REPAIR MAINT OF HV LV ELECTRCAL SYSTEM DAY TO DAY COMPLAINTS AND IMPROVEMENT OF MES INSTALLATIONS AND CONNECTED WORKS AT SEC A DABLAN AND BARSAT UNDER GE NORTH PATIALA

Amount

Supply, fixing, including commissioning of 16M high mast 360/150--3/3 shaft in two section suitable for 47 m/sec wind speed along with head frame, luminaires carriage suitable for 6-9 luminaires in symmetrical arrangement and other accessories manufactured in factory. Supply of raising lowering system comprising double drum winch, 4mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lightning finial. (a) Supply and fix foundation bolts along with nuts, washers, anchor plate and common template. (b) Supply and fix LED type single dome aviation obstruction light. (c) Supply and fix outdoor stand mounted feeder pillar with 32A TPN MCB incomer, single dial time switch, 25A TP contactor for the automatic switching of luminaries, power tool control with 2 no 9A contactors and raise lower push button, Incoming 35 sq. mm and out going 16 & 2.5 sq. mm terminals.Complete all as specified and as directed. Make: Bajaj/Utkarsh/Jindal power corporation .

Supply, installing,commissioning and testing 100 Watt Solar AIO LED Street Light with luminair efficacy of 150 lm/W with minimum lumen output of 15000 lumens.The solar panel should be of 150W with Monocrystalline cells with 78Ah LiFePO4 battery pack. Manufacturers Logo/name must be engraved/Embossed on luminaire Housing. Manufacturer must have In-House NABL accredited laboratory with scope of testing & callibration of Electrical, Mechanical & Photometry Parameters as per IS10322:2012, IS16104, IS16106, IEC60598-1, IEC62262:2002,IEC60068-2-75, IEC60529, IES LM79, IS16102 (Part 2, Clause 8).Solar light fitting should be reliable to fit on 410 SP-31 9.00 meter long steel tubular pole complete all specified and as directed by Engineer-in-charge. The bidder should submitt below documents along with Technical bid 1) LM79 Report from NABL Accredited Lab of Light supplied. 2) Technical Data Sheet of Solar Street Light. 3) Type Test Report of Solar Street Light. 4) BIS Certificate of Battery. 5) LM80 Report of LED Chip used in fixture. 6) Data Sheet of LED Chip used in fixture.

Excavation in truches in soft/loose soil n. exc. 1.5 meter wide and n. exc. 1.5 mtr depth and getting out, including trimming the sides and forming bottom surface to required levels for fixing pole/stay assembly and laying /taking out cables complete all as specified and directed.

Material and labour for cement concrete (1:3:6) type C2 using 40mm graded stone aggregated as in foundation, filling and mass concrete including necessary form work for existing light poles damaged foundation etc complete all specified and as directed by Engineer-in-charge.

Material and labour for cement concrete (1:4:8) type D2 using 40mm graded stone aggregated as in foundation, filling and mass concrete incuding necessary form work for existing light poles damaged foundation complete all specified and as directed by Engineer-in-charge..

All as per item srl No 03 here-in-before but depth exc 1.5 Mtr and n. exc 3.00 Mtr complete all specified and as directed by Engineer-in-charge.

Material and labour for plain cement concrete type B1 ( 1:2:4) using 20 mm graded stone aggregate as cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, coping/ plinth to existing light poles damaged coping and the like including weathering , slightly rounded or chamfered angles and throating and painting the same as directed including necessary formwork complete all specified and as directed by Engineer-in-charge.

Material and labour for earthing complete with galvanised steel earth Coil of 50 mm dia have 115 turns, burried directly in to ground ( earth pit size should be 1500mm X 600mm + size of coil) not less than 1500 mm + Coil Size deep below GL with top edge of earth coil not less than 1500mm below ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 600mm all around the coil, connected to GI lead wire of 4 mm dia (1.75 m Long) by means of nuts, bolts and washers, checknuts of GI and distance of the earthing bore from the pole should be 1200mm Minimum complete all specified and as directed by Engineer-in-charge.

Supplying, transporting, erecting and fixing in repair Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws asspecified type 410 SP-31 (9.00 metres long)complete all specified and as directed by Engineer-in-charge.

