Planning, designing and development of In-Vitro Fertilization lab at KEM Hospital.

Amount

Light /Fan / Ex. fan Points

2/3 Pin Independent Plug

15 / 5 A / 6 A Combined Power Plug Socket Point with Fuse and Indicating Lamp, One 15 Amp SP Switch

5A/6A - 3/5 Pin Plug On Board

1x28W, T-5 Fixtures, comprises of M.S.Powder coated with end cap. The fixtures complete with high efficiency electronic ballast and PF= 0.98 complete with bright reflector & T-5 lamp

Ceiling fan of 1400 mm sweep with all accessories including Electronic Regulator for completing installation

fan safty wire

Fan rod

DOOR LED FIXTURES - -LED Square Recessed Downlighter?24W

Spot Light

SITC OF 14W LED STRIP LIGHT IP65 BASE WITH ALL. PROFILE AND REQUIRED ACCESORIES

IP 42 Wall/column Mounted distribution board with one Nos of DP 16/32A MCB as incomer and 8 Nos 6A/10A SP MCB as outgoing (12 way SPN DB)

IP 42 Wall/column Mounted distribution board with one Nos of 63A 4P MCB as incomer and 4 Nos 16A TP MCB as outgoing (4 way TPN DB)

Wiring for submains- casing n cap – 2 X 4 sq. mm + 1 X 4 sq. mm earth wire in 25 x 12 mm ( 3/4 in)

63 A TPN MCB

32A DP MCB

20 A Ray Roll A/c Pt

Cu armoured cables FRLS outer sheathed- 2C x 6 Sq.mm

4 c x 6 sqmm cu cable

4 c x 16 sqmm cu cable

2c x 6 sqmm cu termi

4 c x 6 sqmm cu termi

4c x 16 sqmm cu termi

600 X 600 X 3.15 mm Copper Plate, 3000mm dip with suitable size cu strip earth pit as per IS 3043

25 x 3 cu Earthing patti

10 swg cu Earthing wire

415V Main Distribution Panel 1 short circuit reating 50kA for 1 Sec. 250A

Water Heater 15 Liters

Exhaust fan of 380mm sweep

Amplifier

Microphone

6W/100V. PA Ceiling Speaker

Wiring for speakers

PVC conduit

PVC Telephone Cable -2 pair

Dome Camera

Bullet Camera

16 channel NVR

42inches LED monitor

4TB Storage (HDD)

19 inch Rack

16 CHANNEL HD Digital Video Recorder

Fire Pannel

Pannel Loop Card

Detector

Hooter

2C X 1.5 Sq. Cu Cable

2C X 1.5 Sq. Cu termination

4 X 4 Junction Box

SITC of Capacity (R-410A /R-407c or eco-friendly Refrigerant) Air Cooled type OUTDOOR UNITS of VRF system: VRF / VRV AC EQUIPMENTS 12 HP

Indoor Units :- Compact cassette type for VRF 0.8 TR Four way Cassette Type

Indoor Units :- Compact cassette type for VRF 1 TR Four way Cassette Type

Indoor Units :- Compact cassette type for VRF 1.3 TR Four way Cassette Type

Indoor Units :- Large cassette type for VRF 1.5 TR Four way Cassette Type

Indoor Units :- Large cassette type for VRF 2.8 TR Four way Cassette Type

SITC of DX double skin Air Handling Unit : 1000 - 2000 CFM Nos

SITC of Refnets as specified of pipe sizes from 1/4 " to 2" Nos

SITC of Seamless heavy gauge REFRIGERATION COPPER PIPING for VRF/ VRV system in 18 gauge, duly insulated with 13 mm/19 mm thickness. Nitrile Rubber Insulation. Refrigeration piping will have to be taken in the piping rack / Support individually connecting to Indoor units, including necessary supports, fittings, valves, Cable tray for exposed piping where ever required will be included.. The pipe sizes from 1/4 " to 1".(13 mm insulation) and 1-1/8 " to 2"(19 mm insulation) shall be used.

