Construction of TAMS (Transmission Asset Management System) Building at DVC Substation, Maithon.

BOQ DVC Maithon

NAME OF WORK:CONSTRUCTION OF TWO STOREYED SWITCH YARD AND CONTRIOL ROOM TAMS BUILDING

AT DVC MAITHON SUBSTATION

TAMS BUILDING (G+2), BOQ - CIVIL WORKS

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

A 2.0 EARTH WORKS

Earth work in excavation by mechanical means (Hydraulic

excavator)/manual means over areas (exceeding 30 cm in depth, 1.5

1 2.6 m in width as well as 10 sqm on plan) including getting out and

disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as

directed by Engineer-in-charge.

i 2.6.1 All kinds of soils Cum 3428.96 177.50 608,640.79

Extra for every additional lift of 1.5 m or part thereof in excavation /

banking excavated or stacked materials.

Filling available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc. in layers not exceeding 20cm in depth,

3 2.25 consolidating each deposited layer by ramming and watering, lead Cum 3592.10 196.00 704,051.80

up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including

4 2.27 watering, ramming, consolidating and dressing complete. Cum 495.59 2,123.75 1,052,514.75

Surface dressing of the ground including removing vegetation and

5 2.28 inequalities not exceeding 15 cm deep and disposal of rubbish, lead

up to 50 m and lift up to 1.5 m.

i 2.28.1 All kinds of soil Sqm 2038.25 34.15 69,606.24

Clearing jungle including uprooting of rank vegetation, grass, brush

wood, trees and saplings of girth up to 30 cm measured at a height

6 2.31 of 1 m above ground level and removal of rubbish up to a distance sqm 2038.25 17.60 35,873.20

of 50 m outside the periphery of the area cleared.

Providing and injecting chemical for pre constructional anti - termite

treatment and creating and chemical barrier under and around the

column pits wall trenches basement excavation top surface if plinth

filling junction of wall and floor, along the external permeter of

binding expansion joints surrounding of pipes and condult

7 etc.complete (plinth area of the building at ground floor only shall

be measured as per I.S 6313 (part 2 1981). Aldrine emulsifiable

concentrate or any other approved material such as Hepthachlor of

CHlordane will be used. The rate of application of chemical emultion

shall be as follows :=

i i (1) Treatment for masonry and foundation 5 liters per Sqm

(2) Back fill in immediate contact with foundation 7.5 liters per Sqm

iii iii (3) Treatment of top surface of plinth filling 5 liters per Sqm.

(4) Treatment of soil along external per meter of building 7.50 liters

iv iv per Sqm.

(5) Treatment of soil under apron along external per meter 5 liter

TOTAL (Carried Over to Summary of Civil Works) 3,032,918.05 -

B 4.0 CONCRETE WORKS

Providing and laying in position cement concrete of specified grade

1 4.1 excluding the cost of centering and shuttering - All work up to plinth

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural

a 4.1.6 sources : 6 graded stone aggregate 40 mm nominal size derived Cum 1.00 7,178.75 7,178.75

from natural sources)

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural

b 4.1.8 sources : 8 graded stone aggregate 40 mm nominal size derived Cum 244.08 6,812.00 1,662,657.80

from natural sources)

Providing and laying cement concrete in retaining walls, return walls,

walls (any thickness) including attached pilasters, columns, piers,

abutments, pillars, posts, struts, buttresses, string or lacing courses,

2 4.2 parapets, coping, bed blocks, anchor blocks, plain window sills,

fillets, sunken floor etc., up to floor five level, excluding the cost of

centering, shuttering and finishing:

1:1½:3 (1 cement : 1½ coarse sand (zone-III) derived from natural

i 4.2.2 sources : 3 graded stone aggregate 20 mm nominal size derived Cum 5.23 10,357.55 54,221.48

from natural sources).

1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural

ii 4.2.5 sources : 6 graded stone aggregate 20 mm nominal size derived Cum 2.20 9,311.40 20,496.72

from natural sources)

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Centering and shuttering including strutting, propping etc. and

removal of form work for :

i 4.3.1 Foundations, footings, bases for columns. Sqm 247.00 392.15 96,861.05

Providing and laying damp-proof course 50mm thick with cement

concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from

natural sources : 4 graded stone aggregate 20mm nominal size

derived from natural sources).

Extra for providing and mixing water proofing material in cement

4 4.12 concrete work in doses by weight of cement as per manufacturer's 55.00 18.15 998.25

Providing & applying a coat of residual petroleum bitumen of grade

of VG-10 of approved quality using 1.7kg per square metre on damp

5 4.13 proof course after cleaning the surface with brushes and finally with Sqm 172.00 146.15 25,137.80

a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1

cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm

nominal size) over 75mm thick bed of dry brick ballast 40 mm

6 4.17 nominal size, well rammed and consolidated and grouted with fine Sqm 189.43 749.30 141,941.40

sand, including necessary excavation, levelling & dressing & finishing

the top smooth.

TOTAL (Carried Over to Summary of Civil Works) 2,094,762.25 -

C 5.0 REINFORCED CEMENT CONCRETE WORK

Centering and shuttering including strutting, propping etc. and

removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses,plinth

and string courses etc.

Suspended floors, roofs, landings, balconies and access platform.

d 5.9.4 Shelves (Cast in situ) Sqm 22.58 927.25 20,936.56

Lintels, beams, plinth beams, girders, bressumers and cantilevers

f 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 2796.43 961.30 2,688,204.55

g 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 261.49 764.95 200,022.95

h 5.9.8 Spiral staircases (including landing) Sqm 0.00 798.35 -

i 5.9.9 Arches, domes, vaults up to 6 m span Sqm 5.00 2,154.35 10,771.75

Small lintels not exceeding 1.5m clear span, moulding as in cornices,

j 5.9.15 window sills, string courses, bands, copings, bed plates, anchor Sqm 25.97 392.15 10,183.72

blocks and the like.

k 5.9.16 Edges of slabs and breaks in floors and walls

l 5.9.19 Weather shade, Chajjas, corbels etc., including edges. Sqm 10.00 951.10 9,511.00

Extra for additional height in centering, shuttering where ever

required with adequate bracing, propping etc., including cost of de-

2 5.11 shuttering and decentering at all levels, over a height of 3.5 m, for

every additional height of 1 metre or part thereof (Plan area to be

Suspended floors, roofs, landing, beams and balconies

(Plan area to be measured)

Steel reinforcement for R.C.C. work including straightening, cutting,

3 5.22 bending, placing in position and binding all complete upto plinth

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting,

4 5.22A bending, placing in position and binding all complete above plinth

Thermo-Mechanically Treated bars of grade Fe-500D or more.

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Providing and laying in position ready mixed or site batched design

mix cement concrete for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived from natural sources,

Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to

accelerate / retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of

concrete to site of laying, curing, carriage for all leads; but excluding

5 5.33.1 the cost of centering, shuttering, finishing and reinforcement as per

direction of the engineer-in-charge; for the following grades of

concrete. Note: Extra cement up to 10% of the minimum specified

cement content in design mix shall be payable separately. In case

the cement content in design mix is more than 110% of the specified

minimum cement content, the contractor shall have discretion to

either re-design the mix or bear the cost of extra cement.

a) 5.33.1 All works upto plinth level.

Concrete of M30 grade with minimum cement content of 350 kg

b) 5.33.2 All works above plinth level upto floor V level.

Concrete of M30 grade with minimum cement content of 350 kg

Add for using extra cement in the items of design mix over and

above the specified cement content therein.

Providing and fixing of expansion joint system related with floor

location as per drawings and direction of Engineer-In-Charge. The

joints system will be of extruded aluminum base members, self

aligning / self centering arrangement and support plates etc. as per

ASTM B221-02. The system shall be such that it provides floor to

floor /floor to wall expansion control system for various vertical

localtion in load application areas that accommodates multi

directional seismic movement without stress to it's components.

System shall consist of metal profiles with a universal aluminum

base member designed to accommodate various project conditions

and finish floor treatments. The cover plate shall be designed of

width and thickness required to satisfy projects movement and

5.44 loading requirements and secured to base members by utilizing

manufacturer’s pre-engineered self- centering arrangement that

freely rotates / moves in all directions. The Self - centering

arrangement shall exhibit circular sphere ends that lock and slide

inside the corresponding aluminum extrusion cavity to allow

freedom of movement and flexure in all directions including vertical

displacement. Provision of Moisture Barrier Membrane in the Joint

System to have watertight joint is mandatory requirement all as per

the manufactures design and as approved by Engineer -in- Charge.

(Material shall confirm to ASTM 6063).

Providing and fixing of expansion joint system related with wall joint

(internal/external) location as per drawings and direction of

Engineer-In- Charge. The joints shall be of extruded aluminum base

members, self aligning / centering arrangement and support plates

as per ASTM B221- 02. The material shall be such that it provides an

Expansion Joints System suitable for vertical wall to wall/ wall to

corner application, both new and existing construction in office

Buildings & complexes with no slipping down tendency amongst the

components of the Joint System. The Joint System shall utilize light

weight aluminum profiles exhibiting minimal exposed aluminum

surfaces mechanically snap locking the multicellular to facilitate

movement. (Material shall confirm to ASTM 6063).

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Providing and fixing of expansion joint system of approved make and

manufactures for various roof locations as per approved drawings

and direction of Engineer-In-Charge. The joints shall be of extruded

aluminum base members with, self aligning and self centering

arragement support plates asper ASTM B221-02. The system shall be

such that it provides watertight roof to roof/roof to corner joint

cover expansion control system that is capable of accommodating

multidirectional seismic movement without stress to its

components. System shall consist of metal profile that incorporates

a universal aluminum base member designed to accommodate

various project conditions and roof treatments. The cover plate shall

be designed of width and thickness required to satisfy movement

and loading requirements and secured to base members by utilizing

5.46 manufacturer’s pre-engineered self-centering arrangement that

freely rotates / moves in all directions. The Self centering

arrangement shall exhibit circular sphere ends that lock and slide

inside the corresponding aluminum extrusion cavity to allow

freedom of movement and flexure in all directions including vertical

displacement. The Joint System shall resists damage or deterioration

from the impact of falling ice, exposure to UV, airborne

contaminants and occasional foot traffic from maintenance

personnel. Provision of Moisture Barrier Membrane in the Joint

System to have water tight joint is mandatory requirement.

(Material shall confirm to ASTM 6063).

TOTAL (Carried Over to Summary of Civil Works) 57,771,762.72 -

D 6.0 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in foundation and plinth in:

i 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 24.25 7,132.25 172,963.75

Brick work with non modular fly ash bricks conforming to IS:12894,

2 6.34 class designation 10 average compressive strength in super structure

above plinth level up to floor V level in :

i 6.34.2 Cement mortar 1:6 (1 cement : 6 Coarse sand) Cum 691.46 8,752.55 6,052,027.28

Half brick masonry with non modular fly ash bricks of class

3 6.45 designation 10, conformingio IS :12894, in super structure above

plinth and upto floor V level.

i 6.45.2 Cement mortar 1 : 4 (1 cement : 4 coarse sand) Sqm 730.99 1,105.80 808,324.87

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars

at every third course of half brick masonry.

Brick edging 7cm wide 11.4 cm deep to plinth protection with

common burnt clay F.P.S. (non modular) bricks of class designation

7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine

TOTAL (Carried Over to Summary of Civil Works) 7,121,847.77 -

E 8.0 MARBLE & GRANITE WORK

Providing and fixing 18mm thick gang saw cut ( premoulded and

prepolished) machine cut for kitchen platforms, vanity counters,

window sills , facias and similar locations of required size of

approved shade, colour and texture laid over 20mm thick base

1 8.2 cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated

with white cement, mixed with matching pigment, epoxy touch ups,

including rubbing, curing, moulding and polishing to edge to give

high gloss finish etc. complete at all levels.

a) 8.2.2 Granite of any colour and shade

ii 8.2.2.2 Area of slab over 0.50 sqm Sqm 22.58 5,136.30 115,973.54

Extra for fixing marble / granite stone over and above corresponding

basic item, in facia and drops of width upto 150mm with epoxy resin

baesd adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash

basins/ kitchen sink in kitchen platform, vanity counters and similar

3 8.5 location in marble/Granite/Stone work including necessary holes for each 27 978.70 26,424.90

pillar taps etc. including rubbing and polishing of cut edge etc.

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Providing and fixing stone slab with table rubbed, edges rounded

and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal

partitions by cutting a chase of appropriate width with chase cutter

and embedding the stone in the chase with epoxy grout or with

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 6 mm nominal size) as per direction of Engineer-in-charge

and finished smooth. Granite Stone of approved shade

Providing and fixing machine cut, mirror / eggshell polished , Granite

stone work for wall lining (veneer work) including dado, skirting,

risers of steps etc., in required design and pattern wherever

Derived required, stones of different finished surface texture, on 12 mm

Rate DSR- (average) thick cement mortar 1:3 (1 cement : 3 oarse sand) laid and

5 2023 jointed with white cement slurry @ 3.3 kg/Sq.Mt. including pointing Sqm. 189.00 8,625.70 1,630,293.10

(Refer with white cement slurry admixed with pigment of matching shade,

,8.11) including rubbing, curing, polishing etc. all complete as per

Architectural drawings, and as directed by the Engineer-in-Charge. a.

18 mm thick Granite stone slab any colour etc.

Providing and fixing Ist quality ceramic glazed wall tiles conforming

to IS: 15622 (thickness to be specified by the manufacturer), of

approved make, in all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-Charge, in skirting,

6 8.31 risers of steps and dados, over 12 mm thick bed of cement mortar Sqm 647.35 1,267.95 820,813.01

1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry

@ 3.3kg per sqm, including pointing in white cement mixed with

pigment of matching shade complete.

TOTAL (Carried Over to Summary of Civil Works) 2,869,639.56 -

F 9.0 WOOD & PVC WORK

Providing and fixing ISI marked flush door shutters conforming to IS :

2202 (Part I) non-decorative type, core of block board construction

with frame of 1st class hard wood and well matched commercial 3

ply veneering with vertical grains or cross bands and face veneers on

both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm

2 9.23 minimum depth on all edges of flush door shutters (over all area of Sqm 213.98 462.35 98,931.34

door shutter to be measured).

Providing and fixing wooden moulded beading to door and window

frames with iron screws, plugs and priming coat on unexposed

surface etc. complete :2nd class teak wood.50x12 mm.

Providing and fixing M.S. grills of required pattern in frames of

windows etc. with M.S. flats, square or round bars etc. including

4 9.48.2 priming coat with approved steel primer all complete.Fixed to Kg 3559.68 238.35 848,449.73

openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium tower bolts, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868 )

transparent or dyed to required colour or shade, with necessary

screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or shade, with necessary

screws etc. complete :

Providing & Fixing decorative high pressure laminated sheet of plain

/ wood grain in gloss / matt / suede finish with high density

7 9.127 protective surface layer and reverse side of adhesive bonding quality

conforming to IS : 2046 Type S, including cost of adhesive of

approved quality.

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Providing and fixing factory made uPVC glazed/wire mesh windows/

doors comprising of lead free uPVC multi-chambered frame, sash

and mullion/coupler (wherever required) extruded profiles having

minimum wall thickness of 1.70 mm for Series R1 and R2 profiles

and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608

in any shape, colour and design duly reinforced with galvanized mild

steel section made of required shape & size as per CPWD

Specification, uPVC extruded glazing beads, interlocks and Inline

sash adaptor (where ever required) of appropriate dimension, EPDM

gasket, hardware, SS 304 garde fastteners of minimum 8 mm dia

with countersunk head, comprising of matching polymade PA6 grade

sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14,

8 9.147A plastic packers, plastic caps and necessary stainless steel screws etc.

Profile of frame, sash & mullion (if required) shall be mitred cut and

fusion welded/ mechanically jointed duly sealed at all corners,

including drilling of holes for fixing hardware and drainage of water

etc. After fixing frame the gap between frame and adjacent finished

wall shall be filled with weather proof silicon sealent over backer rod

of approved size and quality, all complete as per approved drawing

conforming to CPWD specification & direction of Engineer-in-charge.

Section of steel reinforcement and cross sections of uPVC profiles to

be as per design approved by Engineer-in-charge.

Wire mesh / Glazing of plain / toughned/ laminated/ double glass

unit with / without high performance coatings as per design

requirments and conforming to IS: 3548 & IS: 16231 shall be paid

Note:- Structural design proof checked from a Government

Engineering Institute, to be provided by the manufaturer for :

(i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3

(ii) Sites with structure height more than 20m for all wind speeds

Three track three panels sliding window with two glazed & one wire

9.147.A4 mesh panels with Aluminium channel for roller track, wool pile,

nylon rollers with SS 304 body.

Using R3 series with frame (98 mm & abobe) x (40 mm & above) &

both glazed and fly screen sash (30 mm & above) x (55 mm & above)

i 9.147.A4.2 with zinc alloy (zamak) powder coated handle on every glazed panel Sqm 222.48 10,874.20 2,419,292.02

along with multi-point locking system. (Height upto 1.8m).

Providing and fixing non load bearing fixed frame for fire resistant

glazed partition for 120 minutes Fire Rating, made out to a profile of

dimension 60mm x 70 mm of 1.6 mm thick galvanised steel sheet as

per test evidence suitable for fixing fire rated glass for 120 minutes

of both integrity & radiation control (EW120) & minimum 20

minutes of insulation (EI20).The profile has to be fixed to the

supporting construction by means of anchor fasteners of size M10 x

80, every 150 mm from the edges and every 500 mm (approx) c/c.

