85957 SPL REPAIRS TO BLDG NO. PWD-09 OTM ACCN OF COMMAND HOSPITAL (SC) PUNE UNDER GE (SOUTH) PUNE

Amount

Dismantling floor, hearth or wall tiling including cement mortar rendering , bedding , and making good wall/ floor surface for laying backing coat/ PCC ,removing serviceable tiles to store and disposal of rubbish off the premises at location all as specified and directed. (Note :- The cost of making good damaged sufaces of wall/ floor and removal of material shall be deemed to be included in quoted rate and nothing extra shall be admissible on this account)

Demolition of cement Concrete( unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. (Note :- The cost of removal of demolished material shall be deemed to be included in quoted rate and nothing shall be admissible on this account)

M&L for 20 mm thick cement concrete type B-1, 1:2:4 (using 12.5 mm graded stone aggregate) as in levelling course all as specified and directed.

M&L for joint filling between two panels with mix of 85/25 bitumen and sand in 1:3 complete all as specified and directed

M & L for ISI marked 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand incl and laid over 25 mm thick crushed/ M sand bed complete all as directed.

M&L for ultracharged Vitrified ceramic tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 Sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and as directed. Note (a) 8 to 10mm thick gypsum powder slurry shall be laid over tiles to avoid scratch, damage, paint marks etc during construction work. The cost of laying gypsum powder slurry shall be deemed to be included in quoted rate and nothing extra shall be admissible on this account (b) Shade/ colour to be approved by Garrison Engineer in consultation with user.

M&L for Ultracharged Vitrified ceramic tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 Sqm as in dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick backing coat in cement mortar (1:4) on stone masonary complete all as specified and as directed. Note (a) Shade/ colour to be approved by Garrison Engineer in consultation with user.

M&L for Glazed coloured ceramic tiles 300mm x 600mm x 7 to 8 mm thick on vertical surfaces set and jointed in neat cement slurry with 3mm spacer and pointed in white or coloured epoxy grout to match laid over and including 10 mm thick backing coat in cement mortar (1:4) to maintain true plumbon stone masonary all as specified and as directed. Note (a) Shade/ colour to be approved by Garrison Engineer in consultation with user.

M&L for coloured ceramic tiles 300mm x 600mm x 7 to 8 mm thick on vertical surfaces set and jointed in neat cement slurry with 3mm spacer and pointed in white or coloured epoxy grout to match laid over and including 10 mm thick backing coat in cement mortar (1:4) to maintain true plumbon stone masonary all as specified and as directed. Note (a) Shade/ colour to be approved by Garrison Engineer in consultation with user.

M&L for tiles area exc 0.18 sqm but not exc. 0.36 sqm matt finished coloured ceramic tiles 7mm to 8 mm thick (Square or rectangular) in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile laid over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and as directed. Note (a) 8 to 10mm thick gypsum powder slurry shall be laid over tiles to avoid scratch, damage, paint marks etc during construction work. The cost of laying gypsum powder slurry shall be deemed to be included in quoted rate and nothing extra shall be admissible on this account (b) Shade/ colour to be approved by Garrison Engineer in consultation with user.

M&L for tiles area exc 0.18 sqm but not exc. 0.36 sqm satin finished coloured ceramic tiles 7mm to 8 mm thick (Square or rectangular) in dodo/skirting set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile laid over and including 10 mm thick back coating of cement mortar (1:6) complete all as specified and as directed. Note (a) Shade/ colour to be approved by Garrison Engineer in consultation with user.

M & L 300x300mm x10 to 15 mm thick heavy duty parking tiles as in floor set and jointed and pointed in coloured cement slurry match laid over 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for 20 to 25mm thick one side polished cuddapah stone slab below granite stone or as vertical support and like over & including 20 mm thick screed bed in CM 1:6 including necessary jointing and pointing and making good to disturbed surface complete all as specified and as directed.

M & L for granite (telephonic jet balck) work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Makrana white complete including screed bed or bedding layer 20 mm thick, in CM 1:6 on stone/brick masonry/ concrete surfaces all as speicified and directed.

M&L for rounding edges of stone slab one edge, such as in steps, cooking platform and other similar situation complete all as specified and directed.

M & L for cutting grooves on stone slabs such as in steps and other similar situations complete all as specified and directed.

