Provision of Civil Works for Construction of Office Cum Training Building and Residential Accommodation for Officers and Staff of National Academy of Defence Financial Management NADFM Pune

Amount

SUB HEAD- I _DEMOLITION & DISMENTALING

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work

Credit for structural steel obtained from Item 1.02, 1.05 & 1.06

Dismantling barbed wire or flexible wire rope / GI Chain link fencing including making rolls and stacking within 50 mtr.s lead.

Dismantling and stacking within 50 mtr.s lead, fencing posts or struts including all earth work and dismantling of concrete etc. in base of: T' or 'L' iron or pipe

SUB HEAD II : EARTH WORK & EXCAVATION

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. Note : No additional payment will be made for extra lift for mechanical Excavation All kinds of soil. a) lift upto 1.5 m

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. Note : No additional payment will be made for extra lift for mechanical Excavation Ordinary rock a) lift upto 1.5 m

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains not exceeding 1.5m in width or 10 sqm on plan including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m. Note : No additional payment will be made for extra lift for mechanical Excavation Hard rock (blasting prohibited) a) lift upto 1.5 m

b) Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. ( For manual means)

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. Note : No additional payment will be made for extra lift for mechanical Excavation All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. Note : No additional payment will be made for extra lift for mechanical Excavation Ordinary rock

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed. Note : No additional payment will be made for extra lift for mechanical Excavation. Hard rock (blasting prohibited)

Credit for hard rock obtained from Item No. 2.03 & 2.07 above.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supply and laying of approved earth obtained from borrow pits outside MD land and filling in layers not exceeding 20 cms thick, at all heights and depths, in foundation pits, trenches, around structures and foundations, underfloors and other places, including watering, consolidating each layer in filled up area by rolling and compacting with roller/ plate compactor as required to achieve not less than 97% modified proctor density conforming to relevant IS etc. The rate includes necessary soil testing charges at laboratory & field as per relevant I.S. codes . complete as directed by Engineer In charge.

Filling in area, plinth, floors, trenches, pits with approved excavated materials, good earth available within the site premises in layers not exceeding 200mm including breaking of clods, watering, consolidating each layer in filled up area by rolling and compacting with roller/ plate compactor as required to achieve not less than 97% modified proctor density conforming to relevant IS etc. The rate includes necessary soil testing charges at laboratory & field as per relevant I.S. codes . complete as directed by Engineer In charge.

Providing & Laying dry stone Rubble Soling of with average thick 230 mm size hard stone set in regular lines, handpacked and interstices thoroughly filled with small chips including filling in with good quality murum brought from outside, compacting with iron rammers, watering, sand spreading 12mm thk. layer of grit on top etc complete as directed by Engineer In Charge. (Note: The rate includes the royalty and other taxes if any)

Extra for additional lead over 50m up to 1.00 Km for carraige of excavated soil & ordinary rock by mechanical transport including loading, unloading & stacking etc. complete. (For Item No. 2.01,2.02,2.05,2.06 and except for the quantity of item No.2.09)

SUB HEAD III : ANTI-TERMITE TREATMENT

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

SUB HEAD IV : PLAIN & REINFORCED CEMENT CONCRETE

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size).

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

Providing and laying in position ready mixed or site batched design mix cement concrete M-25 grade cement concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural source, Portland pozzolana / Ordinary Portland/Portland Sag cement, admixture in recommended proportion as per IS 9103 to accelerate or retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads but excluding the cost of centering, shuttering, finishing and reinforcement as per the direction of engineer in charge, for the following grades of concrete. Note :- Extra Cement up to 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 110% of the spefified minimum cement content, the contractor shall have discretion to either redesign the mix or bare the cost of extra cement.

All works upto plinth level. concrete of M-25 grade with minimum cement content of 330 kg /cum

All works above plinth level. concrete of M-25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete M-30 grade cement concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural source, Portland pozzolana / Ordinary Portland/Portland Sag cement, admixture in recommended proportion as per IS 9103 to accelerate or retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads but excluding the cost of centering, shuttering, finishing and reinforcement as per the direction of engineer in charge, for the following grades of concrete. Note :- Extra Cement up to 10% of the minimum specified cement content in designmix shall be paid separately. In case the cement content in design mix is more than 110% of the spefified minimum cement content, the contractor shall have discretion to either redesign the mix or bare the cost of extra cement.

All works upto plinth level. concrete of M-30 grade with minimum cement content of 350 kg /cum

All work above plinth level upto floor V level concrete of M-30 grade with minimum cement content of 350 kg /cum

Extra for RCC / BMC/RMC work above floor V level for each four floor or part thereof

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. & above plinth at all levels a)Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Weather shade, Chajjas, corbels etc., including edges

Small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the like

Stairs, (excluding landings) except spiral-staircases

Cornices and mouldings.

Extra over Item No. 4.16 & 4.17 for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of Stone aggregate 40 mm nominal size, well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing : 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Providing and placing in position 100mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes,of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage ,all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforcedwith 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 50 mm thick

SUB HEAD V : STONE & BRICK MASONRY

Providing random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level including cost of bond stones as required with : Cement mortar 1:6 (1 cement : 6 coarse sand).

Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. Including cost of bond stones as required: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry with 150mm / 200mm / 230mm/300 mm thick with Grade - 1 AAC blocks of density 551 to 650 kg/cum confirming to IS:2185 (part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm/ 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

Brick work with clay flyash F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor five level in. Cement mortar 1:4 (1 cement : 4 coarse sand).

SUB HEAD VI : PLASTERING & SURFACE TREATMENT

Providing external plaster 12 mm thick on concrete or brick or AAC block surfaces with Readymix plaster (Ultratech Readyplast Projekt, Magicrete Redimix Plaster, or equto) etc complete at all levels,lead and lifts with necessary scaffolding, curing, etc. as per direction of Engineer-in-Charge. Note: Work is to be executed through an authorized applicator of the manufacturer, and approval of the same must be obtained from the Engineer in Charge

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturer.

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Providing and applying 6 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Providing 6 mm thick plaster for ceiling & bottom surfaces (concrete or brick or AAC block surfaces) with Readymix plaster (Ultratech, Magicrete Redimix Plaster, or equivalent ) etc complete at all levels,lead and lifts with necessary scaffolding, curing, etc. as per direction of Engineer-in-Charge. Note: Work is to be executed through an authorized applicator of the manufacturer, and approval of the same must be obtained from the Engineer in Charge

Extra for 12 to 20mm wide and 6 to 12mm in depth forming groove in plaster including scaffolding, finishing, curing etc complete as directed By Engineer In Charge. (Paid only for architectural / elevation grooves)

18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement : 4 fine sand): a) Raised Band

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) Note: Work is to be executed through an authorized applicator of the manufacturer, and approval of the same must be obtained from the Engineer in Charge

Finishing walls with textured exterior paint of required texure & shade : One coat of exterior promer (@ 1.67 ltr/10 sqm) + 1 coat of texure ( @ 16.4 Kg/ 10 sqm or as per manufacturer) + 2 coates of Acrylic exterior Paint (@ 1.67 ltr/10 sqm) including Scaffolding / Gandola etc complete at all level & height and as directed by Engineering Incharge Note: Work is to be executed through an authorized applicator of the manufacturer, and approval of the same must be obtained from the Engineer in Charge

Finishing walls with textured exterior paint of Red Brick Pattern texure & shade : One coat of exterior promer (@ 1.67 ltr/10 sqm) + 2 coat of texure ( @ 16.4 Kg / 10 sqm per coat or as per manufacturer) + 2 coates of Acrylic exterior Paint (@ 1.67 ltr/10 sqm) including Scaffolding / Gandola etc complete at all level & height and as directed by Engineering Incharge Note: Work is to be executed through an authorized applicator of the manufacturer, and approval of the same must be obtained from the Engineer in Charge

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Providing and fixing GI plaster mesh of nominal thickness 0.35 to 0.40 mm with zinc coating of 120 gms per sq m of approved make. all as directed.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. a) Height 10 m to 13 m

b) Height 13 m to 16 m

c) Height 16 m to 19 m

d) Height 19 m to 22 m

e) Height 22 m to 25 m

f) Height 25 m to 28 m

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade a) New work (two or more coats) over and including water thinnable priming coat with cement primer.

Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Applying priming coat : With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work.

French spirit polishing :Two or more coats on new works including a coat of wood filler

Supply and Installation of fabric backing Wall Paper of approved shade with recommended adhesive of approved make which have 100% washable, scratch resistance, peel proof, and fire retardant properties. The wall paper should give a seamless finish. Cost to include preparation on the punned surface for receiving the wall paper as per the manufacturer specification etc complete as instructed by Engineer in Charge

Providing and fixing Glass Fiber Reinforced Concrete (G.F.R.C) Half Round Columns with base, Capitol and Main body of Required Diameter , design cum height as per architectural drawing and approved shade . The Columns should be made from ‘53 grade’ White Portland Cement manufactured by ‘JK Cement’ or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by 'NEG Japan, Owen Corning ‘Saint Gobain’ or equivalent, Super Plasticizers manufactured by ‘Silk Root, Korea’ or equivalent, Polymers manufactured by ‘Pidilite’ or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by ‘BAYFERROX (Germany)’ or Lanxess or equivalent. The material casting should take place in FRP Mold with 'Power Spray machine' with Spray Mix design methodology. The erection of screens should be done with 'Dry Fixing method on to structural support members i.e. RCC, Brick work or M.S with Hilti or Fischer fasteners or Microtek Self Tapping screws. The quantity of fasteners or self-tapping screws shall be calculated in accordance to weight of Column. Including Steel fabricated structure for Supporting the GFRC columns, either integrated with GFRC columns or Installed separately as per site feasibility. Vendor shall submit shop drawings of same, duly approved from Engineer in charge.

Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : Flush/ Ruled pointing

Providing 12 mm thick plaster using machin spray on concrete or brick or Fly ash brick surfaces with Readymix plaster (Ultratech Readymix Plaster, Magicrete Redimix Plaster, or equtivalent) etc complete at all levels,lead and lifts with necessary scaffolding, curing, etc. as per direction of Engineer-in-Charge. Note: Work is to be executed through an authorized applicator of the manufacturer, and approval of the same must be obtained from the Engineer in Charge

SUB HEAD VII : FLOORING

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size

a) Size of Tile 600 x 600 mm

b) Size of Tile 600 x 1200 mm

c) Size of Tile 800 x 1600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Double charge vitrified tile polished finish of size

a) Size of Tile 600 x 600 mm

b) Size of Tile 600 x 1200 mm

c) Size of Tile 800 x 1600 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade,laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 X 600 mm

Providing and laying Glazed Vitrified tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying full body vitrified tile in floor of minimum thickness 15 mm with water absorption less than 0.06% and conforming to IS: 15622, of approved make, brand and manufacturer, laid on 20mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand ) jointing with gray cement slurry @ 3.30 kg / sqm inlcuding grouting the joint with white cement and matching pigments etc. The slab must be cut with white cement and matching pigment etc. The slab must be cut with zero chipping diamond cutter only. laaying of slab will be done with the help of notch , trowel , wedge, clip of required thickness , vacuum cups for lifting, leveling system and rubber mallet for placing the slab gently and easily. Size of tile 800 X 2400 mm of all colours and shades.

Providing and laying full body vitrified tile in floor of minimum thickness 15 mm with water absorption less than 0.06% and conforming to IS: 15622, of approved make, brand and manufacturer, size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying anti skid full body vitrified tile in floor of minimum thickness 16 mm with water absorption less than 0.06% and conforming to IS: 15622, of approved make, brand and manufacturer, laid on 20mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand ) jointing with gray cement slurry @ 3.30 kg / sqm inlcuding grouting the joint with white cement and matching pigments etc. The slab must be cut with white cement and matching pigment etc. The slab must be cut with zero chipping diamond cutter only. laying of slab will be done with the help of notch , trowel , wedge, clip of required thickness , vacuum cups for lifting, leveling system and rubber mallet for placing the slab gently and easily. Size of tile 100 x 100 mm of all colours and shades.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conformingto IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. a) Size 300mm X 600mm

Providing and fixing glass mossaic tiles on finished plain wall surface of size 20mm X 20mm X 4mm in all colour , design, fixing in customize design as per direction of Engineer - in - charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by engineer - in - charge.

Providing and laying machine cut, mirror polished Marble stone flooring , in required design (Simple geometrical, abstract etc.) and in patterns in combination with italian marble stones of different colour , shades and finished surface texture etc. in linear portions of the building , all complete as per the architectural drawings, with 18mm thick stone slab laid ovedr 20mm (Average) thick base of cement mortar 1:4 ( 1 Cement : 4 course sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade , including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer-in-charge. 18mm thick italian marble stone slab, periato, Rossa verona, Fire Red or Dark Emperadone etc.

Providing and laying machine cut, mirror polished 18 mm thick italian Marble stone flooring for in skirting or riser of step, matching with the flooring including under a layer of 12mm thick CM 1:3 (1 cement : 3 coarse sand), jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand). 25 mm thick.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing 8-9mm thick Laminated wooden flooring of standard commercial grade (AC4), composed of water repellant HDF panels with direct preassure laminate and protective laminate based abrasion resistant film etc complete including underlay(Polyethylene sheet), floor transition strips , profiles,and all accessories as required

Supply and installation of approved quality 4mm thick synthetic PVC sports flooring for badminton courts, compliant with IS 15475:2018 standards for friction and IS 14462:1997 for shock absorption. The flooring will feature a multi-layered design, offering high friction and resistance to rolling loads, ensuring a safe and optimal playing surface. Included in the installation is a minimum 5mm thick shock-absorbing underlay with a density of ≥ 200 kg/m³, to enhance player comfort and floor resilience. Installation will be carried out using high-performance, low-VOC adhesives as per IS 15477:2019, with seams welded or taped to ensure a seamless finish. The subsurface will be prepared to ensure it is clean, dry, and level, with a flatness tolerance of ±2mm over 2 meters as per IS 2571:1970, and a moisture barrier applied if necessary, following IS 3316:1999. The flooring will be finished with matching edge trims for a neat appearance. The flooring will be provided in a designated color, typically green with standard white court markings, compliant with BWF standards etc complete as directed by Engineer in Charge. Note: A detailed maintenance guide is to be submitted.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18mm thick stone slab over 20 mm (avrage) thick base of cement mortor 1:4 ( 1cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing, and polishing etc all complete as specified and as directed by the engineer- in- charge. Flamed finish granite stone slab jet Balck, cherry red , Elite Brown , cat eye or equivalent

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills ,facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red. a) Area of slab over 0.50 sqm.

b) Area of slab up to 0.50 sqm.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Extra for granite/marble stone flooring in treads of steps and risers using single length up to 2.00 metre.

Extra for pre finished nosing to treads of steps of granite stone/Marble .

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm nominal size stone aggregate.

Cement plaster skirting (up to 30 cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement. 18 mm thick.

SUBHEAD VIII : STEEL AND WOOD WORK

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367: Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge.

Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875 Part 3 - ii) Sites with structure height more than 20m for all wind speeds. a) Two track two panel sliding window with aluminium channel for roller track , wood pile, nylon with SS 304 body

Using R2 series with frame ( 40 mm& Above) x (40 mm & above) & sash (25mm & above) X ( 50mm & Above) with zinc alloy (Zemak) powder coated touch lock with hook (Height upto 1.2m)

Using R3 series with frame ( 55mm & above) X (40 mm & above) & Sash (30mm & above) X (55mm & above) with zinc alloy (zamak) powder coated handle on every panel along with ,ulti-point locking system (Height upto 1.8m)

b) Three track three panel sliding window with two glazed & one S S wire mesh panel with aluminium channel for roller track, wool pile,nylon rollers with SS 304 body

Using R2 series with frame (70mm & above) X (40mm & Above) & both glazed and fly screen sash( 25mm & above) X (50 mm & above)with zinc alloys (Zamaj) powder coated touch lock with hook . (Height upto 1.2m meter)

Using R3 series with frame (98mm & above) X ( 40mm & above) & both glazed and fly screen sash ( 30mm & above) X ( 55 mm & above) with zinc alloy (Zamak) Powder coated handle on every glazed Panel along with multi-point locking system (height Upto 1.8 m)

c) Ventilator casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (Zamak) powder coated handles. Using R1 series with frame ( 33mm & above) X (35mm & above) & sash/mullion (33mm & above) X (50mm & above).(Heigth upto 0.9 m)

d) Casement window double panel with fixed mullion with S.S 304 friction hinges as per size and weight of sash, multi-point locking system,zinc alloy (Zamak) powder coated handles. i) Using R2 series with frame (39mm & above) X (39mm & above) & sash (39mm & above) X (60mm & above). (Height upto 1.2 m)

ii) Using R3 series with frame ( 55mm & above) X (45mm & above) & sash ( 55mm & above) X ( 65mm & above). (Height upto 1.8 m)

e) Three track three panel sliding window with aluminium channel for roller track , wood pile, nylon with SS 304 body i) Using R2 series with frame (70mm & above) X (40mm & Above) & fly screen sash( 25mm & above) X (50 mm & above)with zinc alloys (Zamak) powder coated touch lock with hook . (Height upto 1.2m meter)

ii) Using R3 series with frame (98mm & above) X ( 40mm & above) & sash ( 30mm & above) X ( 55 mm & above) with zinc alloy (Zamak) Powder coated handle on two end Panel along with multi-point locking system (height Upto 1.8 m)

Providing and fixing glazing in aluminium/UPVC door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. a) Float glass panes of nominal thickness 5 mm (weight not less than 12.50 kg/sqm)

b) Pin headed glass panes of nominal thickness 5 mm (weight not less than 12.50 kg/sqm)

c) fly proof stainless steel grade 304 wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing to existing door frames. 30mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.(Including internal lipping)

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. (Including internal lipping)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge. (The rate shall includes all necessary fittings i.e. Floor springs, Patch fittings, SS Door handle, lock and stopper etc. of approved make).

Providing and fixing 2mm thick M.S. sheet door with frame of 50x50x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 50x50x6 mm for diagonal braces

Providing and fixing pressed steel door frames conforming to IS: 4351 manufactured from commercial mild steel sheet of 1.60 mm thickness including jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.60 mm pressed mild steel welded or rigidly fixed together by mechanical means, including 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

a) Profile C Fixing with adjustable lugs with split end tail to each jamb

b) Profile E Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : Size 125 x 64 x 1.9 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : Size 150x10 mm

Size 200x10 mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 100mm long

125mm long

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm) with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : a) 300x16 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : a) Size 100x10 mm

b) Size 200x10 mm

Providing and fixing bright finished brass handles with screws etc. complete: a) 100mm long

b) 125mm long

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square

Providing and fixing of Magic Eye in all type of flush door as per instruction of Engineer In Charge.

Providing and fixing of Stainless Chain latch in all type of flush door as per instruction of Engineer In Charge.

Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality).

Providing and fixing at all height wall panelling with phenol bonded Bamboo Mat board conforming to IS:13958-1994 including providing and fixing to frame work made of 50mm x 50mm hardwood plugs including cutting brick work and fixing in cement mortar and making good the wall etc. and also providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws all complete as per direction of Engineer-in-Charge. 9 mm thickness

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and fixing 18mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge (Note: Fittings to be paid separately). 18 mm thick

Providing and fixing 6mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge.

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineerin-charge.(Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in-charge.

Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge. 200 mm

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic 734 type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-incharge.

Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in-charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately)

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-charge.

Providing and fixing Cupboard 600mm deep made out of 19mm thick commercial ply in shutters, selfs, sides, top & bottom, drawers etc., 8mm thick commercial ply on back, decorative laminate 1mm thick of approved make on all external exposed surface & edges to have 6mm thick teak lipping and finsihed with melamine polish, inner exposed surface finished with paint of approved shade including all necessory hardware & fittings i.e. lock, magnetic catcher, handles etc. all complete as per drawing.

Providing Cupboard shutters made out of 19mm thick commercial board with decorative laminate 1mm thick of approved make on external exposed surface & edges to have 6mm thick teak lipping and finsihed with melamine polish, inner exposed surface finished with paint of approved shade , including all necessory hardware & fittings i.e. lock, magnetic catcher, handles etc. all complete as per drawing.

Providing and Fixing of Stainless steel Drapery Rods (curtain rods) of 25 mm dia along with all accessories such as Curtain ring (nos. sufficient for rod length) , Holding Bracket, Finials (End capping), screws, fissures etc. Including fixing of same in matching shades as per sample approved of quality ,colour and shade including all fittings/fixtures etc all complete. All as per direction of Engineer-in-Charge.

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately).

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparentor dyed to required shade according toIS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium/UPVC door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. a) Toughened glass 12mm thick

Acoustical door : Providing & Fixing in position Acoustical Doors along with150x150mm teakwood frame, doors made from 50mm Teakwood frame 600x600 ctoc filled with 1000Gsm synthetic wool 50mm thick and 3mm Tec sound from both sides, 12mm water proof ply & veneer from both sides, including 150 mm heavy duty SS hinges (Geze/Dormaoreq.) 4 no ,withDoor-closer (Dorma/Gezeoreq.) including cost of required Cut-Outs, decorative mouldings/finishing-items/melamine polish & Scaffolding asper Architectural & Acoustical Design & Instructions & Complete in all aspects. including all materials labour, finishing etc complete.

SUBHEAD IX : ROOFING AND WATERPROOFING

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of : i) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg. per sqm of area. iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.) Plan area shall be measured for payment Service gurantee shall be given as per General condition of contracts from the date of completion,. Any defects noticed during service gurantee period shall be rectified immediately at the risk and the cost of contractor .

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats (bats of 2nd class bricks) with mortar using broken well burnt brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120mm and minimum thickness at khurra as 65 mm. Service gurantee shall be given as per General condition of contracts from the date of completion,. Any defects noticed during service gurantee period shall be rectified immediately at the risk and the cost of contractor .

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. i) For vertical surface two coats @ 0.70 kg per sqm

ii) For horizontal surface one coat @1.10 kg per sqm.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm + 0.05 %, total coated thickness with zinc coating 120 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval,

including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm or both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I.12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I

Providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) for construction joints treatment of RCC structure such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. After cleaning the surface, one coat of required primer forswellable water stop tape shall be applied throughout the length of the joint @3.78 litre per 240 running meter. Over the primed surface swellable type water stop tape shall be placed. The work shall be carried out all complete as per specification and the direction of the Engineer-In-Charge. The product performance shall carry guarantee for 10 years against any leakage.

SUBHEAD X : STRUCTURAL STEEL WORK

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. (The bottom row should be 14 cm above ground and the rest at spacing of 2.5 cm centre to centre.) With G.I. barbed wire

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm

Supply and Fixing in position Motorised Sliding Gates as per Specifications and drawing with all required Fixtures and Accessories Fabricated to best workmanship with one Coat of Epoxy Grey Primer and 2 coates of Epoxy paint etc complete as directed by engineer in charge. Size of Gate - 7.00 m(Minimum) X 3.00 m Clear Opening - 6.00m Details are as follows. Outer frame : will be fabricated out of 100 mm x 100 mm x 4 mm M.S box section of approved make. Vertical members:50 x 50 x 2 M.S box section of approved make. Front Side Bottom: 1.6 mm M.S sheet will be provided on the front side of the gate as per the design.(400mm Height). 25 x 25 x 2 mm Box section vertical and Horizontal members will be provided for M.S sheet support. Galvanized bottom Rollers :- Precisely made nickel plated Heavy Duity Bottom wheel (Suitable for Outdoor function) as per the gate to be provided with double Z-bearings and Oil seals assembled in a steel fabricated bracket, which will make them dust proof for providing long life.

Nylon roller with bearing to be provided with steel Fabricated brackets to Guide the sliding Gate. Bottom Rail:-Bottom Rail duly fabricated on 125mm x 75mm M.S I-beam to be provided with gate along with 25 mm bright bar on the top. Length of rail : Minimum 13 m / as per manufacturer requirement for 6m wide Gate. Automation:- Make :- FAAC(single Phase)/ equivalent Model:- Faac 844 ERZ16 (single Phase) / equivalent Anti-crushing protection is ensured by an electronic device directly controlling drive torque. Gear motor is non-reversing In the event of a power cuts the rotation of the (key protected) release device makes it possible to open and close the gate manually. Simplified "on display" programming. Integrated encoder for reverse function on obstacle and accurate management of partial opening and slow down. Including limit switch Model:- 844 ERZ16 Power supply :- 220 – 240V Power Consumption : 660W Max Gate Weight : 1800kg Max Speed : 9.5 m/min Protection:- IP44 Push Button to be provided & Included in this.

Photocells :- Photocells to be provided to reverse the motion of gate when it detects the motion of vehicle during closing of gate which will provide extra safety to avoid accidents. Remote Receiver and Remotes :– One receiver – Plug in Receiver Remotes - 2 Nos. (1-channel remotes) I- rack: - Galvanized Rack 30mm x 12mm I-rack 7 meter along the length of the gate. Wieldable spacers included: - 21 Num to be provided. With fasteners.

Supply and Fixing in position Manual wicket Gates as per Specifications and drawing with all required Fixtures and Accessories Fabricated to best workmanship with locking arrangement , one Coat of Epoxy Grey Primer and 2 coates of Epoxy paint etc complete as directed by engineer in charge. Size of Gate - 1.50 m(Clear Opening) X 3.00 m Details are as follows. Outer frame : will be fabricated out of 100 mm x 100 mm x 4 mm M.S box section of approved make. Vertical members:50 x 50 x 2 M.S box section of approved make. Front Side Bottom: 1.6 mm M.S sheet will be provided on the front side of the gate as per the design.(400mm Height). 25 x 25 x 2 mm Box section vertical and Horizontal members will be provided for M.S sheet support. This gate will be manual and can be opened in both thedirection. Wicket gate will be operatedby pivot system.

SUBHEAD XI : SIGNAGES

Supply and fixing of 18 gauge Stainless Steel plates of grade 304 engraved with approved matter writing all complete as per sample approved and fixed with two rawls plugs stainless steel srew required nos of holes, as per direction of Engineer-in-Charge.

Supply and fixing of Indicative sign boards size of required size made out of 3 mm thk acrylic sheet/ Sun boars/ ACP sheet Green/ Red Colour Glow Night Tape pasted on sheet with single side writing with fixing on wall,fixed with four rawls plugs stainless steel srew/ double side tape of 3M make required nos of holes, wherever required complete as per direction of Engineer-in-Charge.

Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all completeas per drawings, specification and direction of the engineer-incharge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bilingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of Engineer--in-charge.

a) Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm

b) Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm

SUBHEAD XII : ROAD & HARD STANDING

Construction of granular sub-base by providing close graded Material conforming to specifications,mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanical broom. With medium setting bitumen emulsion On W.B.M / W.M.M. @ 0.4kg/sqm

Providing and laying Dense Graded Bituminous Macadam using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of Engineer-in-Charge. 50 to 100 mm average compacted thickness with bitumencof grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin- Charge. 60mm thick Cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material,labour,T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. New work (Two or more coats)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

a) 150mm dia

b) 300mm dia

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete

a) 450mm dia

b) 600 mm dia

c) 900 mm dia

d) 1000 mm dia (Laying by mannual/ machenical means)

SUB HEAD XIII : SANITARY SERVICES

Providing and fixing white vitreous china wall mounting water closet of approved size & shape including providing & fixing Low level flushing cistern with dual flush plates and fittings, including seat cover,nuts, bolts and gasket etc complete. Including all the items metioned as below. Item Details:- a) WC PAN Wall Mounted with seat Cover :- Parryware Cat . No. : Priomo CO23H or equivalent. b) Flush Tank - Make - Parryware Cat . No. : Slimline Premium E8392 or equivalent. c) CP Angle stop cock:- Jaquar Model no.CON 059 KN or equivalent. d)PVC Connection Pipe : Parryware Cat . No. : T991999 PVC Hose 2 ft. or equivalent. e) Flushing Pipe : Parryware Cat . No. : Long Bend Pipe E 8334 or equivalent

Providing and fixing white vitreous china extended wall mounting water closet of approved size & shape including providing & fixing concealed cistern with dual flush plates and cfittings, nuts, including seat cover, , bolts and gasket etc complete.Including all the items metioned as below. Item Details:- a) WC PAN:- Hindware Wall Mounted Dove 20080 or equivalent b) Flush Tank with flush pipe :- Make - Hindware Model No. CONCEALO NEO ( 80MM) Cat . No. 517444 or equivalent. c)Flushing Plate : Make - Hindware Model No. Loop Neo Chrome Flush plate . d) CP Angle stop cock:- Jaquar Model no.FLR 5053N or equivalent

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required etc complete including all the items metioned as below. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests Item Details:- a) WC PAN:- Hindware WC 20042 or equivalent b) Flush Tank with flush pipe :- Hindware Sleek Essence Dual Flush(511217) or equivalent. c) CP Angle stop cock:- Jaquar Model no.CON 059 KN or equivalent. d)PVC Connection Pipe : Parryware Cat . No. : T991999 PVC Hose 2 ft. or equivalent

Providing and fixing white vitreous china battery based infrared sensor operated urinal(Wall Hung) of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Including items metioned as below. Item Details:- a) Urinal PAN:- Hindware Flow, Model No- 60021 or equivalent b) CP bottle trap :- Inbulit c) Waste coupling :- Inbulit

Providing and fixing white vitreous china flat back half stall urinal of size 590 X 390 X 375 mm with urinal valve with autoclosing system with builtin control cock & wall flange) and Bottle trap, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Including items metioned as below. Item Details:- a) Urinal PAN:- Hindware FLAT BACK L ARGE Cat . No. : 60002 or equivalent. b) Urinal valve with autoclosing system with builtin control cock & wall flange) :- (Jaquar make,Model No-PRS077) or equivalent. c) CP bottle trap :- (Jaquar make,Model No-ALD 769) or equivalent. d) Waste coupling :-Waste Coupling ALD 709 or equivalent

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass auto closing pillar taps, 32 mm C.P. brass waste of standard pattern, CP Bottle trap, including painting of fittings and brackets, cutting and making good the walls wherever require etc complete as per manufacturers specification and direction of Engineer-in-charge. Including items metioned as below. Item Details:- Basin a) Wash Basin:- Hindware Wall Hung Neo Cat . No. : 10103 or equivalent b) CP bottle trap :- Jaquar Model,Model No- ALD 769 or equivalent c) Waste coupling :- Jaquar Model no ALD 705 or equivalent d) Pillar Cock :- Jaquar Model PRS-031 or equivalent e) Connection Pipe :- Jaquar Model ALD 803B or equivalent

Providing and fixing over the counter wash basin with 15 mm C.P. brass auto closing pillar taps, 32 mm C.P. brass waste of standard pattern, CP Bottle trap, including painting of fittings and brackets, cutting and making good the walls wherever require etc complete as per manufacturers specification and direction of Engineer-in-charge. Including items metioned as below. Item Details:- a) Wash Basin:- Hindware PAERL Cat . No. : 91088 or equivalent b) CP bottle trap :- Jaquar Model,Model No- ALD 769 or equivalent c) Waste coupling :- Jaquar Model no ALD 705 or equivalent d) Pillar Cock :- Jaquar Model PRS-031L65 or equivalent e) Connection Pipe :- Jaquar Model ALD 803B or equivalent

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, CP Bottle trap, including painting of fittings and brackets, cutting and making good the walls wherever require etc complete as per manufacturers specification and direction of Engineer-in-charge. Including items metioned as below. Item Details:- Basin a) Wash Basin:- Hindware Wall Hung Neo Cat . No. : 10103 or equivalent. b) CP bottle trap :- Jaquar Model,Model No- ALD 769 or equivalent. c) Waste coupling :- Jaquar Model no ALD 705 or equivalent d) Pillar Cock :- Jaquar Modeln CON-011KN or equivalent e) Connection Pipe :- Jaquar Model ALD 803B or equivalent

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required etc complete

Kitchen sink without drain board 610x510 mm bowl depth 200 mm Including all the items metioned as below. Item Details:- Nirali Make :- Model Grace Plain Super Glossy or equivalent CP bottle trap :- (Jaquar make,Model No-ALD 769) or equivalent Sink Cock :- (Jaquar make,Model CON-357KN) or equivalent CP Angle stop cock:- (Jaquar Model CON 059KN) or equivalent Waste coupling :- (Jaquar Model no ALD 705) or equivalent

Kitchen sink with drain board 915 x 510 mm bowl depth 200 mm Including all the items metioned as below. Item Details:- Nirali Make :- Model Elegance Delux BG_ BIG or equivalent CP bottle trap :- (Jaquar make,Model No-ALD 769) or equivalent Sink Cock :- (Jaquar make,Model CON-357KN) or equivalent CP Angle stop cock:- (Jaquar Model CON 059KN) or equivalent Waste coupling :- (Jaquar Model no ALD 705) or equivalent

Providing and fixing Wall Mixer with Provision For Overhead Shower with 115mm Long Bend Pipe On Upper Side, Connecting Legs & Wall Flanges for bath and shower etc complete including all the items metioned as below. Item Details:- Make :- Jaquar CON-273KNUPR or equivalent

Providing and Fixing Over head shower 105 mm dia with Shower Arm etc complete including all the items metioned as below. Item Details:- Make :- Jaquar OHS-1989, Jaquar SHA-477 or equivalent

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing C.P. Brass toilet paper holder. Item Details:- Make :- Jaquar AQN-7753 or equivalent

Supplying & Fixing of CP liquid soap container of pump type with initial soap fill all hardwares etc complete. Item Details:- Make :- Jaquar ACN- 1135N or equivalent

Supplying & Fixing of CP Towel Ring with flange & all hardwares etc complete. Item Details:- Make :- Jaquar ACN-1121BN or equivalent

Supplying & Fixing of CP Towel rail 600mm long with flange & all hardwares etc complete. Item Details:- Make :- Jaquar ACN-1111SM All Showers

Supplying & Fixing of SS Towel rack 600mm long with lower hanger & all hardwares etc complete. Item Details:- Make :- Jaquar ACN-1181S All Showers

Providing and fixing CP health faucet for ablution at toilets in heavy quality with 1000mm Long Braided Hose, wall hook and CP two way Bib cock etc complete as directed by Engineer In Charge. Item Details:- Make :- CP health faucet: Jaguar ALD 577 or equivalent CP 2 Way Bib Cock :- Jaquar Model FLR 5041N or equivalent

Providing and fixing 15 mm nominal bore C.P. brass short body bib cock of approved quality conforming to IS : 8931. Item Details:- Make :- Jaquar CON-041KN or equivalent

Providing and fixing approved type SS coat hooks with concealed type screws of approved make. Item Details:- Make :- Jaquar ACN-1161N or equivalent

Supplying & Fixing C P Angle Stop Cock of approved make complete as directed. Provisional Item Details:- Make :- Jaquar Model no.CON 059KN or equivalent

Providing and laying P.V.C. rigid waste pipe for sink or wash basin including P.V.C. waste fittings complete.