Material and labour for construction of shallow foundation with concrete for the highmast considering the safe soil bearing capacity at site as 10 T/sqmtr at 2 metre depth with all materials and labour and including the erection of the high mast with the help of suitable tools and plants, wiring of luminaires with all wiring materials like PVC insulated PVC sheathed flexible cable of suitable copper conductor cores of 1.5 sq. mm, lugs, MCB and all labour and Installation of the mast feeder pillar by grouting the stand in concrete.complete all specified and as directed by Engineer-in-charge.

Supply and fixing LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lampcomplete all specified and as directed by Engineer-in-charge.

Connecting /disconnecting connection of air-conditioner in married quarters, OTM, offrs Mess from the existing over head lines complete all specified and as directed by Engineer-in-charge. Note:-Cables and materials for connection will be provided by occupant /user of the accn

Providing labour transport and T&P for locating the fault in HT/LT line in OH/UG Line/cable in by visual inspection recce of faulty area and repairs to the fault by means of replacement of Unservicible Jumpers / Fuse wires / Burnt lugs / MCCB etc. including restrain of broken/loose ACSR counductors / Earth wire. If required to make temporary connection for fault in HT/LT lines, the cable shall be given by the the AGE E/M store for temorary connection to resume the power supply urgently. Note : (i) Materials requried for fault repairs will be measured under relevant items included in BOQ. (ii) Contractor will depute the dedicated team and necessary transportation, he will completely responsible for all the safety aspects of his team. No dispute regarding safety of person would be entertain later on. If any mishappening occures during rectifaction of fault in HT/LT lines contractor will be fully liable to bear all the expenses of indls. Special Notes:- (for 66 KV Grid, Sub Stn No.3, AMN Dump Barsat and Baffle Range Dhablan) (a) Contractor will provide all set of T & P, communication device (Mobile Phone) to deployed persons, electrcian team for each sub station required for repair of HT/LT Electrical switch gear system including safety equipment such as All type of T&Ps (Bamboo ladders, screw drivers, wire/cable cutters with blades, multi meters, cutting plairs, torch lights etc) for routine maintenance and protection of the trademan incl safety equipment such as Hand gloves, Rubber boots, Sefety belt and helmets etc.

(b) On intimation of any type of repair/maintenance work of HT/LT switch gear incomer as well as out going feeder the contractor is responsible to locate the fault by the dedicated team comprising tradesman helpers required numbers as per the gravity /nature of the work involved to restore the power supply and communicate with SBA on duty and getting permit card for working on HT lines and deposit the permit card after rectification of fault, all the activities shall be carried out within reasonable time as given by the Engineer-in-Charge. (c) Contractor will provide necessary complaint slip, complaint boook & permit book, contractor will direct the instructions to indls for lodgging the complaints duly marked the location, time and date for earlier rectifications. (d) After getting the complaints, team deployed by the contractor will rectify the complaints within stipulated time i.e within 2 hours from the time of receiving of complaints. (e) Contractor should also provide a dedicated supervisor for collection of complaints from SBA, JE etc. He would be held responsible, in case complaints are not collected timely.

Supply only the HT copper fuse wire 5 Amps of capacity.

Supply only the HT copper fuse wire 10 Amps of capacity.

Supply only the HT copper fuse wire 20 Amps of capacity.

Supply only the HT copper fuse wire 32 Amps of capacity.

Supply only the HT copper fuse wire 40 Amps of capacity.

Supply only the HT copper fuse wire 60 Amps of capacity.

Supply only the HT copper fuse wire 100 Amps of capacity.

Repair/replacement of LT Jumper all as directed and specified by Engr in Charge.

Material and labour for replacement of HT Jumper complete all specified and as directed by Engineer-in-charge. Note : Materials requried for fault repairs will be measured under relevant items included in BOQ.

Supply abd fixing multi-jointed ACSR jumpers of HT over head lines with and incl XLPE/PVC insulated 11000 volts multi stranded aluminium conductor single core cable of size 120 sqmm as per colour code in sequence Red ,yellow ,blue and black for neutral incl fixing with ACSR conductors with suitable size PG (Parellel Groove) clamp complete all specified and as directed by Engineer-in-charge.Note:- Length of one jumper not exceeding more than 3.0 mtrs .

