PROVN OF UNDER GROUND CABLE FOR CONNECTION OF SECURITY LIGHTS INSIDE THE PERIMETER WITH BACKUP GENR SET AT FASF, INF DIV AND SPL REPAIR/REPLACEMENT OF OLD UNSV OVER HEAD LINE INTO UNDER GROUND CABLE LT PANEL, PCC POLE AND ALLIED WORK AT RVC E AND

Amount

Supply,fixing,installation and testing LT pannel out door (kiosk type) type,wheather &vermin proof MS sheet housing 3.15mm thick, double door front & rear openable type mounted on 50x50x6 mm angle iron frame,floor mounted type with coloured horizontal Tinned aluminium bus bar 4 pole mounted on insulators of rating 400 Amps, One ON LOAD changeover switch, 4P, 200A, = 01 Nos,36 KA 415 volts at incoming supply.the panel size not less than 900x800x500 mm with cable gland ,duly powder coated,locking arrengement complete and including grouting in PCC block of suitable size and Digital street light timing switch having lighting control (ON-OFF) through digital 24 Hrs and pre wired with suitable size copper conductor single core pvc sheathed cable all mechanism all as directed by Engr -in Charge.

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 Mtr deep below ground level) with top edge of plate not less than 1.5 m below normal ground level connected to galvanized iron strip of 32 x 6 mm earth lead by means of bolts nuts, check nuts and washers of galvanized iron steel and connected to angel board as directed and including necessary excavation in any type of soil and earth work disposal of surplus soil and provision of concrete pit in PCC (1:3:6) type C-1 pre cast RCC (1:2:4) cover slab of size 54 cm x 54 cm x 50 mm thick with one handle for lifting made out of 8 mm dia MS bar and MS 8 mm dia Tor bars 10 cm c/c both ways as in reinforcement, funnel, wire mesh, 40 mm bore GI pipe medium grade for watering and earth strip protection, charcoal and salt in alternate layers, complete all as shown on electrical plate No 3 of MES schedule Part - I (2009).

Supply and Laying XLPE UG cable PVC insulated,bedded armoured heavy duty electric cable 1100 volts grade with aluminium conductor of size 70 Sqmm 3.5 core in trenches or fixed on wall/floor/ pole complete all as spd and directed.

Supply and Laying XLPE LT UG cable PVC insulated,bedded armoured heavy duty electric cable 1100 volts grade with aluminum conductor of 25 Sqmm 4 core in trenches or fixed on wall/floor/poles complete all as specified and directed.

Excavation in trenches in soft/loose soil n.exc 1.5m wide and n. exc 1.5m depth for laying of cable, errection of poles, stay and pipe line,and getting out complete all as specified and directed

Returning & filling in including spreading, leveling watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified.

Removal of excavated surplus soil to a distance n. exc 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L for fly ash old size bricks , straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection all as specified.

M & L for local sand coushioning with dry and clean over and under the cable for protection of cable , 80 mm sand laid before laying the cable 150 mm sand after laying the cable and filling the sand in cable duct of inside the sub station building complete all as specified and directed. Note:- Punned thickness of sand shall be measured for payment.

