SPECIAL REPAIR AND STRUCTURAL REHABILITATION OF CERTAIN SMQS AT AF STN JAIPUR

Amount

Demolition of Concrete (un reinforced)in ground floor and pavings n exc 15 cm all as specified and directed

M&L Cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) avg. 25 mm thick in levelling course for laying floor finish complete.

Dismantling floor, health or wall tilling and kota stones including cement mortar bedding (bur not backing), removing rubbish off the premises complete all as specified and directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc.0.11 sqm but not exc 0.18 Sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile with and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M & L for glazed ceramic coloured tiles in vertical surfaces 450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with and including rendering 10 mm thick in cement plaster in cement mortar 1:4 on fair faces of brick work or concrete surfaces for backing coat of tiles complete all as specified and directed.

M&L for light shade Ceramic tiles 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exc 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile with and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for light shade Ceramic tiles 7 to 8 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile with and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for 20 mm thick granite stone slab (table rubbed and polished) as on shelves/cooking plateform/pillars over and including screed bed 20 mm thick in cm (1:4) set jointed in neat cement slurry and pointed in white/coloured cement to match the shade complete all as specified and directed.

Taking down Chowkatts or frames n exc 1.5 sq m each with shutters (without taking off shutters form the frames) complete all as specified and directed

Taking down Chowkatts or frames exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames) complete all as specified and directed

S & F solid PVC door frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5mm thick wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet , mitre cut at two corners and joined with two Nos of 150mm long brackets of 15mm x 15mm MS square tube. The two vertical door profiles are to be reinforced with 19mm x 19mm MS square tube of 19 gauge, EPDM rubber gasket and weather seal to be provided through out the frame. The door frame shall be fixed to the wall using 65/100mm long MS screws through the frame using PVC fasteners. Aluminum of four Nos of screws to be provided for each vertical member and miniumum of two nos of screws for each horizontal member complete as per Manufacturer’s specification and drawing and as directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style consisting of frame made out of MS tubes for top & bottom rails.MS frame shall be covered with heat moulded wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900) used instead of exposed portion of PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing as mentioned on Page 149 of SSR-2020 Part-II, complete.

S&F 35 mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides.

S&F 35 mm thick 2nd class HW, glazed and skeleton shutters, open rebated & prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass,gauze etc complete all as specified and directed.

S&F stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 0.63mm and fixed with tinned teaks galvanised wire staples fixed all as specified

S&F 100 mm size type B-21 Mild steel butt hinges fixed complete all as specified and directed.

S&F Aluminium anodised handles fabricated type 125 mm long complete.

S&F Aluminium anodised barrel tower bolt 125 mm size complete.

S&F Aluminium anodised handle, fabricated type each 150 mm long complete.

S&F Aluminium anodised barrel tower bolts, with bolt and fixed, 150 mm size complete.

S&F Stainless steel sliding door bolts, size 300 mm , with bright bolt not less than 12mm dia with and including a minimum of 6 bolt sand nuts, four on bolt plate and two on staple plate and fixed

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, 150 mm long fixed in floor complete

M&L preparing new steel surfaces over 10 cm in width or girth of any description and applying two coat of synthetic enamel paint over and including a coat of red oxide primer complete.

M&L preparing old steel surfaces over 10 cm in width or girth of any description and applying one coat of synthetic enamel paint complete.

M&L preparation of new wooden surfaces of any description, 10 cm in width or girth and applying two coats synthetic enamel paint over and including a coat of pink primer complete.

S & F of aluminium anodised powder coated of approved colour, sliding type three track (02 glazed shutters and 01 gauzed shutter) window with sliding shutter and frame with and including aluminium grill, 5 mm thick glass and mosquito proofing net as detailed below complete all as specified and directed: - (i) Frame section of size 91.85 X 31.75 X 0.88 mm for top and sides rails and 92 X 31.75 X 1.1 mm for bottom rail. (ii) Top, bottom and side rails of shutter of section size 40 X 18 X 1.09 mm. (iii) Glass 5.00 mm thick one side reflective glass and other side visible fixed with rubber gasket and appropriate size aluminium clips and necessary handles, tower bolt etc. as directed. (iv) Stainless steel wire cloth (v) Filling of gap between wall and aluminium frame with silicon putty to make it proper water tight. (vi) Locking arrangement and providing Namda rope to make the frames air tight.

