C/o Forest Rest House at Carignano in Shimla Forest Division

Amount

Cutting in earth work in all kinds of soil such as pick, jumper, blasting/chiselling/wedging out hard/soft rock and disposal for excavated earth in all leads and lifts as per the direction of Engineer-in-Charge and stacking of useful stones to specified dimension.pick/ jumper works.

Excavation in foundations, trenches etc., in earth work, in all kinds of soil such as pick work, jumper work, blasting/chiseling/wedging out of soft/hard rock including pumping and bailing out water and stacking the excavated as per direction, from the edge of the excavation and then returning the stacked soil in 15 cm. layers, foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth in all leads and lifts manually and mechanically means as directed by the Engineer-in-Charge.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5 mm so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies for all height of propping and centering below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work including carriage of materials in all leads and lifts. in Foundation footing base of columns and the like and mass concrete

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5 mm so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies for all height of propping and centering below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work including carriage of materials in all leads and lifts. in Flat surfaces such as soffits and suspended floor, roofs and like plain upto 200 mm in thickness.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5 mm so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies for all height of propping and centering below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work including carriage of materials in all leads and lifts. in Coloumn, pillars, posts and struts upto floor two level

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5 mm so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies for all height of propping and centering below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work including carriage of materials in all leads and lifts. in Beams, cantilever, girders and lintel:- Side of soffits of beam, beams hunching cantilevers bressumbers and not exceeding 1 meter in depth in all heights from floor.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5 mm so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies for all height of propping and centering below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work including carriage of materials in all leads and lifts. in Stair case with sloping stepped soffits including landing.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5 mm so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies for all height of propping and centering below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work including carriage of materials in all leads and lifts. in Edges of slabs and breaks in floors and walls above 20 cm wide.

Providing and laying cement concrete 1:6:12 (1cement:6sand:12graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinths including carriage of materials in all leads and lifts.

Providing and laying cement concrete 1:4:8 (1cement: 4sand: 8graded stone aggregate 25 mm nominal size) through mechanical means and curing complete excluding cost of form work foundation and plinths in breast and retaining walls including carriage of materials in all lead and lifts.Under RCC coulmns.

Providing and laying cement concrete 1: 1/1.5 :3(1cement: 1/1.5sand: 3graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials in all leads and lifts upto all heights.. in Foundation, footings, basis of columns and mass concrete.

Providing and laying cement concrete 1: 1/1.5 :3(1cement: 1/1.5sand: 3graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials in all leads and lifts upto all heights.. in Suspended floors, roofs, landings, shelves and their supports balconies beams, girders bressumers and cantilevers for all floor levels in all leads and lifts.

Providing and laying cement concrete 1: 1/1.5 :3(1cement: 1/1.5sand: 3graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials in all leads and lifts upto all heights.. in columns, pillars, posts and struts for all floor levels in all leads and lifts.

Providing and laying cement concrete 1: 1/1.5 :3(1cement: 1/1.5sand: 3graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials in all leads and lifts upto all heights.. in Stair cases (except spiral stair cases) excluding landing but including preparing of surface and finishing the nosing upto all floor level.

Providing mild steel/tor steel reinforcement for RCC work including bending, binding also cost of binding wire and placing in position complete upto all floor level including carriage of materialss in all lead and lifts. In Tor steel

Providing and laying 20 cm. thick composit stone masonry with stone facing of chisel dressed stones one line dressed in cement mortar 1:6(1 cement :6 sand) and concrete backing with cement concrete 1:3:6 (1 cement: 3 sand: 6 graded stone aggregate 20 mm. nominal size) on inner face of walls including centring,shuttering and propping complete up to floor two level.

Half brick masonry in common burnt clay building bricks 2nd class in superstructure upto all heights in cement mortar 1:4 (1cement:4sand) including carriage of materials in all leads and lifts. Less openings

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1cement:6sand:12 graded stone aggregate 20 mm nominal size) at plinth level in cement mortar 1:6 (1 cement:6sand) including carriage of materials in all leads, lifts and upto all height in breast and retaining walls. in Under dormitory block

Providing wood work in frames of doors, windows and other frames wrought framed and fixed in position in 1st Class Deodar wood including carriage of materials in all lead and lifts.

