SPECIAL REPAIRS TO FLOORING, JOINERY, TOILETS, ELECTRIFICATION AND CONNECTED WORKS AT CHOLA HOUSE UNDER GE DSSC WELLINGTON

Amount

B/R Works Dismantling of single layer Mangalore pattern or similar tiles in roofing complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and as directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed

Taking down cement or cement lime plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position as in unframed work such as rafter, beam etc complete all as specified and as directed.

Dismantling wooden Battens for tiles, shingles etc, of any size including tilting fillets with spacing exc 15 cm complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for steel members of grill, rail etc complete all as specified and as directed.

Dismantling wall and ceiling board fibre pulp insulation etc or insulation boards/ slabs blankets any thickness, including cover fillets/ frame complete all as specified and as directed.

Taking down chowkats or frames with shutter (without taking off shutter from frame) not exceeding 1.5 sqm each including fittings complete all as specified and as directed.

Taking down chowkats or frames with shutter (without taking off shutter from frame) exceeding 1.5 sqm but not exceeding 4 sqm each including fittings complete all as specified and as directed.

Taking down shutters of any description exceeding 1 sqm and not exceeding 2 sqm each and refixing in the same opening complete all as specified and directed

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) (below or above ground level) and removing debris off the site complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided etc/roof padding concrete etc and removing debris off the site complete all as specified and as directed.

Dismantling boarding etc any description, fixed in any position with nails etc including iron/ SS mongeries if any complete all as specified and directed.

Demolition of cement concrete (reinforced) and removing debris off the site complete all as specified and as directed.

Material and labour for factory made UPVC Colour sliding windows with glazing all as per manufacturer's direction and following specifications :- (i) Window panel shall be 3 track frame with upvc profile section of size 112mmx 60mm having outer wall thickness of 2mm(+/- 0.3mm ) with sliding pattern with glazed and mesh shutter. (ii) window glass shutter for (front panel )shall be made of 66mmx 42.5mm having outer wall thickness of 2.0mm(+/- 0.3mm) . (iii) Window mesh shutter shall be made of 52mm x 22mm.Gauge shall be suitable wire gauge SS304 coated/fiber black mesh. (iv) All profile of frames and sash shall be reinforced with galvanised mild steel section of 1mm wall thickness at wherever required. (v) All the corners and joints of the frame shall be mitred cut & fusion welded without any mechanical joints. All welded joints are to be neatly trimmed & features grooved /raised nib finish so as to make the finished products free from all sharp edges & burrs. (vi) The lock shall be single point touch lock. All hardware like wheel, lock should be screwed .System shall be provided with suitable upVC beading size of 25mm x15.5mm for glazing of size 4mm/5mm pinhead /plain glass as directed by the Engineer In charge.

(vii) The profiles shall be cut to length and welded 45 degrees . (viii) The complete window shall be fixed into the prefinished opened place by drilling & fixing through the outer frame using high quality fasteners & silicon sealant is applied to fill up the gap between wall & window frame for leak proof installation and completion. Note: (i) The entire fixing will be done as per manufactures instructions and specification and as directed by Engg in charge. (ii) The unit rate quoted by contractor includes cost of glass/ wire netting and all other connected accessories. Net opening will be measured for payment purpose.

Supply and fix UPVC colour fixed series frame with following specification and all as directed. (i) Fixed series frame shall be of appropriate section of 60mm x 60mm with wall thickness 2mm ± 0.2mm conforming to IS 10151 of extruded UPC section . (iii)All the corners and joints of the frame shall be mitred cut & fusion welded without any mechanical joints. All welded joints are to be neatly trimmed & features grooved /raised nib finish so as to make the finished products free from all sharp edges & burrs. (iii)The profiles shall be cut to length and welded 45 degrees (iv) Glazing shall be provided with 5mm thick frosted glass fixed with appropriate size beading as per manufacture’s specifications. (v) All the fittings shall be provided with using self tapping screws. Note: The entire fixing shall be done as per manufacturer's instructions and specification and as directed by Engr-in-Charge. For UPVC frame and sash extruded profiles (+/-) 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. All as specified and directed .The unit rate quoted by contractor includes cost of glass and all other connected accessories.

Supply and fix UPVC panel door shutters with frames with approved make and section and colour with all necessary fixtures like hinges, handles, bolts etc all as specified and directed. The detailed specification as follows. (i) Door frame shall be upvc profile section of size of 60mm x 60mm wall thickness of 2mm(+/- 0.3mm ) with openable pattern.) (ii) Door shutter with sash made of 80mm x60mm and panel shall be 10 to15mm thick (+/- 0.3mm ) .All profile of frames and sash shall be reinforced with galvanised mild steel section of 1mm wall thickness at wherever required. (iii) All the corners and joints of the frame shall be mitred cut & fusion welded without any mechanical joints. All welded joints are to be neatly trimmed & features grooved /raised nib finish so as to make the finished products free from all sharp edges & burrs. (iv) The profiles shall be cut to length and welded 45 degrees