Providing & fixing of Drain piping as per specification.

Installation of refrigerant Y joints with insulation

MS structure for AC works Kg

Fresh air arrangements for Indoor untis

GSS Ducting:- 24 SWG Sqm

Providing thermal insulation to supply air ducting with 19mm.thickness nitrile rubber Sqm

Terminal Boxes for mounting HEPA filter in CRCA construction duly powder coated with all accessories like pressure plate, SS 304 perforated sheet, H14 Filter with 0.3 Micron down to 99.99% Efficiency, dome nut, Pressure testing nobe to accommodate ULPA filters of following sizes. Boxes should be provided with Top connection and complete with Extruded Aluminium room operated volume control dampers.:600 x 600 x 100 deep HEPAFilter - Capacity 750 Cfm.

Panel for AHUs

Electrical Power And Control Cabling.

SITC of AHU mounted Temp sensor & RH sensor

DIFFERENTIAL PRESSURE GAUGE

SITC of PVC Wall Clading 1mm

Wall Self Laveling

Top cap for wall sheet

high impact wall base

Chair rail system for wall protection and decoration

high impact Corner Guard

Demolishing brick work in lime or cement mortar including plaster, paint, etc. manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

Removing mosaic, cement marble, granites non-slippery, tandur, kotah, shahabad stone or Indian Pattern stone, glazed tiles in flooring and dado including bedding brick bat coba etc., and delivering materials in Ward Office and carting away unserviceable materials

Removing any type of flooring i.e.mosaic, cement marble, granites non-slippery, tandur, kotah, shahabad stone or Indian Pattern stone, glazed tiles in flooring including bedding brick bat coba , paver blocks of any thickness etc in open passage, footpath, or any flooring laid on ground mechanically or manually and delivering materials in Ward Office and carting away unserviceable materials.

Removing existing door or windows with frame and shutters and making good etc. to the existing surface.

4 inch siporex wall: Providing and laying autoclaved aerated (cellular) cement blocks masonry with more than 100 mm thick AAC blocks in cement mortar 1:4 (1 cement : 4 coarse sand ) including RCC stiffeners. The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work, racking of joints, scaffolding and curing,etc. completed as directed by Engineer-in-Charge.

Cement Plaster: Providing and applying 20 mm thick internal sand faced cement plaster at all heights and locations in cement mortar specified below in two coats for masonry (except stone masonry) and concrete surfaces including racking out joints, hacking of concrete surface, watering, finishing, curing, scaffolding etc complete as directed By Engineer In Charge. In cement mortar 1:3

Linten 4 inch height for wall support:Lintels, beams, plinth beams, girders, floor beam, coping.

Removing debrise till site finishing (lumsum) loading and unloading: Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all loads including all lifts involved.

SITC OF Antistatic Conductive/ Dissipative Flooring:Seamless with perfectly curved flush-covings, resistance to mechanical stresses and dynamic loads and having conductive protection characteristics, 2 mm thick, washable

Floor tiling Dado material: Providing and Fixing Vitrified Tile of size 600 x 1200 x 10mm of approved make in Dado portion

Toilet wall dado material tile: Providing and fixing 15 mm thk. Acid proof tiles approved quality, pattern and colour for dado in the areas like battary rooms etc. including preparing the surface and levelling in the desired line, backing of 20 thk. cement mortar in porportion 1:3, square cut top edge or chamfered top edge in cement mortar 1:3, cement float, machine cutting, leveling, jointing, filling the joints with acid proof epoxy mortar, finishing, curing etc complete as directed by Engineer In Charge.

Wall plaster : Providing and applying 25 mm thick (average) external sand faced cement rough cast plaster upto 10m from ground level and at all locations in cement mortar 1:4 in two coats for masonry (except stone masonry) and concrete surfaces including, providing water proofing compound to the first coat of plaster as per manufacturers specification, racking out joints, hacking of concrete surface, providing bands, drip moulds, grooves etc. finishing, curing, scaffolding etc complete as directed By Engineer In Charge.

