Construction of CISF Barracks inside Kamarajar Port

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and whereever required and as directed by Engineer-In-Charge and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15cm deep whereever required and as directed by Enginner-In-Charge and disposal of rubbish lead upto 50m and lift upto 1.5m and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Earth work excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) where ever required including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed by Engineer-In-Charge within a lead of 50 m and as directed by Engineer-In-Charge including all labour, tools etc., all complete

Filling available excavated earth ( excluding rock ) in trenches, plinth, sides of foundations and where ever required etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.50m all complete.

Supplying and Filling in plinth with available sand inside the Port and under floors including,watering, ramming consolidating and dressing where ever required including all labour, material,fuel,tools, transport etc. complete.

Supplying and Filling of carted good earth in plinth for road, interlocking tiles and pathways and where ever required as directed by the Engineer- In charge and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level with CC 1:4:8 (1 Cement :4 coarse sand :8 graded stone agregate 40 mm nominal size) for OHT, Substation, compound wall etc., and wherever required as directed by the Engineer-in-charge and as per drawing and specification etc., all complete

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level with CC 1.4.8 (1 Cement :4 coarse sand :8 graded stone agregate 40 mm nominal size) as per drawing and specification etc., and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1Cement : 3 coarse sand), including the cost of required centering, shuttering complete with CC 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) whereever required as per drawing and specification all complete

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm diameter holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor. With Chlorpyriphos EC 20% with 1% concentration where ever required as and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and urability as per direction of Engineer-in-charge. , all complete (Note :- Minimum Cement content considered in this item is @ 330 kg/cum) as per drawing ans specification where ever required and as directed by Engineer-In-Charge.

All works upto plinth level

All works above plinth level upto V floor

Providing and laying in position machine batched and machine mixed design M-20 grade reinforced cement concrete work excluding cost of centering , shuttering etc., where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete.

All works upto plinth level

All works above plinth level upto V floor

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. as directed by the Engineer-In-charge all complete and including its removal at all levels, for and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall

Beams, lintels, cantilevers & wallsmoulded chamber burnt bricks with including cost

Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ)

Spiral staircases (including landing)

Arches, Domes vaults upto 6m span

Columns, Pillars, Piers, Abutments, posts and struts

Providing Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundations and plinth in Cement mortar 1:6 (1 cement: 6 coarse sand ) as per drawing and whereever required etc.,and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundations and plinth in Cement mortar 1:4 (1 cement: 4 coarse sand ) for guard room as per drawing and where ever required etc. and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V in Cement mortar 1:6 (1 cement: 6 coarse sand ) as per drawing and where ever required etc., and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size) as per drawing etc., and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg. per square metre on damp oroof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil as per drawing etc., and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water -proofing compound confirming to IS 2645 including cleaning the surface before treatment, (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabsand as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete (c) After two days of proper curing applying a secound coat of cement slurry admixed with proprietary water proofing compound conforming to IS : 2645. Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test, All above operations to be done in order and as directed and and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete With average thickness of 120 mm and minimum thickness at khurras point

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shuttersand as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (single leaf)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete 30 mm thick including stainless steel butt hinges wirh necessary screws (single leaf)

Providing and fixing ISI marked shutters for Cup board conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete. 25 mm thick (for Cup board) including ISI marked nickel plated bright finished M.S piano hinges with necessary screws

Providing and fixing 1mm thick M.S. sheet sliding shutter with frame and diagnal braces of of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, 25mm dia. pully , 40x40x6 mm angle and T-Iron guide at the top , bottom respectively including applying primet and all necessary fittings complete for substation building and where ever required etc.and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing single rebate door frame fabricated from sections roll formed out of 1.2mm thick galvanized steel (Base steel as per IS 513) with zinc of 120 gms/sq.mtr where ever required all complete. The overall size of the section should be 80x50mm and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 10.13.1 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). for substation and where ever required etc., all complete.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). for substation and where ever required etc.,and as directed by Engineer-In-Charge including all labour, materials ,tools etc., and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding and where ever required as directed by the Enginner -In charge.and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing steel work welded in bulit up sections/framed work including cutting , hoisting, fixing in position and applying priming coat of approved steel primer using structural steel in stingers, treads, landings etc. of statir case including use of required plates wherever required all complete For over head tank and where ever required as directed by the Engineer-In charge and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete M.S Hot finished welded type tubes for CISF Store, Fish Market , Vegetable market and where ever required as directed by the Enginner-In charge.

Supplying and fixing MS 150MM dia. Casing pipe including fittings and accessories at Fish / Vegetable market and where ever required as directed by the Engineer - In charge. and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing & fixing window and Ventilator fabricated from roll formed sections made of glavinazed steel colour coated/powder coated (Base steel as per IS 513"D",glavinized asper IS 277with zinc of 120gm/ Sqm ) with total coated thicknessof 0.60mm of Eco 4000 series (Double rebate) including 5mm glass, grill, mosquito mesh, fixed louvers & with all accessories. (NCL Seccolor make or equivalent) and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete Eco 4000 Series Openable window/Ventilator

Supplying and providing Reinforcement for R.C.C. work using Thermo-Mechanically Treated bars (FE-500) including straightening, cutting, bending, placing in position and binding and tying with 1.25 mm dia black annealed steel binding wire as per drawing and releveant IS all as directed by Engineer-In-Charge including all labour, materials ,tools etc., and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete.