Supply and fix UPVC Mesh door shutters with frames with approved make and section and colour with all necessary fixtures like hinges, handles, bolts etc all as specified and directed. The detailed specification as follows. (i) Door frame shall be upvc profile section of size of 60mm x60mm wall thickness of 2mm(+/- 0.3mm ) with openable pattern.) (ii) Door shutter with sash made of 80mm x60mm) .All profile of frames and sash shall be reinforced with galvanised mild steel section of 1mm wall thickness at wherever required. (iii) All the corners and joints of the frame shall be mitred cut & fusion welded without any mechanical joints.All welded joints are to be neatly trimmed & features grooved /raised nib finish so as to make the finished products free from all sharp edges & burrs. (iv)The profiles shall be cut to length and welded 45 degrees (v) Gauge shall be suitable wire gauge SS304 coated/ fiber black mesh.

Supply and fix UPVC ventilator with The profile for construction of UPVC ventilator frame will be of overall size 60x58 mm with wall thickness 2.7 + or - 0.2 mm extruded sections. The corners will be plastic welded. The hinge side vertical outer frame shall be reinforced with galvanized channel of wall thickness 1.2 mm. The ventilator will be fixed to walls using 8 mm dia 80 mm dia MS screws minimum 2 no's on each side. The 3 nos of pinned glass will be placed in slots provided in ventilator and the ventilator will be glazed with 5 mm thick pinhead glass. Note: (i) The entire fixing will be done as per manufactures instructions and specification and as directed by Engg in charge. (ii) The unit rate quoted by contractor includes cost of glass/wire netting and all other connected accessories. Net opening will be measured for payment purpose.

M&L for providing gypsum board false ceiling 10-12mm thick fixed with standard GI frame work with GI fixing channels @ 1220mm c/c and inter spaced at 610mm c/c the main fixing channels shall be fixed through GI channels suspenders from roof @ 1200 c/c, main and inter connected channel shall be fixed through fasteners clips as per manufacturers instructions with and including plaster of paris decorative type cornice all around at the junction of wall and ceiling etc including applying two coats of oil bound distemper over one coat of approved primer complete all as specified and directed.

S&F 9/10mm thick PVC ceiling/ wall panels of interlocking types, width 250/255 mm with lamination design and exc 60% of PVC content including necessary H-joints, internal/external corner trim, corner cove,F/J edge trims where required fixed with hidden screws including aluminium frame work frame work complete all as specified and as directed.

Supply and fixing 0.60mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and as directed. .

Supply and fix Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/ on Chajjas, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed .

Supply and fix mild steel sections for joist, channel, angle or tee sections, post, etc fixed independently, without connecting plates, etc (cut to ordinary lengths i.e within 20mm of the length indicated) conforming to Fe 410-W (gde-E-250) quality-B etc complete all as specified and as directed.

Material and labour for 2nd class hard wood, clean sawn, as in scantling, purlins, rafters etc fixed to timber frame work complete all as specified and as directed.

M&L for roof tile, Mangalore pattern, interlocking at side joints, laid dry complete all as specified and as directed.

M&L for ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 complete all as specified and as directed.

Material and labour for cement concrete 1:4:8, type D-2 using 40mm graded aggregate as in foundation/ mass filling etc complete all as specified and as directed.

Material and labour for 25mm thick plain cement concrete 1:2:4 , type B-0, with using 12.5 mm graded stone aggregate as in floors for levelling course including finishing the surface complete all as specified and as directed.

Material and labour for Light shade coloured Vitrified Ceramic tiles 10mm thick (square/ rectangular) (double charged) polished, area of each tiles not exceeding 0.36 sqm, in floors, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 20mm thick screed bed in CM 1:4 complete all as specified and as directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded pointed in any mortar complete all as specified and as directed.

Material and labour for Dark shade coloured Vitrified Ceramic tiles (Double charged) 9 to 10 mm thick Matt finished, size of (1200mm x 600mm) as in floors etc. set and jointed cement slurry and pointed with epoxy joints with 3 to 4mm thick spacer over 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

All as per item No 34.00 above but set and jointed in neat cement slurry and pointed in coloured cement to match as in vertical surfaces such as skirting set in 10mm thick rendering in CM 1:4 complete all as specified and as directed.

Material and labour for light/dark shade (colour as approved by GE) Vitrified Ceramic tiles 9 to 10 mm thick size of each tiles of size (1200mm x 600mm) as in wall cladding, dado etc etc. set and jointed cement slurry and pointed with epoxy joints with 3 to 4mm thick spacer over 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Material and labour for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over 20mm thick Screed in cement mortar (1:4) including grinding and polishing complete all as specified and directed.

Material and labour for Granite work with 20mm thick machine cut, Jet Black granite slab in single piece or two piece length, table rubbed and polished, laid over and including 20mm thick cement screed in cement mortar 1:3, bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust and admixture of pigments to match with shade of granite stone as in cooking platforms, microwave platform, WHB counter top in steps, jambs, pillars, window-cills, etc, including cutting, polishing and rounding to edges of stone slabs etc., complete all as specified and as directed.