All as per item No.23.00 here-in-before but cable of size 240 Sqmm.complete all specified and as directed by Engineer-in-charge.

Material and labour for replacement of HT Loop type insulator, vitreous porcelain, white, brown or green large size, with overall dimensions 90mmx140mm, clearance of hole 25.5mm insulator complete all specified and as directed by Engineer-in-charge.

Supply and fixing pin type porcelain, vitreous, white, brown or green insulator incl one galvanised mild steel spindle, two galvanised iron washers and one galvansied iron nut, 150mm height, 150mm dia for 11000 volts grade complete all specified and as directed by Engineer-in-charge. Make:-JAYPURIA/BHEL/JAYSHREE

Supply and fixing Disc type porcelain insulator, vitreous 145mm height and 255 dia ball and socket type, white, brown and green " Two in series" assembly for tension with tension clamps for conductor, working pressure 11000 volts grade complete all as specified and directed. Make:-JAYPURIA/BHEL/JAYSHREE

Supply and fixing cable lugs aluminium any type suitable for cable up to 10 to 16 sqmm including necessary crimping with crimping tool complete all specified and as directed by Engineer-in-charge.

All as per serial item no.29.00 here-in-before but for cable of size 25 sqmm

All as per serial item no.29.00 here-in-before but for cable of size 35 sqmm

All as per serial item no.29.00 here-in-before but for cable of size 50 sqmm

All as per serial item no.29.00 here-in-before but for cable of size 70 sqmm

All as per serial item no.29.00 here-in-before but for cable of size 95 sqmm

All as per serial item no.29.00 here-in-before but for cable of size 120 sqmm

All as per serial item no.29.00 here-in-before but for cable of size 150 sqmm

All as per serial item no.29.00 here-in-before but for cable of size 185 sqmm

All as per serial item no.29.00 here-in-before but for cable of size 240 sqmm

All as per serial item no.29.00 here-in-before but for cable of size 300 sqmm

All as per serial item no.29.00 here-in-before but for cable of size 400 sqmm

Taking out wornout MCCB of any size, any make,capacity and rating complete all specified and as directed by Engineer-in-charge.

Supply and fixing MCCB with adjustable thermal and magentic setting type Release Range 63 Amps 4 Pole breaking capacity at 415 volt AC 50 Hz, 16 kA complete all specified and as directed by Engineer-in-charge.

Supply and fixing MCCB with adjustable thermal and magentic setting typeRrelease Range 100 Amps 4 Pole breaking capacity at 415 volt AC 50 Hz, 16 kA complete all specified and as directed by Engineer-in-charge..

Supply and fixing MCCB with adjustable thermal and magentic setting type Release Range 160 Amps 4 Pole breaking capacity at 415 volt AC 50 Hz 25 kA complete all specified and as directed by Engineer-in-charge.

Supply and fixing MCCB with adjustable thermal and magentic setting type Release Range 200 Amps 4 Pole breaking capacity at 415 volt AC 50 Hz 25 kA complete all specified and as directed by Engineer-in-charge..

Supply and fixing MCCB with adjustable thermal and magentic setting type Release Range 250 Amps 4 Pole breaking capacity at 415 volt AC 50 Hz 25 kA complete all specified and as directed by Engineer-in-charge..

Supply and fixing MCCB with adjustable thermal and magentic setting type Release Range 400 Amps 4 Pole breaking capacity at 415 volt AC 50 Hz 25 kA complete all as specified and directed.

Supply and fixing in replacement of LT ACB 4 Pole, 415 V, 50 KA with thermal Magnetic Release (Manual Drawout type) of capacity 630 Amps complete all specified and as directed by Engineer-in-charge.

Supply and fixing in replacement of LT ACB 4 Pole, 415 V, 50 KA with thermal Magnetic Release (Manual Drawout type) of capacity 800 Amps complete all specified and as directed by Engineer-in-charge.

