PROVISION OF OTM ACCN PHASE-II AT ICGAS RATNAGIRI

Amount

SCHEDULE "A" Part - I (BUILDING WORKS) Total of Schedule 'A' Part-I B/F from serial Page No 22(R).

SCHEDULE "A" PART-II (SITE CLEARENCE, AREA DEVELOPMENT, EXCAVATION & EARTH WORK) Total of Schedule 'A' Part-I B/F from serial Page No 23(R).

SCHEDULE "A" PART-III (INTERNAL WATER SUPPLY) Total of Schedule 'A' Part-I B/F from serial Page No 24(R).

SCHEDULE "A" PART-IV (INTERNAL ELECTRIC SUPPLY) Total of Schedule 'A' Part-I B/F from serial Page No 27(R).

SCHEDULE "A" PART-V (ROAD/PATH/CULVERT) Total of Schedule 'A' Part-I B/F from serial Page No 30(R).

SCHEDULE "A" PART-VI (SEWAGE DISPOSAL) Total of Schedule 'A' Part-I B/F from serial Page No 32.

SCHEDULE "A" PART-VII (AREA DRAINAGE) Total of Schedule 'A' Part-I B/F from serial Page No 33(R).

SCHEDULE "A" PART-VIII (COMPOUND, CHAIN LINK FENCING & GATE) Total of Schedule 'A' Part-I B/F from serial Page No 37(R).

SCHEDULE "A" PART-IX (SOLAR WATER HEATING) Total of Schedule 'A' Part-I B/F from serial Page No 38.

SCHEDULE "A" PART-X (EXTERNAL ELECTRIFICATION) Total of Schedule 'A' Part-I B/F from serial Page No 42 (R)

SCHEDULE "A" PART-XI (EXTERNAL WATER SUPPLY) Total of Schedule 'A' Part-I B/F from serial Page No 43.

SCHEDULE "A" PART-XII (LIGHTNING PROTECTION) Total of Schedule 'A' Part-I B/F from serial Page No 44(R).

SCHEDULE "A" PART-XIII (FIRE FIGHTING) Total of Schedule 'A' Part-I B/F from serial Page No 48(R).

SCHEDULE "A" PART -XIV Note:- This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col.' E ' signifies this fact only.

INTERNAL WATER SUPPLY

Supply & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS:8931. 15 mm nominal bore

Supply & fixing C.P. brass Two-way angle valve 15 mm nominal bore for EWC/AIWC points & for fixing Ablution Health Fauct of approved quality conforming to IS:8931.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

INTERNAL ELECTRIFICATION

S & F modular type 1 module RJ 11 telephone socket with shutter complete all as specified and directed. Make: Legrand Arteor Cart-Part No. 5734 26 or equivalent model of Precision or other make approved by GE

S & F modular type 1 module TV socket complete all as specified and directed. Make: Legrand Arteor Cat-Part No. 5734 25 or equivalent model of Precision or other make approved by GE

S & F 32 A panel mounted (2P + E) angled socket, conforming to IEC 60309- 1 & 60309- 2, having IP 67 ingress protection & IK 08 impact protection suitable for 250 V, 50 Hz electric supply complete as specified and directed. Make: Schneider PratiKa Cat-Part No. PKF32F423 or equivalent model of Legrand or Havells

S & F modular type bell ding dong of 2 module size, conforming to IS: 8884- 1978 complete all as specified and directed. Make: Legrand Arteor Cat-Part No. 5734 43 or equivalent model of Havells or Anchor

S & F modular type bell ding dong of 12 module size, conforming to IS: 8884- 1978 complete all as specified and directed. Make: Legrand Arteor Cat-Part No. 5757 70 or equivalent model of Havells or Anchor

S & F modular type bell ding dong of 18 module size, conforming to IS: 8884- 1978 complete all as specified and directed. Make: Legrand Arteor Cat-Part No. 5757 90 or equivalent model of Havells or Anchor

S & F 10 W surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed. Make: BAJAJ Cat-Part No. 112407 BCLSB 10 WH or equivalent model of Havells, Philips or Wipro

S & F 20 W surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed. Make: BAJAJ Cat-Part No. 112785 BCLAB 20W or equivalent model of Havells, Philips or Wipro

S & F 2 X 20 W surface/wall mounted LED batten having complete internal wiring suitable for retrofit LED tube light with double side connections, powder coated CRCA sheet steel housing, white powder coated CRCA sheet reflector, push-fit type white polycarbonate lamp holders with corrosion resistant brass contacts having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, along with 20 W LED polycarbonate tube light having high efficiency long life SMD LED module with luminous efficacy of > 100 lumen/W, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, high quality polycarbonate end caps and polycarbonate housing in opal finish including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed. Make: BAJAJ Cat-Part No. 112688 BJI 218 LED PC & 112481 BRLB 21W CWc or equivalent model of Havells, Philips or Wipro