Linear measurement of frame shall be measured for payment. The

frame shall be filled with mineral wool insulation of density

minimum 96kg/ cum. and finished with a approved fire resistant

primer or Powder coating of not less than 30 micron in desired

shade as per NBC 2016, IS 16231 (Part 3):2016 and directions of

Engineer - in- Charge.

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Providing and fixing glazing in fire resistant door shutters, fixed

panels & partitions etc., with G.I. beading made out of 1.6 mm thick

G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm

screwed with M4 x 38 mm SS screws at distance 75 mm from the

edges and 150 mm c/c , including applying a coat of approved fire

resistant primer/ powder coating of not less than 30 micron on G.I.

beading, & special ceramic tape of 5 x 20 mm size etc complete in all

respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction

of Engineer-in-charge with glass of required thickness having 120

minutes of fire resistance both integrity & radiation control (EW120)

10 9.164 and minimum 20 minutes of insulation (EI20). The manufacturer Sqm 30.24 43,677.65 1,320,812.14

have to give test report/certification of fire glass and the glass

should have the stamp showing the value of E, EW & EI. The glass

shall be tested in approved NABL accredited lab or by any other

accreditation body which operates in accordance with ISO/IEC 17011

and accredits labs as per ISO/IEC 17025 for testing and calibration

scopes shall be eligible. The maximum glazing size shall not be more

than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing approved brand and manufacture of Rack and

pinion door closer TS 68 EN size 2/3/4, with std. arm and with two

independent closing valves and latching speed adjustable by arm.

11 MR-1 Silver finish. As per EN 1154. Each 103 2,910.00 299,730.00

Approved Make : dormakaba / Hafele / GEZE with necessary

accessories and screws etc. complete in all respects as per

manufacture ofrs' specificatios & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture of 4012 wall

mounted door stop dome with 60mm length with fixing accessories

12 MR-2 Approved Make : dormakaba / Hafele / GEZE with necessary Each 117 701.00 82,017.00

accessories and screws etc. complete in all respects as per

manufacture ofrs' specificatios & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture of Pure 8100

Type 3 Package with Pair of Pure 8100 Design Lever Handle on Roses

& escutcheons. Including 271a Sash lock with 72mm CTC, 55mm

Backset 20mm Square forend. EPC 60mm length oneside thumb turn

otherside coin release operation Approved Make : dormakaba /

Hafele / GEZE with necessary accessories and screws etc. complete

in all respects as per manufacture ofrs' specificatios & as directed by

Engineer-in-charge.

Providing and fixing approved brand and manufacture of Stainless

Steel Tower bolt 300 mm long with 10 mm dia ( TR 1210SS) along

14 MR-4 with necessary accessories and screws etc. complete in all respects Each 234 866.00 202,644.00

as per manufacture ofrs' specificatios & as directed by Engineer-in-

Providing and fixing approved brand and manufacture of Stainless

Steel Tower bolt 150 mm long with 10 mm dia ( TS 610SS) along with

15 MR-5 necessary accessories and screws etc. complete in all respects as per Each 10.0 566.00 5,660.00

manufacture ofrs' specificatios & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture of Stainless

Steel Door Buffer wall mounted 22 mm dia,75 mm long (DB (22)

16 MR-6 along with necessary accessories and screws etc. complete in all Each 117.00 523.00 61,191.00

respects as per manufacture ofrs' specificatios & as directed by

Engineer-in-charge.

Providing and fixing approved brand and manufacture of Stainless

Steel Handle 125 mm long with necessary accessories and screws

17 MR-7 etc. complete in all respects as per manufacture ofrs' specificatios & Each 234.00 699.00 163,566.00

as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture of Stainless

Steel Sliding Tower Bolt 300x16 mm long with necessary accessories

18 MR-8 and screws etc. complete in all respects as per manufacture ofrs' Each 256.00 1,004.00 257,024.00

specificatios & as directed by Engineer-in-charge.

Providing and fixing fly proof stainless steel grade 304 wire gauge, to

Derived windows, Doors and clerestory windows using wire gauge with

19 Item average width of aperture 1.4 mm in both directions with wire of Sqm 222.48 2,129.05 473,671.04

(9.135.2) dia. 0.50 mm all complete. With aluminium Snap beading.

Providing and fixing steel (white power coated) crescent lock for

20 9.153 uPVC / aluminium sliding window/ door with necessary screws etc. Each 182.00 198.30 36,090.60

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

TOTAL (Carried Over to Summary of Civil Works) 6,326,619.00 1,796,246.00

G 10.0 STEEL WORK

Providing and fixing pressed steel door frames conforming to IS:

4351, manufactured from commercial mild steel sheet of 1.60 mm

thickness, including hinges, jamb, lock jamb, bead and if required

angle threshold of mild steel angle of section 50x25 mm, or base ties

of 1.60 mm, pressed mild steel welded or rigidly fixed together by

mechanical means,

including M.S. pressed butt hinges 2.5 mm thick with mortar guards,

lock strike-plate and shock absorbers as specified and applying a

coat of approved steel primer after pre-treatment of the surface as

directed by Engineer-in-charge:

10.14.1 Profile B

10.14.1.1 Fixing with adjustable lugs with split end tail to each jamb metre 470.85 583.30 274,646.81

Steel work welded in built up sections/ framed work including

cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer using structural steel etc. as required

In stringers, treads, landings etc. of stair cases including use of

chequered plate wherever required, all complete.

In gratings, frames, guard bar, ladder, railings, brackets, gates and

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box

for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid

of 1.5 mm thick M.S. sheet with its top surface hacked for proper

bonding, top lid shall be screwed into the cast iron/ M.S. sheet box

by means of 3.3 mm dia round headed screws, one lock at the

corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape

as per standard drawing.

Providing and fixing carbon steel galvanised ( minimum coating 5

micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield

strength 480 N/mm2), counter sunk head, comprising of 10 m dia

polyamide PA 6 grade sleeve, including drilling of hole in frame ,

concrete/ masonry, etc. as per direction of Engineer-in-charge.

Providing and fixing stainless steel ( Grade 304) railing made of

Hollow tubes, channels, plates etc., including welding, grinding,

buffing, polishing and making curvature (wherever required) and

fitting the same with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary accessories & stainless

5 10.28 steel dash fasteners , stainless steel bolts etc., of required size, on KG 2124.27 772.40 1,640,786.15

the top of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-in-charge, (for payment

purpose only weight of stainless steel members shall be considered

excluding fixing accessories such as nuts, bolts, fasteners etc.)

Fabrication, supply and Installation of New clear line glass railing

system by Ozone made of Heavy duty aluminum U Type Hollow walls

Base channel ( HWBC) (OZRF-NCLSYS- HWBC-AL) AL-6063 grade with

mill finish of size 12.5mm( thick)72( wide)x122 mm( height). Glass

Specs. is 16.89mm thk (8mm CT+ .89SGP+8MM CT) to be GRIPPED

with fixing kit (OZRF-NCL-ACC-KIT-17MM) made of self-pushing

clamps ( SPC) made by hardened aluminum -6063 grade each at

maximum 350mm cc to cc . glass should be lifted from base by Solid

Nylon L Block separates at least 3 nos/ meters. HWBC to be fixed

with M12 GI stud chemically grouted. Glass should be fixed with

completely dry system so that in case of breakage it can be changed

without any silicon cutting and very fast as well.. exposed edges of

HWBC (if any) to be covered with SS 304 grade end caps. The Top

Edge of glass will be covered with SS 304 grade Round slotted tube

of Dia42x1.5 mm thk. fixed on the glass edge with EPDM gasket. The

Vertical joint of glass will be free from silicon. The total height of the

system will be max. 900 mm from ledge top, All top rail joints will be

joined by using argon welding only.

TOTAL (Carried Over to Summary of Civil Works) 1,998,928.65 167,675.25

H 11.0 FLOORING WORK

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Kota stone slab flooring over 20 mm (average) thick base laid over

and jointed with grey cement slurry mixed with pigment to match

1 11.26 the shade of the slab including rubbing and polishing complete with

base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and

pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3

2 11.27 coarse sand) and jointed with grey cement slurry mixed with sqm 5.00 2,354.70 11,773.50

pigment to match the shade of the slabs, including rubbing and

polishing complete.

Extra for pre finished nosing to treads of steps of marble stone.

Extra for marble stone flooring in treads of steps and risers using

single length up to 2.00 metre.

Providing and laying rectified Glazed Ceramic floor tiles of size

300x300 mm or more (thickness to be specified by the

manufacturer), of 1st quality conforming to IS : 15622, of approved

make, in all colours, shades, except White, Ivory, Grey, Fume Red

Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse

sand), jointing with grey cement slurry @ 3.3 kg/ sqm including

pointing the joints with white cement and matching pigments etc.,

Providing and laying Vitrified tiles in different sizes (thickness to be

specified by manufacturer), with water absorption less than 0.08 %

and conforming to I.S. 15622, of approved make, in all colours &

shade, in skirting, riser of steps, over 12 mm thick bed of cement

mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement

slurry @ 3.3 kg/ sqm including grouting the joint with white cement

& matching pigments etc. complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness

to be specified by the manufacturer) with water absorption less than

0.08% and conforming to IS:15622, of approved brand &

manufacturer, in all colours and shade, laid on 20 mm thick cement

mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement

slurry @3.3 kg/sqm including grouting the joints with white cement

and matching pigments etc. The tiles must be cut with the zero

chipping diamond cutter only . Laying of tiles will be done with the

notch trowel, plier, wedge, clips of required thickness, leveling

system and rubber mallet for placing the tiles gently and easily.

a) 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Providing and laying flamed finish Granite stone flooring in required

design and patterns, in linear as well as curvilinear portions of the

building all complete as per the architectural drawings with 18 mm

thick stone slab over 20 mm (average) thick base of cement mortar

1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry

7 11.55.1 and pointing with white cement slurry admixed with pigment of Sqm 1515.39 3,186.70 4,829,107.54

matching shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge

:Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown,

Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required

design and patterns, in linear as well as curvilinear portions of the

building all complete as per the architectural drawings with 18 mm

thick stone slab over 20 mm (average) thick base of cement mortar

1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry

8 11.56.1 and pointing with white cement slurry admixed with pigment of Sqm 189.00 4,481.30 846,984.30

matching shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black, Cherry/Ruby Red or

TOTAL (Carried Over to Summary of Civil Works) 8,186,916.51 -

I 12.0 ROOFING

Providing and laying gola 75x75mm in cement concrete M15 grade

1 12.21 including finishing with cement mortar 1:3 (1 cement : 3 fine sand) rmt. 1603.02 305.15 489,161.55

as per standard design in 75x75 mm deep chase.

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Making khurras 45x45 cm with average minimum thickness of 5 cm

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400

2 12.22 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse each 6.00 298.25 1,789.50

sand) and a coat of neat cement, rounding the edges and making

and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC RAIN

WATER PIPES conforming to IS : 13592 Type A including jointing with

seal ring conforming to IS : 5382 leaving 10 mm gap for thermal

expansion.(i) Single socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded

fittings/ accessories for unplasticised Rigid PVC rain water pipes

4 12.42 conforming to IS : 13592 Type A including jointing with seal ring

conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

a) 12.42.1 Coupler

c) 12.42.6 Shoe (Plain)

Providing and fixing tiled false ceiling of specified materials of size

595x595 mm in true horizontal level, suspended on inter locking

metal grid of hot dipped galvanized steel sections ( galvanized @ 120

grams/ sqm, both side inclusive) consisting of main "T" runner with

suitably spaced joints to get required length and of size 24x38 mm

made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm

center to center and cross "T" of size 24x25 mm made of 0.30 mm

thick (minimum) sheet, 1200 mm long spaced between main "T" at

600 mm center to center to form a grid of 1200x600 mm and

secondary cross "T" of length 600 mm and size 24x25 mm made of

0.30 mm thick (minimum) sheet to be interlocked at middle of the

1200x600 mm panel to form grids of 600x600 mm and wall angle of

size 24x24x0.3 mm and laying false ceiling tiles of approved texture

in the grid including, required cutting/making, opening for services

like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main

"T" runners to be suspended from ceiling using GI slotted cleats of

size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50

mm long dash fasteners, 4 mm GI adjustable rods with galvanised

butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm

center to center along main T, bottom exposed width of 24 mm of

all T-sections shall be pre-painted with polyester paint, all complete

for all heights as per specifications, drawings and as directed by

Engineer-in-charge.

GI Metal Ceiling Lay in perforated Tegular edge global

white color tiles of size 595x595 mm and 0.5 mm thick

with 8 mm drop; made of GI sheet having galvanizing of

100 gms/sqm (both sides inclusive) and 20% perforation

a) 12.52.2 area with 1.8 mm dia holes and having NRC (Noise sqm 299.54 2,068.75 619,680.72

Reduction Coefficient ) of 0.5, electro statically polyester

powder coated of thickness 60 microns (minimum),

including factory painted after bending and perforation,

and backed with a black Glass fiber acoustical fleece.

TOTAL (Carried Over to Summary of Civil Works) 1,134,893.14 -

J 13.0 FINISHING WORK

1 13.4 12 mm cement plaster of mix :

18 mm cement plaster in two coats under layer 12 mm thick cement

plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm

thick cement plaster 1:6 (1 cement : 6 fine sand).

Add or deduct for plaster drip course/ groove in or moulding to

R.C.C. projections.plastered surface

4 13.16 6 mm cement plaster of mix :

Extra for providing and mixing water proofing material in cement

plaster work in proportion recommended by the manufacturers.

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Distempering with 1st quality acrylic distemper (ready mixed) having

VOC content less than 50 gms/litre, of approved manufacturer, of

6 13.41.1 required shade and colour complete, as per manufacturer's Sqm 9912.08 185.65 1,840,178.09

specification. Two or more coats on new work.

Applying priming coats with primer of approved brand and

manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC

content less than 50 grams/litre

Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and

i 13.45.1 including priming coat of exterior primer applied @ 2.20kg/10 sqm Sqm 2455.31 223.60 549,008.10

Finishing walls with Deluxe Multi surface paint system for interiors

9 13.48 and exteriors using Primer as per manufacturers specifications :

Painting wood work with Deluxe Multi Surface Paint of required

shade. Two or more coat applied @0.90 ltr/10 sqm over an under

coat of primer applied @0.75 ltr/ 10 sqm of approved brand or

Providing and applying plaster of paris putty of 2 mm thickness over

10 13.26 plastered surface to prepare the surface even and smooth complete. Sqm 4608.71 262.70 1,210,709.42

Painting with synthetic enamel paint of approved brand and

manufacture to give an even shade :

i 13.61.1 Two or more coats on new work Sqm 385.97 155.90 60,172.41

Providing and applying white cement based putty of average

thickness 1 mm, of approved brand and manufacturer, over the

plastered wall surface to prepare the surface even and smooth

Providing and fixing GI hexagonal chicken wire mesh of size 12mm

x22g at the junction of disimilar surfaces of brick masonry wall and R

C C column by beams and the like including necessary nails for fixing

etc, complete all as per specification and direction of Engineer -in -

charge for all floor at all heights.

TOTAL (Carried Over to Summary of Civil Works) 11,797,442.42 45,423.30

K 21.0 ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators

and partitions with extruded built up standard tubular

sections/appropriate Z sections and other sections of approved

make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and

screws or with fixing clips, or with expansion hold fasteners including

necessary filling up of gaps at junctions, at top, bottom and sides

with required PVC/neoprene felt etc. Aluminium sections shall be

smooth, rust free, straight, mitred and jointed echanically wherever

required including cleat angle, Aluminium snap beading for glazing /

paneling, C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-charge.

Glazing and paneling to be paid for separately) :

a) 21.1.1 For fixed portion.

Powder coated aluminium (minimum thickness of powder coating 50

For shutters of doors, windows & ventilators including providing and

fixing hinges/ pivots and making provision for fixing of fittings

b) 21.1.2 wherever required including the cost of EPDM rubber / neoprene

gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50

Providing and fixing 12 mm thick prelaminated particle board flat

pressed three layer or graded wood particle board conforming to IS:

12823 Grade l Type ll, in panelling fixed in aluminum doors, windows

shutters and partition frames with C.P. brass / stainless steel screws

etc. complete as per architectural drawings and directions of

engineer-in-charge.

Pre-laminated particle board with decorative lamination on both

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions etc. with EPDM rubber / neoprene gasket

3 21.3 etc. complete as per the architectural drawings and the directions of

engineer-in-charge . (Cost of aluminium snap beading shall be paid

in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50

Filling the gap in between aluminium frame and adjacent

RCC/Brickwork/ Stone Work by providing weather silicon sealant

over backer rod of approved quality as per architectural drawings

and direction of Engineer-in-charge

i 21.8.1 Upto 5mm depth and 5mm width metre 878.70 96.75 85,014.23

Providing and fixing HPL sheet in required shape and size or as per

drawing including structural steel in frame work using M.S. square/

rectangular tube in the required pattern as per architectural

TOTAL (Carried Over to Summary of Civil Works) 590,111.42 1,467,123.65

L 22.0 WATER PROOFING

Supplying and Stacking Filling sunken floor with over burnt jhama

brick aggregate 120mm to 40mm including compacting of materials

complete as specified and directed for all levels.

