SPECIAL REPAIR TO KVS ACCOMODATION AT AF STN JAISALMER.

Amount

Taking down chowkats or frame with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n exc 4 Sqm each complete all as specified and directed.

Taking down chowkats with shutter (without taking off shutter from the frame) n exc 1.5 Sqm each complete all as specified and directed.

Taking down shutter of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed

Taking down cement plaster of any description, on brick or stone walls/ceiling etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar beading (but not backing), removing serviceable tiles from site store and rubbish off the premises complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Demolition of brick/stone work masonry built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar faces and precast concrete articles complete all as specified and directed.

Demolition of existing sunken floor water proofing treatment/cement plaster/cement concrete,any description and removing the debries from site not exc 150 m from site complete all as specified & directed.

Taking up or down 15mm bore steel tubing with connections including cleaing for refixing or removal from site complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections including cleaing for refixing or removal from site complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in Brick /stone wall complete all as specified and directed.

Taking down existing roof treatment ,concrete any description and disposal of debries out of permises and scrubbing down with water etc,preparing the surface to receive plaster by brushing and fanning the surface to all loose dirt etc. complete all as specified and directed.

Cutting out cracks to V-section in existing roofs or terracing ,cleaning out ,wetting,grouting with cement and sand slurry (1:3) complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Demolition and breaking up drain pipes of 150 mm dia (Salt glazed ware ,AC or Reinforced concrete ) set in cement mortar including bedding haunching complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm using excavated soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point for soil complete all as specified and directed.

Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided for and removing the debries to distance not exc 50 m from site complete all as specified and directed.

S&F 35 mm thick 2nd class hard wood plain, framed , paneled shutters (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I) , kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight chowkats and frames wrought, framed rebated on the solid, rounded or chamfered, put togather with glue pinned at joint. complete all as specified and as directed.

S&F 35mm thick 2nd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc of size members of shutters as specified in SSR Part-1, section 8, clause 8.24(a) and as directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, with glazing bars, dovetailed including one shop coat of zinc chromate primer complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, without glazing bars, dovetailed including one shop coat of zinc chromate primer complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, including one shop coat of zinc chromate primer complete all as specified and directed.

S&F solid PVC door frame of size 50 x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube as per specification and drawing.

S&F 30 mm thick (style) factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvant cement, all as per specification and drawing. Note: Contractor shall give 6 years guarantee for PVC shutters.

M&L for plain cement concrete (1:2:4), type B-0 using 12.5mm graded stone aggregate as in bed block for hold fast complete incl necessary formwork etc complete all as specified and directed.

S&F MS hold fasts and similar small articles conforming to Fe 290 Gde-E-165 complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads including punching or drilling out old glazing pins/springs clips also providing and fixing new ones complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 3mm thick figured glass pin headed type and glazing with oil putty in square n exc 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm using stainless steel wire staples complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4mm fixed to steel windows / wooden doors with GI wire staples complete all as specified and directed.

S&F 250 mm long aluminium alloy anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

S&F Mild Steel framed work such as grills, gratings, etc., with end of bars shouldered and/ or riveted forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; framework of water tank and similar work conforming to Fe- 290. Gde - E 165 complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section fixed complete all as specified and directed

S&F 150mm size aluminium door handle cast type anodised complete all as specified and directed

S&F 300 mm long ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and directed

S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin , anodized and fixed , type C-21 complete all as specified and directed

S&F 100mm size butt hinge medium weight cold rolled mild steel complete all as specified and directed.

M&L for 10 mm thick rendering cement plaster in cement mortar (1:6) on surfaces other than of fair faces of brick or concrete wall surfaces, finished even and smooth without using extra cement complete all as specified and directed

M&L for 15mm thick rendering cement plaster in cement mortar (1:4) on surfaces of fair faces of brick or concrete wall surfaces, finished even and smooth without using extra cement mixed with 3% integral water proofing compound by weight of cement complete all as specified and directed

M&L for 5 mm thick rendering cement plaster in cement mortar (1:3) on uneven faces of concrete surfaces in ceilings and finished even and smooth without using extra cement complete all as specified and directed.