Brick Bat coba in toilet area: Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum,thickness at khurra

Waterproofing on floor upto 3': Providing waterproofing treatment through specialized agencies as per their specifications to the flooring of water closets, bathrooms, kitchen, nahanies, washing places, sanitary blocks etc. by giving INJECTIONS with cement solution with water proofing compound into the floor slab so as to make it consistent, homogeneous and impervious against leakage, seepage etc. The sunk portion shall then be covered with brickbat waterproof coba in 1:5 c.s. of required thickness with necessary gradient for easy flow of water. Finally the floor shall be covered with joint less waterproof cement plaster in 1:3 c.s. 12 mm to 15 mm thick finished rough for receiving tiles. The average thickness of complete treatment shall not be less than 100 mm. The soil pan area will not be deducted. ( After completion of work leakage test shall be carried out after impounding the water for 7 days without any extra cost. The actual treated area will be measured and paid for).

Urinal Verticals: Providing & fixing 20mm +/- 2mm thick both side mirror polished approved colour Granite Urinal partitions of 600 mm wide & 1550 mm high with round edges moulding and fixed in C.M. 1:2and filling joints in white cement mixed with pigment to match the colour of granite including curing, cleaning etc.complete.(Basic Rate Rs 3600/sqm)

Decorative Entrance for IVF lab

Basin counter: Providing and making wash basin counter in single piece of 18 mm to 20 mm thk. telephone black granite 600mm wide, fixed over 25 to 40 mm thk black Kadappa, sandwich type construction, by making zari, in walls upto 75 mm deep & fitting the wash basin by using M.S. bracket & filling the wall surface by C.M 1:3 etc.(M.S. bracket and wash basin will be paid seperately)

SITC OF 2- Bay Scrub Sink, with Infrared Photo sensor, Digital Timer with user defined Time interval 1,3,5 and 10minutes,1 no. mixture valve and 1 nos. solenoid valves along with Manual Option Foot Operated mechanism/ Foot switch. Anti-splash metal body construction made of Stainless Steel Grade 304 polished finished. The Scrub Sink is provided with front access panel for ease of maintenance and repairs. 1 – Position size 1600 mm long

POP ceiling, wall treatment, POP groove, wall punning and Gyspsum on partiotion: Providing and fixing false ceiling with eco-friendly light weight calcium silicate tiles of Spintone/cosmos surface textured "Aerolite " make or equivalent of size 595 x 595mm having 15 mm thick densified microlook edge and 100% humidity resistence, incombustible as per BS 476 Part IV and thermal conductivity 0.043 w/m° KC and NRC 0.50 placed in true horizontal level suspended grid of size 600x600 mm made from hot dipped GI steel sections on Sillhoutte profile, rotary stitched double webbed white with 6mm reveal profile (white/black), where in main T runner of size 24 mm x 38mm and 0.33 mm thick @ 1200mm center to center and cross T of size 24mm X 28 mm and 0.33 mm thick, 1200 mm long spaced between main tee at 600 mm centre to centre and secondary cross T of Size 24mm X 28 mm x 0.33 thick of length 600 mm to be inter locked at middle of the first cross T in each panel to form grids of 600 mm x 600 mm and resting on periphery wall profile wall section 24 mm x 24mm x 0.40 thickness and laying false ceiling for services like diffusers grills including cutting, making opening for light fitting, fixtures, smoke detectors etc. wherever required, main tee runner to be suspended form ceiling using G.I. soffit cleats of size 25 x 35 x 1.6 mm of required length fixed to the ceiling with12.5mm dia and 50 mm long dash fastener, 4 mm dia G.l adjustable rods with good quality G.I level adjustment clips of 85 X 30 X 0.8mm spaced at 1200 mm center to center along main tee all complete at all heights as per specifications, drawings and as per direction of Engineer - in - Charge.

Providing and applying Plaster of Paris punning to walls, beams, ceilings, columns in perfect line and level over the base of single coat cement plaster including roughening of existing surface making 6 mm groove at skirting and door, window jamb, sill, lintel, etc. complete. The rate is exclusive of base coat cement plaster.

