SPL REPAIR TO ORS MD ACCN BLDG. NO. P-48/01 TO P-48/08 AT NEW MH LINES OF MH, PROVN OF BARBED WIRE FENCING IN THE AREA OF OLD MH LINE AND YODHA GATE AT MATHURA UNDER GE(EAST) MATHURA

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/loose soil.

M&L for cement concrete type D2 1:4:8 using 40 mm graded aggregate as in foundation filling and mass concrete.

M&L for cement concrete Type B2 1:3:6 using 40 mm graded aggregate in foundation,filling and mass concrete all as specified.

S&F for MS work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and as directed.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) all as specified.

S&F Concertaina coil 450 mm dia with 2.50 mm dia high tensile strength wire fixing to Y-shaped angle iron posts securing with necessary clips on top of boundary wall all as specified and as directed.

M&L for preparation of new steel surfaces over 10 cm in width or girth and applying two coat synthetic enamel paint over a coat of zinc chromate primer complete all as specified.

Demolition of reinforced concrete (cutting reinforcement as required to facilitate demolation of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work all as specified.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing or removal from site complete all as specified and as directed.

Supplying & fixing steel tubing ,galvanised, medium grade 15 mm bore with all fittings and fixed complete to walls and ceiling or laid under floor complete all as specified and as directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth of brick walls complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing or removal from site complete all as specified and as directed.

Supplying & fixing steel tubing ,galvanised, medium grade 20 mm bore with all fittings and fixed complete to walls and ceiling or laid under floor complete all as specified and as directed.

Taking up or down 25 mm bore steel tubing and connections including cleaning for refixing or removal from site complete all as specified and as directed.

Supplying & fixing steel tubing ,galvanised, medium grade 25 mm bore with all fittings and fixed complete to walls and ceiling or laid under floor complete all as specified and as directed.

M&L for Precast SRFC manhole cover of size 0.60x1.20m heavy duty HD-20 laid on manhole complete all as specified and directed.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and as directed.

M&L for Brick work with old size fly ash Bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

Dismantling brick tiles any size laid bedded and pointed in any mortor.

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof)

M&L for 50 mm average thick PCC 1:2:4 type B0 (using 12.5 mm grd stone agg) in floors/padding finishing the surface even and smooth with out using extra cement.

M&L for bitumen felt water proofing treatment using APP based polymeric membrane minimum weighting 3kg/sqm and minimum thickness 3mm reinforced with polyster non wove fabric (but not less than 150gms/sqm) laid over bitumen primer applied @ 0.30 Kg/sqm by forced application complete all as specified and as directed.

M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L for roof cooling tiles 300x300x7mm thick set in neat cement slurry in floor over and including 15 mm thick screed bed in cement mortar 1:4 and filling the joints with Tile Max premium cementitious grout material of JK Cement or its equivalent complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for coloured Non skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchl aid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for light shade Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchl aid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for coloured Glazed ceramic tiles on vertical surface 600x300x7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match fixed over and including 10 mm thick backing coat of cement mortar in 1:4 complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness (except ceramic tiles) in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for single piece machine cut kota stone slab as in flooring 20-25 mm thick laid over and including 15mm thick screed bed in cement mortar 1:6 and jointed with gray cement mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for 16-18 mm thick Granite Z black slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like laid over and including 20mm thick screed bed in cement mortar 1:4 and pointing in white cement (1:2 )using marble dust with admixture of pigment to match with shade of granite, including rounded/half rounded edge and providing hole for gas pipe in pre-cast slab as well as in granite slab of cooking platform complete all as specified and as directed.

Taking down cement plaster on brick or stone walls,concrete surface etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L rendering 15mm thick on fair face of brick work/concrete in CM 1:4 and finishing surface even and fair by mixing liquid water proofing compound including two coats of Apex exterior emulsion paint over one coat of alkali resistant primer as per manufacturers instructions complete all as specified and as directed. Note :- Liquid WPC shall be measured & paid seprately.