S&F including taking down up or down steel tubing and connections 15mm dia pipes complete all as specified and as directed.

S&F including taking down up or down steel tubing and connections 20 mm dia pipes complete all as specified and as directed.

S&F including taking down up or down steel tubing and connections 25 mm dia pipes complete all as specified and as directed.

S&F in repairs Gun metal globe or gate valves of 15 mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & directed.

S&F in repairs Gun metal globe or gate valves of 20 mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & directed.

S&F in repairs Gun metal globe or gate valves of 25 mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & directed.

S&F in repair ceramic vitreous china Table Top wash Basin of Size: 550mmx400x190mm, including PVC waste pipe 32mm dia, waste coupling 32mm bore of CP incl 15mm bore CP fancy type Pillar Cock with Lift Type Operating Knob & Base Flange etc all as specified and directed.

S&F in repairs Vitreous china wash down water closet (Pedestal pattern) with P or S trap , white in colour including fixing bolts, connection to drain and to flushing pipe with low level PVC valve less symphonic action type flushing cistern of 10ltrs capacity white in colour with inlet, ball valve float and PVC flush pipe 32mm dia with white seat cover, closed pattern with flat bottom and cover and mild steel chromium plated or hinging device complete all as specified and as directed.

S&F in repair 15mm brass Bib taps with Nozzle and wall flange, fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S & F in repairs 15 mm bore pillar taps,fancy type 200 mm extension long neck body cast copper alloy with capstan heads, chromium plated , screwed down high pressure with long screwed shanks and fly nuts,complete all as specified and directed.

S&F in repairs 15mm angular stop valve/cock cast copper alloy with wall flange screwed down high pressure with cruntch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe all as specified and as directed.

All as per Ser No 27.00 above but for concealed long shank complete all as specified and directed.

S&F in repairs CP Wall mixer 3-in-1 for mixing hot & cold water screwed down for iron pipe and fixed for 15mm bore of pipe complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facing where reqd and pointing in cement mortar 1:3 to ends or edges of landings, steps , lintels etc and cutting chases for concealed water tubing,Electric line/concealed wire etc and making good, cutting n. exe 10cm girth in brick wall all as specified and as directed.

S&F in repairs for overhead Shower of 300 mm dia round shape Single flow (ABS body chrome plated with gray face plate) with Rubit cleaning system including shower arm complete all as specified and as directed.

S&F in repairs CP health faucet (ABS body) with 1 meter long flexible tube in chrome finish & Wall hook all as specified and as directed.

S&F in repairs PVC connections 15 mm size of length 600mm with PTMT nuts complete fixed to iron pipe at both end complete all as specified and as directed.

S&F in repair Stainless steel single towel rail 20 mm dia, 600 mm long (Grade 304) complete all as specified and as directed.

Supply and fixing of Toilet Paper Holder with flap stainless steel (Grade 304) complete all as specified and as directed.

S&Fof Stainless steel soap dish holder (Grade 304) fixed to plugs with CP brass screws all as specified and as directed.

S&F of Stainless steel towel Ring round (Grade 304) with round flanges complete all as specified and as directed.

S&F in repair 5 mm thick sheet glass corner shelf, 250 mm radius including CP railing and CP bracket, complete all as specified and directed

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair 125mmx125mm stainless steel chromium plated grating with removable lead fixed over floor/nahani trap with or without hole including jointing with solvent cement complete all as specified and as directed.

S&F of 20 mm ball valves, high pressure, of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe & fixed ( Minimum weight 25mm-455gms) all as specified and as directed.

M&L for broken glass coping on top of walls in CM 1:3 all as specified and as directed.

M&L for75 mm thick PCC (1:4:8) type D-2, (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed.

M&L for rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and as directed.

S&F stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.complete all as specified and directed.

M&L for framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed

S&F Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames,manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops,parts of ranges, balusters and similar articles.complete all as specified and directed.

S&F in repairs 110mm .bore-PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches/floorcomplete all as specifiedand-directed. Note :- Rate quoted shall deemed to be inclusive of necessary scaffolding / security measures as the work is to be carried out for elevated height upto 12 mtr height building.

S&F in repairs 110mm .bore-PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including taking down unservicable existing pipe complete all as specified and-directed.