S & F 12 W recessed mounted round shape LED downlight having long life SMD LED mounted on MCPCB with high LED efficacy of > 85 lumen/W, high quality polycarbonate opal concave diffuser, high reflective polycarbonate conical shaped reflector, integral SPMS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, housed in white powder coated pressure die-cast aluminium heat sink and white finish polycarbonate ring for holding the diffuser having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed. Make: BAJAJ Cat-Part No. 112671 BPSLR 12W WH or equivalent model of Havells, Philips or Wipro

S & F 43 W recessed mounted square shape 2' X 2' LED panel having high efficiency long life LED package in integral module with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, high transmittance polystyrene opal diffuser, housed in white powder coated pressure die-cast aluminium heat sink having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed. Make: BAJAJ Cat-Part No. 112669 BZRSQL 43W GZ1 NW or equivalent model of Havells, Philips or Wipro

S & F 45 W LED street light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of ≥ 100 lumen/W, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high effiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, pole mounting with bracket arm OD 35 mm to 42 mm including necessary electrical connection to the fixture with 3 core flexible Cu conductor cable of appropriate size and 1.5 m long bracket, having 40 mm diameter light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed. Make: BAJAJ Cat-Part No. BAJAJ 169799 BRTFG 45W LED I or equivalent model of Havells, Philips or Wipro

S & F BEE five star rated energy efficient high-speed ceiling fan having 1200 mm blade sweep, air-flow not less than 210 CMM, operating voltage 220-240 V and frequency 50 Hz, including a downroad of suitable size and electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fan complete all as specified and directed. Make: Crompton Cat-Part No. ENTRUST50 or Havells Cat- Part No. ES-50 or equivalent model of Usha or BAJAJ

S & F BEE five star rated energy efficient high-speed ceiling fan having 1400 mm blade sweep, air-flow not less than 210 CMM, operating voltage 220-240 V and frequency 50 Hz, including a downroad of suitable size and electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fan complete all as specified and directed. Make: Havells Cat- Part No. SS-390 or equivalent model of Usha , Crompton or BAJAJ

S & F engery efficient non-metalic fresh air fan having blade sweep 250 mm, air delivery not less than 860 CMH, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fresh-air fan complete all as specified and directed. Make: Crompton Cat-Part No. VENTILUS 10" or equivalent model of Usha, Havells or BAJAJ

S & F engery efficient metalic exhaust fan having blade sweep 450 mm, air delivery not less than 6000 CMH, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fresh-air fan complete all as specified and directed. Make: Crompton Cat-Part No. EXHD450- 4-1 or equivalent model of Usha, Havells or BAJAJ

Vertical triple pole and neutral DB, 4- way Make: Schneider Cat-Part No. A9HVD12H or equivalent model of Legrand or Havells

Vertical triple pole and neutral DB, 12- way Make: Schneider Cat-Part No. A9HVD12H or equivalent model of Legrand or Havells

Vertical triple pole and neutral DB, 8- way Make: Schneider Cat-Part No. A9HVD08H or equivalent model of Legrand or Havells

S & F ISI marked MCB for AC applications till 63 A, having breaking capacity Icn = 10 kA, conforming to IS/IEC 60898-1-2002, sliding bottom clamp, colour coded on/off indication on dolly, biconnect IP 20 protected lower terminals and sliding shutters, all complete as specified and directed. 6 A, SP MCB, C- curve Make: Schneider, Legrand, Havells

S&F 10 A, SP MCB, C- curve

S&F 16 A, SP MCB, C- curve

S&F 16 A, SPN MCB, C- curve

S&F 32 A, SP MCB, C- curve

S&F 32 A, SP MCB, C- curve

S&F 32 A, SPN MCB, C- curve

S&F 63 A, TP MCB, C- curve

S&F 63 A, FP MCB, C- curve

S&F 63 A, SP MCB, C- curve

S&F 63 A, SPN MCB, C- curve

S&F 125 A, TP MCB, C- curve

S & F FP MCCB 400 Amp with adjustable overload settings, adjustable short-circuit settings, adjustable earth- fault settings, current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit complete as specified and directed. Make: Legrand, Schneider, Havells

250 A, 415 V, Ics = Icu = 36 kA, 50 Hz, FP MCCB with adjustable overload settings (0.36- 1 X In) & tr = 0.5 - 16 s, adjustable short-circuit settings (1.5 - 10 X Ir), adjustable earth- fault settings (0.2- 1 X In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit.

