REPAIR/MAINT OF CHAJJA, ROOF PROJECTIONS, BALCONY ETC INCLUDING EXTERNAL PAINTING FOR BHRGAVA, DATTA, OLD AND MEW GUPTA COLONY IN DOMESTIC AREA AT AF STN UTARLAI

Amount

Supply & Erecting with MS props for temporary supports to the structural members like beams, slabs, staircase slab, chajjas etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work as per the instructions of engineer in-charge. These supports shall be provided either in the form of props or trestles fabricated using structural steel as per the requirement and as per the instruction of Engineer-In-Charge. Item rate is inclusive of the materials, all labour, supervision, tools and tackles and transportation etc., complete as per specification and as directed.(Note : The work shall be carried out upto 12.00M height and through approved company authorised applicator)

M& L for chipping of slab/columns/beams/chajjas/parapet/roof projection/balcony/staircase and removing loose mortar with chisel hammer without much impact on concrete surface, clean the surface by sand blasting the surface using river sand with minium of 6 kg pressure at the nozzle or air blow by electric pressure blower by mechanical compressor, cleaning the exposed reinforcement with wire brush & appliying rust remover in two coats over rusted reinforcement surface and providing anti corrosive coating with two component epoxt based zinc rich primer/Rust passivation Inhibitor coat at the rate of 5 sqm/Ltr with Nitozinc primer to reinforcement surface as per manufacturers instructions including all scaffolding ,machinery,tools tackels and men materials and clearing of debries complete all as specified and as directed by Engr-in-charge. (Note : The work shall be carried out upto 12.00M height and through approved company authorised applicator)

M&L for providing weld mesh size 100x100x3mm weld mesh fixing with shear connectors with 8mm dia reinforcement by drilling 75mm deep anchoring holes and filled with two component polyester resin anchoring grout (Two pack system consist of one part of resin and two part hardner) epoxy resin 200 gm per hole as per manufacturers instructions including all necessary scaffolding ,machinery,tools tackels and men materials complete all as specified and as directed by Engr-in-charge. (Note : The work shall be carried out through approved company authorised applicator and upto 12.0M height)

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm diameter including all necessary scaffolding ,machinery,tools tackels and men materials complete all as specified and as directed by Engr-in-charge.(Note : The work shall be carried out upto 12.00 M height and reinforcement bar shall also used as column/beam jacketing or other places as directed )

M&L for TMT bars 6mm to 8mm dia bar , cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm diameter including all necessary scaffolding ,machinery,tools tackels and men materials complete all as specified and as directed by Engr-in-charge. (Note : The work shall be carried out upto 12.0M height)

M&L for driiling holes with 10 mm to 20mm dia and 75 to 100mm deep as required and filling the holes after inserting of reinforcement dia 8 to 16mm for anchoring at ends/shear connector and filled the holes with two component polyester resin anchoring grout (two pack system consist of 1 part of resin and 2 hardner part) hole @ 150gm per holes with all necessary scaffolding ,machinery,tools tackels and men materials complete all as specified and as directed by Engr-in-charge. Note : 1.reinforcement shall be paid and measured separately. 2. The work shall be carried out through approved company authorised applicator & upto 12m height

M&L for providing leak proof shuttering to RCC member in any position cut to length and providing including runners supports as per manufacturers instructions and including all necessary scaffolding ,machinery,tools tackels and men materials complete all as specified and as directed by Engr-in-charge.(Note: (i) The work shall be carried out upto 12.00 M height and through approved comapny authorised applicator. (ii) The shuttering shall may also be used for column/beam jacketing work.

M&L for providing Micro concrete at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine etc all as specified and directed. Note : The work shall be carried out through approved company authorised applicator and upto 12.0M height)

M & L for Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 including dismantling old (if required) complete all as specified and directed

M & L for Cutting holes in brick walls/ stone wall upto 11cm in depth in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified

M & L for 0.50 mm thick Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet with curved at one end of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, as in sunsheds, chajjas , fixed with self tapping screws including taking down old sheets complete all as specified and directed.

M & L for 20mm to 30 mm thick cement plaster CM 1:3 with added integral waterproofing compound @ 100ml/per 50kg cement bag. Each layer thickness not exceeding 20 mm complete all as specified and directed by engr-in-charge. IWC should conforms to IS 2645-2003 and available with ISI standard Mark. (Note : The work shall be carried out through approved company authorised applicator and upto 12.0M height)

M & L for perparation the surface and applying 10 to 40 mm thick in layers , each layer n.exc 20mm thick with polymer modifed mortar (PMM) on sufcace of slab/columns/beams/chajjas/ parapet /roof projection/balcony/staircase with Renderoc chemicals including all necessary scaffolding, man and material complete all as specified and directed . Note : The work shall be carried out through approved company authorised applicator & upto 12m height

M&L for Rendering 15 mm thick on PCC block /stone masonry/concrete surfaces in CM (1:4) by mixing water proofing compound with cement as per manufacturer instruction and finish the surface even and smooth without using extra cement including taking down old plaster complete all as specified and directed. Note:- WPC will be measured & paid separately.

M&L for rendering 5mm thick on fair faces of concrete surfaces in cement mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement complete including taking down old plaster all as specified and directed.

M & L for applying bond coat on the prepared old surface of concrete/masonry to receive new polymer mortar/polymer modified martar or micro concrete with two coats of Nitobond SBR as per maufacturer specifications. Laying of reinstatement polymer mortar or micro concrete shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concrete. Item rate inclusive of all materials, labors, supervision, tools, tackles, transportation, fixing etc., complete as per specification and as directed. Note : The work shall be carried out through approved company authorised applicator and upto 12m height.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash all as specified and directed.