Providing wood work in frames of false celling partitions etc. sawn and put-up in sizes including carriage of materials in all leads and lifts position.2nd Class Deodar Wood. Caretaker in Wall linning in Dining hall / longe (7.51x6.11 Mtr.) & family suite (7.52X4.22 M)

Providing and fixing plain particle board ceiling of approved quality with butt jointing and nails upto all heights(frame work cover fillets to be paid for separately) including carriage of materials within all leads and lifts. In dormitory/ caretaker

Providing and fixing panelled glazed or paneled and glazed shutters for doors windows and clerestory windows including black enameled iron butt hinges with necessary screws and wooden moulding beading also carriage of materialss in all leads and lifts 40 mm thick 2nd class deodar wood & less 40% for frame area and fixed glass

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of I.S. gauge designation 85G with wire of dia 0.56 mm for doors, windows and clerestory enameled iron hinges with necessary screws including carriage of materials in all leads and lifts. 40 mm thick Ist class deodar wood.

Providing and fixing water proof kit ply of standard quality ISI mark and approved shade and colour in panelling & wall linning i/c mitring at junctions, butt jointing and nails complete (Frame work for base to be measured & paid for separately) 9mm thick Wall linning in Dining hall / longe (7.51x6.11 Mtr.) & family suite (7.52X4.22 M.)

Providing and fixing plain lining with tongued and groved jointing and screws (frame work and cover fillets to be measured and paid for separately with. 1st class deodar wood. 20mm thick Wall linning in Dining hall / longe (7.51x6.11 Mtr.)

Providing and fixing plain lining with tongued and groved jointing and screws (frame work and cover fillets to be measured and paid for separately with. 2nd class deodar wood. 20mm thick II nd class deodar wood. 20mm thick in Add 25% for slope and darmer windows of main roofing area

Providing and Fixing Glass panes with denter's metal putty/wooden fillet (where ever required) of deodar Ist class in fixed portions of windows:- a) Plate glass 5.5 mm thick

Providing and Fixing Glass panes with denter's metal putty/wooden fillet (where ever required) of deodar Ist class in fixed portions of windows:- (b)12mm Toughned Glass formain entrance door

Providing and fixing flush door shutters decorative type core of block board construction with frames of first class hard wood and well matched first class commercial ply veneering with vertical grains or cross bands and face veneering on one face bend and commercial ply veneering with vertical grains of cross band and face veneer on other face of shutter, including carriage of materials in all leads and lifts and moulding required in the shutter in 40 mm thick including black enameled M.S. butt hinges in toilet doors

Providing and fixing 40x3 mm flat iron hold fast 40 Cm. long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm 1:3:6 (1cement:3sand:6graded stone aggregate of 20 mm nominal size in all the doors/windows

Providing and fixing 75x60 mm rounded hand rail in straight length complete in Ist class deodar wood complete including carriage of materials in all lead and lifts.

Providing and fixing 75 mm x 60 mm caps turned to match the hand rails and matred in including hand rails screws and dowls (dia of cap to be twice the width of hand rails) 1st class deodar wood including carriage of materials in all leads and lifts

Providing and fixing bright finished brass sliding door-bolts with nuts and screws etc. complete including carriage of materials in all leads and lifts (250x16 mm)

Providing fixing bright finished brass tower bolts (barrel type) with screws etc. complete complete including carriage of materials in all leads and lifts. (200 mm x 10 mm)

Providing fixing bright finished brass tower bolts (barrel type) with screws etc. complete complete including carriage of materials in all leads and lifts. (150 x 10 mm toilet)

Providing and fixing bright finished brass handle as per sample approvedwith screws etc. complete including carriage of materials in all leads and lifts. (100 mm in windows)

Providing and fixing bright finished brass handle as per sample approvedwith screws etc. complete including carriage of materials in all leads and lifts. (125 mm in doors)

Providing and fixing 100 mm bright finished brass door stopper.

