Replacement of Old Dilapidated Type I & II quarters with Type-II for railway Engg, S&T and Operating staff in the jurisdiction of ADEN Hanumangarh-II. (Type-II-14 unit)

B-CPWD DSR Horticulture & Landscaping items 665546.00 Below/P

Preparing / Supply of drawing in Auto CAD (Original + 2 copies) Jet Mat paper of 85/90 GSM showing proper wiring diagram of all electrical installations inside a quarter and power supply arrangement for the above quarters in colony as per site requirement

Item Breakup - A-CPWD DSR 2023 items

slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 11.28S SAND STONE FLOORING 11.31 Extra for pre finished nosing in treads of steps Metre 280 191.4 53592 6 of Kota stone/ sand stone slab. 11.37S CERAMIC GLAZED TILES 11.37 Providing and laying Ceramic glazed floor tiles Sqm 140 1096.55 153517 of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 7 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 11.41S VITRIFIED FLOOR TILES Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with 11.41A grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 11.41A.2 Glazed vitrified floor tiles polished finish of size 8 11.41A.2.1 Size of Tile 600 x 600 mm Sqm 798 1502.75 1199194.5 Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours 11.47 and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). 9 11.47.2 Size of Tile 600x600 mm Sqm 84 1893.9 159087.6 Total 3049825.10 Item- 5 All items of "Finishing" appearing in Chapter No. 13 of CPWD DSR (Amended up to date). S No. Item No Description of Item Unit Qty Rate Amount 13.0 FINISHING 13.4S CEMENT PLASTER (IN COARSE SAND) 13.4 12 mm cement plaster of mix : 1 13.4.2 1:6 (1 cement: 6 coarse sand) Sqm 4200 343.65 1443330 BIKANER DIVISION-ENGINEERING/NORTH WESTERN RLY 15 mm cement plaster on rough side of single 13.5 or half brick wall of mix: 2 13.5.2 1:6 (1 cement: 6 coarse sand) Sqm 4200 395.35 1660470 13.44S EXTERIOR FINISHING Finishing walls with 100% Premium acrylic emulsion paint (Company Depot Tinted) having VOC less than 50 gm/litre and UV resistance as 13.48A per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives. 13.48A.1 New work (Two or more coats applied @ 1.43 Sqm 8400 181.25 1522500 3 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. 13.50 Applying priming coat: 13.50.2 With ready mixed aluminium primer of Sqm 630 74.65 47029.5 4 approved brand and manufacture on resinous wood and plywood Painting with synthetic enamel paint of 13.61 approved brand and manufacture to give an even shade : 5 13.61.1 Two or more coats on new work Sqm 630 155.9 98217 13.80 Providing and applying white cement based Sqm 9100 156.05 1420055 putty of average thickness 1 mm, of approved 6 brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Total 6191601.50 All items of "New Technologies and Materials" appearing in Chapter No. 26 of CPWD DSR (Amended Item- 6 up to date). S No. Item No Description of Item Unit Qty Rate Amount 26.0 NEW TECHNOLOGIES AND MATERIALS 26.73S PREFAB/PRECAST TECHNOLOGY Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws 26.86 having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). 1 26.86.1 Frame size 45 x 70 mm Metre 658 705.85 464449.3 BIKANER DIVISION-ENGINEERING/NORTH WESTERN RLY Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate a n d natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 26.88 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. 2 26.88.1 30 mm thick Sqm 238 4764.2 1133879.6 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) 26.89 having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. 3 26.89.1 18 mm thick Sqm 224 2992.9 670409.6 Total 2268738.50 Item- 7 All items of "All other chapters" of CPWD DSR (Amended up to date) except mentioned above. S No. Item No Description of Item Unit Qty Rate Amount 8.0 CLADDING WORK 8.1S General Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base 8.2 cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite stone slab colour black, Cherry/Ruby 8.2.2 red 1 8.2.2.1 Area of slab upto 0.50 sqm Sqm 49 5413.5 265261.5 BIKANER DIVISION-ENGINEERING/NORTH WESTERN RLY 2 8.2.2.2 Area of slab over 0.50 sqm Sqm 42 5136.3 215724.6 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including 8.3 machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 3 8.3.2 Granite work Metre 210 510.95 107299.5 8.4 Extra for fixing marble /granite stone, over and Metre 42 568.55 23879.1 above corresponding basic item, in facia and 4 drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. 