160 A, 415 V, Ics = Icu = 25 kA, 50 Hz, FP MCCB with adjustable overload settings (0.36- 1 X In) & tr = 0.5 - 16 s, adjustable short-circuit settings (1.5 - 10 X Ir), adjustable earth- fault settings (0.2- 1 X In), current limiting type double break roto active type, instanteneous protection and microprocessor based trip unit.

SEWAGE DISPOSAL

RCC septic tanks with upflow filter designed to carry sewage and sullage water , exc in any type of soil, foundation in PCC 1:4:8 below foundation , RCC M:30 , Design Mix in walls , Base slab , baffle walls and Roof slab including Beams etc with vent shaft , Manhole openings with cover connection etc, complete with effective depth of 1.5 mtr and overall depth of 3.0 mtr for 150 Users & including filter beds for 150 users

RCC septic tanks with upflow filter designed to carry sewage and sullage water , exc in any type of soil, foundation in PCC 1:4:8 below foundation , RCC M:30 , Design Mix in walls , Base slab , baffle walls and Roof slab including Beams etc with vent shaft , Manhole openings with cover connection etc, complete with effective depth of 1.5 mtr and overall depth of 3.0 mtr for 100 Users & including filter beds for 100 users

RCC septic tanks with upflow filter designed to carry sewage and sullage water , exc in any type of soil, foundation in PCC 1:4:8 below foundation , RCC M:30 , Design Mix in walls , Base slab , baffle walls and Roof slab including Beams etc with vent shaft , Manhole openings with cover connection etc, complete with effective depth of 1.5 mtr and overall depth of 3.0 mtr for 50 Users & including filter beds for 50 users

SOLAR WATER SUPPLY

Supplying, Installing, Testing and commissioning of solar hot water system (Flat plate collection) based on indirect transfer of heat of capacity 100LPD with electric heating capacity back up of 2 KW and stagging height as per OEM recommendation made out of angle/flat iron duly painted complete.

Fabrication /fixing of water tank staging made out of MS Angle iron 50x50x6mm/MS Flat iron 50x6mm thick including supporting MS Plate ( Appx 1 SqMtr) of 6mm thick on top of structure as the base for PVC syntex tank with necessary angle iron ladder with proper PCC foundation including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed

EXTERNAL ELECTRIFICATION

Supply,Installation,testing and commissioning of outdoor ONAN type transformer having 33KV/11 KV voltage levels and of 1000 KVA,3 PH,3 Wire,50 Hz dd HT side- delta & LT side- delta connection,Z=4.5%with OCTC all as per IS 2026 alongwithfirst fill of Oil,all accessories and components as per specification/data sheet,drawings and all applicable standard.Termination cable box at HT side to terminate XLPE cable and LT side suitable for terminating cable complete all fitting and accessories .Handling, unpacking, erection, alignment,assembly of accessories,application of touch up paint,connection of auxilary circuits,oil filtration & filling of transformer oil complete with all labour,tools &tackles,consumbles including minor civil works etc as per drawings/specification and as instructed by Engineer in charge mounting chanels foundation bolts,inter connection between accessories mounted on the transformer & marshalling box,checking of foundation level, welding of stoppers on foundation channels including all labour and materials. (Make- ITE/VOLTAS/CROMPTON GREAVES)

Supply,Installation,testing and commissioning of outdoor ONAN type transformer having 11KV/0.433 KV voltage levels and of 800 KVA,3 PH,3 Wire,50 Hz dDYN 11 vector group HT side- delta & LT side- star connection,Z=4.5%with OCTC & RTCC all as per IS 2026 alongwithfirst fill of Oil,all accessories and components as per specification/data sheet,drawings and all applicable standard.Termination cable box at HT side to terminate XLPE cable and LT side suitable for terminating cable complete all fitting and accessories. Handling, unpacking, erection, alignment, assembly of accessories,application of touch up paint,connection of auxilary circuits,oil filtration & filling of transformer oil complete with all labour,tools &tackles,consumbles including minor civil works etc as per drawings/specification and as instructed by Engineer in charge mounting chanels foundation bolts,inter connection between accessories mounted on the transformer & marshalling box,checking of foundation level, welding of stoppers on foundation channels including all labour and materials. Note : Contractor of his electrical engineer must have electric licence from the MSEB. The relation of electric connection from MSEB to make the transformer functional by the contractor under his own arrangement.

S&F 33 KV CT/PT metering cubicle unit with 3 phase 4 wire metering arrangment as per electric department approval drawing and spefification consisting of 03 Nos resin cos5t CTs of ratio 50/5 Amps class 0.5 15 VA STC 6.7 KA fpr 1 sec and 03 Nos PTs of ratio 33 KV/√3 / 110 v/√3 class 0.5 100 VA of department approved make duly tested by MSEB complete with internal wiring with HT instulated copper bus bars duly powder coated with 4 Nos GI pipes MS plate mounting poles complete all as specifioed. Note : Metering cubicle will be got approved from MSEB by the contractror and certificate there off will be produced to the GE.