Supply and fix 2nd class hard wood wooden boarding 25mm thick as in floor with Planed one side & edges tongued and grooved or rebated, etc fitted with screws as in repairs to existing floors in patches, including cutting out, piecing, heading joints etc complete all as specified and as directed.

Supply and fix 2nd class hard wood plain solid, straight chowkhats and frames wrought, framed, rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

Supply and fix 35mm thick Ist class (First class) hardwood Plain, framed, panelled Moulded shutters(any number of panels), with rebated bolection moulded bead is provided and planted round the panels (for each side), wood particle board with commercial face veneers complete all as specified and as directed.

Supply and fix Ist class Hardwood Glazed and skeleton shutters,30mm thick open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkat complete all as specified and as directed.

Material and labour 4 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane including hacking out old broken glass (any thickness, size, quality or description) from wooden frame exe. 1.5 Sqm glazed with putty or fixed with beads complete all as specified and as directed.

Supply and fix Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Taking down steel tubing and connections of 15 mm bore including cleaning for refixing or removal to store complete all as specified and as directed.

Taking down steel tubing and connections of 20 mm bore including cleaning for refixing or removal to store complete all as specified and as directed.

Taking down Cast iron / PVC pipe 100mm jointed in cement mortar taking out of wall. including all fittings, heads, bends, swan-necks, etc complete all as specified and as directed.

Supplying and laying of CPVC pipes 20mm (outer dia) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

Supplying and laying of CPVC pipes 25mm (outer dia) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

Material and Labour for Dubbing out average 25mm thick on irregular face of walls of RRM /brick masonry surface in cement plaster 1:6 complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required & pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; & cutting chases for concealed water tubing or concealed conduit wiring, etc.& making good, cutting not exc 10 cm girth in brick wall complete all as specified and as directed.

Material and Labour for Reinforced Cement Concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and shelves etc complete as specified and as directed.

Material and Labour for use & waste of steel formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. to flat rough finished surfaces of concrete square or rectangle complete as specified and as directed.

Supply and fix TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete as specified and as directed.

Supply and fix TMT Mild steel bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete as specified and as directed.

Supply and fix 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches complete all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches complete all as specified and as directed.

Supply and fix PVC (SWR) bends any radius 110 mm bore provided with access door complete all as specified and as directed..

Supply and fix PVC (SWR) bends any radius 75mm bore provided with access door complete all as specified and as directed.

Supply and fix PVC (SWR) 110mm bore branch piece single (single Y) equal or Unequal complete all as specified and as directed.

Supply and fix PVC (SWR) 75 mm bore branch piece single(single Y) equal or Unequal complete all as specified and as directed.

Supply and fix PVC (SWR) vent cowl 110 mm bore complete all as specified and as directed.

Supply and fix PVC (SWR) vent cowl 75 mm bore complete all as specified and as directed.

Supply and fix in repair 75 mm dia PVC floor trap with cockroach trap and grating (double bowl type) with hole for waste pipe in grating including jointing to waste pipe complete all as specified and as directed.

Supply and fix in repair 75mm dia PVC floor multi trap with and grating of size 100 x 100 mm complete all as specified and as directed.

Supply and fix in repair 50 mm bore Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/sqcm in any length with rubber ring joint complete all as specified and as directed.

Supply and fix PVC connections 15mm size with brass nuts of length 600 mm each complete all as specified and as directed.

Material and labour for cutting holes in brick walls in mud mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, thickness exceeding half brick but not exceeding one brick, as required complete all as specified and as directed.

Material and labour for precast cement concrete block masonry with solid blocks made out of PCC 1:3:6, type C-1 with using 20mm graded stone aggregate, exceeding 10cm in width and setting in cement mortar 1:6 etc complete all as specified and as directed.

Material and labour for precast cement concrete type C-1(1:3:6) using 20mm graded stone aggregate solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar (1:4) complete, in walls ,partition, platform support etc complete all as specified and as directed.

Material and labour for Rendering in Cement Mortar 1:6, 15mm thick on fair face of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour Rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM (1:6) and 5mm thick in CM 1:4 finished even & fair (without using extra cement), mixed with water proofing compound complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately

Material and labour for complete removal of existing treatment on surfaces of ceiling and applying with white putty of 1.5mm thick and making the surface to an even and smooth finish by rubbing with sand paper of different grade etc and applying two coats of Oil bound distemper over a coat of primer by approved applicator of the manufacturer of the paint and all as specified and as approved for smooth finished surface of ceiling complete all as specified and as directed.

Material and labour for preparing new surface of steel and applying two coats of synthetic enamel paint over a coat of primer red oxide primer complete all as specified and as directed.

