REPAIRS TO ROADS, PATHS, CULVERTS AND GATES AT ZONE-I AREA UNDER GE MCEME, SECUNDERABAD

Amount

Repar to potholes any depth, not exc 1sq m each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth making good by applying tack coat @5kg/10sqm, putting in premixed bituminous mecadam, well rammed and sealed with binder 9.8kg per 10sqm, blinded with 0.09cum of stone chippings, 6.3mm size and again well rammed(including supply of premixed macadam, binder and chippings) depth of pot holes not exc 30mm all as specified and as directed.

M&L for bituminous premixed semi-dense asphaltic concrete 30 mm consolidated thickness with 5.5% binder content by weight of total mix using paving bitumen VG 30 grade rolled and compacted to requied camber and gradient including preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bag to remove loose dirts etc. and applying evenly a tack coat with bituminous emulsion (RS-1 grade) confirming to IS-8887 at 3.00 Kgs/10 Sqm using emulsion pressure distributor on the prepared bituminous/ granular surfaces complete all as specified and as directed.

M&L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n.exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings not exc 15cm thickness (below or above GL) all as specified and as directed.

M&L 75mm thick PCC type D2, 1:4:8 (40mm graded aggregate) hard standing all as specified and as directed.

M&L for dismantling stone slabs and tiles laid dry and pointed of any description or thickness in floors, aprons etc all as specified and as directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer throughvibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M&L chequered cement concrete tiles 30cm x 30cm x 25mm thick, set jointed and pointed in neat cement slurry with grey cement and pigments over and including 20mm thick screed bed or bedding layer of mortar in cement mortar 1:6 for laying floor finishes all as specified and as directed.

M/L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and as directed.

Supply and fix in repair metal tubular delineator made out of ABS round body fitted with 2 Nos 65mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25mm wide stripes with anti theft net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1, complete all as specified and as directed.

Supply and fix in repairs cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufacturer's instructions, including dismantling of old complete all as specified and as directed.

S&F in repairs solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures insturctions etc., including dismantling old, all as specified and as directed.

S&F in repairs for 800mm dia road safety convex mirror, fixed with 50mm dia GI pipe light grade, standard length, out of that 450 mm minium length shall be embedded in PCC 1:3:6 type C1 (using 20mm graded stone aggregatyge) including excavation of pit of min size 300 x 300 x 450mm including dismantling complete all as specified and as directed.

M/S DIVIJA BUILDERS

B Sreepathy Rao & Sons