8.5 Extra for providing opening of required size & Each 14 978.7 13701.8 shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in 5 marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 8.20S STONE WORK DRY CLADDING 8.31 Providing and fixing Ist quality ceramic glazed Sqm 532 1267.95 674549.4 wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by 6 Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 9.0 WOOD AND P.V.C. WORK 9.40S MISCELLANEOUS-WOOD WORK Providing and fixing nickel plated M.S. pipe 9.47 curtain rods with nickel plated brackets : 7 9.47.2 25 mm dia (heavy type) Metre 210 186.4 39144 9.70S STAINLESS STEEL FITTINGS Providing and fixing IS : 12817 marked 9.70 stainless steel butt hinges with stainless steel screws etc. complete : 8 9.70.2 100X58X1.90 mm Each 28 107.1 2998.8 9 9.70.3 75x47x1.80 mm Each 28 80.05 2241.4 9.72S BRASS FITTINGS 9.84 Providing and fixing aluminium extruded Each 42 983.15 41292.3 section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 10 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 9.88S CHROMIUM PLATED BRASS FITTINGS Providing and fixing special quality chromium plated brass cupboard locks with six levers of 9.90 approved quality including necessary screws etc. complete. 11 9.90.1 Size 40 mm Each 28 319.75 8953 ANODISED ALUMINIUM FITTINGS (ALL FITTINGS 9.95S SHALL BE ISI MARKED) Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not 9.96 less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 12 9.96.2 250x16 mm Each 224 260.6 58374.4 BIKANER DIVISION-ENGINEERING/NORTH WESTERN RLY Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than 9.97 grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 13 9.97.3 200x10 mm Each 196 99.7 19541.2 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 9.101 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 14 9.101.2 Twin rubber stopper Each 112 72.35 8103.2 9.105S GYPSUM BOARD PARTITIONS Providing and fixing magnetic catcher of approved quality in cupboard / ward robe 9.114 shutters, including fixing with necessary screws etc. complete. 15 9.114.2 Double strip (horizontal type) Each 112 39.7 4446.4 9.115 Providing and fixing powder coated telescopic ONE 28 414.2 11597.6 drawer channels 300 mm long with necessary SET 16 screws etc. complete as per directions of Engineer- in-charge. Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 9.134 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 35 mm thick shutters With ISI marked stainless 9.134.1.2 steel butt hinges of required size 9.134.1.2.3 Kiln seasoned selected class of sheesham Sqm 98 4740.3 464549.4 17 wood Providing and fixing bright /matt finished 9.165 Stainless Steel handles of approved quality & make with necessary screws etc all complete. 18 9.165.1 125 mm Each 224 119.2 26700.8 19 9.165.2 100mm Each 112 90.45 10130.4 9.171 Providing and fixing stainless steel soft closing Each 224 272 60928 spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard 20 shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge. 10.0 STEEL WORK 10.1S General Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash 10.11 bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment). 10.11.1 Fixing with 15x3 mm lugs 10 cm long Kg 4900 131.05 642145 embedded in cement concrete block 15x10x10 21 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) BIKANER DIVISION-ENGINEERING/NORTH WESTERN RLY Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position 10.16 and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 22 10.16.1 Hot finished welded type tubes Kg 2800 194.4 544320 10.18 Providing and fixing circular/ Hexagonal cast Each 56 220.65 12356.4 iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be 23 screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. Providing & fixing fly proof wire gauze to 10.29 windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. 