Material and labour Preparing newly plastered surfaces of external walls and applying one coat of exterior wall primer and two coats of Exterior Emulsion anti fungal weather proof paint complete all as specified and as directed. Note: The painting work to be executed by authorised applicator of the manufacturer. Make: APEX ULTIMA of Asian Paint or WEATHER COAT SMOOTH of Berger or Nerolac Excel Top guard of Nerolac or equivalent make mentioned in list of manufactures

Complete removal of existing treatment on external walls by wire brushing, crack filling & Bio-wash to fight microbial growth and applying, one coat of exterior wall primer and two coats of exterior emulsion anti fungal weather proof paint complete all as specified and as directed. Note: The painting work to be executed by authorised applicator of the manufacturer. Make:- APEX ULTIMA OF Asian Paint or WEATHER COAT SMOOTH of Berger or Nerolac Excel Top guard of Nerolac

Material and labour for applying wall care putty 1.5mm thick (Avg thickness) on new or old plastered surface of wall including finish the surface even and smooth with using appropriate sand paper complete all as specified and as directed.

Supply and fix Aluminium grill with a pitch of 52mmx 66mm fixed partition with appropriate aluminium frame/channel as per manufacturing and design including necessary drilling ,cutting, fabrication etc complete all as specified and directed.

Material and labour providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories like dome, etc complete all as specified and as directed.

Material and labour PCC (1:3:6) type B-0 (using 12.5mm graded stone aggregate) as in roof kerb, padding, coping, etc., including formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

Material and labour for cleaning the surface to remove all dust, dirt etc including Priming the surface with one coat of Smartcare Bituminous primer to enhance the bonding properties. Providing and laying of protective Geotextile fabric 45GSM over the bituminous primer application with proper overlaps. Supplying and applying single component, elastomeric,pitch modified PU coating with minimum elongation of 600% and tensile strength of 2 N/mm2 as per ASTM D412 and Shore A Hardness of 90 as per ASTM D 2240. The PU Coating shall have crack bridging ability of 2mm. The system consists of applying the water proofing treatment @ 1.2 Kg/ Sqm and shall havecrack bridging ability of 2mm etc complete as per manufacturer's instructions. Over the two coats of Flexi seal PU Waterproofing application, applying and sprinkling silica sand material to the roof area, etc complete as per manufacturer's technical specification and as directed . Note: The treatment should be carried out by the authorised applicator of the company

Material and labour for screed bed or bedding layer of mortar 20mm thick in Cement Mortar 1:4 mixed with liquid water proofing compound as per manufacturer's instructions on on fair faces of concrete surfaces over roof slab complete all as specified and as directed. Note: Liquid water proofing compound shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and as directed.

Supply and fix Butt hinges, 100mm long extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and as directed.

Supply and fix Door closer hydraulically regulated, (aluminium extruded section body) designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

Material and labour for Anti-termite treatment on voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

Material and labour for anti-termite at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

Material and labour for complete removal of existing painting surface from wooden surface including necessary plaining ,buffing etc to achieve plain smooth surface till the exposure of wood grain surface and applying two coat of melamine polish over one coat filler base coat and sealer base coat on wooden surface over 10cm girth or width complete all as specified and as directed..

Material and labour for preparation of new wooden surface including necessary plaining ,buffing etc to achieve plain smooth surface till the exposure of wood grain surface and applying two coat of melamine polish over one coat filler base coat and sealer base coat on wooden surface over 10cm girth or width complete all as specified and as directed.

Supply and fix Stainless steel soft close hinge with 35mm cup dia, full overlay, 110 degree opening suitable for 18mm thick shutters complete all as specified and as directed.

Supply and fix stain less steel handle of size 150mm for kitchen/ bedroom cupboards fixed with screws complete all as specified and directed.

Supply and fix Magnetic closer of suitable size for kitchen/ bedroom cupboards fixed with screws complete all as specified and directed.

Supply and fix stainless steel telescopic ball bearing channel, zinc plated finish for drawer including necessary fittings up to length of 600mm fixed with screws complete all as specified and directed.

Supply and fix coloured PVC toilet cabinet of size 622 x 422mm with looking mirror complete all as specified and directed.

Supply and fix in repairs stainless steel Double bowl kitchen sink under mount -flat edge gloss finish (40"Lx20"Wx8 "D) fitted with cement mortar/ chemical adhesive on granite/ marble back platform etc. including necessary fittings like waste coupling/ wastepipe etc complete all as specified and directed. Make :Parry ware cat No: C855981 or equivalent make in list of manufactures

Supply and fix stainless steel kitchen baskets (SS-304) of size 544mm x505mmx200mm complete all as specified and directed.

Supply and fix stainless steel kitchen baskets (SS-304) of size 544mm x505mmx100mm complete all as specified and directed.

Supply and fix stainless steel kitchen baskets (SS-304) of size 530mm x505mmx200mm complete all as specified and directed.