S&F in repairs 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall,including taking down existing unservicable pipe complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) bends / Tee with acess door, complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) bends / Tee with acess door, complete all as specified and directed.

S & F in repairs Rotational moulded polyethylene water storage tanks of capacity 500 Litre ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position including all necesarry GI fittings including diamantling of old existing unservicable tank and depositing to MES store complete all as specified and directed.

Dismantling of single layer Mangalore pattern tiles or similar tiles in roofing etc complete all as specified and directed.

Dismantling battens for tiles shingles etc of any size including tiling fillets exc 15 cm spacing etc complete all as specified.

Dismantling of plain or corrugated steel sheeting in roof covering complete all as specified and directed.

Dismantling fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section (unframed work) complete all as specified and directed.

Dismantling timber scantling in any position (unframed wok) exc 40sqcm in section complete all as specified and directed.

M & L for 25 mm thick pre-formed filler for expansion joints complete all as specified and directed.

M&L for forming square grooves in plaster not exc 12mm deep and not exc 15mm on face complete all as specified and directed.

M&L for preparation of new steel surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and directed.

S & F roof sheeting prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick, 150GSM of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws of J hooks complete all as specified and directed.

S & F roof sheeting prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick, 150GSM of any colour having tensile strength of 550 Mpa as in roof covering / ridges, fixed with self tapping screws or J hooks complete all as specified and directed.

S & F galvalume aluminium zinc coating GI based plain steel sheet 0.63 mm thick, as in ridges, hips,valley gutter, drips and straight flashings (length and girth fixed) with grade of zinc coating 275 CGI sheet of any type complete all as specified and directed.

M&L for cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

Taking down chowkats or frames of wooden or steel not exc 1.5 sqm (without taking off shutters from frames) and making good dismantled portion with cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) complete all as specified and directed.

Taking down chowkats or frames of wooden or steel exc 1.5 sqm but not exc 4.0 Sqm (without taking off shutters from frames) and making good dismantled portion with cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) complete all as specified and directed.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm² , modules of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all asspecified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). (Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeto contractor.)

S & F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S & F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

S&F stainless steel ,100mm size of butt hinges, complete all as specified and as directed.

S&F aluminium anodised sliding door bolts 300 mm size with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 150mm size extruded aluminium alloy tower bolt fabricated type anodised complete all as specified.

Supply and fix 150mm size extruded aluminium alloy handles fabricated type anodised complete all as specified and directed.

S&F in repair Stainless Steel 304 grade Silver finish curtain rod 25 mm bore all as specified & as directed.

S &F in repairs stainless steel fancy type round shape ball bracket suitable for 25 mm bore curtain rod complete all as specified

S&F in repairs Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to steel or wooden windows / door / shutters / frames etc. complete all as specified and as directed.

M&L for Fabrication & fitting in repair of modular kitchen with cabinet/ shelves & wardrobe/ cupboard made out of 18 mm thick PVC board plain colour & laminated sheet with autoclosing hinges including providing cabinet for keeping baskets/ cutlery basket with handles/ door shutters all as specified and directed NOTE : PVC sheet fittings & fixture will be measured and paid seperately as supply only under relevant items.

Supply only 18 mm thick PVC Celuka ply of Single Side Prelam/ Rigidlam color fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Supply only 18 mm thick PVC Celuka Ply Plain White color both side fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications all as specified and directed.

Supply only 100 mm dia oval shape SS handle fancy type brass polished bright finish complete all as specified and directed.

Supply only Chrome Plated Stainless Steel 304 grade wire basket for utenisils with necessary fixing clips fixed in cupboards etc complete in all respect complete all as specified and directed.

Supply only Ball bearing runner 45 mm Telescopic (KTS - 20) full extension, load capacity 50 Kgs, complete all as specified and directed.

Supply only Auto closing hinges 35mm of 0 crank (KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters, complete all as specified and directed.

Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets (false ceiling of any thickness) complete all as specified and directed.

M & L for Providing and fixing Gypsum Board 12.5 mm thick in ceiling fixed with screw (as per manufacturers instructions) to Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including dismantling of old existing false ceiling and including two coats of oil bound distemper over primer on ceiling all as specified and directed.