Material and labour for providing necessary following stationary require to lodge the complaint, as per requirement and as per existing sample for a minimum period of 6 Months from the date of commencement of contract for 66 KV Grid, sub stn No.9 and sub stn No.3 all as directed by Engineer-in-charge:- (i) Complaint Register/books as per sample. (ii) Complaint Slip/job card as per sample. (iii) Permit book as per sample. (iii) Other materials ie glue stick,pen, pencil, carbon paper and stainless steel scale 1'.

Material and labour for Periodical cutting of trees /trimming of branches along the HT /LT overhead lines in a girth of 03 mtrs on either side of the conductors including removing the same and dumping complete all as directed by Engr-in-Charge. Note : Expenditure for necessary tool and plants required for Periodical cutting of trees / trimming of branches along the HT / LT overhead lines are deemed to be included in rate quoted by the contractor. Complete all as specified and as directed. Note:- (i) Contractor will arrange the security boards/danger boards (Man at work) at the site, so that prevent from any damaged. (ii) Contractor will liable to cutting/trimming the branches within the day after of complaint received.

Material and labour for Earthing complete with galvanized earth plate electrode 60 cm x 60cm x 6mm thick buried directly in ground to the depth of not less than 2.25 mtr below ground level with top edge of earth plate or a depth not less than 1.50 m below ground level connected to GI strip 32 x 6mm as earth lead by means of galvanized bolts, nuts check nuts and washers and necessary excavation and earth work PCC 1:2:4 type B-1 using 20mm graded brick aggregate for earth pit RCC cover , charcoal & common salt filled in alternate layers funnel with 20mm bore light grade watering pipe, 40mm dia GI pipe light grade for protection of GI strip, wire mesh and connected to earth point including testing on all as specified and shown in electric plate No 3 of SSR part I.( for Highmast) complete all specified and as directed by Engineer-in-charge.

Supply and fixing in repairs 4 core , stranded copper conductor cable 10 sqmm, PVC insulated and PVC sheathed , 1100 Volts grade for making connections to highmast light fittings complete all specified and as directed by Engineer-in-charge.

Supply and fixing single arm GRP pole of 5 mtr cyclindrical/square with bracket having high impact strength, high bending strength, non conductive, electric insulator, shock proof and non effective from chemical, salt and smog with suitable size of GI nut bolts and taper including PCC work, complete all specified and as directed by Engineer-in-charge.

Supply and fixing including commissioning and testing of 24W Solar AIO LED Street Light with luminair efficacy of 150 lm/W with minimum lumen output of 7500 lumens.The solar panel should of 36W with Monocrystalline cells with 42Ah LiFePO4 battery pack. Manufacturers Logo/name must be Engraved/Embossed on luminaire Housing. Manufacturer must have In-House NABL accredited laboratory with scope of testing & callibration of Electrical, Mechanical & Photometry Parameters as per IS10322:2012, IS16104, IS16106, IEC60598-1, IEC62262:2002, IEC60068-2-75, IEC60529, IES LM79, IS16102 (Part 2, Clause 8). complete all specified and as directed by Engineer-in-charge.The bidder should submitt below documents slong with Technical bid: 1) LM79 Report from NABL Accredited Lab of Light supplied. 2) Technical Data Sheet of Solar Street Light. 3) Type Test Report of Solar Street Light. 4) BIS Certificate of Battery. 5) LM80 Report of LED Chip used in fixture. 6) Datat Sheet of LED Chip used in fixture. 7) The bidder should subimit proof of supply of solar street light minimum quantity 500 nos. in Single Project in India.

Matrial and labour for pin point fault locating through vehicle mounted fault locating machine for the HT/LT, 11 KV/440 volts of cable sizes 25 to 400 sqmm 3/3.5/4 core complete all specified and as directed by Engineer-in-charge. Notes : (i) Contractor will liable to rectify the cables fault at urgently basis within the time of fault received for urgent location within the incl rate. (ii) Taking out HT 11 KV/LT 440 volts cable of any size and relaying of serviceable cable after rectification of fault, LT Joint and cable shall be replaced as per site requirements (excavation, earth work, sand cushioning, cable covers and joints shall be measured and paid separately).Relaying of cable for excavation upto 10 mtr has considered as a one job (iii) Contractor will be liable to rectify the cable fault at urgent basis witin the time of fault received for urgent location within the stipulated time and rate. (iv) If contractor will failed to rectiy the fault within the 24 hours from the complaint received, the penality of 200 Rs/hour will be payable.