S&F aluminium powder coated partition with two track window including aluminum frame, including powder coated aluminium grill and rubber bead joining cleat for fixing in position, concealed type lock for two shutter, PVC roller including 25x3mm aluminum flat all round window frame for fixing of wire gauge with stainless steel wire cloth 0.36 mm noimnal dia of wire and average width of aperture 0.63 mm on outer frame on side complete etc all as specifed below:- (a) frame (top & side) section shall of size 92.00x31.75x0.88mm (b) frame (bottom) section shall of size 92.00x31.75x1.10mm (c) Top, bottom & side members of shutters section shall be of size 40x18x1.09mm

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows, ventilators, fixed/openable (Top hung/side hung) including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for seperately) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS-733 and IS-1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junction i.e at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/peneling, CP brass/stainless screws all complete as per architectural drawings and the direction of Engineer-in-Charge.

S&F anodized aluminium grill (anodized tranparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws @200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requiremenmt and direction of Engineer-in-charge.

S&F 19 mm thick both side pre laminated particle board (medium density) commercial type fixed to wooden frame / shelf complete all as specified and directed.

Supply and fixing 2nd class hard wood in scantling clean sawn, timber framed fixed in any position as framed work with nails and including dismantaling all as specifed

S&F 2nd class hard wood Plain fillets exc 6 sqcm but not exc 13 sq. cm bull nosed, splayed,chamfered or rounded on one edge or face complete all as specified and directed.

S & F of 30 mm wide flap when open, mild steel bright finish or electro galvanised continuous (Piano) hinge complete all as specified and directed.

S&F Stainless steel Hasp & staple safety type stove enameled black including bolt to hinge plate and fixed with with screws 75 mm in size.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass polished, bright finished

S & F in repairs vitreous china wash basin white, flat back or angle back type, size 550 X 400 mm excluding taps, chain and plug but including waste pipe, brackets, cutting for and pinning in as required complete all as specified and directed.

S&F in repair mixer Pillar taps 15mm bore fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S & F Tubular towel rail, brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flange complete all as specified and directed.

S & F 32mm cromium plated cast copper alloy waste coupling (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms) for wash hand basin all complete ad as directed

S&F 15mm CP stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair

S & F in repair vitreous china wash down water closet pan (Pedestal pattern) white EWC floor mounted hung type with PVC seat cover including fixing bolts and making connection to flushing cistern, including 100mm dia trap etc. complete all as specified and directed.

S&F Flush pipe of polyethylene of low or high density of PVC, 32 mm dia and 80 cm long, for low level flushing cistern complete all as specified and directed.

M&L low level flushing cistern 10 Ltr capacity white complete with inlet ball valve float , syphon assembly and dual flush button and brackets etc. complete.

S&F health faucet (ABS Body) cast copper alloy chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hooks including making connections and fixed in position complete in all respect as specified and directed.

S/F in repairs 15 mm two-way bore bib taps chromium plated cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store in 15mm bore.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store in 20 mm bore.

M&L refixing old steel tubing and connections in new or old position ( walls, ceiling, floors etc ) in 15mm size

M&L refixing old steel tubing and connections in new or old position ( walls, ceiling, floors etc ) in 20mm size

S & F of 15 mm bore steel water tubing medium grade galvanised with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.

S & F of 20 mm bore steel water tubing medium grade galvanised with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.

S&F PVC connection pipe 15mm size with PTMT nuts of length 450mm etc all as specified.

S&F in repairs 15mm bore bib taps fancy type cast copper alloy CP with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F Brass CP mixer 15 mm bore for mixing hot & cold water screwed down for iron pipe including provision for head and hand shower including and fixed complete all as directed

S & F in repairs Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to 15mm dia steel pipe or union all complete as directed

S & F in repair stainless steel Soap dish, approximate size 160x 160x90mm any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed by Engr-in-Charge

S&F in repair grating 100 mm dia stainless steel (Min Wt 25 gms) complete all as specified and as directed.