Supply and fix in repair Central hole basin mixer with out popup waste system with 450mm long braided hoses complete all as specified and directed. Make: Cat No - QQP-7169 BPM of Jaquar or G4715A1 of Parry ware or F730009 of Hindware or equivalent make in list of manufactures

Supply and fix in repair wall mixer 3-in-1 system with provision for both hand shower and OH shower complete with 115mm long bend pipe, connecting legs & Wall Flange (without hand & over head shower) complete all as specified and directed. Make: QQT-7281 of Jaquar or Cat No G4617A1 of Parryware or F730022 of Hindware or equivalent make in list of manufactures

Supply and fix in repair health faucet including 1.2m long flexible tube and wall hook complete all as specified and as directed Make: Cat No: ALD- 565 of Jaquar or E8342A1of Parryware or F160001 of Hindware or equivalent make in list of manufactures

Supply and fix in repairs Towel rail 600mm long complete all as specified and as directed. Make : Cat No : AQN-7711 of Jaquar or Prayag Cat No BA-01 or equivalent make in list of manufactures

S&F in repair over head shower 200 mm x 200mm including shower arm 20mm dia & 400 mm long round shape with 90 ° bend for wall mounted showers of with flange complete all as specified and as directed. Make: Cat No OHS-1619,SHA-455L400 of Jaquar or T9975A1,T-9802A1 of Parryware or F160142,F160024 of Hindware or equivalent make in list of manufactures

S&F in repair soap dish chromium plated complete all as specified and as directed. Make: Cat No:AQN 7731 of Jaguar or T6902A1 of Parryware or F580004 of Hindware or equivalent make in list of manufactures.

S&F in repair toilet paper holder with stainless steel flap fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed. Make: Cat No AQN-7753 of Jaquar /T6906A1 of Parryware/ F890003 of Hindware or equivalent make in list of manufactures.

Supply and fix in repairs stainless steel tubular towel rack 600mm long with lower hangers but with three hooks, Chromium plated , fixed on walls complete all as specified and as directed. Make: Cat No.AQN-7781 of Jaquar or T6008A1 of Parryware or equivalent make in list of manufacturer

Supply and fix in repairs corner glass shelf made out of glass with cp guard rail and wall fixing accessories of 300mm radius matt finished, chromium plated (MCH/Colour CP) with brass brackets fixed on walls complete all as specified and as directed . Make: Cat No.ACN-1173 of Jaquar or T6010A1 of Parryware or equivalent make in list of manufacturer

Supply and fix in repairs Angular stop cock 15mm bore, cast copper alloy, chromium plated, fancy type with wall flange conforming to IS screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and as directed. Make: Cat No.FLP QQP-7053PM of Jaquar or G3053A1 of Parryware or equivalent make in list of manufacturer

Supply and fix in repair hand shower 105mm round shape single flow (ABS body chromium plated with grey face plate) with rubit cleaning system including flexible tube 12mm dia 1.5 Mtr long with nuts complete all as specified and as directed. Make : Cat No.SHA-549D8/HSH-1717 of Jaquar or T-9902A1 of Parryware or F160055 of Hindware or equivalent make in list of manufacturer

Supply and fix in repair towel ring with round flange complete all as specified and as directed. Make: Cat No AQN-7721 of Jaquar or T6002A1 of Parryware or F580003 of Hindware or equivalent make in list of manufacturer

Supply and fix tumbler holder complete all as specified and as directed. Make: AQN 7741N of Jaquar or T6504A1 of Parryware or F880001 PGD of Hindware

Supply and fix Double coat hook including necessary fittings complete all as specified and as directed. Make : Cat No -AQN-7761 of Jaquar or equivalent in parryware/Hindware .

Supply and fix in repair glass shelve 55mm long including necessary fittings complete all as specified and as directed. Make : Cat No -AQN-7771 of Jaquar or equivalent make in list of manufacturer

Supply and fix CP bottle trap 32mm size with 250mm and 190mm long wall connection pipe including wall flange complete all as specified and as directed. Make : cat No : ALD -769L250x190 of Jaquar or equivalent make in list of manufacturer

Supply and fix in repair side single lever sink mixer with swinging spout on upper side (wall mounted model) with connecting legs and wall flanges complete all as specified and as directed. Make: Cat No FLP-5165PM of Jaquar or Cat No G3335A1 of Parryware or Cat No F320027 of Hindware or equivalent make in list of manufacturer

Supply and fix Vitreous china Wash Hand Basin, White, Table top l type of size 640x425x155mm . Cat No.JDS-WHT-25901 of Jaquar or equivalent of other specified makes of Hindware/Parryware, including 32mm waste coupling(click clack type) with full thread with 80mm height ,450mm long braided hose with M10x1 Nipple, 15mm nuts,O-ring & rubber washers and 32mm dia waste pipe 750mm long etc. including taking down existing one complete all as specified and as directed. Make: Cat No : ALD-727 of Jaquar or equivalent make in list of manufacturer

Supply and fix Vitreous china wash down water closet pan, Rimless bowl with cistern for coupled WC of size 385x650x800mm with UF soft close slim seat cover,hinges,dual flush cistern fitting with back filling and fixing accesories white coloured PVC seat cover, mild steel chromium plated or aluminised hinging device flushing cistern and P/S trap including connections to drain (or outgoing pipe) and taking down existing water closet etc., complete all as specified and as directed. Make : Cat No KUS-WHT-35753P180UFSMPMZ of Jaquar or equivalent make in list of manufacturer

Material and labour for Ist class hard wood (solid wood) for wall panelling of size 1200mmx150 mmx 20 mm thick prefinished including corner and edges fixed over with two coats of Touch wood polishing (PU Glossy finish) on wooden surfaces including preparing the surface, wooden filler over a coat of sealer over 12 mm thick plywood (BWP) adhesive/nailing fixed on wall all as per manufacturers instructions complete all as specified and directed.