M&L for Guniting for shortcrete 1:2(CM) mixed with epoxy resin and hardner (manufactured by FOSROC/MC BAUCHEMIC/CICO/PIDILITE)@2% by weght of cement in equal Proportion using short crete pumps and allied equipment in thickness 30mm all as per manufacturers instruction for chajjahs,roof projections etc,as ordered in any positions and floors complete all as specified and directed.

Preparing new plastered surfaces of walls and applying 1mm thick readymixed wall putty on entire surface of wall etc cutting and finishing with appropriate sand paper and applying two coats of oil bound distemper (White or tinted) over one coat of primer after smoothening of surfaces complete all as specified and directed.

Complete removal of existing treatment on old plastered surfaces of walls, filling up undulation and applying 1 mm thick readymixed wall putty on entire surface of wall etc cutting and finishing with appropriate sand paper and applying two coats of oil bound distemper (White or tinted) over one coat of primer after smoothening of surfaces complete all as specified and directed.

Preparing old decorated or unplastered surfaces of walls by brooming down, scraping down smoke soot, mould, moss and efflorescent salts and greasy spots and applying one coat of exterior emulsion paint (APEX of Asian Paints or equivalent in NEROLAC, JENSON & NICHOLSON, BERGER PAINTS) of any colour as approved by GE complete all as specified and directed. Note: 1. Contractor shall furnish guarantee for period of 05 years on stamp paper worth Rs. 500.00 from the actual date of completion of work for rectification of defects. 2. Contractor shall deposit security amount as per table in clause 24.3 of PS on serial page No. 127.

Preparing new plastered surfaces of walls and applying two coats of exterior emulsion paint (APEX of Asian Paints or equivalent in NEROLAC, JENSON & NICHOLSON, BERGER PAINTS) over a coat of primer of any colour as approved by GE complete all as specified and directed. Note: 1. Contractor shall furnish guarantee for period of 05 years on stamp paper worth Rs. 500.00 from the actual date of completion of work for rectification of defects. 2. Contractor shall deposit security amount as per table in clause 24.3 of PS on serial page No. 127. 3. Primer and exterior emulsion paint shall be of same manufacturer.

Preparing old treated surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

Preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Preparing new wodden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparing old wooden surfaces and applying one coat of synthetic enamel paint including cleaing of spots over wooden surfaces complete all as specified and directed.

Preparing new steel surfaces of any description, over 10cm in width or girth, not other wise described and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed.

Complete removal of existing paint and preparing old steel surfaces and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete to match in floor over and including 15 mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, on verticle surfaces, dados, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete to match in floor over and including 10 mm thick rendering cement plater in cement mortar (1:4) complete all as specified and directed.

M&L non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete to match in floor over and including 15 mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed.

M&L for (300mm x450mm) and 6 to 7 mm thick coloured glazed ceramic tiles on verticle surfaces, dados, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete to match in floor over and including 10 mm thick rendering cement plater in cement mortar (1:4) complete all as specified and directed.

M&L for 20 mm thick Granite cooking platforms and like in 15 mm thick cement morter (1:6) screed bed including pointing in match cement (1:2) using Marble dust with admixture of pigment to match with shade of Granite complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge such as in steps,cooking platform,and other similer situations complete all as specified and directed.

M&L for 20mm thick Machine cut Kota stone slab flooring over and including 15 mm thick screed bed or bedding layer in cement mortar (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc. complete all as specified and directed.

M&L for 20mm thick Machine cut Kota stone slab as in riser of steps, skirting, dados etc over and including 15 mm thick rendering in cement plaster (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed.

M&L for reinforced Cement concrete in (1:2:4) type B1 using 20mm graded aggregate as in slab supported on wall, beams and cloumns in floors, kitchen platform, roof projection, landings, blaconies, canopies, deck slab and in shelves, chajjas etc complete all as specified and directed.

S&F 10mm dia and over mild steel TMT bars cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs,roof projection,chajjas, landings and similar work n. exc 200mm thick for flat rough finished surfaces of concrete complete all as specified and directed.