Providing Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement, 18 mm thick at substation and where ever required as directed by the Engineer-Incharge and as directed by Engineer-In-Charge including all labour, materials ,tools etc., and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and making 12mm thick cement plaster of mix: In Cement Mortar 1:4 (1 cement : 4 fine sand) for internal wall surfaces as per specification and drawing where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools, scaffolding, etc., all complete

Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix: In Cement Mortar 1:4 (1 cement : 4 fine sand) for external wall surfaces as per specification and drawing where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools, scaffolding, etc., all complete

Providing and making 6 - 10mm thick cement plaster of mix In Cement mortar 1:3 (1 cement : 3 fine sand) as per specification and drawing where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools, scaffolding, etc., all complete

Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden batten nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge. (15 mm wide and 15 mm deep groove )and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing plaster drip course/groove in plastered surface or moulding to R.C.C projections as per direction of Engineer-In charge and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-incharge at substation and where ever required .(payment for providing grooves shall be made separately and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Supplying and laying Interlocking 60mm thick paver block of M30 grade in position as approved over jamuna sand of average 50mm thickness including filling the gaps with existing sand as per direction of Engineer-in - charge at site for parking area of Multi gym and whereever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Supplying and laying in position 80mm thick paver blocks of M30 grade of design as approved over existing sand of average 50mm thickness including filling the gaps with jamuna sand complete whereever required as per direction of Engineer-in - charge at site and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Supplying and providing Interlocking tiles in court yard of substation and where ever required as directed by the Engineer- In charge all complete and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth at substation building and where ever required as directed by the Engineer-In charge and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand) at substation building and where ever required as directed by the Engineer -In charge all complete and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Supplying and providing Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of G.I barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete at substaion building and where ever required (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used.

Providing Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete as per drawing and specification( 40 mm thick with 20 mm nominal size stone aggregate)

Providing and fixing glass strips in joints of terrazo/ cement concrete floors at substation building as per direction of the Enginner-In charge. (40mm wide and 4mm thick)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in flooring , over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. all complete, where ever required as directed by the Enginner- In charge. (Size of Tile 600 x 600 mm) and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved brand and manufaturer , in all colours & shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) confirming to IS 15477 , in average 6mm thickness, including grouting of joints where ever required as directed by the Enginner- In charge all complete.(Size of Tile 600 x 600 mm) and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing Kota stone / Eurocon tile flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand ) where ever required as directed by the Enginee - In Charge. (20 to 25 mm thick) and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing Kota stone / Eurocon tile 20 mm (average ) thick in risers and treads of steps skirting dado and pillars laid on 12mm (average thick cement morter 1:3 (1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness sqm 799.40 to be specified by the manufacturer) of Ist quality for wall dadoing conforming to IS :15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown, laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Applying priming coat with ready mixed red oxide zinc chromate primer including second coat of approved brand and manufacture on steel galvanised iron/steel works where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Applying priming coat with ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Applying wall painting with acrylic emulsion paint having VOC(Volatile organic compund ) content less than 50grams/litre of approved brand two coat on new steel surface of Over Head Tank/substation and where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Applying wall painting with synthetic enamal paint having VOC(Volatile organic compund ) content less than 150grams/litre of approved brand two coats on new steel surface in Over head tank and where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Applying wall painting with premium acrylic emulsion paint of interior grade having VOC(Volatile organic compund ) content less than 50grams/litre of approved brand one coats on new steel surface in substation and where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Painting new wood surface with ready mixed pink or grey primer of approved brand and manufature on wood work( Hard and soft wood) and where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Painting new wood surface synthetic enamel paint of approved brand and manufature to give an even shade two coat where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Painting exterior surface with TEXTURED exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with: On new work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications. Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture where ever required as directed by the Engineer - In charge all complete.

Distempering with dry distemper of approved brand and manufacture (two or more coats ) and of required shade on new work , over and including priming coat of whiting to give an even shade where ever required as directed by the Engineer - In charge all complete.

Providing and applying white washing with lime even shade three coats in wall surface of substation building and where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

"Providing and applying ready mixed (oil bound washable distemper / Acrylic distemper) of approved manufacturer of required shade of 2 (two) coats over one coat of primer wherever required and as directed by the Engineer-in-charge including all labour, material, tools, scaffolding, etc. Complete.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc.complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):(With float glass panes of 4.0 mm thickness) where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws etc. complete:(250 x 16mm) where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ),transparent or dyed to required colour or shade, with necessary screws etc. complete: (200x10 mm) where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing bright finished brass handles with screws etc. complete: (125mm) where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing bright finished brass door latch with necessary screws etc. complete: (250x16x5mm) where ever requiredand as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete, (250x16mm )for substation and where ever requiredand as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete, 200x10mm for substation and where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete , 100mm for substation and where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape as indicated in the drawing and wherever required. ( 1.00 mm thick with zinc coating not less than 275 gm/m² ) and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides , ball bearing and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. (80x1.25mm MS lath with 1.25mm thick top cover) where ever requiredand as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) /Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) for Boundary wall and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

PLAY COURT

Supplying and filling clay mixed with soil for Vollyball/Basket ball/Badminton court all as per drawing and specification as per drawing and as directed by Engineer-in -charge at site including all labour , material, transportation, equipment , fuel etc., complete

Providing and laying in position cement concrete 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size) excluding the cost of ntering and shuttering up to plinth level as per drawing and specification and where ever required and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and laying in position bitumen hot sealing compound for expansion joints using grade ‘A’ sealing compound in Basket ball /Badminton court all as per drawing and specification and as directed by Engineer-in -charge at site including all labour , material, transportation, equipment , fuel etc., complete

Providing grit filling in Basket ball /Badminton court all as per drawing and specification and as directed by Engineer-in -charge at site including all labour , material, transportation, equipment , fuel etc., complete

Supplying and fixing M.S Pole as per drawing and specification at Basket/Badminton Court including painting with Synthetic enamel paint with prime coat as directed by Engineer-in -charge at site including all labour , material, transportation, equipment , fuel etc., complete

Road work

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the subgrade and disposal of surplus earthwith lead upto 50 metres and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete all as per drawing and specifications and directions of Engineer-in-Charge.( material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 all complete.