Providing and laying water proofing treatment in sunken portion of

WCs, bathroom etc., by applying cement slurry mixed with water

proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water

proofing cement compound @ 0.253 kg/ sqm. This layer will be

allowed to air cure for 4 hours. (b) Second layer of slurry of cement

@ 0.242 kg/sqm mixed with water proofing cement compound @

0.126 kg/sqm. This layer will be allowed to air cure for 4 hours SQM 144.03 617.05 88,875.07

followed with water curing for 48 hours. The rate includes

preparation of surface, treatment and sealing of all joints, corners,

junctions of pipes and masonry with polymer mixed slurry.

Providing and laying integral cement based water proofing

treatment including preparation of surface as required for treatment

of roofs, balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of

cement admixed with water proofing compound conforming to IS.

i 2645 and approved by Engineer-in-charge over the RCC slab

including adjoining walls upto 300 mm height including cleaning the

surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25

mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5

coarse sand) admixed with water proofing compound conforming to

IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer

of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed

with water proofing compound conforming to IS : 2645 and

approved by Engineer-in-charge to required slope and treating

similarly the adjoining walls upto 300 mm height including rounding

of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement

slurry using 2.75 kg/ sqm of cement admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-

(d) Finishing the surface with 20 mm thick jointless cement mortar

of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-

charge including laying glass fibre cloth of approved quality in top

layer of plaster and finally finishing the surface with trowel with neat

cement slurry and making pattern of 300x300 mm square 3 mm

(e) The whole terrace so finished shall be flooded with water for a

minimum period of two weeks for curing and for final test.“All above

operations to be done in order and as directed and specified by the

Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra

TOTAL (Carried Over to Summary of Civil Works) 2,894,835.81

M 25.0 STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Providing and supplying aluminium extruded tubular and other

aluminium sections as per the architectural drawings and approved

shop drawings , the aluminium quality as per grade 6063 T5 or T6 as

per BS 1474, including super durable powder coating of 60-80

microns conforming to AAMA 2604 of required colour and shade as

1 25.1 approved by the Engineer-in-Charge. ( The item includes cost of Kg 1530.65 414.30 634,148.30

material such as cleats, sleeves, fasteners screws etc as desired.

necessary for fabrication of extruded aluminium frame work.

Nothing extra shall be paid on this account). The weight of

aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in

position semi (grid) unitized system of structural/ curtain wall glazing

2 25.2 (with open joints) for linear as well as curvilinear portions of the Sqm 695.75 3,510.50 2,442,430.38

building for all heights and all levels, including :

a) Structural analysis & design and preparation of shop drawings for

the specified design loads conforming to IS 875 part III (the system

must passed the proof test at 1.5 times design wind pressure

without any failure), including functional design of the aluminum

sections for fixing glazing panels of various thicknesses, aluminium

cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts,

bolts, clamps etc., structural and weather silicone sealants, flashings,

fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets

for water tightness, pressure equalization & drainage and protection

against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip galvanized /

Aluminium alloy of 6005 T5 brackets of required sizes, sections and

profiles etc. to accommodate 3 Dimensional movement for

achieving perfect verticality and fixing structural glazing system

rigidly to the RCC/ masonry/structural steel framework of building

structure using stainless steel anchor fasteners/ bolts, nylon

separator to prevent bimetallic contacts with nuts and washers etc.

of stainless steel grade 316, of the required capacity and in required

c) Providing and filling, two part pump filled, structural silicone

sealant and one part weather silicone sealant compatible with the

structural silicone sealant of required bite size in a clean and

controlled factory / work shop environment , including double sided

spacer tape, setting blocks and backer rod, all of approved grade,

brand and manufacture, as per the approved sealant design, within

and all around the perimeter for holding glass

d) Providing and fixing in position flashings of solid aluminium sheet

1 mm thick and of sizes, shapes and profiles, as required as per the

site conditions, to seal the gap between the building structure and

all its interfaces with curtain glazing to make it watertight.

e) Making provision for drainage of moisture/ water that enters the

curtain glazing system to make it watertight, by incorporating

principles of pressure equalization, providing suitable gutter profiles

at bottom (if required), making necessary holes of required sizes and

of required numbers etc. complete. This item includes cost of all

inputs of designing, labour for fabricating and installation of

aluminium grid, installation of glazed units, T&P, scaffolding and

other incidental charges including wastages etc., enabling temporary

structures and services, cranes or cradles etc. as described above

and as specified. The item includes the cost of getting all the

structural and functional design including shop drawings checked by

a structural designer, dully approved by Engineer-in-charge.

The item also includes the cost of all mock ups at site, cost of all

samples of the individual components for testing in an approved

laboratory, field tests on the assembled working structural glazing as

specified, cleaning and protection till the handing over of the

building for occupation. In the end, the Contractor shall provide a

water tight structural glazing having all the performance

characteristics etc. all complete as required, as per the Architectural

drawings, as per item description, as specified, as per the approved

shop drawings and as directed by the Engineer in-Charge.

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Note:- 1. The cost of providing extruded aluminium frames, shadow

boxes, extruded aluminium section capping for fixing in the grooves

of the curtain glazing and vermin proof stainless steel wire mesh

shall be paid for separately under relevant items under this subhead.

However, for the purpose of payment, only the actual area of

structural/ curtain wall glazing (including width of grooves ) on the

external face shall be measured in sqm. up to two decimal places.

Providing, assembling and supplying vision glass panels (IGUs)

comprising of hermetically-sealed 6-12- 6 mm insulated glass

(double glazed) vision panel units of size and shape as required and

specified, comprising of an outer heat strengthened (as approved)

glass 6mm thick, of approved colour and shade with reflective soft

coating on surface # 2 of approved colour and shade, an inner heat

strengthened (as approved) clear float glass 6mm thick, spacer tube

12mm wide, desiccants, including primary seal and secondary seal

(structural silicone sealant) etc. all complete for the required

performances, as per the Architectural drawings, as per the

approved shop drawings, as specified and as directed by the

Engineer-in-Charge. The IGUs shall be assembled in the factory/

workshop of the glass processor. (Payment for fixing of IGU Panels

in the curtain glazing is included in cost of item No.1.8.16 above).

For payment, only the actual area of glass on face # 1 of the glass

panels (excluding the areas of the grooves and weather silicone

sealant) provided and fixed in position, shall be measured in sqm.

(To be fixed on extruded aluminium sections. and cost of aluminium

sections to be paid in relevant item)

(i) Coloured tinted float glass 6mm thick Heat Strengthened

substrate with reflective soft coating on face # 2, + 12mm Airgap +

6mm Heat Strengthened clear Glass of approved make having

i i properties as visible Light transmittance (VLT) of 25 to 35 %, Light Sqm 695.75 3,718.70 2,587,285.53

reflection internal 10 to 15%, light reflection external 10 to 20 %,

shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2

Extra for openable side / top hung vision glass panels

(IGUs/laminated glass) including providing and supplying at site all

accessories and hardware for the openable panels as specified and

of the approved make such as heavy duty stainless steel friction

hinges, min 4 -point cremone locking sets with stainless steel plates,

handles, buffers etc. including necessary stainless steel screws/

fasteners, nuts, bolts, washers etc. all complete as per the

Architectural drawings, as per the approved shop drawings, as

specified and as directed by the Engineer in- Charge..

TOTAL (Carried Over to Summary of Civil Works) 5,791,586.50 -

N 26.0 NEW TECHNOLOGIES AND MATERIALS

Providing & fixing in position Phenol bonded Bamboowood flooring

with planks of sizes 14mm thick, minimum 1800mm length and

minimum 100 mm wide, in approved colour, texture and finish,

having Performance Appraisal Certificate (PAC) issued by Building

Materials & Technology Promotion Council (BMTPC). The flooring

shall be fixed with tongue and groove interlocking system, with

underlayment of 4mm thick expanded polyethylene foam sheets

having density 40kg/cum, over prepared surface with necessary

quarter round planks of size 1900mm x 18mm and door reducer of

size 1900mm x 44mm, wherever required. The bamboowood planks

shall have minimum density of 1000 Kg/cum & minimum Hardness

1000 Kgf. with Eco friendly UV coating, all complete as per direction

of the Engineer-in-charge.

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

SITC of Micro Perforated (Perfoaudile™) 16mm thick Wooden

Acoustic Wall Panels of size 600 x 2420mm, perforation diameter

will be 01-1.5 mm at a distance of 03 mm c/c as per acoustic

design/Architects approval, The micro perforated acoustic panels

top sheet will be of 0.5mm thick Mica laminate in desired shade as

per Engineer In charge / Architect’s approval and base made out of

16mm thick high density MDF board of 700-750 kg density with

10mm hole diameter perforation, micro perforated wooden acoustic

panels to be backed with black acoustic fleece. All joints of Micro

Perforated Acoustic Panels should have dowel connection to avoid

any sagging /unevenness. All Micro Perforated Acoustic Panels

should be fixed on GI ‘Z’ clamp made out of 0.7 mm thick GI sheet of

size 30 mm x 30 mm collar and 50 mm high to match with the

2 MR installed GI frame. The 50mm GI channel made out of GI sheet, 0.5 Sqm 633.47 12,282.00 7,780,327.67

mm thick. The GI Channel grid size will be – 600 x 900mm fixed to

wall using all screws of Stainless steel. Cavity of grid shall be filled

with Tissue fiber paper laminated Rockwool density 64 kg/m3

confirming to IS 8183 to achieve the best NRC value and finally

Micro Perforated Acoustic Panels fixed on GI Channel grid as final

finish. Micro Perforated Wall panel having 0.85 NRC value as per test

conducted by Prasar Bharti. The edges of the Micro Perforated

Acoustic Panel shall be Square edge at all four ends as per choice. All

makes and models of all items/samples should be approved by the

engineer-in-charge / consultant prior to the installation.

Technical Parameters Micro Perforated Acoustic Panels

Density - 700-750kg/m3

Fire Retardant – Class (A)

NRC Value – 0.85 with NRC System.

Providing and fixing mineral fibre false ceiling tiles at all heights of

size 595X595mm of approved texture, design and pattern. The tiles

should have Humidity Resistance (RH) of 99%, Light Reflectance >

85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire

Performance as per (BS 476 pt - 6 &7)in true horizontal level

suspended on interlocking T-Grid of hot dipped all round galvanized

iron section of 0.33 mm thick (galvanized @120 gsm) comprising of

main T runners of 15x32 mm of length 3000 mm, cross T of size

15x32mm of length 1200 mm and secondary intermediate cross T of

size 15x32 mm of length 600 mm to form grid module of size

600x600 mm suspended from ceiling using galvanized mild steel

item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6

dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000

mm length and L-shape level adjuster of size 85x25x2 mm, spaced at

1200 mm centre to centre along main ‘T’. The system should rest on

periphery walls /partitions with the help of GI perimeter wall angle

of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to

the wall with help of plastic rawl plug at 450 mm centre to centre &

40 mm long dry wall S.S. screws. The exposed bottom portion of all T-

sections used in false ceiling support system shall be pre-painted

with polyester baked paint, for all heights. The work shall be carried

out as per specifications, drawings and as per directions of the

engineer-incharge.

With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC

DSR-2023 DESCRIPTION UNIT QTY. DSR-2023 Amount NDSR RATE NDSR Amount

Aluminium Rafters

Providing & Fixing 2mm thick hollow alluminium louvers of size

1 NS 100mm x 150mm or 150mm x 200mm with all necessary accessories Sqm 229.93 8,500.00 1,954,362.50

Providing Design/Fabrication of SS Letter cut out on SS Grade 202

Steel.Corrosion Resistance/Hardened/ High Strength/Back lit High

Intensity LED Illuminated.Approved Design (TAMS BUILDING,

MAITHAN in English)Preparation of Letter and Fonts on

AUTOCAD.Plasma Cutting on Stainless Steel with Nitrogen to give

excellent surface finish for edge .Griding and Fabrication of

Letterswelding.Overall Size: 1200mmx20000mm

Providing and fixing of signages, modular curved frame

technology,of various widths and lengths, to form suggested

usages,made of aluminium extruded sections , duly anodised ,all

signages shall be provided with 0.6-0.8mm polycarbonate protecting

film over the prints, of appropriate size,

a ROOM NAME PLATE (80 mm x 300 mm) Each 18.00 1,650.00 29,700.00

BOTH SIDE- WALL PROJECTED LADIES TOILET (200 mm x 200 mm)

BOTH SIDE-WALL PROJECTED GENTS TOILET (200 mm x 200 mm)

d DOOR PLATE LADIES TOILET (80 mm x 300 mm) Each 1.00 1,860.00 1,860.00

e DOOR PLATE GENTS TOILET (80 mm x300 mm) Each 1.00 1,675.00 1,675.00

f ELECTRICAL PANEL (80 mm x 300 mm) Each 1.00 1,720.00 1,720.00

g DRINKING WATER (200 mm x 200 mm) Each 1.00 2,690.00 2,690.00

h AUTHORISED PERSONAL ONLY (80 mm x 300 mm) Each 3.00 1,700.00 5,100.00

Providing and fixing of signages,customised to the architect's

design,the signage to be made of 10 mm casted clear acrylic sheet

duly cut by laser, all text to be of 2 mm thick acrylic duly laser cut,

partially housed and pasted on to engraved surface of the text in the

4 NS clear acrylic base, the 10mm acrylic sheet to be fixed on 25x25mm

section of teak wood with help of crafted SS pins, and further fixed

to the priscribed location with the help of wooden dowels,and

required adhesive,as per drawing.

b FLOOR LEVEL (600 mm x 300 mm) Each 2.00 9,198.00 18,396.00

c CONFERENCE ROOM (400 mm x 400 mm) Each 1.00 8,176.00 8,176.00

TOTAL (Carried Over to Summary of Civil Works) 11,431,974.53 10,666,255.17

ALL SUB-HEAD TOTAL 123,044,238.33 14,142,723.37

GRAND TOTAL 137,186,961.70

GRAND TOTAL 137,186,961.70

PROPOSED CONSTRUCTION OF TWO STOREYED TAMS BUILDING AT DVC MAITHON

ABSTRACT OF ELECTRICAL WORKS ESTIMATE

SL. NO. DESCRIPTION

1 SUBHEAD :1_WIRING 2,820,367 0

2 SUBHEAD :2_LIGHT FITTINGS AND FANS 1,574,928 121,034

3 SUBHEAD :3_MCB ,DB'S 167,509 0

4 SUBHEAD :4_LT CABLE, LAYING & TERMINATIONS 184,149 1,680,147

5 SUBHEAD :5_CABLE TRAY 125,071 0

6 SUBHEAD :6_11KV COMPACT SUB-STATION 0 9,717,615

7 SUBHEAD :7_HT CABLE, LAYING & TERMINATIONS 171,694 479,597

8 SUBHEAD :8_ELE. MEDIUM VOLTAGE PANELS 320,033 5,235,851

9 SUBHEAD :9_UPS 208,893 0

10 SUBHEAD :10_EARTHING 338,314 0

11 SUBHEAD :11_LIGHTNING PROTECTION SYSTEM 0 855,611

12 SUBHEAD :12_SOLAR PV POWER GENERATION 3,799,600 0

13 SUBHEAD :13_FIRE ALARM SYSTEM 2,233,768 27,209

14 SUBHEAD :14_PUBLIC ADDRESS SYSTEM 972,152 0

15 SUBHEAD :15_DATA & VOICE SYSTEM 5,994,320 0

16 SUBHEAD :16_CCTV SYSTEM 2,310,549 181,827

17 SUBHEAD :17_ACCESS CONTROL SYSTEM 256,451 49,452

18 SUBHEAD :18_SECURITY SYSTEM 0 392,491

19 SUBHEAD :19_DIESEL GENERATOR SET 2,433,003 0

20 SUBHEAD :20_LIFT 3,368,451 0

21 SUBHEAD :21_EXTERNAL LIGHTING 232,158 1,858,313

22 SUBHEAD :22_MISCELLANEOUS ITEMS 110,895 0

GRAND TOTAL 48,221,453

GRAND TOTAL 48,221,453

Digitally signed by SUPARNA

PROPOSED CONSTRUCTION OF TWO STOREYED TAMS BUILDING AT DVC MAITHON SUBSTATION

ESTIMATE-ELECTRICAL WORKS

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

SUBHEAD :1_WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm

FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed

1 1.10 medium class PVC conduit, with modular switch, modular plate, suitable GI box and

earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single

core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point

( without independent switch etc.) with 1.5 sq. mm FRLS/HFFR PVC insulated copper

3 1.55 conductor single core cable in surface/ recessed PVC conduit, and earthing the point with

1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as

Wiring for circuit/ submain wiring along with earth wire with the following sizes of

5 1.7 FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed steel

conduit as required.

6 1.7.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire (For UPS) Meter 10 1253 12530

Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor,

7 1.17 single core cable in the existing surface/ recessed steel/ PVC conduit as required.

8 1.17.3 3 X 1.5 sq. mm (For circuit wiring) Meter 600 104 62400

9 1.17.12 3 X 2.5 sq. mm (For circuit wiring) Meter 1500 148 222000

10 1.17.21 3 X 4.0 sq. mm (For power point wiring) Meter 2050 222 455100

Supplying and fixing of following sizes of medium class PVC conduit along with

11 1.21 accessories in surface/recess including cutting the wall and making good the same in case

of recessed conduit as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box

excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface

14 1.31 or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A Each 50 545 27250

modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface

15 1.32 or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet Each 49 659 32291

and 15/16 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface

or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2

nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in

non residential buildings).