M&L for prepration of newly plastered external surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces in Berger/Apex in Asian /Nerolac anti fungal emulsion paint of approved brand and shade over one coat of alkali primer all as per manufacturs instructions incl necessary scaffolding incl writing letters etc complete all as specified and directed by Engr-in-charge.

Demolition of un-reinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) of any description and in any position.complete all as directed.

S&F in repairs PVC rainwater pipes 110mm single socketed in any length with rubber ring joints fixed to wall incl clamp & imbedded in PCC block complete all as specified and directed.

M & L for PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in encasing for rain water pipe and bends , apex stone complete all as specified and directed

S & F in repairs for 110 dia PVC (SWR) bends for rain water pipe complete all as specified and directed.

M & L for Providing, cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in roof kerbs or mud stops, rounded, coping or chamfered on edges etc complete all as specified and directed.

M & L for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 and including dismantling complete as specified and directed by Engineer-In-Charge

M & L for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, flat iron fillets including all necessary drilling, bolting, welding or riveting, etc, and similar work conforming to Fe-290 Gde E-165 including dismantling old complete all asspecified and directed by Engineer-In-charge.

Demolition of reinforced cement concrete in roof slab/chajjas / beams / cantilever/ balcony/ staircase etc and other suspended work of any description complete all as specifed and directed by engineer-In-Charge. (Note : The work shall be carried out upto 9.0M height)

M&L for RCC Nominal mix concretes 1:2:4 type B-1 (20mm graded stone aggregate) as in slabs supported on walls, beams and column in floor roofs landing, balconies canopies, deck slab and in shelve and the like complete all as specified and directed. (Note : The work shall be carried out upto 12.0M height)

M&L for RCC Nominal mix concretes 1:2:4 type B-1 (20mm graded stone aggregate) as in chajjas, lintel beam,lintel band etc and the like complete all as specified and directed. (Note : The work shall be carried out upto 12.0M height)

Form work for flat fair finished surfaces of concrete to soffits of suspended slabs such as roof slab beams and column in floor roofs landing, balconies canopies, deck slab and in shelve and the like n exc 200mm thick (horizontal or sloping) complete all as specified.. (Note : The work shall be carried out upto 12.0M height)

Form work for flat fair finish to chullah hoods, chajjas, troughs, lintel beam and similar items including edges complete all as specified (Note : The work shall be carried out upto 12.0M height)

M&L for providing precast cement concrete cylindrical shape balusters for railing 1:2:4 Type B-0 (12.5 mm graded aggregate), 75 mm dia thick (measured larger portion),fixed at 200 mm Centre to centre spacing including all mouldings and fixing in Cement mortar 1:2 including taking down old railing, if required complete all as specified and directed.

M&L for preparing new steel surfaces over 10 cm in width or girth of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L For complete removal of existing treatment and finishing the surface of wall including preparation of old plastered surfaces of walls and applying one coats to achieve even shade and colour of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming two coats of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces and application by hand with painting brush/roller complete all as specified and directed. Note:-The Work shall be carried out upto 03 storey building or 12m ht. through authorised applicator or agent.

Cutting down Vegetation growths like plants/trees of girth n.exc 15cm from roof tops/sides, external walls of bldgs, Chajjas, wall junctions at junctions of rain water/ CI waste water pipe junctions including removal of roots and taking out carefully possible quantity of concrete in roofs embedded in walls/slab surfaces including repairing the GI/ CI/ PVC pipe joints of that affected locations and applying TUFALO chemical (herbal rnedicine) to arrest further growth and making good the distrubed surfaces with PCC (1:2:4) type B-1 or CM 1:2 or brick work in CM 1:4 and plastering with CM 1:4 and treating tthe surfaces to match with the adjoining surfaces all as specified and directed by the . Note :- (i) The unit rate quoted shall be deemed to include the cost of scafolding/staging etc. (ii) Any CI/AC/PVC special damaged during work shall be replaced by new one to ensure leak/seapage free joint unit rate quoted shall deemed to be include cost of replacement of specials.

M & L for fixing of 300mm x 200 mm size and 20 mm thick makarana white marble tile piece machine cut bedded in 10mm thick screed bed in CM : 1:4 and cement paste on wall including polishing and grinding complete for re-writing bldg No for existing building complete all as specified and directed.

M&L for preparation of old decorated surfaces plastered or unplastered on walls including cornices pilasters by brooming down or steel wire brushing, scraping down, smoke shoot, moulds, mors and efforescent salts and treating oil and greasy spots and applying two coat of white wash on walls complete all as specified and directed.

All as per ser item No 37 above but on ceiling complete all as specified and directed.

M&L for one coat of synthetic enamel paint on old wood or wooden based surfaces of any description over 10cm width or girth including preparation surfaces complete all as specified and directed.

M&L for one coat of synthetic enamel paint on steel surfaces of any description over 10cm width or girth including preparatin of old painted steel surfaces complete all as specified and directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) n.exc 30cm high including painting of base with white and black colour up to a height of 12.0 Mtr or 03 storey bldg . complete all as specified and directed.

M&L filling surface cracks not exc 5 mm to 7 mm wide with "Dr fixit" cracks X power or equivalent polymer molified cracks filler all as per manufacturer instructions and as directed

M/s Sati Jasnath Enterprises

S.K. INFRASTRUCTURE

Devi Engineeing

M/S TANUSHREE CONSTRUCTION COMPANY

M/s Malinath Electricals

M/s B R Saran Kotda