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete all as per drawing and specifications and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and applying prime coat over the WMM surface @ 0.75 Kg / sqm using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing WMM surface as per relevant MoRTH Technical Specification and directions of Engineer-in-Charge all complete.

Providing and applying tack coat over the bitumious surface @ 0.50 Kg / sqm using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing bituminous surface as per relevant MoRTH Technical Specification and directions of Engineer-in-Charge all complete.

Providing and laying Dense Graded Bituminous Macadam using crushed stone aggregates of specified grading(Grade II), premixed with bituminous binder and filler, ransporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per relevant MORTH Technical Specification and directions of Engineer-in-Charge all complete. (50 mm average compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. )

Providing and laying Bituminous concrete wearing course using crushed stone aggregates (Grade II) of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density , all as per drawing and as per relevent MORTH Technical Specification , complete and as per directions of Engineer-in-Charge all complete. ( 40 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. )

Providing Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 as per drawing and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and stacking of good earth at site as per relevant speciications as directed by Engineer-in -charge including royalty and carriage for all lead ( Earth measured in stacks will be reduced by 20% for payment) and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Site grading by cutting the soil heaps and filling the earth in low level areas mechanically by using excavator and loader /tipper within a lead of 1km all complete. and as directed by Engineer-In-Charge including all labour, tools etc., all complete

Disposing the surplus soil mechanically by using excavator and loader /tipper within a lead of 5km including all complete and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete. Note: 1.The tenderer shall maintain trip sheets in triplicate in KPL approved format at his own cost for the quantity of surplus transported. 2. Payment will be made based on the lorry cubical content. 20% deduction of voids will be made for Suplus earth. 3.However the final quantity will be restricted to (i) actual quantity of Earthwork minus refilling quantity for surplus earth

Supplying, stacking and Spreading 10 mm thick Red Bajri/ Gravel, watering and rolling complete including preparation of the surface and rolling with road roller / hand roller for Parade Ground and wherever required as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level using cement mortar 1:4 (1 cement :4 coarse sand) and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Providing and fixing in position First class country wood (padauk) wrought main frames for door frames with necessary M.S. hold fasts / clamps fixed suitably to the masonry / concrete including cutting pockets and grouting with P.C.C. 1:3:6 (1 cement : 3 coarse river sand : 6 hard granite graded stone aggregate of 20mm nominal size) in volumetric proportions, curing including painting with one coat of boiling coal tar paint on the portions of the timber abutting against masonry / concrete all as shown in the drawing and as directed including cement and all other materials, labour, tools, equipment, etc., complete.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner and as directed by Engineer-In-Charge including all labour, materials ,tools etc., all complete

Description of Work / Item(s)

Amount

Point wiring in PVC conduit, with modular type switch. Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated multistrand copper conductor wires in surface / PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated multistrand copper conductor wires etc. as required (Group C) and as per technical specification and as per latest IS / IEC

Twin control point wiring in PVC conduit, with modular type switch Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated multistrand copper conductor wires in surface / PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated multistrand copper conductor wires etc. as required and as per technical specification and as per latest IS / IEC

Circuit/ submain wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated multistrand copper conductor wires in surface/ recessed PVC onduit as required and as per technical specification and as per latest IS / IEC

2 x 1.5 sq. mm + 1 x 1.5 sq mm earth wire

2 x 2.5 sq. mm + 1 x 2.5 sq mm earth wire

2 x 4 sq. mm + 1 x 4 sq mm earth wire

2 x 6 sq. mm + 1 x 6 sq mm earth wire

4 x 6 sq. mm + 2 x 6 sq. mm earth wire

4 x 10 sq. mm + 2 x 6 sq. mm earth wire

Supply and drawing of 2 Pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed PVC conduit as required and as per technical specification and as per latest IS / IEC

Supply and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required and as per technical specification and as per latest IS / IEC

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required and as per technical specification and as per latest IS / IEC

Supply and Fixing Power plug Point Modular type accessories: Supply and fixing of metal box of GI box with modular plate and cover in front on surface or in recess , including providing and fixing of 3 pin 5/6 amps. modular socket outlet and 5/6 amps. modular switch, connections, painting etc. as required. (For light plugs) and as per technical specification and as per latest IS / IEC

Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. and as required and as per technical specification and as per latest IS / IEC

Supply & fixing of suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required and as per technical specification and as per latest IS / IEC

Supply and fixing of following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required and as required and as per technical specification and as per latest IS / IEC

15/16 Amp. Switch

3 Pin 5/6 Amp. Socket

Telephone socket outlet

T.V socket outlet

Supply and fixing of following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required

1 or 2 Module (75mmX75mm)

6 Module (200mmX75mm)

Supply and fixing modular type electronic fan regulator: Supplying and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required and as per technical specification and as per latest IS / IEC

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamps of internl dia 150 mm & 73mm in height top laid of 1.5 mm thick MS sheet with its top hanged for proper bonding top lid shall be screwed in cast iron/ MS sheet box by mean of 3.3mm dia round headed screwes one lock at the corners and as per technical specification and as per latest IS / IEC

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, multi stranded copper conductor wires including providing and fixing phenolic laminated sheet cover on the fan box etc. as required and as per technical specification and as per latest IS / IEC

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required and as per technical specification and as per latest IS / IEC

Upto 450 mm sweep

Fixing louvers/ shutters for exhaust fan: Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes and as per technical specification and as per latest IS / IEC

Supply and fixing of following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) and as per technical specification and as per latest IS / IEC

8 way , Double door

Supply and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) and as per technical specification and as per latest IS / IEC

4 way (4+12), Double door, Horizontal type

6 way (4+18), Double door, Horizontal type

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) and as per technical specification and as per latest IS / IEC

8 way (4 + 24), Double door

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A, 16 KA,TPMCCB and as per technical specification and as per latest IS / IEC

Supply and fixing 'C' Series, SP MCB : Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required and as per technical specification and as per latest IS / IEC

Single pole

Double pole

Triple pole

Triple pole and neutral

Supply, installation, testing and commissioning of chemical earth pit inclluding civil work etc as per technical specification and as per latest IS / IEC

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) and as per technical specification and as per latest IS / IEC

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required and as per technical specification and as per latest IS / IEC

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required and as per technical specification and as per latest IS / IEC.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required and as per technical specification and as per latest IS / IEC

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required and as per technical specification and as per latest IS / IEC Internet Socket RJ 45 Cat.