Supply, installing, testing and commissioning of LT out door type factory made(CPRI Approved ), junction box of size 750mmX600mmX500mm (over all dimension )with mild steel angle iron of size 50X50X6mm vertical frame and legs with mild steel Angel iron 50x50X6 mm in horizontal sides of the frame LT Junction box (KIOSK), outdoor type, platform mounted, suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system,The panel shall be dust and vermin proof, IP 65 class protection and made of 3.15mm CRCA MS sheet and 50x50x6 mm thick angle iron frame work, powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front & back opening type, with aprons for cable entry, and fixing danger notice plate made of 1.6mm thick mild steel sheet, vitreous enameled white, of size 20 x 15cm with letter, figures and conventional skull bones in signal red colour and fixed front & back door pillar box etc with voltage and danger indicated in Hindi and English complete all as specified and directed.with double door shutter and locking arrangement . Aluminium bus bar (LxWxH) 400 x 10x50 mm with drilled holes for incoming /out going cable core connection including aluminium lugs ,GI bolts ,Nuts and washers of suitable size . Porcelain / synthetic bridge insulators, heavy duty with necessary steel / GI screws ,bolts, nuts and washers -08 Nos , the platform shall be such that it is of a height 45 cm above the nearest road level including connections of all out going/in coming existing cables of size 25 to 300 sqmm by drawing /digging out cable from loops in trenches out side the Bldg inclusive of necessary excavation and earth work as required and relaying the cables with retrieved bricks and providing new sand cushioning and crimping suitable size lugs for terminal connections of cables, necessary brick foundation with plastering complete all as specified and as directed by Engr-in-Charge (NOTE:-LT Panel board should be as per IS/ICE 61439-part I&II Type Test certificates and Panel Builder should submit all Certificates before executing the job.)

Supply, installing, testing and commissioning, factory made and tested , LT Panel (KIOSK), outdoor type, minium size 900 x 900x 600mm and platform mounted, suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, having bus bar chamber with insulated aluminum bus bars 400 Amps rating installed on porcelain insulators. The panel shall be dust and vermin proof, IP 65 class protection and SMC/made of 3.15mm CRCA MS sheet and 40x40x4mm thick angle iron frame work, powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front opening type, with aprons for cable entry, with double door shutter and locking arrangement , internal wiring with PVC insulated, stranded copper conductor, FRLS cables, IS-694 marked of adequate size but not less than 2.5 Sqmm. The platform shall be such that it is of a height 45 cm above the nearest road level. complete all as specified and directed including connections of all out going/in coming existing cables of size 25 to 240 sqmm by drawing /digging out cable from loops in trenches out side the Bldg including of necessary excavation and earth work as required and relaying the cables with retrieved bricks and providing new sand cushioning and crimping suitable size lugs for terminal connections of cables, necessary brick foundation with plastering to the Panel board, All out going feeders shall be connected and The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint and and fixing danger notice plate made of 1.6mm thick mild steel sheet, vitreous enameled white, of size 20 x 15cm with letter, figures and conventional skull bones in signal red colour and fixed front & back door pillar box etc with voltage and danger indiated in Hindi and English complete all as specified and as directed by Engr-in-Charge , The scope of work includes the following: (NOTE:-LT Panel board should be as per IS/ICE 61439-part I&II Type Test certificates and Panel Builder should submit all Certificates before executing the job.)

(I) Incoming :-

(i) MCCB 4 Pole, Thermal Magnetic Based 250 A, Breaking capacity 16 KA, 415 V, 50 Hz with OL, SC, EF protection, -01 No along with Spreader terminals.

(ii) Indicator lamp LED type (R, Y, B) complete with fuse -01 Set

(II) Outgoing :-

(i) MCCB 4 Pole, Thermal Magnetic Based 160 A, Breaking capacity 16 KA, 415 V, 50 Hz with OL, SC, EF protection, -01 No along with Spreader terminals

(i) MCCB 4 Pole, Thermal Magnetic Based 100 A, Breaking capacity 16 KA, 415 V, 50 Hz with OL, SC, EF protection, -01No along with Spreader terminals

(ii) MCB TPN 63 Amp C-Curve - 2 No

M&L for plate earthing for sub station equipments complete with galvanised mild steel plate electrode 60 cm x 60 cm x 6.3 mm thick buried directly in ground vertically (in earth pit not less than 3.5 m below normal ground level) with the top edge of the earth plate at a depth not less than 2.75 m below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and incl GI earth strip 32 x 6 mm bolted (with GI nuts, bolts & check nuts) and riveted to earth plate at one end and connected to metallic bodies of HT/LT equipments etc at the other, earth strip encased in and including 40mm bore GI light grade pipe with all fittings from top of electrode to body of equipment fixed with and including 25 x 3mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from bottom of earth pit to top of electrode complete with earth pit in PCC 1:2:4 type B-O using 12 mm graded crushed stone aggregate excavation & earth work and RCC cover complete all specified and shown in electrical plate No 5 of SSR Pt-I.