M&L for PVC coloured ceiling board for ceiling , 600mm x 600mm x 5 mm thick in size, of approved brand/make, laid over and including grid work of size 600 x 600mm, made out of 0.5mm thick G.I. tee 32 x 24 mm for main, 25x24mm for cross tee and 20 x 20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle. hung from ceiling using 2 mm thick G.I. Suspension wires spaced at 1200 mm on main runners including making niches for fans/light all as specified and directed.

M & L for decorative POP cornices/moulding of pattern as per approved by Engr-in-charge of cross section area exc 13 Sqcm and not exc 25 Sqcm including two coats of oil bound distemper over primer on ceiling complete all as specified and directed.

M&L for preparation of new un decorated surfaces of ceiling incl, cornice and applying two coat of distemper oil emulsion over alkali resistant priming paint over 1 mm thk putty on ceiling complete all as specified and directed.

Supply and fixing factory made uPVC white colourCasement door with 3D hinges made of (big series) frame 67mm x 64 mm & sash 67mm x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100mm x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour Casement door with top hung ventilator with 3D and SS friction (400 x 19 x 1.9 mm) made of (big series) frame 67mm x 64 mm, sash 67mm x 110 mm & mullion 67mm x 80 mm all having wall thickness of 2.3 + 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.50 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100mm x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed. Note: (a) For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (b) Glass shall be paid separately

Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and directed. Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water, exhaust fan etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, as per approved drawing complete all as specified and directed

S & F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified and directed.

Complete removal of existing treatment and M&L for applying 3 mm thick wall care putty and applying two coats of distemper oil emulsion on walls all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M & L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified & directed.

M&L for rendering 15mm thick in cement mortar (1:6) on fair faces of brick/concrete surfaces sagol finish including taking down cement plaster all as specified and as directed.

M&L for rendering 15mm thick in cement mortar (1:6) on fair faces of brick/concrete including taking down cement plaster all as specified and as directed.

M&L for 15 mm thick rendering on fair faces of brick work, block masonry or concrete surfaces in CM 1:6 to be finished even and smooth (without using extra lime or cement) complete all as specifed and as directed.

M&L for 15 mm thick on fair faces of brick work, block masonry or concrete surfaces in CM 1:4 to be finished even and smooth (without using extra lime or cement) complete all as specifed and as directed.

M&L for prepration of newly plastered wall surface and applying two coat of oil bound distemper over 3 mm thick wall care putty complete all as specified and as directed.

M&L for prepration of newly plastered wall surface and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

M&L for removal of existing wall treatment and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

M & L for complete removal of existing treatment and applying texture paint over a coat of primer for creating the texture based effect by using required tools like brushes, sponges, spatulas and special texture rollers on wall surfaces over 2mm thick wall care putty etc complete all as specified and directed.

M&L for writing letters on PVC coloured sheet of size 450mm x 200mm x 6mm thick, Writing letters / Numerical (Building No/ name)as directed by Engineer-in-Charge and fixing to Building with screws 4No Each, Any height of Building upto 12m height, size of letter 80 x 125mm with Max of 4 letters complete all as specified and as directed.

M & L for rendering 10 mm thick in CM 1:3 on concrete surface/ Slab finished even and smooth without using extra cement with admixture of integral water proofing compound @ 3 % by weight of cement for filling depressions if any of to receive water proofing treatment complete all as specified and directed. NOTE : WPC shall be measured and paid seperatly under relavent item of schedule

Supply only integral water proofing compound complete all as specified and directed.

M&L for water proofing treatment by applying a uniform coat of primer at 0.70 kg/sqm over cement plaster,3 mm thick and weighing not less than 3.6 kg/sqm Atactic Polypropylene Polymer (APP) modified bitumen - based prefabricated five layer water proofing membrane reinforced with non woven polyester matt black finished over compatible primer at 0.40 Ltr/sqm of density at 25 degree centigrade 0.87 - 0.89 kg/litre and viscosity 70-160 cps or cold sticker and torch application of membrane with 10 cm overlap both ways after necessary preparation of surface complete as per manufacturers instructions. Apply two coats of bitumastic - aluminium paint over the membrane incl dismantling/ taking out of existing roof treatment.