32 mm dia

50 mm dia

Supplying & laying PVC Pipes conforming to I.S - 13592 type B including necessary fittings and joining with rubber rings and lubricants as per standard practice with holder bats; PVC clamps, bends, tees, clean outs, vent cowls, dash fasteners fixed to walls,beams, or ceiling as required slope, pcc bedding and necessary special heavy detachable MS bracket and Testing as per standard Practice and as directed by Engineer In Charge. Soil, Waste & Vent Pipes

110 mm dia pipe.

75 mm dia pipe.

Providing and laying on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. Rain Water Pipes

75 mm diameter

110 mm diameter

Providing and fixing PVC P / Multi Trap with Square SS jali with Frame

110 X 110 mm dia Size P Trap with 100mm Jali

75 X 75 mm dia Size Multi / Nahani Trap with 100mm Jali (Ground floor Qty to be shifted in b)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing, Supplying & Drilling/ Core cutting of required dia outlets using low vibretion mechanical means. Cost to include identifiction of embeded reinforcement using profometer, closing of core cut using self sealing nonshrink groute of approved make either single or double component with necessary form work, staging, tools, etc complete as directed by Engineer In Charge

100mm dia

150mm dia

Providing and fixing differently abled toilets including fixing accessories and accessories Set,etc complete. Including all the items metioned as below. a) Water closet:Wall Hung WC with UF soft close seat cover, Hinges and Accessories Set, Size : 350x750x340 mm Jaquar Cat No. DIS-WHT-93951UF or equivalent. b) Wash Basin :Wall Hung Basin With Fixing Accessories, Size: 650X565X155 mm - 1 No. Jaquar Cat No. DIS-WHT-93801 or equivalent. c) Grab Bar Vertical Swing: 1 No. Jaquar Cat No. WAC-WHT-BG0800 or equivalent. d) Grab Bar 692 mm Long: 2 Nos. Jaquar Cat No. WAC-WHT-BR0600 or equivalent. e) Flush Tank with pipe - Wall Hung Cistern with 39mm Drainage L-Bend Pipe with Gasket & Installation Kit (Suitable for EWC) Jaquar Cat No. JAH-WHT-184NL or equivalent. f) CP Angle stop cock:- Jaquar Model no.CON 059 KN g) CP bottle trap :- Jaquar Model,Model No- ALD 769 or equivalent h) Waste coupling :- Jaquar Model no ALD 705 or equivalent. i) Pillar Cock :- Jaquar Model CON-011KN or equivalent j) Connection Pipe :- Jaquar Model ALD 803B or equivalent

SUB HEAD XIV: WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes SDR 11/ SCH40, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints completeas per direction of Engineer in Charge. Internal work - Exposed on wall

15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clampsat 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm dia nominal outer dia pipe

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

Providing and fixing Bronze gate valve with C.I. wheel of approved quality (screwed end) :

32 mm nominal bore

40 mm nominal bore

Providing and fixing Ball valve (bronze) of approved quality, High or low pressure complete as directed.

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

SUB HEAD XV: EXTERNAL SEWAGE DISPOSAL

Supplying & fixing uPVC Pipes conforming to I.S - 15328 & providing Nominal ring stiffness of SN 4 kn/m sq including necessary fittings and joining with rubber rings and solvents as per standard practice laid to required alignment and slopes in excavated trenches.

110 mm diameter (SN 8)

160 mm diameter (SN 4)

200 mm diameter (SN 4)

250 mm diameter (SN 4)

315 mm diameter (SN 4)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing / refilling of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Supply and Fixing of pipeline route marker with suitable size angle at a height of 500mm above ground including excavation of pit making the PCC block for grouting, backfilling painting with approved shade, for water supply pipeline complete with suitable gasket, Bolts & Nuts and other fixing accessories etc., complete

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design:

110 mm diameter

160 mm diameter

200 mm diameter

250 mm diameter

315 mm diameter

Providing and fixing square-mouth uPVC gully trap with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design with FPS bricks. 110 mm size

Constructing brick masonary chamber ,With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

a) Inside size 90x45 cm and avg 75 cm deep including DI cover with frame -MD load bearing capacity

b) Inside size 60 x45 cm and avg 75 cm deep including DI cover with frame - MD load bearing capacity

Extra for depth for manholes With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 . a) Size 90 x 45 cm

Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with DI Cover and frame HD load bearing capacity, 560 mm internal diameter fixed in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

2.3 m deep with DI Cover and frame HD load bearing capacity, 560 mm internal diameter fixed in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond 2.30 m : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supply, Installation & Commissioning of Sewage Treatment Plant of Capacity 50 CUM / DAY System- MBBR ( Mix Bed Bio Reactor ) Untreated Sewage Characteristics. PH 7.5-8.5 Total Suspended Solids - 180-220 mg/lit. BOD3 (270c ) 200-350 mg/lit. COD 400-500 mg/lit. Oil& Grease 20 mg/lit. Treated Sewage Characteristics. PH 6.5 - 8.5 Total Suspended Solids - Less than 5 mg/lit. BOD3 (270c ) Less than 10 mg/lit COD Less than 30 mg/lit. Oil& Grease Less than 5 mg/lit. Scope Includes :- Design Engineering MCC panel with necessary cableing. Necessary consumables Interconnecting piping, valves & fittings. Necessary Equipment Foundation Treated Water testing report Unloading/ shifting/ storage of supplied material. Refer Technical Specification for Details

Supply, lowering & installation of RCC readymade humepipe septic tank at suitable location including earth work excvation in all types of soil, necessary pcc bedding as directed including sewerline connections at inlet & outlet, Inspection Chambers etc., complete as per standard design & as directed. 25 User Capacity

Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W.drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

The installation shall be complete with all necessary indigenous accessories as required to complete. (Cost to include suitable gun metal isolation valve,strainer on its suction line and gunmetal check valve and gunmetal isolation valve on its delivery line for each pump with end blind flanges as per approved shop drawings/documents and as per satisfaction of engineer in charge). Vendor to submit proposed pump model with duty curve Capacity : 100-300 lpm Head : 8-16 m Max Solid Size : 20mm Pumps : 1 W + 1 S (1 Set)

SUB HEAD XVI: ELEVATOR

Supplying, installing, testing and commissioning of 12 Passenger Lift for Ground + 4 Level with 884 Kg GEARLESS LIFT MR/MRL, COPO/ TOPO doors with frame having opening of 900/1000 mm wide X 2000 mm high with Automatic Rescue Device, Audio- Visual, Overload indicator, Infra red curtain, 3VF drive, Emergency alarm, Fire alarm switch, overload warning indicator, suitable door safety as specified, suitable for physically challenged persons, complete in all respect as specified in technical specifications. The lift shall be provided with 3 year free defect liability period shall conforms to IS 14665

Supplying, installing, testing and commissioning of 10 Passenger Lift for Ground + 6 Level with 680 Kg GEARLESS LIFT MR/MRL, COPO/ TOPO doors with frame having opening of 800 mm wide X 2000 mm high with Automatic Rescue Device, Audio- Visual, Overload indicator, Infra red curtain, 3VF drive, Emergency alarm, Fire alarm switch, overload warning indicator, suitable door safety as specified, suitable for physically challenged persons, complete in all respect as specified in technical specifications. The lift shall be provided with 3 year free defect liability period shall conforms to IS 14665

Supplying, installing, testing and commissioning of 8 Passenger Lift for Ground + 5 Level with 540 Kg GEARLESS LIFT MR/MRL, COPO/ TOPO doors with frame having opening of 800 mm wide X 2000 mm high with Automatic Rescue Device, Audio- Visual, Overload indicator, Infra red curtain, 3VF drive, Emergency alarm, Fire alarm switch, overload warning indicator, suitable door safety as specified, suitable for physically challenged persons, complete in all respect as specified in technical specifications. The lift shall be provided with 3 year free defect liability period shall conforms to IS 14665

Supplying, installing, testing and commissioning of 8 Passenger Lift for Ground + 2 Level with 540 Kg GEARLESS LIFT MR/MRL, COPO/ TOPO doors with frame having opening of 800 mm wide X 2000 mm high with Automatic Rescue Device, Audio- Visual, Overload indicator, Infra red curtain, 3VF drive, Emergency alarm, Fire alarm switch, overload warning indicator, suitable door safety as specified, suitable for physically challenged persons, complete in all respect as specified in technical specifications. The lift shall be provided with 3 year free defect liability period shall conforms to IS 14665

SUB HEAD XVII: FILTRATION SYSTEM

Conventional Type Filtration

Plumbing , Piping and valves

Supply of inter connecting piping & fitting for swimming pool suction and delivery of Treated water to pool & suction and discharge.

Supply of UPVC/Rigid grey PVC ISI marked Sch.80/40, Required quantity of check valves, Control Valves , Pipe firrings and consumables.

Filtration System - Conventional

Supply of emaux make filter feed pumps of 120000 litrs/ hour flow with inbuilt strainer basket, SS 316 shaft & mechanical seal, self priming type, with removabl;e basket lid. ( 1 Working + 1 stadndby ) Model EPH-400-( 3 Working 1 standby)

Emaux Australia make : Bobbin Wound Fibre glass reinforced vessel with ABS laterels inside and multiport valve of 2' Size , with average hourly flow rate of 52000 lit/hr, Model V - 1200/S-1200

Filter media for the above filter - Graded Quartz Silica Sand , Indian origin

POOL FITTINGS

Supply of Floor inlet Nozzles for distribution of the trated water into pool , at the pool Bottom , to be fitted in the piping embeded in the concrete, OR if Brick Bat Coba is there the piping will be done Before Brick Bat Coba is done

Supply of imported white colour covers (in the pool ) for fitter suction point-2, vaccum point-2, gutter drain out lets , etc

Supply of overflow gutter grating moulded out of virgin quality PPCP granuals, 35mm thick and 450 mm width

Supply of swimming pool overflow type ladders, of SS 304 - 5 Steps on deep side 3600mm depth Model of series.

Supply of swimming Pool overflow Type Ladders, of SS 304 - 5 Steps on 1350 mm Depth - 2 Nos in the middle and 2 nos at end (Model of series)

POOL MAINTENANCE EQUIPMENTS

Supply of Emaux Australia Make Pool Cleaning equipment - consisting of following 8 items : i) Leaf Skimmer, PVC CE 101 ii) PVC curved Brush, 18" CE 201 iii) SS Algaei Brush 18" iv)15 meter of light weight flexible premium house pipe CE 157. v) Extendable telescopic aluminium Pole , 2X2.4M - CE132. vi)Aluminium Suction Head - 18". vii) Test kit CE 029. viii) Deep Net in PVC - CE201

SUCTION SWEEPER EQUIPMENT : Trolley mounted suction sweeper PUMP with 50 meters of cable (2.5 sqmm X 3 Core copper) and local push button station for on-off and with hooks for attaching vaccum suction hose & cable etc.

Sanitisation chemicals / disinfection/coagulation chemicals for stat up Grannual Chlorine for intial start up & commissioning

Alum Powder for initial start up & commissioning

POOL ILLUMINATION & ELECTRICALS

Supply of "CES' indian make underwater lights: made out of imported LED bulb,encased in water proof IP 68 protection aluminium housing , with front cover in SS 316, to be mounted on side wall of Pool , of 12 vo;ts/18 watts complete with LED Drive , mounted on control panel

Electrical cabling for panel room & underwater light From pool to Control Panel, complete with conduits, sadle/Tray where ever required etc. 2.5mm Sq. X 2 cor , for main Pool and 1.5 Sqmm X 2 core for step lights, copper,Poly cab make ISI marked (With conduting) All lights will have individual cabling and common control Panel.

Electrical control panel for all equipment for swimming pool including U W lights, Filter Pump , ozoniser, UV sterilizer , Heat Pump, cabling and wiring for the equipment wuth in the Plant room buyers has to provide single point electric connection, with proper termination and isolation arrangements, as per mandate.

OZONIZER 100 GPH air cooled ozonation system Scope : CECON 100 GPH air cooled ozonator , 20 LPM oxygen concentrator, venturi injector 1", Booster Pump and ORP controller (Ozone wall reduce the usage of Chlorine upto 70-75%)

SUB HEAD XVIII: AIR CONDITIONING

Supply installation testing and commissioning of VRF system comprising of outdoor units with air cooled condenser, Inverter scroll / rotary compressor, assembled and wired in a single modular package.The outdoor unit shall be factory assembled, weather proof casing, constructed from heavy gauge mild steel panels and coated with baked enamel finish. The outdoor unit should be fitted with low noise aero spiral design fan. The unit should be completely factory wired, tested with all necessary controls, outdoor unit structural stand Unit shall be modular and Each modular outdoor shall be with Inverter rotary compressor/ Scroll compressor. The refrigerant shall be R-410a. First charge of refrigerant to be included The heat exchanger shall be constructed with copper tubes mechanically bonded to aluminum fins to form a cross fin coil. The aluminium fins shall be covered with anti corrosion resistant film. The unit shall be provided with its own microprocessor control panel with all safety controls, starting controls, operating controls with full feature micro computer based controller with real time clock and programming / diagnosis facilitty. All units to be supplied with necessary isolator and ELCB

Supply installation testing and commissioning of indoor units with following details Cassette type unit casing shall be galvanised steel plate supplied with suitable decorative panel, 4 way gille with plug and wire 1.5 m long. Unit must be insulated with sound absorbing thermal insulation material, Polyurethane foam. The noise level of unit at the highest operating level shall not exceed 42 dB(A), at a vertical distance of 1.5 m from the grille of the unit. The unit shall be supplied with Resin Net filter with Mold Resistance. The filter shall be easy to remove, clean & re install. Unit shall have provision of connecting fresh air without any special chamber. The unit must have in built drain pump, suitable for vertical lift of 750 mm. Cordless controller - Remote cordless controller

1.3 TR Compact cassette

2.6 TR Ducted UNIT

5.0 TR Ducted UNIT

1.00 TR HI-WALL MOUNT

1.30 TR HI-WALL MOUNT

1.60 TR HI-WALL MOUNT

2.00 TR HI-WALL MOUNT

Intelligent Central Remote Controller for complete monitoring and oepration of VRV system with connectivity provision to BMS

Supply and installation of Refrigerant piping joints for VRF system both suction and liquid line

Supplying, installing, testing and commissioning of factory built floor mounted mentioned, DX Coil double skin type air handing units made of 50 mm thick panels consisting of G.I.casing of thickness 0.63 mm outside layer and 0.8 mm inside layer with polyurethene foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower section with plug fan suitable for static pressure as detailed below, DX cooling coil section with aluminium finned copper tubes (tube thickness not less than 0.5mm) cooling, filter sections with 50 mm thick metal viscous/washable synthetic type air pre-filters - Class EU-4 Direct drive package with TEFC drive motor suitable for 415 + 10% volts, 50 HZ, 3 phase, IE 2 energy efficiency stadards, motor suitable for VFD , A.C. supply, drain connections, stainless steel drain pan necessary vibration isolation arrangement etc. complete as per specifications and of following capacities

8000 cfm / 20 TR Dx coil / 6 ROWS/ 65 MM SP

Supply and installation of AHU Communication Kit PCB based with 220 V supply operation

Supply and installation of AHU Connectivity kit to VRF Outdoor units with suitable Electronic Expansion valves

FRESH AIR HANDLING UNITS

Supplying, installing, testing and commissioning ofCabinet inline fan, fan section to house supply fan with motor, mixing box complete as per specifications and of following capacities. Capacities as Below

1800 CFM / 25 MM TSP Fresh air fan

1600 CFM / 25 MM TSP Fresh air fan

900 CFM / 25 MM TSP Fresh air fan

10000 CFM / 65 MM TSP liftwell preesurization fan

Supplying, Installing, testing & commissioning of Air cooled ducted split unit machine with each having a capacity and details as mentioned below comprising of the following complete as per specifications and as reqd. Refrigerant shall be R-410a / 407C 8.5 TR / 4250 CFM Ducted split unit- Standard unit Scroll type compressor hematic complete with automatic capacity, safety switches, lubrication system, etc. as per specifications. Suitable capacity squirrel cage induction motor with class 'B' insulation suitable for operation on 415 + 10% volts, 50 Hz, A.C. supply for Blower motor. Necessary starters suitable for compressor motor complete with over load protection, under voltage protection, protection against phase reversal & independent single phase preventors etc complete as required. Necessary drive arrangement for blower motor . Matching Air cooled condenser with necessary fittings for refrigerant piping connections, necessary structural support for mounting condensers Microprocessor based control panel complete with accessories, machine isolation / disconnect switch as per specifications. Auto change over of units to be provided to manage equal run hours of working and standby unit. Suction line insulation with minimum 19 mm thick nitrile rubber insulation. Exposed piping to have UV protection and mechanical protection Initial / first charge of refrigerant gas & compressor oil

Supply of rectangular sound attenuator. 20 gauge GI casing construction & internal splitters with 22G galvanized sheet. Splitters with sound absorbing material has a glass fill tissue, facing galvanized shaped perforated sheet. Splitter have conical end at the air flow direction to minimise air pressure and regenerated noise. Internal splitters shall be 22 gauge minimum galvanized perforated steel and filled with inorganic acoustic absorbent material of sufficient density and packed under at least 5% compression to eliminate voids due to vibration and setting. Sound attenuation to be min 10 dBA and pressure drop not to exceed 15 mm wc. 8000 Cfm air qty - 1300 x 600

Supply installation testing and commissioning of Refrigerant Piping fabricated out of hard drawn copper of 18 G conforming to ASTM B75 / ASTM 280 BS 2871 suitable for R-410a Refrigerant. Copper pipes shall be De oxidised. Pressure testing, flushing of piping, Suction Gas line to be insulated with 19 mm nitrile rubber / crosslinked polyethylene insulation backed with factory backed aluminium ribbed foil of following sizes- Bidder shall check and confirm as per their outdoor unit configuration. Necessary supporting arrangements for piping as per tender drawing shall be included. Piping exposed to atmosphere on terrace shall be with factory backed glass cloth.

Supply installation testing and commissioning of Refrigerant Piping fabricated out of hard drawn copper of 18 G conforming to ASTM B75 / ASTM 280 BS 2871 suitable for R-410a Refrigerant. Copper pipes shall be De oxidised. Pressure testing, flushing of piping, Liquid line to be insulated with 13 mm nitrile rubber / crosslinked polyethylene insulation backed with factory backed aluminium ribbed foil of following sizes- Bidder shall check and confirm as per their outdoor unit configuration. Necessary supporting arrangements for piping as per tender drawing shall be included. Piping exposed to atmosphere on terrace shall be with factory backed glass cloth

Supply and laying of UPVC pipe conforming to IS 4985 : 2000 6 KG/sqcm. Drain pipe shall be with 6 mm cross linked polyethylene insulation / nitrile rubber insulation.

Supply, installation, testing of galvanised sheet metal ducting as per CLASS VII as specified complete with Galvanised companion flanges girth angles, Turning vanes, structural support systems, necessary gripple wire supports above crane Closed cell neoprene gasket. Construction standards as per IS 655. Ducting shall be factory fabricated

0.63mm (24 G) galvanised sheet steel

0.8mm (22 G) galvanised sheet steel

Flexible Duct 100mm dia

Supply and installation of Aluminium Powder coated louvers with bird screen, mosquito screen and filter - 10 micron

Supply and fixing of opposed blade GI Manual Volume control dampers of 18 G casing for ducts as specified.

Supplying, fixing, testing and commissioning of GI fire dampers in supply air duct/main branch and return air path as & where required of required sizes including control wiring. The damper shall be fusible link type with 90 min fire rating. Damper sleeves of MS 18 G shall be provided to grout in the wall.

Supply and installation of aluminium powder coated grilles with collar damper

Supply and installation of aluminium powder coated Supply/Return diffusers with VCD

Supply and fixing of 19 mm thk cross linked polyethylene of density. Thermal conductivity shall not exceed 0.035 W / m deg K. Insulation material shall be with factory backed aluminium ribbed aluminium foil duct insulation for supply and return air duct as per specifications.

Supply and installation of acoustic insulation with 10 mm thick open cell crosslinked polyethylene insulation

ELECTRICAL WORKS

Supply,erection & commisioning of following floor mounted cubicle panel boards fabricated from 2mm thick CRCA sheet painting provided by seven tank cleaning process & powder coating process.The panel shall be provided with 50 x 6 mm GI earth flat.The following Breakers shall be provided with DMC/SMC busbar insulators,aluminium bus bars of suitable ampere range with heat shrinkable colour coaded sleeves,interconnections through proper copper lugs shall be provided.The panel shall be manufactured by CPRI approved manufacturers.

MV Cables Supply, laying and commissioning of following size 1.1KVgrade XLPE PVC insulated armoured copper conductor cable with glands and terminations, lugs on cable tray with all installation materials.

4C x 10 Sq.mm. ( XLPE Copper Armoured )

4C x 6 Sq.mm. ( XLPE Copper Armoured )

3C x 4 Sq.mm. ( XLPE Copper Armoured )

2C X 1 sqmm copper unarmoured stranded communication cable in PVC conduit for VRF

EARTHING Providing & fixing in position the following PVC Insulated Green Outersheath copper wire including providing all fixing accessories & effecting proper connections bu using tin plated copper lugs.

4 sqmm copper wire

GI srips - 50 x 5 mm thick ( For panel )

CABLE TRAYS Supply and fixing perforated type hot dipped galvanized cable tray with joints, connectors, suspenders, supports, GI Nut bolts of following sizes as per specifications. Galvanizing shall not be less than 50 micron.

300 mm wide x 62.5 mm x 2.0 mm thk

150 mm wide x 50 mm x 1.6 mm thk

STAND ALONE HI WALL SPLIT UNITS Supply installation testing and commissioning of Standalone Hi wall split unit of 3 star energy rating with suitable Voltage stabiliser complete with outdoor unit, MS epoxy painted stand for condensing unit, unit complete with pressure testing, gas charging. Refrigerant shall be environment friendly refrigerant. Ref piping - 10 mtr is included, control cabling, drain piping with insulation

2 TR- Hi wall

1.5 TR- Hi wall

SUB HEAD XIX:EXTERNAL WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling &testing of joints complete as per direction of Engineer in Charge.

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

50 mm nominal inner dia Pipes Flushing loop, STP to UGT

65 mm nominal inner dia Pipes- SCH 80 Domestic Loop

Providing and fixing Horizontal Centrifugal clear water pump set SS-304 casing, SS-304 impeller, SS-316 shaft, CI base with CED coating, complete directly coupled with TEFC induction motor of class "F" insulation & efficiency class EFF-1, 2900 RPM, suitable for operation on 415 volts ±10%, 3 phase, 50 Hz, A.C. supply ( with mechanical seal ), pressure gauges with gunmetal isolation cocks, necessary GI pipe reducer, vibration elimination pads, etc. mounted on a MS base frame bolted to cement concrete foundation complete in all respects and as per speicification complete as per directions of the engineer-in-charge with the following capacities: 1 Set - 1w+1s

Capacity : 300 lpm Head : 80 m Pump : 1 W + 1 S UGT to Individuals OH tanks for Domestic

Capacity : 200 lpm Head : 80 m Pump : 1 W + 1 S STP treated tank to Individuals OH tanks for Flushing

Providing and fixing 40mm GM ball float valve for tank filling complete as per specifications.

Supplying and fixing in position of approved make brass pressure reducing valve with necessary Ball valves of required dia for by pass arrangement etc. complete

Providing and fixing Ball valve (bronze) of approved quality, High or low pressure complete as directed. Make:- Zoloto, Leader, Sant & Audco

25 mm nominal bore

32 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

50 mm nominal bore

65 mm nominal bore

Providing and fixing CI Y type strainer of approved quality.

50 mm nominal bore

65 mm nominal bore

Providing and fixing Butterfly valve with SS Disc Nitrile Rubber Seal & O- Ring PN 1.6 pressure rating with hand lever operated including nut, bolt, flanges, gasket etc. complete as reqd.

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

80 mm nominal bore

Providing and Fixing Forged Brass Chrome Plated 25 mm Air release valve, having threaded connection including the cost of 25 mm dia Brass Ball valve with required fittings as per standard design.

Conducting Geological Survey in the respective area and submission of detailed report to assess the bore well locations including preparation and submission of report in triplicate, giving site plan showing test points and recommendations on location for bore well.

Drilling and developing of 150 mm dia Bore wells by DTH method in any type of soil, Conducting yield test as per V Notch method and submission of yield report, including filling of filter media clamps, MS Cover etc., blind C class pipe, MS slotted pipe & necessary fittings.

Supply & Installation of G.I Class `C' pipe with flanges at 6m intervals including excavation & refilling complete with all fittings, Valves, flanges, clamps as required. 80 mm dia Borewell Pump del to Ugt

Submersible Pump set suitable for 150 mm borehole with: Submersible Pump set Three phase electric motor with suitable HP Discharge: 400 LPM at 90m Head Control Panel with necessary cabaling Includes Necessary inlet outlet valves & Fittings, bends, tees etc Pump body: Cast Iron, Impeller: Bronze LTB2 , Shaft SS410. Before purchasing a pump Contractor should confirm pump capacity with bore well vendor

Supply, Installation & Commissioning of Water Treatment Plant of Capacity 50 KLD. System Consists :- Filter Feed Pumps 2 nos, Pressure sand filter, Activated Carbon Filter, Softner, UV Sterlizer, complete frontal piping, instruments & Valves, PLC cum MCC Panel with necessary etc. Nos of Streams-1 5 KLD / HR Scope Includes :- Design Engineering MCC panel with necessary cableing. Necessary consumables Interconnecting piping, valves & fittings. Necessary Equipment Foundation Treated Water testing report Unloading/ shifting/ storage of supplied material. WTP Package Refer Technical Specification for Details

SUB HEAD XX:FIRE FIGHTING

Supplying and fixing M.S 'C' Class pipes to IS: 1239/3589 flanged/welded as specified and with heavy clamps, hangers, brackets or pipe supports all with screwed/bolted joints with necessary specials ,fixing pipe supports into masonry walls or RCC anchor blocks and painting finishing coats of enamel paint of approved colour over a coat of approved primer after hydraulic testing to 14 Kg/Sq.cm pressure, complete as specified.

150 mm dia Pipe

100 mm dia Pipe

80 mm dia Pipe

Providing anti corrsoive Wrapping and coating with 4mm thick bitumasitc membrane (Pypcoat) for pipe laid below ground including all materials with minimum overlapping of 30mm

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed,within a lead of 50 m : All kinds of soil Pipes, cables etc. up to 300 mm dia

Supply and spreading of sand in layers not exceeding 100mm thick in excavated trenches as sand cushioning for the pipes all as specified and directed.

Supplying and fixing 150mm dia flanged C.I. tested non- return valve as per IS:5312 of approved make with necessary nuts,bolts,flanges, rubber gasket etc. complete as specified.

Supplying and fixing 100mm dia flanged C.I. tested non- return valve as per IS:5312 of approved make with necessary nuts,bolts,flanges, rubber gasket etc. complete as specified.

Supplying and fixing weather proof courtyard fire hydrant FRP hose cabinet with 2.2mm thickness of about 800 mm x 600 mm x 250 mm size capable of accommodating two lengths of 63 mm dia.canvas hose of 15 Mtr. length with locking arrangement, and lever for opening the door after breaking glass. With Stainless Steel Hinges Painted Fire Red Outside And Inside. Each hose box to be fitted with glass door in front. etc. complete as specified.

Fire Hydrant valve, Single Outlet, Gunmetal, 80mm N.B. flanged inlet, brass spindle, 63mm female inst oblique outlet, complete with C.I wheel, ABS blank cap & GI chain, bearing IS:5290 mark, flange O.D.200mm, PCD 160mm, four 19mm dia. holes. Painted Red complete as specified

Supplying and fixing non-percolating flexible firefighting two layered delivery hose, synthetic fiber circular woven jacketed, with EPDM synthetic rubber lined, 38 kgf/cm 2 burst pressure, 23 kgf/cm 2 proof pressure, 15 kgf/cm 2 working pressure, bearing IS:636-2018 type 1 (Uncoated), 63 mm x 30m(15m X 2) length duly S.S. wire bounded to fire hose coupling, Gunmetal , instantaneous type, pair of male and female parts, bearing IS:903 mark. Branch Pipe Branch pipe - short, Gunmetal, 63mm male inst. inlet, male threaded outlet, fitted with 20mm bore nozzle, bearing IS: 903 mark.

Supplying and fixing hand held fire extinguisher ABC dry chemical powder type Fire Extinguisher of Capacity 4kg Confirms to IS 15683, bearing ISI mark complete with brass forged squeeze grip type valve fitted with pressure gauge , pressurize with dry Nitrogen gas filled, with discharge nozzle with wall mounting bracket.