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface

17 1.57 or in recess including providing and fixing 25 A modular socket outlet and 25 A modular Each 4 807 3228

SP MCB, "C" curve including connections, painting etc. as required.

Supplying & fixing of 20 A, 240 V, SPN Insustrial type socket outlet, with 2 pole and

earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel

enclosure, on surface or in recess, with chained metal cover for the socket outlet and

complete with connections, testing and comissioning etc.as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing

19 1.25 modular plate switch box including connections but excluding modular plate etc. as Each 114 402 45828

20 TOTAL OF SUBHEAD :1 2820367 0

21 SUBHEAD :2_LIGHT FITTINGS AND FANS

Brush Less Direct Current (BLDC) Fan without Remote

Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct

Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30

cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body

Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM

(tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%,

22 9.2 suitable for operation with regulator for speed control and all remaining accessories

including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation

resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply,

Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm

FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as

23 9.2.3 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) Each 114 2695 307230

Installation of exhaust fan in the existing opening, including making good the damage,

connection, testing, commissioning etc. as required

26 1.51 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes Each 20 260 5200

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

LED Down lighter (SMD Type) (System lumen efficacy >135lm/Watt)

Supplying, Installation, Testing & Commissioning of LED Recessed/surface Down lighter

(Round /square/Rectangular) SMD type of following body material with PMMA and

prismatic diffuser and construction as per IS : 10322 with driver as per the requirement

with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz,

Operating temp range - 5 0C to 40 0C, internal surge protection of 2.5 KV with Short &

Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare

Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED, Driver &

electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial

Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT

3000°K/ 4000°K /5700°K / 6500°K (As per ANSI Bin), SDCM(Standard Deviation

27 8.3 Color Matching) <3, Maximum power consumption should not more than the specified

rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name

Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external

connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core

cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen

efficacy >135 lm/Watt output. LM79 & LM80 Test report and all testing required for

LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by

Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium

housing such that LED junction temperature shall not rise above 90°C).

28 Powder coated die cast /Extruded aluminum Body including trim .

LED Batten light (System lumen efficacy ≥120 <135 lm/Watt)

Supplying, installation, Testing & Commissioning of LED surface mounted Batten light

of following body material and construction as per IS : 10322 with driver (Replaceable) as

per the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt,

frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5

KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80,

Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical

circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till

ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard

33 8.10 Deviation Colour Matching) <3, Maximum power consumption

should not more than the specified rating and Fixture shall be of relevant BIS standard.

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.

complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC

insulated copper conductor single core cable and earthing etc. as required with Minimum

5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 &

LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.

Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement.

(Thermal management: heat sink of aluminium housing such that LED junction

temperature shall not rise above 90°C).

Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)

LED Flood Light, powder coated pressure die cast aluminum (System lumen

efficacy >135 lm/Watt)

Supplying, Installation, Testing & Commissioning of Flood Light, powder coated pressure

die cast aluminium body with built in or separate driver as per the requirement with

Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60

hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per

IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95,

IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC as per

CISPR-15, lenses for beam angle 30 deg-120deg as per the application and the project

requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of

36 8.17 minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per

LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As

per ANSI Bin) , SDCM(Standard Deviation Colour Matching) <5, Maximum power

consumption should not more than the specified rating and Fixture shall be of relevant

BIS standard complete in all respect i/c external connections with 1.5 sq.mm

FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt

output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS

shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as

per requirement. (Thermal management: heat sink of aluminium housing such that LED

junction temperature shall not rise above 90°C).

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of following body

material and construction as per IS : 10322 with driver as per the requirement with Driver

efficiency >85%, Operating voltage AC 140- 270 Volt, freq 50/60 hz, Operating temp

range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short &

Open circuit protection,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare

Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver &

electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen

maintained till life ends ,CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI

Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption

38 8.8 should not more than the specified rating and Fixture shall be of relevant BIS standard

and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5

sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt

output . LM79 & LM80 Test report from NABL lab for all testing required for LED

fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by

Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum

housing such that LED junction temperature shall not rise above 90°C).

Powder coated die cast / Extruded aluminium Body (Thickness≥ 1.20 mm)

Supply and installation of Energy saving new generation 10W LED 6500K bulkhead

40 MR luminaire with opal diffuser etc with all fixing accessories as required of Hevells Cate. Each 6 1425 8552

Ref RUGBYGENXFTS10WLED865SSYMBOPC or apporoved equivalent.

Supply and installation of Flexiible LED strips with optimum brightness & uniformity of

41 MR light for perfect cove lighting, with all fixing accessories as required of Cate. Ref. Each 12 1145 13734

FLEXISTRIP5MIP2024V/2ALED865MOD V1or apporoved equivalent.

Supply and installation of Driver for Flexiible LED strips with all fixing accessories as

42 MR required of Cate. Ref. Constant Voltage Driver24V2Aupto 48W V1 or apporoved Each 12 1209 14512

Supply and installation of 450 mm, 230 V A.C. wall mounted Air circulator, heavy duty

43 MR fan including fixing the bracket, making connection, testing, commissioning etc as Each 1 7226 7226

required.of Cate. Ref. HAVELLS : FHWV3TFSLB18 or apporoved equivalent.

Supply of sizes 200 mm, 230 v A.C.Plastic body exhaust fan complete with

44 MR motor,blades,frame, bracket, lover/shutter etc. as required of Cate. Ref. HAVELLS : Each 8 2435 19478

FHVDXHSWHT08 or apporoved equivalent.

Supply of sizes 230 mm, 230 v A.C. heavay duty exhaust fan complete with

45 MR motor,blades,frame, bracket, lover/shutter etc. as required of Cate. Ref. HAVELLS : Each 7 2691 18835

FHVVEMTDBB09 or apporoved equivalent.

Supply of sizes 450 mm, 230 v A.C. heavay duty exhaust fan complete with

46 MR motor,blades,frame, bracket, lover/shutter etc. as required of Cate. Ref. HAVELLS : Each 5 7740 38698

FHEHDSPGRY18 or apporoved equivalent.

47 TOTAL OF SUBHEAD :2 1574928 121034

48 SUBHEAD :3_MCB ,DB'S

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel,

MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing

etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB

distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/RCCB/Isolator

53 2.3.1 6 way, Double door Each 1 2390 2390

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit

54 2.10 breaker suitable for inductive load of following poles in the existing MCB DB complete

with connections, testing and commissioning etc. as required

55 2.10.1 Single pole Each 200 285 57000

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required

Supplying and fixing following rating, double pole, 230 V, isolator in the existing MCB

DB complete with connections, testing and commissioning etc. as required

Supplying and fixing following rating,four pole, (three phase and neutral), 415 volts,

residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the

existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole

62 2.24 and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete

with testing and commissioning etc.as required.

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

63 2.24.2 For 6 way, Double door TPN MCBDB Each 3 1223 3669

64 2.24.3 For 8 way, Double door TPN MCBDB Each 6 1448 8688

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole

65 2.23 and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete

with testing and commissioning etc.as required.

66 2.23.1 For 6 way, Double door SPN MCBDB Each 1 834 834

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

68 TOTAL OF SUBHEAD :3 167509 0

69 SUBHEAD :4_LT CABLE, LAYING & TERMINATIONS

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV

grade of following size in the existing RCC/ HUME/ metal pipe as required.

73 10.5.3 Above 95 sq. mm and upto 185 sq. mm Meter 367 97 35599

74 10.5.4 Above 185 sq. mm and upto 400 sq. mm Meter 305 170 51765

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable

of 1.1 KV grade of following size on cable tray as required.

76 10.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Meter 391 53 20736

77 10.8.2 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) Meter 58 109 6295

78 10.8.3 Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) Meter 32 138 4416

79 CABLE TERMINATION

Supplying and making end termination with brass compression gland and aluminium lugs

80 11.1 for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor

cable of 1.1 KV grade as required.

86 SUPPLY OF CABLE

Supply of XLPE insulated and PVC sheathed power cable of 1.1 kV grade, 1.1 kV, multi

core, aluminum,armored , underground, Conforming to IS 7098-2

91 MR 4c x 25 sqmm Meter 26 366 9599

93 MR 4c x 6 sqmm Meter 95 190 17958

Supply and termination of XLPE insulated & PVC sheathed Armoured copper cables of

94 1.1 KV grade with copper conductor as per IS 7098 Part-I -1988 including all labour

charges, giving connections etc., complete as required.

95 MR 2 Core, 6 Sq.mm (For Submain) Meter 120 340 40771

96 MR 3 Core, 6 Sq.mm (For Submain) Meter 10 466 4659

97 MR 4 Core, 6 Sq.mm (For Submain) Meter 30 609 18278

98 MR 4 Core, 10 Sq.mm (For Submain) Meter 90 967 87070

99 TOTAL OF SUBHEAD :4 184149 1680147

100 SUBHEAD :5_CABLE TRAY

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable

tray (Galvanisation thickness not less than 50 microns) with perforation not more than

17.5%, in convenient sections, joined with connectors, suspended from the ceiling with

G.I. suspenders including G.I. bolts & nuts, etc. as required.

102 4.6.2 150 mm width X 50 mm depth X 1.6 mm thickness Meter 50 803 40150

103 4.6.7 600 mm width X 50 mm depth X 2.0 mm thickness Meter 35 1925 67375

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable

tray "bends" (galvanisation not less than 50 microns) with perforation not more than

17.5%, in convenient sections, joined with connectors, suspended from the ceiling with

G.I. suspenders including G.I. bolts & nuts, etc. as required.

105 4.7.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 7 1368 9576

106 4.7.7 600 mm width X 50 mm depth X 2.0 mm thickness Each 2 3985 7970

107 TOTAL OF SUBHEAD :5 125071 0

108 SUBHEAD :6_11KV COMPACT SUB-STATION

Design, Supply, Erection, Testing and Commissioning of 11/0.433 KV, Smart Compact

Substation (CSS) on existing foundation along with 11kV 4 Way (3LBS+1VCB) RMU,

Distribution Transformer and LT Switchgears complete set, type tested in line with latest

IEC standards of IEC 62271-202 only.

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Outdoor type enclosure having modular construction of 2 mm Galvanised Sheet Steel.

The Enclosure shall have IP54 degree of protection for MV & LT switchgear

compartment & IP34 degree of protection for Transformer compartment. Each

compartment will be provided with the door and pad locking arrangement. The

110 Compartment illumination lamp with door operated switch shall be provided for each

compartment. Interconnection Between MV switchgear & Transformer using XLPE

single core cable & Interconnection between Transformer & LT switchgear using

Busbars. Internal earthing connections. All metallic components shall be earthed to a

common earthing point.

PSS Enclosure should be Internal Arc Tested for IAC A & B both conditions for 21 kA

111 for 1 sec, as per IEC 62271-202.

PSS Enclosure shall be K10 class.

11/0.415kV, 500kVA Compact Substation :11/0.415kV Outdoor type Compact Sub-

Station, equipped with 500KVA 11KV/433V, DYn11 Oil filled hermatically sealed

transformer, 4 Way 11kV Ring Main Unit consisting of 3 nos. 630A at 11kV load

112 breaking switch with 1 nos. tee-off as SF6 insulated 200A Vacuum Circuit Breaker &

800A 415V 50KA 4P Fixed Manual Air Circuit Breaker with numerical overcurrent and

earthfault protection as secondary side control as detailed below. The detail bill of

material for each Compact Substation shall be as under:

PSS shall have bucket type lifting arrangement connected from base of PSS for all PSS

114 HT Switchgear

4way Non - Extensible unit RMU with 3no. 630 A load break switch and 1 no. 200A

Tee off with VCB self powered with O/C + E.F. Relay, with Motorized LBS & VCB.

116 Each Load Break Switch (LBS) consists of :

Manually operated 630A load breaker switch with built-in earth switch having full

making capacity.

118 Mechanical position indicator. Switch ON/OFF/EARTHED.

119 Live Cable Indication.

120 Cable compartment cover interlocked with earth switch.

Cable termination bushings suitable for 3 no. 1CX300mm2 XLPE cable and must be site

replacable type.

122 Cable termination cover boots (Push on type)

123 Each VCB Feeder consists of following:

Motorized 200A VCB spring charging arrangement and manual close & open push

buttons, ON / OFF indication.

Self powered O/C & E/F relay type CSDPR with single core cast resin type

CT.(Protection Core - 1.2VA & CL-5P10)

126 Motorized 200A load breaker switch with built in earth switch.

127 Mechanical position indicator. Switch ON/OFF/EARTHED.

128 Live Cable Indication and VCB operating sequence must be O-0.3Sec-CO-3MIN-CO

129 Cable compartment cover interlocked with earth switch.

Cable termination bushings suitable for 3 no. 1CX300mm2 XLPE cable and must be site

replacable type.

131 Cable termination cover boots (Push on type)

132 VCB shall have line side ES having own making capacity independent of breaker.

133 VCB shall have 50 nos. short circuit breaking operations at 21 kA.

134 BUS PT For Metering

Air Insulated enclosure with necessary bus connection via bushing. VT’s from the

135 manufacturer and according to IS 3156 shall be accepted.

11KV/rt3/110V/rt3; 25VA class 0.5. Single phase bus PT for metering - 3 Nos.

136 TRANSFORMER-

500KVA capacity (continuous loading) BEE 5 Star rated (Corresponding Level as per

BIS amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase, 50 Hz,

Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound transformer

(Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain

Oriented (CRGO) Core grade MOH or better, suitable for out door/indoor applications

with On Load Tap Changer OLTC and facility for remote and manual operation of OLTC

HV side in range of +5% to -15% in steps of 2.5%, having cable end boxes on HV side

suitable for 3x300 sqmm XLPE cable of 11 KV grade, including bus trunking

arrangement on LV side including supplying and laying of copper conductor multicore

control cable from transformer to HT breaker/panel for safety tripping, complete with all

accessories and safety provisions as per relevant IS Code including first filling of filtered

dehydrated oil, i/c supplying and grouting of suitable M.S. Channel with all accessories

and transformer shall be confirming to IS : 2026 (Part 1 to Part 5), IS : 1180 and duly ISI

Marked and as per CPWD specifications complete in all respects etc as required at site.

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Design ambient condition :

a) air temperature 50 deg C,

b) Relative Humidity 90 % Max,

c) Seismic Zone as per location of site,

d) Altitude as per location/site.

Noise level Shall not exceed limits as per NEMA TR-1 with all accessories running

measured as per IEC 551 / NEMA standard.The transformer should have QR code which

should contain drawing, test report OEM manual,Geo- Tag of manufacturing location etc.

139 Marking Each transformer shall be provided with rating plate made of anodized

aluminum/ stainless steel material securely fixed on the outer body, easily accessible, as

per IS: 1180. The entries on the rating plate shall be indelibly marked.

The maximum flux density in any part of the core and yoke at rated voltage and frequency

shall be such that the flux density with + 12.5 percent combined voltage and frequency

variation from rated voltage and frequency does not exceed 1.9 Tesla. The permissible

temperature-rise shall not exceed 35 dg.C for oil and 40 dg. C up to 200 KVA and 40

dg.C for oil and 45 dg. C for above 200 KVA for winding. Inside of tank shall be painted

140 with varnish or liquid resistant paint. For external surfaces one coat of thermo setting

powder paint or one coat of epoxy primer followed by two coats of polyurethane base

paint shallbe used. IS: 1180 shall be referred to for paint thickness for normal to medium

corrosive atmosphere. For highly polluted atmosphere and special application external

paint work shall be as per direction of Engineer-in-Charge.

141 Fitting and Accessories : The following fittings shall be provided:-

142 a) Two earthing terminals with the earthing symbol

b) Oil level gauge indicating oil level at minimum, 30°C and maximum operating

144 c) Air release device (for non-sealed type transformers)

145 d) Rating and terminal marking plates;

146 e) Silica gel breather

f) Drain-cum-sampling valve (¾″ nominal size thread, IS 554) preferably steel with plug

for three phase transformers;

148 g) Thermometer pocket with cap;

h) Oil filling holes having (1¼″ nominal size thread) with cover (for sealed type

transformers without conservator);

150 i) Lifting lugs for the complete transformer as well as for core and winding assembly;

151 j) Pressure relief device or explosion vent;

152 k) One filter valve on the upper side of the tank;

153 l) Unidirectional flat rollers;

154 m) Inspection hole;

n) HV side neutral grounding strip (where one of the HV bushing terminal is connected to

156 o) Arcing horns or suitable rating lightning arrestors for HT side – 3 Nos.

157 p) Bird guard;

q) Oil temperature indicator and winding temperature indicators for transformers with

suitable tripping mechanism above permissible limit

159 r) Additional Neutral separately brought out on bushing for earthing.

160 s) Non return valve (for conducting pressure test);

161 t) Pressure relief device or explosion vent

162 u). Monogram Plate

163 v) Inspection cover

164 w). Detachable type radiators with top and bottom shutoff valve.

165 x) Oil Conservator with Oil level indicator, minimum level marking and drain plug.

y) Necessary hardware, clamps, lugs etc. for termination on HV/MV etc. for all

Transformer manufacturer shall have In-House Dust free Core cutting Vapor Phased

Drying NABL accredited test facility.

168 LT Switchgear

800Amps 415V 50KA 4P Fixed Manual Air Circuit Breaker with numerical overcurrent

and earth fault protection.

11KV OUTDOOR UNITISED SUB-STATION above & as per SLD

PSS enclosure, RMU, Vacum Interrupter, ACB shall be of same make and License

170 MR partner, Authorized system house make PSS are not accepted. PSS Enclosure must Each 1 5398675 5398675

be type tested for 21KA/1sec with IAC-A&B classification.