Material and labour for hardwood for Cornices/ beading/ nosing/ moulding as used in pre-engineered wall panelling etc of cross sectional area n.exc 25 Sqcm complete all as specified and directed.

Material and labour for 12mm thick fibre cement boards with decorative cut design as directed by GE/ Engr In charge and fixed to wooden frame work with screws and applying two coat Synthetic enamel paint over on coat of appropriate primer base coat complete all as specified and directed.

Material and labour for preparation of new surfaces of walls and applying with white putty of average thickness 1.5mm and making the surface to an even and smooth finish by rubbing with appropriate sand paper of different grade etc and applying two coats of washable emulsion paint over a coat of primer by approved applicator of the manufacturer of the paint complete all as specified and directed.

Material and labour for complete removal of existing treatment on surfaces of wall and applying with white putty of average thickness 1.5mm and making the surface to an even and smooth finish by rubbing with appropriate sand paper of different grade etc and applying two coats of two coats of washable emulsion paint over a coat of primer by approved applicator of the manufacturer of the paint and all as specified and as approved

Supply and fix in repair 25 mm dia telescopic antique finish design curtain rod complete all as specified and directed.

Supply and fix in repair antique finish designer heavy duty stainless steel double curtain rod curtain brackets and end caps for door and window for 25mm dia curtain rod fixed to wall complete all as specified and directed.

Supply and fix in repairs double arm wall mounted reversible plain/magnifying pivital Mirror fixed with chromium plated brass screws on Tiled surface etc complete all as specified and directed . Make : Jaquar.Cat No : CAN-1185 or equivalent make in list of manufacturer

Supply and fix Aluminium door/floor seal with appropriate section of frame with rubber gasket including necessary drilling,bolting etc fixed with extedrnal doors complete all as specified and directed .

Supply and fix Brass Mortice lock (six lever levers) 200mm long with cover plate and handle(5") complete for Left/Right handed door complete all as specified and directed .

Supply and fix 200mm long Antique finish tower bolt with ss rod complete all as specified and directed .

Supply and fix Antique finish (Zinc alloy) lotus style 350mm long door handle complete all as specified and directed .

Supply and fix Antique finish (Zinc alloy) lotus style 200mm long door handle complete complete all as specified and directed .

Supply and fix Rectangular wall mounted Backlit LED mirror of size 600mm x450mm with touch sensor (warm white,natural & day light) complete all as specified and directed .

Supply and fix Stain less steel Flip-up grab bar 430mm long (17 inch) with anti-slip nylon grip (white or coloured) complete fix to the tiled wall surface with chromium plated screws complete all as specified and directed .

Supply and fix 304-Grade stain less steel matte finish floor trap (Floor drain) of size (12x 4 inches) including built in cockroach trap,stainer and drain cover complete all as specified and directed .

Supply and fix 304-Grade stain less steel cockroach trap (Floor drain) of size (5x 5 inches) including built in cockroach trap,stainer and drain cover complete all as specified and directed .

Material and labour for bituminous shingles with mineral and synthetic reinforcement comply to BSEN 544 with seepage & slope stability roofing shingles (two piece laminated shingles) thickness 4 to 6mm on concrete surface as in roof,chajja etc complete all as specified and directed .

Material and labour for bituminous shingles starter strip with mineral and synthetic reinforcement comply to BSEN 544 with seepage & slop stability roofing shingles (two piece laminated shingles) thickness 4 to 6mm on surface of roof,chajja etc complete all as specified and directed .

M&L Complete removal existing surface finishes and applying texture putty 3-5 mm thckness and applying texture design as approved by GE and applying two coats of plastic emulsion over a coat of primer complete all as specifed and directed.

M&L for elevation tiles of size 600 mm x 300 mm x 8 to 9 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match as in vertical surfaces of dado/skirting/cladding set in 10mm thick CM 1:3 complete all as specified and directed.

Supply and fix in repair two concealed stope cocks with basin spout (composite One piece body) complete all as specified and directed. Make: Jaquar Cat No : ARC-87433 equivalent make in list of manufacturer

Supply and install Wall enclosure with two fixed glass up to ceiling height and openable door in between.Door is up to the standard height .One fixed glass panel on the top doo to cover the gap above the door. The entire glass panel shall be of 10mm frosted or pin headed type. Width of the enclosure shall be 2001 mm to 2400mm and height shall be of 2300mm. Make : Jaquar Cat No: JSS-CHR-830S2024H23X or equivalent make in list of manufactures Note : The rate shall be included all fittings like Glass hinges, Glass conector,floor clamp,stabilizer rod and roller etc all as per manufacture instruction

Taking down carefully the existing glass partion (shower enclosure) of any size and height from the bath room and refixing the same after the tiling, repair work etc including necessary drilling,silicon gel etc all as directed by the Engr In Charge.