Supply, laying, jointing, testing and commissioning LT underground cables, 1100 volts grade, XLPE insulated and PVC sheathed, heavy duty armoured, with multistranded aluminium conductors, IS-7098 (marked, laid in trenches / ducts / fixed on poles / walls / laid under roads / paths / drain / culverts or encased in GI pipe and removing unsv any size cable complete all as specified and directed. Cables of the following sizes:-(Note;- Rate quotted includes terminal Lugs / road cutting/ wall cutting/ floor cutting and making good damged portion matching with existing surface with all existing finishes.)

16 Sqmm 4core

50 Sqmm 4 core

70 Sqmm 3.5 core

95 Sqmm 3.5 core

120 Sqmm 3.5 core

240 Sqmm 3.5 core

Taking down LT U/G cable any size upto 50 sqmm complete all as specified & directed.

Relaying, jointing, testing and commissioning LT underground cables any type and size (marked, laid in trenches / ducts / fixed on poles / walls / laid under roads / paths / drain / culverts or encased in GI pipe complete all as specified and directed. Note:- (a) Rate quotted includes terminal Lugs / road cutting/ wall cutting/ floor cutting and making good damged portion matching with existing surface with all existing finishes.) Note :-(b) Excavation & earthwork, duct work, GI pipe for laying of cable and sand cushioning / cable protection covers etc are beyond the scope of this item and shall be measured & paid for separately under respective items of Sch `A'.

Excavation in trenches not exceeding 1.5 m wide and exceeding 1.5 m in depth and getting out in Soft/Loose soil including trimming sides and bottom of trenches complete all as specified & directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in Soft/Loose soil including trimming sides and bottom of trenches complete all as specified in the following type of soils:

Returning, filling-in, including spreading, watering and well ramming in layers not exceeding 25 cm thick each, in soft /loose soil complete all as specified in the following type of soils

Removing excavated surplus soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

Material and labour for river washed and screened, dry sand for filling in trenches below and around underground cables for cushioning of cables complete all as specified.

M & L for Bricks for protection cover to under ground cable (with standard size fly ash bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10mm as directed.

Supply and laying galvanised steel water tubing, light grade, IS-1239 marked with all fittings (IS marked) and laid in trenches / under roads / in drains / fixed to poles/walls ( with required size flat iron clamp bolts, nuts and washers ) pipes of the following sizes :-

50 mm bore

80 mm bore

100 mm bore

M&L for auguring of hole suitable for passing 40mm to 100mm bore pipe in true horizontal position under road, PCC paths etc., by means of mechanical ring/ auger after doing ultrasound to prevent any damage to existing cables pipe line specified and directed coming in the route not exceeding 1.5 m in depth below existing surface level of road and not excd 30M in length complete all as specified. Note: Pipe shall be measured and paid separately under appropriate items and any dahage to existing cables of anytype shall be made good by the Bidder without any extra cost to department.

Cutting of worn-out / burnt aluminium cable terminal lugs from the HT/LT cable , crimping of new aluminium cable core and fixing with transformer/ Panel MCCB terminal/ FPB/ JB/ pole/DBs/ stud including cutting/ dressing of cable, disconnecting under ground / OH line cable conductor , cutting down worn-out portion and refixing with suitable lugs complete , including under ground cables of any type and size for repairs including taking out underground cable loop from ground and making connections of restoration of electric supply complete all as specified and directed Engr-in-Charge . Note:- (Excavation, earth work , taking out cable protection covers, and sand cushion and relaying the same shall be deemed included in the unit rate quoted by Contractor)

S&F service main distribution (SMC JUNCTION BOX ) box minimum inside size 395 x 235 x 150 mm with Bus bar 200 amps 4 pole for distribution of multiple nos of service connection, (ISI marked )weather and moisture-proof, nuts and bolted bus bar system, 200 Amps capacity and fixing on pole/wall with suitable FI clamp nuts and bolt complete all as specified and directed.