S&F in repair cascade type (coloured) floor mounted water closet with low level flushing cistern single piece coloured with floor trap , PVC coloured seat cover and connecting pipe etc complete all as speicifed and directed.

S&F 12 mm thick frameless toughtened glass superior quality double door inclusive of all accessories, floor spring machine, Handle Patch fitting, frosted film etc. including dismantling of exising door of any type and size etc complete all as specified and as directed.

S&F 10 mm thick toughened polish glass confirming to IS 2553 part I and EN 12150/ 1: 2015 aqua clean with brass hard ware with crome finish with inside /Outside opening door along with all fittings and fixtures etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) 75mm thick laid in alternate bays including finishing the surfaces even and smooth using extra cement as in path , plinth protection complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as foundation filling and mass concrete complete all as specified and directed.

S&F framed work ornamental steel gate of MS Square or rectnanguler pipe, plain sheet or other sections etc. complete drilled for fixing of steel sheeting, incl MS arrows design or any other MS designed wk and necessary welding etc of grade Fe-410-W (Gde-E-250 quality B) including fittings and locking arrangements pintle hinges, stops,hand-made sliding bolts, etc complete incl dismantling structural steel incl doors or wrought iron work of any desc and any position, gates etc complete all as specified and directed.

Excavating in trenches, not exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. orfor shafts, wells, cesspits, manholes, pier holes, etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out all as specified and directed

Excavating in trenches, not exc 1.5 m deepand getting out in any type of soil all as specified and directed

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate)as foundation filling and mass concrete complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter rough finish surface of concrete complete all as specified and directed.

M&L for RCC M-25 (design Mix) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions,rough finished surface of concrete complete all as specified and directed.

M&L for RCC M-25 (design Mix) in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC M-25 (design Mix) in beam, cantilever, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.complete all as specified and directed.

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild steel bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in soil complete all as specified and as directed.

Removing the excavated materials to a distance exceeding 50mtr but not exc 250 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point all as specified and directed.

M&L for galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) all as specified and as directed.

Taking down carefully exising unserviceable aluminium point wiring (light, fan, socket or power), complete (fitting such as switches,ceiling rose, pendent, regulators etc) removing material to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately and making good disturbed surfaces of wall, floor etc. complete all as specified and as directed.

Taking down unserviceable main switch/DB, Teak wood boards etc complete all as specified and directed.

Taking down submain wiring of any size complete all as specified and directed.

M&L for point wiring in concealed with PVC insulated, unsheathed, single core multistranded copper conductor cable (FRLSH) of size 1.5 Sqmm, 1100 volts grade including 1.5 Sqmm PVC insulated, unsheathed, copper conductor cable for earth continuity wire to be drawn through in and including PVC conduit medium grade ISI marked with its acessories including necessary modular metal flush box/ pressed steel terminal boxes and modular white cover plate/ 3 mm thick ISI marked laminated sheet cover and brass screws with cup washers for fixing switches, sockets, fan regulators etc. including all necessary wall cutting chases and making good disturbed surfaces in cement mortar 1:3 for one light / CB / fan point controlled by one switch, complete all as specified and as directed.

All as per item No 136.00 above but for one 3/2 Pin 5 Amp socket out let point on the independent board complete all as specified and directed.

All as per item No 136.00 above but for one socket outlet 3/2 pin, 5 Amp, point on the same board with other switches complete all as specified and directed.

All as per item No 136.00 above but with cable 2.5 sqmm including 2.5 sqmm cable as earth wire for 15/16 amp socket point complete all as specified and directed.

S&F single pole and neutral sheet metal enclosures with a two pin and earth plug and socket complete with one double pole MCB 20 A 240 V 'C' curve complete all as specified and as directed.

S&F Modular switch 1 way 6A, 1 module complete all as specified and directed.

S&F Modular switch 1 way 16A, 1 module complete all as specified and directed.

S&F Socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F modular type fan regulator 120 Watts, 2 module, five step complete all as specified and directed.

S&F ceiling rose surface bakelite 65mmx50 mm two to three terminals complete all as specified and as directed.