Approved PSS Manufacturer - Schneider/ABB/Siemens

Design, Supply, Erection, Testing and Commissioning of 11/0.433 KV, Smart Compact

Substation (CSS) on existing foundation along with 11kV 2 Way (1LBS+1VCB) RMU,

Distribution Transformer and LT Switchgears complete set, type tested in line with latest

IEC standards of IEC 62271-202 only.

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Outdoor type enclosure having modular construction of 2 mm Galvanised Sheet Steel.

The Enclosure shall have IP54 degree of protection for MV & LT switchgear

compartment & IP34 degree of protection for Transformer compartment. Each

compartment will be provided with the door and pad locking arrangement. The

172 Compartment illumination lamp with door operated switch shall be provided for each

compartment. Interconnection Between MV switchgear & Transformer using XLPE

single core cable & Interconnection between Transformer & LT switchgear using

Busbars. Internal earthing connections. All metallic components shall be earthed to a

common earthing point.

PSS Enclosure should be Internal Arc Tested for IAC A & B both conditions for 21 kA

173 for 1 sec, as per IEC 62271-202.

PSS Enclosure shall be K10 class.

11/0.415kV, 500kVA Compact Substation :11/0.415kV Outdoor type Compact Sub-

Station, equipped with 500KVA 11KV/433V, DYn11 Oil filled hermatically sealed

transformer, 2 Way 11kV Ring Main Unit consisting of 1 nos. 630A at 11kV load

174 breaking switch with 1 nos. tee-off as SF6 insulated 200A Vacuum Circuit Breaker &

800A 415V 50KA 4P Fixed Manual Air Circuit Breaker with numerical overcurrent and

earthfault protection as secondary side control as detailed below. The detail bill of

material for each Compact Substation shall be as under:

PSS shall have bucket type lifting arrangement connected from base of PSS for all PSS

176 HT Switchgear

2way Non - Extensible unit RMU with 1no. 630 A load break switch and 1 no. 200A

Tee off with VCB self powered with O/C + E.F. Relay, with Motorized LBS & VCB.

178 Each Load Break Switch (LBS) consists of :

Manually operated 630A load breaker switch with built-in earth switch having full

making capacity.

180 Mechanical position indicator. Switch ON/OFF/EARTHED.

181 Live Cable Indication.

182 Cable compartment cover interlocked with earth switch.

Cable termination bushings suitable for 3 no. 1CX300mm2 XLPE cable and must be site

replacable type.

184 Cable termination cover boots (Push on type)

185 Each VCB Feeder consists of following:

Motorized 200A VCB spring charging arrangement and manual close & open push

buttons, ON / OFF indication.

Self powered O/C & E/F relay type CSDPR with single core cast resin type

CT.(Protection Core - 1.2VA & CL-5P10)

188 Motorized 200A load breaker switch with built in earth switch.

189 Mechanical position indicator. Switch ON/OFF/EARTHED.

190 Live Cable Indication and VCB operating sequence must be O-0.3Sec-CO-3MIN-CO

191 Cable compartment cover interlocked with earth switch.

Cable termination bushings suitable for 3 no. 1CX300mm2 XLPE cable and must be site

replacable type.

193 Cable termination cover boots (Push on type)

194 VCB shall have line side ES having own making capacity independent of breaker.

195 VCB shall have 50 nos. short circuit breaking operations at 21 kA.

196 TRANSFORMER-

500KVA capacity (continuous loading) BEE 5 Star rated (Corresponding Level as per

BIS amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase, 50 Hz,

Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound transformer

(Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain

Oriented (CRGO) Core grade MOH or better, suitable for out door/indoor applications

with On Load Tap Changer OLTC and facility for remote and manual operation of OLTC

HV side in range of +5% to -15% in steps of 2.5%, having cable end boxes on HV side

suitable for 3x300 sqmm XLPE cable of 11 KV grade, including bus trunking

arrangement on LV side including supplying and laying of copper conductor multicore

control cable from transformer to HT breaker/panel for safety tripping, complete with all

accessories and safety provisions as per relevant IS Code including first filling of filtered

dehydrated oil, i/c supplying and grouting of suitable M.S. Channel with all accessories

and transformer shall be confirming to IS : 2026 (Part 1 to Part 5), IS : 1180 and duly ISI

Marked and as per CPWD specifications complete in all respects etc as required at site.

Design ambient condition :

a) air temperature 50 deg C,

b) Relative Humidity 90 % Max,

c) Seismic Zone as per location of site,

d) Altitude as per location/site.

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Noise level Shall not exceed limits as per NEMA TR-1 with all accessories running

measured as per IEC 551 / NEMA standard.The transformer should have QR code which

should contain drawing, test report OEM manual,Geo- Tag of manufacturing location etc.

199 Marking Each transformer shall be provided with rating plate made of anodized

aluminum/ stainless steel material securely fixed on the outer body, easily accessible, as

per IS: 1180. The entries on the rating plate shall be indelibly marked.

The maximum flux density in any part of the core and yoke at rated voltage and frequency

shall be such that the flux density with + 12.5 percent combined voltage and frequency

variation from rated voltage and frequency does not exceed 1.9 Tesla. The permissible

temperature-rise shall not exceed 35 dg.C for oil and 40 dg. C up to 200 KVA and 40

dg.C for oil and 45 dg. C for above 200 KVA for winding. Inside of tank shall be painted

200 with varnish or liquid resistant paint. For external surfaces one coat of thermo setting

powder paint or one coat of epoxy primer followed by two coats of polyurethane base

paint shallbe used. IS: 1180 shall be referred to for paint thickness for normal to medium

corrosive atmosphere. For highly polluted atmosphere and special application external

paint work shall be as per direction of Engineer-in-Charge.

201 Fitting and Accessories : The following fittings shall be provided:-

202 a) Two earthing terminals with the earthing symbol

b) Oil level gauge indicating oil level at minimum, 30°C and maximum operating

204 c) Air release device (for non-sealed type transformers)

205 d) Rating and terminal marking plates;

206 e) Silica gel breather

f) Drain-cum-sampling valve (¾″ nominal size thread, IS 554) preferably steel with plug

for three phase transformers;

208 g) Thermometer pocket with cap;

h) Oil filling holes having (1¼″ nominal size thread) with cover (for sealed type

transformers without conservator);

210 i) Lifting lugs for the complete transformer as well as for core and winding assembly;

211 j) Pressure relief device or explosion vent;

212 k) One filter valve on the upper side of the tank;

213 l) Unidirectional flat rollers;

214 m) Inspection hole;

n) HV side neutral grounding strip (where one of the HV bushing terminal is connected to

216 o) Arcing horns or suitable rating lightning arrestors for HT side – 3 Nos.

217 p) Bird guard;

q) Oil temperature indicator and winding temperature indicators for transformers with

suitable tripping mechanism above permissible limit

219 r) Additional Neutral separately brought out on bushing for earthing.

220 s) Non return valve (for conducting pressure test);

221 t) Pressure relief device or explosion vent

222 u). Monogram Plate

223 v) Inspection cover

224 w). Detachable type radiators with top and bottom shutoff valve.

225 x) Oil Conservator with Oil level indicator, minimum level marking and drain plug.

y) Necessary hardware, clamps, lugs etc. for termination on HV/MV etc. for all

Transformer manufacturer shall have In-House Dust free Core cutting Vapor Phased

Drying NABL accredited test facility.

228 LT Switchgear

800Amps 415V 50KA 4P Fixed Manual Air Circuit Breaker with numerical overcurrent

and earth fault protection.

11KV OUTDOOR UNITISED SUB-STATION above & as per SLD

PSS enclosure, RMU, Vacum Interrupter, ACB shall be of same make and License

230 MR partner, Authorized system house make PSS are not accepted. PSS Enclosure must Each 1 4318940 4318940

be type tested for 21KA/1sec with IAC-A&B classification.

Approved PSS Manufacturer - Schneider/ABB/Siemens

231 TOTAL OF SUBHEAD :6 0 9717615

232 SUBHEAD :7_HT CABLE, LAYING & TERMINATIONS

233 Supply of Cable

Supplying of the following sizes of 11 KV Alum. (E), Armoured XLPE HT power cable

as per IS7098(part-2)-1985 amended uptodate, as per specifications.

235 MR 11 KV (E), 3C x 300 Sq. mm XLPE Aluminium cable Armoured Meter 110 4360 479597

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV

grade of following size in the existing RCC/ HUME/ METAL pipe as required.

238 22.3.2 Above 120 sq. mm and upto 400 sq. mm Meter 110 170 18700

239 End Termination

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Supplying and making indoor cable end termination with heat shrinkable jointing kit

240 23.4 complete with all accessories including lugs suitable for following size of 3 core, XLPE

aluminium conductor cable of 11 KV grade as required:

Supplying and making outdoor cable end termination with heat shrinkable jointing kit

242 23.5 complete with all accessories including lugs suitable for following size of 3 core, XLPE

aluminium conductor cable of 11 KV grade as required:

244 TOTAL OF SUBHEAD :7 171694 479597

245 SUBHEAD :8_ELE. MEDIUM VOLTAGE PANELS

NOTE: Contactor will submit the GA Drawings of Panel for Approvel from

Clint/Consultant before order the panel.

247 MAIN LT PANEL

Design, Fabrication, Shifting, Supply, Erection,Testing and commisioning of 415V, 3

Phase, 50 Hz., 4 wire system, sheet steel clad, dust and vermin proof cubical and Indoor

type floor mounted, free standing extendible type Main LT Panel compartmentalized

design and fabricated out of 2 mm CRCA sheet steel complete with Aluminium Bus bars,

Electrical interlocks as per the various status of all the equipments indicated on the

drawings. Providing & Fixing of base plate / channel, P/F the following Switchgears,

complete with earth Bus bar throughout the length of the panel, terminal arrangement for

Cables/ busducts, incomings / Outgoings from Top / Bottom as per drawings and as

approved by consultant / Engineer incharge, The incoming and outgoing feeders shall be

accommodated in a modular multi-tier arrangement, detachable gland plates, adequate

size cable alley, Sign writing, Painting, Earthing, Numbering, Danger plate, including

PVC insulated copper FRLS wires of minimum 1.5sq.mm & 2.5sq.mm for CT's etc.

complete as required as per specifications and drawing attached.

249 INCOMER FROM PSS-01 (500KVA)

1 Nos. 800Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.

251 1 Nos. 800Amps, 415V FP CONTACTOR (AC-1 DUTY).

Digital Multifunction energy meter with RS485 showing V, A, PF, KVAR, KWH etc.

current transformers of 800/5A ratio, 10 VA Class 1.0 metering.

253 One (1) Set of Phase Indication & ON/OFF/TRIP Lamp with 2A SP MCB.

254 Control MCB'S, control terminals & wiring as required.

Under/ Over voltage, Master trip relays along with current transformers of 800/5A ratio,

10 VA class-5P10 protection - 1 set

256 Suitable arrangement to receive incoming armored cables.

257 Ameter with ASS

258 Voltmeter with VSS

259 ON/OFF/TRIP Indication

260 Open/Close Push button

261 Auto/Manual selector switch

262 APFC relay

263 INCOMER FROM PSS-02 (500KVA)

1 Nos. 800Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.

265 1 Nos. 800Amps, 415V FP CONTACTOR (AC-1 DUTY).

Digital Multifunction energy meter with RS485 showing V, A, PF, KVAR, KWH etc.

current transformers of 800/5A ratio, 10 VA Class 1.0 metering.

267 One (1) Set of Phase Indication & ON/OFF/TRIP Lamp with 2A SP MCB.

268 Control MCB'S, control terminals & wiring as required.

Under/ Over voltage, Master trip relays along with current transformers of 800/5A ratio,

10 VA class-5P10 protection - 1 set

270 Suitable arrangement to receive incoming armored cables.

271 Ameter with ASS

272 Voltmeter with VSS

273 ON/OFF/TRIP Indication

274 Open/Close Push button

275 Auto/Manual selector switch

276 APFC relay

277 BUS COUPLER

1 Nos. 800Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.

279 1 Nos. 800Amps, 415V FP CONTACTOR (AC-1 DUTY).

280 ON/OFF Indication

281 Open/Close Push button

282 Auto/Manual selector switch

283 INCOMER FROM 125 KVA DG PANEL

284 Incomer from DG Set shall be provided with the following:

1 Nos. 200Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.

286 1 Nos. 200Amps, 415V FP CONTACTOR (AC-1 DUTY).

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Digital Multifunction energy meter with RS485 showing V, A, PF, KVAR, KWH etc.

current transformers of 200/5A ratio, 10 VA Class 1.0 metering.

288 Control MCB'S, control terminals & wiring as required.

Under/ Over voltage, Master trip relays along with current transformers of 200/5A ratio,

10 VA class-5P10 protection - 1 set

290 Suitable arrangement to receive incoming armored cables.

291 Ameter with ASS

292 Voltmeter with VSS

293 ON/OFF/TRIP Indication

294 Open/Close Push button

295 Auto/Manual selector switch

296 Reverse power Protection Relay.

297 INTERLOCKING.

298 DG Incomer, and AMF logic, interlocking with main incomers & Bus-Couplers.

1000 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable

busbar insulation) supported by DMC / FRP insulators.

2 Nos. 630Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.(MDB-HVAC)

2 Nos. 320Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.(APFC PANEL)

2 Nos. 250Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.(FIRE PANEL)

2 Nos. 160Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.(MDB-01)

2 Nos. 63Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.(PLUMBING)

4 Nos. 40Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.(BOREWELL, LPDB, FEEDER PILLAR)

12 Nos. Three Phase Dual Type Digital Energy Meter with RS-485 Port & necessary

309 14 Set of LED ON/OFF Indication Lamp with 2A Fuse.

310 MR MAIN LT PANEL above & as per SLD Set 1 2443800 2443800

Automatic Power Factor Correction (APFC) System

Supply, Installation, testing and commissioning of Automatic Power Factor

Correction (APFC) panel, indoor type floor mounted free standing totally enclosed,

extendable, IP 42, of following capacity for 3 phase, 415 V + 10 %, 50 Hz AC System for

Ambient temperature -5°C to +40°C, fabricated in compartmentalized designed made of

CRCA sheet steel of 2.0mm thick for framework & covers, 3 mm thick for gland plate i/c

cleaning & finishing complete with 9 tank process for powder coated of approved shade

( RAL 7032-Siemens gray or as approved by Engineer-in-Charge), having front section

(switch gear and control accessories) and rear section capacitor and reactor, front and rear

access, having suitable current carrying capacity, extensible TPN Aluminum alloy bus bar

311 25.1 of high conductivity, DMC/SMC bus bar supports, bottom base channel of MS Section,

fabrication shall be done in transportable section, entire panel shall have common copper

earth bar of minimum size of 25mm x 5mm with 2 nos. earth studs, the earth terminals

provided on the body of capacitor bank shall also be bonded to the main capacitor panel

earth bus with 2 nos. 8 SWG or 6 SWG GI earth wires/ equivalent size of copper

conductor cable, forced ventilation for maintaining temperature rise not more than 5°C

from ambient, interconnections, connections with 14% detuned reactor and heavy duty

525 V ISI marked Impregnated MPP(Metalized Polypropylene) Capacitor (IS 13340 Part -

1 & 2) APFC Panel shall be in compliance with IS :16636 & CPWD Specifications etc. as

per below details

Suitable capacity MCCB Microprocessor base with O/C, S/C, E/L release of TPN 50KA

breaking capacity (Ics=Icu), ON, OFF, Trip, R, Y, B - LED Indicating Lamp set along

with required Instruments and accessories with extended rotary handle and door

interlocking arrangement. Current rating of the Incomer in ampere shall be APFC

Panel rating in KVAR x 1.4 x 1.5 or Nearest higher standards rating.

(B) Instruments & Indications

i) 3-Phase current sensing APFC microprocessor relay/controller , advance 8/12 stages (8

stages for capacity below 100 KVAR and 12 stages 100 KVAR & above) with

Communication Ethernet/RS485/SNMP port open protocol for BMS integration as per

approved by Engineering in charge and having display of Phase wise V, A, PF, Cos-Phi,

Kw, KVA, KVAR, THD-V , THD-I, harmonics up to 31 level. 3 nos of dual core CT's

accuracy class 1, 15VA at incomer of PCC Panel for APFC relay.

ii) Auto Manual Selector switch, auxiliary contactors with timer for delay in manual

iii) Digital Multi function meter with LED Display for V, A, PF, KW, KVA, KVAR,

THD-V & I, Frequency.

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

iv) Suitable rating control transformer shall be provided for control and

indication circuit.

v) All components like control transformer, meter, relay and indicating lamp shall be

protected by using suitable rating individual MCB's.

vi) Wiring of the control circuit shall be done by using 2.5 sq mm, FRLS 1100 V grade,

PVC insulated multi stranded copper control wire.

319 1.3 Amp per Sq.mm, TPN, Electrolytic grade Aluminum bus bar of capacity 1.25 times of

incomer rating as per CPWD specification.

(D) Outgoings (APFC Section)

Selection of the capacitors combinations shall be for continuous rating and each capacitor

bank shall have suitable capacity Heavy Duty ISI Marked Capacitor, capacitor duty

contactor, the capacitor shall be mounted on channel with base of perforated M S Powder

coated sheet, connections inter connections etc. and other features as per CPWD

Specifications and relevant IS Code having following:

(i) Capacitor bank ratings & stages shall be as per the technical specifications sheet of

(ii) Capacitor will be MPP self healing type with discharge resistor, pressure release

(iii) Since Capacitor Voltage is 525 Volts, thus higher KVAR has to be considered to get

rated output at 415 Volts.