Includes lamination, P.U. coating and Duco paint, Silver leafing, wallpaper and any artist design, other wall covering material etc.: Melamine polish by applying 2 coats of Asian Paints Woodtech sealer or equivalent, 1 coat of Asian Paints Woodtech exterior wood stain or equivalent of shade directed by Architect, followed by 2 coats of Asian Paints Woodtech Gold melamyne clear matt finish or equivalent, complete to the old or new wood including preparing surface by scraping, sandpapering and wipe cleaning after every coat, using spray machine for all the coats, adding thinner to every coat, scaffolding if required, etc.

Providing and fixing wall paper / Graphic for highlighting the walls with proper adhesive in line level for reception, conference & Auditorium rooms and wherever required as per the drawings. Basic rate of Wall paper is Rs..100/- per Sft. Make - D'decor / Nilaya By Asian Paints or equivalent

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 20 mm nominal outer dia Pipes

Providing and fixing brass bib cock of approved quality : 20 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 20 mm nominal outer dia Pipes

Providing and fixing JAQUAR MAKE, Pillar cock

White Vitreous China of 'Hindustan &Parryware' make or equivalent under counter type Oval wash basin of size 550 x 480mm with CI brackets suitable for mounting below granite counter including waste fitting with CP brass bottle trap, angle valve with CP connection etc as specified. Oval Wash Basin Model No.10051 OR consider equivalent make.)

Providing & fixing in position `Jacquar Continental' make CP Jet Spray with flexible CP supply pipe, and all other accessories,complete

White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend.

Providing and fixing in position uPVC/SWR (Soil/Waste/Rain) pipe of type-B 110 mm dia. in any position including all fittings and accessories, making joints / connections water tight with solvent cement, scaffolding if necessary and making good the damages if any (excluding excavation and refilling the trenches) etc. complete as specified and directed.(All fittings and accessories like clamps,etc. should be of same brand. No separate payment shall be made for fittings and accessories).

Providing & Fixing 100mm diameter Nahani trap Jali in steel finish with necessary fixing required to make the item well functional.

Single Door leaf finished with Green and environmental friendly and mould proof, high impact resistant ,crash proof, waterproof, chemical and stain resistant, flame retardant ,easy cleaning ,material do not contain heavy metals, such as lead, which has proven to be toxic FLAME SPEAD AND SMOKE:ASTM E84,CLASS A ,Class A fire rating. Surface burning characteristics, As determined ASTM E-84, shall be flame spread of 10 and smoke Fire rate:EN13501-1 and GB8624-2012

Double door: Providing and Installation of Door with frame : Double Door leaf finished with Green and environmental friendly and mould proof, high impact resistant ,crash proof, waterproof, chemical and stain resistant, flame retardant ,easy cleaning ,material do not contain heavy metals, such as lead, which has proven to be toxic FLAME SPEAD AND SMOKE:ASTM E84,CLASS A ,Class A fire rating. Surface burning characteristics, As determined ASTM E-84, shall be flame spread of 10 and smoke Fire rate:EN13501-1 and GB8624-2012

Aluminum alloy used in the manufacture of windows shall conform to IS designation HE 9-WP of IS:733. The sectional properties of extruded sections shall be as given in IS:1948 or as manufactured by approved manufacturer such as Jindal or approved by engineer in charge. The section shall be uniform in appearance, free from die lines and handling marks. Glass Panels shall be clear float glass panes with 5 mm thick. Glass panel shall weigh at least 7.5 kg/m2 and shall be free from flaws, specks or bubbles. All panes shall have properly squared corners and straight edges. The sizes of glass panes for use shall be in accordance with IS:1948 Screws and fasteners Screws and fasteners shall be of aluminum alloy or brass oxidized. Screw thread of machine screws used in the manufacture of aluminum windows

ELECTROCOOL ENGINEERING

Attharva Health Tech India Pvt. Ltd.