Supplying and fixing hand held fire extinguisher ABC dry chemical powder type Fire Extinguisher of Capacity 9kg Confirms to IS 15683, bearing ISI mark complete with brass forged squeeze grip type valve fitted with pressure gauge , pressurize with dry Nitrogen gas filled, with discharge nozzle with wall mounting bracket.

Supplying and fixing CO2 type Fire Extinguisher of capacity 4.5 kg (6.8Liter) confirms to IS 15683, bearing ISI mark, consisting of High Pressure seamless steel cylinder (IS 7285) fitted with wheel type valve, fully charged with CO2 gas (IS 15222) & mounting brackets having fire rating 21B.

Supplying and fixing ISI grade approved 9 Ltrs. capacity galvanised round bottomed fire buckets painted Red and lettered 'FIRE' each with a bracket to hang the bucket on a wall or pillar as directed.

Supplying safety equipments as mentioned below:-

Shovel

Fire gong/hand size

Fire man axe

Supplying and installing Horizontal multistage direct coupled centrifugal pump as per manufacturer's pump characteristics data, cast iron casing and internal parts, make approved by Tariff Advisory Committee for fire duty, capable of discharging 2850 lpm. against 90 metre head, against all losses, complete with motor (H.P of motor to be confirmed from the pump manufacturer to suit the pump characteristics ) of approved make motor winding with class F insulation suitable for starter as per Fire Brigade / Supply Co. regulations, base plate, foundation bolts, suitable cable entry gland box, pressure gauges etc. and wired for gauges etc. and wired for automatic start on drop of pressure in the External Hydrant system.

Supply, Installation, Testing & Commissioning double flanged vertical Air vessel fabricated from 10mm M.S. plate with dished ends from 10mm M.S. plate, outside with one coat of primer and two coats of synthetic enamel paint of approved shade, complete with approved quality and sufficient number of pressure switches, air release valve, tripod type stand, pressure gauge with ball valve, drain ball valve of 50mm dia with 2.0 meter long GI (Heavy Duty ) piping complete as required and all other required accessories to operate commonly main fire pump, and Jockey pump at drop of pressure, automatically required pressure setting; Recommended dia. : 300 mm Height of shell : 1200 mm Working pressure : 12 Kg/Sq.cm Test Pressure : 18 Kg/Sq.cm

Providing and fixing Pressure gauge (0-14 Kg/Cm2) with necessary ball / isolation valve and fittings such as tees, elbows and painting and supports etc. complete. 100mm dia

Providing and fixing Standard type Pressure switch (for operation at 0-15 Kg./sqcm) with required fittings and accessories complete

Supplying and installing Jockey Pump as per manufacturer's pump characteristics data, cast iron casing and bronze/phosphor bronze internal parts, make approved by Tariff Advisory Committee for fire duty, capable of discharging 180 lpm. against 90 metre head, against all losses, complete with TEFC motor (H.P of motor to be confirmed from the pump manufacturer to suit the pump characteristics ) of approved make motor winding with class F insulation suitable for starter as per Fire Brigade / Supply Co. regulations, base plate, necessary MS pipe reducer, vibration pads,foundation bolts, suitable cable entry gland box, pressure gauges etc. and wired for gauges etc. and wired for automatic start on drop of pressure in External Hydrant system. Make:- Kirloskar, Grundfos, KSB, CRI

Providing and fixing C.I. sluice valves complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :

150 mm diameter - Class II

80 mm diameter- Class II

Providing and Fixing GM 25 mm Air release valve, having threaded connection including the cost of 25 mm dia Brass Ball valve with required fittings as per standard design.

Providing and fixing Cast Iron Butterfly valve with SS Disc Nitrile Rubber Seal & O-Ring PN 16 pressure rating with hand lever operated including nut, bolt, flanges, gasket etc. complete as reqd.

150 mm nominal bore

100 mm nominal bore

80 mm nominal bore

50 mm nominal bore

Supplying and fixing swinging type wall mounted fire hose reel to IS 884 with fire hose of braided rubber to IS 444 suitably reinforced Dunlop/Fire Stone make 19 mm size and 30 Mtrs. length,with 10 mm tapering branch nozzle in Brass male and female coupling with cut off valve attachment including fixing with approved anchor fasteners and bolts complete as specified. Branch Pipe Branch pipe - short, Gunmetal, 63mm male inst. inlet, male threaded outlet, fitted with 20mm bore nozzle, bearing IS: 903 mark.

Supplying and fixing Fire Hydrant valve, Double Outlet, Gunmetal, IS:318-LTB2 grade, 100mm NB flanged inlet, brass spindle, 63mm female inst. outlet, PVC blank cap, chain - IS:5290 mark, flange O.D.220mm, PCD 180mm, eight 19mm dia. holes complete as specified.

Providing and fixing Ball valve (brass) of approved quality, High or low pressure complete as directed. 20 mm nominal bore

Supply, Installation, Testing and Commissioning of electric driven Booster Pump with required 415 volts , 3 phase 50 Hz, 2900rpm, suitable soft Starter of required rating and required electrical cable from motor to panel , panel to pressure switch for terrace fire pump for automatic operation and complete in all respect as required:

Supplying and fixing Fire Brigade breach inlet connection with four connecting points SG Iron Body, 4 Nos GM 63 mm Male Inst. Inlet With Non- Return Valve, Drain Valve,Provisions for 25mm drain valve connection, OD 280mm x PCD 240 mm x 8 holes of 22mm dia, along with Pvc Blank Cap & Chain, WP 7 Kg/Cm2, TP 21 Kg/Cm2, Painted Red. as specified.

Providing and fixing Inlet Breeching 2 Way, SG Iron Body, 2 Nos GM 63 mm Male Inst. Inlet With Non- Return Valve, Drain Valve, 220mm OD, 180mm PCD, eight holes of 19mm dia, Pvc Blank Cap & Chain, WP 7 Kg/Cm2, TP 21 Kg/Cm2, Painted Red

Supplying, installation, testing and commissioning of diesel engine driven fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 2850 lpm. against 120 metre head

SUB HEAD XXI : FIRE SPRINKLER SYSTEM

Supplying and fixing M.S 'C' Class pipes to IS: 1239/3589 flanged/welded as specified and with heavy clamps, hangers, brackets or pipe supports all with screwed/bolted joints with necessary specials ,fixing pipe supports into masonry walls or RCC anchor blocks and painting finishing coats of enamel paint of approved colour over a coat of approved primer after hydraulic testing to 14 Kg/Sq.cm pressure, complete as specified. Above ground Piping

150 mm dia Pipe

100 mm dia Pipe

80 mm dia Pipe

65 mm dia Pipe

50 mm dia Pipe

40 mm dia Pipe

32 mm dia Pipe

25 mm dia Pipe

Providing and fixing Cast Iron Butterfly valve with SS Disc Nitrile Rubber Seal & O-Ring PN 16 pressure rating with hand lever operated including nut, bolt, flanges, gasket etc. complete as reqd.

150 mm nominal bore

100 mm nominal bore

80 mm nominal bore

50 mm nominal bore

Supplying, installing, testing and commissioning conventional Sprinkler quartzoid bulb type with 15mm screwed end connection of 68 deg. C. temperature rating,K 80 and orifice shall not be less than 6mm.Sprinklers shall be UL Listed / FM approved with Chrome finished. Pendent / Up right

Supply & fixing of approved type rosette plates ( Recessed type, in two piece) for Sprinklers below false ceiling area. AdjustableRosettePlatefor1/2"sprinklers-WhiteFinish

Stainless steel corrugated flexible pipe(hose) UL listed for dropping sprinklers below false ceiling, pipe shall be 16 bar pressure rating and 1500 mm long 25 mm dia with union / reducer collar, clamps etc. as required.

Supplying and fixing 150 mm installation valve UL listed with 24 V hooter; connection at pump room and fire console room complete with drain pipe leading to drain, cabling, pressure & flow switches,Bell etc.complete. (For sprinkler system)

Providing and fixing Ball valve (Brass) of approved quality, High or low pressure complete as directed.

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

SUB HEAD XXII: FIRE ALARM SYSTEM

Supply, installation, testing and commissioning of two-Loop Microprocessor based analogue addressable type Fire Alarm Control Panel and it should be expandaple upto 15 Loops. Each Loop should support min. 254 detectors/devices in any combination and should support minimum distance of loop 1500 mtrs.The Controller shall be with Touch screen color display, Inbuilt Network ports ((both RS485&Ethernet)) & Inbuilt Printer ports. The Panel shall be UL/VDS/EN 54 approved. cost shall be included with required software, license, associated card , cable & hardware as completed.

Supply, Installation, Testing & Commissioning of Fire Command Station including Graphical User Interface Software. The GUI based main network software shall be capable of graphically representing each node being monitored with floor plans and icons depicting the actual locations of the various systems; and / or sensors’ locations. The GUI software shall be located in control room and shall monitor all the blocks panel connected with each other. The software shall provide the facility to Monitor over Fire Network along with the Fire detection signal. cost shall be included with required software, license, associated card , cable & hardware as completed.

Supply, Installation, Testing & Commissioning of Bacnet Gateway for Integration with BMS System. The BACNET Gateway shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation (failure of CPU shall not result in failure of BACNET Gateway). cost shall be included with required software, license, associated card , cable & hardware as completed.

Supply, Installation, Testing and Commissioning of intelligent addressable Multicriteria detector works based on Dual-Ray technology with an infrared and a blue LED so that lightest smoke is detected fast and reliable along with a heat sensor including mounting base.. Detetctor should have inbuilt dual fault isolators as per NFPA 72 style 7 wiring requirements and have an option of both soft & hard addressing. Detector should have drift compensation feature & integrated EMI/EMC circuit to monitor Electromagnetic interference and report to the panel - current and average values. EMC safety for detector shall be 50 V/m. Should have Vds/ EN54/ UL & FM Certification. along with GI powder coated metal box along with all fixing accessories.

Supply, Installation, Testing and Commissioning of addressable Heat detector with fixed temp. and rate of raisetemp. feature including mounting base with LED… etc.Detetctor should have inbuilt dual fault isolators as per NFPA 72 style 7 wiring requirements and have an option of both soft & hard addressing. Detector should have drift compensation feature & integrated EMI/EMC circuit to monitor Electromagnetic interference and report to the panel - current and average values. EMC safety for detector shall be 50 V/m. Should have Vds/ EN54/ UL & FM Certification. along with GI powder coated metal box along with all fixing accessories.

Supply, Installation, Testing and Commissioning of addressable smoke detector including mounting base with LED…Detetctor should have inbuilt dual fault isolators as per NFPA 72 style 7 wiring requirements and have an option of both soft & hard addressing. Detector should have drift compensation feature & integrated EMI/EMC circuit to monitor Electromagnetic interference and report to the panel - current and average values. EMC safety for detector shall be 50 V/m. Should have Vds/ EN54/ UL & FM Certification. along with GI powder coated metal box along with all fixing accessories.

Supply, installation, testing & commissioning of analogue CO2 detectors with base, inbuilt isolator, LED indication lamp and GI powder coated metal box along with all fixing accessories.

Supply, Installation, Testing and Commissioning of Beam detector incuding mounting base along with Interface module to direct connnect to the loop , having a coverage area with a distance of min. 10 m and max. 100 m with extra width of up to 14 m ,Operating temperature range: -20 C to +55 C. required accessories, module, mounting details etc to be incluided as complete.

Supply, installation, testing & commissioning of LPG Gas detectors with base, inbuilt isolator, LED indication lamp and GI powder coated metal box along with all fixing accessories.

Supply, installation, testing and commissioning of analogue addressable manual break glass unit ( Double action) with inbuilt isolators and GI powder coated metal box along with all fixing accessories.

Supply, installation, testing and commissioning of 2.5 KM range Siren with Weather proof motor with 220V 50HZ AC Supply operation with required power contactor, MPCB for control all in a weather proof enclosure near motor including all fixing accessories, complete as required.

Supply, Installation, Testing and Commissioning of Conventional Interface Modules with inbuilt dual fault isolators as per NFPA 72 style 7 wiring requirements, Conventional Interface Modules allow conventional detectors to be connected via a 4‑wire supply networkI. Should have Vds/ EN54/ UL & FM Certificationand GI powder coated metal box along with all fixing accessories.

Supply, Installation, Testing and Commissioning of Addressable Control Relay Module with inbuilt dual fault isolators as per NFPA 72 style 7 wiring requirements & with flexible network structures with a maximun switching current of 1A @ 30V DC. Should have Vds/ EN54/ UL & FM Certification and GI powder coated metal box along with all fixing accessories.

Supply, installation, testing and commissioning of Response indicators with LED indication lamp along with all fixing accessories, complete as required.

Supply, Installation, Testing and Commissioning of Active Repeater panel to be connected peer to peer with Main Fire Alarm panel. Accept, Reset functions shall be possible from the repeater panel. The HMI of the Main panel and the Repeater panel shall be similar including keypad. All other specification shall remain unchanged like FACP. Should have Vds/ EN54/ UL & FM Certification.. cost shall be included with required software, license, associated card , cable & hardware as completed.

Supply and fixing of LED Exit Light fixtures with min. 2.0 hrs. battery back up, non maintenance type with all fixing accessories.

Supply, laying & testing of twisted pair 1.5 sq. mm. shielded FRLS insulated copper conductor armoured cable in existing PVC/ GI conduit or surface of ceiling with clamp, complete as required.

Supply and laying of 3core x 2.5sq.mm copper conductor FRLS insulated armoured cable laid on wall / ceiling including clamp/spacers etc. complete as required.

Supply and laying of 4core x 1.5sq.mm copper conductor FRLS insulated armoured cable or suitable cable for interconnecting Main Fire Alarm Control Panel to Fire Alarm Repeater Panel laid on cable trays / wall / ceiling or in pipe including clamp/spacers etc. complete as required.

Supply and laying of 50 mm dia. class B GI pipes for road crossing, laid 600mm below ground level including excavation, back filling etc., complete as required.

SUB HEAD XXIII: INTERNAL ELECTRIFICATION

Supply Installation Testing and commissioning of TPN MCB Double door Distribution boards (IP 43) dust and vermin protected and rated for 415V Three Phase AC supply operation including incoming MCB /ELCB as per specifications and required capacity Neutral bar and Earth terminal complete as required and installed in flush with wall including all fixing materials required. MCBs shall conform to IS : 8828 and ELCB shall conform to IS :12640. All MCBs shall be 'C' Curve.

6 Way TPN MCB DB with 40-63A, 4P MCB as incomer, 3nos. 40-63A DP RCCBs, 100mA as sub incomer and 18nos 6-32A SP MCBs as outgoings.

8 Way TPN MCB DB with 40-63A, 4P MCB as incomer, 3nos. 40-63A DP RCCBs, 100mA as sub incomer and 24nos 6-32A SP MCBs as outgoings.

12 Way TPN MCB DB with 40-63A, 4P MCB as incomer, 3nos. 40-63A DP RCCB, 100mA as sub incomer and 36nos 6-32A SP MCBs as outgoings.

16 Way SPN MCB DB with 25-40-63A, DP RCBO, 100mA as incomer and 12nos 6-32A SP MCBs outgoings.

12 Way SPN MCB DB with 25-40-63A, DP RCBO, 100mA as incomer and 8nos 6-32A SP MCBs outgoings.

8 Way SPN MCB DB with 25-40-63A, DP RCBO, 100mA as incomer and 4nos 6-32A SP MCBs outgoings.

4 Way TPN Vertical MCB DB with 40-63A, 4P RCBO, 100mA as incomer and 12nos 6-32A SP MCBs or 4nos. 6-40A TP MCBs or any combination as outgoings.

8 Way TPN Vertical MCCB DB with 125A 4P MCCB (M.P. Based with LSIG protection) as incomer and 12nos 6-32A SPMCBs and 5nos 6-40-63A TP MCBs as outgoings or any combinations (Vertical PDBs)

8 Way TPN Vertical MCB DB with 40-63A, 100mA 4Pole RCBO as incomer and 24nos 6-32A SPMCBs and 8nos 6-40A TP MCBs as outgoings or any combinations (Vertical PDBs)

12 Way TPN Vertical MCCB DB with 125A 4P MCCB (M.P. Based with LSIG protection) as incomer and 12nos 6-32A SPMCBs and 8nos 6-40A TP MCBs as outgoings or any combinations (Vertical PDBs)

SWITCHGEARS Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

100A, 36KA, FP MCCB

125A, 36KA, FP MCCB

200A, 36KA, FP MCCB

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 100 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 100 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supply, installation, testing & commissioning of factory made 20-40-63A 4P RCBO, 300mA in factory made outdoor and weatherproof enclosure (IP 65) equivalent to Make : Legrand, Cat No. Plexo, complete as required.

Supply, installation, testing & commissioning of factory made 20-40-63A DP MCB, 10kA in factory made outdoor and weatherproof enclosure (IP 65) equivalent to Make : Legrand, Cat No. Plexo, complete as required.

Supply, installation, testing & commissioning of factory made 20-40-63A TPN MCB, 10kA in factory made outdoor and weatherproof enclosure (IP 65) equivalent to Make : Legrand, Cat No. Plexo, complete as required.

Supply, installation, testing & commissioning of factory made 20-40-63A DP RCBO, 100mA in factory made outdoor and weatherproof enclosure (IP 65) equivalent to Make : Legrand, Cat No. Plexo, complete as required.

SUB MAINS Supply and wiring with the following size 1100V grade FRLS insulated multistranded copper conductor wires in & including suitable size heavy gauge PVC conduit concealed in wall / Ceiling including all accessories such as junction boxes, bends, elbows including and terminated with suitable lugs.

2 runs of 2.5 sq.mm wires with 1 run of 2.5 sq.mm in 25mm dia conduit

2 runs of 4 sq.mm wires with 1 run of 4 sq.mm in 25mm dia conduit

2 runs of 6 sq.mm wires with 1 runs of 6 sq.mm in 25mm dia Conduit

4 runs of 4 sq.mm wires with 2 runs of 4 sq.mm in 32mm dia conduit

2 runs of 10 sq.mm wires with 1 runs of 10 sq.mm in 32mm dia conduit

2 runs of 16 sq.mm wires with 1 runs of 16 sq.mm in 32mm dia conduit

3Core 2.5 Sq. mm. copper flexible cable in 25mm dia Conduit

3Core 4 Sq. mm. copper flexible cable in 25mm dia conduit

Power Wiring Point wiring for light points, fan points, exhaust fan points, 6A plug and socket with 2 runs of 1.5 Sq. mm FRLS PVC insulated, multistranded, copper wires of 1100V grade laid in and including 20 mm dia. heavy gauge PVC conduit in concealed in ceiling / walls conforming to IS 732 including one run of 1.5 sq.mm FRLS PVC insulated, multistranded, copper earth wire of 1100V grade including all accessories such as junction boxes, conduit bends, elbows and ceiling rose, anodised GI switch box with modular switch and the box covered with front plate. Cutting, chases in wall and making them good after fixing modular type switches as per requirement in sheet steel boxes of adequate sizes to accommodate switches, sockets, electronic fan regulator etc. (Including sub main wiring of 2 runs of 2.5 sq.mm & 1 x 2.5 sq.mm FRLS PVC insulated, multistranded, copper wires of 1100V grade in 25 mm dia heavy gauge PVC conduit with conduit accessories etc. complete as required).

a) One light point controlled by one 6A switch.

b) Two light points controlled by one 6A switch.

c) Three light points controlled by one 6A switch.

d) Four light points controlled by one 6A switch.

e) Five light points controlled by one 6A switch.

f) Six light points controlled by one 6A switch.

g) Seven light points controlled by one 6A switch.

h) Eight light points controlled by one 6A switch.

i) Nine light points controlled by one 6A switch.

j) Ten light points controlled by one 6A switch.

k) One light point controlled by two nos. 6A two way switches

l) Two light points controlled by two nos. 6A two way switches

m) Three light points controlled by two nos. 6A two way switches

n) One exhaust fan point controlled by one 6A switch

o) One Ceiling fan point controlled by one 6A switch including one 100W step type (two module) electronic regulator and MS fan hook box.

p) One 3 pin 6A plug socket controlled by one 6A switch (Dependant)

CABLE TRAY Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required shall conforms to IS: 61537

150mmX 50mmX 1.6mm thickness

300mmX 62.50mmX 2mm thickness

450mmX 62.50mmX 2mm thickness

SWITCH SOCKETS Supply, installation, testing and commissioning of 6A, 5 pin shuttered type socket outlet controlled by one 6A modular switch of combination type with indication lamp in and including anodised GI box, front plate complete with fixing accessories and 2runs of 2.5sq.mm FRLS insulated multistranded copper conductor wires, 1run of 2.5 sq.mm earth wires laid in and including heavy gauge 25mm dia PVC conduit concealed in wall/ ceiling along with required accessories including all accessories such as junction boxes, conduit bends, elbows and ceiling rose. Cutting, chases in wall and making them good after fixing modular type switches as per requirement in sheet steel boxes of adequate sizes to accommodate switches, sockets, etc. as required. (Maximum 5 nos. sockets can be looped in one circuit from DB)

Supply, installation, testing and commissioning of 6/16A, 5 pin shuttered type socket outlet controlled by one 16A modular switch of combination type with indication lamp in and including anodised GI box, front plate complete with fixing accessories and 2runs of 2.5sq.mm FRLS insulated multistranded copper conductor wires, 1run of 2.5 sq.mm earth wires laid in and including heavy gauge 25mm dia PVC conduit concealed in wall/ ceiling along with required accessories including all accessories such as junction boxes, conduit bends, elbows and ceiling rose. Cutting, chases in wall and making them good after fixing modular type switches as per requirement in sheet steel boxes of adequate sizes to accommodate switches, sockets, etc. as required. (Maximum 3 nos. sockets can be looped in one circuit from DB)

Supply, installation, testing and commissioning of 6/16A, 5 pin shuttered type socket outlet controlled by one 16A modular switch of combination type with indication lamp (switch & socket at different location) in and including anodised GI box, front plate complete with fixing accessories and 2runs of 2.5sq.mm FRLS insulated multistranded copper conductor wires, 1run of 2.5 sq.mm earth wires laid in and including heavy gauge 25mm dia PVC conduit concealed in wall/ ceiling along with required accessories including all accessories such as junction boxes, conduit bends, elbows and ceiling rose. Cutting, chases in wall and making them good after fixing modular type switches as per requirement in sheet steel boxes of adequate sizes to accommodate switches, sockets, etc. as required. (AC Indoor Unit Point) (Maximum 3 nos. sockets can be looped in one circuit from DB)

Supply, installation, testing and commissioning of 25A, 5 pin shuttered type socket outlet controlled by one 25A modular switch of combination type with indication lamp in and including anodised GI box, front plate complete with fixing accessories and 2runs of 4.0sq.mm FRLS insulated multistranded copper conductor wires, 1run of 4.0 sq.mm earth wires laid in and including heavy gauge 25mm dia PVC conduit concealed in wall/ ceiling along with required accessories including all accessories such as junction boxes, conduit bends, elbows and ceiling rose. Cutting, chases in wall and making them good after fixing modular type switches as per requirement in sheet steel boxes of adequate sizes to accommodate switches, sockets, etc. as required. (Only one socket can be looped in one circuit from DB)

Supply, installation, testing and commissioning of 32A, 5 pin shuttered type socket outlet controlled by one 32A modular switch of combination type with indication lamp (switch & socket at different location) in and including anodised GI box, front plate complete with fixing accessories and 2runs of 4.0sq.mm FRLS insulated multistranded copper conductor wires, 1run of 4.0 sq.mm earth wires laid in and including heavy gauge 25mm dia PVC conduit concealed in wall/ ceiling along with required accessories including all accessories such as junction boxes, conduit bends, elbows and ceiling rose. Cutting, chases in wall and making them good after fixing modular type switches as per requirement in sheet steel boxes of adequate sizes to accommodate switches, sockets, etc. as required. (Only one socket can be looped in one circuit from DB)

Supply, installation, testing and commissioning of 3nos. 6A, 5 pin shuttered type socket outlet controlled by one 16A modular switch of combination type with indication lamp in and including anodised GI box, front plate complete with fixing accessories and 3core 2.5sq.mm FRLS insulated multistranded copper flexible cable laid in and including heavy gauge 25mm dia PVC conduit concealed in wall/ ceiling along with required accessories including all accessories such as junction boxes, conduit bends, elbows and ceiling rose. Cutting, chases in wall and making them good after fixing modular type switches as per requirement in sheet steel boxes of adequate sizes to accommodate switches, sockets, etc. as required. All UPS power switch, sockets and front plate's colour shall be different than Raw power. Colour : Grey/ Black. (Maximum 3 nos. sockets can be looped in one circuit from DB)

Supply, installation, testing and commissioning of 6/16A, 5 pin shuttered type socket outlet controlled by one 16A modular switch of combination type with indication lamp in and including anodised GI box, front plate complete with fixing accessories and 3core 2.5sq.mm FRLS insulated multistranded copper flexible cable laid in and including heavy gauge 25mm dia PVC conduit concealed in wall/ ceiling along with required accessories including all accessories such as junction boxes, conduit bends, elbows and ceiling rose. Cutting, chases in wall and making them good after fixing modular type switches as per requirement in sheet steel boxes of adequate sizes to accommodate switches, sockets, etc. as required. All UPS power switch, sockets and front plate's colour shall be different than Raw power. Colour : Grey/ Black. (Maximum 3 nos. sockets can be looped in one circuit from DB)

TV antenna socket outlet

Telephone socket outlet

Supplying and fixing following size/ modules, Gl box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mmX150mm)

LIGHT FIXTURES Supplying and erecting 18-20W, LED surface mounted light fitting with extuded aluminium body & plastic end caps Luminaire Efficacy- 100 lm/W Lumen Flux- 2000 lm Color Rendering Index- >80 Built-in Surge protection- 3 Kv with all fixing accessories.

Supplying and erecting 7-10W, LED surface mounted Polycarbonate co-extrusion tubelight housing with engg-plastic end caps.Luminaire Efficacy- 100 lm/W Lumen Flux- 1000 lm Color Rendering Index- >80 Built-in Surge protection- 4 kV with all fixing accessories.

Supplying & erecting of 10-12W, 230V integral type LED Lamp suitable for B?22/E-27 base with all fixing accessories.

Supplying and erecting LED Rimless square / circular Max. 10-12 W down lighter Aluminium housing comprising of LED’s.& Housing: White powder coated.Luminaire efficacy - 100 lm/W Luminous flux- 1200 lm Built-in Surge protection- 4kV with all fixing accessories.

Supplying and erecting LED 2x2 Ceiling Lig ht Luminaire with visual comfort having wattage not more than 34-36W CRCA sheet housing.Luminous flux3600 lm 100 lm/W lumen/W, CRI>80, CCT upto 5000K, THD@240V <10% with all fixing accessories.

Supplying and erecting LED Ceiling Light Luminaire with visual comfort having wattage not more than 22-24W CRCA sheet housing.Luminous flux 2400 lm 100 lm/W lumen/W, CRI>80, CCT upto 5700K, THD@240V <10% Power Factor ≥0.90

Supplying and erecting VISUAL COMFORT DOWNLIGHT Recessed fixture having wattage not more than 15-20 W with dimmable driver Luminous flux 1750 lm 100 lm/W lumen/W,CRI 80 low glare with all fixing accessories.

Supplying and erecting VISUAL COMFORT DOWNLIGHT Surface fixture having wattage not more than 15-20 W with dimmable driver Luminous flux 1620 lm 90 lm/W lumen/W,CRI 80 low glare with all fixing accessories.

Supplying and erecting LED 2x2 Ceiling Light Luminaire with visual comfort having wattage not more than 22-24W CRCA sheet housing. Luminous flux 2400 lm 100 lm/W lumen/W, CRI>80, CCT upto 5700K, THD@240V <10% Power Factor ≥0.95 with all fixing accessories.

Supplying and erecting 80W, suspended decorative circular light fittingPressure die-cast aluminum housing and nonintegratedL ED driver compartment Eye-bolt provided for suspension mounting.Luminaire efficacy* 150 lm/WColorCCT uupto 5700K IP65 with all fixing accessories.

Supplying and erecting 10W, LED surface mounted Bulkhead Light Fitting with powder coated pressure die-cast aluminium alloy. Lumen Flux 800lm Luminaire Efficacy 80 lm/W Color Rendering Index 80 Built-in Surge protection 2.5 kV with all fixing accessories.

Supplying and erecting 7-9W LED Step Light Fitting for ramp, steps etc. of dimensions - 137x107x83mm (+/-5%), luminaire made of extruded aluminium alloy, finished with pure polyester powder coated graphite grey, (IP-67) protection, lumens output of the luminaire : minimum 63 lm Impact Protection IK06 Built-in Surge protection 4 kV with all fixing accessories.

Supplying and erecting VISUAL COMFORT DOWNLIGHT for passage Recessed fixture having wattage not more than 12-15 W efficacy 130 lm/W CRI 90 Low gare with all fixing accessories.

Supplying and erecting 7-9W COB downlight with dimmable driver White powder coated recess mounting pressure die-cast aluminium housing. Ingress protection : IP20 with all fixing accessories.

Supplying and erecting 15W, LED surface mounted circular Down light fitting with die-cast aluminum housing in white powder coating finish, anti-glare diffuser, lumens output of the luminaire : minimum 1500 Lumens. with all fixing accessories.

Supplying and erecting Squash Light 2x2 surface mounting fixture CRCA steel sheet housing comprising of LED’s connected in series parallel. System Wattage 36W Luminaire efficacy 100 lm/W Built-in Surge protection 3 kV with all fixing accessories.

Supplying and erecting Badminton light 40W, LED surface mounted light fitting with extuded aluminium body & plastic end caps Luminaire Efficacy- 100 lm/W Lumen Flux- 4000 lm Color Rendering Index- >80 Built-in Surge protection- 3 kV with all fixing accessories.

Supplying and erecting LED Exit Light fixtures with min. 2.0 hrs Nickel-Cadmium battery back-up wall/ ceiling/ suspended as required, double sided legend with all fixing accessories.

Supplying and erecting 150W White Flood Light for Playing Area Graphite grey powder coated aluminium die-cast housing. Luminous flux** 18,000 lm Luminaire efficacy* 120 lm/W Color Rendering Index >70 Built-in Surge protection 4 kV External Surge Protection 10 kV Ingress Protection IP66 Mechanical impact protection IK08 with all fixing accessories.

Supplying and erecting 200W White Flood Light for Playing Area Graphite grey powder coated aluminium die-cast housing. Luminous flux** 24,000 lm Luminaire efficacy* 120 lm/W Color Rendering Index >70 Built-in Surge protection 4 kV External Surge Protection 10 kV Ingress Protection IP66 Mechanical impact protection IK08 with all fixing accessories.

Supplying and erecting 250W White Flood Light for Playing Area Graphite grey powder coated aluminium die-cast housing.Luminous flux** 30,000 lmLuminaire efficacy* 120 lm/WColor Rendering Index >70Built-in Surge protection 4 kVExternal Surge Protection 10 kVIngress Protection IP66Mechanical impact protection IK08 with all fixing accessories.

Supplying and erecting 350W White Flood Light for Playing Area Graphite grey powder coated aluminium die-cast housing. Luminous flux** 42,000 lm Luminaire efficacy* 120 lm/W Color Rendering Index >70 Built-in Surge protection 4 kV External Surge Protection 10 kV Ingress Protection IP66 Mechanical impact protection IK08

Supplying and erecting 5W/1M Strip Light for Cove for Conference Strip Light with all fixing accessories.

Supplying, Installation, Testing & erecting of Occupancy Sensor of Minimum 6 Meter Radius with standard Mounting Accessories as required.