10.29.2 Stainless steel (grade 304) wire gauze of 0.5 Sqm 168 1133.55 190436.4 24 mm dia wire and 1.4 mm aperture on both sides Providing and fixing glass panes with putty and 10.30 glazing clips in steel doors, windows, clerestory windows, all complete with : 25 10.30.2 5.5 mm thick glass panes Sqm 168 1390.15 233545.2 12.0 ROOFING 12.1S SHEET ROOFING Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone 12.21 aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 26 12.21.1 In 75x75 mm deep chase Metre 560 305.15 170884 12.22 Making khurras 45x45 cm with average Each 14 298.25 4175.5 minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over 27 P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 12.24S CEILING Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 12.31 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately): 28 12.31.1 Flat surfaces Sqm 140 1718.95 240653 12.32 Extra for sunk or raised mouldings in the Sqm 54 607.45 32802.3 29 plaster of Paris (Gypsum anhydrous) ceiling. 12.37S RAIN WATER SPOUT AND PIPE Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 12.41 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 30 12.41.2 110 mm diameter Metre 700 377.4 264180 BIKANER DIVISION-ENGINEERING/NORTH WESTERN RLY Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes 12.42 conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 12.42.4 Single tee without door 31 12.42.4.2 110x110x110 mm Each 70 221.35 15494.5 12.42.5 Bend 87.5 degree 32 12.42.5.2 110 mm bend Each 70 150.35 10524.5 12.42.6 Shoe (Plain) 33 12.42.6.2 110 mm Shoe Each 70 131.85 9229.5 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of 12.43 required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 34 12.43.2 110 mm Each 140 371.3 51982 12.44 Providing and fixing to the inlet mouth of rain Each 112 54.7 6126.4 35 water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 15.0 DISMANTLING AND DEMOLISHING 15.1S General Demolishing cement concrete manually/ by mechanical means including disposal of 15.2 material within 50 metres lead as per direction of Engineer - in - charge. 15.2.1 Nominal concrete 1:3:6 or richer mix (including cum 28 2434.25 68159 36 equivalent design mix) Demolishing brick work manually/ by mechanical means including stacking of 15.7 serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 37 15.7.4 In cement mortar cum 70 2060.2 144214 15.60 Disposal of building rubbish / malba / similar cum 168 263.95 44343.6 unserviceable, dismantled or waste materials by mechanical means, including loading, 38 transporting, unloading to approved municipal dumping ground or as approved by Engineer- in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 16.0 ROAD WORK 16.42S CONCRETE PAVEMENTS 16.44 Extra for providing and mixing hardening Litre 2800 55.5 155400 compound of approved quality as per 39 manufacturer's specification in cement concrete. 16.49S MISCELLANEOUS BIKANER DIVISION-ENGINEERING/NORTH WESTERN RLY 16.69 Providing and laying at or near ground level cum 14 10117.6 141646.4 factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more 40 than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in- charge). 16.75 Providing and laying C.C. pavement of mix M- cum 70 9823.8 687666 25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , 41 vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick 16.91 compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 16.91.2 80 mm thick C.C. paver block of M-30 grade Sqm 700 1091.5 764050 42 with approved color design and pattern. 