S&F in replacement MCB single pole,as per specification below with connection, testing and commisionning complete all as specified and as directed. Type : Miniature Circuit Breaker (MCB) Rated Current (In) : 6A- 32A Rated Voltage (Ue) : 240V AC, 50 Hz Number of Poles : SP (Single Pole) Breaking Capacity (Icu/Ics) : 10 kA Trip Curve : C Curve Standard Compliance : IS/IEC 60898-1 / IS 8828 Mounting Type : DIN Rail (35 mm) Terminal Capacity : Up to 16–25 mm² cable (depending on rating) Protection Type : Overload & Short-Circuit Protection IP Rating : (MCB Body) IP20 (IP43 or higher if inside DB enclosure) Operating Temperature : -5°C to +55°C Mechanical Life : ≥ 10,000 operations Electrical Life : ≥ 4,000 operations Trip Free Mechanism Yes (cannot be held ON during a fault)

S & F in replacement MCB SPN as per specification below with connection, testing and commisionning complete all as specified and as directed. Specification Type : Miniature Circuit Breaker (MCB) Rated Current (In) : 40A - 63A Rated Voltage (Ue) : 240V AC, Single Phase + Neutral Frequency : 50 Hz Breaking Capacity (Icu/Ics) : 10 kA (high breaking capacity) No. of Poles : SPN (1P + N) Trip Curve : C Curve Tripping Mechanism : Thermal-Magnetic Standards : IS/IEC 60898-1 / IS 8828 Mounting Type : DIN Rail Mounting (35 mm) Enclosure Compatibility : Standard MCB Distribution Boards (DBs) Terminal Capacity : Upto 25 mm² cable (depending on model) Operating Temperature : -5°C to +55°C Protection : Overload & Short-circuit Protection IP Rating (Device) : IP20 (MCB only), higher if inside DB enclosure Mechanical Life : ≥ 10,000 operations Electrical Life : ≥ 4,000 operations

S&F in replacement MCCB as per specifications below with all accessories all as specified and directed. Specification Type: MCCB (Molded Case Circuit Breaker) Rated Current (In) : 63 Amps Rated Voltage (Ue) : 415V AC, 3-phase (or 230V AC, 1-phase) Rated Insulation Voltage (Ui) : 690V AC Frequency : 50 Hz Breaking Capacity (Icu/Ics) : 16 kA Number of Poles : 3Pole Trip Unit Type : Thermal-Magnetic (TMD) Trip Characteristics : Adjustable thermal and magnetic trip settings Mounting Type : Fixed / Plug-in / Draw-out (usually fixed) Conformity Standards : IS/IEC 60947-2 or equivalent Operating Temperature : -5°C to +55°C Mechanical Life : ≥ 10,000 operations Electrical Life : ≥ 5,000 operations Protection Class : IP20 (MCCB only), IP42-IP54 (in panel enclosure)

S & F in replacement MCB DB as per specification below with connection, testing and commisionning including taking down of existing DB of any type & size complete all as specified and as directed. Specification Type : MCB Distribution Board (SPN) Main Incomer Rating : 200 Amps Number of Ways : 12-Way SPN (i.e., 12 Single Pole outgoing + 1 Neutral Busbar) Rated Voltage (Ue) : 240V AC, 50 Hz, Single Phase Rated Insulation Voltage (Ui) : 660V AC Busbar Rating : 200A Copper Busbar (electrolytic grade, tinned) Incomer : MCB SPN 40-63 Amps Outgoing : MCBs Supported SP MCBs (6A to 32A) – C Curve typically MCB Mounting : Din Rail (standard 35 mm) Construction Type : Wall-mounted, Flush / Surface type Enclosure Material : CRCA Sheet Steel, 1.2–1.6 mm thick Finish : Powder Coated (Epoxy / RAL7035 or custom) IP Rating : IP43 (standard) Neutral & Earth Bars : Provided – tinned copper with adequate terminal capacity Cable Entry : Knockout holes – top and bottom entry Standards Compliance : IS 13032 / IS 8623 / IEC 61439 Rated Short Circuit Capacity : Upto 10 kA with MCCB / 6 kA with MCBs (depending on configuration) Accessories : Door interlock, Indicator lamps, Cable lugs, Nameplates NOTE : MCB will be measured seperatley under respective items.