(iv) 14% Detuned Reactor of class H insulation & 150% linearity in series with

(Note: Technical specifications sheet for selection of the capacitors combinations shall be

provided by the NIT Approving Authority with due consideration of number of capacitors

i.e. 1 KVAR, 2 KVAR, 3 KVAR, 5 KVAR, 10 KVAR.....for smooth correction).

326 25.1.4 125 KVAR above & as per SLD Set 1 320033 320033

Fabrication, supply, installation, testing and commissionings of cubicle type floor/ wall

mounted Main Distribution Board panel made out of 2.0 mm thick CRCA sheet

328 including connection, inter-connection alongwith 4 strip aluminium bus bar as per CPWD

specifications, ( Part IV - Sub-station) and IS: 8623 comprising of followings panel

mounting switchgears etc. as required.,

329 INCOMER FROM LT PANEL

1 Nos. 160Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.

Dual type Digital energy meter with RS485 showing V, A, PF, KVAR, KWH etc.

current transformers of 160/5A ratio, 10 VA Class 1.0 metering.

332 One (1) Set of Phase Indication & ON/OFF/TRIP Lamp with 2A SP MCB.

333 Control MCB'S, control terminals & wiring as required.

Under/ Over voltage, Master trip relays along with current transformers of 160/5A ratio,

10 VA class-5P10 protection - 1 set

335 Suitable arrangement to receive incoming armored cables.

336 Ameter with ASS

337 Voltmeter with VSS

338 ON/OFF/TRIP Indication

339 Open/Close Push button

340 Auto/Manual selector switch

200 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable

busbar insulation) supported by DMC / FRP insulators.

1 nos. 160A FP MCCB 35kA With Thermal Magnetic Based Release (O/C,S/C)

Protection & Rom (For Solar)

2 nos. 100A FP MCCB 35kA With Thermal Magnetic Based Release (O/C,S/C)

Protection & Rom (For Lift)

3 nos. 63A FP MCCB 35kA With Thermal Magnetic Based Release (O/C,S/C) Protection

& Rom (For UPS & Fire Pump at Terrace)

9 nos. 40A FP MCCB 35kA With Thermal Magnetic Based Release (O/C,S/C) Protection

& Rom (For Lighting & Power DB)

348 15 Set of LED ON/OFF Indication Lamp with 2A Fuse.

349 MR MDB-01 above & as per SLD Set 1 948151 948151

Fabrication, supply, installation, testing and commissionings of cubicle type floor/ wall

mounted Main Distribution Board panel made out of 2.0 mm thick CRCA sheet

351 including connection, inter-connection alongwith 4 strip aluminium bus bar as per CPWD

specifications, ( Part IV - Sub-station) and IS: 8623 comprising of followings panel

mounting switchgears etc. as required.,

352 INCOMER FROM LT PANEL

1 Nos. 630Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.

354 1 Nos. 630Amps, 415V FP CONTACTOR (AC-1 DUTY).

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Dual type Digital energy meter with RS485 showing V, A, PF, KVAR, KWH etc.

current transformers of 600/5A ratio, 10 VA Class 1.0 metering.

356 One (1) Set of Phase Indication & ON/OFF/TRIP Lamp with 2A SP MCB.

357 Control MCB'S, control terminals & wiring as required.

Under/ Over voltage, Master trip relays along with current transformers of 600/5A ratio,

10 VA class-5P10 protection - 1 set

359 Suitable arrangement to receive incoming armored cables.

360 Ameter with ASS

361 Voltmeter with VSS

362 ON/OFF/TRIP Indication

363 Open/Close Push button

364 Auto/Manual selector switch

365 BUS COUPLER

1 Nos. 630Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.

367 1 Nos. 630Amps, 415V FP CONTACTOR (AC-1 DUTY).

368 ON/OFF Indication

369 Open/Close Push button

370 Auto/Manual selector switch

371 INCOMER FROM 200 KVA DG PANEL

372 Incomer from DG Set shall be provided with the following:

1 Nos. 320Amps FP MCCB 50kA With Microprocessor Based release for O/C, S/C &

Earth Fault Protection.

374 1 Nos. 320Amps, 415V FP CONTACTOR (AC-1 DUTY).

Dual type Digital energy meter with RS485 showing V, A, PF, KVAR, KWH etc.

current transformers of 320/5A ratio, 10 VA Class 1.0 metering.

376 Control MCB'S, control terminals & wiring as required.

Under/ Over voltage, Master trip relays along with current transformers of 320/5A ratio,

10 VA class-5P10 protection - 1 set

378 Suitable arrangement to receive incoming armored cables.

379 Ameter with ASS

380 Voltmeter with VSS

381 ON/OFF/TRIP Indication

382 Open/Close Push button

383 Auto/Manual selector switch

384 Reverse power Protection Relay.

385 INTERLOCKING.

386 DG Incomer, Bus coupler and AMF logic, interlocking with main incomer.

800 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable

busbar insulation) supported by DMC / FRP insulators.

2 nos. 400A FP MCCB 35kA With Thermal Magnetic Based Release (O/C,S/C)

Protection & Rom

3 nos. 125A FP MCCB 35kA With Thermal Magnetic Based Release (O/C,S/C)

Protection & Rom

3 nos. 40A FP MCCB 35kA With Thermal Magnetic Based Release (O/C,S/C) Protection

393 8 Set of LED ON/OFF Indication Lamp with 2A Fuse.

394 MR MDB_HVAC above & as per SLD Set 1 1485140 1485140

395 MCCB BOX (UPS I/O PANEL)

Fabrication, supply, installation, testing and commissionings of FP MCCB Box made

out of 1.6mm thick CRCA sheet including connection, inter-connection as per CP WD

specifications, ( Part IV - Sub-station) and IS: 8623 comprising of followings panel

mounting switchgears etc. as required.,

397 63 Amps FP MCCB 25KA

398 MR MCCB BOX (UPS I/O PANEL) above & as per SLD Set 1 20299 20299

Fabrication, supply, installation, testing and commissionings of cubicle type floor/ wall

mounted Main Distribution Board panel made out of 2.0 mm thick CRCA sheet

400 including connection, inter-connection alongwith 4 strip aluminium bus bar as per CPWD

specifications, ( Part IV - Sub-station) and IS: 8623 comprising of followings panel

mounting switchgears etc. as required.,

1 Nos. 63 Amps TP MCCB With Double Neutral 25KA With thermal magenetic release

for O/C,& S/C Protection.

403 One (1) Nos. Three Phase Dual Type Digital Energy Meter with necessary CTs.

404 Protection Istrument

One (1) Nos. (0-500V) 96 x 96 Sq.mm voltmeter with control Fuse & selector switch.

1 Set of (0-60 Amps) 96 x 96mm CT operated Ammeter with 3 way selector switch and

407 One (1) Set of Phase Indication & ON/OFF Lamp with 2A Fuse.

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

200 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable

busbar insulation) supported by DMC / FRP insulators.

5 nos. 40A FP MCCB 16kA With Thermal Magnetic Based Release (O/C,S/C) Protection

412 5 Set of LED ON/OFF Indication Lamp with 2A Fuse.

413 MR UMDB above & as per SLD Set 1 176933 176933

414 LIFT PANEL

Fabrication, supply, installation, testing and commissionings of cubicle type floor/ wall

mounted Main Distribution Board panel made out of 2.0 mm thick CRCA sheet

415 including connection, inter-connection alongwith 4 strip aluminium bus bar as per CPWD

specifications, ( Part IV - Sub-station) and IS: 8623 comprising of followings panel

mounting switchgears etc. as required.,

1 Nos. 100 Amps FP MCCB 25KA With thermal magenetic release for O/C,& S/C

418 One (1) Nos. Three Phase Dual Type Digital Energy Meter with necessary CTs.

419 Protection Istrument

One (1) Nos. (0-500V) 96 x 96 Sq.mm voltmeter with control Fuse & selector switch.

1 Set of (0-100 Amps) 96 x 96mm CT operated Ammeter with 3 way selector switch and

422 One (1) Set of Phase Indication & ON/OFF Lamp with 2A Fuse.

200 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable

busbar insulation) supported by DMC / FRP insulators.

426 3 nos. 63A FP MCCB 16kA With TM Based Release (O/C,S/C) Protection & Rom

427 2 nos. 40A DP MCCB 16kA With TM Based Release (O/C,S/C) Protection & Rom

428 MR LIFT PANEL above & as per SLD Set 1 161528 161528

429 TOTAL OF SUBHEAD :8 320033 5235851

430 SUBHEAD :9_UPS

431 NOTE: Tentative Battery Rating for 10 kVA UPS in Ah=42

Online UPS- Input supply: Three Phase, Output supply: Three Phase

Supplying, installation, Testing & Commissioning of of following capacity at full

load (Unity Power Factor) at operating temperature 0 to 40 deg C, Relative humidity 0

to 95%, Online double conversion true sine wave Uninterrupted hot swappable (allow for

the replacement or addition of battery modules without shutting down the entire system)

modular Power Supply (UPS) system with N+1 modules (N denotes total number of

432 26.2 moduels requird for rated capacity). The UPS shall include a Rectifier, inverter, battery

bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600

VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA,

SMF in ABS Container) and Static Bypass switch alongwith provision for manual bypass,

suitable isolation transformer for additional protection against neutral faults etc. UPS shall

have inbuilt phase sequence correction.

The UPS systems offered are to be of the latest technology with Digital Control

Microprocessor based for reliable operation using Insulated Gate Bipolar Transistor

(IGBT)'s both for the rectifier & inverter (3 Level) with PWM (Pulse Width Modulation).

The quality of design,manufacturing and inspection process should confirm to the

relevant International standards such as IEC/EN/VDE. The operating efficiency of the

UPS systems shall be >96% while operating on battery mode and delivering quality power

to the 100% non-linear loads. Current total harmonic effect(ITHD) on the input grid shall

be < 5% at 50 %load. (The required LC (inductor (L) and a capacitor (C)) filters shall be

433 included in UPS cost), extreme power factor kit to be included to limit the input power

factor (PF) to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall

be kva rating x 1 ), however UPS shall be suitable to take load at 0.7 laging to 0.7 leading

power factor loads. UPS shall be suitable for incoming supply AC : 3Phase 400V +/-20%,

50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload capacity

of 120% for 10 mins, Sine wave output. Non condensing, noise level less than 60db at 1

meter distance, protections: Input Under voltage over voltage, abnormal out voltage,

battery over charging, output over current, short circuit protection,

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

battery deep discharge protection, 10KV surge. UPS must comply with low voltage

electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part

2, it shall be a Voltage and Frequency Independent (VFI)-type UPS. Communication

RS232/RS485/SNMP port open protocol for BMS integration, all hardware & software

for iOT Communication as per approved by Engineering in charge. Required battery

racks and interconnecting copper conductor cables of suitable size and connectors and all

required accoseries are inclusive of the cost). This system must provide a means for

logging and alarming of all monitored points plus email notification. Forced air-cooling

with integral inbuilt fans with redundancy (if one fan fail UPS should be able to handle at

least 80% of the load, Noise Level 65 DB at 1 meter distance. The system shall be in

compliance IEC 62040- 1,2 & 3, IS:16242 and CPWD Specification.

Display Panel (minimum) (In-build 5 inch or more LC Display / LED ) to display :

a) Input: Voltage, current, Frequency.

b) Bypass: Voltage, Frequency.

c) Output: Voltage, frequency, Current.

d) Battery: Voltage, Capacity.

e) Load: KVA, KW, Percentage.

f)Temperature: STS, Inverter, PFC.

g) Event Logging & Statistical Data (On LCD/LED): UPS should capture and display up

to 3000 events like: Over temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload /

Short-circuit / Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical

Data: No. of power failures / Transfers to Bypass / Total Running time, etc.

i) Mains Mode of Operation /Battery Mode of Operation / Bypass feeding the load /UPS

Fault /Battery charging and discharging, overload, battery voltage and battery capacity.

j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS Overload, Fault, Shutdown,

Input Over, Under Voltage, Output Over, Under Voltage, Battery Over, Under Voltage,

Over Load and short circuit, Over Temperature. The UPS should have QR code which

should contain drawing, test report OEM manual,Geo- Tag of manufacturing location etc.

436 26.2.1 10KVA (Each Power module shall be < 10 KVA) Each 1 208893 208893

437 TOTAL OF SUBHEAD :9 208893 0

438 SUBHEAD :10_EARTHING

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories,

439 5.4 and providing masonry enclosure with cover plate having locking arrangement and Each 10 8351 83510

watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories,

and providing masonry enclosure with cover plate having locking arrangement and

watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections

etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip

earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as

required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring

washer spaced at 50mm

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth

electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as

443 5.9 required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring Meter 60 160 9600

washer spaced at 50mm

444 TOTAL OF SUBHEAD :10 338314 0

445 SUBHEAD :11_LIGHTNING PROTECTION SYSTEM

446 Air Termination Network

Supply, Installation, testing and commissioning of single spike air terminals of 16/10 mm

dia. & 2000 mm length as required and as per site conditions. The air terminal shall be

manufactured with aluminium & shall be as per IEC 62561-2. The air terminal shall be

fixed with base plate arrangement.

Supply, Installation, testing and commissioning of 8 mm dia aluminium round conductor

448 MR for air termination network at parapet terrace level and shall meet the requirement of IEC Meter 312 158 49409

Supply, Installation, testing and commissioning of Parapet Conductor holder for holding

of 8 mm dia. round conductor (for RCC roof). The conductor holder shall meet the

requirements of IEC 62561-4.It should be installed at every 1 mtr.

Supply, Installation, testing and commissioning of 16sq.mm. copper cable along with lugs,

having 500mm length & as per IEC 62561-1 so as to connect air termination rod with any

metallic structure on the roof.

Supply, Installation, testing and commissioning of Universal Connector for making

451 MR straight, Tee & Cross joint of 8-10 mm Round Conductor to 8-10 mm dia Round Nos. 57 403 22977

conductor on parapet wall, roof and vertical facade of masonery / glass / metallic work.

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Supply, Installation, testing and commissioning of Expansion piece made aluminium & as

per IEC 62561-2 along with suitable connecting accessory. It shall be installed at every 20

mtr to maintain the flexibility to the conductor due to heat.

453 Down Conductor

Supply, Installation, testing and commissioning of 10 mm dia CBS round conductor for

454 MR Down conductors (100 Microns Copper Coating) to be installed in column. It shall meet Meter 216 533 115057

the requirements of IEC 62561-2.

Supply, Installation, testing and commissioning of Rebar Clamps for holding Down

455 MR Conductor of 10 mm diameter Copper bonded steel round conductor with Rebar Nos. 144 792 114020

complying as per IEC 62561-1. It shall be installed at every 1.5 mtrs.

Supply, Installation, testing and commissioning of Earthing stud/ Façade Stud of stainless

456 MR steel with clamp to connect down conductor with parapet conductor at terrace & meet the Nos. 10 1728 17276

requirement of IEC-62561-1.

Supply, Installation, testing and commissioning of Test link to disconnect the Round

down conductor from the earth termination network 10mm copper bonded steel for

regular checks of the earth termination resistance value. (with MS Enclosure concealed in

RCC column). It shall meet the requirements of IEC 62561-2.

Supply, Installation, testing and commissioning of Straight - Connector (for Down

conductors) for making straight joint of 10 mm CBS Round Conductor to 10 mm dia CBS

Round conductor in column. (Provided at every 3.5mtr)

Supply, Installation, testing and commissioning of Lightning Strike counter Model: JMV

7D for counting the number of lightning strikes without any power supply. The Counter

459 MR should be mounted on the Down Conductor. The Lightning Counter should be IP 68 rated Nos. 1 17276 17276

enclosure suitable for external application.

460 Earth Termination Network

Supply, Installation, testing and commissioning of Earthing termination made of copper-

bonded rod of 3mtr length,14.2 mm dia. (Minimum copper bonding shall be 0.25mm) as

per IS 3043, IEEE-80, NBC 2016 along with 25 kg/pit Earth enhancement material of

461 MR resistivity less than 0.12 ohm-mtr, and complying IEC 62561-7, SS clamp for terminating Nos. 10 8638 86379

the earth rod and Eco Guard Compact pit cover complying IEC 62561-5 and as per

specification and other applicable codes.

Supply, Installation, testing and commissioning of 10 mm CBS Conductor (250 Microns

Copper Coating) laid below the ground, as Required and as per specification and code of

463 Surge Protection Device

Supply, Installation, testing and commissioning of Class B/Type I Single-Phase Surge

Protection Devices The devices shall comply with IEC 62305-4 standards and be tested as

per IEC 61643-11. They should be DIN rail mountable and enclosed in a polycarbonate

464 MR enclosure with an IP 65 rating. These SPDs are required for installation at the main Nos. 1 17276 17276

distribution board or the entry point of the electrical installation to protect against high-

energy surges caused by direct lightning strikes or high-energy disturbances.