Providing and fixing bright banished brass 100 mm mortice latch and lock and a pair of handles with necessary screws (Indian make) of standard makewith a pair of key including carriage of materials in all leads ana lifts.

Providing and fixing bright finished brass casement stays (straight peg type) with necessary screws etc. complete including carriage of materials in all leads and lifts (a) 250 mm in Windows

25mm thick Kota stone slab flooring on base of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbbing and kota polishing complete, including carriage of materials in all leads, lifts and heights, in : (GROUND FLOOR)

25 mm thick kota stone slab in risers of steps, skirting dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1cement:3sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete including Carriage of materials in all leads & lifts.

Providing and fixing 10 mm thick anti skid water proof stain and impact resistant heavy duty vitrified tiles Kazaria or equivalent 600x600x10 mm of approved shade and quality in floors laid over 12 mm thick cement mortar 1:3 (1cement:3sand) jointed with cement slurry mixed with pigment as required complete.

Providing and fixing spartic Ceramic tiles 6 mm to 8 mm thick of Nitco or equivalent flooring, 300x300 mm size laid on a bed of 12 mm thick cement mortar 1:3 jointing with cement mixed with pigment to match the shade of tiles including carriage of materials in all leads, lifts and heights.

Providing and fixing Coloured glazed tiles Nitco /Kajaria make in skirting, risers of steps and dado laid over 12 mm thick cement mortar 1:3 (1cement:3sand) and jointed with cement slurry upto all floor including carriage of materials in all lead lifts, height and all floor level.

Providing and laying granite stone in flooring 20mm(average)thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. 20mm.thick including carriage of materials in all lead and lifts and heights.

Slate roofing with 7.5 cm lap double layer fixed on wooden battens (wood work to be paid for separately) With slates 40x20 cm size.

Providing and fixing ridges or hips 60 cm overall with 0.60 mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charges including carriage of materials in all lead, lift and height (Tata/Century wells make).

Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third & fifth courses of blown or resideual bitumen applied at 1.45 kg 1.20 and 1.45 kg persq.mof area respectively second and fourth course of roofing felt type 3 grade i (hessain bese finished bitumen felt ) sixth and final course of stone girt 6 mm and down size or pea sized gravel spread at 6 cu.dm or (0.006 cu.m) per sq.m including preparation of surface excluding grading complete

Providing and laying plastic roofing compound standrad black (using 2.75 kg per sq m) over a surface painted with cold plastic roofing liquid compound at 0.24 litre per sq.m including spreading sand over the top surface at 6 cu dm. or (0.006 cu.m) per sq.m etc complete. Below Slate Roofing.

Providing and fixing flashing 38 cm overall with 0.60 mm thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia meter & prepainted G.I. limpet & bitumen washer completed with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials in all lead, lift and height (Tata/Century wells make).

Providing and fixing 0.60 mm prepainted sheet gutter 15 cm wide 45 cm over all forming box with nut and bolts and washers etc. including making necessary connection and all lead, lifts and carriage of materials. (Tata/Century wells make).

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete. including carriage of materials in all lead lifts and heights.(100 mm dia)

Providing and fixing PVC holder bat clamps heavy duty of approved design to PVC pipes embedded in and including cement concrete block 10x10x10 cm of 1:2:4 (1cement: 2sand: 4graded stone agreement 20 mm nominal size) and cost of cutting holes and making good the wall etc. including carriage of materials in all lead lifts and heights (a) 100 mm dia meter.

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete

Steel work welded in built up sections trusses and framed work including cutting hoisting fixing in position and applying a priming coat of red lead paints. a) In trusses and trussed purlins in building

Steel work welded in built up sections trusses and framed work including cutting hoisting fixing in position and applying a priming coat of red lead paints. b) In gratings framed guard bars ladders, railings brackets and similar works

Providing and fixing oxidized M.S. single acting spring hings 125 mm with necessary screws etc. complete including carriage of materials in all leads and lifts.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint to give an even shade including cleaning the surface of all dirt, dust and other foreign matter.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand, papering and knotting including carriage of materials in all lead and lifts.:

Painting two coats (excluding priming coat) on new wood and wood based surfaces, with readymixed paint, brushing to give an even shade including cleaning of all dirt, dust and other foreign matter sand papering and stopping.