S & F in replacement MCCB DB as per specification below with connection, testing and commisionning including taking down of existing DB of any type & size complete all as specified and as directed. Specification Type : MCCB Vertical Distribution Board (VTPN) Number of Ways : 4 Way (4 Outgoing MCCBs) Rated Incomer Current : 200 Amps Rated Operational Voltage (Ue) : 415V AC, 3-Phase, 50 Hz Rated Insulation Voltage (Ui) : 690V AC Incomer MCCB : 200A, 3P or 4P, 25kA/36kA/50kA (as required) Outgoing : MCB SP 6-32 Amps Busbar Rating : 200A Tinned Copper Busbar, suitable for 35–50kA short-circuit Busbar Type : Fully Shrouded, TPN (or TP) Enclosure Type : Wall-mounted, CRCA sheet steel Enclosure Thickness : 1.6 mm (minimum) Finish : Epoxy Powder Coated (RAL 7035 or equivalent) Protection Class (IP Rating) : IP43 Cable Entry : Top/Bottom Knockouts Earth & Neutral Bar : Provided – Tinned Copper Strip Mounting Arrangement : Indoor, Wall-mounted / Floor-standing (custom) Conformity Standards : IS/IEC 61439-1 & 2, IS 8623, IS 13947-2 Short Circuit Withstand : 25 kA for 1 sec or as per MCCB specs Mechanical Protection :Double Door interlock, Shrouded terminals, Padlockable door

Taking down the existing ceiling fans/exhaust fan (before carrying out ceiling repair work) and keeping them in safe custody and refixing at the same location after proper cleaning and with new 'U'clamp set with nut bolt washer, split pin and rubber bush, down rod if required and new capacitor 2.5 mfd complete including painting the fan with one coat of synthetic enamel paint white colour and connecting with PVC cable with stranded copper conductor of size 1.5 Sqmm, complete all as specified and directed. (Note: The rate quoted shall deemed to be inclusive of cost of U Clamp set,down rod, capacitor and PVC copper cable for connection.)

M&L for sub main wiring concealed type with two runs of single core, PVC insulated, unsheathed multistranded copper conductor cable of size 6 Sqmm, 1100 volts grade (FRLSH) and one run of 6 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through and including suitable size ISI marked rigid PVC conduit with all necessary accessories such as bends, tees, junction boxes, elbows complete all as specified and directed. (Note :- Two runs of 6 Sqmm cable, one run of 6 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length)

M&L for sub main wiring concealed type with two runs of single core, PVC insulated, unsheathed multistranded copper conductor cable of size 4 Sqmm, 1100 volts grade (FRLSH) and one run of 4 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through and including suitable size ISI marked rigid PVC conduit with all necessary accessories such as bends, tees, junction boxes, elbows complete all as specified and directed. (Note :- Two runs of 4 Sqmm cable, one run of 4 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length.)

M&L for sub main wiring concealed type with two runs of single core, PVC insulated, unsheathed multistranded copper conductor cable of size 2.5 Sqmm, 1100 volts grade (FRLSH) and one run of 2.5 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through and including suitable size ISI marked rigid PVC conduit with all necessary accessories such as bends, tees, junction boxes, elbows complete all as specified and directed. (Note :- Two runs of 2.5 Sqmm cable, one run of 2.5 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length.)

M& L for Earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6.3 mm thick, buried vertically in ground (Earth pit not less than 2.25 metres deep below normal ground level and top edge of the plate not less than 1.5 m below ground level), connected to and including Galvanised steel earthing wire 4mm dia by means of bolts, nuts & checknuts and washers etc; GI pipe 20 mm dia medium grade pipe for protection of G.I earth wire, both to be provided to the extent of 7.5 metres, all as shown on electrical plate No 3 of MES SSR-2009 Part-I, other end connected to electrical main switch board (inside the bldg) GI protection pipe buried in ground, laid under floors/plinths or fixed on walls or concealed in walls etc; with provision of mixture of charcoal dust & common salt packed upto minimum 150 mm all around the earth plate, including PCC 1: 3 : 6 type B-1 earth pit with RCC cover, with G.I 20 mm dia medium grade pipe and M.S funnel with wire mesh for watering arrangement, including necessary excavation and earth work in any type of strata & testing on completion including taking out old unservicable earthing complete all as specified & directed. (Note :- Cost of earth lead & protection pipe upto 7.5 m shall deemed to be incuded in quoted rate.)

