Virudunagar Museum

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Pre-Construction anti-termite treatment plinth area – surface treatment stage-1 :- Completion of earth work for column footings before laying plain cement concrete 25mm dia Hole spaced at 30cm center to center on both direction will be made at the bottom of earth workand the chemical will be poured in the holes and will be sprayed in the four sides of earth work at the rate of 3 litres of chemical solution (Chlorophyrifos emulsion diluted in ration 1:19 (One emulsion and 19 water ) per square metre payment shall be made after completion of 3 stages. stage-II :- After filling the basement before laying flooring concrete with filling crushed stone sand (M Sand) 25mm dia holes to adepth of 450mm will be made inside the basement and the chemical will be poured in the holes at the rate of 3 litres of chemical solution (Chlorophyrifos emulsion diluted in ration 1:19 (One emulsion and 19 water ) per square metre payment shall be made after completion of 3 stages.

Peripheral treatment stage-III.On completion of building and leveling the outer area adjacent to the walls column ground ponds of size (900X300 mm will be filled in the ponds at the rate of 3 litre of chemical solution per Rm payment shall be made after completion of 3 stages. Stage-IV.Spraying termite solution around the building (Out side of the building) by making crowbar holes around the building before laying the plinth protection. This holes has to be closed after the treatment

Supplying and filling of gravel by lorry in basement filling in Layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers..

Supplying and filling with clean Crushed Stone Sand (M.Sand) in Layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers..

Plain Cement Concrete 1:4:8(One Cement, Four Crushed Stone Sand (M.Sand) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever found necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Damp proof course with Cement Mortar 1:4 (One Cement and Four Crushed Stone Sand (M.Sand)) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used and finishing, curing etc. complete complying with standard specification.

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg of Crushed Stone Sand (M.Sand),

but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Upto Basement

In Ground floor

In First floor

In Second floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and GI binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton.(Payment for centering shall be given after the concrete is laid)

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.complete complying with standard specifiction.

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.complete complying with standard specifiction.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Brickwork in cement mortar 1:5(One cement, Five Crushed Stone Sand (M.Sand)) using II Class Ground Moulded Chamber Burnt Brick of size 9" x 43/8" x 23/4" including curing,etc., complete complying with standard specification

In Basement

In Ground floor

In First floor

In Second floor

Brick partition walls of 11.50cm thickness using best quality II Class Ground Moulded Chamber Burnt Brick of size 9" x 43/8" x 23/4" in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

In First floor

Providing and Fixing the Wooden Column Post With Wooden Capital on top of the column and Granite Stone Pedestal place at below the column, The rate inclusive of all materials, labour power and conveyance of materials to the work site, loading & unloading etc., and as per drawing and design by the Departmetnal Officers and All the materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

GF Column 200 X 200

FF Columns 150 x 150

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Crushed Stone Sand (P.Sand)) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five Crushed Stone Sand (P.Sand)), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed Plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and fixing MS Grill for Doors windows and ventilators etc. using MS angles, flats of approved quality conforming to IS specification with ornamental design as directed by the departmental officers. The rate is inclusive of cost of MS angles, flats, rods, transporation charges, labour charges for cutting, fabrication, welding including drilling holes, finishing assembling at site, fixing in position, including dismantling the masonry, making necessary holes in masonry/RCC works wherever necessary to the extent required and redoing the same to the original condition after fixing including one coat of red oxide primer etc. complete.

Supply and fixing II class Teak wood for frames 100x75mm size of door including all material and labour charges for teak wood wrought and put up in position and the size and section as per the architural drawings & Specification

Teak Wood Scantlings 2m in length

Teak Wood Scantlings 2m to 3m in length

Supply and fixing T.W panelled door shutter with ornamental design of required size using 150mmx40mm scantlings for style and bottom,middle rails,230mmx50mm scantlings for top rail and 25mm thick planks for panelling. The rate is including polishing with melamine polish , supply and fixing furniture fittings such as 150mmx25mmBrass hinges-3 nos,200mmx12mm Brass tower bolt -2 nos,Brass door stopper-1 no and Brass ornamental handles for inner and front etc., as directed by the architect complying with standard specification.

Supplying and fixing Teak Wood Framed Glazed Window / Door Shutters of 50 mm thickness including all materials and labour for wrought and put up in position and brass furniture fittings such as 4'' hookreye 4'' hinges and 600 mm length traditional Tower bolts and brass handles with necessary scrows etc.., Complete as per drawings

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Polishing the teak wood door with two coats of best melamine polish with approved quality and brand over a coat of bee's waxing including preparing the wooden surface to receive polishing, etc., complete complying as per the standard specifications. (The make, quality and colour of french polish, bees vax should be got approved by the Executive Engineer before use on works.)