S&F rolled mild steel joists,channel, angle or tee sections Fe-410 W (Gde-E-250) as in farming for roof projection complete all as specified and directed.

M&L for precast cement concrete solid blocks masonry cement concrete (1:3:6) type C-I using 20mm graded stone aggregate, exc 10cm in width and set in cement mortar (1:6) etc complete all as specified and directed.

M&L for 10 mm thick rendering cement plaster in cement mortar (1:3) floor and wall surfaces in sunken floor mixed with 3% integral water proofing compound by the weight of cement complete all as specified and directed.

M&L for Water proofing treatment to sunken surface complete all as specified & directed with the following: (a) Applying evenly a tack coat of industrial Bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surfaces. (b) Applying APP modified polymeric membrane of weight not less than 3.0 kg/sqm and minimum 3 mm thick reinforced with polyster woven fabric ( weight not less than 150gms/sqm, laid over primed surface bu forced application and bonded to the sub strata by heat process,over laps of 100 mm shall be sealed/fushed by flames torch application as per manufacturer's instructions.

Supply only integral water proofing compound complete all as specified and directed.

S&F in repair vitreous china wash down water closet (Pedestal pattern) including connection to drain (or out going pipe )and to flushing pipe ,anti-sypohonage pipe etc. with plastic water closed seat cover (white)closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device hinge device, complete all specified and directed .

S&F in repair water closet vitreous china squatting pan Orissa pattern of size 580x440mm white with integral foot rest front/back inlet (excluding flushing cistern and flush pipe) including provision of cement concrete bedding in PCC (1:5:10) type E-2 and making good to disturbed surface complete all as specified and directed.

S&F in repairs wash hand basins, vitreous china( flat back) white of size 550mm X 400mm including cutting for and pinning in ends of brackets or erecting stand including waste fittings, 32 mm bore PVC flush pipe with long screwed shucks and fly nuts and including PVC discharge pipe complete all as specified and directed.

S & F in repair 10 litres capacity PVC low level flushing cistern,syphonic action, valveless, with inlet, ball valve , float valve, handle etc fixed to wall with bracket and screwed including 32 mm bore PVC flush pipe complete fitting including taking out unserviceable flushing cistern and flush pipe etc. complete all as specified and directed.

S&F in repair 15 mm size PVC connection with PTMT nuts of length 600 mm long complete all as specified and directed.

S&F in repair 100mm size brass chromium plated shower rose swivel type complete all as specified and directed.

S&F in repair sinks made out of 1mm thick of stainless steel kitchen or laboratory with plugs, washers; including waste coupling with pipe, bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 495 mm x 420mm bowl size 410mmx330mmx160mm complete all as specified and directed.

S & F in repair sinks with drainage board made of 1mm thick stainless steel kitchen or laboratory with plugs, washers; including waste coupling with pipe, bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915 mm x 460mm bowl size 410mmx330mmx160mm complete all as specified and directed.

S&F in repair stainless steel kitchen plate rack made out of 1 mm thick of size not lessthan 900 mm x 750 mm fixed with stainless steel screw complete all as specified and directed.

S&F in repair 15mm bore angular/stop cock, cast copper alloy chromium plated fancy type screwed down high presure with crutch or butterfly handle, screwed both ends for iron pipe or unions complete all as specified and directed.

S & F in repair 20 mm bore gun metal, globe or gate valve with Iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F in repair 15mm bore bib taps cast copper chromium platedwith crutch or butter fly handle fency type complete all as specified and directed.

S&F in repair 15mm bore concealed type stop valves, cast copper alloy , chroimum plated screwed down high pressure with capstan head handle screwed both ends for iron pipe complete all as specified and directed.

S&F in repairs 15mm bore pillar taps cast copper alloy chromium plated fancy type with capston head screwed down high pressure with or without lettered “hot or cold” with long screwed shank and fly nuts for iron pipes complete all as specified and directed.

S&F in repair 15mm bore chromium plated brass mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.

S&F in repair CP health faucet including flexible pipe 1.0 to 1.5 Rm length and anodised hanging device complete all as specified and directed.