E/M Works Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc., removing materials out side MD land in case of Credit and making good disturbed surfaces of walls, floors, etc., all as specified and as directed.

Disconnecting/ dismantling of old existing unserviceable DB's any way 240/ 415 volts with their old/ unserviceable MCBs complete all as specified and as directed.

All as per item No. 145.00 above but for One light / fan point / call bell controlled by one, one way switch complete all as specified and as directed

All as per item No. 145.00 above but for One 3 pin 6/ 5 Amps socket outlet point on independent board complete all as specified and as directed

M&L for point wiring complete all all as specified with 1100 Volts grade 2.5 sqmm single core PVC insulated FRLS 1000 Volts grade with multi stranded copper conductor confirming to IS 694 1990 with ISI marked (for phase, netural and earth ) in and including stove enamelled steel conduit with ISI mark of minimum 20 mm ia and all accessories concealed including / cutting / chases in wall / ceiling / fixed to roof / truss/ columns etc and including factory made branded make embossed glvanised steel pressed terminal boxes alongwith suitable size modular cover plates with frames for fixing modular switches and sockets , fan regulators etc. of suitable size and the earth wire to connected to common earth dolly complete all as specified and directed for one three pin modular switch socket 16 Amps outlet on independent board.

Supply and fix Modular switch 1 way 6A, 1 module, 230V, AC, 50Hz, single pole ISI marked complete all as specified and as directed.

Supply and fix Modular socket, shuttered 6A - 2/3 pin combined 2 module, ISI marked complete all as specified and as directed.

Supply and fix Modular switch 1 way 16A, 1 module, 230V, AC, 50Hz, single pole ISI marked complete all as specified and as directed.

Supply and fix Modular shuttered socket outlet, 6A/16A - 2/3 pin combined 2 module, ISI marked complete all as specified and as directed. .

Supply and fix Modular Bell push 6A, 1 module, 230V, AC, 50Hz, one way ISI marked complete all as specified and as directed.

Supply and fix Ceiling rose, surface backlit type three terminal 65x50mm, ISI marked complete all as specified and as directed.

Supply and Fixing Buzzer Dingdong AC, 230 Volt single pole complete all as specified and as directed.

Supply and fix TV coaxial socket, 1 module complete all as specified and as directed. Make: Cat No.-ACVKTOW001 of Crabtree or equivalent make in list of manufcatures

Supply and fix internet socket RJ-45, suitable for CAT 6 cable, shielded, folded metal 1 module complete all as specified and as directed. Make: Cat. No. ACVKJWW451 of Crabtree or equivalent make in list of manufcatures

Supply and fix in repair LED street light /security light luminaries fitting 1X35 watt LED including GI bracket made out of GI pipe light grade 25 mm dia 1.20 m long bent to shape with suitable size mild steel clamps of size 50 X 6mm with nut, bolt, & washers as required at site for fixing of street light on LT poles / wall including making connection with PVC insulated 3 single core of 1.5 sqmm size multistranded copper conductor cable complete all as specified and directed.

Supply and fix in repair decorative bulk head edge lit LED luminaire 10W with min 120 lumens/watt output IP >= 65,IK>=07, Class I Environment friendly, energy saving, surface mounted, made of pressure die cast aluminium housing with suitable fixing arrangement complete with all accessories internally prewired and including connecting up with and including three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC , (4 ft.) High performance electronic driver , operating temperature 10 C to 35 °C operating voltage range 140 V -270 V , Average life 50000 hours and LED lamp including High efficiency long life LED with lumen efficacy of 140 Im/watts and ABS end caps tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make: Havells cat part No ENDURA LINEAR NEO BS 20W LED 865SPCSS or equivalent make in list of manufcatures

Supply and fixing LED lights fitting 1x 20W, 220V, AC , (2 ft.) High performance electronic driver , operating temperature 10 C to 35 °C operating voltage range 140 V -270 V , Average life 50000 hours and LED lamp including High efficiency long life LED with lumen efficacy of 140 Im/watts and ABS end caps tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make: Havells cat part No ENDURA LINEAR NEO BS 10W LED 865SPCSS or equivalent make in list of manufcatures

Supply and fix in repair round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with twin core flexible copper conductor cable of suitable size complete all as specified and directed.

All as per item No. 162.00 above but 15 W complete all as specified and directed.

All as per item No. 162.00 above but 18 W complete all as specified and directed.

