Work

Amount

Dismantling of following equipments and structure including shifting to other place in switchyard and other associated works-

Opening of 33kV Capacitor bank bay control cable wiring and shifitng/ termination to new place including provision of additional Junction box for cable looping in switchyard including both side gland, ferrule, dressing etc.

Opening of all connected jumpers from 33 KV main bus, single span.

Dismantling and lowering down of each phase of 33 KV main bus, single span with the help of suitable hardware fittings and T & P and cutting of one side Panther conductor in existing bus complete in all respect.

Dismantling of structure (ALP-9, ABL-3)

Dismantling of 36KV CT/PT/NCT

Dismantling of 36KV LI

Dismantling of 36KV BI

Dismantling of 36KV VCB

Dismantling of 36KV CT/PT JB

Dismantling of 3 ph Reactor oil cooled

Dismantling Capacitor Bank Units (5MVAR each set) incl support frame.

Carriage of structure/materials from Electy. Fabrication unit Naini Prayagraj/other Substation To 132KV S/S Jagdishpur - Amethi.

Sorting, counting, stacking mark wise and head loading of structure on Truck/Trailer (6.85 MT)

Safe carriage loaded structure from Electy. Fabrication unit Naini Prayagraj to 132KV S/S Jagdishpur- Amethi. Distance approx. 180km (6.85 MTX180km=1233MT-KM)

Unloading of carriage structure from Truck/Trailer its sorting, Counting and proper Stacking at the S/S premises as per directing of supervisioning engineer (6.85 MT)

Erection of following equipments and structure as per drawing instruction manual of various equipments including shifting from store to erection site and other associated work.

Erection of main and auxiliary structure, mast etc. The job consist of shifting of all materials i.e. structure parts, nut bolt, washers etc. from store to site of erection. Erection of structure as per relevant drawing and practices using flat/spring washer with each bolt matching holes. Cutting, notching of members if required shall also be done by contractor without any extra cost to complete the work satisfactorily.

Erection of following 33KV 1x10MVAr (Dismantled) & 1x10MVAr(new) Capacitor Bank equipments and 33KV Main Bus (extension) equipments including shifting of materials from store to work site:

PT junction box

33KV LA/ PI

33 KV Line Isolator

33 KV Bus Isolator

33 KV VCB

CT junction box

Capacitor cells 24 microfarad

Series Reactor

Fabrication & connection of Moose/Panther & Panther/Panther jumpers complete in all respect.

Laying of 1.1 KV Unarmored copper control cable from various 33KV Capacitor Bank equipments (new & old unit) and new 33KV Main Bus(extension) equipments to C&R Panels.

2xCx2.5 sqmm.

4xCx2.5 sqmm.

6C x 2.5 sqmm.

Erection of Control & Relay panel of New Capacitor Bank.

33KV Capacitor bank bay both sides control cable terminations on CT, CB, PT and control & Relay panel etc. as per drawing including cost of cable glands, lugs and ferrules except control cable complete as per drawing & site requirement.

Stringing of each phase of 33 KV Bus bar (1 x Panther Conductor) for 12mtr span (for capacitor Bank Bus of new 1x10MVAr unit and old 1x10MVAr unit) total 2span, including fitting of tension & suspension clamps, hoisting of insulators, cutting of conductor etc. performing all other associated work to complete the job satisfactorily.

Stringing of each phase of 33 KV Bus bar (1 x Moose Conductor) for 33KV Main Bus(extension) in two span each span 12mtr, including fitting of tension & suspension clamps, hoisting of insulators, cutting of conductor etc. performing all other associated work to complete the job satisfactorily.

Providing & Fixing of 3 Phase L.T. A.C. Supply Cubicals of size 1200×600×500 mm with Hinged Door and Proper Locking Arrangement duly made of 16 SWG M.S. Sheet and Painted with Grey Colour Synthetic Enamel Paint. The L.T. A.C. Supply Cubical should be Fitted with 3 Nos. 100 Amp. Copper Bus Bar (3 Phase + Neutral), 5 No. 32 Amp. TPN MCB, 12 No. 40 Amp. DP MCB, 40 No. Link type Terminal Bock, Cable Glands etc. with Internal Wiring and then Installation of each L.T. A.C. Cubical on 1 meter long M.S. Angle Frame Structure after due Fabrication with the help of Scrap M.S. Angles to be Provided by the Department Free of Cost and Grouting of Legs of the M.S. Angle Frame Structure in the Ground with C.C. Mixture and Painting of the M.S. Angle Frame Structure with Synthetic Enamel Paint. (1 Job per L.T. A.C. Cubical)

Earthing of L.T. A.C. Supply Cubical with Providing & Fixing of 600 × 800 × 8 mm size G.I. Plate with its Top At Least 3 Meter below the Ground Level with 20 mm dia. G.I. Pipe & Funnel for Watering, 1 No. 8 SWG G.I. Wire Earthing Lead etc. with Alternate Layer of Charcoal / Coke and Salt at Least 150 mm Thick Around it.