Supply & fix Trivector meter three phase four wire TVM 110 Volt , 1 A/5A ,class 0.2 with box. Note : Trivector meter will be got approved from MSEB by the contractor and certificate there off will be produced to the GE.

Supply, laying & testing and commissioning of power cable of size 300 Sqmm X 3 core, 33 KV Earthed grade aluminium conductor screened,XLPE insulated,round wire GI armoured and PVC extruded inner sheathedand FR outer sheathed cable confirming to IS 7098 all as specified as directed.

Supply and fix cable jointing kit for 33 KV grade cable for indoor termination joint complete with jointing material and accessories suitable for 3 core XLPE armoured Al conductor cable of size 300 sq mm .

Supply and fix cable jointing kit for 33 KV grade cable for outdoor termination joint complete with jointing material and accessories suitable for 3 core XLPE armoured Al conductor cable of size 300 sq mm .

Supply and fix cable jointing kit for 1.1 KV grade cable for indoor termination type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured Al conductor cable of size 500 sq mm .

Supply and fix cable jointing kit for 1.1 KV grade cable for outdoor termination straight joint type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured Al conductor cable of size 300 sq mm .

S & F LED street light fitting 72 Watt,240 V with cast aluminium housing complete including bracket made out of 32 mm dia GI pipe light grade, and necessary clamp,bolts and nuts etc complete all as specified and directed.

S & F SMC box size 200 X 140 X 95 mm internal size with hinged door (L) with 1 No PVC connector 4 way 16 amps & 1 No MCB SP 6 Amps including fitting brackets etc.

Supply & Fix PVC insulated PVC roundl sheathed copper conductor (flexible) cable size 1.5 sqmm X 3 core,1100 Volt from street light junction box to fitting complete all as specified and directed.

Supply and instalation & testing of fast earth electrode maintenance free chemical earthing of Dual pipe technology of 3 mtr long with outer pipe diameter of 80 mm & inner pipe diameter 48 mm ,the pipes are properly galvanized for 80-120 micron and wall thickness of inner pipe 3mm and 2 mm of outer pipe .There should be terminal for connection of 75X6 mm with two holes of 14 mm diameter.FAST ELECTRODE is dully fitted with the highly conductive material with sealing at both ends with lead terminals of 75X6 mm at top.Alongwith 2 bags of 2 Kgs each of earth Enhancing Compound.The chemical compound should be tested and certified. by any international accredited laboratory.The testing laboratory should be ISO 9001 &iso 14001 Certified. The eartenhancing compound should be tested referring to protocol IS 1350 &IEC62321/111/54/CDV. The PH value of compoundshould be between 7 to 8.The content of mercury(Hg) & Hexacromium should be below detection level.The electrode should be tested for salt spray test as per BIS 117-09 for corrosion for minimum 500 Hrs.The FAST ELECTRODE shall be dully tested & certified by CPRI (Central power Reserch Insititute),Govt of India for a minimum short circuit current of 42 K Arms for 1 second with initial pick of 88.2 KA. The FAST ELECTRODE must be approved by the PWD,Maharastra,and MSDCL infra.

Supply and fix UPS for 30 min back up three phase AC input 360 to 460V and out put 415 V ± 1% of capacity 10 KVA, battery 12 V/26 AH 20 Nos and MS battery rack open type all as specified and directed.

Supply and fix Astro time switche 230 V ,single Phase cat part no AUTS02AST00 of L&T make complete all as specified and directed.

DG SETS

Supplying, installing, testing and commissioning factory assembled silent Diesel Engine driven generators set, fully wired alternator AC to give an out put of 750 KVA continuously rating at a PF of 0.8 logging, 415 volts, AC 3 Phase 4 wire 50 H2 +/- 01% supply , 1500 RPM directly coupled with diesel engine water cooled mounted on common base frame complete with floor mounting free tank (service tank) of adequate capacity with free line and accessories PCC foundation work as per manufacturies instuctions, vibration damper pads. Control Panel and other accessories etc and comprising of following:- (A) Diesel Engine:- Water cooled turbo charge with after cooler to deliver suitable BHP at 1500 RPM confirming to BS 5514 and conforming to IS 10000 an overload capacity of 10% for one hour in any 12 continious hours operation with the following accessories:- Make:- Kirloskar Model No DV12ETA G1 or equivalent of Greaves Ltd/Cummins India Ltd)/Jackson (a) Radiator with blower fan or heat exchanger with guard (b) Pipe coupling for engine cooling system piping (c) Corrosion inhibitor coolant (d) Lube oil filters (e) coolent capacity not less than 145 Ltrs (f) Minimum bore V strocke (130 X150) mm. (g) Fly wheel housing and fly wheel to suit alternator (h) Engine bearing mechanism in fly wheel and starter ring.