S&F in repairs 20mm dia D type tubular tower rail 60 cm long Aluminium anodised between flanges complete all as specified and directed.

S&F in repairs 600x450mm beveled edges mirror of slected quality mounted on 6mm thick plywood fixed to wooden plugs with CP brass screws complete all as specified and directed.

S&F15 mm bore steel water tubing `medium grade’ galvanized with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified & directed.

S&F 20 mm bore steel water tubing `medium grade’ galvanized with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified & directed.

Refix using old retrived 15 mm bore steel water tubing `medium grade’ galvanized with all new fittings and fixed complete to walls and ceiling or laid in floors complete all as specified & directed.

Refix using old retrived 20 mm bore steel water tubing `medium grade’ galvanized with all new fittings complete to walls and ceiling or laid in floors complete all as specified & directed.

S&F 20mm bore ball brass valves , high pressure, with polytheene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair complete all as specified and directed.

Cleaning and removing all sluge, mud, scale and dirt with bleaching powder from tanks and form mouths of circulating pipes, etc water tank capacity from 500 litre but not exceeding 1000 litre and writing the date of cleaning with synthetic enamel paints complete all as specified and directed

S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), double layered, ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including 20mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking down existing water storage tank complete all as specified and directed.

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks(cylindrical vertical with closed top, double layered ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including 20mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking down existing water storage tank complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to walls including digging and making good as existing complete all as specified and directed.

S & F in repair 75mm oulet PVC (SWR) floor trap outlet plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) bend any radius with access door complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) Junction single (Single T) equal or unequal with access door complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) Junction single (Single Y) equal or unequal with access door complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches/floor or fixed to walls including digging and making good as existing complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) bend any radius with access door complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) Junction single (Single T) equal or unequal with access door complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair Stack clamps out of 50 mm by 5 mm flat iron and 16 mmm dia round iron stays.including bolts and nuts and securing ends of stays to wall or roof in dia 110mm pipe complete all as specified and directed.

S&F in repair Stack clamps out of 50 mm by 5 mm flat iron and 16 mmm dia round iron stays.including bolts and nuts and securing ends of stays to wall or roof in dia 75 mm pipe complete all as specified and directed.

M&L for 10mm thick screed bed or bedding layer in cement mrortar(1:3) mixed with integral water proofing compound as per manufacturer's instructionsr over the padding concrete whilst the concrete surface is green, finished fair and even ( WPC will be measured and paid separately under separate item) complete all as specified and directed.

M&L for priming over roof surface with bitumen primer @0.25 Ltr/Sqm Over a cleaned roof surface and applying one coat of bitumen painting with hot blown grade bitumen 85/25 @1.20 kg/sqm and five layered Atactic Polypropylene modified polymeric membrane of minimum 3 mm thick reinforced with polyster non woven fabric matt (weight not less than 150 gm/sqm),laid with LPG torch application and a coat of aluminium primer @100 gm/ sqm on top ,including sealing all joints by thermo fusion, complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-O using 12.5mm graded stone aggregate as in Roof padding,fillup undulation,roof kerbs of mud stops or similar work maintain proper slope as required complete all as specified and directed.

M&L for 75mm thick cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in plinth protection and provided joints 10 mm wide & full depth at 3 m distance and every change of direction filled with sand and bituminious mix (1:3) complete all as specified and directed.

M&L for salt glazed stone ware gully trap size 150x150mm, square,type 'P' including setting and jointing to drains with cement mortar 1:1 and CI grating including demolition of existing traps complete all as specified and directed

M&L for plain cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type C-2 using 20 mm graded stone aggregate as cast in situ in plinth courses, parapets, copings, bed plates, surface channels, drains and the like including weathering, slightly rounded or chamfered angles & throating and use of form work complete all as specified and directed.

M&L for plain cement conctere (1:2:4) type B-1 using 20 mm graded stone aggregate as in the manhole etc. complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement conrete ,using extra cement, including forms, moulds ,mitred/stopped ends etc. complete all as specified and directed.