465 TOTAL OF SUBHEAD :11 0 855611

466 SUBHEAD :12_SOLAR PV POWER GENERATION

Solar Photovoltaic Power Plant

Supplying Installation, Testing and Commissioning of on-grid Solar Photovoltaic Power

Plant conforming to various applicable standards BIS, IEC, MNRE guidelines, the Central

Electricity Authority Regulations and CPWD Specifications as amended up

to date, consisting of Mono/Poly Crystalline silicon solar cells module, net metering

467 17.1 facility, necessary control, protections, earthing, cabling, mounting structure, junction

boxes, power conditioning units, Real time online web interfaced Data Monitoring

System, Distribution panels, grid connecting arrangement, conduits, pipes, cable trays and

other accessories etc. as required.

a) High Energy Efficiency Solar Photovoltaic Module of capacity 330 Wp or above,

manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-

Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be

less than 23% at STC with temperature coefficient of Pmax better than -0.30% per 0C.

PV modules used in solar power plants/ systems must be warranted for their output peak

watt capacity, which should not be less than 90% at the end of 10 years and 80% at the

468 end of 25 years. Solar Modules shall be designed to operate in relative humidity upto

100% with temperature between -10 0C and +85 0C. Further, each PV module used in

any solar power project must have Radio frequency identification tag with information

such as name of manufacturer, month and year of manufacturing, country of origin

(separately for Solar cell and module), I-V curve, Unique Serial No and Model No of the

module, Wattage, Im, Vm and FF, name of test lab issuing IEC certificate.

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

b)Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 415 V AC,

three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC with a

variation of 10% at nominal voltage. Power with efficiency not less than 97%, total

harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 0C,

Minimum IP-65 for outdoor and Minimum IP 21 for indoor, Built-in meter and data

logger, MPPT, switching devices IGBT/MOSFETs and controller Microprocessor /DSP.

PCU/inverter shall be capable of complete automatic operation including wake-up,

synchronization & shutdown. The PCU shall be able to withstand unbalanced load

conforming to IEC standard with shutdown/standby mode. It must be provided with grid

islanding along with manual disconnect pole isolation switch besides automatic

469 disconnection. Minimum protections: Mains Under / Over Voltage, Over current,

Over/Under grid frequency, Over temperature, Surge voltage induced at output due to

external source, Short-circuit, Lightening, Anti Islanding (for grid synch. Mode) and other

protections as per applicable standards. LCD/LED display of minimum parameters:

DC input voltage, DC current, AC Voltage and current (all 3 phases, in case of 3 phase),

Instantaneous & cumulative AC output power, Daily DC energy produced and other

parameters applicable standard. Communication interface RS 485 / RS 232.

c) Module mounting structure: The roof top solar plant generation units shall be installed

by using supporting Aluminium/Galvanized MS structure (mass of zinc coating shall be as

per IS4759 ) having minimum head room clearance of 2.4 meter above the terrace level /

ground level. The mounting structure would be designed to sustain wind load and seismic

parameter of the site of installation. All the structure shall be design as per applicable BIS

code and the material shall also confirm the applicable BIS Code. Structural material shall

be corrosion resistant and electrolytically compatible with the materials used in the

module frame, its fasteners, nuts and bolts. The suitable arrangements for maintenance

and cleaning shall be provided.

d) Real time online web interfaced Data Monitoring System complete with accessories for

various parameters such as Solar Irradiance, temperature, AC Output Voltage and current,

471 Output Power, Power factor, DC Input Voltage and Current, Time Active,

Time disabled, Time Idle, Power produced and other parameters as per standard practices.

e) Array junction box & Main junction box with IP 65 protection and termination

arrangement for incoming and outgoing cable along with glands, lugs and other

accessories etc. as required. Each junction box shall be made of GRP/FRP/Powder Coated

Aluminium /cast aluminium alloy with full dust, water & vermin proof arrangement with

High quality Suitable capacity Metal Oxide Varistors(MOVs) (semiconductor diode with

resistant applied voltage)/ surge arrestors and suitable Reverse Blocking Diodes, isolation

switches isolate the DC input to Inverter, copper bus bar etc.

473 f) Lightning, surge voltage protection, earthing protection and grid islanding.

g) Cables: Connections & Interconnections by required size IR/UV protected XLPE

insulated copper conductor 1.1 kV grade armored power and control cables(ISI Marked)

along with supplying & fixing of necessary channel/conduit, GI cable trays, supports,

lugs, thimble and other accessories etc. as required.

h) DC Distribution Board And AC Distribution Panel Board: IP65, free standing, metal

475 cladded, having copper bus bar, having required protection and control gears, connection-

interconnection, etc. as required.

476 SOLAR PHOTOVOLTAIC as described above kWp 70 54280 3799600

477 TOTAL OF SUBHEAD :12 3799600 0

478 SUBHEAD :13_FIRE ALARM SYSTEM

479 28.2 INTELLIGENT FIRE ALARM SYSTEM

Supplying, installation, testing and commissioning of micro processor based intelligent

addressable main fire alarm panel, central processing unit with the following loop

modules and capable of supporting not less than 240 devices (including detectors) and

minimum 120 detectors per loop and loop length up to 2 km, network communication

card, minimum 320 character graphics/ LCD display with touch screen or other keypad

and minimum 4000 events history log in the non volatile memory (EPROM), power

supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free

batteries with automatic charger. The panel shall have facility to connect printer to

printout log and facility to have seamless integration with analog/digital voice evacuation

system (which is part of the schedule of work under SH: PA System) and shall be

complete with all accessories . The panel shall be compatible for IBMS system with open

protocol BACnet/ Modbus over IP complete as per specifications.

Supplying, installation, testing & commissioning of repeater panel wih 320 character/

482 28.2.3 Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete Each 1 113734 113734

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Supplying, installation, testing & commissioning of central graphical fire alarm

management system to centrally monitor and operate the fire alarm system as required.

Supplying, installation, testing & commissioning of intelligent analog addressable

photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on

485 28.2.5 surface/recessed MS Box having two LED, metallic cover complete with all connections Each 101 306 30906

etc as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as

Supplying, installation, testing & commissioning of intelligent addressable thermal

487 28.2.9 detector with rate of rise cum fixed tempreature thermistor complete with base as Each 2 2866 5732

Supplying, installation, testing & commissioning of addressable manual call point

complete as required.

Supplying, installation, testing & commissioning of addressable fire control module

complete as required

Supplying, installation, testing & commissioning of addressable horn cum strobe complete

Supplying, installation, testing & commissioning fire fighter telephone handset complete

Supplying, installation, testing & commissioning fire fighter phone jack complete as

Supplying, installing, testing & commissioning of approved make Addressable Monitor

Module for Sprinklers, Panic Bars & other Third Party Inputs. The monitor module shall

monitor potential free contacts. The device shall have an LED which shall blink in normal

state & get steady on activation to monitor the heath status of the device. Addressing shall

be with user friendly rotary decimal switches. Module shall be supplied with mounting

plate from OEM for ease of installation & maintenance.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with

494 28.5.2 annealed copper conductor having XLPE insulation, steel wire armouring & FRLS/HFFR Meter 450 192 86400

outer sheath complete as required.

Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor,

single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and Fixing of following sizes of steel conduit along with accessories in surface/

497 1.20 recess including cutting the wall and making good the same in case of recessed conduit as

499 TOTAL OF SUBHEAD :13 2233768 27209

500 SUBHEAD :14_PUBLIC ADDRESS SYSTEM

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with

501 28.3.1 USB, MP3 player (including 6 zone button paging station) with seamless integration Each 1 132115 132115

facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall

speakers complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V

rms operating at 240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with

microphone assembly complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in

505 28.5.3 the existing surface / recessed steel conduit of following pairs, cores and size including

connections and interconnections etc. as required.

506 28.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm Meter 1500 61 91500

Supplying and Fixing of following sizes of steel conduit along with accessories in surface/

507 1.20 recess including cutting the wall and making good the same in case of recessed conduit as

Supplying and Fixing 25 mm dia MS flexible pipe with PVC coating along with all

ancillaries and accessories like coupler etc. as required.

510 TOTAL OF SUBHEAD :14 972152 0

511 SUBHEAD :15_DATA & VOICE SYSTEM

512 SECTION - I- STRUCTURED CABLING SYSTEM PASSIVE

Supplying and drawing following core Fiber Optic Cable having corrugated steel

armoring. The Fiber should be SM Fiber Central -loose tube filled with Thixotropic jelly,

duly following Standards: ISO 11801, IEC 60793-1/60794-1-2, ITU-T-REC G.652D and

513 39.19 Telecordia GR-20-core, High quality Electro Chromium Coated Corrugated Steel tape

(ECCS ) and HDPE- Sheath, Operating ambient Temperature should be – 5 0C to +50 0C

and Storage Temperature shall be – 5 0C to +50 0C, Max Attenuation ± 0.36 (db / km) at

Operational Wavelength 1310 nm and ± 0.22

514 39.19.1 Single Mode 6 Core Optical fiber cable Meter 100 64 6400

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Supply and fixing following port Rack Mount loaded LIU with pigtail, Front-mounted

cable saddles for jumper management, suitable to manage both splices and terminations,

Pre-assembled shelves in multiple configurations, Rubber fiber slotted bracket built-in,

metal splice shelf to protect the fibers, 2 fiber spools built-in for 900μm tight buffered

fiber storing, Capable of storing up to 3 meters of 900μm tight buffered fiber per adapter,

Removable front and rear covers for better access to interior of LIU, Should be Single /

Multi mode LC Type fully loaded. Accessory kit consists of cable ties, mounting ear

screws, and spiral wrap tube etc complete as required.

Supplying and fixing Patch Cord of Optical Fiber Multi Mode or Single Mode LC to LC

Fiber Duplex having high precision ceramic ferrule with good concentricity, Fiber

corning single mode G652D, Cable Type 2mm with Mechanical specification Apex

Offset < 50 μm, Fiber Height + 100 nm, End-face radius of Curvature 7mm < R <25mm,

Repeatability < 0.2 db, Working ambient Temperature – 5 0C to +50 0C, Storage

Temperature – 10 0C to +50 0C, Length -- 2meter, Type -- LC-LC Duplex etc complete as

Supplying Installation Testing and Commissioning of 24 port Cat6 Patch Panel loaded.

Must be of 1U height with clear label holders and white label with the panel.24 Ports Cat-

6 Patch Panel should have ETL/UL verification program certificate for compliance with

ANSI/TIA-568.2-D etc. complete as required.

Supplying, Installation, Testing and commissioning of following CAT6A Patch Cord

519 39.13 should have ETL/UL verification program certificate for compliance with ANSI/TIA-

568.2-D etc. complete as required.

520 39.13.1 Copper Patch Cords of length 1m (3ft) Each 113 173 19549

521 39.13.2 Copper Patch Cords of length 3m (10ft) Meter 113 405 45765

Supplying, Installation, Testing and commissioning of CAT6A Copper Information Outlet

(IO) with face plate of color as per site requirement, should have ETL/UL verification

522 39.15 program certificate for compliance with ANSI/TIA-568.2-D. All copper Cable and Each 113 302 34126

Components should be from same OEM to maintain compatibility and interoperability etc.

complete as required.

Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid

copper cable in existing conduit/ on surface, U/FTP, LSZH, Non- Plenum, Horizontal

(solid) Cable suitable for high speed data networking application supporting upto

10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP) cable with

523 39.18 color coded insulation for easy indentification should have FLAME PROPERTIES i.e.

Flammability Test - IEC 60332-1, Smoke Density - IEC 61034, LSZH standards

compliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew

should be < 45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable should have

been tested and verified by UL/ ETL etc. complete as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover

plate for modular switches in recess etc. as required.

Supplying and fixing 42U Rack with 6 inch Castor wheels and front brake Floor Standing

Rack with Main Frame Pillar of 1.6mm CRCA Sheet with removable side panels, L-

Shape adjustable Vertical Mounting Rail of 2mm with 'U'Marking completely knocked-

down condition (CKD) Shape, fitted with 4 number cooling fans, minimum 8nos two line

cable entry/exit provision at top and bottom with rubber protection, Front door 5mm

Toughened Glass with MS frame or MS perforated with lock, Rear MS vented or

perforated door, Powder coated Color- RAL- 7035 or black, complied with UL & RoHS,

2 x 6 sockets 16A power distribution units, 3 numbers closed cable organizer, Hardware

mounting screws packet of 20 x 1 number, etc. complete as required.

528 SECTION - II- IP-PBX SYSTEM

Supplying, installation, testing and Commissioning of IP based voice communication

system with 04 Port Voicemail, 04 Port FXS, 04 Port FXO, 1 PRI Trunk lines (30

Channels) Circuit with CLIP Facility, min 100 IP users License with provision for further

additions, 100 analog users, 01 Number IP based Operator Console, 100 Party

529 38.1 Conference, Speed Dial, Music on Hold, Internal/ External ring difference, Call Barring, Each 1 1578920 1578920

Call Pickup, Redundant server in active -Active mode and as per technical specification

including supporting accessories etc complete as required. The system should have valid

TEC GR approval from DoT.

Supplying, Installation, Testing & Commissioning of Analog phones having standard

530 38.4 feautres like 16 digit LCD display, 2 way speaker, caller ID and number storage facility Each 34 1544 52496

etc. complete as required.

531 SECTION - III- LOCAL AREA NETWORK ( LAN )

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Supplying, installation, Testing and commissioning of 10 Giga Bandwidth Data Centre

Network Switch of 48 port Layer 3 having features and specifications etc. as mentioned

here under: - ToR/EOR/Core Network Switch 48x 10GbE SFP+, 6x 100GbE QSFP28,

RPS, with Console Port, Management Port and 1 x USB 2.0 Type A port, The switch

must provide a switching capacity of no less than 2.16 Tbps and a forwarding rate of at

least 1600 Mpps, ensuring non-blocking performance for high-bandwidth applications. It

should support hot-swappable dual power supply modules (AC or DC) for 1+1

redundancy and load sharing, as well as hot-swappable, front-to-back airflow fan trays

with N+1 redundancy to ensure continuous availability. IEEE 802.1X support for port-

based and MAC-based authentication should be available, along with integration for

RADIUS and TACACS+ authentication services. Guest VLANs, DoS prevention, and

management access restrictions are essential. SNMP v1/v2c/v3, syslog, sFlow, and

support for autoconfiguration via DHCP. Support for OpenFlow v1.4, Netconf/YANG,

and LLDP is required for modern network automation. Support ONIE (Open Network

Install Environment), IEEE 802.1Q bb Priority-based Flow Control (PFC), OpenFlow

v1.4, ERPS, IPv6 Tunneling, IP interfaces and supported, VXLAN, Private VLAN,

Multicast VLAN, Guest VLAN Double VLAN (Q-in-Q), RoCEv2, PIM-SSM/SM,

MSDP. Support High Availability with MLAG/VSS and Layer 2/3 VPNs Critical for

Multi-tenant, Virtualized, and Containerized Environments. BGPv4/v6, OSPFv2/v3,

IS-IS, RIPng. VRRP, ECMP, BFD, and route redistribution for high-availability routing.

Support flexible routing domains and secure inter-segment traffic flow. Certifications:

FCC, MTCTE, OEM/Product must be on Trusted Telecom Portal of Department of

Telecommunication, Government of India etc. complete as required.

Supplying, installation, Testing and commissioning of following capacity 24 port Layer 2

indoor Network Switch having features and specifications etc. as mentioned here under:

At least 24 X RJ-45 Gigabit Ethernet Ports and additional 2 X 10G Base -T with 4 X SFP

Ports with non-blocking architecture by having Switching capacity of min. 168Gbps and

packet forwarding rate of 125Mpps or higher, 16K MAC table. Console Port, USB port,

Stacking support of min. 8 units per stack. Internal dual AC Power supply, STP,

RSTP, MSTP, BPDU Filter, BPDU Restriction, Min. 9K Jumbo Frame, LBD, IGMP

Snooping V1/V2/V3, MLD Snopping V1/V2. IGMP /MLD Groups 1K or more,

IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6 ND, VRRPv3, UDP Helper,

ECMP. VLAN: 802.1Ǫ, Port based, Ǫ-in-Ǫ, Multicast VLAN, Protocol VLAN,

VLAN Trunking, DHCP Snopping, Server, server Screening. RADIUS , TACACS+

Authentication, ǪoS: 802.1P, 8 queues per port, ǪoS : WRR, Strict+WRR, WRED,

802.1p. ACL: MAC based, IPv4C IPv6, TCP/UDP Port number, time based ACL, TFTP

Client, SNMP V1, v2c, v3, SNMP traps, RMON, DHCP server, relay, client, LLDP,

LLDP-MED, OAM, Dying Gasp, 802.3ah, sflow, RIP, OSPF v2/v3, policy based route,

SSL, SSH. 6 kV surge protection on all Gigabit Ethernet ports and on all GE RJ-45 access

ports. Certifications: UL, CE, FCC, RoHS, MTCTE, OEM/Product must be on Trusted

Telecom Portal of Department of Telecommunication, Government of

India etc. complete as required.

24 port PoE Layer 2 Network Switch with PoE Support of 370W or higher with each

copper port supporting 802.3at PoE+ min.

Supplying, Installation, Testing and commissioning of small form-Pluggable (SFP) for

535 39.6 Network Switches. Must be hot Pluggable, RoHS Complaint, etc. complete as required.