Supply only liquid water proofing compound hydroseal-W+ /Dr Fixit or eqivalent (for plaster hardening, to contol efflorescence & fungal growth) as approved by Engineer-in-charge.

M&L for rendering 15 mm thick on other than fair faces brick wall or concrete surface in cement mortar 1:6 finished even & smooth without using extra cement complete all as specified and as directed.

M&L for 10mm thick rendering on fair faces of brick/concrte surface as in ceiling in cement mortar 1:3 finished the surface even and smooth without using extra cement and applying three coats of white wash on ceiling surface complete all as specified and directed complete all as specified and as directed.

M&L for preparation of new plastered surface of wall and applying providing one coat of wall care putty ,two coats of Oil Bound Distemper over and including one coat of alkali resistant primer on wall complete all as specified and directed by Engineer-in-Charge.

M&L for Complete removal of existing treatment of old surfaces on wall surfaces and applying two coat of oil bound distemper over one coat of wall care putty complete all as specified and directed.

M&l for preparation of old surfaces of wall and applying one coat of whitewash complete all as specified and directed.

Complete removal of existing treatement and applying two coats of exterior emulsion paint apex of asian or equivalent complete all as specified and directed..

S&F in repair 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repair 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repair 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F in repair 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F in repair 110 mm bore PVC (SWR) plain bends any radius complete all as specified and as directed.

S&F in repair 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F in repair 75 mm bore PVC (SWR) bends with access door any radius complete all as specified and as directed.

S&F in repair 110mm bore PVC (SWR) junction (Single T) equal or unequal complete all as specified and as directed.

S&F in repair 110mm bore PVC (SWR ) vent cowl complete all as specified and as specified.

S&F in repair PVC floor trap plain 75 mm dia of outlet with grating including jointing with solvent cement complete all as specified and as directed.

S&F long body bib taps cast copper alloy, chromium plated, fancy type with half turm handle having weight of bib tap should not be less than 450 gms for iron pipes15 mm bore dia complete all as specified and as directed.

S&F in repair stop valve/angular cock cast copper alloy, chromium plated, fancy type with crutch or butter fly handle, screwed down, screwed both end for iron pipes 15 mm dia bore complete all specified and as directed.

S & F in repairs Viterous china squatting pan, Órissa' pattern, size 580 x 440mm white, with integral foot rests including connection and fitting to trap, and to flushing pipe complete and making good to wall or floor tilling to match the existing complete all as specified and as directed.

S&F in repairs PVC (White) valve less syphonic action type, flushing cistern10 ltrs low level with inlet ball valve float, handle, aluminium brackets for bottom support fixing with gutties embeded in wall with drilling machine etc complete all as specified and as directed.

S&F in repair sinks with drainage board made of stainless steel 0lxmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repair vitreous china wash hand basin white flat back size 550 x 400 mm including brackets,waste fitting 32 mm brass chromium plated, incudig pillar tap cast copper alloy chromium plated, fancy type with capstan heads,screwed down high pressure,with or without letters Hot or Cold with long screwed shank and fly -nuts, screwed for iron pipe 15 mm bore dia complete all as specified and as directed.

S&F Swivel CP shower of size 200 mm for fixing with 15mm pipe (minimum weight 40gms) complete all as specified and as directed.

S&F Shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (minimum weight 40gms) complete all as specified and as directed.

Supply and fix in repair 500 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm bore dia complete all as specified and as directed. Make:-Sintex Pure,Vactus Smart,Supreme White.

S&F in repair Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes 20 mm bore dia complete all as specified and as directed.

S&F in repair PVC connections 15 mm size with PTMT nuts at both end of 600 mm long complete all as specified and as directed.

S&F in repairs high density polythene pipe 32 mm bore (HDPE) of pressure @ 6 Kg/Sqcm laid in trenches complete all as specified and as directed.

S&F in repair stainless steel kitchen plate rack of size 31" x 30" x 10" deep, fabricated with 0.63 mm sheet fixed in position on wall complete all as specified and as directed. Make : Prayag cat No P-346 or equivalent of make approved by GE

S&F in repairs stainless steel towel rail 600 mm long 20 mm dia fixed with steel screw etc complete all as specified and as directed.

S&F in repair sheet glass shelf assembly consiting of 5.5 mm sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F in repairs corner glass with glass of size 300x300mmx8mm thick, bevelled on edges with two brackets CP complete all as directed.

M&L for 50mm thick sand stone slab set and jointed over supports as in chajjas of ground and first floor's over windows, doors etc and jointed in cement mortar 1:4 complete all as specified and as directed.

M&L for 25 mm average thick PCC 1:2:4 type B0 (using 12.5 mm grd stone agg) in floors/padding finishing the surface even and smooth with out using extra cement.

S&F MS Joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated)

S&F in repair stainless steel fancy type curtain rod 20 mm dia ,chromium plated with fixing brackets, incl side brackets, complete complete all as specified.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 100 mm thick cement concrete type-D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed.

M&L for sand filling under floors or in foundations incl watering and consolidation complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block with grey cement and no pigments any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 Grade complete all as specified and as directed.

M&L for 50 mm thick cement concrete 1:3:6 type C1 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and fair without using extra cement complete all as specified and as directed.

M&L non skid coloured cermic ENDURA tiles 400x400x15mm thick set and jointed in neat cement slurry & pointed with coloured cement to match in floor over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames not exc. 1.5 sqm each complete all as specified and as directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames exc. 1.5 sqm but n exc 4 Sqm each complete all as specified and as directed.

S&F Solid WPC Door Frame of size 50mm x 47mm complete all as specified and as directed.

S&F 30 mm thick factory made WPC door with both side lamination complete all as specified and as directed.

S&F Pressed steel frames of size 105x60 mm made out of 2.00 mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete as specified and as directed.

S&F Pressed steel frames of size 125x60 mm made out of 2.00 mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.with one shop coat of red oxide primer complete as specified and as directed.

M&L for cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in bed blocks for fixing hold fasts and filling of chowkhats etc complete all as specified and as directed.

M&L for prepration of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over primed surface complete all as specified and as directed.

S&F 35 mm thick factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc without sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-1 section 8 clause 8.24 (a) complete all as specified and as directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as spicified and as directed.

S&F 30 mm thick factory made flush shutters, solid core construction with block board core and plywood face panel veneer type on both side complete all as specified and as directed.

S&F Stainless steel handles of size 150 mm, fabricated type anodised complete all as specified and as directed. Make Global,Hettich,Plantex

S&F Stainless steel barrel tower bolts 200 mm length of bolt of extruded section and fixed complete all as specified and as directed. Make Global,Hettich,Plantex

S&F Stainless steel 250 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of stainless steel and fixed complete all as specified and as directed. Make Global,Hettich,Plantex

S&F 100 mm long size of hinges, extruded aluminium alloy with galvanised mild steel hings pin anodized and fixed type B-21complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F MS Framed work such as grills gratings, door and cooler stand, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars and similar work confirming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for powder coated aluminium frame for doors, windows, ventilators ( minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified including power coating.

M&L for powder coated aluminium casement window shutters (incl both glazed and Jali window) (powder coating shall not be less than 50 microns of approved colour) side hung type with and without sash bars, aluminium sections weighing 0.75 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

S&F 5 mm thick sheet glass, ordinary quality and fixing with rubber beading area n exc. 0.5 square metre in each pane etc complete all as specified and as directed.

S&F aluminium anodized barrel tower bolts 75 mm length of bolt of extruded section and fixed complete all as specified and as directed.

S&F floor door stopper of aluminium anodised body and tengue, anodised with hard drwan steel spring overall length of cover plate 140 mm complete all as specfied and as directed.