M&L 15mm thick rendering in cement mortar (1:4) on fair faces of brick or concrete surfaces with using water proofing compound , finished even and smooth without using extra cement complete all as specified and directed. Note:- Water proofing compound shall be measured and paid separately at supply rate only.

M&L for 150mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed.

M&L for plain cemet concrete (1:4:8) type D2 using 40 mm graded stone aggregate as in concrete bed to drain pipes including packing under and haunching against the sides of pipes as per SSR-I after they are laid and tested for pipes of 150 mm bore complete all as specified and directed.

Providing precast cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in man hole covers set in cement mortar (1:4) complete all as specified and directed.

Taking down carefully aluminium point wiring on wooden battens/through conduit (light fan, socket or power) complete with fittings such as switches, wooden batten, ceiling roses, pendants, regulators, box type tube light fittings, removing the materials from site except fittings etc which shall be reused in the work and making good the disturbed surfaces of walls/ceiling/ floors etc complete all as specified and directed.

M&L for point wiring for controlled by one switch with PVC insulated but unsheathed single core FRLS multistranded copper conductor cable IS-694 marked of size 1.5 Sqmm (nominal area) (Phase and Neutral) in and including non metallic rigid PVC conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in cement mortar (1:3) and to the original specification and PVC conduit on ceiling for steel structure/surface conduit with clamps, gutties etc for RCC ceiling for one light point controlled by one, one way switch including one run of PVC insulated FRLS copper conductor cable of size 1.5 Sqmm with green insulation as earth wire and connected to earth dolly complete all as specified and directed.

All as per Serial Item No. 124 here-in-before but for one fan point controlled by one, one way switch complete all as specified and directed.

All as per Serial Item No. 124 here-in-before but for one socket outlet 3 Pin, 6 Amp on independent board complete all as specified and directed.

All as per Serial Item No. 124 here-in-before but for one socket outlet 3 Pin, 6 Amp on same board complete all as specified and directed.

All as per Serial Item No. 124 here-in-before but for one bell point controlled by one bell push complete all as specified and directed.

M&L for point wiring for controlled by one switch with PVC unsheathed single core multistranded copper conductor cable of size 4.00 Sqmm (nominal area) in and including PVC conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in CM 1:3 and to the original specification and PVC cassing capping on ceiling for steel structure/surface conduit with clamps, gutties etc for RCC ceiling with including cast iron/pressed steel terminal/wooden boxes(as per site requirment) including providing new 3 mm thick plastic laminated sheet cover (Hylem) including one run of PVC insulated FRLS copper conductor cable of 4.00 Sqmm with green insulation as earth dolly for 6 pin, 16 Amp socket outlet on Independent board complete all as specified and directed.

S&F bell multi music type, AC 230 Volts, single pole (ISI Marked) complete all as specified and directed.

S&F Modular switch 6 Amp 250 V AC one way one module Cat part No 573450 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave) complete all as specified and directed.

S&F Modular switch 20 Amp 250 V AC one way with indicator one module Cat part No 572063 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave) complete all as specified and directed.

S&F Modular Socket, 6A - 2/3 pin combined 2 module cat Part No 573470 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave) complete all as specified and directed.

S&F Modular Socket 6A/16A - 2/3 pin combined 2 module cat part No 573471 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave) complete all as specified and directed.

S&F modular Fan regulator step type, 120W - 2 module cat part No 573463 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave) complete all as specified and directed.

S&F Metal flush mounting box of 1/2 Module complete all as specified and as directed. Cat part No 689007 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F Metal flush mounting box of 3 Module complete all as specified and as directed. Cat part No 689008 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F Metal flush mounting box of 4 Module complete all as specified and as directed. Cat part No 689009 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F Metal flush mounting box of 6 Module complete all as specified and as directed. Cat part No 689009 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F Metal flush mounting box of 8 Module complete all as specified and as directed. Cat part No 689042 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F Metal flush mounting box of 12 Module complete all as specified and as directed. Cat part No 689011 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F white colour modular blanking plate, one module i complete all as specified and directed.cat part No 573649 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F white colour plates with frame for modular switch of 01 module complete all as specified and as directed.Cat Part No 575700 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F white colour plates with frame for modular switch and socket of 03 module complete all as specified and as directed.Cat Part No 575720 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F white colour plates with frame for modular switch and socket of 04 module complete all as specified and as directed.Cat Part No 575730 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F white colour plates with frame for modular switch and socket of 06 module complete all as specified and as directed.Cat Part No 575740 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F white colour plates with frame for modular switch and socket of 08 module complete all as specified and as directed.Cat Part No 575750 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F white colour plates with frame for modular switch and socket of 2 x 6 module complete all as specified and as directed.Cat Part No 575770 of Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