Extra coat over every subsiquent coat of paint.

Polishing two coats with french polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler including carriage materials in all lead and lifts. in Stair hand rail

Extra coat over every subsiquent coat of polishing.

Applying priming coat on new concrete/masonry/ asbestos cement/ plastered surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required with ready mix premier including carriage of materials in all leads and lifts and heights.

6 mm thick cement plaster to ceiling in cement mortar 1:3 (1cement:3sand) including carriage of materials in all leads and lifts and heights.

15 mm cement plaster in single coat on rough/fair side of brick/concrete/stone wall for exterior plastering in all floor level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1cement:6sand) including carriage of materials in all leads and lifts and heights and cost of scafolding.

20 mm cement plaster in single coat on fair/ rough side of brick/cement wall for interior plastering including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:5 (1cement:5sand) upto all heights including carriage of materials in all leads, lifts and heights.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Wall Painting ( two coats) with plastic emulsion paint of approved brand and manufacture on decorated wall surface to give an even shade including thoroughly brushing the surface clean of all dirt grease loose pieces of scale and sand papered smooth including applying of putty a required for making the surface including carriage of materials in all lead and lifts..

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1cement:3sand:6 graded stone).

Providing and filling cinder in the sunken portion of toilets to the required level of toilet including watering ramming and carriage of material in all leads and lifts.

Providing Water proofing treatment in all sunken portions, ceilings and walls or floors(wherever required) by applying two coats of Pidifine (2K) (Pidilite make) by first scraping the old paints on walls (wherever required) and cleaning with the wire brush to remove all foreign particles and paintings etc. Making the surface wet and then 10 mm thk. plastering in C.M 1:4, (1Cement:4 sand) curing etc. comp. with necessary scaffolding and testing wherever required including carriage of materials with all leads and lifts :

Making Moulding/nosing work with machine for Kota stone/ Marble/ Granite stones in steps/worktops etc where required etc. at all floors/heights.

Providing under layer for plinth protection of 75 mm thick consolidated (bed dry brick/stone aggregate 40 mm nominal) well rammed and consolidated and grouted with fine sane including preparation of ground including carriage of materials in all lead and lifts.

Constructing course rubble hammer dressed “U” shape open surface drain with side wall 15x22 cm in cement mortar 1:6 (1cement:6sand) and inside plastering with cement plaster 1:3 (1cement:3sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1cement:5sand:10 graded stone aggregate) of 40 mm nominal size and 7.5 cm cement concrete 1:2:4 (1cement :2sand:3 graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of materials in all leads and lifts.

Extra for ornamental decorative work on elevation exposed columns with cement mortar 1;3 (1 Cement : 3 Sand) with chemical adhesive of approved make as per the design and as per the directions of Architect / Engineer in Charge including carriage of materials in all leads and lifts.

Providing & fixing to wall ceiling and floor galvanized mild steel tube (Heavy grade) tube fittings and clamps including making good the wall ceiling and floor and carriage of material in all lead & lift including carriage as per approved brand of Architect/ Site Engineer.

15mm dia

20mm dia

25mm dia

32mm dia

Providing & fixing in trenches, galvanised mild steel tubes (heavy grade) tube fittings earth work in trenches to be measured & paid for separately including carriage as per approved brand of Architect/ Site Engineer.

15mm dia

20mm dia

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete. including carriage as per approved brand of Architect/ Site Engineer.