S&F pole mounting type junction box factory made of minimum in side size of 300x200x100mm of FRP sheet duly powder coated with front openable hinged door , locking arrangements, with 4 Nos aluminium bus bars 40 Amps rating mounted on porcelain insulator, cable glands and lugs consisting DIN type rails for fixing MCB DP 6/10 Amps, 10 kA suitable for domestic loading , -01 no. including mild steel flat iron clamp made out of 40x4mm FI, nuts, bolts and washers duly painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed Engr in Charge.

Supply & fixing Unplasticised PVC pipes of prssure rating 10Kgf/Sqcm 15 mm bore and 3mm thick complete fixed on pole using suitable clamps nuts & bolts (not less than 03 Nos) complete all as specified and as directed

Supply and fixing three core 1.5 Sqmm x3 core (nominal area) Confirming to FRLS cables, IS-694 ,PVC insulated and PVC sheathed multi stranded unarmed copper conductor cable LT 1100 volt grade including removed unsv any type cable complete all as specified and as directed by Engr in charge.

Supplying, transporting to site, erecting, and fixing in position, steel tubular swaged and welded poles of Overall height 9 metres, type 410 SP-31, IS-2713 marked, with mild steel base plate (fillet welded to poles), pole cap / finial taper plug, bolts, nuts, washers etc, including painting on the outside with two coats of aluminium paint over a coat of red oxide primer on exposed surfaces and black bituminous paint on steel surface embeded in concrete and painting 03 nos band /strips with fluorescent , PO box red synthetic enamel paint ( 30 cm wide each) at a distance of 30 cm from plinth block and numbering of poles including taking down old U/S PCC polecomplete all as specified and directed by Engr-in-Charge.(Note:- Poles shall be swaged and welded at manufacturer’s factory and not at site. The inner surface shall be factory painted)

M&L for PCC (1:4:8)type D2 using 40 mm graded stone aggregate infoundation(below pole) complete all as specified and as directed.

M&L for cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate for foundation of pole . (around the poles in pit) complete all as specified and as directed

M&L for PCC (1:3:6) type C-1 using 20mm graded stone aggregate for coping / pedestal of poles including necessary form work, fair finishing to exposed surfaces using extra cement complete all as specified and as directed

Supplying and fixing street light timing switch having lighting control (ON-OFF) through Astronomical Calculation of Sun rise/ sun set by setting date, time and degree of longitude and latitude without separate light sensors and prewired with suitable size of copper conductor single core PVC insulated and sheathed cable and all mechanism fitted into panel, outdoor type , pole mounted with FI 25x4mm clamps , nuts, bolts and washers dully painted, connecting and testing factory made , epoxy powder coated, Single Phase street light panel, digital 24 hrs, suitable for 6KW (max) complete with 63 Amps TP Contactor, and 63 Amps TPN MCBs and fixed on pole/ wall/ feeder pillar complete all as specified and directed by Engr in Charge

Dismantling old existing ACSR conductor of any type/size.

Dismantling old existing MS cross arms of any type/shape.

Dismantling old existing Insulators of any type/shape.

Dismantling old existing LT stay assembly complete all as specified and as directed

SIYA ASSOCIATES (BID ID -3039659)

AUTOMATION AND SWITCHGEAR PANELS (BID ID -3050056)

Shikha Enterprises (BID ID -3042442)

PARADISE INFRA POWER COMPANY (BID ID -3042180)

EX SOLDIERS MECHANICAL WORKS (BID ID -3041586)

KUKREJA BROTHERS (BID ID -3041650)