 40mm x 6mm with 38mm dia steel pulleys complete with bolts & nuts locking arrangement, stoppers, handles i/c applying a priming coat of red lead paint.

WOOD AND PVC WORKS

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and ixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (35 mm thick shutters)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood (30 mm thick shutters)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :250X10MM

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125mm

FLOORING

52 mm thick cement concrete flooring with concrete hardener topping,under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and laying Polished Granite stone flooring in required design and patterns,in linear as wall as curvilinear portion of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing,curing and polishing etc.all complete as specified and as directed by the engineer-in-charge.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

FINISHING

12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion (i) Single socketed pipes.110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. (110 mm bend)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.(110 mm)

CEMENT PAINTING - ORDINARY

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

ENAMEL PAINT

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

PLASTIC EMULSION PAINT

Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

MISCELLANEOUS

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

GROUP C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5mm2+1 X 2.5 mm2 earth wire

2 X 4 mm2+1 X 4 mm2 earth wire

2 X 10 sq. mm + 1 X 10 sq. mm earth wire

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loopearthing as required.

S/F (following way) single/double pole and neutral, sheet steel MCB ditribution board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, phosphatized and power painted including earthing etc. as reqd. (but without MCB/RCCB/Isolator).

8 way double door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc. as reqd.

Single pole.

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd.

P/F 200 amp. TPN stand ground on land change over switch (Compact design) 415/500 V including connectionet as reqd.

S/F 3 pin 5 amp ceiling rose on the existing junction box/wooden block i/c connection etc. as reqd.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

EARTHING

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal/ coke and salt ) as required.

FIXTURES/FITTINGS

S/F surface/Pendent mounting 12 W led bulb complete with driver i/c connection etc. as reqd.

S/F surface/Pendent mounting 15 W led Downlight complete with driver i/c connection etc. as reqd.

SITC of 1200mm sweep, BEE 5 star rated, ceiling fan with brushless direct current(BLDC) Motor, 30cm long down rod, 2 nos. canopies, shakle kit, safety rope, copper winding, Power factor.

Description of Work / Item(s)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

All kinds of soil

Earth work in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and lift upto 1.5 m :

All kinds of soil

Description of Work / Item(s)

Amount

JAWAN BARRACK- 1

JAWAN BARRACK- 2.

JAWAN BARRACK- 3.

MAHILLA BARRACK.

OFFICER BARRACK.

SUBORDINATE OFFICERS'ACCOMODATION.

SECURITY GATE

SITE DEVELOPMENT

SOLAR STREET LAMP

RK FORTUNE DEVELOPERS PVT. LTD.

OINAM OKEN SINGH

RK FORTUNE DEVELOPERS PVT. LTD.

OINAM OKEN SINGH

RK FORTUNE DEVELOPERS PVT. LTD.

OINAM OKEN SINGH

RK FORTUNE DEVELOPERS PVT. LTD.

OINAM OKEN SINGH

RK FORTUNE DEVELOPERS PVT. LTD.

OINAM OKEN SINGH

RK FORTUNE DEVELOPERS PVT. LTD.

OINAM OKEN SINGH

RK FORTUNE DEVELOPERS PVT. LTD.

OINAM OKEN SINGH

RK FORTUNE DEVELOPERS PVT. LTD.

OINAM OKEN SINGH

RK FORTUNE DEVELOPERS PVT. LTD.

OINAM OKEN SINGH