Contd from 20.01........) (j) Dry type air cleaners and vacuum indicators (k) Motor driven primary pump (l) Battery charging alternator (m) Exhaust piping made out of STIC C class, MS pipe inclusive of all accssories and hardware, necessary support scaffolding as per manufacture's recommendations to sustain back pressure with rain cap. (n) Lub oil cooler. (o) 12 V electric stater motor (p) Fuel pump with Electronic governor. (q) First fill of oil, coolent and diesel during commissioning and 12 hours testing. (r) Inter connecting copper cabling of adequate capacity between batteries control. Electronic Instrnment panel complete with all accessories as per manufrastructure's specificants displays the following: - (i) On/Off/Start key. (ii) Battery charging voltmeter. (iii) Electronic hour meter. (iv) Indication and monitoring of oil pressure & safety trip in case of law oil pressure. (v) Indication and monitoring of collant Temperature & safety tripin care of high coolant Temp. (vi) In built Engine shutdown system in case of over speed. (vii) Indication & monitoring of fuel level and alarm system (s) Battery. 2x12 Volts pre-charged PP batteries with lead. (viii) Fuel pump =01 Nos (rotary type)

(Contd from 20.02.......) (t) Fuel Tank. Minimum 8 hours fule load diesel storage capacity fuel tanks with minimum capcity of 1000 Ltr dully fixed on PCC platform (or) Angle iron structure with ladder or steps for refilling etc.Mounting brackets, factory made of 14 SWG thick MS sheet with level indicator fuel Inlet, fuel outlet, airvent drain plug, in let arangment for diesel filling from exterior of canopy (without opening its Pavel) etc complete all as specified.

(Contd from 20.03.......) Alternator. Alternator of suitable rated of 750KVA at 0.8PF, 415V, 3 phase, 4 wire, 50 cycles/sec 1500RPM, self excited and self regulated regulation + 01% of rated voltage, From no load to full load, insulator class-H & IP-23. The alternator conforwk to BS-2613/IS 4722 and IEC-34-I Make- Kirloskar.

(Contd from 20.04.......) Green Canopy: - Construction of Acoustic Enclosure for said DG Set of cap 750KVA shall be powder coated and fabricated out of 1.5mm thick MS sheet. The silent canopy shall be of nut bolt type. Canopy Panel and door shall have inside living of Fire Retardent foam as acoustic material to reduce noise level to 75db measured at 1.00 meter distance for available frequency as per guidelines of Centre Pollution Control Board. The size of canopy be suitable for 6800x2300x2713(b) Civil Work. All civil work related to foundation, installation including Base frame will as per manufrastructure design and be included in coded rate of item.

Supplying, installing, testing and commissioning factory assembled silent Diesel Engine driven generators set, fully wired alternator AC to give an out put of 30 KVA continuously rating at a PF of 0.8 logging, 415 volts, AC 3 Phase 4 wire 50 H2 +/- 01% supply , 1500 RPM directly coupled with diesel engine water cooled mounted on common base frame complete with floor mounting free tank (service tank) of adequate capacity with free line and accessories PCC foundation work as per manufacturies instuctions, vibration damper pads. Control Panel and other accessories etc (Gen set Make : KGI-30 WS of Kirloskar (koel green) required and comprising of following:- (A) Diesel Engine:- Water cooled turbo charge with after cooler to deliver suitable BHP at 1500 RPM confirming to BS 5514 and conforming to IS 10000 an overload capacity of 10% for one hour in any 12 continious hours operation with the following accessories:- Make:- Kirloskar Model No 3R1040TG1 or equivalent of Lumminus/Eicher (a) Radiator with blower fan or heat exchanger with guard (b) Pipe coupling for engine cooling system piping (c) Corrosion inhibitor coolant (d) Lube oil filters (e) coolent capacity not less than 14.5 Ltrs. (f) Minimum bore V strocke (105 X120) mm. (g) Fly wheel housing and fly wheel to suit alternator (h) Engine bearing mechanism in fly wheel and starter ring.

