GE 861 EWS-18/2022-2023

Amount

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed.

Demolition of brick work or stone boulder masonry built in cement mortar including all arches quoins etc but excluding ashlar facing, dressed stone work & precast concrete articles etc complete all as specificed and directed.

Demolition of cement concrete (unreinforced) in ground floors & paving n.exc 15 cm thick (below or above ground level) complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store complete all as specified and directed.

Demolition of cement reinforced concrete (reinforcement cut as required to facilitate demolition) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm complete all as specified and directed.

Taking down chowkat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each complete all as specified and directed.

Taking down shutter of any description area n.exc 1.00 sqm each complete all as specified and directed.

Taking down of shutter any description area exceeding 1 sqm but not exceeding 2 sqm each complete all as specified and directed.

Dismantling water tanks of any description exc 250 Ltrs n exc 500 Ltrs capacity and removing to storecomplete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

Demolition wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets & snap grid frame etc, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar, complete all as spcified and directed..

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads

Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:4, complete all as specified and as directed.

10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

15mm thick rendering on fair faces of brick or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Glazed ceramic coloured tiles 450mm x 350mm x 7mm/350mm x 250mm x7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Vitrified tiles 10 mm thick, light shade (square/rectangular) polished, area of each tiles exceeding 0.36 sqm not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Chequered coloured cement concrete tiles of size 200 x 200 x 25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed and including 10mm thick rendering in cement mortar 1:4 to receive, complete all as specified and directed.

20mm thick granite (of any type) tiles machine cut, in skirting/dado laid over 15mm cement screed in cement mortar 1:4 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete, complete all as specified and directed.

25mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crused stone aggregate) as in floors to recieve floor finishes, complete all as specified.

75mm thick PCC 1:3:6 Type C-2 (40 mm graded stone aggregate) as in sub-floor, sub-base, floor and pavings, etc., complete all as specified and directed.

Plain cement concrete M-10, 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 75mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

RCC M-25 design mix using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to sides and soffits of suspended slab such as roof slab, floor slab, shelves and similar works n. exc. 200 mms thick (Horizontal or sloping), finishing rough the concrete surfaces, complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, finishing rough the concrete surfaces, complete all as specified and directed.

MS TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

Mild steel work as in hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

Mild steel work as in framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed, worught, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

35 mm thick 2nd class hardwood plain (Sal/ Hollock) factory made, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats, complete all as specified and as directed.

35mm thick, 2nd class hard wood (Sal/ Hollock) factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

30mm thick, 2nd class hard wood (Sal/ Hollock) factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (b) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed.

Anodised aluminium snap grid of size 605 x605 mm frame work for false ceiling including straining with GI wire 4 mm thick, complete all as specified and directed.

10 mm thick PVC insulation panels with EPS stuck to 1mm thick plain PVC sheet suitably placed in false ceiling grid made of Aluminium/GI/MS as per specification and drawing, complete all as specified and directed.

Solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing, complete all as specified and directed.

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing, complete all as specified and directed

9mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work, complete all as specified and directed.

40mm thick , 2nd class hardwood planks, planed one side with butt joints and fixed with nails fixed in any situation, complete all as specified and directed.

2nd class hardwood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed.

2nd class hardwood, as in scantling and similar work, clean sawn, timber fixed in position including diamantling old unsv scantling, complete all as specified and directed.

2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm, complete all as specified and directed.

0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap with zinc coating of 275, fixed with 'L' or 'J' type or cranked hook bolts in roofs, walls etc. complete all as specified and directed.

0.63mm thick plain galvanized mild steel sheeting in ridges, hips valley gutters, drip and straight flashings (length and girth as fixed)with grade of zinc coating 275 complete all as specified and directed.

300mm size aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

200mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, aluminium handles, cast type, anodised, all as specified and directed.

100mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

75mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

300mm size mild steel helical door spring including roller & roller plate, complete all as specified & directed

150mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, complete all as specified and directed.

4mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.

4mm thick figured glass pin headed type and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples, complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples (fixed in repair), complete all as specified and directed.

25mm dia harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc., complete all as specified and directed.

Steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball, complete all as specified and directed.

S&F in repairs vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe), jointing to flush pipe complete and making good to floor in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed.

S&F in repair vitreous china urinals, bowl type 465x355x265 mm white, with grating and union for discharge pipe & fixing plugs, bedding urinal against wall in cement mortar 1:2, complete all as specified and directed.

S&F in repair grating doom 125 mm dia with waste hole of PTMT, complete all as specified and directed.

S&F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets, complete all as specified and directed.

S&F in repair vitreous china, wash hand basin, flat back of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, including 32mm dia PVC waste pipe, waste coupling and 15mm bore pillar tap,fancy type, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F in repairs swivel shower of PTMT any colour with arm, 195 mm long with bend of 45 degree with flange (both min wt 80 gms ), complete all as specified and directed.

S&F in repairs 110mm PVC (SWR) WC connector bent type, complete all as specified and directed.

S&F in repairs 75mm dia cast iron nahani trap including jointing to pipe, complete all as specified and directed.

S&F in repairs 15mm bore bib tap, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S&F in repairs 15mm bore stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repairs 15mm bore stop valves, fancy type, chromium plated with long long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges, complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), coloured (excluding fixing bolts, flushing cistern & flush pipe) & including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. and including 'P' or 'S' trap and plastic water closet seat black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinges device & making good to dismantled/damaged floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and directed.

S&F in repair 15 mm bore brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixeds, complete all as specified and directed.

S&F in repair 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210gms), complete all as specified and directed.

S&F in repair 15mm bore pillar tap, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F in repair 15mm bore bib taps of standard PTMT any colour high pressure screwed for iron pipe and fixed (minimum weight 90gms), complete all as specified and directed.

S&F in repair 20mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed, complete all as specified and directed.

110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed.

75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed.

110mm bore dia PVC (SWR) bends, complete all as specified and directed.

75mm bore dia PVC (SWR) bends, complete all as specified and directed.

110mm PVC (SWR) vent cowl complete all as specified and directed.

75mm PVC (SWR) vent cowl complete all as specified and directed.

4mm dia plain mild steel wire, galvanised class 3, in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc., complete all as specified and directed.

15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:3 finished the surface even and smooth without using extra cement, complete all as specified and directed.

Treatment to sunken slab by applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cum per sqm, complete all as specified and directed.

Polythene film, 150 micron thick, laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm, complete all as specified and directed.

100mm thick PCC 1:2:4, type B-1 (using 20mm graded crused stone aggregate) as in padding of sunken slabs to required in desired slope, finished the surface even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed.

Applying 3mm thick wall care putty on wall, complete all as specified and directed.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Preparation of new CGI/PGI steel surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer over a coating of mordant solution including washing the surfaces, complete all as specified and directed.

Preparation of new steel surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash,complete all as specified and directed.

M/S SHEIKH FEROOZ AHMAD

M/S Hilal Builders

M/S Tajamul Ah Buchh

M/S LATIF AHMAD BABA CONSTRUCTION

M/S M.S. BUILDERS

BHAT CONSTRUCTIONS AND BUILFERS