Supplying and fixing 40 A to 63 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required and as per technical specification and as per latest IS / IEC

40Amp./63Amp. FP MCB

Suppling Installation Testing & Commissioning of upto 25W LED Extruded Aluminium batten available in 4ft run length with multiple lumen packages and suitable for Surface, Wall & Conduit mounting (with accessories) and as per technical specification and as per latest IS / IEC

Suppling Installation Testing & Commissioning of 20Watts LED Flicker free, high efficiency and robust industrial batten family suitable for Surface, Wall and Conduit mounting and as per technical specification and as per latest IS / IEC

Suppling Installation Testing & Commissioning of upto 10W LED Extruded Aluminium batten available in 2ft run length suitable for mirror with multiple lumen packages and suitable for Surface, Wall & Conduit mounting (with accessories). as per technical specification and as per latest IS / IEC.

Suppling Installation Testing & Commissioning of upto 8 WATT LED Slim profle surface mounted downlight with options of 700 to 2000 lumen as per technical specification and as per latest IS / IEC

Suppling Installation Testing & Commissioning of upto 12 WATT LED Slim profle surface mounted downlight with options of 700 to 2000 lumen as per technical specification and as per latest IS / IEC.

Suppling Installation Testing & Commissioning of 6 Watts Pressure Die cast housing LED bulkhead with IP66 Protection and IK09 impact resistance suitable for surface and wall mounting applications as per technical specification and as per latest IS / IEC.

Suppling Installation Testing & Commissioning of 25Watts LED Fully diffused recessed Mounted 2'X2' LED luminaire with high transmitive diffuser suitable for indoor spaces as per technical specification and as per latest IS / IEC.

Supplying installation testing and commissioning of upto 12W LED based retro fit bulb and as per technical specification and as per latest IS / IEC.

Supply of 1200 mm sweep size special design energy saving ceiling fans with low power consumtion aluminum motor covers of larger diameters complete with double ball bearings, Aluminium blades, down rod, shackle insulator, canopy but without regulator etc complete as required or equivalent and as per technical specification and as per latest IS / IEC.

Supplying installation testing and commissioning of 450mm Dia Wall mounted fan and as per technical specification and as per latest IS / IEC.

Supplying, installation testing and commissioning of Heavy duty capacitor start single phase ISI marked 300 mm dia Single Phase Industrial duty 4 pole 1400 rpm exhaust fan complete without louver, bird screen etc. and with 3 core flexible wire lead as required and as per technical specification and as per latest IS / IEC.

Supplying , installation testing and commissioning of Heavy duty capacitor start single phase ISI marked 450 mm dia Single Phase Industrial duty 4 pole 1400 rpm exhaust fan complete without louver, bird screen etc. and with 3 core flexible wire lead as required and as per technical specification and as per latest IS / IEC.

Supply Installation Testing and commissioning of krone type 10 Pair Telephone Tag Block and as per technical specification and as per latest IS / IEC.

Supply Installation Testing and commissioning of krone type 20 Pair Telephone Tag Block and as per technical specification and as per latest IS / IEC.

Suppling and laying of High Conductivity Solid Annealed Bare Copper industrial Telephone (Switchboard) Cables with High Density Polyethylene Insulation, Paired, Polyester and Sheathed with High Oxygen Index, Fire Retardant, PVC Compound, Grey Outer Sheath generally conforming ITD Specification and as per technical specification and as per latest IS / IEC.

10 Pair 0.5mm ARMOURED TELEPHONE CABLES

20 Pair 0.5mm ARMOURED TELEPHONE CABLES

Supply Installation Testing and commissioning of 2+4 way TV TP junction box and as per technical specification and as per latest IS / IEC.

Supply Installation testing and commissioning of 15HP star delta starter suitable for aata chakki motor including one number additional 32Amp DP outgoing for light distribution board and as per technical specification and as per latest IS / IEC. Note: Star Delta Starter must be provided as per fuse less type-2 co-ordination.

Description of Work / Item(s)

Amount

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern,with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap with outlet grating and other couplings in C.P. brass,including painting of fittings and cutting and making good the walls and floors wherever required. Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever requireD. White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required. Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :

For 100 mm dia pipe

For 75 mm dia pipe

Providing and fixing soil, waste and vent pipes :

100 mm dia - Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

75 mm diameter - Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe

100 mm dia : SS 304 grade coupling with EPDM rubber gasket

75 mm dia: SS 304 grade coupling with EPDM rubber gasket

Providing and fixing terminal guard :

100 mm: Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Sand cast iron S&S as per IS - 3989

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

100x100x100 mm: Sand cast iron S&S as per IS - 3989

75x75x75 mm: Sand cast iron S&S as per IS - 3989

Providing and fixing single equal plain junction of required degree :

100x100x100 mm: Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

75x75x75 mm: Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing plain bend of required degree.