M&L PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

S&F Cast iron floor trap 75 mm , with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F Cast iron soil, waste and vent spun pipes 75mm , in any length with or without ears with cement joints, laid in trenches or in floors all as directed and specified.

S&F Cast iron soil, waste and vent spun pipes 100mm , in any length with or without ears with cement joints, laid in trenches or in floors all as specified and directed.

S&F in repair cast iron soil, waste and vent spun pipes 100 mm bore in any length with or without ears with cement joints fixed to walls all as specified and directed.

S&F in repair cast iron soil, waste and vent spun pipes 75 mm bore in any length with or without ears with cement joints fixed to walls all as specified and directed.

S&F in repairs spun cast iron 100mm bore bends etc all as specified

S&F in repairs spun cast iron 75mm bore bends etc all as specified

S&F 75 mm Cast iron Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches all as specified and directed.

S&F 100 mm Cast iron Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches

S&F 75 mm Cast iron cowls all as specified and directed.

S&F 100 mm Cast iron cowls all as specified and directed.

S&F stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof for 100mm dia pipe etc all as specified and directed.

S&F stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof for 75mm dia pipe etc all as specified and directed.

M&L for Dismantling water tanks Exc 250 & n exc 500 ltrs capacity and removing from site complete all as specified and as directed.

S&F 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layer white in colour hoisted and fixed in position over 100mm thick PCC (1:2:4) using type Bq, 20mm graded stone aggregate in tank platform all as specified in SSR Part I.

M&L Ball valves 20 mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms/ 50mm-1240 gms) all as specified and directed.

S & f in repair 20 mm bore size Stop valves, cast copper alloy chromium plated screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm with flush pipe complete all as specified and directed.

S & F Stainless steel plate rack of size 30 x 24 inches of approved make as per sample kept in AGE (I) offfice as specified.

Demolition of existing roof treatment, any thickness, including plastering and padding including APP membrane/tarfelt etc complete all as specified and directed.

M & L for plain cement concrete type B-0 1:2:4,mix (using 12.5 mm graded stone agg) as in coping, parapets, bed plates, kerb and the like rounded or chamfered on edges complete all as apecified and directed.

M & L for cutting out cracks to V-section in existing roof, chajjas, terracing or any similar position upto 40 mm deep, cleaning out the same with water jets to get rid of any loose material, wetting, grouting with cement and sand slurry 1:3 mixed with liquid water proofing compound complete all as specified and directed.

M&L for providing, 40 mm thick (average) plain cement concret, type- B0, 1:2:4 (using 12.5 mm graded stone aggregate as in roof pading, concrete finish even and smooth with using extra cement and using liequied WPC as directed by Engr-in-Charge complete all as specified and directed.

S & F APP based polymeric membrane of minimum weighing 3kg/sqm and minimum 3 mm thick reinforced with polyester non wave fabric (weight not less than 150 gms/sqm) laid on primed surface forced application over and including a coat of bituminous primer @ 0.30 ltrs/sqm cpmplete all as specified and directed.

Supply only liquid water proofing compound.

M & L for preparation of APP membrane surface as in roof treatment and applying two coats of bitumen based aluminium paint and all as specified and directed.

Taking down cement plastering on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L 10 mm thick rendering on other than fair faces of brick work in CM 1:6 as inner layer and 5 mm thick rendering in CM 1:4 finish even and smooth (without using extra cement) mixed with liequid WPC as per directed by Engr-in-Charge on external surfaces all as specified and directed. Note : WPC will be measured and paid seperately against respective item.

M & F for rendering 15 mm thick in cement plaster in CM (1:6) on fair faces of brick work or concrete surfaces complete all as specified and directed.

M&L 10 mm thick rendering in CM 1:3 on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for complete removal of existing treatment on ceiling and preparation of old plastered surface of ceiling and applying two coats of oil emulsion distemper over and including 2 mm thick wall care putty and one coat of primer complete all as specified and directed.

M&L for preparation of new plastered surface of ceiling and applying two coats of oil emulsion distemper, 2 mm thick wall care putty and one coat of primer complete all as specified and directed.