(j) Dry type air cleaners and vacuum indicators (k) Motor driven primary pump (l) Battery charging alternator (m) Exhaust piping made out of STIC C class, MS pipe inclusive of all accssories and hardware, necessary support scaffolding as per manufacture's recommendations to sustain back pressure with rain cap. (n) Lub oil cooler. (o) 12 V electric stater motor (p) Fuel pump with Electronic governor. (q) First fill of oil, coolent and diesel during commissioning and 12 hours testing. (r) Inter connecting copper cabling of adequate capacity between batteries control. Electronic Instrnment panel complete with all accessories as per manufrastructure's specificants displays the following: - (i) On/Off/Start key. (ii) Battery charging voltmeter. (iii) Electronic hour meter. (iv) Indication and monitoring of oil pressure & safety trip in case of law oil pressure. (v) Indication and monitoring of coolent Temperature & safety tripin care of high collant Temp. (vi) In built Engine shutdown system in case of over speed. (vii) Indication & monitoring of fuel level and alarm system (r) Battery. 1x12 Volts pre-charged PP batteries with lead.

(s) Fuel Tank. Minimum 8 hours fule load diesel storage capacity fuel tanks with mounting brackets, factory made of 14 SWG thick MS sheet with level indicator fuel Inlet, fuel outlet, airvent drain plug, in let arangment for diesel filling from exterior of canopy (without opening its Pavel) etc complete all as specified.

Alternator of suitable rated of 30KVA at 0.8PF, 415V, 3 phase, 4 wire, 50 cycles/sec 1500RPM, self excited and self regulated regulation + 01% of rated voltage, from no load to full load, insulator class-H & IP-23. The alternator confirm to BS-2613/IS 4722 and IEC-34-I Make- Kirloskar/Crompton Greaves.

Construction of Acoustic Enclosure for said DG Set of cap 30KVA shall be powder coated and fabricated out of 1.5mm thick MS sheet. The silent canopy shall be of nut bolt type. Canopy Panel and door shall have inside living of Fire Retardent foam as acoustic material to reduce noise level to 75db measured at 1.00 meter distance for available frequency as per guidelines of Centre Pollution Control Board. The size of canopy be suitable for 6800x2300x2713(b) Civil Work. All civil work related to foundation, installation including Base frame will as per manufrastructure design and be included in coded rate of item.

LIFTS

Design, Supply, Install, Testing and commissioning passenger lift machine room less type suitable to carry 15 Passnager (1020 Kg) at a speed 1.5 mtr per second, lift with single speed motor 415 volts, 3 Phase, AC 50 H2 supply conforming to IS-14665 suitable to serve G + 05 upper floor with AC variable voltage and variable frequency drive (vvv f drive) complete with all standard accessories simplex automatic and manual dual controlled operation with/withoutattendant, centre openign doors with door drive (Electric motor dirven mechanism) sliding stainless steel doors, automatic rescue drive (ARD) system. 3D infrared sensor in full height of door and built in announcing system without hand set (05 Nos, one each in car and near ground floor landing door complete all as specified.

Design, Supply, Install, Testing and commissioning passenger lift Machine room suitable to carry 08 Passnager (544 Kg) at a speed 1.5 mtr per second, lift with single speed motor 415 volts, 3 Phase, AC 50 H2 supply conforming to IS-14665 suitable to serve G + 05 upper floor with AC variable voltage and variable frequency drive (vvv f drive) complete with all standard accessories simplex automatic and manual dual controlled operation with/without attemdamt, centre openign doors with door drive (Electric motor dirven mechanism) sliding stainless steel doors, automatic rescue drive (ARD) system. 3D infrared sensor in full height of door and built in announcing system without hand set (05 Nos, one each in car and near ground floor landing door complete all as specified.

EXTERNAL WATER SUPPLY

Supply and laying of ductile iron pipe, spigot and socketed including specials class K-7 complete all as specified of size 150 mm diaconfirmiong as per IS complete with all accessories & fittings. Note :- Excavation and Joints will be measured and paid for seperately under respective item. Make-Jindal/Electro steelcasting/Lanco

M&l for DI fittings such as bends (any type, radius and angle Tapper any type(Straight, bends increasing, decreasing or double socket etc), Tee piece, single branch, Y Juction double branch, Cross (all socket or socet and spigot or flanged, collers, caps and plug etc comlete all as specified. Make-Jindal/Electro steelcasting/Lanco

S&F CI NRV with bye pass arrangement suitable for 80 mm bore pipe completed all as specified.

S&F CI NRV with bye pass arrangement suitable for 150 mm bore pipe completed all as specified.

Supply & fixing sluice valve of following size duly flagged and confirming to IS-14846 and of class PN 1.6 completed as as specified :-

(a) 150 mm dia

(b) 80 mm dia

S&F bulk water meter CI body suitable for 80 mm bore pipe line all as specified and directed

S&F CI Air release valve with single air out let conforming to IS-14845 of size 50 mm bore and cast iron water suitable for mains of 150 mm dia complete all as specified.