S&F ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC/Polycarbonate,isolated body (ISI Marked) complete all as specified and directed.

S&F in replacement 10 W LED Bulk head fitting in engineering plastic housing with clear prismatic diffuser cat part No LBHP-10-CDL of make : CG or equivalent in Syska/Philips/Bajaj including LED 10 W complete with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 complete all as specified and directed.

S&F in replacement submain wiring with 2 single core PVC insulated unsheathed multi stranded copper conductor FRLS wire 6.00 Sq mm 1100 volts grade including and 6.00 Sq mm PVC insulated, multi stranded, unsheathed copper wire green in colour as earthing lead drawn through in PVC casing caping conduit complete all as specified and directed. Note : Two run of 6.0 Sqmm cable and one run of 6.0 Sqmm cable as earth continuity conductor shall be measured & paid as one unit.

S&F in replacement submain wiring with 2 single core PVC insulated unsheathed multi stranded copper conductor FRLS wire 4.00 Sq mm 1100 volts grade including and 4 Sq mm PVC insulated, multi stranded, unsheathed copper wire green in colour as earthing lead drawn through in PVC casing caping conduit complete all as specified and directed. Note : Two run of 4.00 Sqmm cable and one run of 4 Sqmm cable as earth continuity conductor and 25 mm PVC conduit shall be measured & paid as one unit.

S&F in replacement submain wiring with 2 single core PVC insulated unsheathed multi stranded copper conductor FRLS wire 2.50 Sq mm 1100 volts grade including and 2.50 Sq mm PVC insulated, multi stranded, unsheathed copper wire green in colour as earthing lead drawn through in PVC casing complete all as specified and directed. Note : Two run of 2.50 Sqmm cable and one run of 2.50 Sqmm cable as earth continuity conductor and 25 mm PVC conduit shall be measured & paid as one unit.

S&F in replacement MCB, SP, 6 to 32 Amp, 240 V, 10 KA rupturing caoacity complete all as specified and directed.

S&F in replacement MCB, SPN, 40 Amp to 63, 240 V, 10 KA rupturing capacity complete all as specified and directed.

S&F in replacement MCB, TP, 63 Amp, 240 V, 10KA rupturing capacity complete all as specified and directed.

S&F in replacement 300mm sweep heavy duty exhaust fan steel body AC single phase 230 V with three baldes including making holes in to the wall as per fan size and making good the disturved surfaces all as directed complete all as specified and directed.

S&F in replacement ceiling fan of sweep 1200 mm, steel body, AC single phase 230 V, with squirrel cage induction motor with three baldes and with 300 mm down road pre-wired and incuding connecting up with twin core twisted flexible copper conductor with suitable hanging arrangement and fan regulator complete all as specified and directed.

S&F in replacement Surface and wall mounted LED tube light fittings of cap 9W , Two feet Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver with cat part no- LHEXBLP7IN1W009 of havells or equivallent in CG/Philip/Bajaj complete all as specified and directed.

S&F in replacement lamp holder angular type,PVC/Polycarbonate type with back plate suitable for batten fiitng complete all as specified and directed.

S&F in replacement LED ball lamp 10 W of cat part no. LHLDEUEBML8Z010 of Havells or equivallent in Philips/Bajaj/CG complete all as specified and directed.

S&F in replacement Decorative, wall mounting fixture, in durable plastic body & designer mesh in gold finish suitable for 14 W LED ball lamp with cat part no-LHFOECE1TZ1B014 of Havells equivallent in Philips/Bajaj/CG complete all as specified and directed.