100 mm dia: Hubless centrifugally cast (spun) iron pipes epoxy coated inside&outsideIS:15905

75 mm dia: Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

100 mm dia: Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

75 mm dia: Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors 100 mm inlet and 100 mm outlet: Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe: 32 mm dia

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern

Providing and fixing in position best indian Health Faucet with 8mm dai 1 meter long Flaxible Tube and wall bracket.CERA..CAT. NUMBER (F8030102)

Providing and fixing in position best indian single Lever Auto mixing Basin Mixer Pop-up (Cartradge Size 32mm,nickel plating 0.10 micron and chrome plating 0.3 micron) For Wash Basin area use only ..CERA CAT.. NUMBER (F2008461)

Providing and fixing in position best indian shower rose 180mm ABS body and face chrome plated,with gray face plate with rubit cleaning system. CERA CAT.. NUMBER (F7020302)

Providing and fixing in position best wall mixture with telephone shower arrangement,connecting legs&wall flanges but without crutch & telephone shower. CERA CAT.. NUMBER (F2008402) .

Providing and fixing (0.3 micron Chrom and 10 micron Nickel plated) Bottle Trap for wash basin and sink / URINAL Bottle Trap (with Internal Partition) 32mm Size with 250mm & 190mm Long Wall Connection Pipes & Wall Flange Also available CERA CAT.. NUMBER (F8060403)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge Internal work - Exposed on wall

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

25 to 40 mm nominal bore

50 to 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

32 mm nominal bore.

40 mm nominal bore

50 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing brass bib cock of approved quality : 15mm nominal bore

Providing and fixing high density polyethylene water storage loft tank of suitable capacity required as per site condition with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.

Description of Work / Item(s)

Amount

Supply, erection, testing & commissioning INDOOR 630 AMPS, 11KV, 4 PANEL HT GEAR with 1 no. of 630AMPS TP VCB and 3 Nos.630 AMPS TP VCB, Copper bus bar with interlock key sytem, earth switch etc as detailed in the Technical Specification and as per latest IS and IEC.

Supply, erection, testing and commissioning of 1 panel, 630Amps ,11 KV, 3 Phase, 50 Hz., metal clad, dead front, 350 MVA rupturing capacity Vacuum Circuit Breaker Incoming / Outgoings , Copper bus bar, earth switch etc. as detailed in the Technical Specification and as per latest IS and IEC.

Supply, erection, testing & commissioning of approved make oil immersed naturally ONAN cooled, double wound, core type outdoor copper wound 400KVA, 11 kV/ 433 Volts, Step Down Transformer of following capacities operating on 3 phase, 50 Hz 4 wire & neutral earthed system continuously rated for a full temperature rise in oil as detailed in the Technical Specification and as per latest IS and IEC.

Supply, erection, testing & commissioning of SILENT (Canopy design) liquid cooled 140KVA DG Set with electronic governer with one Diesel Engine with rated capacity at 0.8 P.F. 1500 RPM, Output MCCB control 4 stroke multi-cylinder coupled to brush less type 415 volts 50 cycle, second self excited alternator completed with cushy pads as detailed in the Technical Specification and as per latest IS and IEC.

Supply, erection, testing & commissioning of Main LT Panel consists of 01 no. of800 Amp 36 KA FP EDO ACB and 1 No 630 Amps 36KA FP EDO ACB as incoming, 01 no. of 400Amps, FP,MCCB, 03 nos. of 315Amps, FP,MCCB, 03 nos. of 100Amps, FP,MCCB, 02 nos. of 63Amps, FP,MCCB and 02 nos. of 32Amps, FP,MCCB as outgoing feeders as detailed in the Technical Specification and as per latest IS and IEC.

Supplying, erection, testing & commissioning of MAIN EMERGENCY Panel consists of 02 nos. of 315 Amp 36 KA FP MCCB as incoming, 01 no. of 400Amps, FP,MCCB for bus coupler, 03 nos. of 315Amps, FP,MCCB and 02 nos. of 100Amps, FP,MCCB as outgoing feeders and panel shall have AMF facility to achieve electrical interlocking, synchronizing, buscoupler switching, auto operation of incommer and bus coupler, auto start of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc., as detailed in the Technical Specification and as per latest IS and IEC.

Supply, erection, testing & commissioning of 200KVAR CAPACITOR PANEL with 12 stepped Automatic Power Factor Correction relay (APFC relay) as detailed in the Technical Specification and as per latest IS and IEC.

Supply, erection, testing & commissioning of AMF PANEL consists of with incoming feeder of 1 No. 315 Amp 36KA FP MCCB and 1 Nos. 315 Amp ATS, 03 nos. of 100Amps, FP,MCCB, 01 no. of 250Amps, FP,MCCB, 05 nos. of 63Amps, FP,MCCB and 02 nos. of 32Amps, FP,MCB as outgoing feeders as detailed in the Technical Specification and as per latest IS and IEC.

Supply, erection, testing & commissioning of outdoor type feeder panel (street light) consists of 01 no. of 100Amps, 10KA, FP,MCCB as incoming and 05 nos. of FP, 63Amps, 10KA MCB and 05 nos. of 40Amps, 10KA, MCB as outgoing with timer control etc as detailed in the Technical Specification and as per latest IS and IEC.

Supply, erection, testing & commissioning of outdoor type feeder panel(External light feeder pillar) consists of 01 no. of 63Amps, 10KA, FP,MCCB as incoming and 05 nos. of FP, 32Amps, 10KA MCB and 01 no. of 50Amps, 10KA, MCB as outgoing with timer control etc as detailed in the Technical Specification and as per latest IS and IEC.

Supplying, erection, testing & commissioning of 3 Mtr Aluminium ornamental pole completely shock proof with inner steel pole, polyster/PU finish paint black including foundation, foundation bolt & nuts , 01 no. of earth pit and other civil works etc. as detailed in the Technical Specification and as per latest IS and IEC.

Supplying, erection, testing & commissioning of 40W LED WINDSOR small ornamental post top, cast/spun aluminium body with PC diffuser in clear finish Cast Aluminium , interconnection from MCB to light fitting etc as detailed in the Technical Specification and as per latest IS and IEC.

