PROVN OF STORE CEREMONIAL ITEMS

Amount

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out in hard/dense soil .

Returning ,filling in ,including spreading ,levelling,watering and well ramming in layers not exceeding 25cm in hard dense soil.

Removing surplus excavated soil to a distance exceeding 5 km but not exceeding 15 km and depositing where directed

Plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundations ,fillling and mass concrete.

M&L for RCC design mix M-25 (20mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M&L for RCC design mix M-25 (20mm graded aggregate) in Columns, pillars, piers, posts and struts

M&L for RCC design mix M-25 (20mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span

M&L for RCC design mix M-25 (20mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L for RCC design mix M-25 (20mm graded aggregate) in chajjas etc.

M&L for flat formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces of concrete.

M&L for flat formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete.

M&L for flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete.

M&L for flat formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete.

M&L for flat formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide .

M&L for flat formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete.

M&L for TMT bars 10 mm dia over cut to length,bent to shape required, including cranking ,bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia.

All as above, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

Precast cement concrete block masonry with solid blocks exc 10 cm in width in PCC 1:2:4 type B-1 and setting in cement mortar 1:4 all as specified

M & L Rendering in CM 1:3, 5mm thick on fair faces of brick work or concrete surfaces on ceiling complete all as specified.

M & L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling.surface all as specified.

M&L for Rendering with WPC in CM 1:4, 15mm thick on othe than fair faces of brick work or concrete surfaces all as specified and directed. Note : WPC shall be measured and paid separately

Supply only Intergral waterproofing compound

M&L for Rendering in CM 1:6, 10mm thick on fair faces of brick work or concrete surfaces all as specified and directed.

M & L preparation newly plastered of wall surfaces and applying two coats of acrylic smooth exterior paint of required shade (applied @ 1.67ltr/10 Sqm) over and including priming coat of exterior primer @2.20 Kg/10 Sqm) all as specified .

M & L prepation of newly plastered wall surfaces and applying two coats of distemper oil emulsion over over a coat of primer over 3mm thick wall care putty on wall all as specified and as directed .

M & L for Non-skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but exceeding 0.18 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by Engr-in-charge..

All as per item No 26 above but as in skirting/Dado

M&L for Screed bed or bedding layer of mortor 15 mm thick in CM 1:6 for laying floor finishes all as specified and directed.

M&L for Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) in sub base of floor

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces with CM 1:4 as in backing coat of skirting /dado all as specified and directed.

M&L for IInd class hard wood , Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed.

S&F 40mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and both faces are covered with decorative face veneer with lipping/frame to match

Preparation of new wood or wood based surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel with brass/bronze hinge pin.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F 200mm long Aluminium anodised, barrel tower bolts of extruded section and fixed

S & F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring

S&F 25 mm dia SS drapery rod , including brackets, decorative knobs at both ends & curtain rings 8 Nos (minimum) complete all as speccified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer- in-charge.

S&F 4mm sheet glass, ordinary quality , n exc 0.5 sqm in each glass all as specified and directed.

S&F stainless steel wire cloth 00.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless stell wire staples.

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface.

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

Supply and application of single component, seamless, spray applied, hybrid elastomeric PU based material i.e Nitoproof 725 of Fosroc chemicals (or) sikalastic 590 of Sika India Pvt Ltd (or) equivalent in any approved make as approved by GE over a coat of primer i.e Nitoproof WB primer of Fosroc chemicals (or) diluted sikalastic 590 of Sika India Pvt Ltd (or) equivalent in any approved make as approved by GE, all as recommended by manufacturer ans as specified. Note:-(i) Average minimum DFTof PU based material shall be 1mm and shall be applied by using a Graco pump. (ii) PU based material shall process the following properties solids by volume -65%, tensile strength ASTM D412-1.75Mpa, density 1.3 g/ml, elongation ASTM D-412-350%, Adhesion to substrate concrete-1.9Mpa, resistance to water-10m pressure. (iii) Rate are deemed to be include for cleaning and preparation of surface to receive PU water proofing system including filling of cracks with cementitious repair mortars i.e renderoc CS of Fosrock chemicals (or) equivalent of approved make. (iv) 10 years of guarantee shall be provided.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft loose soil.

M&L for cement concrete type D2 1:4:8 (40mm graded aggregate) in filling and mass concrete all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete

M&L for concealed Point wiring one light point controlled by one, one way switch complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed. Note : Cutting chases and making good in wall / floor will be Measured and paid seperately.

All as per item No 51 herein before but one ceiling/exhaust fan point controlled by one, one way switch.

All as per item No 51 herein before but one switch socket outlet point 5 Amps on independent board.

S&F Switch Modular 6A single pole, one way, 1 module complete all as specified and as directed.

S&F socket Modular 6/16A 2/3 pin combined 2 module complete all as specified and as directed.

S & F Moudular white cover plate with frame 3 Moudule

All as per item No. 56 above but 6 module

S & F Moudullar mettal fulush box 3 module

All as per item No. 58 above but 6 module

Supply and fixing LED lights fitting 1 x 22W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fix MCB DB, SPN, 4 ways, double door, 240 volt, Isolated neutral bar with IP54 protection, door earthing arrangement with cement spill protector, mechanical impact strength IK09 complete. Make: L&T/Legrand/ Havells

Supply and fix MCB SP 6 to 32 Amps, 240Volts, 10 KA, "B" Curve complete. Make: L&T/Legrand/ Havells

Supply and fixing SPN 32 Amp rating 240 V, 10 KA 'C' curve miniature circuit breaker (MCB) complete. Make: L&T/Legrand/ Havells

Supply and fix ceiling rose surface type bakelite 65 x 50mm with three terminals.

M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 M below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt , earth lead GI wire 4mm dia ( 8 SWG) connectd to GI earth plate elcectrode by means of bolts, nuts, check nuts, washers of galvanised iron, thimbles and other end of earth wire connected to main switch board/ feedar pillar and protected by galvanised iron pipe medium grade 15mm bore and 20mm bore medium grade GI pipe with funnel and wire mesh for watering including necessary excavation and earth works. PCC Chamber in cement concrete 1:2:4 type B-1 & RCC cover and all as shown in Electrical Plate No. 3 of SSR ( Part-I) of 2009. (i) The unit rate includes earthing wire, and protection pipe upto 7.5 metre.

M& L for making opening for fixing of Exhaust fan of size 300 mm sweep complete and making good the disturbed surface complete.

Supply and fix exhaust fan, steel bodyAC single Phase. 230V of size 300msweep with, blades, and frame andlouvers

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth

Removing excavated materials (soils) to a distance not exc 50m and depositing where directed at a level not exc. 1.5 m above the starting point

M&L for riddled earth filling in trenches above and below the cable as in cable protection. Note:- Punned thickness shall be mesured and paid.

Material and Labour in replacement for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, multi stranded, 1100 volts grade, cross-sectional area 10 Sqmm, 2 core with and including making connection by using necessary thimbles complete all as specified and directed

Supply and laid well burnt bricks sub-class 'B' designation 75 for cable protection, brick shall be laid dry flat as width of brick eqals to the length of cable and the gap between two adjacent brick shall not exceeded 10 mm, complete all as specified and as directed.

P JAYAPATHY & C0 (BID ID -3137910)

UNIQUE INDIA CONSTRUCTIONS (BID ID -3138196)

p.chinnasamy (BID ID -3129564)