Supply and fix in repair Surface mounted 18 watt 220 volts AC , pressure die - cast aluminium luminaire in powder coated white finish in Square profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver complete with drivers, suitable for roof ceiling including connecting up with twin core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix in repair decorative wall mounting fitting with suitable for two LED lamp , B22 holder type, double arm type Brushed nickel finishing fixture luminaire of double arm with Opal glass diffuser with all accessories internally prewired and including connecting up complete all as specified and as directed. Make: Havells Cat No. FLORETNE WL 2 LS B22 SS or equivalent make in list of manufactures

Supply and fix in repair decorative wall mounting fitting with suitable for one LED lamp , B22 holder type,single arm type Brushed nickel finishing fixture luminaire of double arm with Opal glass diffuser with all accessories internally prewired and including connecting up complete all as specified and as directed. Make: Havells Cat No. FLORETNE WL 1LS B22 SS equivalent make in list of manufactures

Supply and fix in repair wall mounting decorative display light of rating 15W, 6500K warm white with aluminium die cast body and PC diffuser with all fixing arrangement for fixing above table and pictured complete all as specified and as directed. Make: Havells, Cat No : UNECOSNOOTDLR15WLED830S36 or Luker Cat part No LODARCS -3 D or equivalent make in list of manufactures

Supply and fix Distribution Board ( Vertical Load line DB) double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 08 way, 240 volts with copper bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB as incomer and MCB as outgoing and making all necessary connection complete all as specified and as directed.

Supply and fix MCCB, 4 pole, 63 A rating (Ics=100% of Icu),415Volts,16 kA Breaking capacity with adjustable overload & adjustable Short circuit setting thermal magnetic release complete all as specified & as directed.

Supply and fix Miniature circuit Breakers, TP of capacity 25-63 Amps,C-Series 415 Volts with breaking capacity 10 kA complete all as specified and as directed.

Supply and fix Miniature circuit Breakers, TPN of capacity 16-32 Amps,C-Series 415 Volts with breaking capacity 10 kA complete all as specified and as directed.

Supply and fix SPN DB, 12 Way, IP43, IK09, Metal double door type 240 volts fitted with bus bar and blanking plates, neutral link and making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed.

Supply and fix SPN DB, 8 Way, IP43, IK09, Metal double door type 240 volts fitted with bus bar and blanking plates, neutral link and making good the disturbed surfaces with all other accessories including necessary connection complete all as specified and as directed.

Supply and fix Miniature circuit Breakers, SPN,of capacity 32 Amps C-Series 240 Volts with breaking capacity 10 KA complete all as specified and as directed.

Supply and fix Miniature circuit Breakers,capacity (6-32 Amps) single pole,C-Series 240 Volts as ordered with breaking capacity 10 KA complete all as specified and as directed.

Supply and Fixing exhaust fan PVC 150 mm sweep and connecting up including cleaning and painting with white enamel paint one coat and provision of cable from ceiling rose/connector to fan complete all as specified and directed. Make Cat part No. Ventil Air DS of Havells or equivalent make in list of manufactures

Supply and Fixing exhaust fan metal body 300 mm sweep and connecting up including cleaning and painting with white enamel paint one coat and provision of cable from ceiling rose/connector to fan complete all as specified and directed.

Supply and fix rigid non-metallic PVC conduits of external dia 25 mm exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends with aluminium clamp, bolt, nuts etc for fixing complete all as specified and directed.

Taking out/ down the existing energy meters, cleaning and deposit to BSO in good condintion and stickering the name of the corresponding Qtr No complete all as directed by Engr-in-Charge.

Labour only for refixing the serviceable existing energy meters, cleaned and collected from BSO in good condintion as fixing the stickering Qtr No complete all as directed by Engr-in-Charge.

Material and labour for Earthing with galvanized steel earth plate 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate n.less than 1.5 m below normal ground level, connected to galvanized iron wire 4 mm as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints as shown in drgs and including excavation and earth work, GI pipe light grade 25mm bore of protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:2:4) type B-1 Chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia , PGI funnel and wire mesh , 20 mm dia GI Pipe light grade for watering, Cast Iron frame with hinged pit cover of size 12"x12" having 7 kg weight complete all as shown in drg and connected to earth test point including testing complete all as specified and directed. Note : The length of the GI wire beyond 7.5 mtr will be measured and paid separately.

Material and labour for Coaxial TV cable, RG-6 with less signal losses including necessary items complete all as specified and directed

Taking down the existing Jumer Light fitting decorative type including connecting items and electrical connection and refixing the same complete all as specified and directed .

Supply and fixing auto cleaning, filterless ,electric Chimney of 90 cm hood, T- shaped, digital display, slant body and 200 W power with high quality heat resistant tempered glass of 1500 cubic meter per hour turbo suction power , made of stainless steel material and along with almunium duct pipe for exhaust purpose including provision of exhaust duct holes of suitable size in existing wall complete all as specified and directed. Note : Neceessary electrical supply items will be measured and paid separately.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 50 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc complete all as specified and directed . Make : Cat part No GHEBMKSWH050 of Havells or equivalent make in list of manufactures

N SARAVANAN (BID ID -3505665)

sree devi construction (BID ID -3505397)

shree jayam enterprises (BID ID -3505435)

KRA Engineering and Construction (BID ID -3505638)

VVM CONSTRUCTIONS (BID ID -3505759)

S.RAMACHANDRAN (BID ID -3505652)

GUNASEKARAN AND CO (BID ID -3505718)