Supplying and fixing teak wood handrails for courtyards terraces, and ramps using 50mm X100mm rail and main supports size at a height of 1000mm and 900mm from floor level with 50mm X 50mm thick teak wood as balusters joint to bottom and top rail including cutting, fixing charges and applying Lac polish as the finish to the rail as directed by the departmental officers

Paving the floor with best quality Heritage pattern Cement tile of bharat tiles brand of size 200 x 200 mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three Crushed Stone Sand (M.Sand)) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The design of the tiles should be got approved by the Architect before use on works)

Finishing the top of slopped roof, sun-shade with Mangalore Tiles of approved quality laid in cement mortar 1:3 (one cement and three Crushed Stone Sand (M.Sand)) 20mm thick mixed with WPC at 2% by weight of cement used and top pointed with the same red oxide mixed mortar etc complete, as design complying with standard specifications

Supplying and fixing ornamental stone vangal of size 0.15mx0.10m and length 0.40m will be fixed on brick masonry wall with cutting the wall etc.,and levels should be checked and position fixed with cement mortar. Vangal stones will be rough finished and pointed with rich cement mortar etc.,The rate for the above works including labour charges,scaffolding work,material charges and conveyance charges etc., complete complying with standard specification.

Supply and fixing of carved cut stone Pedestal for all wooden columns in size 300mm x 300m with 150 mm height

The ornamental stone works of Pillars by stone sthapathy for the following works to be carryon. To fix the stone pillars of the size 20cmx20cm in bottom 15cmx15cm in top and height 210cm will be placed on the stone base of size 30cmx30cmx15cm by using grooving method. All the stone pillars will be checked horizontality,verticality and levels by using plumb line,square and level. The above all works as per the direction of departmental officers. The rate for the above works including labour charges,scaffolding work,material charges and conveyance charges etc., complete complying with standard specification.

Providing and Fixing the Wooden Rafter Beams of different sizes for supporting on roof Tiles and sunshade tiles. The rate inclusive of all materials, labour power and conveyance of materials to the work site, loading & unloading etc., and as per drawing and design by the Departmetnal Officers and All the materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (one cement and three Crushed Stone Sand (M.Sand)) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

UPVC Ventilator Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing in postion of 35mm thick solid core flush door shutters single leaf with TW ply on both sides and with TW lipping of size 35x12mm on all edges with necessary adhesives and C.P. Screws Alu. Butt Hinges (3 nos. 250 x 16 mm Size) Alu. Aldrop1 No. 250 x 16 mm Size, Alu. Tower Bolt 1 No. 250 x12 mm size, alu. Tower Bolt 1 No. 200 x 12 mm size, D type alu. Handle 200mm length 1 No., alu. door stopper with rubber bush 1 No. shall be provided, as directed by the departmental officers etc., complete.

Paving the floor with Granite slab of size 1200 X 600mm and above in CM 1:3, 18mm thick Granite slab (Flammed Finish) for flooring including cost of material and labour for laying and jointing etc all complete complying with standarad specification

Renewing and fixing Eaves board of size 25 cm x 2 cm using teak wood of best quality as per existing style including cost of teakwood , labour wrought and putup, labour charges for fixing in position etc. complete complying with standard specifications

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (one cement and three Crushed Stone Sand (M.Sand)) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best quality vetrified (Morbonite) Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

provision of Cornices with moulding, decorative bands using cement mortar (1:3 Cement Mortar and finishing it with fine mortar using brick masonry set in 1:0.5: 3 Cement mortar, plastered with 1:3 CM finished with 1:2 fine ground CM) including inserting brick pieces, making templates to match the original work etc complete up to 450 mm thick/wide

Dadooing walls with following best approved quality, coloured glazed tiles of 300mm x 200mm x 6mm sizes set in Cement Mortar 1:2 (One Cement and Two Crushed Stone Sand (M.Sand)) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Providing and laying mangalore tiles on the sloped pitched roof whereever required, above double layered wooden reapers, flat ceiling tiles ensuring no water leakage and as specified by Conservation Architect and engineer. (approved heritage data)

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Providing and Fixing 4mm Th. Coloured glass using wooden square beeding, polished finished with melamine polish the colour and and texture of glass to be approved conservation architect or Engineer in charge.

Manufacturing, supplying and fixing in position plain cement concrete precast pavement slab of size 450mm x 450mm of 50mm thick in Cement Concrete 1:2:4 (One cement, Two sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three Sand) to full depth of slab etc., complete complying with standard specification and as directed

kadal constructions

PMA CONSTRUCTIONS