75mm nominal size ISI

110mm nominal size ISI

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage as per approved brand of Architect/ Site Engineer.:

75mm nominal size

110mm nominal size

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete complete including carriage as per approved brand of Architect/ Site Engineer.:

75mm nominal size

110mm nominal size

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete complete including carriage as per approved brand of Architect/ Site Engineer.:

75mm nominal size

110mm nominal size

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete including carriage as per approved brand of Architect/ Site Engineer.:

75mm nominal size

110mm nominal size

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage as per approved brand of Architect/ Site Engineer.:

75mm nominal size

110mm nominal size

Providing and fixing to wall ceiling and floor marked including fixing with approved adhesive etc. complete including carriage as per approved brand of Architect/ Site Engineer.:

75mm nominal size

110mm nominal size

Providing and fixing PVC double equal branch with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage as per approved brand of Architect/ Site Engineer.:

75mm nominal size

110mm nominal size

Providing and fixing PVC plain double equal branch ISI marked including fixing with approved adhesive etc. complete including carriage as per approved brand of Architect/ Site Engineer.:

75mm nominal size

110mm nominal size

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage as per approved brand of Architect/ Site Engineer.:

75mm nominal size

110mm nominal size

Providing and fixing PVC “Y" junction with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage as per approved brand of Architect/ Site Engineer.:

75mm nominal size

110mm nominal size

Providing and fixing PVC plain “Y" junction ISI marked including fixing with approved adhesive etc. complete including carriage as per approved brand of Architect/ Site Engineer.:

75mm nominal size

110mm nominal size

Providing and fixing PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete including carriage as per approved brand of Architect/ Site Engineer.

110mm nominal size

Providing and fixing PVC reducer ISI marked including jointing with approved adhesive etc. complete.

150 mm X 110 mm dia.

ii) 110 mm X 90 mm dia. Each

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitttings including carriage as per approved brand of Architect/ Site Engineer.

610 x 510 mm with bowl depth 200 mm.

Providing and fixing vitreous China wash down, water closet squatting pan (Indian type W.C pan) size 580mm (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) including carriage as per approved brand of Architect/ Site Engineer. Orissa Pattern

Providing and fixing vitreous China wash down, water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately) including carriage as per approved brand of Architect/ Site Engineer.

Anglo Indian Universal Closet

Providing and fixing to wall ceiling and floor vitreous China low level flushing cistern with a pair of C.I. or mild steel brackets, complete with fitting such as lead valve less syphon, 15mm nominal size brass ball valve with polythene float, C.P. Brass handle, unions and couplings for connections with inlet, outlet and overflow pipes, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately). including carriage as per approved brand of Architect/ Site Engineer.

Providing and fixing G.I. Inlet connection for flush pipe with W.C. Pan. including carriage as per approved brand of Architect/ Site Engineer.

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers including carriage as per approved brand of Architect/ Site Engineer.

Colour type plastic seat & seat cover

Providing and fixing vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately including carriage as per approved brand of Architect/ Site Engineer.

Flat back type of size 430mm x 260mm x 350mm.

Providing and fixing vitreous China squatting plate pattern urinal of size 450mmx350mm with integral longitudinal flush pipe including carriage as per approved brand of Architect/ Site Engineer.

Providing and fixing to wall ceiling and floor with a pair of C.I. Or M.S. brackets complete with fittings including C.I. Syphonic apparatus, mosquito proof lid, C.P. Brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) including carriage as per approved brand of Architect/ Site Engineer.

5 Litres Capacity

Providing and fixing C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clamps etc. (all in C.P. Brass) including cutting holes and making good the same including carriage as per approved brand of Architect/ Site Engineer.

15mm nominal Size

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings including carriage as per approved brand of Architect/ Site Engineer.

630x450mm Flat back

Providing and fixing laboratory sink with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same but excluding fittings including carriage as per approved brand of Architect/ Site Engineer.