Supplying, Installation, Testing & erecting of LUX Sensor of Minimum 6 Meter Radius with standard Mounting Accessories as required.

Supplying, Installation, Testing & erecting of Occupancy + Lux Sensor of Minimum 6 Meter Radius with standard Mounting Accessories as required.

FANS Supply, Installation, testing & commissioning of Exhaust fans of 250mm size sweep with gravity louvers shutters including making appropriate size of hole finish in shape and other civil engineering works make them good after installation, 3C x 1.5sqmm flexible cable from ceiling rose up to fan and all fixing accessories/ hardware of materials as required. (Make : Orient/ equivalent)

Supply, Installation, testing & commissioning of Exhaust fans of 305mm size sweep with gravity louvers shutters including making appropriate size of hole finish in shape and other civil engineering works make them good after installation, 3C x 1.5sqmm flexible cable from ceiling rose up to fan and all fixing accessories/ hardware of materials as required. (Make : Orient/ equivalent)

Supply, Installation, testing & commissioning of Exhaust fans of 450mm size sweep with gravity louvers shutters including making appropriate size of hole finish in shape and other civil engineering works make them good after installation, 3C x 1.5sqmm flexible cable from ceiling rose up to fan and all fixing accessories/ hardware of materials as required shall conform to IS :60335-2-80.

a) 1200mm Sweep, 5 Star Energy Efficient, white colour ceiling fan including down rod, blades with all accessories excluding regulator etc., complete.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Providing and fixing standard size ISI certified Electrical storage water heater with rated wattage 2kw, 230V,50Hz,Single Phase, 1/2 inch inlet outlet connection, SS tank and 4 star energy rating with thermostat feature, Glass lined inner tank and heating element with safety valve etc complete including all the items metioned as below. Provisional 25 Ltrs capacity Angle stop cock CON 059KN

Providing and fixing Water Cooler with Inbuilt RO water purification system including necessary inlet/outlets, CP angle stop cock & making drain connection as per req. Purified Water Production Capacity :- 80 LPH Storage Capacity :- 120 L

SUB HEAD XIV: SHOP ELECTRICAL

ISOLATOR PANEL Breaker 2500A FP ACB EDO and LSIG Protection, 50 kA -1NO with Indication Lamp, Breaker control switch as per Tender Specification.

1 No.4000 Amp 415 volt grade, 50 kA 4P EDO ACB each complete with Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay and instantaneous along with earth fault protection. 230 V AC spring charging motor and closing coil. Shunt trip coil 24 V DC and under voltage coil 230 V AC. Safety shutter & 6 NO + 6 NC contacts. 3 nos cast resin current transformer of 4000/5 (for DG SYNC) ratio class 1.0 for metering, 15 VA Burden. Multifunction meter communication Port RS-485 with 1 set of three RYB indicating lamps. Red/green/amber ON/OFF/Trip indicating lamps. Spring charge indication lamp. Breaker control switch. 1 Set PT 415/root3V/110/root3 V; 100 VA; class 1.0 Under voltage relay (27)-415 VAC. Over voltage relay (59)-415 V AC Illuminated push button for healthy circuit. TRANSFORMER INCOMING (2 No.) BUSBARS TPN aluminium bus bars of minimum 4000 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 50 KA for 1 sec.

BUSBARS TPN aluminium bus bars of minimum 2500 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 50 KA for 1 sec. BUSCOUPLER 2 No.2500 Amp 415 volt grade, 50 kA 4P EDO ACB each complete with Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay and instantaneous along with earth fault protection. 230 V AC spring charging motor and closing coil. Shunt trip coil 24 V DC and under voltage coil 230 V AC. Safety shutter & 6 NO + 6 NC contacts. Red/green/amber ON/OFF/Trip indicating lamps. OUTGOINGS: 63A FP MCCB 16 KA-1NO 100A FP MCCB 25 KA-2NO 200A FP MCCB25 KA-1NO 400A FP MCCB 35 KA-1NO 630A FP ACB 35 KA-6NO 800A FP ACB 50 KA-2NO 1000A FP ACB 50 KA -4NO

BUSBARS TPN aluminium bus bars of minimum 630 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 50 KA for 1 sec. 250A FP MCCB 35 KA-1NO 400A FP MCCB 35 KA-1NO Note All outgoing MCCBs shall be MP based with adjustable and inbuilt O/L & S/C,E/Fprotection. All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

APFC PANEL Supplying, erecting, testing & commisioning 510 kVAr, 3 phase, 50 Hz., APFC Panel with derated power contactor of suitable rating for capacitor switching Application for each step controlled by microprocessor based APFC relay consisting of suitable steps of MPP /APP type capacitor with 525 V and having minimum overcurrent capacity of 1.8 In, peak inrush current capacity 300 In and minimum life 150000 hours with detuned aluminium wound reactor of 7/ 14% for each step, APFC Panel shall suitable rating ACB/MCCB as incomer and each branch/step shall have separate isolation with MCCB/MCB of The panel shall consist of IP42 rating, compliance to IEC 61439 and power quality IEC 61921 standard.

1 No.800 Amp 415 volt grade, 36kA 4P EDO ACB each complete with Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay and instantaneous along with earth fault protection. 230 V AC spring charging motor and closing coil. Shunt trip coil 24 V DC and under voltage coil 230 V AC. Safety shutter & 6 NO + 6 NC contacts. 3 nos cast resin current transformer of 800/5 (for 500 KVA DG) ratio class 1.0 for metering, 15 VA Burden. Multifunction meter communication Port RS-485 with 1 set of three RYB indicating lamps. Red/green/amber ON/OFF/Trip indicating lamps. Spring charge indication lamp. Breaker control switch. 1 Set PT 415/root3V/110/root3 V; 100 VA; class 1.0 Under voltage relay (27)-415 VAC. Over voltage relay (59)-415 V AC Illuminated push button for healthy circuit.

1 No.2000 Amp 415 volt grade, 36kA 4P EDO ACB each complete with Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay and instantaneous along with earth fault protection. 230 V AC spring charging motor and closing coil. Shunt trip coil 24 V DC and under voltage coil 230 V AC. Safety shutter & 6 NO + 6 NC contacts. 3 nos cast resin current transformer of 2000/5 (for 1250 KVA DG) ratio class 1.0 for metering, 15 VA Burden. Multifunction meter communication Port RS-485 with 1 set of three RYB indicating lamps. Red/green/amber ON/OFF/Trip indicating lamps. Spring charge indication lamp. Breaker control switch. 1 Set PT 415/root3V/110/root3 V; 100 VA; class 1.0 Under voltage relay (27)-415 VAC. Over voltage relay (59)-415 V AC Illuminated push button for healthy circuit. BUSBARS TPN aluminium bus bars of minimum 4000 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 50 KA for 1 sec. OUTGOING 4000A FP ACB-1NO

Note All outgoing MCCBs shall be MP based with adjustable and inbuilt O/L & S/C,E/Fprotection All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

INCOMER 1 No.800 Amp 415 volt grade, 36kA 4P EDO ACB each complete with Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay and instantaneous along with earth fault protection. 230 V AC spring charging motor and closing coil. Shunt trip coil 24 V DC and under voltage coil 230 V AC. Safety shutter & 6 NO + 6 NC contacts. 3 nos cast resin current transformer of 800/5 ratio class 1.0 for metering, 15 VA Burden. Multifunction meter communication Port RS-485 with 1 set of three RYB indicating lamps. Red/green/amber ON/OFF/Trip indicating lamps. Spring charge indication lamp. Breaker control switch. 1 Set PT 415/root3V/110/root3 V; 100 VA; class 1.0 Under voltage relay (27)-415 VAC. Over voltage relay (59)-415 V AC Illuminated push button for healthy circuit. BUSBARS TPN aluminium bus bars of minimum 800 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 36KA for 1 sec.

OUTGOING 630A FP MCCB 35 KA- 1NO 315A FP MCCB 35 KA- 2NO 200A FP MCCB 25 KA- 2NO 100A FP MCCB 25 KA- 2NO 63A FP MCB 16 KA- 2NO Note Provide Provision for higher rating of Outgoing MCCB - 2 nos All outgoing MCCBs shall be TMD based with adjustable and inbuilt O/L & S/C protection. All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

BUSBARS TPN Copper bus bars with Double Neutral of minimum 315 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 36 KA for 1 sec. OUTGOING 250A FP MCCB 35KA- 1NO 100A FP MCCB 25KA- 2NO 63A FP MCB 16KA- 3NO Note Provide Provision for higher rating of Outgoing MCCB - 2 nos All outgoing MCCBs shall be TMD based with adjustable and inbuilt O/L & S/C protection. All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

INCOMER 1 No.630 Amp 415 volt grade, 36kA 4P EDO ACB each complete with Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay and instantaneous along with earth fault protection. 230 V AC spring charging motor and closing coil. Shunt trip coil 24 V DC and under voltage coil 230 V AC. Safety shutter & 6 NO + 6 NC contacts. 3 nos cast resin current transformer of 630/5 ratio class 1.0 for metering, 15 VA Burden. Multifunction meter communication Port RS-485 with 1 set of three RYB indicating lamps. Red/green/amber ON/OFF/Trip indicating lamps. Spring charge indication lamp. Breaker control switch. 1 Set PT 415/root3V/110/root3 V; 100 VA; class 1.0 Under voltage relay (27)-415 VAC. Over voltage relay (59)-415 V AC Illuminated push button for healthy circuit. BUSBARS TPN aluminium bus bars of minimum 630 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 36KA for 1 sec.

OUTGOING 400A FP MCCB 35KA- 1NO 250A FP MCCB 35 KA- 1NO 100A FP MCCB 25KA- 5NO 63A FP MCB 16KA- 4NO Note Provide Provision for higher rating of Outgoing MCCB - 2 nos All outgoing MCCBs shall be TMD based with adjustable and inbuilt O/L & S/C protection All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

BUSBARS TPN Copper bus bars with Double Neutral of minimum 125 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 25 KA for 1 sec. OUTGOING 100A FP MCCB 25KA- 1NO 63A FP MCB 16KA - 3NO Note Provide Provision for higher rating of Outgoing MCCB - 2 nos All outgoing MCCBs shall be TMD based with adjustable and inbuilt O/L & S/C protection. All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

INCOMER 1 No.630 Amp 415 volt grade, 36kA 4P EDO ACB each complete with Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay and instantaneous along with earth fault protection. 230 V AC spring charging motor and closing coil. Shunt trip coil 24 V DC and under voltage coil 230 V AC. Safety shutter & 6 NO + 6 NC contacts. 3 nos cast resin current transformer of 630/5 ratio class 1.0 for metering, 15 VA Burden. Multifunction meter communication Port RS-485 with 1 set of three RYB indicating lamps. Red/green/amber ON/OFF/Trip indicating lamps. Spring charge indication lamp. Breaker control switch. 1 Set PT 415/root3V/110/root3 V; 100 VA; class 1.0 Under voltage relay (27)-415 VAC. Over voltage relay (59)-415 V AC Illuminated push button for healthy circuit. BUSBARS TPN aluminium bus bars of minimum 630 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 36KA for 1 sec.

OUTGOING 400A FP MCCB 35KA- 1NO 200A FP MCCB 25KA- 1NO 100A FP MCCB 25KA- 5NO 63A FP MCB 16 KA- 4NO Note Provide Provision for higher rating of Outgoing MCCB - 2 nos All outgoing MCCBs shall be TMD based with adjustable and inbuilt O/L & S/C protection. All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

BUSBARS TPN Copper bus bars with Double Neutral of minimum 125 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 25 KA for 1 sec. OUTGOING 100A FP MCCB 25KA- 1NO 63A FP MCB 16KA- 3NO Note Provide Provision for higher rating of Outgoing MCCB - 2 nos All outgoing MCCBs shall be TMD based with adjustable and inbuilt O/L & S/C protection All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

INCOMER 1 No.630 Amp 415 volt grade, 36kA 4P EDO ACB each complete with Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay and instantaneous along with earth fault protection. 230 V AC spring charging motor and closing coil. Shunt trip coil 24 V DC and under voltage coil 230 V AC. Safety shutter & 6 NO + 6 NC contacts. 3 nos cast resin current transformer of 630/5 ratio class 1.0 for metering, 15 VA Burden. Multifunction meter communication Port RS-485 with 1 set of three RYB indicating lamps. Red/green/amber ON/OFF/Trip indicating lamps. Spring charge indication lamp. Breaker control switch. 1 Set PT 415/root3V/110/root3 V; 100 VA; class 1.0 Under voltage relay (27)-415 VAC. Over voltage relay (59)-415 V AC Illuminated push button for healthy circuit. BUSBARS TPN aluminium bus bars of minimum 630 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 36KA for 1 sec.

OUTGOING 315A FP MCCB 35KA- 1NO 200A FP MCCB 25KA- 1NO 100A FP MCCB 25KA- 4NO 63A FP MCB 16KA- 12NO Note Provide Provision for higher rating of Outgoing MCCB - 2 nos. All outgoing MCCBs shall be TMD based with adjustable and inbuilt O/L & S/C protection. All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

BUSBARS TPN Copper bus bars with Double Neutral of minimum 125 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 25 KA for 1 sec. OUTGOING 100A FP MCCB 25 KA- 1NO 63A FP MCB 16 KA- 3NO Note Provide Provision for higher rating of Outgoing MCCB - 2 nos All outgoing MCCBs shall be TMD based with adjustable and inbuilt O/L & S/C protection. All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

INCOMER 1 No.630 Amp 415 volt grade, 36kA 4P EDO ACB each complete with Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay and instantaneous along with earth fault protection. 230 V AC spring charging motor and closing coil.Shunt trip coil 24 V DC and under voltage coil 230 V AC. Safety shutter & 6 NO + 6 NC contacts. 3 nos cast resin current transformer of 630/5 ratio class 1.0 for metering, 15 VA Burden Multifunction meter communication Port RS-485 with 1 set of three RYB indicating lamps. Red/green/amber ON/OFF/Trip indicating lamps. Spring charge indication lamp. Breaker control switch. 1 Set PT 415/root3V/110/root3 V; 100 VA; class 1.0 Under voltage relay (27)-415 VAC. Over voltage relay (59)-415 V AC Illuminated push button for healthy circuit. BUSBARS TPN aluminium bus bars of minimum 630 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 36KA for 1 sec.

OUTGOING 200A FP MCCB 25 KA- 1NO 100A FP MCCB 25 KA - 4NO 63A FP MCB 16 KA- 3NO Note Provide Provision for higher rating of Outgoing MCCB - 2 nos All outgoing MCCBs shall be TMD based with adjustable and inbuilt O/L & S/C protection. All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

BUSBARS TPN aluminium bus bars of minimum 400 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 36 KA for 1 sec. OUTGOING 100A FP 25KA TMD based MCCB -4NO 200A FP 25KA TMD basedMCCB -2NO

BUSBARS TPN aluminium bus bars of minimum 400 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 36 KA for 1 sec. OUTGOING 100A FP 25KA TMD based MCCB -4NO 200A FP 25KA TMD basedMCCB -2NO

RESIDENTIAL METERING PANEL (Type 2 Bldg) Supply, Installation, Testing and Commissioning of cubicle type LT panel, IP55, suitable for 415V+/- 10%, 3 Phase, 4 wire 50 Hz AC supply system fabricated in compartmentalized modular design from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having TPN Aluminium alloy bus bars for high conductivity, SMC bus bar supports,with short circuit withstand capacity of 25 KA for 1 sec , bottom base channel of MS section not less than 100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid / flexible connections from main bus bar to switchgears and from switchgear output to cable termination in cable alley with required size of AL conductors / bus bars and control wiring with 2.5 sqmm PVC insulated copper conductor cable (FRLS), cable alleys, cable gland plates in two half, i/c providing following switchgears / accessories as per specifications.

RESIDENTIAL METERING PANEL (Type 3 Bldg) Supply, Installation, Testing and Commissioning of cubicle type LT panel, IP55, suitable for 415V+/- 10%, 3 Phase, 4 wire 50 Hz AC supply system fabricated in compartmentalized modular design from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having TPN Aluminium alloy bus bars for high conductivity, SMC bus bar supports,with short circuit withstand capacity of 25 KA for 1 sec , bottom base channel of MS section not less than 100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid / flexible connections from main bus bar to switchgears and from switchgear output to cable termination in cable alley with required size of AL conductors / bus bars and control wiring with 2.5 sqmm PVC insulated copper conductor cable (FRLS), cable alleys, cable gland plates in two half, i/c providing following switchgears / accessories as per specifications.

RESIDENTIAL METERING PANEL (Type 4 Bldg) Supply, Installation, Testing and Commissioning of cubicle type LT panel, IP55, suitable for 415V+/- 10%, 3 Phase, 4 wire 50 Hz AC supply system fabricated in compartmentalized modular design from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having TPN Aluminium alloy bus bars for high conductivity, SMC bus bar supports,with short circuit withstand capacity of 36 KA for 1 sec , bottom base channel of MS section not less than 100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid / flexible connections from main bus bar to switchgears and from switchgear output to cable termination in cable alley with required size of AL conductors / bus bars and control wiring with 2.5 sqmm PVC insulated copper conductor cable (FRLS), cable alleys, cable gland plates in two half, i/c providing following switchgears / accessories as per specifications. INCOMER All Incomer Shall have TVSS Protection of CL-2 200A FP 25KA TMD based MCCB -1NO Each Incomer shall have one set of the following items: 3 Nos.phase indicating LED lamps each with 2 amp back up MCB. ON/OFF/TRIP indication lamps. Multifunction Meter

RESIDENTIAL METERING PANEL (Type 4S & 5 Bldg) Supply, Installation, Testing and Commissioning of cubicle type LT panel, IP55, suitable for 415V+/- 10%, 3 Phase, 4 wire 50 Hz AC supply system fabricated in compartmentalized modular design from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having TPN Aluminium alloy bus bars for high conductivity, SMC bus bar supports,with short circuit withstand capacity of 36 KA for 1 sec , bottom base channel of MS section not less than 100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid / flexible connections from main bus bar to switchgears and from switchgear output to cable termination in cable alley with required size of AL conductors / bus bars and control wiring with 2.5 sqmm PVC insulated copper conductor cable (FRLS), cable alleys, cable gland plates in two half, i/c providing following switchgears / accessories as per specifications.

RESIDENTIAL METERING PANEL (Type 6A,6B,& 7 Bldg) Supply, Installation, Testing and Commissioning of cubicle type LT panel, IP55, suitable for 415V+/- 10%, 3 Phase, 4 wire 50 Hz AC supply system fabricated in compartmentalized modular design from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having TPN Aluminium alloy bus bars for high conductivity, SMC bus bar supports,with short circuit withstand capacity of 36 KA for 1 sec , bottom base channel of MS section not less than 100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid / flexible connections from main bus bar to switchgears and from switchgear output to cable termination in cable alley with required size of AL conductors / bus bars and control wiring with 2.5 sqmm PVC insulated copper conductor cable (FRLS), cable alleys, cable gland plates in two half, i/c providing following switchgears / accessories as per specifications. INCOMER All Incomer Shall have TVSS Protection of CL-2 ISOLATOR - 100A FP 25ka TMD MCCB -2NO

BUSBARS TPN Copper bus bars with Double Neutral of minimum 63 Amps capacity with heat shrinkable coloured sleeves and i/c, SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 36 KA for 1 sec. OUTGOING 32A TP MCB 16 KA- 6NO Note All outgoing MCCBs shall be MP based with adjustable and inbuilt O/L & S/C,E/Fprotection All breakers breaking capacities shall be Icu=Ics upto 433 V. 1 Set Rotary operating mechanism and terminal extension spreaders for all the MCCBs. ON/OFF/TRIP indicating LED lamps each with 2 amp back up MCB. ALL Outgoing shall have Multifunction Meter

BUSBAR TRUNKING Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Bus Trunking IP 65 complying to latest IEC standards of 61439 with Plug in Feeder for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having below rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 0.8A/sqmm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required

2500 A, Isc 50kA for 1 second

2000 A, Isc 50kA for 1 second

800 A, Isc 36kA for 1 second

Supplying, erecting, testing and commissioning of Flange end with Adaptor box, as per site requirement suitable for Aluminum 3 phase 4 wire 415V, 50 Hz A.C, 36/40kA short circuit rating for 1 sec sandwich type Aluminum BBT with necessary accessories complete conforming to IEC 61439-6.

2500 A, Isc 50kA for 1 second

2000 A, Isc 50kA for 1 second

800 A, Isc 36kA for 1 second

Supplying, erecting, testing & commissioning of Vertical or Horizontal 90 degree elbow with Spring Hanger & Horizontal Bracket, for sandwich type aluminium compact bus trunking/ rising mains suitable for, 3 Phase 4 wire 415 V, 50 Hz AC supply, 36/40kA short circuit rating for 1 sec made of minimum 1.5mm thick galvanized sheet metal enclosure duly powder coated with all necessary accessories complete conforming to IEC 61439-6

2500 A, Isc 50kA for 1 second

2000 A, Isc 50kA for 1 second

800 A, Isc 36kA for 1 second

Supplying, installation, testing & commisioning of following capacity End Feed Unit for Sandwicht Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with all necessary accessories complete. 2500 A, Isc 50kA for 1 second

Supplying, installation, testing & commisioning of following capacity End Cover for Sandwicht Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with all necessary accessories complete. 2500 A, Isc 50kA for 1 second

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Bus Trunking IP 55 complying to latest IEC standards of 61439 with Plug in Feeder for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having below rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 0.8A/sqmm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required

4000 A, Isc 50kA for 1 second

630A, Isc 36kA for 1 second

Supplying, erecting, testing and commissioning of Flange end with Adaptor box, as per site requirement suitable for Aluminum 3 phase 4 wire 415V, 50 Hz A.C, 36/50kA short circuit rating for 1 sec sandwich type Aluminum BBT with necessary accessories complete conforming to IEC 61439-6.

4000 A, Isc 50kA for 1 second

630A, Isc 36kA for 1 second

Supplying, erecting, testing & commissioning of Vertical or Horizontal 90 degree elbow with Spring Hanger & Horizontal Bracket, for sandwich type aluminium compact bus trunking/ rising mains suitable for, 3 Phase 4 wire 415 V, 50 Hz AC supply, 36/50kA short circuit rating for 1 sec made of minimum 1.5mm thick galvanized sheet metal enclosure duly powder coated with all necessary accessories complete conforming to IEC 61439-6

4000 A, Isc 50kA for 1 second

630A, Isc 36kA for 1 second

Supplying, installation, testing & commisioning of following capacity End Feed Unit for Sandwicht Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with all necessary accessories complete.

4000 A, Isc 50kA for 1 second

630A, Isc 36kA for 1 second

Supplying, installation, testing & commisioning of following capacity End Cover for Sandwicht Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with all necessary accessories complete.

4000 A, Isc 50kA for 1 second

630A, Isc 36kA for 1 second

Supplying, installation, testing & commisioning of following AL Interlink for bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with all necessary accessories complete.

Supplying, installing on wall or suspension on ceiling, testing and commissioning of following capacity Air Insulated Compact Type Rising Main for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having below rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 3P4W+PE having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints, fire barrier at each floor, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required.

160 A, Isc= 36kA for 1 sec

250 A, Isc= 36kA for 1 sec

315 A, Isc= 36kA for 1 sec

400 A, Isc= 36kA for 1 sec

Supplying, erecting, testing and commissioning of Flange end as per design requirement & site condition suitable for Aluminum, 3 phase 4 wire 415V, 50 Hz A.C, 15kA short circuit rating for 0.1 sec, for Air Insulated type BBT with necessary accessories complete conforming to IEC 61439-6.

160 A, Isc= 36kA for 1 sec

250 A, Isc= 36kA for 1 sec

315 A, Isc= 36kA for 1 sec

400 A, Isc= 36kA for 1 sec

Supplying, erecting and commissioning Vertical or Horizontal 90 Degree/Tee Elbow with Spring Hanger & Horizontal Bracket for Air Insulated type bus trunking/ rising mains of capacity, 3 Phase 4 wire 415V, 50Hz AC supply, 15kA short circuit rating for 1 sec made galvanized sheet metal enclosure duly powder coated with all necessary accessories complete conforming to IEC 61439-6.

160 A, Isc= 36kA for 1 sec

250 A, Isc= 36kA for 1 sec

315 A, Isc= 36kA for 1 sec

400 A, Isc= 36kA for 1 sec

Supplying, installation, testing & commisioning of following capacity End Feed Unit for Air Insulated Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with all necessary accessories complete.

315 A, Isc= 36kA for 1 sec

400 A, Isc= 36kA for 1 sec

Supplying, installation, testing & commisioning of following capacity End Cover for Air Insulated Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with all necessary accessories complete.

160 A, Isc= 36kA for 1 sec

250 A, Isc= 36kA for 1 sec

315 A, Isc= 36kA for 1 sec

400 A, Isc= 36kA for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug Outlet Cover for Air Insulated Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with all necessary accessories complete.

160 A, Isc= 36kA for 1 sec

250 A, Isc= 36kA for 1 sec

315 A, Isc= 36kA for 1 sec

400 A, Isc= 36kA for 1 sec

Supplying, installation, testing & commisioning of following Tap off Box Plug in type for bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with all necessary accessories complete.

PLUG-IN BOX suitable for 32A to 125A MCCB

PLUG-IN BOX suitable for 160A MCCB

PLUG-IN BOX suitable for 200A to 400A MCCB

Supplying, installing on wall or suspension on ceiling, testing and commissioning of following capacity Air Insulated Compact Type Copper Rising Main for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 3P4W+PE , necessary joints, elbow joints & expansion joints, fire barrier at each floor, continuous earthing with 2 Nos Copper strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. 250 A, Isc= 36kA for 1 sec

Supplying, erecting, testing and commissioning of Flange end as per design requirement & site condition suitable for Copper , 3 phase 4 wire 415V, 50 Hz A.C, 15kA short circuit rating for 0.1 sec, for Air Insulated type BBT with necessary accessories complete conforming to IEC 61439-6. 250 A, Isc= 36kA for 1 sec

Supplying, erecting and commissioning Vertical or Horizontal 90 Degree/Tee Elbow with Spring Hanger & Horizontal Bracket for Air Insulated type Copper bus trunking/ rising mains of capacity, 3 Phase 4 wire 415V, 50Hz AC supply, 15kA short circuit rating for 1 sec made galvanized sheet metal enclosure duly powder coated with all necessary accessories complete conforming to IEC 61439-6. 250 A, Isc= 36kA for 1 sec

Supplying, installation, testing & commisioning of following capacity End Cover for Air Insulated Type Copper bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with all necessary accessories complete. 250 A, Isc= 36kA for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug Outlet Cover for Air Insulated Type Copper bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with all necessary accessories complete. 250 A, Isc= 36kA for 1 sec

SUBHEAD - XXV - UPS WIRING

Supply, installation, testing and commissioning of 160kVA Modular UPS 250kVA Frame 7X 25kVA power modules SNMP card 12V SMF Battery for 30 mins back-up @0.8pf 120AH x 50x 2 batteries 12m DC cable ,battery rack and related accessories as per specification and confirm to IEC 62040-3

Supply, installation, testing and commissioning of 40kVA Modular UPS Trimode HE 6.7X 6 power modules SNMP card 12V SMF Battery for 30 mins back- up @0.8pf 150AH x20 nos 7m DC cable ,battery raEk and related accessories as per specification and confirm to IEC 62040-3

Supply, installation, testing and commissioning of 30kVA Modular UPSTrimode HE 30kVA Frame 5kVA X 6 nos power modules SNMP card 12V SMF Battery for 30 mins back- up @0.8pf 120AH x 20 nos 7m DC cable ,battery rack and related accessories as per specification and confirm to IEC 62040-3

Supply, installation, testing and commissioning of 10kVA Trimode HE 20 kVA Frame 3.4kVA X 3 power modules SNMP card 12V SMF Battery for 30 mins back- up @0.8pf 42AH x20nos 7m DC cable ,battery rack and related accessories as per specification and confirm to IEC 62040-3

Supply, installation, testing and commissioning of 20kVAHPi33 EVO SNMP card 12V SMF Battery for 30 mins back- up @0.8pf 75AH x20nos 7m DC cable ,battery rack and related accessories as per specification and confirm to IEC 62040-3

Supply, installation, testing and commissioning of 7.5kVA Premius R UPS, 3 Phase input & 1Phase output Input Power factor > 0.8, efficiency SNMP Card 12V SMF Battery for 30 mins back- up @0.8pf 18AH x24nos 7m DC cable ,battery rack and related accessories as per specification and confirm to IEC 62040-3

SUBHEAD - XXVI - DG SET

Supply, erection, testing and commissioning of 415V, 3phase 50HZ, 4 wire Radiator cooled 1250 KVA DG Sets with approved acoustics enclosure outdoor type and control panel inside the enclosure. The Diesel Engine shall be complete with necessary control and safety devices as per latest IS/ BS specifications. The Engine shall be suitable for continuous operation of Generator (Prime Genset), inclusive of flywheel, flexible coupling, air cleaner, corrosion resistor, radiator, fan with guard, fuel pump, fuel filter, electronic governor, starting system with separate Battery charger with 2nos 24V sealed low maintenance batteries, voltage regulator, Instrument panel with RPM Indicator, exhaust silencer (residential), protections against low lub., oil pressure, high water temperature and with standard capacity fuel tank (750-900Ltrs.) inside the enclosure with all piping connections, diesel feed pump, necessary fuel piping arrangement from external fuel tanks to DG set, battery stand, anti vibration pads and first filling of lubricating oil and fuel oil for gen set including top up fuel tank.

The Alternator shall be suitable for 415V 3phase, 4wire, 50Hz AC supply operation and shall be able to deliver full load. Load testing at site and factory shall be carried out. 2 hours load testing at factory and 2 hours load testing at site. Contractor shall arrange load bank at site for testing. The rate is included for carry out necessary factory inspection and commissioning at site in the presence of authorised representative of manufacturer.

Supply, erection, testing and commissioning of 415V, 3phase 50HZ, 4 wire Radiator cooled 500 KVA DG Sets with approved acoustics enclosure outdoor type and control panel inside the enclosure. The Diesel Engine shall be complete with necessary control and safety devices as per latest IS/ BS specifications. The Engine shall be suitable for continuous operation of Generator (Prime Genset), inclusive of flywheel, flexible coupling, air cleaner, corrosion resistor, radiator, fan with guard, fuel pump, fuel filter, electronic governor, starting system with separate Battery charger with 2nos 24V sealed low maintenance batteries, voltage regulator, Instrument panel with RPM Indicator, exhaust silencer (residential), protections against low lub., oil pressure, high water temperature and with standard capacity fuel tank (750-900Ltrs.) inside the enclosure with all piping connections, diesel feed pump, necessary fuel piping arrangement from external fuel tanks to DG set, battery stand, anti vibration pads and first filling of lubricating oil and fuel oil for gen set including top up fuel tank.

The Alternator shall be suitable for 415V 3phase, 4wire, 50Hz AC supply operation and shall be able to deliver full load. Load testing at site and factory shall be carried out. 2 hours load testing at factory and 2 hours load testing at site. Contractor shall arrange load bank at site for testing. The rate is included for carry out necessary factory inspection and commissioning at site in the presence of authorised representative of manufacturer.

SUBHEAD - XXVII- EARTHING

Supply & Erecting of maintenance free Earth station (pipe in pipe type) with consisting of :

50mm dia, 3 Mtr length G. I. electrode capsule with 250 micron copper bonded on electrode, filled with earth enhancing compound, sealed at both ends and brazed lead for connection at one end, suitable for direct installation at site, at a depth of 3.0 Mtrs. Earth Enhanced compound (40 KG), Soil Conditioning Gel & Moisture Retaining Compound (5 KG) upto a depth of 3.0 Meters around the electrode capsule. FRP round inspection chamber/ housing with cover 275mm (top) X 310mm (base) X 250mm (height)

80mm dia, 3 Mtr length G. I. electrode capsule, filled with earth enhancing compound, sealed at both ends and brazed lead for connection at one end, suitable for direct installation at site, at a depth of 3 Mtrs. Earth Enhanced compound (40 KG), Soil Conditioning Gel & Moisture Retaining Compound (5 KG) upto a depth of 3.0 Meters around the electrode capsule. FRP round inspection chamber/ housing with cover 275mm (top) X 310mm (base) X 250mm (height)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.

Supply and laying of following size earth strips at 0.5 Mtr below ground including excavation and refilling of earth when laid in ground and with all fixing accessories when laid in trench with including connection/ terminating to Earth Station with G.I. nut, bolt, spring, washer, bi-metallic strip, exothermic welding etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 Meter below ground as strip earth electrode, including connection/ terminating with G.I. nut, bol, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supply & Erecting of 50 X 5mm hot dip GI strip laid in ground with standard mounting accessories.

Supply and laying of following size earth strips at 0.5 Mtr below ground including excavation and refilling of earth when laid in ground and with all fixing accessories when laid in trench with including connection/ terminating to Earth Station with brass nut, bolt, spring, washer, bi-metallic strip, exothermic welding etc. as required.

a) 4 sq. mm Copper wire

b) 8 SWG Copper wire

Supplying and erecting GI wire of high purity of required sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/conduit with screws complete.

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with insulating and non-corrosive bond with required joints

SUBHEAD - XXVIII - LIGHTNING PROTECTION

Supply, installation, testing & commissioning of 8 mm aluminium round conductor complete as specified in drawing & meets the requirements of DIN EN 50164- 2 (VDE 0185 part 202) & VDE 0185-305 (IS/IEC 62305)

Supply, installation, testing & commissioning of roof conductor holder for parapet - polyamide conductor holder: with M8 female thread or diameter 7mm, M8 screw to connect the conductor holder, weather & temperature resistant from -35 to +90 deg C tested. conductor holder @1metre distance.

Supply, installation, testing & commissioning of polyamide roof cable holder for flat roof: DIN 48829 formB1, closed from bottom filling weight 1kg (frost resistant concrete) sleeves from polyethylene black @ 1metre distance

Supply, installation, testing & commissioning of vertical air terminal with accessories, providing air terminals as per IS - IEC 62305 part 3 16mm rod tapered to 10mm aluminium rod. Meets the technical specifications according to DIN EN 50164-2 (VDE 0815 part 202), meets the requirement of VDE0185/305 (IS/IEC 62305) 3mtr air terminal: semi hard (E-AIMgSIO5 corresponds to DIN 48801 suitable for high wind load.

Supply, installation, testing & commissioning of cross universal connector, for T & cross connection to route vertical down conductor / mesh formation made of hot dipped galvanised iron with necessary screws etc as required installation with 4 hexagonal bolts M8*25 with M8 hexagonal nuts.

Supply, installation, testing & commissioning of expansion piece with connector for equalising temperature related length changes. Necessary on conductors length over 20mtr. For round conductor Rd 8/ALU OBO type 172 AR 5218 92 6

Supply, installation, testing & commissioning of connector for T cross & parallel connectors. Quick installation using hexagonal bolts M10X30 high grade hot dip galvanised conforms to the requirement according to DIN VDE 0185-305 (IS-IEC 62305) (2No / expansion piece)

Supply, installation, testing & commissioning of test joint folding clamp suitable to connect 8mm round conductor & max by 30X3 mm GI strip as specified in the drawing & directed by engineer

Supply, installation, testing & commissioning of lightning counter - to count no of lightning strike & it can record the date & time of lightning incident also tested as per IEC 62561-6

SUBHEAD - XXIX - EXTERNAL POWER SUPPLY

TRANSFORMER Supply, installation, testing and commissioning of 22kV/433V, 1000kVA capacity hermetically sealed corrugated tank based oil cooled ONAN copper wound Distribution Transformer with On Load Tap Changer (OLTC)(+5% to -15%), RTCC Panel, AVR, outdoor with enclosed termination box at primary side and secondary side, Alarm & trip contact for Oil, Winding, Gas & Pressure, control wiring up to 22KV HT switch gear panel for trip and alarm circuit, with first filling of mineral power oil and including excavation in all kind of soil SDR, required RCC foundation, oil sample valve etc. The rates is included for carry out necessary factory inspection and commissioning at site in the presence of authorised representative of manufacturer. Transformer losses as per latest IS : 1180 Energy Efficiency Level 2.

SUBSTATION ACCESSORIES

a) Supply and laying of 16mm thick 22KV, grade Rubber Mats of size1000mm x2000mm

b) Supply and laying of 16mm thick 433V, grade Rubber Mats of size1000mm x2000mm

c) Supply and fixing of CO2 Fire Extinguishers 4.5Kg capacity

d) Supply and fixing of 4nos Fire Buckets with stand

e) Supply and fixing of Laminated First Aid Charts in Hindi , English language

f) Supply and Fixing of Laminated SLD-A1size

g) Supply of Hand Gloves

h) Supply of First Aid Box

i) Supply of Danger Notice Board in Two/Three languages

Supply, fabrication, erection of MS structural members such as 50x50x6 mm angle, flat strip, C channel including all fixing accessories or U channels for installation of HT/LT panels/ cable trays in trench and painting of the tray with 2 coats of Red Oxide Primer and 2 coats of Synthetic enamel paint complete as required.

HT CABLES Supplying , erecting & terminating Aluminium HT Cables, 22 kV(UE), 3 x 150 sq. mm. aluminium conductor Stranded Compacted Circular Aluminium Conductor, Conductor Screen with Extruded Semi Conducting Compound, XLPE Insulated, Insulation Screening with Extruded Semi Conducting Compound in Combination with Copper Tape, AL Round Wire Armoured, and Overall PVC Sheathed Cable Conforming to IS 7098 (Part- 2) 2011 with upto Date Amendments.

Supplying , erecting & terminating Aluminium HT Cables, 22 kV(UE), 3 x 185 sq. mm. aluminium conductor Stranded Compacted Circular Aluminium Conductor, Conductor Screen with Extruded Semi Conducting Compound, XLPE Insulated, Insulation Screening with Extruded Semi Conducting Compound in Combination with Copper Tape, AL Round Wire Armoured, and Overall PVC Sheathed Cable Conforming to IS 7098 (Part- 2) 2011 with upto Date Amendments.

Providing and erecting Heat shrinkable indoor termination kit for 11 kV (UE)/ 22 kV ( E ) XLPE HT cable 3x120 to 185 sq. mm. with necessary material

Providing and erecting Heat shrinkable outdoor termination kit for 11 kV (UE)/ 22 kV ( E ) XLPE HT cable 3x120 to 185 sq. mm. with necessary material

Providing and erecting Heat shrinkable straight through joint kit for 11 kV (UE)/22 kV ( E ) XLPE HT cable 3x120 to 185 sq. mm. with necessary material

MV Cables Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½core 240 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 3½ core 185 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 3½ core 150 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 3½ core 70 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per as per IS 3961 specification.Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 3½ core 50 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per as per IS 3961 specification.Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 3½ core 35 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 4 core 25 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per as per IS 3961 specification.Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Supplying, erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) multistranded cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per IS 3961 specification. Including sand cushioning, brick protection & sand filling as directed by Engineer In Charge.

Providing & erecting epoxy straight through joint outdoor/ indoor for LT XLPE armoured cable 300 sq mm., with necessary material as per specification

Providing & erecting epoxy straight through joint outdoor/ indoor for LT XLPE armoured cable 240 sq.mm., with necessary material as per specification

Providing & erecting epoxy straight through joint outdoor/ indoor for LT XLPE armoured cable 120 to 185 sq. mm., with necessary material as per specification

Providing & erecting epoxy straight through joint outdoor/ indoor for LT XLPE armoured cable 70 to 95 sq mm., with necessary material as per specification

Providing & erecting epoxy outdoor / indoor end termination kit for LT XLPE armoured cable 240 to 300 sq mm., with necessary material as per specification

Providing & erecting epoxy outdoor / indoor end termination kit for LT XLPE armoured cable 70 to 120 sq mm., with necessary material as per specification

Providing & erecting epoxy outdoor / indoor end termination kit for LT XLPE armoured cable 25 to 50 sq mm., with necessary material as per specification

Providing & erecting epoxy outdoor / indoor end termination kit for LT XLPE armoured cable 2.5 to 16 sq mm., with necessary material as per specification

Supplying, installing, testing and commissioning of 25 kWp ON-GRID Solar pV System / Plant consisting Solar PV Poly Crystalline Panel (585 Wp X 171 Nos.) and Solar ON-GRID Inverter of similar capacity (THD<3%) with interconnecting wires / cables up to solar ON GRID inverter, proper base plate, canopy box to house Inverter and necessary accessories i.e. ACDB/ DCDB , MCB etc. wiring up to solar Inverter in casing and capping, display board, sign board, two distinct earthing, lightning arrester, liasoning charges, remote monitoring system with maintaining card / chip for 5 years including net charges for RMS System, complete upto net meter Installation and export to the grid with 5 year ON-SITE warranty and fully comprehensive maintenance contract as per Specification. as per IEC 61215 latest Edition or IEEE 1262

Supply and laying of following dia. RCC hume pipes with collars for road crossings, laid 750mm below ground level including excavation in all kind of soil, SDR, refilling of earth after hume pipes are laid and other civil engineering works. a) 300mm dia.

Constructing masonry Chamber 90 x 90 x 90 cm, inside with 75 class designation work in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve, with C.I. space box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1 : 3 (1 cement " 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design:

Providing & Laying G.I Class C Pipe 150mm dia.

Supplying, installing, CCS-2 DC FAST EV CHARGER 30 KW (200-1000V DC) Input Voltage(AC) : 3 Phase, 415 Vac(374~440Vac) Input Frequency : 50±1Hz Wire Connections : 5 (L1,L2,L3,N,PE) Number of Outputs: 1 Nos. Output Connector : 30 kW CCS-2 Output Rating: 30kW Display: 7" TFT LCD with touch User Authentication: RFID Based Charger and CMS: Protocol: OCPP 1.6 (Open Charge Point Protocol) Interface: Ethernet/4G/WiFi Wire Length: 5m Ambient Temperature: -20⁰C to 55⁰C Storage Temperature: -20⁰C to 70⁰C Altitude: <2000Mtr Humidity: <95%, Non-Condensing Ingress Protection: IP54 Cooling: Forced Fan Air Mounting : Wall Mounted Size (WxDxH) : 530 x 200 x 752 mm With Hydro Carbon Sensor with required accessories shall conforms to IS 17017

HT PANEL Supply, erection testing and commissioning of Five breaker panel board totally enclosed sheet steel clad floor mounting, vermin proof, fully interlocked horizontal isolation, extensible, horizontal draw out, air insulated, metal clad switchboard having single / double isolation features complete with circuits as detailed below. The switchboard shall be complete with necessary PVC insulated copper busbars, small wiring, labels, cable eyes, cable termination to receive XLPE cables, foundation bolts and suitable for operation on 22kv 3 phase, 50 cycle, earthed system with a rupturing capacity of 1000 KVA at 22kv as per specification.

2No. Triple pole Microprocessor IDMT overcurrent & earth fault relay with two outer elements connected for overcurrent protection and the middle element for earth fault protection overcurrent setting 50% - 200% Earth fault setting 20% - 80% (51 and 51N). 2 No. circuit breaker control switch for electrical (T/N/C). 1No. Master trip relay (86) 2No. Trip circuit supervision relay (95) 2set of Red/Green indicating lamps for close and open position. 2 No. Amber indicating lamp for auto trip. 2 No. clear indicating lamp for trip circuit healthy. 2set of white indicating lamps one per phase. 2 No. blue indicating lamp for spring charged.1 No. clear indicating lamp for trip circuit healthy.1set of white indicating lamps one per phase. 2 No. blue indicating lamp for spring charged. 2 No. Push button on front door for emergency trip. 2 hooter of 230volt with NO-NC contactor for 24 volt DC No. cable termination BOX to receive 22kv XLPE cable 3 core 185sq mm. 1 No. hooter. 1set of ferrules, fuses, limit switch and wiring as required. BUSCOUPLER ( ONE NOS 1No. Air insulated metal clad housing. 1set of 3 phase PVC insulated copper busbars 630 Amp rating. 6 Nos. single pole cluster type Isolating contacts i.e. plug and switches.

1No. Triple pole draw out truck mounted 1 MVA, 630 Amp, 22000volts Vacuum Circuit Breaker. INo. Trip free motor spring charged closing mechanism complete with necessary auxiliary switches, emergency hand trip device and mechanical 'OFF' & 'ON' indicator. 1No. 24 volt DC shunt trip coil. 1No. 24 volt DC closing coil. 1 No. 230 volt AC Spring Charging Motor/Motor wound spring operated mechanism OUTGOINGS ( TWO NOS FOR TRANSFORMER 2No. Air insulated metal clad housing. 2set of 3 phase PVC insulated copper busbars 630 Amp rating. 6 Nos. single pole cluster type Isolating contacts i.e. plug and switches. 2No. Triple pole draw out truck mounted 1 MVA, 630 Amp, 22000volts Vacuum Circuit Breaker. INo. Trip free motor spring charged closing mechanism complete with necessary auxiliary switches, emergency hand trip device and mechanical 'OFF' & 'ON' indicator. 2No. 24 volt DC shunt trip coil. 1No. 24 volt DC closing coil. 2 No. 230 volt AC Spring Charging Motor/Motor wound spring operated mechanism 6 Nos. Cast resin Current transformers of ratio 30A/5, 15VA burden Class 5P10 for protection & class 1.0 for metering. 1 Set of Strip heater to prevent

2No. Triple pole Microprocessor I.D.M.T. overcurrent and earth fault relay, with two outer elements connected for overcurrent and the middle element for earth fault protection overcurrent setting 50% - 200% Earth fault setting 20% -80% and with instantaneous element on all 3 pole settings 500-2000% on overcurrent and 200-3200% on earth fault (51, 51N, 50 and 50N) 2 No. circuit breaker control switch for electrical (T/N/C). 2 set of fuses, limit switches wiring etc. as required. 2No. Master trip relay (86).1No. Trip circuit supervision relay(95). 2 hooter of 230volt with NO-NC contactor for 24 volt DC 2No. cable termination box to receive 22kv XLPE cable 3 core 185 sq mm. The switchboard shall be complete with earth bus, all interconnections, labels wiring, etc as required. .

SUB HEAD XXX: EXTERNAL LIGHTING

Supplying and erecting 100W, LED Up/Downlighter type wall mounted light fitting with beam angle 15 Deg RGBW / WW illlumination power coated steel sheet formed and fabricated main body, finished with pure polyester powder coated graphite grey, (IP-66) protection, lumens output of the luminaire : not less than100 Lumens per Watt, with all fixing accessories

Supplying and erecting 85W, LED Up/Downlighter type wall mounted light fitting with beam angle 15 Deg RGBW / WW illlumination power coated steel sheet formed and fabricated main body, finished with pure polyester powder coated graphite grey, (IP-66) protection, lumens output of the luminaire : not less than100 Lumens per Watt, with all fixing accessories

Supplying and erecting 36W, LED Up/Downlighter type wall mounted light fitting with beam angle 15 Deg RGBW / WW illlumination power coated steel sheet formed and fabricated main body, finished with pure polyester powder coated graphite grey, (IP-66) protection, lumens output of the luminaire : not less than100 Lumens per Watt, with all fixing accessories

Supplying and erecting 54W, LED Up/Downlighter type wall mounted light fitting with beam angle 15 Deg RGBW / WW illlumination power coated steel sheet formed and fabricated main body, finished with pure polyester powder coated graphite grey, (IP-66) protection, lumens output of the luminaire : not less than100 Lumens per Watt, with all fixing accessories

Supplying and erecting 24W, LED wall washer light fitting with beam angle 10x30 Deg RGBW / WW illlumination power coated steel sheet formed and fabricated main body, finished with pure polyester powder coated graphite grey, (IP-66) protection, lumens output of the luminaire : not less than100 Lumens per Watt, with all fixing accessories

Supplying and erecting DMX Splitter/Amplifier with all fixing accessories

Supplying and erecting DMX MASTER CONTROLLER (U 11) with all fixing accessories

Supplying and erecting DMX Cable with all fixing accessories

Supplying and erecting 7-9W integrated LED Bollard Graphite grey powder coated GI Pipe housing. Mushroom shape opal acrylic diffuser is fixed in die-cast aluminium base for pleasant light output LEDs mounted on die-cast aluminium base.Degree of protection: IP65 Hrs. at L50B50, including driver complete

Supplying and erecting 25W streetlight Epoxy powder coated pressure die-cast aluminium housing. Side entry mounting for max. 40mm OD pipe bracket.Luminaire efficacy* 120 lm/W Luminous flux** 3000lm Color Rendering Index >70 Built-in Surge protection 4kV Ingress Protection IP66 & Impact Protection IK08

Supplying and erecting Decorative garden Lighting Pole of 4.50 Mtr. high (above ground) including 45W LED Post Top Latern Light fitting Spun aluminum powder coated housing with PDC heat sink.PMMA opal & clear diffuser Suitable for Ø60mm OD pole. Luminous flux ± 10% 3150 lm Correlated Color Temperature 3000K ±175K THD <10% Built-in Surge protection 4 kV External Surge protection 10kV Ingress Protection IP65 Mechanical impact protection IK06

Supplying and erecting Decorative garden Lighting Pole of 3 Mtr. high (above ground) including 40W LED Post Top Latern Light fittingSpun aluminium graphite grey, powder coatedCast aluminium spigot housing.Polycarbonate opal diffuser.Luminous flux** 3200 lmCorrelated Color Temperature 5700KTHD <10%Built-in Surge protection 4 kVExternal Surge protection 10kVIngress Protection IP65Mechanical impact protection IK06

Supplying and erecting hot dip GI octagonal street light pole of 8 Mtr. Long, bottom dia – 130mm, top dia – 70mm, hot dip galvanized 80-100 microns, thickness 3 mm, 300x300x12mm GI base plate, J type foundation nut-bolts, earthing studs/terminals, 1.5 Mtr out reach double arm bracket, built-in control box with service door including lock and safety chain consisting suitable connector for termination of 3.5C- 35 sq. mm aluminium cable (2 terminations : 1 Incoming and 1 Outgoing) including necessary fixing arrangement, the control gear tray is prewired with suitable rating of MCB, terminal connectors for loop-in loop-out arrangement, 2nos 40mm dia HDPE Pipes of 1.5mtr. Long for incoming and outgoing cables, including earthing arrangement, excavation & back filling, bedding, PCC foundations 1:2:4, coping, PCC Pedestal complete as required.. The wiring from Junction box to Light fixture shall be carried out with 3core 2.5sq.mm multistranded copper conductor cable. Installation: Surface mounted with GI base plate and fitted on a pre-formed foundation.

Supplying and erecting 45W streetlight Epoxy powder coated pressure die-cast aluminium housing.Side entry mounting for max. 40mm OD pipe bracket.Luminaire efficacy* 120 lm/W Luminous flux** 5400lm Color Rendering Index >70 Built-in Surge protection 4kV Ingress Protection IP66 & Impact Protection IK08

Supplying and erecting 20 Mtr. High Mast, Thickness : Top 3 mm, Bottom 4 mm, diameter : Top 150 mm, Bottom 460 mm, Light Fittings : 12 Nos. 350W LED flood light fittings, Suitable for 180 KMPH wind speed, Non Flame Proof Motor, Movable lantern carriage, Lighting Arrestor, Double drum Winch, 6 mm 316 Grade SS hoisting ropes of 7/19 construction, trailing copper cable - 1 per mast 5 core 6 sq. mm, Lighting Finial, Anchor plate & Template, Foundation bolts & nuts, 12W LED twin aviation lights shall be control thru' independent circuit/ cable and MCB, feeder pillar including earthing arrangement, control panel with digital programmable timer switch, excavation & back filling, bedding, RCC M30 foundations , coping, complete as required.

Supplying and erecting Decorative Wall Lantern & Post Top Lights Decorative garden 12-15W LED Post Top Latern Light fitting Spun aluminum powder coated housing with PDC heat sink.PMMA opal & clear diffuser Suitable for Ø60mm OD pole. Luminous flux ± 10% 3150 lm Correlated Color Temperature 3000K ±175K THD <10% Built-in Surge protection 4 kV External Surge protection 10kV Ingress Protection IP65 Mechanical impact protection IK06

Supply & instalaltion of Spike Light 7-10W LED Garden Light 450lm LED Lumens, Dimension 90x1506mm, Made up of Extruded Al Tube, Pure Polyster Powder Coated finish, Non Yellowing UV Stabilized Clear Acrylic Rod, Mounting Spike Arrangement, Non Integral Constant Current Power Supply 24v, IP67 1.25Amps 30w, Operating Voltage Range 100-270v AC., Operating Temp. - 15degree C. to +50 Degree C., CRI>80, CCT 2700K/ 3000K, Life L70 60000hrs., SDCM<3, Power Factor> 0.9, THD <15%, Surge Protection 1kV, Efficiency >75%, Syymetrical Light Distribution, IP65, CE and BIS Marked

Supply, installation, testing and commissioning of following rating FLP socket / switch Fuse units in FLP enclosure and plug top on angel iron frame work & other MS support structure complete with all fixing accessories, hardware etc. complete as required The FLP Sockets / SFUs shall be confirming to IP-65.

20A DP+E, Single Phase 250V Grade FLP Plug Top & Socket with 20A DP MCB control

FLP 4 way Junction box of size 125 dia x 100 mm depth suitable for 3/4" dia cable entries

SUB HEAD XXXI : DIGITAL PUBLIC ADDRESS SYSTEM

Supply, installation, testing and commissioning of Digital Public Address Systemomplying to International standards of Emergency Sound & Back Ground Music System complete with all necessary accessories/ hardware with following equipment/ wiring/ items. outdoor equipments should have corrosion resistance coating.

Design, supply, installation, testing and commissioning of Windows based Central Monitoring & Control Software with 8 Licenses and expandable to 32, shall be capable to perform paging and message playing to all zones of devices over LAN. Unicast/multicast, Routing, Message Playing, Scheduler, Text to speech and volume control, shall be capable to monitor all the system components, Monitoring device status such as Offline/online or line-occupied/line available to Support TCP, UDP, SIP, RTP and IGMP protocol. The Server shall have user friendly to configuration and flexibility in button design. inclusive of required software & license.

Supply, installation, testing and commissioning of Intel Core i5 Quad Core @ 3.3 GHz or Latest, 16GB dual channel DDR3 1333/1600,Graphics NVIDIA (2 GB dedicated) With DVI/HMI output with 2TB 7.5K rpm SATA hard disk, PS/2 / USB Compatible, Dual Gigabit Ethernet, power supply provisions Cost should be With Life time license for Windows 8 enterprise/professional or latest software compatible MacAfee /Symantec Anti virus, with 24 Inch LED Display Monitor & All other related software such MS office with liscesenced. The required operation & PA software etc. & Workstation should be FCC & UL listed.

Supply, installation, testing and commissioning of Digital Public Address and Emergency Sound System Controller complying to International standards of Emergency Sound System with inbuilt features like Completely digital audio and control data transmission, A built in message manager shall be able to store up to 100 emergency, total storage time up to 60 minutes, Min. 12 Zone Output with LED Indications. Min. Event Scheduler, Relay output and Gain adjustment in the in & output. inclusive of required software, license, associates cables & accessories.

Supply, installation, testing and commissioning of The system Router shall be an EN54-16/ UL certified device in a 1/2 RU, 19”cabinet. The device shall extend the number of zones in a system and shall contain all the necessary controlling and monitoring functions. The internal supervision system shall monitor the functions and operation of both itself and the connected devices & support to Min. 24 Zones. inclusive of required software, license, associates cables & accessories.

Design, supply, installation, testing and commissioning of IP Based Digital PA Processor /Encoder/ Decoder with fully Digital Audio system Encoder with Balanced Independed Audio Line Outputs, relay port, Ethernet Interface. inclusive of required license, software, associate cables, Power adapter & mounting accessories.

Design, supply, installation, testing and commissioning of 80W Single channel class D Amplifier with following features:- Short-circuit protection, thermal protection. inclusive of required license, software, associate cables, Power adapter & mounting accessories as completed.

Design, supply, installation, testing and commissioning of The Digital 2x 500W Class D, high efficiency amplifier shall be an EN54-16/UL compliant and certified system device in a 2 RU, 19”cabinet with following features:- Short-circuit protection, thermal protection. inclusive of required license, software, associate cables, Power adapter & mounting accessories as completed.

Design, supply, installation, testing and commissioning of The Digital 1x 500W Class D, high efficiency amplifier shall be an EN54-16/UL compliant and certified system device in a 2 RU, 19”cabinet with following features:- Short-circuit protection, thermal protection. inclusive of required license, software, associate cables, Power adapter & mounting accessories as completed.

Supply and installation, testing & Commissioning of 6W wall mount Indoor speaker with excellent speech & music reproduction with Effective frequency range(-10 dB) : 75 Hz to 18KHz, SPL at rated power (1Khz at 1 m) 96 dB with required mounting accessories & Hardware as completed.

Supply and installation, testing & Commissioning of 6W Ceiling mount Indoor speaker with excellent speech & music reproduction with Effective frequency range: 85 Hz to 20KHz6W, SPL at rated power (1Khz at 1 m) 90 dB with required mounting accessories & Hardware as completed.

Supply, installation, Testing & Commissioning of 25 W high‑efficiency ABS horn loudspeaker with weather protection IP65, Max. Power: 37.5 W,Rated Power: 25 Watts, Power tapping: 25 / 12.5 / 6.25 W, Effective frequency range(-10 dB) :(500 Hz to 5KHz), SPL at rated power (1Khz) 121 dB. inclusive of required associate cables & mounting accessories as completed.

Supply, installation, Testing & Commissioning of 50 W high‑efficiency ABS horn loudspeaker with weather protection IP65, Max. Power: 75W,Rated Power: 50 Watts, Power tapping: 50 / 25/ 12.5 / W. Effective frequency range(-10 dB) :(500 Hz to 5KHz), SPL at rated power (1Khz) 121 dB. inclusive of required associate cables & mounting accessories as completed.

Supply, installation, Testing & Commissioning of 15W ceiling mount speaker with excellent speech & music reproduction, Max Power: 20W, Rated Power: 15 Watts, Power Tapping: 15 W –10 W – 3.75W, SPL at rated power (1Khz at 1 m) 104 dB, Effective frequency range (-10 dB) : 100 Hz to 20 kHz, IP 63 inclusive of required associate cables & mounting accessories as completed.

Supply, installation, Testing & Commissioning of 15W Outdoor Projection peaker with excellent speech & music reproduction, Max Power: 15W, Rated Power: 10 Watts, Power Tapping: 10 W – 5 W – 2.5 W, SPL at rated power (1Khz at 1 m) 102 dB, Effective frequency range (-10 dB) 140 Hz to13 kHz, IP 63 inclusive of required associate cables & mounting accessories as completed.

Supply, Installation, Testing & Commissioning of modular type 36W volume control units with override mechanism suitable including front plate and anodised GI box in concealed manner of adequate sizes, including all fixing accessories.

Supply & fixing of Relay contact with standard connectivity accessories & hardware

Supply & fixing of warning light with relay contactor

Supply and wiring of 2C - 1.5 sq. mm. FRLS insulated multistranded copper conductor armoured cable in existing PVC/ GI conduit or direct on ceiling surface with clamp, complete as required.

Supply and wiring of 4C - 1.5 sq. mm. FRLS insulated multistranded copper conductor armoured cable in existing PVC/ GI conduit or direct on ceiling surface with clamp, complete as required.

SUB HEAD XXXII : ACCESS CONTROL SYSTEM

Supply, Installation , testing and commissioning of robust, versatile & Compact size of Fingureprint Scan Reader and Multi format (smart +proximity) card readers with multispectral imaging technology that captures fingerprint images from both the surface and the sub-surfac & Card read range of 4 inches. standard mounting accessories and hardware shall be incluided.

Supply, Installation , testing and commissioning of Smart Cards 16k with the possibility of printing the company details on its facia using dye sublimation method .

Supply, Installation, Testing, Commissioning of IP Based Two Door Controller along with all the necessary mounting accessories, software, license & hardware.

Supply, Installation, Testing, Commissioning of IP Based Single Door Controller along with all the necessary mounting accessories, software, license & hardware.

Supply, Installation, Testing, Commissioning of IP based Reader cum Controller (for Lifts) along with all the necessary mounting accessories.

Supply, installation, Testing & Commissioning Biometric Scan Reader, Card Reader and Keypad , Ethenernet port, built-in battery backup provides approx 4 hours continuous operation,built-in wireless Wi-Fi or GPRS for wireless communication, seamless integration with third party parol system & Adhar System standard required accessories & software should be incluided

Supply, Installation, testing & Commissioning of workstation PC core i5 processor or better along with 18" TFT/LCD Monitor, Mouse, Keyboard, enterprise OS License & Antivirus with 5 year Subscriptions including required accessories as per specification.

Supply and installation of Access Control Software support to 250000 Cards with Report generation GUI and time attendence feature & interface with HRMS & Interface with BMS with license.

Supply, Installation, testing and commissioning of robust, versatile & Compact size of Guest Room Locks with compatible with Multi format card readers , Lock should be elegant, Minimalistic and Modern Design, Rugged Stainless Steel Finish Body, wireless Technology support, minimum Battery capacity for 40000 Opening, compatible existing HID Seos Technology. standard mounting accessories and hardware shall be incluided.all standard mouting Hardware and accessories as completed.

Supply and installation of Guest Room Card Software support to 50000 Cards with Report generation GUI and time attendence feature & interface with HRMS & Interface with BMS with license. Incluiding ( 4 license).

Supply, Installation, Testing, Commissioning of single leaf EML with builtin magnetic contact & buzzer along with all the necessary mounting accessories.

Supply, Installation, Testing, Commissioning of double leaf EML with builtin magnetic contact & buzzer along with all the necessary mounting accessories.

Supply and installation of Panic Bars with sounders with standard mouting accessories & hardware.

Supply and installation of Exit switch with standard mouting accessories & hardware.

Supply, Installation, Testing, Commissioning of Emergency break glass switch along with all the necessary mounting accessories.

Supply, Installation, Testing, Commissioning of Long Range Multi-Format Card Reader along with all the necessary mounting accessories.

Supply, Installation, Testing & Commissioning of USB Type Card writer Pad for issue Cards to guest . All required Standard software, hardware & Accessories should be incluided as complete.

Supply, Installation, Testing & Commissioing of Smart Card Printer

Supplying, Installing, Testing & Commissioning of Portable Card Programmer /Encoder/ Writer with required software, Patch cords & required accessories as completed.

Supply and laying of 8c x 0.825 Sq.mm FRLS Armoured cable.

Supply and laying of 2c x 1.0 Sq.mm FRLS Armoured cable.

Supply and laying of 4c x 1.0 Sq.mm FRLS Armoured cable.

SUB HEAD XXXIII : ID & VISITOR MANAGEMENT SYSTEM

Suply, installation, Testing & Commissioing of PC Workstation with Visitor Mangement Software. The software must support at least 100,000 visitor cards. This visitor management functionality must allow the enrolment of visitors into the database, capturing of images and import/export of visitor data. Incluiding OS, Antivirus, license with 5 years subscription, 18" Monitor, Keyboard, patchcord & Standard Accessories

Supply, Installation, Testing & Commissioing of Logitech HD Webcam C270 or heigher with standard Accessories, software, license, patchcord & Mouting Hardware as complete.

Supply, Installation, Testing & Commissioing of HP LaserJet 1020 Plus Printer or equivalent or higher with standard Accessories, software, license, patchcord & Mouting Hardware as complete.