Supply , Installation & commissioning of 16 mtr G.I. 20 sided polygonal High mast tower of approved make suitable for fixing 12 nos. of 250Watts LED flood light luminaries including supply of 12 nos. of 250Watts Flood Light Luminaries, 02 nos. of chemical earth pit, 01 no. of feeder pillar, barricade arrangement etc, civil foundation with foundation bolt and nuts etc. as detailed in the Technical Specification and as per latest IS and IEC.

Supply of 3core(P,N,E) X 6 sq. mm Aluminium XLPE LTUG Cable as detailed in the Technical Specification and as per latest IS and IEC.

Supply of 4 core X 6 sq. mm Aluminium XLPE LTUG Cable and as detailed in the Technical Specification and as per latest IS and IEC.

Supply of 4core X 10 sq. mm Aluminium XLPE LTUG Cable and as detailed in the Technical Specification and as per latest IS and IEC.

Supply of 4 core X 16 sq. mm Aluminium XLPE LTUG Cable and as detailed in the Technical Specification and as per latest IS and IEC.

Supply of 4 core X 35 sq. mm Aluminium XLPE LTUG Cable and as detailed in the Technical Specification and as per latest IS and IEC.

Supply of 3½ coreX 95 sq. mm Aluminium XLPE LTUG Cable as detailed in the Technical Specification and as per latest IS and IEC.

Supply of 3½ coreX 150 sq. mm Aluminium XLPE LTUG Cable as detailed in the Technical Specification and as per latest IS and IEC.

Supply of 3½ core X 185 sq. mm Aluminium XLPE LTUG Cable as detailed in the Technical Specification and as per latest IS and IEC.

Supply of 3½ core X 300 sq. mm Aluminium XLPE LTUG Cable as detailed in the Technical Specification and as per latest IS and IEC.

Supply of 3 core X 120 sq. mm Aluminium 11KV, HT XLPE UG cable consists of Insulated, Insulation Screening with extruded Semi Conducting Compound in combination with Copper Tape, cores laid up, innersheath of PVC tape, galvanised flat steel strip armoured and overall PVC Sheathed Cable as detailed in the Technical Specification and as per latest IS and IEC.

Supply , installation, testing and commissioning of chemical Earthing and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as required and as detailed in the Technical Specification and as per latest IS and IEC.

Supply , installation, testing and commissioning of earthing with 600mmX600mmX 3mm Copper plate verticallly for earthing with its top at least 3 meters below ground level complete with 40mm dia G.I. pipeand providing masonry enclosure with cover plate having locking arrangement and watering pipe, alternate layers of characoal/ coke with salt etc as detailed in the Technical Specification and as per latest IS and IEC.

Supply and laying of 6 SWG G.I. wire at 0.50 meter below ground level for conductor earth electrode, including connection/termination with GI thimble etc. as required and as detailed in the Technical Specification and as per latest IS and IEC.

Supply and laying of 25 mm X 5 mm CU. strip at 0.50 metre below ground as strip earth electrode, including Connection/terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm and as detailed in the Technical Specification and as per latest IS and IEC. .

Supply and laying of 25 mm X 5 mm GI strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm and as detailed in the Technical Specification and as per latest IS and IEC.

Supply and laying of 25 mm x 5 mm Copper strip for earth pit as detailed in the Technical Specification and as per latest IS and IEC.

Supply and laying of 25 mm x 5 mm G.I. strip earth pit as detailed in the Technical Specification and as per latest IS and IEC.

Supply and laying of 25 mm X 5 mm copper strip for panels on surface or in recess for connections etc. as detailed in the Technical Specification and as per latest IS and IEC.

Supply and laying of 25 mm X 5 mm G.I. strip for panels on surface or in recess for connections etc. as detailed in the Technical Specification and as per latest IS and IEC.

Supply, erection, testing & commissioning of perforated painted with powder coating M.S. cable trays as per technical specifications and as per latest IS/IEC

100 mm width X 50 mm depth X 1.6 mm thickness as detailed in the Technical Specification and as per latest IS and IEC. .

300 mm width X 50 mm depth X 1.6 mm thickness as detailed in the Technical Specification and as per latest IS and IEC..

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of size Upto 35 sq. mm ,1.1 kV directly in ground including excavation upto depth of 750mm and refilling the trench etc. with bricks (1mtr - 18 Nos. of brick) as detailed in the Technical Specification and as per latest IS and IEC. .

Laying of one number PVC insulated and PVC sheathed , XLPE power cable of 1.1 kV grade with bricks for laying of following size in the existing RCC/ HUME/ METALDWC pipe / dirct ground (bricks 1mtr - 18 Nos) as per technical specifications and as per latest IS/IEC

Upto 35 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing masonry open duct or with bricks as per technical specifications and as per latest IS/IEC

Upto 35 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on cable tray as per technical specifications and as per latest IS/IEC

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and installation of cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3.5 Core and 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV gradecomplete as per technical specifications and as per latest IS/IEC

3 Corex 6 sq.mm

4 coreX 35 sq. mm

3½ core X 95 sq. mm

3½ core X 150 sq. mm

3½ core X 185 sq. mm

3½ core X 300 sq. mm

4 core x 6 Sq. mm.

4 core x 10 Sq. mm.

4 core x 16 Sq. mm.

supply and installation of indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for 3 core, 120Sq.mm XLPE aluminium conductor cable of 11 KV gradeas per technical specifications and as per latest IS/IEC

supply and installation of straight through heat shrinkable jointing kit complete with all accessories including ferrules suitable for 3 core, 120Sq.mm, XLPE aluminium conductor cable of 11 KV grade as per technical specifications and as per latest IS/IEC

Laying of one number PVC insulated and PVC sheathed , XLPE power cable of 3 core * 120Sq.mm,11 KV grade UG cable with RCC druff for direct ground / RCC/HUME/ METAL pipe as per technical specifications and as per latest IS/IEC.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as per technical specifications and as per latest IS/IEC

120 mm dia (OD-120 mm & ID-103 mm nominal)

200 mm dia (OD-200 mm & ID-175 mm nominal)

Co-ordination works with CEIG / CEA for getting safety certificate, approval, preparation of SLD and other drawings etc., for commissioning including supply of required nos. of HT &LT Electrical insultaion mat for all indoor HT & LT panels, danger boards, CO2 fire extinguisher, first aid kit etc. The Statutory payments shall be reimbursed by KPL.