536 39.6.1 1G SFP Single Mode/Multi Mode Nos. 2 4211 8422

537 39.6.3 10 G SFP + Single Mode/Multi Mode Nos. 2 14972 29944

Supplying, Installation, Testing and commissioning of indoor Wireless Access Point for

High density use having features and specifications etc. as mentioned here under- WiFi6

802.11ax 574Mbps (2.4GHz) + 2402Mbps (5GHz), WIFI 6 Certified, 1 x RJ45 console

port, MG 2.5G LAN POE Port, factory reset, WPA/WPA2/WPA3™ Personal/Enterprise,

WEP 64/128-bit, SSID broadcast disable, MAC address access control, Internal RADIUS

server, SNMP, Customizable Captive Portal, Auto Channel, Works as Access Point,

WDS, WDS with AP, Wireless Client ., Web (HTTP), Secure Socket Layer (SSL),

Traffic control, Support ATF/Fast Roaming/Band Steering, Supports enhanced security –

WPA-PSK/WPA2- PSK/WPA3-PSK and RADIUS client, and Cipher negotiation, and

MAC/ IP ACL for networks, Certifications: MTCTE, CE, FCC. Works as Standalone,

Compatible with S/W & H/W Controller with addtional features like - Real-Time

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Supplying, Installation, Testing and commissioning of indoor Wireless Access Point for

Low Density use having features and specifications etc. as mentioned here under - Dual-

band Wi-Fi6 (802.11ax) 574Mbps (2.4GHz) + 1200Mbps (5GHz), WI-FI 6 Certified, 1 x

RJ45 console port, 1G LAN POE Port, factory reset, WPA/WPA2/WPA3™

Personal/Enterprise, WEP 64/128-bit, SSID broadcast disable, MAC address access

control, Internal RADIUS server, SNMP, Customizable Captive Portal, Auto Channel,

Works as Access Point, WDS, WDS with AP, Wireless Client, Web (HTTP), Secure

Socket Layer (SSL), Traffic control, Support ATF/Fast Roaming/Band Steering, Supports

539 39.7 enhanced security – WPA-PSK/WPA2- PSK/WPA3-PSK and RADIUS client, and Nos. 1 22739 22739

Cipher negotiation, and MAC/ IP ACL for networks, Certifications: MTCTE, CE, FCC.

Should also work as Standalone and must be Compatible with S/W & H/W Controller

with addtional features like - Real-Time Monitoring and Alerts, Rich Advanced Features,

Centralized Device Management, Role-Based Administration, Real-Time Monitoring,

VLAN and Access Control, Auto RF Management and Bandwidth Optimization, Multi-

SSID and Captive Portal Authentication.OEM/Product must be on Trusted Telecom

Portal of Department of Telecommunication, Government of India etc. complete as

Supplying and Fixing of following sizes of steel conduit along with accessories in surface/

540 1.20 recess including cutting the wall and making good the same in case of recessed conduit as

542 TOTAL OF SUBHEAD :15 5994320 0

543 SUBHEAD :16_CCTV SYSTEM

Supplying, installation, Testing and commissioning of following capacity 24 port Layer 3

Network Switch having features and specifications etc. as mentioned here under: At least

20 X RJ-45 Gigabit Ethernet Ports and additional 4 combo 10/100/1000 base-t/SFP Ports

with additional 4 SFP+ ports non-blocking architecture by having Switching capacity of

min. 128Gbps and packet forwarding rate of 95Mpps or higher, 16K MAC

table. Console Port, USB port, Internal AC Power supply with operating temperature of 0

to +50 0C. Stacking port with stacking support of minimum 8 units per stack. 48K Mac

address, 9K or more Jumbo frame, ERPS with enabling ring to converge in less than 50

ms from node or link failure, Static routing, Static, 6to4, ISATAP and GRE, IPv6

Neighbor Discovery (ND), BGP, ISIS, MPLS, VRRP v2, OSPFv2/v3, PBR, Route

Redistribution, RIPv1/v2/ng, IP Helper all L3 Protocols should support from day 1

for both IPv6 and IPv4, 802.1x, Port security , Radius C TACACS+ authentication C

accounting, DAD, DAI, DoS attack prevention, SSH, Guest VLAN, IP Access

List, MAC Access List. Multicast: VLAN, PIM-SM, PIMDM, PIM- SDM, PIM-SMv6,

DVMRP v3 and MSDP, IGMP C MLD Snooping, Flow mirroring, IGMP C MLD

Snooping Ǫuerier, Per-VLAN IGMP C MLD Snooping. SNMP, Dual configurations,

Multiple images, RMON, LLDP/LLDP-MED, sFlow, DHCP/BOOTP Client, IPv4/IPv6,

Syslog server, Debug command, 802.3ah Ethernet Link OAM, 802.1ag Connectivity

Fault, Y.1731 OAM, 802.1Ǫbb Priority- based Flow Control

(PFC), Dying Gasp, Cable Diagnostics , 6 kV surge protection on all Gigabit Ethernet

ports and on all GE RJ-45 access ports. Certifications: UL, CE, FCC, RoHS, MTCTE,

OEM/Product must be on Trusted Telecom Portal of Department of Telecommunication,

Government of India etc. complete as required.

Supplying Installation Testing and Commissioning of 24 port Cat6 Patch Panel loaded.

Must be of 1U height with clear label holders and white label with the panel.24 Ports Cat-

6 Patch Panel should have ETL/UL verification program certificate for compliance with

ANSI/TIA-568.2-D etc. complete as required.

Supplying, Installation, Testing and commissioning of following CAT6 Patch Cord should

546 39.12 have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D

etc. complete as required.

547 39.12.1 Copper Patch Cords of length 1m (3ft) Each 41 151 6191

548 39.12.2 Copper Patch Cords of length 3m (10ft) Each 41 227 9307

Supplying, Installation, Testing and commissioning of CAT6 Copper Information Outlet

(IO) with face plate of color as per site requirement, should have ETL/UL verification

549 39.14 program certificate for compliance with ANSI/TIA-568.2-D. All copper Cable and Each 41 212 8692

Components should be from same OEM to maintain compatibility and interoperability etc.

complete as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover

plate for modular switches in recess etc. as required.

552 40.5 5/6MP IP IR Dome Camera

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Supplying Installation Testing and Commissioning of 5/6MP IP IR Dome Camera having

following specifications and features etc :-

1)Type of Camera: Dome Camera

2) Image Sensor: 1/2.8" or better progressive Scan

CMOS get color image even at night condition

3) Signal System: PAL/NTSC

4) Minimum Illumination: 0.008Lux@ F1.4, AGC ON, 0

lux with IR or better

5) Imaging: 1/3s to 1/30000s Shutter Support, Auto

Gain Control , White Balance- Auto, Back Light

Compensation, Multi zone Privacy Masking, HLC,

553 Digital Watermarking.

6) On Screen Display: Camera should display Camera

title, Date & Time in live & recorded video both.

7) Signal to Noise Ratio: > 50 dB

8) Day & Night: True Day & Night High Performance

Mechanical IR cut filter with auto switch, IR Source-

Inbuilt IR LED's with effective distance upto 50 Mtrs

integrated IR 30 Mtrs for colour view in night.

9) Video Compression (Minimum): H.265 or better,

Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723

10) Wide Dynamic Range: WDR (120dB or more)

11) Digital Noise Reduction: DNR (2D/3D) On/Off

12) Streaming: Triple streaming, configurable

13) Video Streaming & Frame Rates: Triple streaming , configurable Main stream: 5/6MP

@25/30 fps, Sub streams: D1@25/30 fps or better

14) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable

through client software or web browser

15) Profile Management: User configuration import, export

16) Security: User Authentication, Water Marking

17) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot

upto 512 GB. It should be supplied with minimum 128GB memory Card.

18) Recording Management: Format SD, overwrite, storage management, video to NAS

19) Edge Analytics : Tripwire, Intrusion, Motion Detection

20) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP

conflict detection; memory card state detection; memory space detection

21) Alarm Support: It should have 1/1 Alarm In/ Out Port

22) Audio Support: It should have 1x Built-In Mic and 1/1 Audio In/ Out Port for external

Mic. and Speaker (As per site requirement) with G.711U/A/ G.711Mu/

AAC/ G.726 audio compression

23) Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP

TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast,

24) System Capability: ONVIF

25) VMS: Camera shall support open source VMS

26) Cyber Security: trusted boot, AES 256-bit Encryption, Configuration encryption,

trusted execution, Digest, security logs, , account lockout, video encryption, IP/MAC

filtering, HTTPS, trusted upgrade.

27) Ethernet: 1 RJ 45 10/100 Ethernet port

28) Power Input: The camera should support simultaneous dual power input—12 VDC

(via power adapter) and PoE—to ensure continuous operation in the event of a failure in

one power source.

29) Power Requirement: 12VDC/24VDC/PoE (802.3af)/ePoE

30) Enclosure: IP67 weather proof, IK10

31) Operating Condition: Ambient Temperature:- (-) 05°C to 50°C, humidity 95% (max)

(non-condensing)

32) IR life: 40000 hours or higher

33) Video Bit rate: 32 KBPS - 8 MBPS or better

34) Standards: BIS with ER, STQC Certified, CE, FCC

5MP/6MP IP IR 2.7 to 4 mm ~12 to 13.5mm or better Varifocal Motorized lens Dome

557 40.6 5MP /6MP IP IR Bullet Camera

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Supplying Installation Testing and Commissioning of 5MP/6 MP IP IR Bullet Camera

having following specifications, type of lens and features etc :-

1) Type of Camera: Bullet Camera2) Image Sensor: 1/2.8" or better progressive Scan

CMOS get color image even at night condition

3) Signal System: PAL/NTSC

4) Minimum Illumination: 0.008Lux@ F1.4, AGC ON, 0

lux with IR or better

5) Imaging: 1/3s to 1/30000s Shutter Support, Auto

Gain Control , White Balance- Auto, Back Light

Compensation, Multi zone Privacy Masking, HLC,

Digital Watermarking.

6) On Screen Display: Camera should display Camera

title, Date & Time in live & recorded video both.

7) Signal to Noise Ratio: > 50 dB

8) Day & Night: True Day & Night High Performance

Mechanical IR cut filter with auto switch, IR Source-

Inbuilt IR LED's with effective distance upto 50 Mtrs

integrated IR 30 Mtrs for colour view in night.

9) Video Compression (Minimum): H.265 or better,

Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723

10) Wide Dynamic Range: WDR (120dB or more)

11) Digital Noise Reduction: DNR (2D/3D) On/Off

12) Streaming: Triple streaming, configurable

13) Video Streaming & Frame Rates: Triple streaming , configurable Main stream: 5/6MP

@25/30 fps, Sub streams: D1@25/30 fps or better

14) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable

through client software or web browser

15) Profile Management: User configuration import, export

16) Security: User Authentication, Water Marking

17) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot

upto 512 GB. It should be supplied with minimum 128GB memory Card.

18) Recording Management: Format SD, overwrite, storage management, video to NAS

19) Edge Analytics : Tripwire, Intrusion, Motion Detection

20) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP

conflict detection; memory card state detection; memory space detection

21) Alarm Support: It should have 1/1 Alarm In/ Out Port

22) Audio Support: It should have 1x Built-In Mic and 1/1 Audio In/ Out Port for external

Mic. and Speaker (As per site requirement) with G.711U/A/ G.711Mu/

AAC/ G.726 audio compression

23) Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP

TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast,

24) System Capability: ONVIF

25) VMS: Camera shall support open source VMS

26) Cyber Security: trusted boot, AES 256-bit Encryption, Configuration encryption,

trusted execution, Digest, security logs, , account lockout, video encryption, IP/MAC

filtering, HTTPS, trusted upgrade.

27) Ethernet: 1 RJ 45 10/100 Ethernet port

28) Power Input: The camera should support simultaneous dual power input—12 VDC

(via power adapter) and PoE—to ensure continuous operation in the event of a failure in

one power source.

29) Power Requirement: 12VDC/24VDC/PoE (802.3af)/ePoE

30) Enclosure: IP67 weather proof, IK10

31) Operating Condition: Ambient Temperature:- (-) 05°C to 50°C, humidity 95% (max)

(non-condensing)

32) IR life: 40000 hours or higher

33) Video Bit rate: 32 KBPS - 8 MBPS or better

34) Standards: BIS with ER, STQC Certified, CE, FCC

5MP/6MP IP IR 2.7 to 4 mm ~12 to 13.5mm or better Varifocal Motorized lens outdoor

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

Supplying Installation Testing and Commissioning of following Channel Network Video

Recorder (NVR) with camera licenses to record for all channels having specifications

and features etc as mentioned below :

1) Network Video Recorder Embedded/ Installed OS

(Linux) along with Camera Licenses to record per NVR and to provide a live view,

storage and simultaneously Multi-channel playback of all IP camera or more and must be

ONVIF with minimum support of 384 Mbps incoming Bandwidth.

2) NVR should support video compressions : H.265 or better, H.264, MJPEG.

3) Must support 1 channel RCA Input, 2 channel RCA Output for Two-way Talk with

G.711U/A, G.711u, PCM, G726 audio compressions.

4) Intelligent auto power on when power resumes after power outage.

5) Storage: It should support minimum 8 SATA Slots with 20TB capacity/ Slot and RAID

562 40.11 support of RAID 0/1/5/6/10.

6) Connectivity Interface : 2 Nos. x 10/100/1000 Mbps Ethernet Ports, 1x RS485, 1x

RS232, 1x eSATA Port

7) Backup Interface : Its should have 4 Nosx USB port (2x USB3.0, 2xUSB2.0)

8) Video Output Ports: 2x HDMI and 2 VGA

9) Alarm Ports: It should have 16/8 Ch In/ Out ports to connect various type of external

sensors and output devices like hooter/ Siren etc.

10) Email & SMS Altert options: Option for SMS/ Email Alerts to minimum 5 designated

mobile number for power failure, HDD failure, vandalism, tempring, network

disconnection and panic

11) Web & Mobile Application: Web, Mobile app ( For iPhone, iPad, Android Phone) for

alerts and viewing.

12) Protocols: HTTP, HTTPS, TCP/IP, IPv4/IPv6, UDP, DHCP, DNS, SMTP, UPnP, IP

Filter, PPPoE, FTP, DDNS, Alarm Server, IP Search, Multicast, Auto Registration,

ONVIF (Profile T, Profile S, Profile G), CGI, SDK and OEM Cloud for remote

monitoring without any public IP need.

13) Standards: CE, FCC, RoHS, BIS Certified

14) Power Supply : Should support AC100-240V, 50/60Hz Power supply.

15) Operating Condition : -5°C to 50°C, humidity 90% (max) (non-condensing)

16) The VMS application shall support all the features & functionalities of the offered

17) VMS should consist Licenses for all channels to record Cameras with General,

motion detection, intelligent, alarm and POS recording modes. VMS should be provided

with Camera Licenses , with no dependency of VMS licenses by binding with the MAC

563 address of the cameras to achieve the functionality.

18) The NVR OEM shall be responsible for providing a mobile application compatible

with both Android and iOS devices, enabling remote monitoring and playback of

cameras/NVR footage.

19) The OEM must provide its own DDNS server hosted in India, eliminating the need

for a public IP address for remote monitoring over the Internet.

20) Must support Continuous, Alarm, Motion, Instant, Panic Recording Mode

21) It should support Resolution: 32MP; 24MP; 16MP; 12MP; 8MP; 5MP; 4MP; 1080p;

720p; D1; CIF; QCIF

22) When alarm recording is enabled and an event occurs, you can click the alarm icon on

monitoring page to view the alert details. The snapshot function is supported on

monitoring and playback page

23) The Network Video Recorder (NVR) shall be configured to send email whenever a

system message is created or an alarm event occurs. The email server shall be a valid

SMTP server. Each recipient email address shall be configured to receive any

combination of critical, warning, or informational messages or alarm notifications. When

an alarm occurs, the email message includes the NVR name, time of alarm and a list of

camera that is configured to record upon alarm

24) It should have Web and GUI interface.

25) Built-In Artificial Intelligence: NVR should have built-in AI :- - 2 Channel face

detection and recognition, - Minimum 4 Channel perimeter protection, - Minimum 8

Channel Smart Motion Detection

564 26) Face Recognition Database Capacity: It should support total Blacklist and Whitelist

capacity of Minimum 20,000 Faces or more with Face Detection speed of 12 face

images/sec and facility to add Name, gender, birthday, address, credential type, credential

No., countries & regions and state to each face image.

27) Face & Human Attributes Search: Search Pictures/ Video by Gender, age group,

glasses, expressions, face mask, beard, Top color, top type, hat, bag, age, gender and

28) ANPR Capability: It should support ANPR Camera with License plate, plate color,

vehicle body, vehicle model, vehicle logo, calling, seatbelt, vehicle registration location

etc vehicle attributes.

Digitally signed by SUPARNA

S. ITEM UNIT AMOUNT (IN RS.)

DESCRIPTION UNIT QTY

NO. NO. RATE DSR 2025 MR

29) Alarm Notifications based on: Motion detection, video tampering, video loss, scene

changing, PIR alarm, Camera external alarm, Face detection, face recognition, perimeter

protection (intrusion and tripwire), ANPR, people counting, stereo analysis, crowd

distribution, heat map, Disk Full, Storage Error, IP Conflict and abnormal behavior of fan,

cybersecurity exception

30) Alarm Notification should be linked with Recording, snapshots, Camera external

alarm output, buzzer, logs, presets and email.

565 31) General AI Based Search: Search Pictures by channel, time, event type, target

classification (Fall Detection, People Approach Detection, People No. Exception

Detection, People Staying Detection, Violence Detection.

32) Smart playback function: Should support smart search for the selected area in the

video and smart playback to improve the playback efficiency

33) VCA (Video Content Analytic): Should support multiple video contented analytics

based on camera analytics

34) Analytics by NVR: Perimeter protection and face recognation

64 Channel Network Video Recorder (NVR) having display split :- Main screen: