SITC OF TIER III UPTIME DESIGN AND FACILITY CERTIFIED DATA CENTER

Cat (A) - Civil Works (1) Partitions

Providing and laying autoclaved aerated cement blocks masonry with 200mm thick aerocon blocks of required size made using fly ash as basic raw material, blocks conforming to IS 2185 Part 3 (1989) having density in oven dry condition 551 - 650 Kg/Cum, minimum Compressive strength 3 N/mm 2, thermal conductivity in air dry condition 0.24 W/mK, in super structure above plinth level in cement mortar 1:4 (1 cement : 4 coarse sand ) including providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work

Providing and applying plaster to wall with 18 mm thick cement plaster in two coats under layer 12mm thick cement plaster 1:5 (1 cement: 5 coarse sand) and top layer 6mm thick cement plaster 1:3 ( 1 cement : 3 coarse sand) finished rough with sponge. on external wall surfaces, including scaffolding, curing, etc. upto 10 m height from Ground level, complete all as per specifications and direction of Engineer in Charge.

Providing and fixing 50mm thick Aerocon or equivalent approved makes Cement Sandwich Panels reinforced cement bonded plain sheets on either side enclosing a light weight core composed of portland cement, binders and a mix of silicaceous and micacious material aggregate with tongue and groove arrangement. The aerated panels should have excellent acoustic properties and fire rated for two hours (3 inch thick panels) with necessary support arrangement for Closure of windows and Partition between Server Room-AandB

Providing and fixing 75mm overall thickness full height partition in straight or curved profile, with 12.5 mm thick gypsum board of approved make conforming to IS: 2095: part I. upto ceiling height consisting of G.I. frame and required board including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre.. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corner (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.

Supplying and fixing in position of 6 mm thick toughened glass partition with 3M frost film using Prefinished MDF profiled beading to be supported to the gypsum partition, etc. Complete. MDF beading finished using duco paint.

Cat (A) - Civil Works (2) Doors

Supply and Installation of Fire rated double leaf steel Door of minimum 45mm thickness of size 1500 x 2400mm of Two hours fire rating with fire rated square vision panel of size 380 mm X 380 mm. Door frame shall be double rebate profile of size 143 x 57 mm made with minimum 1.6mm thick galvanized steel sheet including SS ball bearing butt hinges, mortice sash lock, SS lever handle with internal thumb turning arrangement, heavy duty type and external key operation including heavy duty floor spring of Dorma or equivalent make etc complete

Supply and Installation of Fire rated double leaf steel Door of minimum 45mm thickness of size 1200 x 2400mm of Two hours fire rating with fire rated square vision panel of size 380 mm X 380 mm. Door frame shall be double rebate profile of size 143 x 57 mm made with minimum 1.6mm thick galvanized steel sheet including SS ball bearing butt hinges, mortice sash lock, SS lever handle with internal thumb turning arrangement, heavy duty type and external key operation including heavy duty floor spring of Dorma or equivalent make etc complete

Supply and Installation of Fire rated single leaf steel Door of minimum 45mm thickness of size 1200 x 2400mm of Two hours fire rating with fire rated square vision panel of size 380 mm X 380 mm. Door frame shall be double rebate profile of size 143 x 57 mm made with minimum 1.6mm thick galvanized steel sheet, including SS ball bearing butt hinges, mortice sash lock, SS lever handle with internal thumb turning arrangement, heavy duty type and external key operation including heavy duty floor spring of Dorma or equivalent make etc complete

Providing and Erecting in position Fully glazed double leaf door of 1500 mm (W) x 2400 mm (H) fixed glass in 12 mm thick Toughened Glass on Patch fittings of the size 3'0" X 7'0" each including top patch fitting, bottom patch fitting, patch lock, Floor Spring of reputed manufacturer and S.S handle 600mm long, 30mm dia including frosted film of llumar or approved make, shade and design on the glass. AlI damages to the floor work to be reinstated without any extra cost including the cost of other fittings and fixtures and necessary hardware, necessary holes, joints to be sealed with silicone sealant complete in all respects etc and directions of Engineer. (Door Floor Spring of Dorma BTS type, heavy duty and for single and double leaf doors and single and double actions or equivalent approved

Providing and Erecting in position Fully glazed single leaf door of 1000 mm (W) x 2100 mm (H) fixed glass in 12 mm thick Toughened Glass on Patch fittings of the size 3'0" X 7'0" each including top patch fitting, bottom patch fitting, patch lock, Floor Spring of reputed manufacturer and S.S handle 600mm long, 30mm dia including frosted film of llumar or approved make, shade and design on the glass. All damages to the floor work to be reinstated without any extra cost including the cost of other fittings and fixtures and necessary hardware, necessary holes, joints to be sealed with silicone sealant complete in all respects etc and directions of Engineer. (Door Floor Spring of Dorma BTS type, heavy duty and for single and double leaf doors and single and double actions or equivalent approved

Providing and fixing 35 mm thick ISI marked flush doors, the shutter shall be exterior grade phenol formaldehyde (PF) resin bonded, BWR grade conforming to IS : 2202 (Part I ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including lipping, cutting rebate in shutter, 4 Nos. ISI marked Stainless steel ball bearing hinges 102x76x3mm in size with S.S. screws of approved make etc. The door shall be finished with 1 mm thick decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish of approved make with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, all complete as per direction of Engineer in Charge

Cat (A) - Civil Works (3) Flooring and False Ceiling

Providing and fixing removable raised/false access flooring of approved make with possible height adjustment upto +/- 25 mm, comprising of modular load bearing floor panels supported on hot dip galvanized rectangular frameworks of 600 x 600 mm, consisting of stinger and Pedestal assembly etc. including cutting of tiles wherever required, all complete, as per the drawings, specifications, and directions of Engineer-in-charge. a) Providing pedestal assembly all steel construction hot dipped galvanized at required spacing to form modular framework. The Pedestal head assembly shall consist of a 90 x 90 x 4mm embossed head mechanically riveted to a 19mm dia rolled formed stud of suitable length and 2 check nuts for level adjustment and arresting vertical movement. The pedestal head shall have an anti-vibrational conductive cap with inbuilt isolating spacers for Panel and stringer location. The Pedestal Base assembly shall consist of 32 mm OD pipe mechanically locked on a press for perpendicularity and then welded to a base plate of 150 x 150 x 4mm thick with stiffening folds for enhanced strength and excellent grip to glue. The sub structure assembly shall be suitably anchored to the floor with suitable adhesive and fasteners of appropriate size. b) Stringers system in all steel construction hot dipped galvanized of rectangular size 20 x 32 x 1.20 mm made of min. 1.2 mm thick sheet, having holes at both ends for securing the stringers on to the pedestal head using fully threaded M-6 or higher screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum required clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. c) Providing and fixing Access Floor panel of 600 x 600 x 35mm medium grade filled Steel anti static high pressure Laminated Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern hemispherical cones and top plain sheet is fuse welded to form a panel of an overall thickness of 35mm. The top and bottom plates of Steel Gauges: top- min. 2 mm and bottom- min. 1.2 mm fused spot welded together (minimum 64 welds in each dome and 65 welds along each flange). The panel should be corrosion resistant, 40 - 60 micron epoxy coated for lifetime rust protection. Cavity formed by the top and bottom plate is filled with non combustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate upto 1.5 mm thickness but not less than 1.2 mm. The edges of the panel shall be finished in integral trim of 5mm wide PVC beading on all sides.

Providing and laying 2 mm thick antistatic PVC vinyl flooring of approved quality and colour conforming to the IS: 3462/ 1986 on the finished concrete/floor/terrazzo tiles flooring or any hard surface with necessary approved adhesive for laying antistatic PVC sheet/roll including cleaning the floor before and after laying of PVC flooring and providing thin copper strip of size about 20.00 x 0.20 mm along the periphery of room and below each joint of two sheets wherever directed with copper screws/ rivets @600 mm c/c.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts and bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with 12.5 mm thick tapered edge gypsum fire Resistant board conforming to IS: 2095-Part-I

Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of min. size 26 x 26 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, min. 4 mm GI adjustable rods with galvanized butterfly level clips of min size 85 x 30 x 0.5 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete GI Metal Ceiling Lay in perforated beveled/Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20%-22% perforation area with 1.5-1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

Cat (A) - Civil Works (4) Painting

Providing and applying of putty of average 2mm thick over plaster surface to prepare the surface even and smooth in line and level complete to the entire satisfaction of Engineer-in-charge Providing and applying of one coat of primer and two coats of fire retardant paint over the finished surface complete to the entire satisfaction of Engineer-in-charge

Cat (A) - Civil Works (5) Miscellaneous Works

Providing and fixing pictograms in 304 grade 2 mm thick brush finished Stainless steel at all levels and locations prepared using silk printing technology/ etching, filling with industrial paint in required colours and baking to the required condition at required temperature for obtaining desired shine and gloss, in required font, design, pattern and size including buffing, polishing etc. and fixing by high quality chemical tape/ adhesive of approved make on prepared surface, all complete as per architectural drawings and direction of Engineer in charge

Providing and fixing at all levels and locations, informatory/ directional/warning signages in required font, design, pattern and size made of 4 mm thick odourless Acrylic sheets of make Cast/ Acrylite/ or approved equivalent, conforming to specific gravity of 1.19, tensile strength of 69 MPA, percentage elongation of 4.2 %, modulus of elasticity 2800 MPA (ASTM –D638), refractive index of 149, (ASTM-D542) Rockwell hardness of M94 (ASTM – D785), water absorption of 0.2 % (ASTM- D570) total light transmission of 92 % (ASTM – D 1003) chemical, UV and weather resistant, having excellent insulation properties, abrasions resistant of approved color, of approved quality and make, with beveled edges having self adhesive self luminescent vinyl sheet ( film thickness >150 micron, luminescent duration 4-6 hours) of make 3M/ Avery or approved equivalent over which the signage/ letter cutout made of vinyl sheet ( film thickness > 80 micron) of make 3M/ Avery or approved equivalent is pasted in required colour, font, design, pattern, including fixing over walls/ partition/glass etc, fixing by high quality chemical tape of make 3M/ Avery or approved equivalent on prepared surface, all complete as per architectural drawings and direction of Engineer in charge.

Removing of exisitng AHU, proper closure of ducts, existing partitions, AC Ducts, removal of Tiles, Cutting and Chipping of existing floors and Disposing of debris.

Supply and fixing of Ramp using plain metal sheet, L angle and necessary supports complete as required

Supply and applying of Pest Control

Supply and construction of foundation for the Diesel Generator as per the OEM specifications with required materials and accessories complete as required

Supply and construction of 150mm height RCC platform for UPS Systems, Electrical panel, battery racks inside Electrical Room-1&2 as per the size of the equipments. The platform shall be using RCC with required finishing completed as required

Supply and construction of foundation outdoor electrical panels for a height of 600mm from the ground level. This shall required path/provision of laying of cables with required materials and accessories complete as required

Providing and fixing 18mm thick Granite of approved color and shade, gang saw cut mirror polished premoulded and prepolished machine cut for kitchen platforms of required size, approved shade, colour and texture, at all levels, laid over 20mm thick base cement mortar 1:4 (1cement : 4 coarse sand) with joints treated with white cement , mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels.

Supplying and installing overhead pantry cabinet unit of depth 450 mm and required height and length as per site and made of 18mm thick, factory laminated, BWP ply confirming to IS 710 in approved finish and shade and having all edges sealed with hot pressed PVC straight edge banding. The unit shall be hung to the wall with anchor fasteners/ clamps of approved quality and strength. The cabinet unit consists of fascia/ drop and shelves with openable shutters fitted with approved quality chrome plated metallic auto hinges, SS handles of approved design and required sizes, clamps, anchor fasteners and other required fittings and accessories all complete including necessary arrangement for strengthening of the unit for hanging (if required) with seasoned, chemically treated, painted hard wood battens/ frame standards, and direction of engineer in charge.

Providing and laying ) Flamed/ sand blasted finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the toilet all complete with 18 mm thick stone slab over 20 mm average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer in-Charge

Supply and fixing of 1200mm x 900mm Glass Magnetic Dryerase Board of approved make, made of 4mm thick glass, aluminium/ GI hanger clips, including fixing with required screws etc. all complete as per drawings, specifications and direction of Engineer in charge

Supply and fixing of Toilet cubicles made up of 12 mm thk. compact laminated HPL sheet of approved colour with door using Merino or equivalent with U and F Channels, top rail, coat hook, Privacy Thumb turn c/w Occupancy Indicator, Door Knob, Hinges with Cover, Adjustable Foot - 316 Grade, Rubber Lining for Groove, SS Screws 304 G and P.V.C Wall Plugs etc. complete. All accessories shall be SS 304 Grade as per direction of EIC

providing and fixing of Urinal Partitions with 12mm thick DuPont Corian or approved equivalent make/model. Acrylic solid surface of Shade Savannah(F) and size 910mm X 610mm fixed on to the wall with SS ‘L’ clamps of size 50mm x 4mm - 4 nos per Urinal Partition complete in all respects as per directions of engineer in charge

Providing, fixing, testing and commissioning of white coloured vitreous china wall mounting European type water closet with CP bolts, nuts, CI chair or other hanging arrangement, with concealed PVC flushing cistern, 3/6 liters flushing capacity including flush plates and internal fittings, slow falling seat cover with lid, C.P. brass hinges rubber buffers, with all accessories, including cutting and making good the wall and floors wherever required. Gap between fixtures and walls shall be filled up with approved polysulphide sealant. Hindware WC model No.20047 and cistern model No. 508179 concealo or approved equivalent

Providing, fixing, testing and commissioning of white coloured vitreous china large flat back battery based infrared sensor operated urinal basin having pre and post flushing capacity of 250 ml and 500 ml respectively, including C.I. hangers, 15mm dia inlet to built in spreaders with inbuilt waste with C.P flange, C.P Brass union and all accessories for fixing the urinal basin, cutting and making the walls and floors, wherever required. Gap between fixtures and walls shall be filled up with approved polysulphide sealant. Hindware Model No. 60013 or approved equivalent

Providing, fixing, testing and commissioning of first quality vitreous china wash basin with 32 mm dia C.P waste of standard pattern, 32mm dia C.P bottle trap, 32 mm dia C.P pipe to wall and CP wall flange, and rubber acceptors for waste connection, R.S. or C.I. painted brackets bolts, nuts, including making provision for faucets etc. cutting and making good the wall and floor, wherever required. Gap shall be filled with silicon sealant wherever required. All accessories shall be of Jaquar make or approved equivalent Hindware Model No. 10065 or approved equivalent

Providing, fixing, testing and commissioning of stainless Steel A ISI 304 (18/8) kitchen sink of approved make, single bowl of overall size 1040 mm x 510 mm bowl depth 200 mm as per I.S. 13983 with single drain board with CP cast bottle trap Jaquar Model No. ALD-769B or approved equivalent, C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required, Gaps filled with silicon sealant wherever required all complete

Supply, installation, testing and commissioning of CP Auto closing type Pillar Cock with 450 mm long SS braided flexible connection pipe complete in all respect including cutting and making good the walls wherever required.

Providing, fixing, testing and commissioning of CP two way bib cock, including all fittings and accessories, all complete

Providing and Fixing 15mm dia C.P. angle valves, as per IS: 8931 with C.P. nuts and washers, C.P. wall flange with any other items, all complete including cutting and making good the walls wherever required.

Providing, fixing, testing and commissioning of C.P. health faucet assembly including fixing of Wall hook and 1 meter long flexible tube, all complete

Providing and fixing C.P flap type toilet paper holder including cutting and making good the walls and floors wherever required

Providing and fixing Tissue/Towel Paper dispenser including screws, washers and rawl plug etc., all complete

Providing and fixing soap dish holder Including screws, washers and rawl plug etc., all complete.

Providing and fixing of plumbing works for the pantry toilets using PPR pipes for supply and PVC pipes for drain using necessary taps, valves, bends, etc. with necessarry accessories and direction of Engineer in charge

Supply and installation of MS platform outside the pantry room for material movement. The platform shall be 2000mm x 2000mm having a load bearing capacity for 1000kgs/sqm. The platform shall be using ms plate of respective thickness. The platform and structure shall be painted using rust proof paint with all required support structure and required accesories as per standards

Cat (B) - Electrical Works (1) Diesel Generator

Supply of 500kvA Diesel Generator having 280kW (at Output) Diesel Generator Set suitable for continuous rated (DG set has to deliver 280kW at the output excluding all Aux. supplies) required for its operation, complete with Diesel Engine suitable for Generator application, developing 1500RPM with directly coupled to 280kW at 0.8 Power factor, 415V, 3 Phase, neutral, 50 cycles per second, PMG/ self excited, self regulated, with brushless excitation, Alternator generally confirms to BS:5000/IS:4722. DG set shall be complete with radiator, residential type silencer, electronic governor, MS mounting frame, fuel piping from Day tank to DG sets, 24VDC Battery along with Battery charger, Battery mounting frame, oil level indicator with gauge board, and all other accessories and auxiliaries all complete as per SLD, drawings and Technical specifications. Diesel Generator set shall be mounted on cushy foot or similar type of vibration Isolators. The DG Set shall be suitable for auto-mains failure start, auto synchronization, auto load sharing and auto / manual operations. DG Set should have communication capability to integrate with BMS system via Modbus protocol with RS485 communication port so that DG set like diesel consumption, Power, current frequency, voltage and any fault alarm etc. as per the requirement of BMS system. This shall include Auto Mains Failure Panel with necessary accessories complete as required

Installation of 500kVA Diesel Generator

Supply and providing exhaust piping complete with exhaust pipe of suitable size, fibre glass insulation with aluminium cladding, pipe accessories like flanges, bends, elbows, rain protection hoods, stainless steel flexible bellow etc.. Necessary stack structural support shall be included from scope of DG exhaust pipe. All the calculation to be submitted and approval to be taken before execution. Height of exhaust pipe shall be as per pollution Board norms. The exhaust piping shall be fixed with stack supporting structure with MS angle supports, using necessary clamps, anchor bolts, vibration isolation pads, etc., the same need to be considered.

Supply, laying and testing of Power and Control cabling using 1100V grade, signal cable of 650V grade, multi core/pair, copper/ alumninum conductor, PVC insulated armour cable including its termination with double compression brass glands, lugs etc between DG set, Control panel, DG AMF and fuel starters etc. (Power/Control cable schedule shall be submitted by bidder before execution for approval)

Supply and installation of the cable trays (Ladder/ perforated) along with cable tray cover as per IS for above mentioned cables shall be supplied and installed at site as per requirement.

Supply and installation of Earthing of DG Set including supply and laying of earthing material with necessary accessories complete as required (4 Nos. Cupper & 2 Nos. G.I.)

Supply, fabrication, erection, testing and commissioning of MS HSD day tank of 990 Ltrs capacity with necessary nozzles for inlet, outlet, over flow nozzles and level indicator (HL, IL, LL) with graduation, flanged ends, etc. including Structural support. Rate shall include for giving one coat of primer and two coats of synthetic enamel paint of approved colour as per IS:2379-1963, all complete as per relevant standards and explosive norms, drawings, specifications. This shall include piping from Day tank to the DG Set with necessary accessories complete as required

Cat (B) - Electrical Works (2) Electrical Panels

Supply, installation, Testing and commissioning of compartmentalized Outdoor Type Synchronization Panel powder coated cubical panel board, free standing type, suitable for 3 phase 4 wire, 415 volts 50Hz AC supply, fabricated with CRCA sheet steel of not less than 2 mm thick, dust and vermin proof, with ventilation louvers, cable alleys, detachable gland plate, ISMC 100 channel iron base frame with following capacity, insulated aluminium bus bar, incoming and outgoing switch gears, Multifunction meters, interconnection, earthing etc., with necessary bus bar chambers, MV danger notice board, 3 phase indicating LED lamps with toggle switches and HRC control fuse, etc. This shall include the required DG controller and PLC/ microprocessor based as per single line diagram, technical specifications suitable for parallel operation of 4 Nos. of 280KW DG sets. The quoted price shall include D.G monitoring module as per specification. Any other components required for meeting the requirement for synchronization of DG sets as per DG working scheme shall be part his scope. Earthing of LV panels including supply and laying of earthing material (as applicable) i.e 50*10 sq.mm, 75*10 sq.mm, 16mm GI flexible rope, 10 mm GI flexible rope etc.for full width of board with 2 termination points, etc with necessary accessories complete as as per the specifications and Electrical SLD.

Supply, Installation, Testing and Commissioning of compartmentalized Indoor Type LT Panel, powder coated cubical panel board, free standing type, suitable for 3 phase 4 wire, 415 volts 50Hz AC supply, fabricated with CRCA sheet steel of not less than 2 mm thick, dust and vermin proof, with ventilation louvers, cable alleys, detachable gland plate, ISMC 100 channel iron base frame with following capacity, insulated aluminium bus bar, incoming and outgoing switch gears, Multifunction meters, interconnection, earthing etc., with necessary bus bar chambers, MV danger notice board, 3 phase indicating LED lamps with toggle switches and HRC control fuse, GI Earth strips of size 50mm x 6mm for full width of board with 2 termination points, etc with necessary accessories complete as per the specifications and Electrical SLD

Supply, Installation, Testing and Commissioning of compartmentalized Indoor Type HVAC Panel, powder coated cubical panel board, free standing type, suitable for 3 phase 4 wire, 415 volts 50Hz AC supply, fabricated with CRCA sheet steel of not less than 2 mm thick, dust and vermin proof, with ventilation louvers, cable alleys, detachable gland plate, ISMC 100 channel iron base frame with following capacity, insulated aluminium bus bar, incoming and outgoing switch gears, Multifunction meters, interconnection, earthing etc., with necessary bus bar chambers, MV danger notice board, 3 phase indicating LED lamps with toggle switches and HRC control fuse, GI Earth strips of size 50mm x 6mm for full width of board with 2 termination points, etc with necessary accessories complete as per the specifications and Electrical SLD

Supply, Installation, Testing and Commissioning of compartmentalized Indoor Type UPS Output Panel, powder coated cubical panel board, free standing type, suitable for 3 phase 4 wire, 415 volts 50Hz AC supply, fabricated with CRCA sheet steel of not less than 2 mm thick, dust and vermin proof, with ventilation louvers, cable alleys, detachable gland plate, ISMC 100 channel iron base frame with following capacity, insulated aluminium bus bar, incoming and outgoing switch gears, Multifunction meters, interconnection, earthing etc., with necessary bus bar chambers, MV danger notice board, 3 phase indicating LED lamps with toggle switches and HRC control fuse, GI Earth strips of size 50mm x 6mm for full width of board with 2 termination points, etc with necessary accessories complete as per the specifications and Electrical SLD

Supply, Installation, Testing and Commissioning of compartmentalized indoor Type PSB #1 and #2, powder coated cubical panel board, free standing type, suitable for 3 phase 4 wire, 415 volts 50Hz AC supply, fabricated with CRCA sheet steel of not less than 2 mm thick, dust and vermin proof, with ventilation louvers, cable alleys, detachable gland plate, ISMC 100 channel iron base frame with following capacity, insulated aluminium bus bar, incoming and outgoing switch gears, Multifunction meters, interconnection, earthing etc., with necessary bus bar chambers, MV danger notice board, 3 phase indicating LED lamps with toggle switches and HRC control fuse, GI Earth strips of size 50mm x 6mm for full width of board with 2 termination points, etc with necessary accessories complete as per the specifications and Electrical SLD

Supply, Installation, Testing and Commissioning of compartmentalized UPS PSB #3, powder coated cubical panel board, wall mount type, suitable for 3 phase 4 wire, 415 volts 50Hz AC supply, fabricated with CRCA sheet steel of not less than 2 mm thick, dust and vermin proof, with ventilation louvers, cable alleys, detachable gland plate, insulated aluminium bus bar, incoming and outgoing switch gears, Multifunction meters, interconnection, earthing etc., with necessary bus bar chambers, MV danger notice board, 3 phase indicating LED lamps with toggle switches and HRC control fuse, GI Earth strips of size 50mm x 6mm for full width of board with 2 termination points, etc with necessary accessories complete as per the specifications and Electrical SLD

Supply, Installation, Testing and Commissioning of Distribution Boards suitable for single phase made of sheet metal construction with cutouts of required size for operating the MCB/MCCB knobs in the inner cover, with powder coated metal frame and body with double door and comprising of copper bus bars, neutral and earth bar with tapped holes, Bakelite phase barriers, PVC insulator shoes for incoming wires, necessary cable adaptor boxes for incoming, required MCBs, SI Series RCCBs etc. mounted on DIN rail, Surface / flushed / Recess mounted on walls and other accessories as per the specifications and Electrical SLD

Supply, Installation, Testing and Commissioning of Distribution Boards suitable for three phase made of sheet metal construction with cutouts of required size for operating the MCB/MCCB knobs in the inner cover, with powder coated metal frame and body with double door and comprising of phase copper bus bars, neutral and earth bar with tapped holes, Bakelite phase barriers, PVC insulator shoes for incoming wires, necessary cable adaptor boxes for incoming, required MCBs, SI Series RCCBs etc. mounted on DIN rail, Surface / flushed / Recess mounted on walls and other accessories as per the specifications and Electrical SLD

Supply, Installation, Testing and Commissioning of 63A TPN Automatic Transfer switch with powder coated cubical panel board, wall mount type, suitable for 3 phase 4 wire, 415 volts 50Hz AC supply, fabricated with CRCA sheet steel of not less than 2 mm thick, dust and vermin proof, with ventilation louvers, cable alleys, detachable gland plate, insulated aluminium bus bar, interconnection, earthing etc., with necessary bus bar chambers, MV danger notice board, 3 phase indicating LED lamps with toggle switches and HRC control fuse, GI Earth strips with 2 termination points, etc with necessary accessories complete as as per the specifications and Electrical SLD

Cat (B) - Electrical Works (3) UPS Systems

Supply of 250kVA/kW (Frame Capacity) True online double conversion modular parallel Architecture UPS with 3 phase input and 3 phase output with modules for 150kVA/kW (minimum module rating from 25kVA to 50kVA). The UPS Shall have 15 minutes battery backup on full load. This shall include connecting cables, Battery rack, battery breaker and all complete necessary accessories as per drawings, technical specifications, relevant standards

Installation of 250kVA/KW UPS Systems

Cat (B) - Electrical Works (4) LT Cables

Supply and laying of 1.1kV grade, XLPE insulated, aluminium/Copper conductor, galvanized steel tape armored/unarmored power cable as per specifications. The cable shall be laid in indoor/outdoor trenches (RCC/Buried) / cable trays as required. The cable shall be clamped at regular intervals to the supports in trench or to cable trays or brick wall using clamps and fasteners as per technical specifications, relevant standards and Electrical SLD

Supply and laying of 3.5C x 400 Sq.mm Aluminium armored LSZH & FRLS Cable

Supply and laying of 3.5C x 300 Sq.mm Aluminium armored LSZH & FRLS Cable

Supply and laying of 3.5C x 240 Sq.mm Aluminium armored LSZH & FRLS Cable

Supply and laying of 4C x 240 Sq.mm unarmored Aluminium flexible LSZH & FRLS Cable

Supply and laying of 4C x 50 Sq.mm armored Aluminium LSZH & FRLS Cable

Supply and laying of 4C x 35 Sq.mm armored Aluminium LSZH & FRLS Cable

Supply and laying of 3C x 10 Sq.mm armored Aluminium LSZH & FRLS Cable

Supply and laying of 4C x 25 Sq.mm armored Aluminium LSZH & FRLS Cable

Supply and laying of 4C x 6 Sq.mm unarmored copper flexible LSZH & FRLS Cable

Supply and laying of 3C x 10 Sq.mm unarmored copper flexible LSZH & FRLS Cable

Supply and laying of 3C x 6 Sq.mm unarmored copper flexible LSZH & FRLS Cable

Supply and laying of 3C x 2.5 Sq.mm unarmored copper flexible LSZH & FRLS Cable

Supply and laying of 1C x 1.5 Sq.mm copper flexible wire

Supply and laying of 1C x 50 Sq.mm unarmored copper flexible LSZH & FRLS Cable

Supply and laying of 1C x 25 Sq.mm unarmored copper flexible LSZH & FRLS Cable

Supply and laying of 1C x 6 Sq.mm unarmored copper flexible LSZH & FRLS Cable - Green

Supply and termination of below listed PVC/XLPE cable with tinned copper lugs, nickel plated brass double compression cable glands, tapping, crimping, and all other accessories, etc. including supply of all materials all complete as per drawings, technical specifications, relevant standards

Supply and termination of 3.5C x 400 Sq.mm Aluminium armored LSZH & FRLS Cable

Supply and termination of 3.5C x 300 Sq.mm Aluminium armored LSZH & FRLS Cable

Supply and termination of 3.5C x 240 Sq.mm Aluminium armored LSZH & FRLS Cable

Supply and termination of 4C x 240 Sq.mm unarmored Aluminium flexible LSZH & FRLS Cable

Supply and termination of 4C x 50 Sq.mm armored Aluminium LSZH & FRLS Cable

Supply and termination of 4C x 35 Sq.mm armored Aluminium LSZH & FRLS Cable

Supply and termination of 3C x 10 Sq.mm armored Aluminium LSZH & FRLS Cable

Supply and termination of 4C x 25 Sq.mm armored Aluminium LSZH & FRLS Cable

Supply and termination of 4C x 6 Sq.mm unarmored copper flexible LSZH & FRLS Cable

Supply and termination of 3C x 10 Sq.mm unarmored copper flexible LSZH & FRLS Cable

Supply and termination of 3C x 6 Sq.mm unarmored copper flexible LSZH & FRLS Cable

Supply and termination of 1C x 50 Sq.mm unarmored copper flexible LSZH & FRLS Cable

Supply and termination of 1C x 25 Sq.mm unarmored copper flexible LSZH & FRLS Cable

Supply and termination of 1C x 6 Sq.mm unarmored copper flexible LSZH & FRLS Cable - Green

Cat (B) - Electrical Works (5) Cable Trays, Raceways and Conduit

Supply and Installation GI Ladder / Perforated type cable trays factory fabricated out of 14 G sheet steel, supporting angle frame at every 1.2 m or as approved, bottom angle fasteners, anchor grip bolts, synthetic enameled painting for support structure (2 coats of primer red oxide + 2 coats of synthetic enameled painting), etc. The tray shall be suspended from ceiling using anchor bolt and angle iron supports or mounted from wall. Hot Dip Galvanizing shall meet the applicable IS standard.

600 mm x 50 mm hot Dip Galvanized - GI Ladder Type

450 mm x 50 mm hot Dip Galvanized - GI Perforated

300 mm x 50 mm hot Dip Galvanized - GI Perforated

150 mm x 50 mm hot Dip Galvanized - GI Perforated

Supply and installation of fabricated 14 SWG G.I race ways / junction boxes for drawing wires for Raw power, UPS power and communication. The race ways shall be complete with base and cover, junction boxes as required, extension pieces, couplers, end plates, earthing including mechanically cutting chases in floor/ wall etc. and making the same good. The race way shall be surface / Concealed type to brick wall / flooring with necessary fixing accessories. All the raceway will have double compartments and all complete as per specifications and relevant standards

450 mm x 50 mm hot Dip Galvanized

300 mm x 50 mm hot Dip Galvanized

150 mm x 50 mm hot Dip Galvanized

Supply and laying of 2 mm thick rigid FRLS grade PVC conduit in conduit system using conduit accessories like junction boxes, collars, bends, elbows, binding wires, etc. including cutting, chasing wherever required in wall/ ceiling/ flooring and making same good all complete as per technical specifications and relevant standards,

25 mm dia conduit

32 mm dia conduit

Cat (B) - Electrical Works (6) Earthing

Supply, installation, testing and commissioning of Chemical type earthing, 3.0 Mtrs long, 80mm dia T-39 type (Chemical type) earth pipe set with back fill compound, bus for termination, SS bolts, nuts, and washers etc. including excavation, refilling and complete as required, including heavy duty cast iron cover (Medium duty) all complete as per drawings, specifications, relevant standards, and direction of Engineer in charge

Supply and running of below listed sizes of electrolytic copper / GI earth conductor tapes / wires and laid along with cable or clamped to brick wall, etc., as required. Flexible cables to be run in suitable PVC FRLS conduits. All the accessories to be consider for running the strips / Cables etc. All copper flats to be run in sleeves with accessories as required and all complete as per drawings, specifications, relevant standards, and direction of Engineer in charge

50mm x 6mm GI strip

50mm x 6mm Copper strip

Cat (B) - Electrical Works (7) Lighting

Supply, erection, testing and Commissioning of luminaries complete with fixture, lamps, ballast, driver, starter, HPF condenser, standard down rod/chain, connecting cord, PVC/GI Flexible, Poles etc, . The rate shall include all necessary fixing accessories like MS hooks, MS supports, fasteners, etc. and all complete as per drawings, specifications, relevant standards, and direction of Engineer in charge

Recessed/surface ceiling luminaire LED 36W LED, 230V, direct light emission, metal housing, powder coated white, or anodising, opal PMMA satin diffuser in synthetic material, halogen-free internal wiring, integral HF electronic control gear Protection class I, IP40 L = 595 mm, B = 595mm, H = 70mm

RECESSED ceiling downlighter for LED 15 W, 230V, direct light emission, support profile anodised, 1450 Lm, aluminium cast with rapid connection Luminance COB LED), integral HF electronic control gear Detec.

Cat (B) - Electrical Works (8) Point Wiring

Supply, installation, wiring of modular 3 Nos Single phase 6 Amps multi pin flush type Modular socket outlets controlled by individual 1 Nos.20 Amps flush type Modular SP switch in a Metal box with all complete as per technical specifications and relevant standards

Supply, installation, wiring of modular 1 Nos Single phase 6 Amps multi pin flush type Modular socket outlets controlled by individual 1 Nos.6 Amps flush type Modular SP switch in a Metal box with all complete as per technical specifications and relevant standards

Supply, installation, wiring of modular 1 Nos Single phase 6/16 Amps multi pin flush type Modular socket outlets controlled by individual 1 Nos.20 Amps flush type Modular SP switch in a Metal box with all complete as per technical specifications and relevant standards

Point wiring of lighting fixtures, using 1100 volts grade 2 Runs of 2.5 sq.mm multi strand copper conductor for main circuit and individual Light fixtures to be connected with 1.5 sqmm multi strand copper conductor, FRLS insulated wires drawn in 20/25mm dia size 2mm thick rigid FRLS PVC conduit in a concealed / open conduit system. The wiring shall be complete with all conduit and wiring accessories like deep junction boxes, collars, tees, bends, elbows, MS boxes, GI pull wires, clamps, spacers, base plate for spacers, screws, etc. The rate shall include light switch, providing mounting boxes with tapped holes for lights switches, moulded front plates with brass screws earthing of all points using 1.5 sq.mm multi strand FRLS insulated copper conductor wires., DB to switch control will be measured as circuit wiring. The switch boxes shall be flush mounted in brick wall and all complete as per drawings, specifications, relevant standards.

Two light points controlled by 6 A flush type modular switch

Three light points controlled by 6 A flush type modular switch

Four light points controlled by 6 A flush type modular switch

Supplying and fixing outdoor type 63A, 415V, TPN Industrial type socket outlet, with 4 pole and earth, metal closed plug top along with 63 A "C" curve, TPN MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Supplying and fixing indoor type 32A, 230V, DP Industrial type socket outlet, with double pole and earth, metal closed plug top along with 32A "C" curve, DP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Cat (B) - Electrical Works (9) Mobile Industrial Plug and Sockets

Supply and Installation of 32A 3 pin Mobile Industrial Plug and Socket with necessary accessories complete as required

Supply and Installation of 63A 3 pin Mobile Industrial Plug and Socket with necessary accessories complete as required

Supply and Installation of 32A 5 pin Mobile Industrial Plug and Socket with necessary accessories complete as required

Cat (B) - Electrical Works (10) Miscellaneous Works

Supply and fixing of First Aid Box

Supply and fixing of First Aid Chart

Supply and installation of exhaust fan for the Battery Rooms with a Digital Time Switch for switching on for fixed duration every day with 3 speed motor, vibration isolator ,starter,etc for fresh air. Noise level < 55 dba @ 1.0m distance. The fan shall be with casing made from mild steel duly enamel painted, adjustable pitch die cast aluminium impeller (HUB & BLADES), mounting brackets, neoprene rubber gasket to minimize vibration, inlet screen, non return damper at outlet and rated Motor with class-H insulation suitable for high temperature operation once for 250°C for 2 hours Motor with all required complete. (800CFM)

Supply of Rubber Mat of 10mm thickness of appropriate size in front and rear of all floor mount Electrical panels and Battery Racks

Preparation works for DG foundation area, trenching in power house, construction of trrench as per site condition, civil works, etc. any other works required for Data Center works

Making of Cable Trench from for Laying of cables along with 2 layers of Sand and one layer of Cuddupa Stone above the Cable. This including the excavation and Closing of trench after Cable laying. Size of the Trench: 900mm (W) x 1000mm (D)

Cat (C) - HVAC System (1) Precision Cooling System

Supply of 30kW DX based Inrow type Precision air conditioner with in-built / external automatic transfer switches, horizontal air flow pattern, can be placed in-between the racks or at the ends of rows, close to the heat source with 30kW Nominal capacity. Cold Aisle temperature should be maintained at 20+/-1 deg C, 50+/-5% RH. Unit should have DC inverter / variable speed reciprocating hermetic scroll / digital scroll / tandem compressor compatible with R410a/R407 refrigerant, crane case heater, locking disconnect switch, EC fan, Heater, Humidifier, G4 (EU4) gravimetric + Clogged Filter, 2 no rack sensor. Out door Condenser unit shall comprise of Copper coil with Aluminium fins and Axial fan with fan speed controller motor. The microprocessor control system shall have advanced diagnostic and maintenance support, enabling multiple units to communicate and work together as a team to precisely control temperature and humidity across a room. In addition, the controller network should provide a choice of Teamwork, Lead/Lag and Cascade functions.

Installation of 30kW DX based inrow type Precision air conditioner units

Supply and installation of Outdoor stands for each unit. (as per the site conditions with the rust proof material to be approved by CDAC officers and with minimum ground clearance of 5 Ft.)

Providing and fixing 18G hard drawn Copper refrigerant piping with 9 mm thick tube nitrile rubber cover including accessories bracing between indoor and outdoor air-cooled condensers of the following size with necessary supports and fittings as required - Suction Line

Providing and fixing 18G hard drawn Copper refrigerant piping with 9 mm thick tube nitrile rubber cover including accessories bracing between indoor and outdoor air-cooled condensers of the following size with necessary supports and fittings as required - Return Line

Supply and filling of R410a/407 Refrigerant Gas

Supply and laying of Interconnecting copper cabling between indoor and outdoor unit (3 Core x 2.5 Sqmm)

Supply and laying of Condensate drain piping with 32NB CPVC class pipes.

Supply and laying of Humidifier water piping with 25NB CPVC

Supply and laying of 25mm dia ball valves for Fresh water piping

Cat (C) - HVAC System (2) Cold Aisle Containment

Supply and installation of Cold Aisle Containment for the Server Room with swinging doors. The doors shall have automatic door closure, locking mechanism, etc. with necessary accessories complete as required

Double Door -1200 mm x 2100 mm

Hydro mechanical Door Closure

Passive Top Panel/600 Wide/Metal and Toughened Glass/1200

Passive Top Panel/800 Wide/Metal and Toughened Glass/1200

Vertical Panel/ Metal/600-150

Vertical Panel/ Metal/800-150

Vertical Panel/ Metal/1200-150

Cat (C) - HVAC System (3) Cooling for Other Areas

Supply, installation, testing and commissioning of Air cooled ductable ceiling mounted package unit, comprising of scroll compressors of 11.0 TR (Nominal) capacity, cooling coil, evaporator, blower and washable/cleanable filter all housed in a powder coated sheet metal cabinet of robust construction and one number Air cooled condenser unit consisting of condenser fan, copper condenser coils, including pressure testing, gas charging with R407C/ 410A refrigerant suitable for operation on 3 phase, 415 V, 50 Hz A.C supply etc. for NOC Area This shall include the following - Microprocessor controller with necessary features for power saving, precise control on Temperature, Programmable operation, fault diagnostics, Auto Restart, Anti recycle Timer and protection from single phasing, Over load and phase reversals - Initial gas charging - Outdoor Unit Stands along with complete accessories as required

Supply and installation of ducting for the 11 TR Ductable units using 24GSS sheet with required diffusers and necessary accessories complete as required for NOC Area

Supply, installation, testing and commissioning of Air cooled ductable ceiling mounted package unit, comprising of scroll compressors of 11 TR (Nominal) capacity, cooling coil, evaporator, blower and washable/cleanable filter all housed in a powder coated sheet metal cabinet of robust construction and one number Air cooled condenser unit consisting of condenser fan, copper condenser coils, including pressure testing, gas charging with R407C/ 410A refrigerant suitable for operation on 3 phase, 415 V, 50 Hz A.C supply etc. for Electrical Room This shall include the following - Microprocessor controller with necessary features for power saving, precise control on Temparature, Programmable operation, fault diagnostics, Auto Restart, Anti recycle Timer and protection from single phasing, Over load and phase reversals - Initial gas charging - Outdoor Unit Stands along with complete accessories as required

Providing and fixing 19G soft drawn Copper refrigerant piping with 9 mm thick tube nitrile rubber cover including accessories bracing between indoor and outdoor air-cooled condensers of the following size with necessary supports and fittings as required - Suction Line

Providing and fixing 19G soft drawn Copper refrigerant piping with 9 mm thick tube nitrile rubber cover including accessories bracing between indoor and outdoor air-cooled condensers of the following size with necessary supports and fittings as required - Return Line

Supply, installation, testing and commissioning of Air cooled High wall Split AC unit of 2.0 TR (Nominal) capacity with inverter technology, cooling coil, evaporator, blower and washable/cleanable filter all housed in a cabinet of robust construction and one number Air cooled condenser unit consisting of condenser fan, copper condenser coils, including pressure testing, gas charging with R407C/ 410A refrigerant suitable for operation on single/three phase, 230/415 V, 50 Hz A.C supply etc. for Battery Rooms, Central Network Room and Discussion Room This shall include the following - Microprocessor controller with necessary features for power saving, precise control on Temperature, Programmable operation, fault diagnostics, Auto Restart, Anti recycle Timer and protection from single phasing, Over load and phase reversals - Initial gas charging - Outdoor Unit Stands - 4kVA Voltage Stabilizer along with complete accessories as required

Supply, installation, testing and commissioning of Air cooled High wall Split AC unit of 1.5 TR (Nominal) capacity with inverter technology, cooling coil, evaporator, blower and washable/cleanable filter all housed in a cabinet of robust construction and one number Air cooled condenser unit consisting of condenser fan, copper condenser coils, including pressure testing, gas charging with R407C/ 410A refrigerant suitable for operation on single/three phase, 230/415 V, 50 Hz A.C supply etc. for Telco Room, Central Network Room, Network Room and Staging Room This shall include the following - Microprocessor controller with necessary features for power saving, precise control on Temperature, Programmable operation, fault diagnostics, Auto Restart, Anti recycle Timer and protection from single phasing, Over load and phase reversals - Initial gas charging - Outdoor Unit Stands - 2kVA Voltage Stabilizer along with complete accessories as required

Providing and fixing 19G soft drawn Copper refrigerant piping with 9 mm thick tube nitrile rubber cover including accessories bracing between indoor and outdoor air-cooled condensers of the following size with necessary supports and fittings as required - Suction Line

Providing and fixing 19G soft drawn Copper refrigerant piping with 9 mm thick tube nitrile rubber cover including accessories bracing between indoor and outdoor air-cooled condensers of the following size with necessary supports and fittings as required - Return Line

Supply and Installation of 25 mm CPVC pipe for Humidifier and drain piping with 6 mm thick nitrile rubber insulation including elbows, connectors, U traps, Y connections, connections and flexible tubing if any for all units to the nearest toilet /pantry drain/ or to the main shaft available as per site conditions and per directions of the Architect/Consultant/ Site engineer.

Supply and Installation of 32 mm CPVC pipe for Humidifier and drain piping with 6 mm thick nitrile rubber insulation including elbows, connectors, U traps, Y connections, connections and flexible tubing if any for all units to the nearest toilet /pantry drain/ or to the main shaft available as per site conditions and per directions of the Architect/Consultant/ Site engineer.

Supply and installation of metal structure for mounting of comfort AC outdoor units. Outdoor units shall be stacked one above the other

Supply, installation, Testing and Commissioning of Sequencer Units suitable for 2 units

Cat (D) - Safety and Security System (1) Fire Alarm System

Supply, Installation, Testing and Commissioning of Fire Alarm System comprising of Microprocessor based Addressable 2 loop Fire Alarm Control panel having a minimum of 160 detectors / devices in each detection loop with required zone, Battery charger cum battery backup for 24 Hours in Normal condition and 2 Hours in Alarm Condition complete with necessary accessories as required The panel shall be integrated with BMS, Access Control System and PA System. This includes GUI software for Fire Alarm Panel

Supply installation Testing and commissioning of Analogue Addressable Multisensor detector (Photo + Thermal) with Detector base with all mounting accessories, complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply installation Testing and commissioning of Hydrogen Sensor with all mounting accessories, complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply installation Testing and commissioning of Response Indicator with all mounting accessories, complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply, Installation, Testing and Commissioning of Addressable Dual Action Manual Pull Station (Lift and Pull) with Address Switch and all mounting accessories, complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply, Installation, Testing and Commissioning of Addressable Hooter cum Strobe with 20Hz to 20 KHz operating frequency with minimum 8 distinct sound patterns, complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply installation Testing and commissioning of Addressable Control/Relay Modules with all mounting accessories, complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply installation Testing and commissioning of Addressable Monitor Modules with all mounting accessories, complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply installation Testing and commissioning of Addressable fault Isolator Modules with all mounting accessories, complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply and fixing of Clean agent - 4 Kg hand held fire extinguisher

Supply and installation of local scar alarm with door position sensor and necessary accessories

Supply and laying of 2 twisted pair x 1.5 mm, Multistranded AT Copper, Shielded, Fire Survival, Zero Halogen Low Smoke Armoured cable, red in Colour, laid on surface with GI saddle- spacers every0.3 meters. Complete with GI Junction Box, lugs, cable compression glands, cable tags and Ferruling.

Cat (D) - Safety and Security System (2) Aspiration Based Detection System

Supply, Installation, Testing and Commissioning of Single Zone dual Pipe Laser detector Assembly (comprising of detector, filter, aspirator, and relay outputs, on-board bar graph display, auto cleaning of Laser chamber) with on board bar graph display. The panel shall have Modbus / BacNet output for High Level Interface for Soft Integration with the BMS system and FAS through relay. This shall include power supply unit and other necessary accessories complete as required

Supply, Installation, Testing and Commissioning of Sampling Pipes for Primary and Secondary Sampling, smooth Inner Bore 21mm ID and 25 mm outer dia, Plenum Rated, Sch.40, PVC Pipes with Fittings, Hi-quality Supports, accessories and Sealing compound; Red colour sampling point labels.

Supply, Installation, Testing and Commissioning of Capillary Sets complete with tube and sampling point assembly including all accessories all complete as per drawings, specifications, relevant standards, and direction of Engineer in charge.

Supply and laying of 2 twisted pair x 1.5 mm, Multistranded AT Copper, Shielded, Fire Survival, Zero Halogen Low Smoke Armoured cable, red in Colour, laid on surface with GI saddle- spacers every0.3 meters. Complete with GI Junction Box, lugs, cable compression glands, cable tags and Ferruling.

Cat (D) - Safety and Security System (3) Fire Suppression System

Supply, Installation, Testing and Commissioning of 2 - Zone NOVEC 1230 gas based Fire Suppression System with Gas Release Panel with necessary accessories complete as required

Supply and positioning of 120.0 Ltrs. Cylinder with Beta Valve and necessary accessories complete as required

Supply of NOVEC 1230 agent

Supply and installation of Beta Primary Completer Kit complete comprises of: - Solenoid With Gauge Assembly - Discharge Hose - Manual Pneumatic Actuator - Flexible interconnecting hose - Warning Sign and Name plate - Tee and Connectors - Cylinder Supervisory Switch

Supply and installation of Mid Slave Cylinder Accessories -Pressure Operated Control Head -Actuation Hose, 30" -Male Branch Tee, 5/16" Flare x 1/8"NPT -Discharge Hose, 2" x 31"

Supply and installation of End Slave Cylinder Accessories -Pressure Operated Control Head -Actuation Hose, 30" -Discharge Hose, 2" x 31" -Master Cylinder Adaptor Kit -Male Elbow, 5/16' Flare x 1/8" NPT

Supply and installation of Discharge Nozzle

Supply and installation of M.S. Seamless pipes as per ASTM A 106 Gr.B, schedule 40 with necessary fittings for entire Server Room -A and B

Supply, Installation, Testing and Commissioning of Directional Sounders with 20Hz to 20 KHz operating frequency with minimum 8 distinct sound patterns to indicate Exit doors and direct occupants for safe and fast evacuation, complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply, Installation, Testing and Commissioning of manual release switch complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply, Installation, Testing and Commissioning of abort complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply and laying of 2 twisted pair x 1.5 mm, Multistranded AT Copper, Shielded, Fire Survival, Zero Halogen Low Smoke Armoured cable, red in Colour, laid on surface with GI saddle- spacers every0.3 meters. Complete with GI Junction Box, lugs, cable compression glands, cable tags and Ferruling.

Cat (D) - Safety and Security System (4) Access Control System

Supply, Installation, Testing and Commissioning of IP Based 4 reader access controller with power supply unit, enclosure, etc. Complete with all necessary accessories as required

Supply, Installation, Testing and Commissioning of Fingerprint based Biometric cum smart card reader with mounting plates and necessary accessories complete as required

Supply, Installation, Testing and Commissioning of smart card reader with mounting plates and necessary accessories complete as required

Supply of Iclass Smart Cards

Supply, Installation, Testing and Commissioning of Emergency Break Glass Unit with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply, installation, testing and commissioning of 1200lbs Electromagnetic lock for double leaf metal doors along with magnetic contact as per the technical specification and as per requirement and complete in all respect. Potential free contact should be included in above

Supply, installation, testing and commissioning of 600lbs Electromagnetic lock for double leaf doors along with magnetic contact as per the technical specification and as per requirement and complete in all respect. Potential free contact should be included in above

Supply, installation, testing and commissioning of 1200lbs Electromagnetic lock for single leaf metal doors along with magnetic contact as per the technical specification and as per requirement and complete in all respect. Potential free contact should be included in above

Supply, installation, testing and commissioning of 600lbs Electromagnetic lock for single leaf doors along with magnetic contact as per the technical specification and as per requirement and complete in all respect. Potential free contact should be included in above

Supply and laying of 2 twisted pair x 1.5 mm, Multistranded AT Copper, Shielded, Fire Survival, Zero Halogen Low Smoke Armoured cable, black in Colour, laid on surface with GI saddle- spacers every0.3 meters. Complete with GI Junction Box, lugs, cable compression glands, cable tags and Ferruling.

Supply and laying of 4 twisted pair x 1.5 mm, Multistranded AT Copper, Shielded, Fire Survival, Zero Halogen Low Smoke Armoured cable, yellow in Colour, laid on surface with GI saddle- spacers every0.3 meters. Complete with GI Junction Box, lugs, cable compression glands, cable tags and Ferruling.

Supply and laying of 8 twisted pair x 1.5 mm, Multistranded AT Copper, Shielded, Fire Survival, Zero Halogen Low Smoke Armoured cable, blue in Colour, laid on surface with GI saddle- spacers every0.3 meters. Complete with GI Junction Box, lugs, cable compression glands, cable tags and Ferruling.

Cat (D) - Safety and Security System (5) CCTV Surveillance System

Supply installation testing and commissioning of Indoor Application IP Dome camera with 1/3" CMOS, Progressive Scan, HD1080P, 2 MP Resolution, Dual H.264 streaming or better, 25 FPS, Tamper detection, Wide dynamic Range 60 dB and Above, 3D Noise reduction, IR cut filter, Smart IR to Avoid Over exposure, Minimum Illumination:0.001 Lux, 3mm Fixed lens or better, Built-in IR illuminators effective up to 30 meters, Night Visibility for low light conditions, PoE and standard 12VDC/24VAC power input, Built-in PIR Sensor for Human Detection, Audio IN and Audio out for two way audio communication using suitable microphones and speakers, Built in Micro SD card slot for local recording, indoor surface mount enclosure, Mounted on True Ceiling / False ceiling as per site requirement (including required accessories(including required accessories like Patch Cord, IO with Back Box etc. as per schematic and specification provided.), CE / UL certified, ONVIF Compliance POC for Camera is required, if proposed camera does not pass the POC the contractor shall propose better model or different make (Complying to the specifications) at no extra cost to client.

Supply installation testing and commissioning of outdoor Application IP Bullet camera with 1/3" CMOS, Progressive Scan, HD1080P, 2 MP Resolution, Dual H.264 streaming or better, 25 FPS, Tamper detection, Wide dynamic Range 60 dB and Above, 3D Noise reduction, IR cut filter, Smart IR to Avoid Over exposure, Minimum Illumination:0.001 Lux, 3mm Fixed lens or better, Built-in IR illuminators effective up to 30 meters, Night Visibility for low light conditions, PoE and standard 12VDC/24VAC power input, Built-in PIR Sensor for Human Detection, Audio IN and Audio out for two way audio communication using suitable microphones and speakers, Built in Micro SD card slot for local recording, indoor surface mount enclosure, Mounted on True Ceiling / False ceiling as per site requirement (including required accessories(including required accessories like Patch Cord, IO with Back Box etc. as per schematic and specification provided.), CE / UL certified, ONVIF Compliance POC for Camera is required, if proposed camera does not pass the POC the contractor shall propose better model or different make (Complying to the specifications) at no extra cost to client.

Supply installation testing and commissioning of 64 channel Network Video Recorder with Digital Video Management Software for seamless integration with third party application for unlimited Management server/Recording server/Client PC for centralize monitoring, recording and video management with 64 Camera Licenses and with 5 client licenses

Supply installation testing and commissioning of storage system for 60 cameras for 30 days considering 5Mbps quality recording

Supply installation testing and commissioning of manageable access switches 24 x 10/100/1000 PoE switch with 2 x 1G combo ports and 2 x 1G SFP SR modules per switch

Supply installation testing and commissioning of 6U Wall mount rack with power manager, fans and accessories

Cat (D) - Safety and Security System (6) Rodent Repellent System

Supply, Installation, testing and commissioning of Microprocessor based Master Controller Console capable of connecting 24 Satellites per console in a single loop, and having minimum 40 characters LCD display, with on-board controls for generating frequencies from 20Khz to 60 Khz, including all accessories such as racks etc, all complete as per drawings, specifications, relevant standard

Supply, Installation, testing and commissioning of Transducer Satellite Stations with blinking LED Indication, capable of Emitting Ultrasonic sound of frequencies 20 Khz and higher with a coverage area of 500 sqft or more in all types of voids, including all accessories all complete as per drawings, specifications, relevant standards

Supply, Installation, testing and commissioning of single pair 14/40 SWG, specially coated, FRLS, sheathed Armoured cable laid on surface with GI saddle-spacers every 0.3 meters, complete with GI Junction Box, lugs, cable compression glands, cable tags, hold down clips, and ferruling, including all accessories all complete

Cat (D) - Safety and Security System (7) Water Leakage Detection System

Supply, Installation, testing and commissioning of Water leak detection panel with 4 zone detection module, sound cum strobe units, Modbus for integration with BMS and and necessary accessories complete as required

Supply and laying of Water Leak detection cable sensor of 25 Mtrs

Cat (D) - Safety and Security System (8) Building Management System

Supply, Installation, Configuring, Testing and Commissioning of BMS Server software including Access Control System Software for real-time Processing of all Data being mapped in to the system by the DDCs and Protocol Integrators. Client version BMS software for "Monitor and Control" application, complete with Advance Graphics for Real-time Graphical Depiction of the Status and Controls and also the Access / CCTV interface to Present a Powerful Single GUI for all the HVAC, Electrical, Fire, Security, for the Entire Data Center Facility. SMS and E-mail alarm notification module with unlimited user capability, SMS Paging and Email Facility for transmitting specified alarms to designated personnel. Protocol Integration Modules for High Level integration with following 3rd Party Equipments as mentioned in the data point summary. The Protocol Integrator/ Convertor shall be Capable to Integrate Open protocol systems on BACnet /Modbus/LONWORKS/M-Bus/J-Bus Protocol Made available on IP, or on serial RS 485 / 232 interface. IP based 32 Bit freely programmable Direct Digital controllers (DDCs), complete with BMS Housing Panel. The Panel shall be MS Powder Coated, IP 55 Rating for indoor. The BMS Panel shall be with proper mounting accessories for DDCs such as DIN Rails, Elemex Terminals for Cable Terminations, Dressings for internal cabling, ferruling, tagging etc. The BMS Panels shall have SMPS Power Supply to meet the power requirement of the DDCs, Instrumentation and other connected equipment. Shall be Complete with pilot relays, fuses, overload protection relays, auxiliary power output socket etc. as required to complete the installation and intended usage. One Controller with Expansion module Shall not Exceed more than 40 IOs including Spares, 4 such Controller can be kept in 1 DDC Back Box and Not more than that DDC shall be Complete with Dual Feed Power compatible Supply unit

Supply, Installation, Testing and Commissioning of Temperature and Humidity Sensor with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling.