S&F 300 mm size mild steel rat tail rod pattern door springs ISI marked including roller & roller plate etc complete all as specified and as directed.

M&L for providing cement concrete type B0 1:2:4 (using 12.5mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L for 10 mm thick polymer modified plaster in CM 1:4 mixing the polymer in the ratio of 1:10 (1 part of polymer & 10 parts of cement) for sides and base of sunken floor portion. Note:-Make of polymer Asian Paints/Pidilite/STP/Thermax/Sico

M&L for cement concrete 1:7:12 type F2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

S & F 18 mm thick WPC board both side decorative fixed with screws, solvent cement/ adhesive/bolts to make kitchen cabinet sides top and bottom and shelves inside the cabinets etc. complete as per specifications and as directed.

S & F 16 mm thick WPC board having density of board 575 to 600 Kg/cum) of Single Side Prelam/ Rigidlam color fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by the Engineer - in -Charge.

S & F 12 mm thick WPC board having density of board 575 to 600 Kg/cum) of plain white(Matt finish) color fixed with screws, solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per specifications and as directed by the Engineer - in –Charge.

S&F in 100 mm size aluminium anodised Hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S & F auto closing hinges 35 mm of 0 crank( KH-001)OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters -(Make- KAFF, Godrej & Hettich)

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m deep for foundations, manholes sewage line, laying of cable etc and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in excavated soil including spreading, levelling,watering and well ramming in layers not exceeding 25 cm thick each complete all as specified and as directed.

Removal of excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Demolition and breaking up 150 mm internal dia drain pipe (salt glazed ware, AC or reinforced cement concrete) set in cement mortar including cement concrete bedding and haunching and removing the demolished material out of MoD land complete all as specified and as directed.

M&L Cement concrete 1:4:8 Type D-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm internal dia pipe complete all as specified and as directed.

M&L for reinforced concrete pipes, class NP-2, 150 mm bore grade 'A', with collar laid in trenches and jointed with cement mortar 1:1 complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B2 (using 40 mm graded stone aggregate) as in surface drain, benchings etc complete all as specified and as directed.

M&L for built in steel cup board with pressed steel frame of size 75mmx45x1.25 mm thick with pressed steel shutter 1 mm thick Godrej pattern fixed to masonary wall by hold fast made out of 25x3 mm flat iron including MS hanging rod of 10 mm dia with bracket fixed on inner side of one leaf of shutter and on the other leaf provision of MS peg set of three pegs including spray incl locking arrangement painting with two coats of synthetic enamel paint over one coat of red oxide primer all around on steel surface of frame and shutter and making good disturbed portion in CM 1:3 or PCC 1:2:4 complete all as specified.

Supply for Pipe Supporting Clamping - Single Pipe of dia 110 mm (4") down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 75 mm (3"): Pipe Support Clamping made of : 1. Profile Bracket having Wall Distance 75 mm (3") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 250 mm (10") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 75 mm (3") - 2 Nos. 2. Continuous Slotted C Channel of Size 250 mm (10") - 1 No.; 3. U Bolt Rubber sleeve mounted for 110 mm (4") CI or PVC Pipe Dia. - 1 No.; and 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jaipur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : TD/2022/01 and TD/2024/02. Make: Shaivi or equivalent as approved by GE.

Supply for Pipe Supporting Clamping - Single Pipe of dia 75 mm (3") down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 75 mm (3"): Pipe Support Clamping made of : 1. Profile Bracket having Wall Distance 75 mm (3") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 250 mm (10") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 75 mm (3") - 2 Nos. 2. Continuous Slotted C Channel of Size 250 mm (10") - 1 No.; 3. U Bolt Rubber Sleeve mounted for 75 mm (3") CI or PVC Pipe Dia. - 1 No.; and 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jaipur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : TD/2022/01 and TD/2024/02. Make: Shaivi or equivalent as approved by GE.