M&L for construction of brick massonry valve pit chamber of size 90 X 90 X 90 CM (Internal) complete with 3 mm thick MS Sheet cover and 50 X 50 X 6 mm angle iron frame duly painted with two coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement complete all as specified.

M&L for construction of brick massonry valve pit chamber of size 60 X 60 X 60 CM (Internal) complete with 3 mm thick MS Sheet cover and 50 X 50 X 6 mm angle iron frame duly painted with two coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement complete all as specified.

Supply, install, test and commissioning pump set centrifugal monoblock, electric driven 3 phase 415V, 50 HZ 450 LPM at 50 mtr head complete with starter panel having suitable type automatic starter, Individual control MCBs and main control MCCB, digital type volt meter, digital type Ammeter indicator lamp etc. with necessary suction side GI pipe medium grade, GM floot valve & PCC foundation etc. complete all as specified. For -02 Nos main pump house for living, 02 Nos for ATC and 02 Nos at ATC Pump House)

Supply install test and commissioning micro processor based constant current technology water disinfection equipment using silver ionisation process based on oligodynamic technology, suitable to provide directly to pumping main or to sump or to over head tank. The water chamber is to be made of corrosion free stain less steel pipes and inverstment casting fittings conforming to SS 304 capable to withstand a pressure of 10 KSC and with in built silver electrodes made from pure silver after proper metallurgical treatment and chemical treatment for dissipation of minute ionic silver disinfectant suitable for dual ionisation plant of 2.5 lakh litres capacity. This silver electrode must be fixed on a PVC/nylon strips which will also be non toxic to humans. All this will be mounted in powder coated mild steel cabinet of 1.6mm thick with universal lock and key for safety. The control panel with electrode OK indication to show that the electrode is working clear electrode indication to show that the electrode is clogged and change electrode indication to show that the electrode is nearing completion for easy maintenance of the equipment. The disinfectant produced by the electrode is totally non toxic at the dosed levels as prescribed by WHO (World Health Organisation) standards. The equipment is suitable to operate on single phase 220 Volts, 50Hz power supply. The life of electrode shall be 900 million liters with the dosage of 0.01 PPM of silver complete all as specified & directed.Note- The contractor will supply testing kit as per manufacturer specification.

LIGHTNING PROTECTION

Supply and installation of fast earth electrode 3.0 mtr length size model F84, having two M S pipe one inside the other with proper not deep galvanished outer dia 88 mm and inner dia 48 mm and the cavity between the rod pipes is filled with ground resistance improment powder, sealed with both end the outer pipe of electrode should be zink coated, the electrode should burried directly in the ground by making boring of diameter 10'' with boaring machine highly conductive non magnetic and non corrives is to be connected with GI strip 25 X 3 mm of 2 to 3 mtr length to facilitet further connection to earth dolly and provision of earthing chamber in bricks wall size 45 x 45 x 15 cm an dhaving PCC cover of required size complete all as directed and all as per IS 3034 (1981) Note: GI strip to be measured andpaid seperately.

AIR CONDITIONING

Supply and install split AC units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and filter for better indoor air plasma quality of capacity 2TR and of 3 star rating.

Supply and install voltage stablizer for automatic operation, single phase copper wound naturally air cooled indoor type and desingned for input variation between 170 volt to 260 volt with output voltage stablized at 220/230 volt with accuracy of 2.5% of capacity 5 KVA. Note:- Point wiring will be measured and paid for seperatelly.

COOLING APPLIANCES

Supply, Installation testing and commissioning of water cooler partialy stainless steel, electric driven single phase having approximate storage cap 80 ltrs and cooling cap 40 ltrs per hours.(Make- Blue star/Usha/Voltas)

Note :- For item No 1 PCC work and point wiring will be measured seperatelly under respective items.

Supply, Installation testing and commissioning of refrigerator, electric driven single phase and cap 310 ltrs, duly BEE 3 star rated etc complete all as specified. Make - LG/Samsung/Whirlpool

Supply, Install testing and commissioning of hard glass top deep freezer 210 ltrs single phase 240 volts 50 HZ, complete all as specified. Make - LG/Samsung/WhirlpoolMake - Blue Star

Supply and fixing voltage stablizer for automatic operator single phase copper wound naturally air cooled indoor type and design for input variation between 170 to 260 volts with output voltage stablized at 220 volts with accuracy 2.5% of following capacity:- ( Make-V-guard)

(a) of cap 1 KVA

(b) of cap 0.5 KVA

AVIATION LIGHT

Supply and fix aviation obstruction LED type of Bajaj cat No 110731 BGAV 302 LED, 240 V, with timer switch of indioasian Cat No SUL 180a and one No 10 A, MCB, SPN 230 V fixed in a hensel enclousre.