Supply and laying of 4 twisted pair x 1.5 mm, Multistranded AT Copper, Shielded, Fire Survival, Zero Halogen Low Smoke Armoured cable, yellow in Colour, laid on surface with GI saddle- spacers every0.3 meters. Complete with GI Junction Box, lugs, cable compression glands, cable tags and Ferruling.

Supply and laying of 8 twisted pair x 1.5 mm, Multistranded AT Copper, Shielded, Fire Survival, Zero Halogen Low Smoke Armoured cable, blue in Colour, laid on surface with GI saddle- spacers every0.3 meters. Complete with GI Junction Box, lugs, cable compression glands, cable tags and Ferruling.

Cat (D) - Safety and Security System (9) Public Addressing System

Supply, Installation, Testing and commissioning of Public address/Voice Evacuation panel with sufficient number of amplifiers to operate all the speakers with at least 20% spare capacity with 8 number of zones, Microphone, Digital auto-messenger, Power supply unit, should have free contacts for zonal integration with fire alarm system, facility to trigger auto-messaging in all the zones simultaneously and manual operation of individual zone complete with MS rack.

Supply, Installation, Testing and commissioning of 6 Watt Ceiling mount public address speakers to generate 80 dB at 1 mtr.

Supply, Installation, Testing and commissioning of 6 Watt Wall mount public address speakers to generate 80 dB at 1 mtr.

Supply and laying of 2 twisted pair x 1.5 mm, Multistranded AT Copper, Shielded, Fire Survival, Zero Halogen Low Smoke Armoured cable, black in Colour, laid on surface with GI saddle- spacers every 0.3 meters. Complete with GI Junction Box, lugs, cable compression glands, cable tags and Ferruling.

Cat (E) - Passive Networking (1) Racks

Supply and installation of 42U x 600mm x 1200mm Server Racks with single leaf metal perforated front and rear doors. The rack shall have 50mm base frame, 1U, 2U, 4U blanking panels. The rack shall not have any fan modules and cutouts shall be properly closed. The rack shall have top and bottom cable entries at the rear side with cable brushes. This shall include all necessary accessories complete as required.

Supply and installation of 42U x 800mm x 1200mm Network Racks with single leaf metal perforated front and rear doors. The rack shall have 50mm base frame, 1U, 2U, 4U blanking panels. The rack shall not have any fan modules and cutouts shall be properly closed. The rack shall have top and bottom cable entries at the rear side with cable brushes. This shall include all necessary accessories complete as required.

Supply and installation of 42U x 800mm Open Network Racks with mounting kits and all necessary accessories complete as required.

Supply and fixing of Power Distribution Unit - Vertically Mounted, 32AMPs with 25 Power Outputs. (20 Power outs of IEC 320 C13 Sockets and 5 Power outs of 5/15 Amp Sockets), Electronically controlled circuits for Surge and Spike protection, LED readout for the total current being drawn from the channel, 32AMPS MCB, 5 KV AC isolated input to Ground and Output to Ground

Supply and fixing of Intelligent Power Distribution Unit with branch circuit monitoring - Vertically Mounted, 32AMPs with 25 Power Outputs. (IEC 320 C13 x 20 Nos minimum and IEC 320 C19 x 3 Nos minimum), Electronically controlled circuits for Surge and Spike protection, LED readout for the total current being drawn from the channel, 32AMPS MCB, 5 KV AC isolated input to Ground and Output to Ground

Cat (E) - Passive Networking (2) Wire Mesh cable trays

Supply and installation of 400mm x 105mm wire basket system with all required support structures and necessary accessories complete as required.

105 mm (H) x 400 mm (W) Hot dip Galvanized Cable tray

Kitasstr

CMWB-AP Drop Kit

Jointing screws for Threaded Rods

RCSN 3000mm Channel

Cat (E) - Passive Networking (3) Fiber Runner

Supply and installation of 6 x 2 Fiber Runner system with all required support structures and necessary accessories complete as required.

6-foot horizontal straight section 2 x 6

6-foot horizontal straight section snap-on cover

2x6 90º horizontal elbow

2x6 90° Horizontal Elbow Cover

2x6 Four Way Elbow

2x6 Four Way Elbow Cover

2x6 T Junction

2x6 T Junction Cover

2x6 snap-fit junction

2-Inch Express Exit low profile

2x2 flex tube attachment

New Threaded Rod Bracket Kit

Cat (E) - Passive Networking (4) OM4 Fiber Cabling

Supply and laying of 6-core MM 50/125 micron OM4 Indoor Fiber Cable, LSZH

Supply, fixing and splicing of 12F, 1U, LC MM OM4, Loaded with Pigtails, Splice tray, adapter and splice protectors

Supply, fixing and splicing of 48F, 1U, LC MM OM4, Loaded with Pigtails, Splice tray, adapter and splice protectors

Supply of LC-LC Multimode 50/125 micron OM4 Duplex Patch Cord, 2 Meter

Supply of LC-LC Multimode 50/125 micron OM4 Duplex Patch Cord, 3 Meter

Cat (E) - Passive Networking (5) Cat6A Cabling

Supply and laying of Cat 6A LSZH Cable Boxes, 305 Mtrs

Supply and termination of Cat 6A unShielded die-cast Jack without dust cover, 180° cable exit

Supply and fixing of Cat 6A, 24-port unloaded, Angled Jack Panel, SL-Series with labels and clear label covers, Height, 1U for Active

Supply of 10G, Cat 6A, LSZH, Stranded Patchcord, 2 Meter

Supply of 10G, Cat 6A, LSZH, Stranded Patchcord, 3 Meter

Cat (E) - Passive Networking (5) Cat6 Cabling

Supply and laying of Cat 6 LSZH Cable Boxes, 305 Mtrs

Supply and termination of Cat 6 UTP Jack with Strain relief and bend limiting boot

supply and fixing of Cat 6, 24-port unloaded Modular Straight Jack Panel with rear cable support bar, labels and clear label covers, Height, 1U

Supply of Cat 6, LSZH, Stranded Patchcord, 2 Meter

Supply of Cat 6, LSZH, Stranded Patchcord, 1 Meter

Supply and fixing of Quad Face Plates with back box and accessories

Supply and fixing of Dual Face Plates with back box and accessories

Cat (F) - Displays and Desktops

Supply and installation of desktop Computer with Windows 10 Operating System as per the technical specifications for BMS and Access Control

Supply and installation of Ceiling mount Interactive Digital Multimedia Projector with 3000 lumen and wireless connectivity for Meeting Room

Supply and installation of Professional grade 55” Video Wall LED Monitors arranged as 2 nos of 2x2 matrix for the NOC Room as per the technical specifications

Supply and installation of Professional grade 47” Video Wall LED Monitors for the BMS Room as per the technical specifications

Cat (G) - Uptime Certification

Travel, Lodging and Miscellaneous Expenses for Uptime Certification

Heat Load banks after commissioning of equipment's and load testing during uptime certification

Cat (I) - Buy Back Items

Buy-Back (ie minus)Cost for buy back of AHU and other materials dismantled at site

IBM India Pvt Limited