PROVN OF CERTAIN LBW AND SPECIAL REPAIR AT LGJ MIL STN

Amount

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, complete all as directed by Engineer-in-Charge.

Material and labour for reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed by Engineer-in-Charge.

M & L for cement concrete 1:1.5:3, type A-1 (using 20mm graded stone aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings bed block, roof kerbs or mud stops, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

M & L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required including bending, cranking etc and binding with and including MS wire (annealed) not less than 0.9 mm dia, complete all as specified & directed by Engineer-in- charge.

M & L for mild steel TMT bars 6 mm to 8mm dia cut to length, bent to shape required including bending, cranking etc and binding with and including MS wire (annealed) not less than 0.9mm dia, complete all as specified & directed by Engineer-in- charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Surface excavation N.exc. (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as specified and directed by Engineer-in-Charge.

Removing excavated materials n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

M&L for precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in kerb stones size 300mm x 300mm x 100mm with plain fair faces, including chamfers, weathering, throating etc setting in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base below floors complete all as specified and directed by Engineer-in-Charge.

M&L Machined pressed precast concrete interlocking paver block glossy with grey cement and pigment, any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with over 50mm thick Fazilka sand cushion complete all as specified and directed by Engineer-in-Charge.

M&L for filleting in any position and to any shape in cement mortar 1:4 including all mitres, stops, etc section of fillet n.exc. 25 sq. cm complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

Removing mortar from and cleaning bricks, stacking for measurements inclusing all extra handling and removal of disposing off rubbish complete all as specified and directed by Engineer-in-Charge.

M&L brick work with subclass 'B' bricks,old size bricks straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

,----Ditto-- All as per Serial item No 15 above but except bricks complete all as specified and directed by Engineer-in-Charge. Note : The old serviceable brick shall be used.

M&L Key Pointing to brick walls in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of new plastered or pointed surface of walls/pillars/cornices by sand papering or by any other mean and after preparing the surfaces applying two coats of cement base paint as approved tint/colour over a one coat of priming paint complete all as specified and as directed by Engineer-in-Charge.

Rough excavation not exceeding 1.5 m deep and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Forming embankments including raising (or loweing) earth, spreading in layers n.exc 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc. n.exc 1.5 m high from base complete all as specified and directed by Engineer-in-Charge.

Forming embankments including raising (or lowering) earth, spreading in layers n.exc 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc. exc 1.5 m and n.exc 3.0 m high from base all as specified and directed by Engineer-in-Charge.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, shelf slab, landings and similar work not exceeding 200mm thick including edges rough finished complete all as specified and as directed by Engineer-in- charge.

Material and labour for granite slab 20mm thick machine cut,over 15mm screed bed cm (1:4) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and and directed by Engineer-in-Charge.

Material and labour for rounding to edge of granite slab in cooking platform and other similar situation including grinding and polishing complete all as specified and and directed by Engineer-in-Charge.

Dismantling of brickwork or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge.

Material and labour for brick work in half brick thick wall using fly ash bricks (old size bricks) straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified & directed by Engineer-in- charge.

Supply and fixing in repair stainless steel kitchen sink with drain board, made out of 1.00mm thick sheet for kitchen with washers, waste coupling and waste pipe.overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed by the Engineer-in-Charge.

Supply & fixing stainless steel plate rack made out of 1mm thick stainless steel sheet of size 24" x 24" x 10" including taking down existing wooden plate rack complete all as specified and directed by Engineer-in-Charge. Make : Prayag, Cat part No- 310.

Taking down cement plaster of any description from brick walls or concrete surfaces of walls and ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles 300mm x 450mm x 7mm thick as in vertical surface such as skirting, dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed by Engineer-in-Charge.

M&L for Non skid ceramic coloured tiles (Jointless) 7 to 8mm thick (square/rectangular) area of each tile (300 x 300mm) exceeding 0.06 sqm but n exc 0.11 as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured highliter tiles or border tiles minimum width of times 80mm to 100mm as in vertical surface such as skirting, dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of wall surfaces/putty surfaces by sand paper with mechinical method i.e. Hand electric grinder and applying two coats of oil bound distemper over one coat of chalk whiting primer inclusive all as specified with mechinical method i.e. spray gun etc, complete all as specified & directed by Engineer-in-charge.

Material and labour for rendering/plastering 10mm thick in cement mortar (1:4) on concrete surfaces of ceiling, finished fair and even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparing newly plastered undecorated surface of ceiling by sand papering or by any other mean and after preparing the surfaces applying three coats of white wash complete all as specified & directed by Engineer-in- charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each and removing from site complete all as specified and as directed by Engineer-in- charge.

S&F factory made steel ventilator with half portion fixed type and half top portion top hung shutter including box type hinges, steel peg stay with glazing bar, fixing lugs in PCC ( 1 : 2 :4) type B-1 complete all as specified and directed by Engineer-in- charge.

Supply & fixing 4mm thick figured glass ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in- charge.

Supply & fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tack or stainless steel wire staples complete all as specified & directed by Engineer-in- charge

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed by Engineer-in- charge.

Supply and fixing in repair fancy type chromium plated bib tap, cast copper alloy, with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferrule & fixed suitable for 15mm bore iron pipe complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS

Supply & fixing in repair chromium plated Angle cock, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe suitable for size 15mm bore complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve shall be as given in SSR or in relevant IS.

Supply & fixing in replacement stop valve fancy type, cast copper alloy, chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union, size 15mm bore complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve shall be as given in SSR or in relevant IS. Make : Prayag, Model for concealed stop cock No:TRANQUIL-Code No-7318)

Supply and fixing in repair 10 litres capacity PVC valveless syphonic action type low level flushing cistern white with inlet, ball valve, float, handle including brackets and 32mm dia PVC flush pipe, PVC connection 600 mm long with PTMT nuts suitable for 15mm bore pipe including taking down old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair Indian type water closet Orrisa pattern Size 445 x 585 x 260mm with 'P' trap 220mm complete all as specified and directed by Engineer-in-Charge. Colour shall be decided by Engineer-in-Charge.

Supply and fixing in replacement 450mm long PVC connection 15mm size with PTMT nuts complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair chromium plated fancy type soap dish complete all as specified and directed by Engineer-in-Charge.

Taking up or down existing galvanised steel water tubing (GI pipe) 15mm bore including fitting/connection from wall/ceiling/floor etc. including cleaning for reuse or removing complete all as specified and as directed by Engineer-in-charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 15mm bore with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement stainless steel grating round or square150mm size (minimum weight 100gms) complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

S&F in repair chromium plated tubular towel rail 20mm dia 'D' type, 60cm long complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement pillar tap swan neck fancy type, cast copper alloy with capstan head, chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long screwed shank and fly nuts, screwed for iron pipe 15mm bore complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant

Supply & fixing in replacement brass chromium plated 4" Multi flow overhead shower with 225mm arm & flange including fixing to 15mm bore pipe complete all as specified and as directed by Engineer-in-charge. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

M/s Karan Builders

ram rattan dass aggarwal

PAREEK AND COMPANY

NATIONAL ENTERPRISES

KHANNA CONSTRUCTIONS

Aggarwal brothers and company