Supply of blank smart cards

Supplying, Installing, Testing & Commissioning of Portable Card Programmer /Encoder/ Writer with required software, Patch cords & required accessories as completed.

SUB HEAD XXXIV : IP CCTV SYSTEM

Supply, installation, programming, testing and commissioning of IP based CCTV system complete with software, hardware, all require accessories/ materials/ items for full fill the system working, if any other items require for the system working, it shall be in contractor scope (no extra/non schedule items), the following items as required to complete the system. Contractor shall give complete presentation before procurement of any material. The system logic shall be worked out in consultation with client and hardware/ software shall be developed/ procured to suit the same. Refer Technical Specifications of CCTV and ELV Schematics. Contractor shall submit all the compliances mentioned in the Technical Specifications.

Supply, installation, testing & commissioning of PTZ camera with continues 360° pan for both outdoor with 30x optical zoom Four individual stream with full FPS and full resolution Object auto tracking(Person/Vehicle) . Min. 1080p @ 60fps (1920x1080) in H.264/H.265 and Motion JPEG, external power supply or PoE, Day & Night, IP66, vandal resistant, work with low or no ambient lighting , Video Analytics like motion detection, tempering, line crossing etc, 120dB WDR, The camera shall be mounted on existing street light pole with suitable angle/ pole arm and necessary mounting accessories for e.g. interconnecting cables,housing, hardware etc. and it shall be from same OEM. The camera shall have minimum 64 GB SD local storage card external/internal power line surge protection device and internal/external power line surge protection device. ONVIF Profiles S , G & T, FCC, CE, EN,UL & NDAA Certified as per Technical specification.

Supply, installation, testing & commissioning of outdoor-ready IP camera for day and night surveillance, IP66-rated, varifocal min. 4-10 mm with minimum four individual configurable stream with full FPS and full resolution, Remote optical zoom and focus. Automatic IR cut filter. Multiple, individually configurable H.265 and Motion JPEG streams; min 4 MP resolution at 30 fp or better . Sensitivity-0.07 lx(color), 0.05 lx(mono/night), 0.0 lx (IR)Video motion detection, active tampering alarm, I/O ports, micro SD/SDHC memory card slot for edge storage. night vision enable IR with up to 30 meters (98 feet). Integrated bracket for easy mounting on wall and ceiling. Power over Ethernet. Operating conditions -30 °C to 50 °C (-22 °F to 122 °F). The camera shall be mounted on existing street light pole with suitable angle and necessary mounting accessories for e.g. interconnecting cables, hardware, housing, sunshield etc. and it shall be from same OEM. The camera shall have minimum 64 GB SD local storage card external/internal power line surge protection device. ONVIF Profiles S , G & T, FCC, CE, UL & NDAA Certified as per Technical specification.

Supply, installation, testing & commissioning of Indoor dome type IP based 1/3" color auto iris varifocal lens ( 4-10mm AVF), Cmos cameras min 4 MP auto iris cameras (high resolutions cameras). camera should full resolution with full FPS min Four Stream. Camera should be support Day/ Nigh, Motion temper and audio detection. Classified object : Person/ Vehicle,. IR Range Minimum 30 Meter, E-PTZ Feature WDR Electronic shutter, While balance ,BLC, DC, IRIS Anti-Flicker, Vandal proof housing ( IEEE 802.3 class 3/ Wattage less than 1- Watt). Camera lense Camera lens should be fixed as per site location & current Viewing. Camera should be POE Enabled & should be NDAA, CE, EN,FCC & UL listed/Approved & also ONVIF S/G/T compliant as per Technical Specification.

Supply, installation, testing & commissioning of Controller, IP system keyboard with LED Display to control PTZ. It should be as per Technical Specification.

Supply, installation, testing and commissioning of (N:N Geographical Redundant) Central VMS Management Server along with ICCC Management server Software &, Video Analytics with N:N Geographical Redundancy to manage and control all the cameras from control room Software shall support minimum channel licenses with camera license & Manimum 100 cameras as mentioned below to be configured over dual Database Server to avoid downtime . Video Management software shall be able to get seamlessly integrated with other security Management Software systems like access control, Visitor Management,Gaurd tour, Duress alarm etc. Software shall support servers and network attached storage. Failure of main server shall not affect recording and live view. System shall give full redundancy and reliable solution. Software shall support third party analytics for future integration. Contractor shall size the Server for footage at real time 30 fps for viewing, 30 fps at least 60days of continuous recording and submit data sheet of their storage calculation for both MPEG 4 and H.264 recording formats dedicated As per specs system to be designed based on Server- Client architecture Minimum specification for Video Management. (Note: 1 Lot comprised of 2 Set - One for Security Control Room & One for Admin Building CCTV Room. required interactive panel and support server hardware to be incluided).

Supply, installation, testing and commissioning of server Hardware with minimum specification of Mount Intel® Xeon® processor/ equivalent / latest generation, 2 X 2 core 2.6Hz or higher CPUs, Support to at least 4 VM, Memory : 40 GB ECC DDR4 upgradable to 100 GB, Graphics NVIDIA (8 GB dedicated) With 2-DVI/HMI output with Dual Screen card & associate Software of operation, Internal Storage of 2TB 7.5K or higher rpm SATA hard disk along with Dual 10G-Gigabit Ethernet ports, PS/2 / USP Compatible, High –Efficiency, Hot-plug, redundant power supplied, hot-plug drives bays; dual internal SD support; hot-plug, redundant fan. Cost should be With Life time license for Operating System : Microsoft® Windows Server® 2008/2012 enterprise / professional or latest software, MacAfee /Symantec Anti virus & All other related software such MS office with liscesenced. software etc. as per specifications. Design to be shared by each vendor as per their architecture. Harddisk to be incluided. Vendor to submit Hard Disk calculation sheet for consultant/client approval. The software & Workstation should be FCC & UL listed. ( Server Hardware shall be as per OEM requirement) (Note: 1 Lot comprised of 2 Set - One for Security Control Room & One for Admin Building CCTV Room)

Supply Installation Testing & commissioning of Embeded Linux based ISCI ( Ip San ) having Minimum 1G Mbps Recording Bandwidth & 16 Hot-Swapable HDDs of 72 TB capacity, RAID 0 / 10 / 5 / 6, RAID5 + Hotstandby, Easy Configuration : One-Touch Setup of RAID Volume, Storage shall have Network Failover, Load Balancing support, support to MJPEG, H.264 & H.265. Setup via Webpage & Remote Storage Management S/W, 4 Gigabit Ethernet Ports, 3U chassis with Front Key-Lock, Dual SMPS for Redundancy. recording should be for 60 days.Harddisk to be incluided. Vendor to submit Hard Disk calculation sheet for consultant/client approval.

Supply, installation, testing and commissioning of Intel Core i5 Quad Core @ 3.3 GHz or Latest, 8GB dual channel DDR3 1333/1600,Graphics NVIDIA (2 GB dedicated) With 2-DVI/HMI output with Dual/Quad Screen card & associate Software of operation,, 2TB 7.5K rpm SATA hard disk, PS/2 Compatible, Dual Gigabit Ethernet, power supply provisions Cost should be With Life time license for Windows 8 enterprise/professional or latest software compatible MacAfee /Symantec Anti virus & All other related software such MS office with liscesenced. The required operation & CCTV remote software etc. & Workstation should be FCC & UL listed.

Supply, installation, testing and commissioning of Front Projection Video Wall Display of ( 2 X 2 cube Matrix ) 4 No. of Minimum size of 49-50" Diagonal Professional Large Format Video Wall display Panel with thin bezel, 500 nits brightness, 24/7 monitoring in control room, HDMI. LAN & control Ports. It shall come with remote control and data representation with all necessary Fixing accessories for viewing. Also required switch, Software & Modules and associate wall mounting Kit / Frame & required accessories to be considered. The Panel should be FCC & UL listed (maximum 16 Nos cameras in one screen viewing station)

Supply, installation, testing and commissioning of Main Viewing Screens for CCTV Monitoring Station with full HD professional display for 24/7 monitoring, display size shall not be less than 49-50"with HDMI, PC inputs. It shall come with remote control and shall have various picture mode options. for data representation with all necessary Fixing accessories for viewing. Also required switch, Software & Modules to be considered. The Monitor should be FCC & UL listed (maximum 32 Nos cameras in one screen viewing station)

Supply, installation, testing and commissioning of Viewing Screen for above mentioned work station with table mount full HD professional monitor, no less than 24" with HDMI , PC Inputs. It shall have various picture mode options. For data representation with all necessary fixing accessories for viewing The Monitor should be FCC & UL Listed (Maximum 32 on one viewing Station)

Supply, installation, testing and commissioning of 8 Port USB KVM Switch with required associated cables, Software, License & accessories as completed.

Supply, installation, testing and commissioning of Wireless Keyboard & mouse with associated Tx & Rx modules, required software and accessories as completed.

Supply, Laying of 15 Meter HDMI to HDMI Patch Cord.

Supply, Installation, testing & Commissioning of workstation PC core i5 processor or better along with 18" TFT/LCD Monitor, Mouse, Keyboard, enterprise OS License & Antivirus with 5 year Subscriptions including required accessories as per specification.

Supply, installation, Testing & commissioning of Digital/IP Based Video Door Phone/bell with Minimum Size of 1 Nos. 7 inch Colourful TFT Screen, video Resolution 1080P, wide angle Coverage, Built in Microphone and Lousespeaker, Eco cancellation, Water & dust Resistance and 1 X 1080P Camera with Bell. all required accessories with patch cord should be incluided.

Supply, installation, Testing & commissioning of Digital/ IP Based Video Door Phone/bell with Minimum Size of 2 Nos. 7 inch Colourful TFT Screen, video Resolution 1080P, wide angle Coverage, Built in Microphone and Lousespeaker, Eco cancellation, Water & dust Resistance and 1 No. X porch unit camera unit inbuilt camera and bell with additional camera. all required accessories with patch cord should be incluided.

SUB HEAD XXXV : BAGGAGE SCANNERS

Supply, fixing, Testing & Commissioning x-ray baggage sacnner with bi-direction scanning, baggage counting, LAN Port for remote Monitoring & Control with all required monitoring station ( incluiding min. 19" Monitor, CPU, Joystic etc as required ), Software, license, hardware & accessories. Require AERB certification by OEM for proposed Product.

Supply, Installation, Testing & Commissioning of Baggage scanner small: computer based multi energy X-Ray Baggage Inspection System mounted on castor wheels capable of passing through bags of dimensions 530 mm (W) X 330 mm (H) with 22”/24 LCD Monitor, Input / Output rollers with frames. incluiding Server , required Computer Hardware & UPS etc.

Supply, Installation, Testing & Commissioning of Baggage scanner : computer based multi energy X-Ray Baggage Inspection System mounted on castor wheels capable of passing through bags of dimensions 900 mm (W) X 900 mm (H) with 22”/24 LCD Monitor, Input / Output rollers with frames. incluiding Server , required Computer Hardware & UPS etc.

SUB HEAD XXXVI : DOOR FRAME METAL DETECTORS

Supply, Installation, Testing & Commissioing of IP65 Rated Mircroprocessor Based PC compatible DFMD with 8 zone detection, auto Calibration, infra red occupancy sensor of traffic counter, 2 hour battery back. It shall meets or exceeds all industry safety and electromagnetic compatibility (EMC) standards and conforms to international directives. Safe for users of heart pacemakers, pregnant women and magnetic recording materials and magnetic strips. Required accessories & Hardware shall be included as complete.

Supply, fixing, Testing & Commissioning of Handheld Metal Detector

SUB HEAD XXXVII: BOOM BARRIERS

Supply, installation, Testing & Commissioning of 3 Meter boom barrier with anti-corrosion coating (push button operated as well as reader operated) with pair of photo cell, support, wireless remote controle button, flashing light, IR Photo cell alongwith security induction loop ( Internal & External ) for boom gate operation on both side incluiding civil work, fabriacation, induction cables, conduits as complete.

Supply, installation, Testing & Commissioning of 4 Meter boom barrier with anti-corrosion coating (push button operated as well as reader operated) with pair of photo cell, support, wireless remote controle button, flashing light, IR Photo cell alongwith security induction loop ( Internal & External ) for boom gate operation on both side incluiding civil work, fabriacation, induction cables, conduits as complete.

Supply, Installation, Testing & Commissioing of Open Close Push Button Station

Supply, Installation, Testing, Commissioning of IP Based Two Door Controller along with all the necessary mounting accessories.

Supply & Installation of 80mm HDPE Pipe (supply, digging, excavation, laying & backfilling to be considered)

Supply, Installation, Testing, Commissioning of Long Range Multi-Format Card Reader along with all the necessary mounting accessories.

Supply & printing of Printable smart card for driver

Supply, Configuration & Fixing of Long range RFID tag for Vehicles

Supply & laying of 3C X 2.5 sq.mm Cu. XLPE insulated armoured cable

Supply & laying of 4C X 1.5 sq.mm Cu. XLPE insulated armoured cable

SUB HEAD XXXVIII : TURNSTILES

Supply, Installation, Testing & Commissioning of Single lane One side Flap Barrier with anti-corrosion Coating. Shall have mimimum 550mm wide (reader operated) with required standard mouting accessories.

Supply, Installation, Testing & Commissioning of Single lane both side Flap Barrier with anti-corrosion Coating. Shall have mimimum 550mm wide (reader operated) with required standard mouting accessories.

Supply, Installation, Testing & Commissioning of Full Hieght Dual Lane turnstile anti-corrosion Coating. shall have Height of Turnstile – 2.2m. & Passage clearance height is 2m & width is 1.5 m, High Speed- Min. 40 Person / Minute. Turnstile shall support to push button as well as card operated for pedestrain entry at Entry Gate with standard mouting accessories.

Supply, Installation, Testing & Commissioning of Full weist Half Hieght Traipod with anti-corrosion Coating. shall have Passage clearance height is 420mm, High Speed- Min. 30 Person / Minute. Triapod shall support to push button as well as card operated for pedestrain entry at Entry Gate with standard mouting accessories.

Supply, Installation, Testing & Commissioing of Open Close Push Button Station

SUB HEAD XXXIX: AUTOMATIC NAME PLATE RECOGNITION (ANPR) SYSTEM

Supply, Installation, Testing, Commissioning of Automatic Number Plate Recognition (ANPR) Camera with Vehicle Monitoring System software for gate control, ANPR and Driver image capturing with required license. Software should be integrate with third party software like Access control & VMS.

Supply, Installation, Testing, Commissioning of Vehicle Monitoring System software for gate control, ANPR and Driver image capturing with required license. Software should be integrate with third party software like Access control & VMS.

Supply, Installation, Testing, Commissioning of Work station (Server Intel Xeon Quad core, 2.66 Ghz , 4 Mb L2 Cache, Memory 16GB,HDD 2TB . Keyboard / Joystic & mouse with Windows Server 2012 enterprise OS & antivirus with 5 year subscriptions and standard accessories.

Supply, Installation, Fixiting & Commissioning of Anti-Corrasion coated Poles of required height for ANPR, Driver image capture camera, Long & Short range RFID with necessary height with required civil foudation, mouting accessories etc.

SUB HEAD XL : NETWORK STRUCTURED CABLING SYSTEM

Supply, installation, testing and commissioning of IP based DATA & LAN Networking system complete with all necessary hardware, accessories & following items as required to complete the system. Contractor/ System Integrator shall submit 25 years performance certificate from Respective OEM. Refer Technical Specifications for OFC and allied extra low voltage work.

Supply, laying, testing and commissioning of 24 Core Outdoor OS2 Single mode Optical Fiber Cable (9/125µm). Outdoor, Corrugated steel tape loose tube Yellow jacket through existing GI/ HDPE/ Hume pipes or on cable trays inside the cable duct including all necessary fixing accessories for e.g. cable ties, hardware etc., including outdoor type fiber optic cable joint with all necessary accessories, jointing kit similar to Make : Raychem/ equivalent, complete as required. (Refer technical specifications for OF cables).

Supply, laying, testing and commissioning of 12 Core Outdoor- OS2 Single-mode Optical Fiber Cable (9/125µm). Outdoor, Corrugated steel tape loose tube Yellow jacket through existing GI/ HDPE/ Hume pipes or on cable trays inside the cable duct including all necessary fixing accessories for e.g. cable ties , hardware etc., including outdoor type fiber optic cable joint with all necessary accessories, jointing kit similar to Make : Raychem/ equivalent, complete as required. (Refer technical specifications for OF cables).

Supply, laying, testing and commissioning of 6 Core Outdoor- OS2 Single-mode Optical Fiber Cable (9/125µm). Outdoor, Corrugated steel tape loose tube Yellow jacket through existing GI/ HDPE/ Hume pipes or on cable trays inside the cable duct including all necessary fixing accessories for e.g. cable ties , hardware etc., including outdoor type fiber optic cable joint with all necessary accessories, jointing kit similar to Make : Raychem/ equivalent, complete as required. (Refer technical specifications for OF cables).

Providing & Installation of 9/125µm SM Duplex Connectors (LC Pigtails OS2- 09/125mn)

Supply & fixing of 6 port Adapter plate, loaded with 3 nos. of duplex SC unit for 6 Single mode fibers of size 9/125 µm .Adapters to be compatible to fit in 19" 24/48 port LIU.

Supply, installation, termination & testing of LIU 24 port . Rack Mount 19" modular type unloaded to be compatible for 4nos of 6 X RJ 45 UTP unit in a block or 6 port SC/LC/ST adapter unit.

Supply, installation, termination & testing of Fiber Optic Splice Tray. 24 Fiber Capacity Cassette for pigtails cassette as fiber optic unit in modular type which could be fitted in rack end.

Supply & Fixing of Blanking plate for LIU and Modular Patch Panel (6XRJ45 Blanking plate). For 19" Panel - Black in colour).

Supply, installation, termination & testing of SM OS2 Patch Cord -SC/SC Duplex Cords - 2 mtrs.

Supply, installation, termination & testing of SM OS2 Patch Cord -SC/LC Duplex Cords - 2 mtrs.

Supply, installation, termination & testing of SM OS2 Patch Cord -LC/LC Duplex Cords - 2 mtrs.

Supply and fixing of modular type Quad Port RJ - 45 (Data/Voice) including front plate and anodised GI box in concealed manner of adequate sizes, including all fixing accessories.

Supply and fixing of modular type Triplel Port RJ - 45 (Data/Voice) socket including front plate and anodised GI box in concealed manner of adequate sizes, including all fixing accessories.

Supply and fixing of modular type Dual Port RJ - 45 (Data/Voice) socket including front plate and anodised GI box in concealed manner of adequate sizes, including all fixing accessories.

Supply and fixing of modular type Single Port RJ - 45 (Data/Voice) socket including front plate and anodised GI box in concealed manner of adequate sizes, including all fixing accessories.

Supply and laying of 25mm dia. Heavy gauge PVC conduit concealed in wall/ ceiling/ Slab and drawing of 12 SWG GI wire as fire wire for laying of LAN/ Internet/ ELV Cables at a later stage and supply of all fixing accessories such as junction boxes, conduit bends, etc., complete as required.

Supply and laying of 32mm dia. Heavy gauge PVC conduit concealed in wall/ ceiling/ Slab and drawing of 12 SWG GI wire as fire wire for laying of LAN/ Internet/ ELV Cables at a later stage and supply of all fixing accessories such as junction boxes, conduit bends, etc., complete as required.

Supply and laying of unarmoured CAT-6 UTP data cable in existing conduit/ hume pipe

Supply and laying of armoured CAT-6 F/STP data cable in existing conduit/ hume pipe

Supply & Fixing of 19" Modular Patch Panel, unloaded Toolless Crimp CAT6 U/UTP 24 port rack mountable to be compatible in 4nos of 6 X RJ 45 Tool less Keystone connector U/UTP unit in a block.

Supply and fixing of modular type RJ - 45 Outlet for Data/Voice for modular Jack Panel including all fixing accessories.

Supply & fixing of CAT-6 UTP Patch Cord - 1 mtr (Factory crimped Patch cord in Light Blue colour.)

Supply & fixing of CAT-6 UTP Patch Cord - 2 mtr (Factory crimped Patch cord in Light Blue colour.)

Supply & fixing of 2 Pair RJ-11 Patch Cord - 1 mtr (Factory crimped patch cord in white colour)

Supply and fixing of Krone telephone tag block of 20 Pair in and including MS enclosure, interconnecting jumper wires, termination and fixing accessories, concealed in wall, complete as required.

Supply and fixing of Krone telephone tag block of 50 Pair in and including MS enclosure, interconnecting jumper wires, termination and fixing accessories, concealed in wall, complete as required.

Supply and fixing of Krone telephone tag block of 100 Pair in and including MS enclosure, interconnecting jumper wires, termination and fixing accessories, concealed in wall, complete as required.

Supply and fixing of Krone telephone tag block of 200 Pair in and including MS enclosure, interconnecting jumper wires, termination and fixing accessories, concealed in wall, complete as required.

Supply and fixing of Krone telephone tag block of 400 Pair in and including MS enclosure, interconnecting jumper wires, termination and fixing accessories, concealed in wall, complete as required.

Supply and laying of 20 Pair armoured 0.5mm dia Jelly filled copper conductor armoured Cables in vertical shaft / cable tray in ceiling as required and as directed by Engr-in-charge. The cable shall be as per the DOT specifications.

Supply and laying of 50 Pair armoured 0.5mm dia Jelly filled copper conductor armoured Cables in vertical shaft / cable tray in ceiling as required and as directed by Engr-in-charge. The cable shall be as per the DOT specifications.

Supply and laying of 50 Pair armoured 0.5mm dia Jelly filled copper conductor armoured Cables in ground at 750mm below ground level including excavation, and refilling of earth, laying & jointing of cables, providing protection with bricks on top and sides and Telephone cable route markers at every 50mtrs interval complete as required and as directed by Engr-in-charge. The cable shall be as per the DOT specifications.

Supply and fixing of 48 or 50 Port High density CAT-3 Jack panel with standard accessories & Hardware

Supply & Punching of 2 Pair Jumper Wire

Supply & Fixing of Home Conenct box for Flat to accommodate 1 Nos X 12 Port wall mount panel , 1 Nos. X 6 Port Network Switch & Cable Management. Box should be Powder coated made of CRCA Sheet, Compact in Size, Ventilation, Toughened tinted Glass Door with required mouting accessories & hardware as complete. Note: Sample of Box to be approved from Architect/ Consultant.

Supply & Fixing of Home Conenct box for Flat to accommodate 2 Nox x 12 Port wall mount panel , 1 Nos X 6 Port Network Switch & Cable Management. Box should be Powder coated made of CRCA Sheet, Compact in Size, Ventilation, Toughened tinted Glass Door with required mouting accessories & hardware as complete. Note: Sample of Box to be approved from Architect/ Consultant.

Supply and installation of suitable size of Cable TV Tap-Off boxes to house one incoming and six outgoing electronic splitter along with required mouting accessories & hardware to mount in Home Connect Box.

Supply and installation of suitable size of Cable TV Tap-Off boxes to house one incoming and Four outgoing electronic splitter along with required mouting accessories & hardware to mount in Home Connect Box.

Supply, installation & Termination of 12 Port Wall mount Jack Panel with loaded RJ-45 Outlet with required mouting accessories & hardware to mount in Home Connect Box.

Supply and laying of RG-6 co-axial TV cable in existing PVC conduit with required accessories & hardware

Supply and laying of RG-11 co-axial TV cable in existing PVC conduit with required accessories & hardware

Supply & fixing of 42U Cabinet. Size 2026 X 800 X 800 mm (HXWXD) following accessories, Width (mm) 800, Depth (mm) 800, Approx.Net Wt. (kg) 150, CRCA 'D' Grade thickness (mm) 1.2, RAL 9017 (Matt Black), Glass: 4mm Toughened Tinted Glass Door, Injected one piece polyurethane gasket on frame, Accessories: Cooling Fan (230V A/C 90 CFM) - 4 Nos, PDU 230VAC - 2 No (6 nos. 6A/16A sockets with plugs 6A/16A - 1/1pc & MCB 16A/32A - 0/1 Pc), Cable Channel 100mm wide 42U- 2 Nos, Heavy Duty Stationary Shelf 600mmW x 475mmD - 1 No, Earthling Strips 150mm H - 1 No, Door Lock - 1 No, Castor Wheels (with Brake) - 2 Nos, Castor Wheels (without Brake) - 2 Nos, Front Metal Band - 1 No. Packing: 5 ply cardboard & Inside 28 ply EP foam. In the rack there must be maintained 1 U = 1.75 inches space.

Supply & fixing of 42U Cabinet. Size 2026 X 800 X 1000 mm (HXWXD) following accessories, Width (mm) 800, Depth (mm) 800, Approx.Net Wt. (kg) 150, CRCA 'D' Grade thickness (mm) 1.2, RAL 9017 (Matt Black), Glass: 4mm Toughened Tinted Glass Door, Injected one piece polyurethane gasket on frame, Accessories: Cooling Fan (230V A/C 90 CFM) - 4 Nos, PDU 230VAC - 2 No (6 nos. 6A/16A sockets with plugs 6A/16A - 1/1pc & MCB 16A/32A - 0/1 Pc), Cable Channel 100mm wide 42U- 2 Nos, Heavy Duty Stationary Shelf 600mmW x 475mmD - 1 No, Earthling Strips 150mm H - 1 No, Door Lock - 1 No, Castor Wheels (with Brake) - 2 Nos, Castor Wheels (without Brake) - 2 Nos, Front Metal Band - 1 No. Packing: 5 ply cardboard & Inside 28 ply EP foam. In the rack there must be maintained 1 U = 1.75 inches space.

Supply & fixing of 24 /21U Wall-mounting cabinets. size around 800X600mm (WXD) with all standard accessories. Width (mm) 600, Depth (mm) - 500, CRCA 'D' Grade thickness (mm) - 1.2, RAL 9017 (Matt Black), Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Earthling Strips 150mm H - 1 No, Wall Screws (4 sets of 2'' screws, washer, rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained1 U = 1.75 inches space.

Supply & fixing of 30 /32U Floor-mounting cabinets. size around 800X600mm (WXD) with all standard accessories. Width (mm) 600, Depth (mm) - 500, CRCA 'D' Grade thickness (mm) - 1.2, RAL 9017 (Matt Black), Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Earthling Strips 150mm H - 1 No, Wall Screws (4 sets of 2'' screws, washer, rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained1 U = 1.75 inches space.

Supply & fixing of 15U Wall/ Floor-mounting cabinets. size around 600X500mm (WXD) with all standard accessories. Width (mm) 600, Depth (mm) - 500, CRCA 'D' Grade thickness (mm) - 1.2, RAL 9017 (Matt Black), Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Earthling Strips 150mm H - 1 No, Wall Screws (4 sets of 2'' screws, washer, rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained1 U = 1.75 inches space.

Supply & fixing of 9U Wall-mounting cabinets. size around 600X500mm (WXD) with all standard accessories. Width (mm) 600, Depth (mm) - 500, CRCA 'D' Grade thickness (mm) - 1.2, RAL 9017 (Matt Black), Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Earthling Strips 150mm H - 1 No, Wall Screws (4 sets of 2'' screws, washer, rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained1 U = 1.75 inches space.

Supply & fixing of 19" Rack mountable 1U PVC Cable Manager

Supply & fixing of Mounting Hardware (20 sets of M6 screws, washer, cage nuts (nickel coated).

Supply, installation, termination & testing of 21U Outdoor & Weatherproof cabinets including painted MS stand. (1100X800X800 (HXWXD)) with all standard accessories. Width (mm) 800, Depth (mm) - 800, Approx.Net Wt. (kg) - 32, CRCA 'D' Grade thickness (mm) - 1.2, RAL 9017 (Matt Black), Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Cable Manager Metal - 3 Nos, Earthling Strips 150mm H - 1 No, Mounting Hardware (20 sets of M6 screws,washer,cage nuts (nickel coated)) - 1 No, Wall Screws (4 sets of 2'' screws, washer, rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained1 U = 1.75 inches space.

Supply & Crimping of RJ45 Connector ( Packet of 100 Nos.)

Supply , Installation, Splicing & Testing of Outdoor IP rated 68 Type Fiber Optic Joint unit for 6-24 Core single mode (OS2) optical fiber with all accessories etc., complete as required.

Supply & fixing of CAT6A/E 15 feet Patch Cord with required accessories as completed

Supply and laying of 80mm dia. Class B G.I. pipes for road crossings, laid 750mm below ground level including excavation, back filling, long radius bends etc., complete.

Supply and laying of 50mm dia. Class B G.I. pipes for road crossings, laid 750mm below ground level including excavation, back filling, long radius bends etc., complete.

Supply and laying of 63mm dia. PLB HDPE Telecommunications Duct as per TEC (O.D. - 63mm & I.D. - 51mm) including suitable jointing kit/ coupler at both ends & providing Nylon/P.P. rope for laying of LAN/ Internet/ OF Cables drawn through HDPE pipes properly at the time of laying pipes, duct shall be smooth outside, free from blisters, shrink hole, scratches & roughness etc. The Inner layer shall be spirally ribbed, duct shall be laid 750mm below ground level excluding excavation in all kind of soil, horizontal drilling, SDR, refilling of earth after HDPE pipes are laid etc., Raw material of the duct shall be PE 63 Grade UV. (Supply and laying of HDPE pipe with accessories without excavation/ civil works).

Supply and laying of 110mm dia. PLB HDPE Telecommunications Duct as per TEC (O.D. - 110mm & I.D. - 98.7mm) including suitable jointing kit/ coupler at both ends & providing Nylon/P.P. rope for laying of LAN/ Internet/ OF Cables drawn through HDPE pipes properly at the time of laying pipes, duct shall be smooth outside, free from blisters, shrink hole, scratches & roughness etc. The Inner layer shall be spirally ribbed, duct shall be laid 750mm below ground level excluding excavation in all kind of soil, horizontal drilling, SDR, refilling of earth after HDPE pipes are laid etc., Raw material of the duct shall be PE 63 Grade UV. (Supply and laying of HDPE pipe with accessories without excavation/ civil works).

Constructing masonry Chamber 90 x 90 x 90 cm, inside with 75 class designation work in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve, with C.I. space box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1 : 3 (1 cement " 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design:

Supply, installation, testing and commissioning of 1000VA, single phase UPS with 3 hours battery back-up using sealed maintenance free batteries (2Nos. X 200AH), suitable rating of 4P MCB in and including weatherproof enclosure outside of the rack, interconnecting copper cables from MCB to UPS and UPS to batteries, SNMP Card, UPS remoterely monitoring software, built-in surge protection device etc. in above IP 54 enclosure/ rack. Contractor shall submit battery back-up calculation. UPS shall have soft communication ports for remotely monitoring.

Supply, installation, testing and commissioning of 3000VA, single phase UPS with 3 hours battery back-up using sealed maintenance free batteries (6Nos. X 200AH), suitable rating of DP MCB in and including metal enclosure, interconnecting copper cables from MCB to UPS and UPS to batteries, SNMP Card, UPS remoterely monitoring software, built-in surge protection device etc. in above IP 54 enclosure/rack. Contractor shall submit battery back-up calculation. UPS shall have soft communication ports for remotely monitoring.

Supply and fixing of modular type TV outlet including front plate and anodised GI box in concealed manner of adequate sizes, including all fixing accessories.

Supplying and erecting PVC ROHS complied Non flame propagting under floor ducts/raceways of 60mm Width x 25 mm depth x 3000 mm Length including the connectors and the clamps at required intervals complete. The ducts shall be in trapezoidal shape tested 750 N p with required mouting accessories.

Supplying and erecting PVC ROHS complied Non flame propagting under floor ducts/raceways of 90mm Width x 35 mm depth x 3000 mm Length including the connectors and the clamps at required intervals. The ducts shall be in trapezoidal shape tested for 750 N p with required mouting accessories.