Providing & Fixing of 150 Watt L.E.D. Street Light Luminaries Fittings of Philips / Compton Greaves / Havells make with IP 65 rating in Single Piece Die Cast Aluminium Alloy Housing with Pot Optics Reflector & Toughened Clear Glass Cover with Frame for Lamp Compartment inlcuding Cable Terminations.

Providing & Fixing of Junction Box of size 280 × 225 × 150 mm duly made of 16 SWG Sheet and Painted with Smoke Grey Colour Synthetic Enamel Paint and Fitted with 1 No. 6 Amp. SP MCB on Anodized M.S. Channel, 1 No. Bakelite Fuse Fitting with 6 Amp. NS 6 type HRC Fuse, 1 No. Copper Neutral Link, Bakelite Terminal Block of 4 Terminals, Cable Glands suitable for 2C × 2.5 mm2 / 4C × 2.5 mm2 size Incoming / Outgoing Control Cables etc., then Installation of Junction Box on M.S. Round Pole at designated Height with the help of suitable M.S. Clamps alongwith Earthing of the Junction Box with 12 SWG G.I. Wire including Cable Terminations with Satisfactory Testing & Commissioning

Providing & Fixing of G.I. S.L. Pole Bracket duly made of 40 mm dia. 1.2 Meter Long ‘B’ Class Pipe and Bent at One End by Quarter Circle in 1.0 Meter at an Angle of 300 for Fixing of 150 Watt LED Street Light Luminaries Fittings on M.S. Round Pole with help of M.S. Clamps

Laying of 3.5x70/50 sq.mm LT Power Cable, 50cm below the ground level after Excavation of trench, Laying the 1st class brick lining, filling of river sand along & over the cable, then back filling & levelling the trench after Laying of Cable. The work also includes Termination of cable on both sides with Crimping of Lugs.

Laying of 2C x 2.5sq.mm size Control cables from LT A.C.D.B. Cubical to various junction Boxes for Switchyard Lighting through through Excavated Trench of size 300x600 mm, Covering the cables with River Sand & Brick Lining along & Over the Cable, then Back filling & levelling of the trench after Laying of Cables.

Laying of above Control Cables from L.T. Lighting Junction Box to LED Street Light Fittings by clamping with suitable M.S. Strip Clamp with proper Dressing etc.

Providing & Fixing of Cable Marker duly made of Cast Iron.

Earthing by Cutting, Straightening & Laying 500 mm below Inside Ground & above Ground of Following sizes M.S. Round Bar, Provided by the Department for Diagonal / Double Earthing of the Main & Aux. Structures, Equipments and Cable Trenches including Welding with Main Earth Mat and with the Object to be Earthed including Excavation of Trenches & its Back Filling etc. as per Details below :

40mm dia MS Round Bar for Earth-Mat

Earthing Electrode of 40mm Dia of 03 meter length

Earthing by Cutting, Straightening & Laying 500 mm below Inside Ground & above Ground of Following sizes for Diagonal / Double Earthing of the Main & Aux. Structures, Equipments and Cable Trenches including Welding with Main Earth Mat and with the Object to be Earthed including Excavation of Trenches & its Back Filling etc. as per Details below :

Earthing of Main Structure with 50 × 6 mm size M.S. Flat

Aux. Structures and Equipments (CBs, Isolators, CTs, PTs, C&R Panel, DPP, Junction Boxes etc. with 50 × 6 mm size M.S. Flat

Painting of M.S flat size 50x6 sq. Mm. After using red oxide primer and painting with green color ISI marked paint two coats on both sides.

Supply of various Items required for erection of structures and equipments and stringing work along with earthing of the equipment and structures for extension of 33KV Main Bus and Capacitor Bank Bus along for Shifting of existing and New Capacitor Bank

Single Tension Fittings Suitable for ACSR Moose

Single Tension Fittings Suitable for ACSR Panther

PG Clamps suitable for Moose / Moose

PG Clamps suitable for Moose / Panther

PG Clamps suitable for Panther / Panther

Bus Post Clamp suitable for Moose

M/S SHRI RAMRAJ TRADERS

M/s Janta Charan

ASIA ENTERPRISES

M/S SATTYAM CONTRACTORS