Supply & fixing in replacement ACSR conductor of size as per site requirement to be drawn straight horizontal on over head lines on existing poles including binding with insulators. Weight of conductor shall be measured straight horizontal distance between centre of two adjacent poles and calculating weight of conductor of size and length by adding 3% extra for sag ,jointing jumpers,etc complete all specified and as directed by Engineer-in-charge.

Supply and fixing in repair outdoor type 11 KV bus bar chamber of capacity 200 Amp with on / off lever for joining 3 core HT cable with 3.15 mm thick sheet MS angle iron section 40 x 40 x6mm frame upto 60 cm, CRCA powder coated sheet metal enclosre with IP-66 protection, locking arrangement and commissioning properly complete all specified and as directed by Engineer-in-charge.

Supply and fixing in repair cable jointing kit for 11 KV (earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core x XLPE armoured aluminium conductor cable of size 50 to 95 sqmm complete all specified and as directed by Engineer-in-charge.

All as per item No.60 here-in-before but for cable size 120 to 185 Sqmm.

All as per item No.60 here-in-before but for cable size 240 to 300 Sqmm.

Supply and fxing in repair cable jointing kit for 11 KV (earthed) grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core x XLPE armoured aluminium conductor cable of size 50 to 95 sqmm complete all specified and as directed by Engineer-in-charge..

All as per Srl item No.63 here-in-before but for cable of size 120 to 185 sqmm.

All as per Srl item No.63 here-in-before but for cable of size 240 to 300 sqmm.

Supply and fixingin repair cable jointing kit for 11 KV (earthed) grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core x XLPE armoured aluminium conductor cable of size 50 to 95 sqmm complete all specified and as directed by Engineer-in-charge.

All as per Srl item No 66 here-i-before but for cable of size 120 to 185 sqmm.

All as per Srl item No 66 here-n-before but for cable size 240 to 300 sqmm.

Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armouredwith galvanised steel wire or tape and overall PVC sheathed 16 sqmm 4 core nominal cross section in service connections

Supply, installation, testing and commissioning of an outdoor, weather-proof, full-color (RGB) programmable LED SMD 1515/2020 black face (high contrast) running-letter display board of overall size 9 metres (length) × 1 metre (height) with all control equipment, power supplies, cabling and accessories including civil/structural supports ,On-site training for operation and programming with the following minimum parameters: 1.Cabinet & Construction * Die cast aluminium cabinets/galvanized steel frame, powder-coated and corrosion resistant ,Front protection: ≥5 mm anti-reflective UV-Coated polycarbonate sheet * Ingress protection: IP65 (front and rear) * Approximate depth: ≤150 mm; total weight ≈280–340 kg 2.LED Display Characteristics * Pixel pitch: P 2.5 (to be specified by bidder for ≥50 m viewing distance) * Resolution (for P2.5) minimum resolution 2480 x 400 pixel * Brightness: ≥5500 cd/m², auto/manual brightness control * Viewing angle: Horizontal ≥160°, Vertical ≥140° * Lifetime: ≥100,000 hours continuous operation 3.Electronics & Control * Asynchronous LED Nova star control system with on-board memory and scheduling * Communication: USB, LAN, Wi-Fi or 4G (bidder to specify) * Refresh rate: ≥3840 Hz * Power supply: 5 V DC regulated SMPS units, redundant design 4.Power & Environment * Max power consumption: ≤650 W/m², average ≤250 W/m² * Total typical load (9 m × 1 m): ~1.2–1.6 kW * Operating temperature: –20 °C to +60 °C; humidity 10–90 % RH non-condensing * Input supply: 230 V ±10 %, 50 Hz, single phase 5.Functional Features * Multi-language text support (Unicode – English/Hindi/Punjabi etc.) * Programmable scrolling speed, flashing, animations, and scheduled messages * Automatic brightness sensor, remote diagnostics * Mounting arrangement for wall/façade or freestanding frame with wind-load compliance as per IS 875

BANSAL ENGINEERING (BID ID -3508794)

Jawandha Enterprises (BID ID -3508866)