Supplying and erecting underfloor junction box of size 150mm x 150mm x 55 mm with flush finish powder coated appearance having knock outs for UPVC duct entry of size 60x25 mm width and 95x35 mm ducts complete as per specification.

Supplying and erecting of underfloor junction box of size 260mm x 260mm x 55 mm.with flush finish powder coated appearance having knock outs for UPVC duct entry of size 60x25 mm and 95x35 mm ducts complete as per Specification.

Supplying and erecting underfloor junction box of size 300mm x300mm x55 mm. with flush finish powder coated appearance having knock outs for UPVC duct entry of size 60x25 mm and 95x35 mm ducts complete as per specification.

Supplying and erecting underfloor junction box of size 355mm x 355mm x55 mm. with flush finish powder coated appearance having knock outs for UPVC duct entry of size 60x25 mm and 95x35 mm ducts complete as per specification.

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. Ordinary rock

Providing and Laying RCC Precast Tiles etc completed as per instruction of Engineer In Charge

SUB HEAD XLI : LAN & WAN SYSTEM

Supply, installation, testing & commissioning of Layer 3 Switch: 24 100/1000 BaseX SFP, 4 1G/10G SFP+, 4 SFP28 (1G/10G/25G) ports and 2 QSFP28 VFL ports. All ports except VFL are MACsec capable with Dual power supply unit and next day business support. Inclusive of required hardware, software, license, Mounting accessories & Patch cords.

Supply, Installation, Commissioning & Testing of L2 Managed Switch: 24 RJ-45 10/100/1G BaseT, 2 fixed SFP (1G), 4 fixed SFP+ (1G/10G) uplink/stacking ports with dual power supply unit & next day business support. Inclusive of required hardware, software, license , Mounting accessories & Patch Cords.

Supply, Installation, Commissioning & Testing of L2 Managed Switch: 48 RJ-45 10/100/1G BaseT, 2 fixed SFP (1G), 4 fixed SFP+ (1G/10G) uplink/stacking ports with dual power supply unit & next day business support. Inclusive of required hardware, software, license , Mounting accessories & Patch Cords.

Supply, Installation, Commissioning & Testing of L2 Managed Switch: 24 RJ-45 PoE 10/100/1G BaseT, 2 fixed SFP (1G), 4 fixed SFP+ (1G/10G) uplink/stacking ports and 500W PoE power budget with dual power supply unit & next day business support. Inclusive of required hardware, software, license , Mounting accessories & Patch Cords.

Supply, Installation, Commissioning & Testing of L2 Managed Switch: 48 RJ-45 PoE 10/100/1G BaseT, 2 fixed SFP (1G), 4 fixed SFP+ (1G/10G) uplink/stacking ports and 800W PoE power budget with dual power supply unit & next day business support. Inclusive of required hardware, software, license , Mounting accessories & Patch Cords.

Supply, fixing, Testing & Commissioning of 10 Gigabit optical transceiver SFP+). Supports monomode fiber over 1310nm wavelength nominal) with an LC connector. Typical reach of 10Km on 9/125 m SMF.

Supply, installation, testing & commissioning of 10 GBase-T Gigabit Ethernet Transceiver SFP - Supports category 6 & 6E copper cabling up to 30m. SFP works at 10 Gbit/s speed and full-duplex mode.

Supply, Installation, Testing & Commissioning of 1000Base-LX Gigabit Ethernet optical transceiver SFP MSA). Supports single mode fiber over 1310nm wavelength nominal) with an LC connector. Typical reach of 10 Km on 9/125 m SMF.

Supply, fixing, Testing & Commissioning 10/100 Duplex Media Convertor with standard mounting hardware & accessories.

Supply, installation, testing & commissioning of Industrial grade layer 2 Gigabit Ethernet fixed configuration compact fan-less chassis with 8 RJ-45 10/100/1000 Base-T PoE+ ports out of which 4 ports are 60W PoE capable, 4 100/1000 Base-X SFP ports, RS-232 Console (RJ45), 1 Alarm relay Input, 1 alarm relay output and USB port. Inclusive of required hardware, software, license & Mounting accessories & patch cords.

Supply, fixing, testing & commissioning of 1000Base-LX industrial Gigabit Ethernet optical transceiver (SFP MSA) Module with standard accessories.

Supply, installation, testing & commissioning of layer 2 Gigabit Ethernet fixed configuration compact fan-less chassis with 8 RJ-45 PoE 10/100/1G BaseT, 2 10/100/1G BaseT, 2 fixed SFP (1G) uplink ports. 1RU size, internal ACpower supply (120W PoE budget). Inclusive of required hardware, software, license & Mounting accessories & patch cords.

Supply, fixing, testing & commissioning of 1000Base-T Gigabit Ethernet Transceiver SFP MSA) - Supports category 5, 5E, and 6 copper cabling up to 100m. SFP works at 1000 Mbit/s speed and full-duplex mode.

S/I/T/C of Central Control Managment based Dual radio 2.4/5Ghz 2x2 802.11ax, omni antenna. 1x GbE uplink, 4x GbE downlink (1 PSE), RJ45 passthrough pair, 1x USB and 1x 48V. for Guest Room under study table with license and standard Accessories & option of Table/ceiling/wall mouting .

S/I/T/C of Central Control Managment based Dual radio 2.4/5Ghz 2x2 802.11ax, omni antenna. 2x 1GE up, indoor type wireless device for inddor application incld license with standard Accessories & option of ceiling & wall mouting . ( 1.7 Gb)

S/I/T/C of Central Control Managment based Dual radio 5GHz 4x4:4 / 2.4GHz 2x2:2 802.11ax, Outdoor type wireless integrated omni. 1x1 scanning radio and BLE radio. 2.5GbE, 1GbE, 1GbE SFP, USB, 48V DC. For outdoor application incld license with standard Accessories & option of ceiling & wall mouting . ( 2.9 Gb)

S/I/T/C of software / Hardware based N+1 Redundancy Wireless Controller system with support to IEEE 802.11a/b/g/n/ac/ax, shall have standard features like management, QoS & Security. (will expandable to 4000 devices)

SUB HEAD XLII: TELEPHONY SYSTEM

Supply, Installation, testing & commissioning of IPPBX support with geographical Redundant servers in hot standby mode, Server-Gateway distributed architecture with centralized call control over the IP backbone with all feature and functionalities, support to Minimum 900 extension as per technical specifications. The active server will hosted at Security room and redundant call servers shall be hosted at Server Room. cost shall be included with required server hardware, associates license, OS software enterprise/professional as compatible MacAfee /Symantec Anti virus & All other related software such MS office with liscesenced. Refer specification sheet for details.

Supply, installation, testing and commissioning of industrystandard server with minimum 2.8GHz 4-core 1P 16GB-U 2LFFNHP 290W 1TB SATA 7.2K LFF SC MV HDD Smart Array Controller cost shall have include with required license, software , associates card & Cable as per specification.

Supply, Installation, testing & commissioning of Rack MountableMedia Gateway equipped with 100 Nos. Analogue, 212 Nos. IP Phone, 08 Nos Analogue Trunks & 02 Nos. PRI, exchange shall have Redundancy - Hot standby, Hot swappable, duplicate control cards and duplicated power supply unit, no single point of failure and no dropping of established calls even during changes over of duplicate cards. cost shall have include with required license, software, associates card & Cable as per specification.

Supply, Installation, testing & commissioning of Rack Mountable Media Gateway and equipped with 90 Nos. Analogue Extensions. cost shall have include with required license, software, associates card & Cable as per specification.

Supply, Installation, testing & commissioning of Rack Mountable Media Gateway and equipped with 60 Nos. Analogue Extensions. cost shall have include with required license, software, associates card & Cable as per specification.

Supply, Installation, testing & commissioning of Rack Mountable Media Gateway and equipped with 36 Nos. Analogue Extensions. cost shall have include with required license, software, associates card & Cable as per specification.

Supply, Installation, testing & commissioning of Rack Mountable Media Gateway and equipped with 24 Nos. Analogue Extensions. 2 Slot Extra for Trunk Card & PRI Card. cost shall have include with required license, software, associates card & Cable as per specification.

Supply, Installation, testing & commissioning of Analogue Phones including required wall/desk mounting accessories & hardware. Phone shall be as per specifications

Supply, Installation, testing & commissioning of Analogue Guest Phones with Short keys including required wall/desk mounting accessories & hardware. Phone shall be as per specifications

Supply, Installation, testing & commissioning of IP Phones with 10/100 Ethernet Port, HD Audio, PoE including required SIP License & Software. Phone shall be as per specification.

Supply, installation, testing & commissioning of 6 Line IP-Multimedia Phones with a 4.3” capacitive touch screen, The phone features Gigabit ports, HD audio and HD video, a built-in web browser, integrated Wi-Fi for network flexibility, PoE, and a tiltable CMOS camera (with Privacy Shutter). including required SIP license & software. Phone shall be as per specifications

Supply, Installation, testing & commissioning of IP Desk phone Based Operator Console with 42 Keys including required license & software. Phone shall be as per specifications

Supply, Installation, testing & commissioning of 30 Channel PRI Card with required Accessories.

SUB HEAD XLIII: AUDIO VIDEO SYSTEM

AV, DRAPERY & STAGE LIGHTING SYSTEM FOR AUDITORIUM

Supply, Installation, Testing & Commissioing of Loudspeaker : 2 Way Progressive directivity Loudspeaker Array. Individual loudspeaker modules within the array shall meet the following criteria: Usable Frequency Range (-10dB) of 55 Hz - 18 kHz and Continuous Power Handling of >=600W LF + 150W MF-HF. There shall be LF driver of at least 14" in each module, and 6 compression drivers of 2" voice coil or better in a CADS Manifold. The Loudspeaker shall have a Max. SPL (Peak) of >=128 dB or better for LF and 133dB for MF-HF. It should have suitable Drivers for LF and MF/HF with Horizontal dispersion pattern of 90º or better (with multiple waveguide options, Vertical dispersion of the array shall be 60 degrees or better. The loudspeaker module shall be comprised of a shall be of Baltic birch plywood construction with IP55 weather rating incluiding Ceiling Mounting Kit & standard accessories as per the tender specifications.

Supply & Installation of Mouting Kit : Flying array frame and other necessary hardware for suspending main speaker arrays. All necessary hardware to be included to achieve a safety factor of 8:1 or better. Incluiding all required accessories, Hardware & rope as required.

Supply, Installation, Testing & Commissioing of 18" arrayable subwoofer having a Freq. Range of 29Hz - 300Hz. It should have an ground stack position Sensitivity of > = 98dB (1W/1m) or more delivering a ground position Max. Calculated SPL(peak) of >=135 db. The loudspeaker should have a nominal impedance: 4ohm or more and continuous AES Power Handling of 1250W or more. Shall be enclosed in Baltic birch plywood with standard Array rigging hardware for Cardioid as well as stacked position. The subwoofer shall have the same footprint as the main array speakers and shall have provision for suspending on top of main LR arrays. The loudspeaker module shall be comprised of a shall be of Baltic birch plywood construction with IP55 weather rating incluiding Ceiling Mounting Kit & standard accessories as per the tender specifications.

Supply, Installation, of Hanging/ Suspension arrangement for Subwoofer. Incluiding all mounting accessories, Hardware & Rope as completed.

Supply, installation, testing & Comissioning of passive coaxial two-way point source loudspeaker with a single 8" LF driver or better. Frequency Range (-10dB) of 75Hz - 20kHz or better & Continuous Power Handling of >= 150W or better. The Loudspeaker module shall have a Max. SPL (Peak) of MF/HF>= 128 or better. It should have Horizontal near dispersion pattern of 110º or better, vertical dispersion of the module shall be 60 degrees or better. The loudspeaker module shall be comprised of a shall be of Baltic birch plywood construction with IP55 weather rating incluiding Ceiling Mounting Kit & standard accessories as per the tender specifications.

Supply, installation, testing & Comissioning of Digital Dante Amplifier with Max output power of 4x1200W@4-8Ohms, 70V or 100V or bridged mode output power of 2x3000W@4ohms. Frequency response of 20 Hz - 20 kHz, SNR of >110 dB(A and THD+N < 0.1%. With Multiple channel metering LED and attenuation controls. PEQ, band pass, Spkr EQ, limiter, delay. Maximum input level 20 dBu. 4 Digital channels via Dante, with Euroblock, 8-pin connectors for Analog outputs. Software and hardware controlled. Sample rate 24-bit, 44.1 kHz – 192 kHz. inlcuiding all required patch cord, Modules & Mounting Hardware as completed.

Supply, installation, testing & Comissioning of Integrated high impedance Class D Dual Zone Amplifier with output power of 2 x 120 W @ 70/100 V ; Frequency Response - 55 Hz - 20 kHz (+0/-3 dB, @ 1 W reference 1 kHz) ; THD+N - ≤1 % (at full rated power); Channel Separation (Crosstalk) - ≤-60 dBV (below rated power, 1 kHz); A/D and D/A Converters - 24-bit / 48 kHz; Audio Latency - 10.4 ms - (any input to speaker output or aux output); THD <0.3% at rated power. Channel Separation ≤ –60 dBV (below rated power, 1 kHz), Dynamic range > 88 dB. Maximum Input Level : +10 dBV or better. 1 balanced page/priority input, 3 unbalanced line inputs; built in loudspeaker EQs. Shall include output for expansion amplifier and remote controller (Wired) for source as well as volume control. inlcuiding all required patch cord, Modules & Mounting Hardware as completed.

Supply, installation, testing & Comissioning of pre-polarized condenser Gooseneck Microphone with modes-Toggle on/off,Push to mute,Push to talk, permanent on (external LED control), gooseneck microphone with an overall length of minimum 450 mm and with XLR3M-type connector at its base, which shall offer radio frequency interference (RFI) shielding against intermodulation from wireless equipment or devices, cardioid microphone capsule with uniform 120° angle of acceptance (-3dB) or better, frequency response of 50 Hz to 20,000 Hz or better and sound input levels handling capability of minimum 130 dBspl, nominal equivalent noise level of 26 Dba or better and output shall be low impedance balanced (<100 ohms) with current consumption shall be 3 mA or better with table stand for connecting and operating XLR gooseneck microphones shall be rugged and unobtrusive with XLR-3F microphone input and an XLR-3M microphone output operating on 48 V phantom power and current consumption of 3.7 mA or better. Incluiding required all accessories as completed.

Supply, installation, testing & Comissioning of wireless head worn microphone with omnidirectional polar pattern,condenser microphone ,frequency response 50Hz-20kHz,RF sensitivity < 1.0 Uv,Image rejection>60dB,Dynamic range >100dB and receiver having 1112 channels possible,S/N ratio >100dBA, dynamic range >100db B,distortion <1 %,frequency band:648-676MHz,modulation:+/-40kHz; Incluiding all required accessories as completed.

Supply, installation, testing & Comissioning of Handheld Wireless Mic with Cardioid polar pattern,dynamic microphone ,frequency response 45Hz-15kHz,RF sensitivity < 1.0 Uv,Image rejection>60dB,Dynamic range >100dB and receiver having 1112 channels possible,S/N ratio >100dB A,dynamic range >100db B,distortion <1 %,frequency band:648-676MHz,modulation:+/-40kHz; incluiding all required accessories as completed.

Supply, Installation, testing & commissioning of Shotgun Microphone with Type of transducer : Condenser; Polar Pattern : Cardioid / hypercardioid / supercardioid/ Lobe Pattern; Freq Response : 40Hz to 19kHz or better; Sensitivity : 21.1mV/Pa or better complete with all standard accessories as per the tender specifications.

Supply , installation , testing and commissioning of digital Manual mixer with minimum features 12 recallable mic pre amps, 12 mono mic inputs, 4 line inputs, AES in and out, Massive mix capacity – 12 inputs to mix in a small format live sound digital mixer.

Supply, Installation, Testing & Commissioing of Wired Handheld Microphone: Dynamic Cardioid polar pattern, Frequency Response: 40 Hz to 16 kHz; Sensitivity: 2,7 mV/Pa; Excellent feedback rejection;Rugged metal housing with Switch & standard accessories as per the tender specifications.Supply, Installation, Testing & Commissioing of Wired Handheld Microphone: Dynamic Cardioid polar pattern, Frequency Response: 40 Hz to 16 kHz; Sensitivity: 2,7 mV/Pa; Excellent feedback rejection;Rugged metal housing with Switch & standard accessories as per the tender specifications.Supply, Installation, Testing & Commissioing of Wired Handheld Microphone: Dynamic Cardioid polar pattern, Frequency Response: 40 Hz to 16 kHz; Sensitivity: 2,7 mV/Pa; Excellent feedback rejection;Rugged metal housing with Switch & standard accessories as per the tender specifications.Supply, Installation, Testing & Commissioing of Wired Handheld Microphone: Dynamic Cardioid polar pattern, Frequency Response: 40 Hz to 16 kHz; Sensitivity: 2,7 mV/Pa; Excellent feedback rejection;Rugged metal housing with Switch & standard accessories as per the tender specifications.

Supply , installation , testing and commissioning of Antenna Splitter and combiner for wireless Microphone

Supply of Light cations. weight tripod alluminium Microphone stand with Long Arm, boom type & chrome plating with standard mouting accessories per the tender specifications.

Supply , installation , testing and commissioning of 3-pin, Single XLR-female table mount plate, Connector should be neutrick only.

Supply and fixing of 3 point XLR mic wall mount junction boxes with one Speakon Connector as per the tender specifications.

Supply and fixing of 1 point XLR mic junction boxes with one Speakon Connector as per the tender specifications.

Supplyb of CD player with USB as per the tender specifications.

Supply and laying of2 core 12 AWG/4 Sq mm, Twisted, unshielded Speaker cable with stranded annealed bare copper conductors, Semi-rigid PVC insulation, NEC CL3R, CEC CMG, RoHS compliant as per the tender specifications.

Supply and laying of 2 core 14 AWG/2.5 Sq mm, Twisted, unshielded Speaker cable with stranded annealed bare copper conductors, Semi-rigid PVC insulation, NEC CL3R, CEC CMG, RoHS compliant as per the tender specifications.

Supply of UL Listed Connectors as per the tender specifications.

Supply, lnstallation, Testing & installation of Minimum 136" Diagonal sie of Wall / Ceiling Mount LED Wall with 600 Nits , 2.5.mm pixel LED wall tiles of 600mm x 337.5mm to make a LED wall along with controller & processor to construct a led wall having a display area of Minimum 56 sq Feet having an aspect ratio of 16:9 in a Cabinet made up of diecast Aluminium. The LED wall should have Viewing Angle 160 Degree (horizontal) X 150 degree (vertical) or more , DataProcessing Up to 14 Bit or more , Contrast 5000:1, Resolution : 2640 X 1485 Pixel, Bonding Wire Copper Wire, Service Access Front, lngress protection lP50, same OEM LED Controller with min. 1 HDMI, 1 DP input ports and OPs Slot, Builtin Operating system, content scaling, 16 LAN Output ports, with Same OEM CMS software. as per site requirements with 5 year Manufacturers warranty. Incluiding Wall Mountig Kit, Patch Cord, Mouting Hardware, License key etc as completed.

Supply, lnstallation, & Testing of Wireless Presentation Devices Compaitible with following functinal features Screen Mirroring Ability to connect to 4 devices simultaneously (MacOS, iOS, Android, Windows), Screen Mirroring presets Multi pre-set for screen mirroring and a mirroring dongle. Control Screen should be operatable via ipad / Android Tablet, Wireless Central Control Host should be able to lock the presentation to one connected device Wireless Source Switching Change the source wirelessly via ipad / Android Tablet, lmage quality effect adjustment, Eye comfort mode incluiding all required accessories, License & Patch Cables

Supply , installation , testing and commissioning of POE enabled AV over IP Transmitter/ Receiver with HDMI input, Local monitor output, 2 Channel Audio Output, Compression technology should be JPEG 2000. Output resolution to be 3840x2160p @30Hz 4:4:4 8bit | @24Hz 4:2:0 HDR 10bit. Acceptable latency should not be more than 1 frame. required licence, patchcable & accessories should be incluided.

Supply , installation , testing and commissioning of POE enabled AV over IP Scalling Transmitter/ Receiver with HDMI input, Local monitor output, 2 Channel Audio Output, Compression technology should be JPEG 2000. Output resolution to be 3840x2160p @30Hz 4:4:4 8bit | @24Hz 4:2:0 HDR 10bit. Acceptable latency should not be more than 1 frame. required licence, patchcable & accessories should be incluided.

Supply, Installation, Testing & Installation of Three Input Multi-Format Switcher with Integrated Long Distance DTP Transmitter and Audio Embedding Transmits DisplayPort, HDMI, or VGA plus control and analog audio up to 330 feet (100 meters) over a shielded CATx cable Auto-switching between inputs Supports computer and video resolutions up to 4K. incluiding all required patch cables, accessories, Mounting Stand & Hardware as completed.

Supplying, installing, testing and commissioning of Customised/ Standard Digital Podium comprised of Metallic house structure, powder coated with caster wheels & brakes. Drawer for keyboard, mouse and document camera. Top with Tranparent Glass with provision to place 22" Interactive Monitor, Wooden Top Tray for placing document & Laptop. All drawers sliding tray and doors should be Lockable. External Passive Connectivity: Having 2 X 3.0 USB, 1 X HDMI 2.0, 1 X C-type, LAN Cable, One MIC XLR with minimum 18" Goosneck microphone, Power Socket with ON/OFF. Provision for 22" Interactive display space. Motorized tilting adjustment for chainging viewing angle. Minimum 6 Universal rating 5 Amp Socket. Provision to fix Logo at the front side. Provision of 19" minimum 12U Rack inside podium to fit in international standerd equipment. Access doors for servicing both from front and back side of the podium. Wire manager on left & right side and at bottom for flexibility of managing additional wire/wiring. all required accessories should be incluided.

Supplying, installing, testing and commissioning of ( FULL HD ) 22”LCD Tablet Monitor with Resolution 1920 x 1080 . View Area 476.64(H) x 268.11(V) ㎜ – 22 inch. Luminance ,White 250 cd/㎡. Colour : 16.7M, Dynamic Contrast Ratio 50,000:1 . Viewing Angle 85˚+85˚H and 80˚+80˚ V. Lamp Life Time 20,000 Hrs (min ). Technology Electromagnetic Resonance. Detectable Height 3~10mm. Position Report Rate 138 pps. Pressure Resolution 1024 Level. CapacitiveTouch Technology:Projected Capacitive. Detected object Fingers, or Conductive material. Tracking speed : 133<-. single :100:Multy:95. Accuracy : +-0.5mm /+-3mm (Edge)3mm wide. Detects height 0-10mm. incluiding all required software, License, stylus, patch cord, mounting Stand etc as completed.

Supplying, installing, testing and commissioning of 49-50" FHD Display panel with features of direct Technology, Lower Power Consumption, Narrow Bezzel, inbuilt speakers Mini.10W, 450 nits brightness, inbuilt memory, Smart WebOS Display with HDMI, RS232 & LAN port & required RJ-45 with standard mounting accessories & Hardware.

Supply, Fixing & Installation of Wall/ Ceiling Mount Fix Stand with tilt vertical -/+10 & Horizontal -/+15 Mechanisam for 32-42" LCD/LED TV

Supply , installation , testing and commissioning of 21" LED Office Monitor, Minimum WXGA (1366x768) resolution, Minimum 250 nits brightness, with HDMI input with standard table mount Stand and required accessories as complete.

Supply , installation , testing and commissioning of AI based Full HD 1080p @ 60fps Presenter PTZ Tracking Camera with Dual Camer one PTZ Camera for Presenter Tracking and second fixed lens Panoramic Camera. PTZ Presenter Camera should support min 20X Optical Zoom and 12x Digital Zoom with Panning range of +170 deg to - 170 deg and Tilt Range of -30 to +90 Degrees, Field of View for PTZ Camera should be min 58 Degree and for Panoramic Camera min. 100 Degree, Camaer should support simultaneous outputs through HDMI, 3G-SDI, USB 3.0 and IP with 1x Audio In and can be controlled via RS232 and IP. Should support multiple video streams. Tracking Camera should support Everywhere Tracking, Partition Tracking, Auto Framing & Gesture Control. Should support PoE and Virtual USB Driver. OEM should be CE, FCC, RoHS & BIS Certified.

Supplying, installing, testing and commissioning of IP camera control with set and save the preset points IP Camera. adjust default positionss, Zoom in/out, movement speed, vertical/mirror and other functions with one click. Support the minimum 450 points (conference unit x 450 + Two HOME + panorama view) and control minimum of 09 ip camera. Intuitive web interface: configure the system settings and control & monitor the camera’s images on the web browser via the PC or mobile devices. Output the IP camera's video at 1920 1080 resolution. Equipped with RJ45 port: connect with Conference MCU to remotely control the camera via Internet and HDMI,RS-232,RS-485 ports. incluiding all required patch cables, accessories, Mounting Stand & Hardware as completed.

Supplying, installing, testing and commissioning of Recording, Streaming & Webcasting Hardware simultaneously, Built-in HDMI, 3G-SDI, IP & USB 3.0 Video Inputs with 1x Line In and 1x XLR Input, 2x HDMI Outputs, Can record upto any two inputs simultaneously in a single frame and as well as individual sources simultaneously. Should have minimum 1TB inbuilt storage and can be connected to local NAS storage. The system should be able to support minimum 3 unicast streams.The recorded files should have the option of time and date stamp. OEM should be CE, FCC & RoHS Certified

Supply , installation , testing and commissioning of USB 3.1 Gen 1 Active Extender Cable. Connector USB Type A (male) to USB Type A (female). Data Rate 10 Gbps. Optical Fiber 850 nm VCSEL (multimode). Cable Diameter 4.5 mm. Supply Voltage 5V ± 0.25V. Flame Retardancy UL13. Compliance FCC-EMI, CE-EMC, RoHS, WEEE

Supply , installation , testing and commissioning of Floor BOX with water proof openable cover. should be accomodate plate 2 Nos. X 6 Module plate with back box. Required mouting accessories and hardware to be considered.

Supply , installation , testing and commissioning of POE enable IP Link Pro Control Processor, 1 LAN Ports, AV LAN port allows AV devices to be isolated from the corporate network, Supports secure industry standard communications protocols, processor with 2 nos of Multi-format Bi-directional serieal Ports RS-232 / RS-422 / RS485, 6 RS232 ports, 8 IR / 1-way serieal ports, 8 Relay, 8 i/0, 2 LAN ports

Supply , installation , testing and commissioning of Web based AV Control server with Hardware support to customizable user interface to control, allows for easy setup, operation, maintenance and management of the system, support to Multi-platform ie. iOS, Android, Macs and PC control. required licence, patchcable & accessories should be incluided.

Supply , installation , testing and commissioning of POE Switch to Provide & manage the power of PTZ cameras, 24 x 10/100/1000 Mbps RJ45 copper ports featuring 30W(max.) power for each POE+ port, offering sufficient power. Complies with IEEE 802.3at POE, end-span PSE. Remote power feeding up to 100M in standard mode.

Supply , installation , testing and commissioning of 4K @30fps UHD Table Stand / Ceiling Mount Document Camera ,Video Output Interface- VGA , HDMI , USB Ethernet, One button optimization function, minimum 20X Optical Zoom & 15x Digital Zoom, should support PoE. Can do annotation without a computer, 2200mm x 1200mm Shooting Area, Internal Memory for minimum 100 JPEG Images. Image rotation 0°, 90° ,180° , 270°,Flip, Mirror. OEM should be BIS, CE,RoHS & FCC Certified

Supply , installation , testing and commissioning of UHD+ 3x2 Matrix Switcher with USB Ethernet Hub, Input Port - 2 x HDMI, 1 x USB-C, Output Port - 2 x HDMI, 1 x Stereo Audio (3.5mm), Bi-directional Port - 2 x RS-232, 1 x RJ-45, Control I/O - 2 x USB 3.0 (Type A) with Service function (USB 1 only) - 1 x USB 3.0 (Type B), HDMI 2.0, HDCP Compliance - 2.X, Input Signal Types 4096x2160p@60 YUV 4:4:4, Output Signal Type 4096x2160p@60 YUV 4:4:4, LPCM 2.0 / 5.1 / 7.1 High Definition Bitstream, Supports auto-switch functionality with a “last memory” feature for both input ports and USB ports, Supports 4K HDR formats by HDR10, HLG and Dolby Vision.

Supply , installation , testing and commissioning of 7feet High Speed and Standard Speed HDMI cables Standard HDMI (M) to HDMI (M) Cable

Supply , installation , testing and commissioning of 15 feet High Speed and Standard Speed HDMI cables Standard HDMI (M) to HDMI (M) Cable

Supply , installation , testing and commissioning of HDMI to Display Port (M) Cable -15 Feet

Supply , installation , testing and commissioning of i-pad for wireless control, Min. 10.5-inch (diagonal) LED-backlit Multi-Touch display, Minimum 2224x1668 resolution at 264 pixels per inch (ppi)l, Retina Display, with Min. 32 GB memory inbuilt. incluiding wall Table mount Charging Dock Station & locking system & required mounting hardware & patch cords

Supply , installation , testing and commissioning of IR Emitter Kits

Supply , installation , testing and commissioning of Wi-Fi access points, Multifunctional wireless APs provide the best 802.11ac Wi-Fi connectivity anduser experience, Dual radio 802.11ac access point with multi-user MIMO- Supports up to the 5 GHz band & 2.4 GHz band with standard ceiling mounting kit

Supply , installation , testing and commissioning of Premium quality LED Blinder Effect Light with latest RDM technology for user friendly operation with below specifications: ● Light Source : Quad LED COB Source • Power Factor : >0.95 @ 230V AC 50Hz • Color Temerature : 3200K, CRI & TLCI Value > 95 • R9 Value > 94 • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 4/8 DMX-512 Channel Modes • Beam Angle : 40° • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • Lux output at 2 Mtr : > 10,000 Lux @ 40° • Flickering Rate : more than 10000 FPS • Dimming: 0 - 100% Electronic Dimming • Power and DMX: Loop in and loop out compulsary • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS Incluiding all required acessories as completed.

Supply , installation , testing and commissioning of Premium quality LED PAR Light with latest RDM technology for user friendly operation with below specifications: • Base Color RGBW Color Mixing • LED Configuration : Multiple Nos Individual RGBW LED Configuartion • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 8 DMX-512 • Beam angle: 15° • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run, Sound Active • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • LUX @ 2m: >10,500 @ 15° Beam Angle • Dimming: 0 - 100% Electronic Dimming • Function: strobe, dimming, sound active and Master slave. • Housing: Die Casted Aluminium or Metal Housing with black epoxy polyster powder coated finish. • Accessory slot for Gel frame and Barndoor should be available or else fixture will be rejected. • Power and DMX: Loop in and loop out compulsary • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS Incluiding all required acessories as completed.

Supply , installation , testing and commissioning of Premium quality LED Profile Spot Light with latest RDM technology for user friendly operation with below specifications: ● Light Source : Single LED COB Source • Power Factor : >0.95 @ 230V AC 50Hz • Color Temerature : 3200K, CRI & TLCI Value > 95 • R9 Value > 94 • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 1/2/3 DMX-512 Channel Modes • Beam Angle : 19° or 15° • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • Lux output at 2 Mtr : > 20,000 Lux @ 19° or 15° • Flickering Rate : more than 10000 FPS • Dimming: 0 - 100% Electronic Dimming • 4 Beam shaping shutters • Accessory slot for Gobo and gobo holder, Iris & Color Frame should be available or else fixture will be rejected. • Housing: Metal Housing with black epoxy polyster powder coated finish or PVC Body with matt black finish • Power and DMX: Loop in and loop out compulsary • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS Incluiding all required acessories as completed.