Supply for Pipe Supporting Clamping - Single Pipe of dia 20 mm (3/4") down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt Rubber Sleeve mounted system running vertically with wall distance 75 mm (3"): Pipe Support Clamping made of: 1. Mono Bracket for 20 mm (3/4") pipe having Wall Distance 75 mm (3") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. 2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 20 mm (3/4") pipe, Wall distance 75 mm (3") - 1 Nos. 2. U Bol Rubber Sleeve mounted for 20 mm (3/4") GI / UPVC/ CPVC pipe Dia. - 1 nos and 3. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jaipur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : TD/2022/01 and TD/2024/02. Make : Shaivi or equivalent as approved by GE.

Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc) complete including fixtures & fittings (such as ceiling rose, socket, Pendent, regulator, light fitting etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as directed. (Note: Credit for above items should be made as per credit Schedule separately)

M & L for Point wiring for One light point/Fan point controlled by one switch 5 amp with 1.5 Sqmm (nominal area) single core PVC insulated Sheathed (FRLSH) cable, multi-stranded, copper conductor, in universal colour code with & including suitable size of rigid non-metallic PVC conduit (not less then 20mm dia med gd)and its all accessories complete concealed in wall incl cutting & chases( making good all to the disturbed surfaces as per existing) and modular flush metal boxes including cover plate with frame for mounting modular switches, sockets, regulators,socket etc including earth wire of PVC insulated (FRLSH) copper conductor multistranded of 1.5 Sqmm size in green colour complete all as specified in current SSR Part-I & II & directed by the Engineer-in-Charge.

All as per item No. 123 here-in-above but for One 3 pin socket outlet 5 amps point controlled by one switch on same board.

All as per item No. 123 here-in-above but for One 3 pin socket outlet 5 amps point controlled by one switch, Independent board.

All as per item No. 123 here-in-above but for One bell point controlled by one Modular push button on independent board

All as per item No. 123 here-in-above but for One light point controlled by two way switches, with cables 1.5 sq. mm size

All as per item No. 123 here-in-above but for 3 pin/ 5 pin, sockets outlet,15 amps with 4.0 sqmm PVC insulated & Sheathed (FRLSH) cable, independent, Point wiring

M&L ceiling rose, PVC / polycarbonate, isolated body 65mm x 50mm three terminals

Supply and Fixing Modular switch 6 Amps single pole one-way, 1 Module.

Supply and Fixing Modular switch 16 Amp single pole one way, 1 Module.

Modular switch 2 way 6A,1 module

Supply and Fixing Modular bell Push switch 6 Amps with indicator single pole one-way, 1 Module complete.

Supply and Fixing Modular socket 2-in-1, 5 pins 6 Amps, combined 2 Module complete.

Supply and Fixing Modular socket 2-in-1, 3 and 5 pins 6 /16 Amps, combined 2 Module.

Supply and Fixing Modular fan Regulator electronic step type 120 watt, 2 Module complete.

Supply and Fixing Bell, Ding Dong, AC, single pole

Supply and Fixing Lamp holder, PVC/ Polycarbonate type with back plate suitable for batten

Supply and Fixing Blukhead IP65 10 watt

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1x 20 watt LED Tube fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1x 10 watt LED Tube fitting (size within 600x25x40 mm) suitable for mirror light with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K,>100Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lamp, 9 watt, B-22 base complete.

S&F Decorative wall light made up of high grade engineering plastic material suitable for 9 W LED lamp B22 base. Note: 9 watt led bulb will be measured and paid seperately.

Supply and install of 35W LED building security light fitting with lens & driver, powder coated pressure die cast aluminium, top opening and maintainable with heat resistance toughened glass, built-in Short-Circuit Protection, Over voltage Protection and Surge Protection, IP-65 proction with luminaire efficiecy of greater than 80Lumen/Watt, Colour rendering (CRI) of ≥ 70 and co- related colour temperature (CCT) of 5700K (±500K) . The luminaire should have 10 KV surg protection, PF ≥ 0.9 and total harmonic distortion of THD ≤ 10%, voltage range of 140-280V including all connections complete all as specified.