Description of Work / Item(s)

Amount

Rain Water Harvesting

Drilling as per IS:2800-Part(1) (with percusion or combination rig ) from ground level in all kinds of soils including boulders(excluding rock ) with diameter of bore 300mm whereever required including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete upto 90 metre depth below ground level or as directed by the Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in the recharge well to be fixed with required thickness indicated as per standard drawing over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.

Supplying, assembling, lowering and fixing in vertical position in bore well, 200mm dia. nominal size unplasticized PVC medium well casing (CM) pipe with ribs , conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge

Supplying, filling, spreading & leveling pee gravel 50 mm nominal size in the recharge well with the required thickness as per standard drawing for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling stone boulders 100mm nominal size in the recharge well with the required thickness as per standard drawing for all leads & lifts, all complete as per direction of Engineer-in-charge

Providing & fixing of UPVC Pipes,confirming to ASTM standard including all UPVC fittings like tees, elbows, bends, unions, coupling, reducer tees, collars etc. The work shall include cutting jointing with solvent cement pressure testing the joints / pipeline for 7 kg/sq.cm

Supplying and Fixing of UPVC Pipes 20mm dia

Supplying and Fixing of UPVC Pipes 25mm dia

Supplying and Fixing of UPVC Pipes 32mm dia

Supplying and Fixing of UPVC Pipes 40mm dia

Providing, fixing testing and commissioning of UPVC Ball Valve 50MM Dia including unions etc., Complete

Providing, fixing, testing and commissioning of brass`Y' / pot 50mm Dia Stainer screw type tested to 20 kg / sqmm

Supplying and Fixing CPVC Pipes of 32 mm dia (SDR-11) For Hot water

Supplying and fixing gunmetal non return valve 100mm dia. of approved make , tested to a pressure of 21kg/sq.cm with all fittings and accessories etc., all complete where ever required as directed by the Engineer-Incharge.

Providing and installing submersible pump with SS impeller , high tensile SS shaft , copper wound squirrel cage wet type induction motor 2880 rpm, 415 V, 50 Hz, 3phase A.C. supply , confirming to ISS: 8034-1976 , capacity 1000 litre per minute at 70-120m head along with a directly coupled submersible type squirrel cage electric induction 12.5H.P motor suitable for operation on 400V , 3phase , 50 c.p.s A.C supply , water lubricated bearings and provided with pivoted segment type thrust bearings to withstand non-vertical lead with minimum wear and tear and duly fitted with device to take up the expansion of water with heating of motor , including supply , testing and commisioning of electrical panel from the same manufacturer , complete with all accessories in all respects. The contractor to obtain approval for model and make of pumpset and suitable electrical panel has to be made. After having yield report of fully developed tube well and submite actual bore strata chart (One working and one stand by to be kept in store) Unless instructed by the Engineer-in-charge. Insulated cable and termination along with its accessories complete as required ., Supply and making straight through joint heat shrinkable type of size 4X4 sq.mm copper all complete.

Water Treatment and Pumps

Design, Supplying, installation, testing & commissioning of softerner comprising of FRP pressure vessel of suitable for working pressure of 5kg/sq.cm. The softerner should be provided with collection system base plate fitted with pp nozzels,distribution system,hydraulic injection method,ion exchange resin,regenerant NACL lined,valves piping etc.FRP regenerant tank of suitable capacity complete in all respects for complete operation and working of softner. All as per drawing and specification and as directed by the Engineer-In Charge. Softner capacity 3500 ltr per hour FRP regeneration tank of approved size with all accessories etc. complete.( Hardness upto 500 PPM). Note: The contractor shall be permitted to carryout the work based upon the approval of KPL on submission of design by the contractor.

Hydropnumatic system

Supplying , Installation and Commisioning Hydropnumatic system as per specification referred below. Product Type: VERTICAL MULTISTAGE PUMP Product Configuration Pump Classification: Hydro-Pneumatic Booster System Pump Construction: Pump With Motor Parallel Pumping System Numbers of Pump in System: 4 Pump Component Materials Version: Cast Iron & S.S AISI 304 Seal Material: Carbon/SiC/SS316/EPDM Bearing Material: Ceramic/Tungsten Carbide Rubber Parts: NBR (Nitrile) Motor Specifications Mounting: IEC Enclosure: TEFC Phase: 3 Voltage: 380-415V Efficiency Class: IE1 / EFF2 Motor Manufacturer: Lubi System Components, Accessories: Included Header Flange Rating: PN 16, Pump Controller: Single VFD with HMI & PLC, Pump Controller Rating: 5.5 HP, HPN Pressure Tank: 300 litre, Flow, rated : 100.0 l/min, Head, rated (requested) : 100.00 m, Head, rated (actual) : 100 m , 3 Working & One Stand By

Sewage Treatement Plant

Supplying, installing, testing & commissioning of 30 KLD Sewage Treatment Plant for the following duty Sewage treatment plant shall include the supply,installation, testing and commissioning of the following items: The following Civil Components will be paid in Civil Works Equalization Tank for Effluent + Eq. Tank for Sewage - 1 No Bar Screen Chamber - 1 No Oil & Grease Trap - 1 No Tube Settler - 1 No Fab Tank - 1 No Filter Feed Tank - 1 No Treated Water Tank - 1 No