S&F in replacement of LED building security light fitting 30 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, minimum efficiency of 100 lm/W, 5700 K CCT and should have supporting LM 79 & LM 80 test certificate from Govt. approved NABL accredited Lab complete all as specified and directed.

Removing the storage type electric water heater of any capacity from the existing location prior to commencement of work and keeping it in safe custody and refixing the same at the same location after completion of neceesary work in bathroom after replacing the PVC connection pipes and with new mounting toggle bolts nuts washers required etc complete all as specified and directed (Note: The rate quoted shall deemed to include the cost of toggle bolts nuts washers required however PVC connection pipes will be measured and paid separately under relevant items.)

S&F PVC metal braided connection pipes for hot water supply with brass adopters 15 mm dia and 600 mm long complete all as specified and directed.

S&F in replacement recess mounted low glare LED panellight 2'X2' size 40 watt white/warm white, minimum efficiency of 100 lm/W, 5700 K CCT and should have supporting LM 79 & LM 80 test certificate from Govt approved NABL Accredited Lab for armstrong/grid ceiling or similar ceiling mounting system complete prewired using 15 Sqmm FRLSH PVC insulated (Unsheathed) 3 core copper conductor cable 1100V grade including taking down old unservicable complete all as specified and directed. (NOTE : The quoted price shall include the cost of light & driver)

S&F in repair recess mounted circular LED down ceiling light low glare LED 20 watt white/warm white, minimum efficiency of 100 lm/W, 5700 K CCT and should have supporting LM 79 & LM 80 test certificate from Govt approved NABL Accredited Lab for armstrong/grid ceiling or similar ceiling mounting system with ceiling cut of 160 mm dia with seperate replaceable electronic driver connecting with twin core wire including cutting existing ceiling to dia required size and also matching to adjacent false ceiling services complete all as specified and directed.

S & F in reapir LED batten suitable for indoor application 20 W 4' length wall mounted, minimum efficiency of 100 lm/W, 6500 K CCT and should have supporting LM 79 & LM 80 test certificate from Govt approved NABL Accredited Lab with polycarbonate housing end cap made of ABS plastic of white colour finish and high efficiency translucence (HET) diffuser and integral electronic driver including two point surface mounting on wall/ ceiling and connecting up with twin core twisted flexible copper conductor cable of suitable size including taking down old unservicable complete all as specified and directed.

S & F LED batten suitble for indoor application 10 W 2' length wall mounted, minimum efficiency of 100 lm/W, 6500 K CCT and should have supporting LM 79 & LM 80 test certificate from Govt approved NABL Accredited Lab with polycarbonate housing end cap made of ABS plastic of white colour finish and high efficiency translucence (HET) diffuser and integral electronic driver including two point surface mounting on wall/ ceiling and connecting up with twin core twisted flexible copper conductor cable of suitable size including taking down old unservicable complete all as specified and directed.

M&L for laying XLPE underground cable 25 sqmm 4 core amoured sheathed with PVC cable stranded aluminium conductor 1100 V laid in trenches, walls/floors all as specified and directed.

Supply and laying 50 mm outer dia, double walled corrugated (DWC) HDPE duct pipe confirming to IS-16205 Pt-24 with antirodent and non flame propogating properties of approved colour complete with fittings i.e.coupler, Tee, elbow clamp for cable protection complete all as specified and directed.

M&L for cutting of existing road/ hard standing by providing suitable T&P to make suitable size trench for laying 50 mm dia pipe in road crossing etc. including the cost of making good the disturbed surface and matching with existing (Chequered tiles/Road/PCC) complete all as specified and directed.

Supply & fix GI tubing light grade 50 mm dia ISI marked with all fittings laid in trenches and fixed pole by flat iron clamps, nut, bolt, washers suitable size all as specified and directed.

Supply & fix posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

REKHA ELECTRICALS (BID ID -3456270)

M/S Sharvi Construction (BID ID -3457284)

Mourya Construction (BID ID -3456427)

S G Enterprises (BID ID -3460779)

Vijay Construction and Company (BID ID -3456357)

M/s.BAJRANG CONSTRUCTION (BID ID -3456795)

UNIQUE ENGINEERS (BID ID -3466098)