17.0 SANITARY INSTALLATIONS 17.1S General Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with 17.1 manually controlled device (handle lever) conforming to IS : 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. pan Each 14 6767.4 94743.6 43 of size 580x440 mm with integral type foot rests Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush 17.2 pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1 W.C. pan with ISI marked white solid plastic Each 14 6515.55 91217.7 44 seat and lid BIKANER DIVISION-ENGINEERING/NORTH WESTERN RLY 17.7A Providing and fixing wash basin with C.I. Each 42 3960.55 166343.1 brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and 45 making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer 17.8 Providing and fixing white vitreous china Each 42 1683.35 70700.7 pedestal for wash basin completely recessed 46 at the back for the reception of pipes and fittings. Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, 17.10 including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.2 Kitchen sink without drain board 47 17.10.2.2 610x460 mm bowl depth 200 mm Each 14 3873.8 54233.2 Providing and fixing P.V.C. waste pipe for sink 17.28 or wash basin including P.V.C. waste fittings complete. 17.28.1 Semi rigid pipe 48 17.28.1.1 32 mm dia Each 56 103.9 5818.4 17.31 Providing and fixing 600x450 mm bevelled Each 28 1607.95 45022.6 edge mirror of superior glass (of approved 49 quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP 17.73 brass screws with concealed fittings arrangement of approved quality and colour. 17.73.2 600 mm long towel rail with total length of 645 Each 28 708.95 19850.6 50 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 18.0 WATER SUPPLY 18.7S C.P.V.C. PIPES Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, and all CPVC plain & brass threaded fittings, including fixing the 18.7 pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. ( Internal work - Exposed on wall ) 51 18.7.2 20 mm nominal dia Pipes Metre 45 335 15075 52 18.7.3 25 mm nominal dia Pipes Metre 840 401.55 337302 53 18.7.6 50 mm nominal dia Pipes Metre 420 934.15 392343 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one 18.8 step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 54 18.8.2 20 mm nominal dia Pipes Metre 700 537.6 376320 18.15S BRASS FITTINGS BIKANER DIVISION-ENGINEERING/NORTH WESTERN RLY Providing and fixing gun metal gate valve with 18.17 C.I. wheel of approved quality (screwed end) : 55 18.17.1 25 mm nominal bore Each 14 622.4 8713.6 56 18.17.1A 20 mm nominal bore Each 14 539.95 7559.3 Providing and fixing ball valve (brass) of 18.18 approved quality, High or low pressure, with plastic floats complete : 57 18.18.2 20 mm nominal bore Each 14 462.5 6475 Providing and fixing uplasticised PVC 18.21 connection pipe with brass unions : 18.21.1 30 cm length 58 18.21.1.1 15 mm nominal bore Each 14 85 1190 C.I. SLUICE VALVES/ FIRE HYDRANTS & 18.31S FIXTURES 18.48 Providing and placing on terrace (at all floor Per 14000 11 154000 levels) polyethylene water storage tank, IS : Litre 12701 marked, with cover and suitable locking 59 arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 18.49S C.P. BRASS FITTINGS Providing and fixing C.P. brass bib cock of 18.49 approved quality conforming to IS:8931 : 60 18.49.1 15 mm nominal bore Each 28 506.8 14190.4 Providing and fixing C.P. brass long nose bib 18.50 cock of approved quality conforming to IS standards and weighing not less than 810 gms. 61 18.50.1 15 mm nominal bore Each 28 820.7 22979.6 Providing and fixing C.P. brass long body bib 18.51 cock of approved quality conforming to IS standards and weighing not less than 690 gms. 62 18.51.1 15 mm nominal bore Each 28 798.95 22370.6 Providing and fixing C.P. brass stop cock 18.52 (concealed) of standard design and of approved make conforming to IS:8931. 63 18.52.1 15 mm nominal bore Each 28 670.45 18772.6 Providing and fixing C.P. brass angle valve for 18.53 basin mixer and geyser points of approved quality conforming to IS:8931 64 18.53.1 15mm nominal bore Each 112 574.3 64321.6 18.54S PTMT FITTINGS Providing and fixing PTMT grating of approved 18.58 quality and colour. 18.58.1 Circular type 65 18.58.1.1 100 mm nominal dia Each 84 37.6 3158.4 22.0 WATER PROOFING 22.1S General 22.14 Grading roof for water proofing treatment with 22.14.1 Cement concrete 1:2:4 (1 cement : 2 coarse cum 56 8042.3 450368.8 66 sand : 4 graded stone aggregate 20 mm nominal size) Total 8936820.30

Item Breakup - B-CPWD DSR Horticulture & Landscaping items