Supply and fixing SS Bar screens

Supply and fixing Non clogging type submersible pumps capable of handling solids up to 25 mm having C.I. casing & CI impeller complete with all accessories, motor of required capacity, Pressure gauge on delivery line with isolation cock, level controller (with wiring) to control the level of sump automatically. Pumps shall have following duty: (grondfos / xylem ) Raw Sewage Transfer Pumps Flow rate (each) = 2500 lph Head =10-12 Mtr ,02 Nos (1W+1SB)

Supply and fixing Prefabricated MSEP MBBR & TUBE settler tank with MBBR Media & Tube Settler media with all Accessories

Air diffusion system: - Supply and fixing 2 Nos. (one working & one standby) Twin Lobe Air Blowers capable of delivering 70 m3 of free air each at 5000 MMWG driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP suitable for 415 ± 10% volts, 3 phase, 50 cycles A.hC. supply (Make Everest / Kay ), 02 Nos (1W+1SB)

Air diffusion system: - Supply and fixing Mild Steel (MS)(heavy Class) conforming to IS:1239- 1982 complete with mild steel fittings ® brand such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, including painting the pipes with desired shade of colour coding over a coat of primer (Air piping).

Air diffusion system: - Supply and fixing Non clog type air dispersion system capable of handling 3-5 cfm of air with oxygen transfer efficiency of 3-4% per/meter water depth. Air dispersion grid shall be assembled in modular form so that they can be replaced/ repaired easily from platform at the top. Air dispersion system shall be provided for sewage sump, Aerobic digester cum Thickener & Aeration Tank

Air diffusion system: - Supply and fixing Flexible pipes conforming to IS:1239- 1982 complete with fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps for submerged air piping.

Supply and fixing Centrifugal pumps having CI casing & Bronze impeller complete with all accessories, motor of required capacity, Pressure gauge on delivery line with isolation cock, level controller (with wiring) Pumps shall have following duty: (Make : Kirlokar/Leo) a) Filter Feed Pumps Flow rate (each) = 3000 lph, Head =25 -30 mtr, 02 Nos (1W+1SB)

Supplying, installing, testing and commissioning of tertiary treatment systems comprising of a MSEP pressure sand multigrade filter with Frontal Piping, Multi port Valve Battery. Filters shall be suitable for flow rate of 3000 LPH at 2.5 Kg/Sqcm working pressure Dia 600 mm, Height 1500 mm

Supplying, installing, testing and commissioning of tertiary treatment systems comprising of a MSEP Activated Carbon filter with Frontal Piping, Multi port Valve Battery. Filters shall be suitable for flow rate of 3000 LPH at 3.5 Kg/Sqcm working pressure Dia 600 mm, Height 1500 mm

Supply and fixing UPVC (heavy Class) conforming to IS:1239- 1982 complete with mild steel fittings ® brand such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, including painting the pipes with desired shade of colour coding over a coat of primer piping for complete liquid piping .

Dosing Pump Capacity Supply and fixing Capacity 0 to 6 LPH Pro aqua / e dose

FAB Media Supply and fixing PVC FAB Media

Tube Settler Media Supply and fixing PVC Tube Media Make : W2P /Equiv.

STP Control Panel Supply Installation, testing & commissioning of Electrical Panel suitable for 415 V, 3 Phase, 4 wies, 50Hz power distribution system. The panel shall be free standing flow / wall mounted, sheet metal enclosed flush front dust & venim proof with Aluminium bus bars. The painting shall be done as per relevant ISI codes as specified. Adequate size cable alley shall be provided for each cable bending & termination. (All components would be L&T/Schnieder).

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

450 mm dia. R.C.C. pipe

Providing and fixing square mouth S.W. gully trap grade "A" complete with CI grating brick manonry chamber with water tight C.I. cover with frame of 300X300 size (inside) the weight of cover not to be less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100X100 mm size P Type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making SUB HEAD : 19.0 DRAINAGE 364 Code Description Unit Rate No. channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 0.91 m deep with SFRC cover and frame (heavy duty, HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) : With Sewer bricks conforming to IS : 4885

Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying Double Flanged (screwed / welded) Centrifugally (Spun) Cast Iron, Class B (IS : 1536) : 100 mm dia C.I. Double Flanged Pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

40 mm nominal inner dia Pipes

50 mm nominal inner dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end) :

40 mm nominal bore

50 mm nominal bore

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 100 mm diameter , Class I

Description of Work / Item(s)

Amount

CIVIL WORKS

INTERNAL ELECTRIFICATION WORKS

INTERNAL PLUMBING WORKS

EXTERNAL ELECTRICAL WORKS

EXTERNAL PLUMBING WORKS

SAHUSONS INTERIORS AND BUILDERS PRIVATE LIMITED

SRICO PROJECTS PVT LTD

ABIRAMI ENGINEERING CONSTRUCTION & CO

SAHUSONS INTERIORS AND BUILDERS PRIVATE LIMITED

SRICO PROJECTS PVT LTD

ABIRAMI ENGINEERING CONSTRUCTION & CO

SAHUSONS INTERIORS AND BUILDERS PRIVATE LIMITED

Bhamys Constructions Private Limited

ABIRAMI ENGINEERING CONSTRUCTION & CO

SRICO PROJECTS PVT LTD

SAHUSONS INTERIORS AND BUILDERS PRIVATE LIMITED

ABIRAMI ENGINEERING CONSTRUCTION & CO

ABIRAMI ENGINEERING CONSTRUCTION & CO

SAHUSONS INTERIORS AND BUILDERS PRIVATE LIMITED

Bhamys Constructions Private Limited

SRICO PROJECTS PVT LTD

SAHUSONS INTERIORS AND BUILDERS PRIVATE LIMITED

ABIRAMI ENGINEERING CONSTRUCTION & CO