M&L for building security light bracket made out of 40mm dia light grade GI pipe of

Taking down of MCB DBs/ sheet metal enclosure with MCB's/MCCB's

S&F MCB distribution board, SPN 12 way, Double door, sheet steel, phosphatised, powder painted with Copper bus-bar 200Amp, neutral link, earth bar and din rail , cable ties for cable management, 240 V, complete all as specified.

Supply & fixing powder coated CRCA steel sheet MCB distrbution board, IP-43 IK-09 protection, double door recess mounted, triple pole and neutral 4 way complete.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB), TPN 40-100 Amps, complete with connection

Supply and fixing 240V, 10KA 'C' curve miniature circuit breaker (MCB), SPN 32 amps complete with connection

S&F MCB SP, 5-32 Amps, 'C' series, breaking cap 10 kA, 240V

Taking down electric meter from location and refixing the same on LT Panel/ Wall as per existing location with nut, bolts and all electrical connection from the DBs with suitable thimbles including making connection complete all as specified. NOTE: connection cable 10 sqmm multistranded copper conductor with flexible pipe main DB to meter deemed to included in quoted rate nothing paid extra.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V,1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) controlled by remote control all as specified and directed by Engr-in-charge Note: Old fan should be deposited in MES store.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm Note: Old fan should be deposited in MES store.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers Note: Old fan should be deposited in MES store.

Cutting holes for air ducting of exhaust fan in Circle / square shape or as per site

Taking down carefully by Submain wiring/ service connection of any type

M & L for Sub Main Wiring for DB to DB with two runs single core 10 Sqmm PVC insulated Sheathed (FRLSH) cable with stranded copper conductor drawn in suitable size of rigid non-metallic PVC conduit and its all accessories complete concealed in wall/roof with and including 10 Sqmm copper green colour earth wire all as specified and directed by Engineer-in-Charge.(02 run 10 Sq mm single core cable, one run of 6 Sq mm earth wire & One run of PVC conduit will measured as one RM).

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core, laid in trenches / duct / fixing on walls / poles or passing through HDPE double wall corrugated pipe (outer dia should not be less then 40 mm) including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole / Main Panel Box and testing complete all as specified and directed. Note:- HDPE pipe rate shall be deemed in quoted rate above.

M&L for earthling complete with galvanized steel earth plate eletrode 60x60 cm x6.3 mm thick burred directly in ground (earth pit not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 Metrs below normal ground level connected to galvanized earth lead wire 4.00mm dia by means of bolts, nuts check nuts and washers of galvanized iron or steel all as shown in electrical plate No.5 connected to earthling test point all as specified and indicated including testing on completion including excavation and arth work PCC pit & RCC pit over funnel with watering pipe wire mesh GI protection pipe etc complete.

Taking out the electric geyser of capacity 25 Ltrs Ltrs carefully from its installed position by disconneting inlet and outlet water pipes, dismantling the unit and replacing the defective Parts and painting with one coat of synthetic enamel paint and witing MES No.and safely keeping a side & refixing in its original position after completion of civil work and reconnecting the inlet/outlet water pipes and testing on completion complete all as directed by Engr-in-Charge. NOTE:- The spare parts required shall be measured and paid separately under relevant items.

Supply only Heating element 1.5 / 2 KW ISI marked including rubber Gasket as per existing type.

Supply only Thermostat suitable for 25 Ltrs Geyser (as per the existing type).

Supply only Hot water / cold water pipe 600mm long as per existing type.

S&F AC Box With 20A SP MCB, Metal Enclosure

Deepak Saxena (BID ID -3495645)

BS CONSTRUCTION (BID ID -3495162)

Shiva Traders (BID ID -3503708)