MTPS I OAHS AHPH II Breakdown repair works in the Ash slurry pumps High pressure water pumps Low pressure water pumps flush water pumps seal water pumps sump pumps cable trench pump

Amount

Charges for replacement of existing wornout oil seals in the non-drive end side of the Ash Slurry pump by removal of drive end assembly, replacing the and reassembling the same, belt tension and alignment works as directed by the Engineer in charge at site.

Charges for replacement of existing wornout spares/oil seal in the drive end side of the Ash Slurry pump by removal of suction & discharge spool pieces, suction side door, Suction side wear plate, suction flange, outer casing, inner casing, impeller, bracket side door, bracket side wear plate, gland housing, expeller, shaft sleeve, liquid thrower and belts, replacing the and reassembling the same, belt tension and alignment works as directed by the Engineer in charge at site.

Charges for replacement of existing worn out bearings in the pedestal assembly of the Ash Slurry pump by decouple the motor from the pedestal assembly, dismantling the bearing assembly, replacing the worn out bearings and reassembling the same, belt tension and alignment works as directed by the Engineer in charge at site.

Charges for dismantling the High pressure water pumps, Low pressure water pumps, flush water pumps or sump pump(A) by decouple the pump from the motor, dismantling the entire pump, replacing the worn out spares, reassembling and alignment works as directed by the Engineer in charge at site.

Charges for dismantling the cable trench pump, seal water pump or sump pump (B) by decouple the pump from the motor, dismantling the entire pump, replacing the worn out spares, reassembling and alignment works as directed by the Engineer in charge at site.

Charges for replacement of existing worn out NDE bearing in the High pressure water pumps, Low pressure water pumps, flush water pumps or seal water pumps by dismantling the bearing end cover, replacing the worn out bearing, reassembling and alignment works as directed by the Engineer in charge at site.

Charges for replacement of existing worn out DE bearing / shaft sleeves in the High pressure water pumps, Low pressure water pumps, flush water pumps or seal water pumps by decouple the pump from the motor, dismantling the pump, replacing the worn out bearing / shaft sleeves, reassembling and alignment works as directed by the Engineer in charge at site.

Charges for replacing the worn out (or) punctured M.S. spool piece by dismantling the sleeve joint, flange joint, dismantling the punctured M.S. spool piece, fabrication of new spool piece, erection and line joining work in the Ash slurry pipe lines in Ash handling pump house as directed by the Engineer in charge at site.

Charges for patch welding works in the worn out (or) punctured portion of the Ash slurry pipeline by dismantling the sleeve joint, flange joint, dismantling the punctured pipe line, half round patch welding work and line joining work in the Ash handling pump house as directed by the Engineer in charge at site.

Charges for dismantling the worn out (or) punctured 200 /250/ 300 NB valves, repairing and reassembling in the existing pipe lines in Ash handling pump house as directed by the Engineer in charge at site.

Charges for replacing the existing worn out 80 /100 / 200 / 250 / 300 NB valves in the Ash handling pump house as directed by the Engineer in charge at site.

Charges for replacing the existing worn out / punctured seal water line for Ash slurry pump, erection of new line and related valves in the Ash handling pump house as directed by the Engineer in charge at site.

Charges for replacement of damaged / worn out bearings in the ash slurry pumps including of de-coupling the pump from the motor dismantling of suction and delivery spool pieces ,outer casing ,bracket side, wear plate ,bracket side door ,impeller, dismantling of driven pulley from shaft, gland housing, liquid thrower inner and outer bearing caps etc.(Dismantling of ash slurry pump).

Reassembling of the ash slurry pumps.

Charges for dismantling the worn out(or) punctured MS ERW new bend and fabrication, erection by cutting and welding including cost of consumables such as cutting gas, welding electrodes, etc.. (300 NB)

Charges for welding of M.S. flanges with 300 NB MS ERW pipes and newly fabricated bends.

Charges for fabrication of M.S. flanges diaof OD490mm including cost for transportation to outside work shop and return.

Charges for patch welding works in the worn out (or) punctured portion of the ‘Y’ bend in the Ash slurry discharge pipeline by dismantling the ‘Y’ bend from the discharge valve, flushing valve, RC valve and sleeve joint, patch welding work and re-erection in the Ash slurry stream as directed by the Engineer in charge at site.(300NB)

Cost of Bearing No. 6311 Make: SKF

Cost of 19mm square PTFE Graphite Gland Rope

Cost of 12mm square PTFE Graphite Gland Rope

Supply of cutting gas

Supply of MS welding electrode

Charges for consumables hire charges for T&Ps

MEGALA ENTERPRISES (BID ID -1359198)