M&L sub main wiring of PVC insulated unsheathed two single core 2.5 sqmm copper multi stranded conductor including one run of single core copper conductor of size 1.5 sqmm as earth wire drawing into PVC conduit medium grade 25 mm dia,ISI marked for sub main wiring concealed in wall /roof etc . with required accessories complete all as specified and directed.

FIRE FIGHTING

Active Full function Repeater panel complies with EN54-2, Network up to 64 panel/repeater, Programmable one touch test mode, Powerfull and versatile cause and effect programming,Cause and effect wizard including:Cause and effect action,Disablement comfiguration, Test mode comfiguration 5.25 amp power supply to EN54 part 4, Large graphic display,in built help and alarm information screen, Real time clock,Stylish enclosure design,Soft touch tactile buttons 2 Programmable function buttons, 3 Programmable front panel mounted LEDs, Improved front loading printer(optional) Up to 512 Programmable inputs and Output Perpanel via 2 wire RS485 serial link (Optional ) SimpleWindows grafical configuration utility and IP 30 protection.

Supplyand installation, testing and commissioning of 2C x 1.5 Sq.mm twisted pair copper cable ISI marked with proper clamping, supports and terminations..

Supply and Installed foam cylinder high pressure seamless steel gas flat type concave bottom as per IS-7285 of capacity 140 Ltr.

Supply and Installed foam cylinder high pressure seamless steel gas flat type concave bottom as per IS-7285 of capacity 100 Ltr.

Supply and Installed foam cylinder high pressure seamless steel gas flat type concave bottom as per IS-7285 of capacity 80 Ltr.

Supply, installation, testing and commissioning of following types of extinguisher with provision of wall bracket (fixed with anchor fastner). As per IS 15683 - Dry chemical Powder type 09 Kg

Supply, installation, testing and commissioning of following types of extinguisher with provision of wall bracket (fixed with anchor fastner). As per IS 15683 - Mechanical Foam type 09 Kg

Supply, installation, of fire bucket (dry sand) As per IS 15683

Supply and Installed foam cylinder high pressure seamless steel gas flat type concave bottom as per IS-7285 of capcity 67.50 Ltr.

Supply and Installed NOVEC 1230 fire extinguishing solution/fluid for suppression system,non corrosive,non toxic,non-explosive,non flamble and harmless to people health as per EN standards and VDS/CNPP certificate complete all as per fire safety standards.

Supply and Installed master cylinder comprising of pressure guage with low pressure supervisory switch,pnuematic/manual actuator,flexible discharge hose including necessary connection etc complete.

Supply and Installed slave cylinder comprising of pressure guage with low pressure supervisory switch,pnuematic/manual actuator,flexible discharge hose including necessary connection etc complete.

Supply and Installed check valve as per manufacturers guidelines for distribution for NOVEC 1230 ensuring high velocity and mixing in the surrounding air complete.

Supply and Installed discharge nozzle as per manufacturers guidelines for distribution for NOVEC 1230 ensuring high velocity and mixing in the surrounding air complete.

Supply and Installed pressure switch/press box for indication for passage of gas in the pipe suitable for operating pressure of max 220 bar and release pressure minimum 3 bar and having interupting cap 250 Vda/5 Amps etc complete.

Supply & Install microprocessor based gas release panel with duel function of detection and controll realease circuit operating on 220 V AC supply with battery backup with provision of audio/visual indications as per EN-12094-1/EN54-2+A1/EN54-4+A2 standard.

Supply & Fix manifold fabricated from ASTM-A106 seamless pipe all as per manufacturer recommendation all as per actual site condition.

Supply & Fix carbon steel seamless pipes confirming to ASTM A-106 Grde B Sch 40 in walls, ceilings including all bends and fittings and fixture for fixing to walls and celings.

AUDIO VIDEO AIDS

Supply and Fix Audio Vidio Aids complete system including Panasonic Projector,Projector Scrren,Sennheiser Microphone-XSW 35,Sennheiser Microphone-XSW 12,Marantz Amplifire,Klipsh 7.1 Speaker,Wireless Presenter etc. complete all as spcified and as directed.

Supply and Fix Philips LED 55" LED vidio wall Display ,Full HD ,Model No :- BDL 5588 XL complete all as spcified and as directed.

Supply and Fix computer Intel core I5 6 generation with gigabyte Motherboard,8 GB RAM ,1 TB Hard Disc , LG DVD Writer I Ball ATX Cabinet, I Ball Key board and optical mouse ,Dell 18.5 "LEDcomplete all as spcified and as directed.

NSC Projects Pvt. Ltd.

PUSHPA INFRACON

SOOD ASSOCIATES PVT LTD