Viterous China 600mm x 450mm x 150mm

Providing and fixing C.P. Brass waste for wash basin or sink including carriage as per approved brand of Architect/ Site Engineer. 32mm Dia

Providing and fixing M.I. Union for wash basin or sink including carriage as per approved brand of Architect/ Site Engineer. 32mm Dia

Providing and fixing C.P. Bottle Trap for wash basin and sink including carriage as per approved brand of Architect/ Site Engineer. 32mm Dia

Providing and fixing 600mm x 450 mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers including carriage as per approved brand of Architect/ Site Engineer

Providing and fixing C.P. Brass Towel rail 750mm x 20mmm complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws including carriage as per approved brand of Architect/ Site Engineer

Providing and fixing 600mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws including carriage as per approved brand of Architect/ Site Engineer

Providing and fixing Toilet paper holder CP Brass including carriage as per approved brand of Architect/ Site Engineer

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws as per approved brand of Architect/ Site Engineer

Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous China including carriage as per approved brand of Architect/ Site Engineer

Providing and fixing brass bib tap (Superior or heavy type) with Aerator including carriage as per approved brand of Architect/ Site Engineer 15 mm dia

Providing and fixing Brass stop cocks

Providing and fixing C.P. brass angle valve 15mm without Nuts and pipe.

Providing and fixing 15mm mixer for kitchen sink with top / bottom swinging spout

Providing and fixing one hole basin mixing Faucet

Providing and fixing P.V.C connection with brass unions

15mm nominal bore

20mm nominal bore

Providing and fixing brass full way valve with wheel:-

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

Providing and fixing G.I./M.I Union of following sizes (where not included in the items .

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level :-

2000 Ltrs net Capacity

Providing and fixing to wall ceiling and floor of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete.

Providing and laying (to level or slopes) and jointing with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 sand) salt glazed stoneware pipes grade 'A' of the following internal diameters including testing of pipes and joints complete:

Providing and laying cement concrete 1:5:10 (1 Cement: 5 Sand :10 graded stone aggregate 40mm nominal size ) bedding for stoneware pipes of the following internal diameters, necessary form work and curing complete :

Providing and laying cement concrete 1:4:8 (1 Cement : 4 Sand : 8 graded stone aggregate 40mm nominal size ) bedding for stoneware pipes of the following internal diameters, necessary form work and curing complete

Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 and water tight C. I. cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53kg and frame to be not less than 2.72kg.

Square Mouth Traps : 180mmx100mm size

Providing and laying (to level or slopes) and 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing:

Inside size 800mm x 800mm and 500mm deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm internal dimensions total weight of cover and frame to be not less than 38kg. (Weight of cover 23 kg and weight of frame 15 kg.)

With 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3

manhole 1400mm x 900mm inside size at bottom up to crown of the arch and 600mm x 900mm inside size above crown of the arch Providing and laying (to level or slopes) and with common burnt clay building bricks laid in cement mortar 1:3 (1 cement : 3 sand ) arch work with common burnt clay building bricks in cement mortar 1:4 (1 cement : 4 sand) inside cement plaster 15mm thick with cement mortar 1:3 (1 cement : 3 sand ) with a floating coat of neat cement upto the height of the crown level of arch above the benching level and pointing with cement mortar 1:3 (1 cement: 3 sand) for the remaining portion R.C.C. top slab 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:4:8 (1 cement : 4 sand : 8 graded stone aggregate 40mm nominal size), and making channels in cement concrete 1:2:4 mix (1 cement : 2 sand : graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing.

With C.I. cover and frame (medium duty) 500mm internal diameter total weight of cover and frame to be not less than 116kg (weight of cover 58kg. and, weight

Providing and laying (to level or slopes) and existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3 (1cement : 3 sand) finished with a floating coat of neat cement and making necessary channels with cement concrete 1:2;4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size ) for the drain complete

For pipe 100mm to 150mm internal diameter / nominal size.

Smoke testing of soil or ventilating pipes (new or old) any height or diameter together with the length of drain connecting the soil pipe with the nearest manhole (including use of ladders)

Cutting holes upto 15 cm x 15 cm in R.C.C floors and roofs for passing drain pipe etc. and prepairing the holes after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) including finishing complete so as to make it leak proof.

Cutting holes upto 15 cm x 15 cm in R.C.C floors and roofs for passing drain pipe etc. and repairing the holes after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) including finishing complete so as to make it leak proof.

Davinder Sharma

RAJESH SHARMA