M&L for preparation of new plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for preparation of newly plastered previously untreated surfaces of walls and applying two coats of distemper oil emulsion over and including a coat of average 2 mm thick wall care putty and one coat of primer complete all as specified and directed.

M & L for complete removal of existing treatment on wall and applying 2 mm thick water proofing wall care putty, one coat of primer and two coats of distemper oil emulsion complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying 2 mm thick water proofing wall care putty and applying two coats of 100% premium acylic exterior emulsion paint having VOC less than 50 gms/litre and UV resistance as per IS 15489:2004, alkaly & fungal registance, dirt resistance exteriour paint of required shade (company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new surfaces complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over and including alkali resistant primer complete all as specified and directed.

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete.

M & L brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) all as specified and directed.

Brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in 1:4 cement mortar all as specified and directed.

S&F in rep 25 mm dia Stainless steel curtain rod with fixing brackets , stops, side fancy rollers ets complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

S & F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing confirming toFe 410-W (Gde E- 250) quality A. complete.

S&F welded steel wire fabric weight n.exc 4 Kg per square metre complete to wood or steel members.

M&L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strenght of 550 Mpa as in roof coverng/cladding to wall, fixed with self tapping screws as specified.

Providing & fixing false ceiling with fully perforated 12 mm thick micro tegular eged or 10 mm thic square edgd GRG false ceiling all heights with GRG (Glass fibre reinforced Gypsum) false ceiling tiles of size 595 x 595 of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO 0.5 to 0.75 as per IS 8225 : 1987, Noncombustible (Fire resistant/retardant) as per BS-476 (Part4)-1970, fire resistant/retardant and light relectance of 85% (minimum) to be laid in true horizontal level suspended on and including interlocking metal T-Grid of hot dipped galvanized iron section 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main 'T' runners of size 15 x 32 mm of length 3000 mm, cross-T of size 15 x 32 mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per Sqm) i.e 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully thread hanger rod upto 1000 mm length and L-shape level adjuster of size 85 x 25 x 2 mm, galvanized iron parimeter wall angle of size 24 x 24 x 0.40 mm of length 3000 mm to fixed on periphery wall/partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawings and as per directions of Engineer-in-Charge.

M&L for 75 mm thick plain cement concrete type C-2, 1:3:6, using 40 mm graded stone aggregate as in plinth protection or similar work, concrete finish even and smooth with using extra cement complete all as specified and directed.

M&L for 75 mm thick plain cement concrete type D-2, 1:4:8, using 40 mm graded stone aggregate for sub base complete all as specified and directed.

M&L for chequered cement concrete tiles glossy finish 30cmx30cmx25 mm thick, with coloured cement and pigment, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed in CM 1:6 all as specified and directed.

Taking down of aluminium windows with frame and re-fixing in same opening after necessary repairs of cill/jambs etc complete all as specified and directed.

Demolition of cement concrete (reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete.

M & L for MS props erecting for temporary supports to the structural members like beams, slabs etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work as per the instruction of engineer in-charge. These supports shall be provided either in the form of props or trestles fabricated using structural steel as per the site requirements.

M & L for Chipping of slab/columns/beams/chajjas/parapet /roof projection/balcony/staircase and removing loose mortar with chisel hammer without much impact on concrete surface, clean the surface by sand blasting the surface using river sand with minimum of 6 kg pressure at the nozzle or air blow by electric pressure blower by mechanical compressor, cleaning the exposed reinforcement with wire brushes etc and disposal of debris for all lead and lifts, all complete all as specified and directed.

M & L for Cleaning & applying rust remover in two coats over rusted reinforcement surface and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 6-8 sq. mtr/ltr not less than 50 microns dft with Sika friazinc R or equivalent to reinforcement surface as per manufacturer’s instructions including all scaffolding , machinery, tools tackles and clearing of debris. Make: Equivalent of M/s Sika India Pvt Ltd/ Fosroc/Chemsol/Bostik/Choksey etc complete all as specified and directed.