S&F in replacement surface and wall mounted LED tube light fittings of cap 20W , four feet Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver with cat part no- LHEXBACP7IN1W020 of havells or equivallent in CG/Philip/Bajaj complete all as specified and directed.

S&F in replacement Prewired Distribution Board factory made sheet metal enclosure double door distribution board class IP-43 IK 09 with 200 Amp rated copper bus bar 240 Volts 8 way (2 + 6 way) single pole and neutral link complete all as specified and directed.

S&F in replacement Prewired Distribution Board factory made sheet metal enclosure double door distribution board class IP-43 IK 09 with 200 Amp rated copper bus bar 240 Volts 12 way (2 + 10 way) single pole and neutral link complete all as specified and directed.

S&F in replacement and connecting LED street light fittings on high mast poles pressue die cast housing with IP 66 protection high resistant tempered glass for protection with 10KV surge protection applicable for large area lighting with efficient high output emitter LED for better distribution or capacity 60 watt (110LM/W ) complete all as specified and directed. Make : Cat Part no.LSTP-60-CDL-M of Crompton Greaves or equivalent in Orient/Wipro.

M&L for sand cushioning of under ground cable provided with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and directed. Note:- 18cm punned thickness shall be consideredfor measurement and payment.

M&L for 40 to 50mm thick stone patti rough dressed jodhpur stone slab cover laid in trenches for protection of cable 25 to 30 cm wide and not less then 50cm in length laid dry abutting each other with gap between adjecent slab not excedding 10 mm over sand cushoing complete all as specified and directed.

S& F modular fan regulator 120 W, 2 modules complete all as specified and directed.

Supply,lay in trenches, joint, test and commission in replacement cable XLPE insulated heavy duty electric cable with aluminium conductors 1100 Volt grade, cross sectional area 25 Sqmm 4 Core including fixing on walls and poles, passing though ducts complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick surrounded with charcoal and salt, buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as specified and directed. Notes: (i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) Item includes the cost of 7.50m GI pipe for protection of earth wire/strip Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.50m earth lead wire/strip. Any variation in length shall be adjusted through deviation order. (iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate.

Supply, install, test and commission in replacement; LT panel size 800 mm x 600 mm x 150 mm enclosures cubical weather and vermin proof totally enclosed made out of 1.6 mm thick CRCA sheet machine pressed of suitable size to operate on 3 phase 4 wire system 415 Volts, 50HZ double door with front openable and PVC acrulic glass cover suitable size for checking of meter reading without opening door with locking arrangement incl inner shutters for mounting switch gear etc, suitable arrangement for fixing of electrical meter and SPN 40 to 63 Amp including pre wiring from Bus bar to Meter and Meter to MCB SPN (for pre wiring use 6.00 Sqmm Single core copper cable and suitable size of lugs for connecting from Busbar to meter and meter to MCB SPN)including bottom gland plate with sufficient numbers of circular cable entry holes, including prewired complete as per drawing with masonary work for fixing in wall duly powder coated with comprising of the following :- INCOMING :- (i) MCCB 63 Amps FP, 415 Volt 25 KA adjustable thermal & fixed magnetic setting Ics = 100% = 01 No (ii) Phase indicating lamp LED type with HRC fuse – 1 Set of three. (iii) ON/OFF indicating lamp on incomer feeder for status of feeder = 02 Nos (iii) Aluminium bus bar 200 Amps capacity with bus bar supports, DMC/SMC insulators of CPRI approved of suitable length insulated heavy heat shrinkable sleeves etc -04 Nos. OUT GOING (i) MCB 32 Amp,415 Volt,10 KA, Single pole and neutral -04 Nos. (ii) S&F single phase electronic energy meter with LCD display of rating 5-30 Amp class 1.0, 240V 50 Hz counter type display with transparent hinge including connection from SPN to meter with 6 Sqmm copper stranded conductor including earth wire complete all as specified and directed. - 04 Nos

M/S VISHNOI ENTERPRISES

M/s RKG CONSTRUCTIONS

S K TRADER

Dadhich Engineers