M & L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Note : Additional Reinforcement: Check the diameter of the existing rebars and if the diameter is less than 30% of the original diameter, provide additional reinforcement. Cut 12mm dia bars as main reinforcement to the required length with proper development length. Tie them to the prefixed shear connectors so that the additional rebar acts monolithically with the existing ones and core concrete.

M & L for Shear Connectors by drilling 12mm dia holes up to a depth of 75mm maximum and fixing 8mm dia 'L' shaped anchor rods as shear connectors at every 300mm c/c on the surfaces of the columns/beams or any other structural member as the case may be. Clean the same using air or blower and make sure that there are no fine particles present in the hole and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy- acrylate fixing and anchoring compound. At this stage push the shear connector gently in to the hole and finish the excess resin which comes out of the hole and allow the shear connectors not to be disturbed for Minimum 20 minutes. Make: M/s Sika India Pvt Ltd/ Fosroc/Chemsol/Bostik/Choksey

S & F of new steel or rebars by drilling holes with 10 mm to 20mm dia and 100 to 200mm deep as per IS code of 10D formula and filling the holes after inserting of reinforcement dia 8 to 16mm for anchoring at ends/shear connector and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy- acrylate fixing and anchoring compound ( having the technical parameters mentioned in material specifications) using standard sealant applicator gun after drilling holes of required diameter at required locations, for holding / fixing / placing in position the steel mesh reinforcement at desired level/ stretching. (Note : Steel/reinforcement shall be paid and measured separately). Make: M/s Sika India Pvt Ltd/ Fosroc/Chemsol/Bostik/Choksey

M&L for applying to the damaged concrete portion of slab/ columns/ beams/ chajjas/ parapet / roof projection/ balcony/ staircase with single component, fiber reinforced, dual shrinkage- compensated thixotropic, cementitious patch repair mortar Sika monotop 122F (having the technical parameters mentioned in material specifications) or its equivalent capable of applying up to 20-25mm thick in double layer initially by hand and finishing with troweled carefully compacting the same around the rebar and finishing to bring it in line with existing concrete surface with an average specified thickness and Make: Make: M/s Sika India Pvt Ltd/ Fosroc/Chemsol/Bostik/Choksey

M & L for applying bond coat on the prepared old surface of concrete/masonry to receive new polymer mortar/polymer modified mortar or micro concrete with two coats of Latex Super SBR as per manufacturer specifications. Laying of reinstatement polymer mortar or micro concrete shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concreteMake: M/s Sika India Pvt Ltd/ Fosroc/Chemsol/Bostik/Choksey Note :- (i) From serial No. 112 to 119 are applicable for the structural rapair and strengthening and rehabilitation and roof treatment shall be applied by the company’s authorized applicator firm only. (ii) Contractor have to get prior approval of applicator or authorized agency by submitting its authorization letter to this office for approval prior to commencement of work. Department will conduct an official varification from manufacturer of its authorised agency. (iii) Submission of 10 year warranty certificate for structural repair and waterproofing treatment work over roof is mandatory after completion of work. (iv) The cost of Scaffolding work required at certain places is including in the respective items catered for repairs itself. No extra amount shall be paid for the same.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc, removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

Disconnecting unserviceable sub main wiring/service connection of any size and including steel conduit and accessories and removing from site and making good the disturbed surfaces complete all as specified and directed.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including PVC Conduit complete with all PVC accessories such as socket, elbow, junction box, etc./ fittings ISI marked and sunk type pressed steel terminal switch box 1.6 mm thick with bakelite laminated sheet top cover 3mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed for:- Note: Cutting chases for conduits and sinking's for boxes and making good to walls, floors etc. deemed to be included in quoted rates (a) One light point/bell point controlled by one, one way switch.

(b) One ceiling fan/exhaust fan point controlled by one, one way switch through regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One 3 pin 5 Amp socket on independent board.

(e) One light point controlled by two Nos two switch.

All as per item No. 123 (d) here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed. Note: Cutting chases for conduits and sinking's for boxes and making good to walls, floors etc. deemed to be included in quoted rates

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6.00 Sqmm LT, 1100 volts grade, drawn through and including PVC Conduit with accessories such as socket, elbow, junction box, etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor with suitable lugs made of copper connected to earth dolly complete all as specified and directed. Note: Cutting chases for conduits and sinking's for boxes and making good to walls, floors etc. deemed to be included in quoted rates

S&F switch piano flush type 5 amps, single pole one way 240 volts complete all as specified and directed.

S&F switch piano flush type 15 amps, single pole one way 240 volts complete all as specified and directed.

S&F switch piano flush type 5 amps, single pole two way 240 volts complete all as specified and directed.

S&F bell push piano flush type 5 Amp complete all as specified and directed.

S&F Socket outlet 3 Pin 5/6 Amp flush type complete all as specified & directed.

S&F socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type ISI marked complete all, as specified & directed.

S&F ceiling fan regulator electronic flush , steped (four step) 230 Volts AC all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified.

S&F bell ding dong type AC 230 volt complete all as specified and directed.

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

S&F of LED lamp 9/11 watt complete all as specified and directed.

Supply and fixing LED light fitting 20W, 220V,AC with driver,including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting 10W, 220V,AC with driver,including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED Bldg security light high pressure die cast aluminium housing, IP 66, 25Watt, PF>0.95, Operating Voltage 120-270V AC, 50HZ including hot diped galvanised mounting bracket made to shape with and includinggalvanised clamps with bolts, nuts, washers and conductor to fitting with 3 core 1 sqmm PVC insulated copper cable from control box to fitting complete all as spd.complete all as spd and directed by Engineer-in-Charge.

Disconnecting and taking down existing electric meter and refixing the same electric meter, connecting, testing and sealing properly and making good disturbed surface of walls etc complete all as specified and directed.

Taking down existing Ceiling/Exhaust fan, dismantling blades and refixing after cleaning incl conecting up with three core flexible cable from ceiling rose to fan complete all as specified and directed.

S&F SPN DB Box, 12 way 12 Module, Double door, IP 54, Suitable for flush mounting and surface mounting with 100A Copper bus bar and fully shrouded neutral bar with door earthing and cable entry cover complete all as spd by Engr in Charge.

S&F VTPN DB Box, 4 way 4Module, Double door, IP 54, Suitable for flush mounting and surface mounting with 100A Copper bus bar and fully shrouded neutral bar with door earthing and cable entry cover complete all as spd by Engr in Charge.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP SP , in the MCB DB Complete with connection testing and commissioning

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 20 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of SPN and current carrying capacity SPN 40 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning of TPN 40Amps -100 Amps

Taking down of Geyser of any capacity, cleaning the tank and refixing on wall complete all as spd and directed

M&L for Submain wiring with (2x4.0 sq. mm +1x2.5 sq. mm) FR PVC insulated unsheathed multistranded copper conductor 1100 volts grade cable drawn through and including PVC casing caping ISI marked accessories and one run of 4 sqm single core PVC insulated but unsheathed multistranded copper conductor 1100 volts grade cable as earth conductor all as specified and directed Note : All runs of cables and 1 run of conduit shall be measured and paid as one meter length of unit. Note: Cutting chases for conduits and sinking's for boxes and making good to walls, floors etc. deemed to be included in quoted rates

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole MCB, 20 Amp complete all as specified and directed. (For AC and Geyser)

M&L earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2020 incl dismantling of old unseviceable existing earthing complete all as specified and directed.

Taking up or down steel tubing, 20 mm dia and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Supply and fix GI tubing, 20 mm dia, medium grade, any length ISI marked with all fittings and fixed complete to walls and ceilings or laid in trenches/under road complete all as specified and directed.

Supply and fix in repair Gun-metal, globe, or gate valves, 20 mm dia, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply, installation indoor type, factory made, CPRI approved wall mounting, dust and vermin proof cubical type, LT panel meter box of size 400mm X 400mm fabricated from 2 mm thick (minimum) CRCA sheet with anti corrosive coating and finally epoxy polyester powder coating of flint Grey shade (RAL-7032), suitable arrangement for mounting of 3 electric meter complete all as spd and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

M&L for cutting circular hole 3" in stone wall approx 18" by core cutting machine for installation of split AC pipes complete all as spd and directed.

boon construction company (BID ID -3164141)