Supply , installation , testing and commissioning of Premium quality LED PAR Light with latest RDM technology for user friendly operation with below specifications: • Base Color 3200K Color Mixing • LED Configuration : Multiple Nos Individual 3200K LED Configuartion • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 1 DMX-512 • Beam angle: 15° • Control mode: RDM, DMX512 & Manual • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • LUX @ 2m: >7,500 @ 15° Beam Angle • Dimming: 0 - 100% Electronic Dimming • Function: strobe, dimming, sound active and Master slave. • Housing: Die Casted Aluminium or Metal Housing with black epoxy polyster powder coated finish. • Accessory slot for Gel frame and Barndoor should be available or else fixture will be rejected. • Power and DMX: Loop in and loop out compulsary • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS Incluiding all required acessories as completed.

Supply , installation , testing and commissioning of Premium quality LED Cyclorama Wash Light with latest RDM technology for user friendly operation with below specifications: • Base Color RGBWA 5 in1 Color Mixing • LED Configuration : Multiple Nos Individual RGBWA 5 in 1 LED Configuartion • Power cable: 3 core 1 sq. mm. copper PVC insulated • Channels: 8 DMX-512 • Beam angle: 30° or 45° • Control mode: RDM, DMX512 & Manual, Master/Slave, Auto run, Sound Active • Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project. • LUX @ 2m: >2,700 @ 30° Beam Angle • Dimming: 0 - 100% Electronic Dimming • Function: strobe, dimming, sound active and Master slave. • Housing: Die Casted Aluminium or Metal Housing with black epoxy polyster powder coated finish. • Power and DMX: Loop in and loop out compulsary • DMX in & Out Through : 5 Pin XLR connectors • Certification: CE / BIS Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply & installation of Die cast Aluminium C - Clamp with safety chain duly epoxy polyester powder coated in black matt texture finish and safe working load of 100kg with below specifications. • Lock - MS threaded Galvanized lock key, • Plastic Glass filled nylon moulded M6 key. • Receptacle - 28mm standard TV spigot. • Safety - MS Galvanized chain with pin. • Finish - Pretreated and black epoxy polyester powder coated. • Self-weight - 0.54Kg Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation of Safety bond with lock clip 1.5 Mtr Long made with twisted pair of GI wire rope, 2mm or 3mm Thickness with sleeve to be fixed around the grid to avoid fall of the material in case if the "C" clamp is not locked properly. SWL 150Kgs. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply & installation of 79mm Round Identification name plate duly epoxy polyester powder coated in matt texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply & installation of Fixed Stage Light Bar, length 10 Mtrs made using MS 40NB Class ‘B’ Pipe dual barrel construction arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications: • Dual barrel Light bar equipped with 40x75x40 Cable trenching arrangement with lid for better aesthetic look and cable safety. • Dual barrel pipe construction welded with 75x6mm MS Flat in every 1 Mtr for better strength • With Suitable Suspenders to fix the light bar with every 2mtr pitch. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply & installation of Front of house Light Bar, length 11 Mtrs made using MS 40NB Class ‘B’ Pipe dual barrel construction arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications: • Dual barrel Light bar equipped with 40x75x40 Cable trenching arrangement with lid for better aesthetic look and cable safety. • Dual barrel pipe construction welded with 75x6mm MS Flat in every 1 Mtr for better strength • With Suitable Suspenders to fix the light bar with every 2mtr pitch. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation, testing and commissioning of Main Curtain track system 16 Mtrs long, center parting with overlap of 0.9mtr arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications: • Heavy duty curtain track duly epoxy polyester powder coated in black matt texture finish. • 1.0 HP Motor, 3 Phase Motor. • GI wire ropes with steel core at center. • Curtain holding trollies placed uniformly at specific interval of 200mm /250 mm throughout the track. • Diverter pulley • MS yellow passivized Routing pulleys with ball bearing for smoother noiseless movement 165mm for outer diameter, 145mm diameter at groove base with 12mm pulley thickness. • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of Rear Curtain track system 11.0 Mtrs long, center parting with overlap of 0.9mtr arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications: • Heavy duty curtain track duly epoxy polyester powder coated in black matt texture finish. • 1.0 HP Motor, 3 Phase Motor. • GI wire ropes with steel core at center. • Curtain holding trollies placed uniformly at specific interval of 200mm /250 mm throughout the track. • Diverter pulley • MS yellow passivized Routing pulleys with ball bearing for smoother noiseless movement 165mm for outer diameter, 145mm diameter at groove base with 12mm pulley thickness. • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of Valance Bar, length 16 Mtrs made using 40NB, 48mm OD construction arrangement 2mm Thickness undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with suitable suspenders. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of Fixed Frill Bar, length 10 Mtrs made using 40NB, 48mm OD construction arrangement 2mm Thickness undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with suitable suspenders. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of MS, Wing frame made out of 25mm or higher size of MS square pipe with 2mm in thickness undergone through various chemical treatment to keep them rust free and duly powder coated in black matt texture finish with Below Specifications: • Wing Frame Size 1.5 x 4.5 Mtr • 1.5meter wing track of 48x84mm with grid mount brackets made of 40X50X40mm C track, • Pivotable 4 wheeled suspension trolley, • Adjustable floor locking screw jacks with rubber grips, • Inverted 4-Wheeler Trolley with Flexi Adaptor Clamp, • Heavy duty wing track to be laid for minimum length of 1.5mtr, along the width of the stage. • 360° Rotatable and can move in unidirectional • All the materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of Cyclorama frame arrangement of size 9.0 x 4.5 Mtr undergone through various chemical treatment to keep them rust free and duly powder coated in black matt texture finish with Below Specifications: • Heavy duty Cyclorama track duly epoxy polyester powder coated in black matt texture finish to use as straight cyclorama track • MS fabricated Grid/wall mount bracket constructed of C track of dimension 40X50X40mm duly powder coated to hold the Cyclorama track, • MS fabricated Tie down railing cut length 3 mtr duly powder coated to keep the cyclorama in drum tight arrangement, • 2 wheeler trolley placed uniformly at specific interval of 200mm/250mm throughout the track to hold the cyclorama screen • MS powder coated Leading edge pipe of 25NB, 33.4MM OD, 2mm thickness to keep the cyclorama in drum tight arrangement. • All the MS materials under gone through 7 tank process with various chemical treatment to keep them rust free with and duly epoxy polyester powder coated in black matt texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of MS Fabricated 4 way 10A, 250V A.C, IEC, Lighting Junction box made up of 22SWG CRCA for LED lighting fixtures with Pipe clamp arrangement for fixing on pipe grid or Raul plug arrangement for wall/floor fixing, duly black epoxy polyester powder coated texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of MS Fabricated 2 way 10A, 250V A.C, IEC, Junction box made up of 22SWG CRCA with rocker switch to power up splitter and console with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, duly black epoxy polyester powder coated texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of MS Fabricated 5 pin DMX Signal IN Junction box fitted with 5 pin DMX Male socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of MS Fabricated 5 pin DMX Signal OUT Junction box fitted with 5 pin DMX female socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of Fabricated 5 pin DMX Signal loop Junction box fitted with 5 pin DMX Male & Female socket with 0.3 Mtr DMX Loop cable fitted with 5 pin DMX cable mount plug, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement for fixing or Raul plug arrangement for wall/floor fixing, black epoxy polyester powder coated, duly black epoxy polyester powder coated texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of Well designed 21 Way Direct Lighting Distribution Board made up of CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt texture finish consists of R, Y, B Indicator lamp, 50A TPN incomer, SP Mcb's and for the junction boxes fixed on the top of the light bar including wiring and busbar connection with proper earthing and Hingable door with magnetic door lock complete. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of Auxiliary marshalling box for power and signal cable termination in grid level and in Motorised Light bar • CE Marked FC/PG cable entry gland required Nos as per cable entry. • MS channel arranging to fix terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. • Grey terminal connector with each line having P, N, E Indication for each line incoming and out going cable connectors. • Box door must be made with Hingeable door with screw lock. • Made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of Motor Cable Termination box for power cable termination at grid level. incluiding all required hardware & accessories as completed. • CE certified FC/PG 11 & 13.5 cable entry gland required Nos as per cable entry. • MS channel arranging to fix grey terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap. • Grey terminal connector with each line having L1, L2, L3, E, 6 , 2 , 4 Indication for each line incoming and outgoing cable connectors (L1, L2, L3, E for Power supply & 6 , 2 , 4 for Limit Switch connection) • Box door must be made with Hingeable door with screw lock. • Grid mount fixing arrangement for fixing on grid or Anchor fastener for wall/floor fixing • MS Boxe made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of RDM Compatible DMX Splitter unit with Minimum following specifications. ● 1 Nos 5 Pin DMX In socket and 8 Nos 5 Pin DMX Out socket ● In and out signal Optically Isolated ● LED Indicator for check the signal flow in output. ●Suitable for standard 19” cabinet ● Duly black epoxy polyester powder coated texture finish. Incluiding all required hardwaare, Accessories & Mounting Hardware as completed.

Supply , installation , testing and commissioning of Digital Lighting console with Minimum following specifications. ● 512 Channel, 2 Output ● No. Of Direct Fixture Control : Atleast 200 or more ● No. Of Faders : Atleast 12 ● Atleast 4 Encoder Wheels ● 7" Touch screen display for navigation ● Backlight Keyboard ● Numeric Key Board Incluiding all required patch cables, Mounting Hardware and required accessories and License.

Supply , installation , testing and commissioning of 5 pin XLR male / female connectors of made up of Extra high temperature resistant insulator material, Larger solder contacts for easier termination.

Supply , installation , testing and commissioning of 5 Pin XLR Termination plug made up of extra high temperature resistant insulator material, Larger solder contacts for easier termination with 120 Ohm resister with 0.25Watt for signal termination.

Supply , installation , testing and commissioning of Main Curtain Fabric : Fire retardant velvette fabric with lining 100% (2 times of the finished dimension) gathering as per the approved patern and colour, not less than 300 GSM, duly stitched along with eyelets. Size : 17 x 4.5 Meter

Supply , installation , testing and commissioning of Rear Curtain Fabric : Fire retardant cotton fabric 50% gathering for as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 12 x 4.5 Meter.

Supply , installation , testing and commissioning of Main Valance Fabric : Fire retardant velvette fabric 100% (2 times of the finished dimension) gathering as per the approved patern and colour, not less than 300 GSM, duly stitched along with eyelets. Size :16 x 1.2 Meter

Supply , installation , testing and commissioning of Frill Fabric : Fire retardant cotton fabric 50% gathering for as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size :10 x 1.2 Meter (Average).

Supply , installation , testing and commissioning of Wing Fabric : Fire retardant cotton fabric 0% gathering for as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 3.1 x 4.5 Meter .

Supply , installation , testing and commissioning of Cyclorama : Perforated plastic Cyclorama screen with zero gain, off white, with eyelets along all four sides, perforated plastic screen with eyelets. Size : 9.0x 4.5 Meter.

Supply , installation , testing and commissioning of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 7cx1.5 sq mm.

Supply , installation , testing and commissioning of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 4c x 4 sq mm.

Supply , installation , testing and commissioning of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 3cx1.5 sq mm.

Supply , installation , testing and commissioning of DMX Signal 2 core + Ground shielding Cable for the Signal network.

Supply , installation , testing and commissioning of MS perforated tray of Size 40 x 75 x 40mm & 1.6 mm Thickness undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish along with clamping arrangement.

Supply , installation , testing and commissioning of Internal earthing copper bare conductor of size 14 SWG for power network related to work coming under our scope.

Supply , installation , testing and commissioning of Installation hardware’s such as clamps, connectors, glands, lugs, ferrules, welding rods and miscellaneous items required during installation work.

Supply , installation , testing and commissioning of HDMI Splitter 1:4 Splitter Highspeed with Ethernet VER 2.0, 3D, ARC+HEC, 4K with standard required hardware, accessories & Patch Cables.

AV SYSTEM FOR ADMN BLDG CONF RM (GRND & 4TH FL) & TRANSIT BLDG -6TH FL.

Supplying, installing, testing and commissioning of "98-100" 4K Resolution (UHD) Display panel with features of direct Technology, Minimum 490 nits brightness Energy Efficient, Multi-Touch, Narrow Bezzel, Anti-Glare Tempered Glass, Screen Mirroring, OTA, Enhanced Security, inbuilt speakers, inbuilt memory, Wifi Dongle with HDMI Out ( RGB, Android, OPS) , RS232 & LAN port & required RJ-45. Proposed product should be certfied with BIS, RoHS, Energy Star,, FCC Class "A" / CE, ERP . Prices should be incluiding all required standard mounting accessories (Wall bracket), license & Hardware as complete.

Supply, lnstallation, Testing & installation of Wireless Presentation Devices Compaitible with following functinal features Screen Mirroring Ability to connect to 4 devices simultaneously (MacOS, iOS, Android, Windows), Screen Mirroring presets Multi pre-set for screen mirroring and a mirroring dongle. Control Screen should be operatable via ipad / Android Tablet, Wireless Central Control Host should be able to lock the presentation to one connected device Wireless Source Switching Change the source wirelessly via ipad / Android Tablet, lmage quality effect adjustment, Eye comfort mode, lmage quality effect adjustment. incluiding all required accessories, License & Patch Cables

Supplying, installing, testing and commissioning of Full HD 1080p @ 60 frames per second PTZ Camera with minimum 20X Optical Zoom and FoV of minimum 57 deg, min 100 Presets.Camera should support simultaneous outputs through Ethernet, HDMI, 3G-SDI, Audio In and can be controlled via RS232 & 422 In & Out & IP.Panning angle -170° ~ +170°, Tilting angle -30° ~ +90° . The tilting and panning speed of camera should be minimum 300° per second. Camera should support SRT, FreeD Protocol, PoE and Virtual USB Driver and should be NDI compatible. OEM should be CE, FCC, RoHS & BIS Certified. Incluiding all required Wall Mounting Kit, necessary hardware, Patch Cables, License & Software etc.

Supply, Instalaltion, Testing & Commissioning of Table Mount Cable Cubby box TYPE-1 with , 1XUSB, 1X C-TYPE, 2 X RJ-45 Port & 2 X 5A Power Points with mounting Hardware.

Supply, Instalaltion, Testing & Commissioning of Table Mount Cable Cubby box TYPE-1 with , 1X HDMI+A, 1XUSB, 1X DP, 2 X RJ-45 Port & 2 X 5A Power Points with mounting Hardware.

Supply , installation , testing and commissioning of POE enabled AV over IP Transmitter/ Receiver with HDMI input, Local monitor output, 2 Channel Audio Output, Compression technology should be JPEG 2000. Output resolution to be 3840x2160p @30Hz 4:4:4 8bit | @24Hz 4:2:0 HDR 10bit. Acceptable latency should not be more than 1 frame. required licence, patchcable & accessories should be incluided.

Supply , installation , testing and commissioning of POE enabled AV over IP Scalling Transmitter/ Receiver with HDMI input, Local monitor output, 2 Channel Audio Output, Compression technology should be JPEG 2000. Output resolution to be 3840x2160p @30Hz 4:4:4 8bit | @24Hz 4:2:0 HDR 10bit. Acceptable latency should not be more than 1 frame. required licence, patchcable & accessories should be incluided.

Supply , installation , testing and commissioning of POE enable IP Link Pro Control Processor, 1 LAN Ports, AV LAN port allows AV devices to be isolated from the corporate network, Supports secure industry standard communications protocols, processor with 2 nos of Multi-format Bi-directional serieal Ports RS-232 / RS-422 / RS485, 6 RS232 ports, 8 IR / 1-way serieal ports, 8 Relay, 8 i/0, 2 LAN ports

Supply , installation , testing and commissioning of compact Switcher with dual input for manually or automatically switching a connected HDMI or VGA + audio source to a single HDMI output, CEC-Link Compatible. Required software, accessories & Table Mount accessories shall be incluided as complete.

Supply , installation , testing and commissioning of 7feet High Speed and Standard Speed HDMI cables Standard HDMI (M) to HDMI (M) Cable

Supply , installation , testing and commissioning of 15 feet High Speed and Standard Speed HDMI cables Standard HDMI (M) to HDMI (M) Cable

Supply , installation , testing and commissioning of HDMI to Display Port (M) Cable -15 Feet

Supply, Instalaltion, Testing & Commissioning of 240W Dual Zone Mixer Amplifier with 2 line inputs , 2 line Output & COM /RS484/LAN Port. Inclusive of all standard mouting patching and fixing accessories.

Supply, Installation, Testing & Commissioing of Ceiling mount speaker with frequency respose of 95Hz - 17kHz; nominal dispersion of 140 degree conical; Power handling 16W @ 8 Ohms, Transformer tapping (70/100V) : 1W, 2W, 4W, 8W, 16W), sensitivity 84 db SPL; and Max SPL of 96 db SPL with powder coated steel grille as per the tender specifications.

Supply, Instalaltion, Testing & Commissioning of central Control unit should have control minimum 9 chairman units & 90 delegate units by extension power supply. System should have to facility to control upto 14 or more cameras for look at me feature . It should have 128x64pixels digit LCD monitor display for configurations. The system should have auto testing facility when powered on. Support voting and GUI feature. Technical specification:- Frequency response : 50HZ~16KHZ( ±1dBV ) T.H.D. ： ≦0.1% S/N Ratio ： ≧85dBV AUX out: RCA jack balanced and AUX 1 input (RCA). 4 individual outputs specially for microphone units USB port (type A): Soft VC TCP / IP protocol control via wired or wireless network using a PC or mobile device. RS-232 , RS 485 port (D+, D --)and LAN Port for programming and controlling Conference microphone connection： CAT5E cable RJ-45 port x 4 sets Ethernet Technology: 10 MBPS Ethernet. OEM should be CE and FCC, Certified . All standard mounting patch cord accessories , hardware & software ( microphone managment, synoptic layout software and Voting Software). .

Supply, Instalaltion, Testing & Commissioning of Flush Mount Delegate Unit should have a built-in DSP chip which can adjust the audio output and sensitivity automatically and support Cat5E/6 cabling in easy to mantain and flexible way through daisy-chain, ring, tree or star modes and with push to talk and speak button, pluggable gooseneck microphone easy to remove when not in use and with light ring for easy identification of the speaker. Pluggable gooseneck microphone Stem length: 48/56/70 cm . Microphone should get auto off when not in use and also get auto activated when someone starts to speak. Technical Specification:- Frequency response :100HZ~16KHZ Sensitivity : ≧-50dB S/N ratio : ≧70dB Auto Gain Control (AGC) -45 ～ 0dB Connections RJ-45 Jack x 2 Earphone jack 3.5Ø Stereo REC jack 3.5Ø Stereo. All standard mounting patching & fixing accessories and software incluiding digital interface module.

Supply, Instalaltion, Testing & Commissioning of Flush Mount Chairman Unit should have a built-in DSP chip which can adjust the audio output and sensitivity automatically and support Cat5E/6 cabling in easy to maintain and flexible way through daisy-chain, ring, tree or star modes and with push to talk and priority speak button, pluggable gooseneck microphone easy to remove when not in use and with light ring for easy identification of the speaker. Pluggable gooseneck microphone Stem length: 48/56/70 cm . Microphone should get auto off when not in use and also get auto activated when someone starts to speak. Technical Specification:- Frequency response : 100HZ~16KHZ Sensitivity : ≧-50dB S/N ratio : ≧70dB Auto Gain Control (AGC) -45 0dB Connections RJ-45 Jack x 2 Earphone jack 3.5Ø Stereo REC jack 3.5Ø Stereo. All standard mounting patching & fixing accessories and software.

Supply, Instalaltion, Testing & Commissioning of 8 X 8 Digital Audio Matrix Processor: ADI SHARC 21489@450 MHz SIMD. DSP capability:400 MIPS; 1.6 GFLOPS. Applied with the software for managing the operation of all audio channels. Supports adaptive echo cancellation (AEC): 60dB/S convergence rate; 80dB echo cancellation level. Built-in automatic noise suppression (ANS): making the SNR increase 18db. Supports adaptive feedback control (AFC), automatic gain control (AGC): auto-gain control -6dB~+18dB; auto-balance control -12dB~+12dB. Support ducker, ANC, AM, and Gate Mixer. Definable UI for managing and configurating the max. of 30 units. Centralized control: easily one click to control the power of A/V equipment and switch the audio source. USB audio for soft Audio conferencing. required accessories to be incluided.

Supply , installation , testing and commissioning of POEe Switch to Provide & manage the power of PTZ cameras, AV over IP Devices. switch shall have 8 sets of 10/100/1000 Mbps RJ45 copper ports featuring 30W(max.) power for each POE port, offering sufficient power. Complies with IEEE 802.3at POE, end-span PSE. Remote power feeding up to 100M in standard mode.

Supply , installation , testing and commissioning of i-pad for wireless control, Min. 10.5-inch (diagonal) LED-backlit Multi-Touch display, Minimum 2224x1668 resolution at 264 pixels per inch (ppi)l, Retina Display, with Min. 32 GB memory inbuilt. incluiding wall Table mount Charging Dock Station & locking system & required mounting hardware & patch cords

Supply , installation , testing and commissioning of minimum 8 Channel Relay for Curtain control, High votage relay controller with 8 up/down relays, with RS232 control

Supply , installation , testing and commissioning of minimum 8 button Wall Mount Keypad with back box and standared mouting accessories as complete.

Supply and laying of 2 core 1.5 sq mm PVC insulated Cu conduction speaker cable as per the tender specifications.

Supply and laying of USB- USB 6 Meter Patch Cord as per Specifications.

Supply and laying of USB- USB 12 Meter Patch Cord as per Specifications.

Supply & fixing of 18U Wall/ Floor-mounting cabinets. size around 600X500mm (WXD) with all standard accessories. Width (mm) 800, Depth (mm) - 800, CRCA 'D' Grade thickness (mm) - 1.2, RAL 9017 (Matt Black), Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Earthling Strips 150mm H - 1 No, Wall Screws (4 sets of 2'' screws, washer, rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained1 U = 1.75 inches space.

AUDIO-VIDEO SYSTEM FOR CLASS ROOM

Supply, Instalaltion, Testing & Commissioning of Supply of Panel Size 86" Interactive display with Type/Tech TFT LCD Module with DLED Backlight, VA. diagonal. Aspect Ratio 16:9. Native Resolution UHD 3840x2160(Pixels). Embedded OS: Android 9. Bundle Software:, Colors 1.07B colors (10bit). Brightness 350 nits (typ.). Contrast Ratio 1200:1 Typ. / 4000:1 Max.(DCR enable). Response Time 6.5ms. Viewing Angles H = 178, V = 178 typ. Backlight Life 30,000 Hours (Min). Surface Treatment Anti-Glare, Haze 25%，Hard Coating(3H) Protection glass: G1S, AG glass, 9H(pencil). Touch glass thickness 4mm. Haze 25%. Bezel ( L/R/T/B) 15.6/15.6/15.6/43.5 mm. Orientation Landscape. Platform : Processor ARM quad-core Cortex-A55, 12nm. RAM 4GB DDR4. Storage 32GB. Touch: Type/ Tech IR Recognition. Touch Resolution 32768×32768. Touch Point 20. Point of writing 2. Response Time ≤10ms. Scan rate 100HZ. Accuracy size 90% area +/- 2mm . Pen tips size 3mm. INPUT : HDMI-IN 2.0 x2 (3840x2160 @60Hz) (HDMI 2 port support ARC function). RGB / VGA x1. Audio x1 (PC audio in). RS232 x1. OPS x1 OPS 80pin. OUTPUT: Audio x1 (Earphone out). LAN : RJ45 x1. USB : Type A USB2.0 Front*2, smart port Rear*2, one for camera. SPEAKERS: 10W x 2. Camera plate on top for srew-in webcam installation, All requied Hardware, software, license & patch cord should be incluided.

Supply, Instalaltion, Testing & Commissioning of Supply of Panel Size 75" Interactive display with Type/Tech TFT LCD Module with DLED Backlight, VA. diagonal. Aspect Ratio 16:9. Native Resolution UHD 3840x2160(Pixels). Embedded OS: Android 9. Bundle Software:, Colors 1.07B colors (10bit). Brightness 350 nits (typ.). Contrast Ratio 1200:1 Typ. / 4000:1 Max.(DCR enable). Response Time 6.5ms. Viewing Angles H = 178, V = 178 typ. Backlight Life 30,000 Hours (Min). Surface Treatment Anti-Glare, Haze 25%，Hard Coating(3H) Protection glass: G1S, AG glass, 9H(pencil). Touch glass thickness 4mm. Haze 25%. Bezel ( L/R/T/B) 15.6/15.6/15.6/43.5 mm. Orientation Landscape. Platform : Processor ARM quad-core Cortex-A55, 12nm. RAM 4GB DDR4. Storage 32GB. Touch: Type/ Tech IR Recognition. Touch Resolution 32768×32768. Touch Point 20. Point of writing 2. Response Time ≤10ms. Scan rate 100HZ. Accuracy size 90% area +/- 2mm . Pen tips size 3mm. INPUT : HDMI-IN 2.0 x2 (3840x2160 @60Hz) (HDMI 2 port support ARC function). RGB / VGA x1. Audio x1 (PC audio in). RS232 x1. OPS x1 OPS 80pin. OUTPUT: Audio x1 (Earphone out). LAN : RJ45 x1. USB : Type A USB2.0 Front*2, smart port Rear*2, one for camera. SPEAKERS: 10W x 2. Camera plate on top for srew-in webcam installation, All requied Hardware, software, license & patch cord should be incluided.

Supply, Instalaltion, Testing & Commissioning of Table / Wall Mount Plate with 1X HDMI, 1XVGA, 1XUSB, 2 X RJ-45 Port. 2 X USB, 1 X C-Type, & 2 X 5 AMP PWR. Points with required size of backbox and mounting Hardware.

Supply , installation , testing and commissioning of 15 feet High Speed and Standard Speed HDMI cables Standard HDMI (M) to HDMI (M) Cable

Supply , installation , testing and commissioning of HDMI to Display Port (M) Cable -15 Feet

Supply , installation , testing and commissioning of USB to USB Port (M) Cable -15 Feet

Supply, Instalaltion, Testing & Commissioning of 120W Mixer Amplifier with 2 X Mic / Line Input. Incluiding all standard mouting patching and fixing accessories.

Supply, Installation, Testing & Commissioing of 20W Wall Mount mount speaker with frequency respose of 95Hz - 17kHz; nominal dispersion of 140 degree conical; Power handling 16W @ 8 Ohms, Transformer tapping (70/100V) : 1W, 2W, 4W, 8W, 16W), sensitivity 84 db SPL; and Max SPL of 96 db SPL with powder coated steel grille as per the tender specifications.

Supply, installation, testing & Comissioning of wireless head worn microphone with omnidirectional polar pattern,condenser microphone ,frequency response 50Hz-20kHz,RF sensitivity < 2.0 Uv,Image rejection>100dB, Dynamic range >120dB and receiver having 12 channels possible, S/N ratio >120dBA, dynamic range >120db B, distortion <1 %,frequency band:648-676MHz, modulation:+/-40kHz; Incluiding all required accessories as completed.

Supply and laying of 2 core 1.5 sq mm PVC insulated Cu conduction speaker cable as per the tender specifications.

ROOM DISPLAY

Supplying, installing, testing and commissioning of 21"- 25" FHD Display panel with features of direct Technology, Lower Power Consumption, Narrow Bezzel, 450 nits brightness, inbuilt memory, Smart WebOS Display with HDMI, RS232 & LAN port & required RJ-45 with standard mounting accessories & Hardware.

Supplying, installing, testing and commissioning of 46"- 49" FHD Display panel with features of direct Technology, Lower Power Consumption, Narrow Bezzel, inbuilt speakers Mini.10W, 450 nits brightness, inbuilt memory, Smart WebOS Display with HDMI, RS232 & LAN port & required RJ-45 with standard mounting accessories & Hardware.

Supplying, installing, testing and commissioning of 52"- 55" FHD Display panel with features of direct Technology, Lower Power Consumption, Narrow Bezzel, inbuilt speakers Mini.10W, 450 nits brightness, inbuilt memory, Smart WebOS Display with HDMI, RS232 & LAN port & required RJ-45 with standard mounting accessories & Hardware.

Supplying, installing, testing and commissioning of 60"- 65" FHD Display panel with features of direct Technology, Lower Power Consumption, Narrow Bezzel, inbuilt speakers Mini.10W, 450 nits brightness, inbuilt memory, inbuilt Speaker, Smart WebOS Display with HDMI, RS232 & LAN port & required RJ-45 with standard mounting accessories & Hardware.

Supplying, installing, testing and commissioning of 48"- 50" hospitality Guest Room UHD Display panel with features of direct Technology, Lower Power Consumption, Narrow Bezzel, inbuilt speakers Mini.10W, 300 nits brightness, inbuilt memory, Inbuilt 10+10W Speaker, Smart WebOS Display with HDMI, RS232 & LAN port with standard mounting accessories, Remote & Hardware.

Supplying, installing, testing and commissioning of Wall Mount Fix Stand with tilt vertical -/+10 & Horizontal -/+15 Mechanisam for 32-65" LCD/LED Display

SUB HEAD XLIV : BUILDING MANAGEMENT SYSTEM

Supply, Installation, Testing & Commissioing of UL Listed BMS System Software : Graphical Software meeting the requirements in the Given I/O Summary with state of the art UI with Navigation window primary pane secondary pane and operation area, Seamless Integration with Fire Alarm, CCTV & Access Control System, 3D Vector Graphics , Supporting Assistive treatment, Investigative treatment, Event Logging, Report Scheduling, configuration and facility to animate the Graphics, Navigation between pages, display of logs, changing the time zones, popup alarms, configurable password protection for Building Mgmt System as per Specifications. Software shall be able to communicate with Lonworks, Bacnet, SNMP, OPC & Modbus devices simultaneously, with minimum 2 users.

Supply, installation, testing & commissioning of Central Server with the minimum following specifications,: Intel® Xeon® processor E3, 3.2GHz, 4 Core, 8MB Cache memory, Intel HD Graphics , 1TB HDD, 8 GB Ram, Rack Mount Server with Database, OS & loaded with lifetime license. The server shall have 2 X 1000 Mbps Ethernet port for browsing and configuring BMS Software .

Supply, installation , testing & commissioning of Workstation with minimum:i5 4 core, 2.2GHz, 1 TB HDD, 4GB RAM, 52X CD Writer Drive, along with keyboard, mouse) etc, Cost should be With Life time license for Windows 8 enterprise/ professional or latest software compatible MacAfee /Symantec Anti virus & All other related software such MS office with liscesenced.

Supply, Installation, Testing & commissioning of full HD professional display for 24/7 monitoring, display size shall not be less than 46"with HDMI, PC inputs. Incluisive of required mounting hardware & accessories as completed

Supply, installation, Testing & Commissioning of 24 inch TFT/LED Monitor. Incluisive of required mounting hardware & accessories as completed.

Supply, Installation, Testing & Commissioing of A4 Size Leser Jet Printer with required software, hardware & Accessories.

Supply Installation, Testing & Commissioning of Onboard IP-based Direct Digital Controllers with maximum 32 IO Points with LED indicators, a 32-bit microcontroller and minimum 400Mhz processor, and a Real-time Clock. It shall have inbuilt support for BACnet IP & MSTP as well as Bacnet Client and Server in the same controller and be capable of stand-alone operation; i.e. in the event of loss of communication, it shall be able to function on its own. inclusive of Enclosure MS Powder Coated cabinet, license, hardware & accessories as complete with all internal wiring

DDC for Air Handling Unit

DDC for PAC Unit

DDC for Electrical System - Substation

DDC for Electrical System - breaker

DDC for Diesel Generator

Supply, installation, integration, Testing & Commissioning of Middleware & Integrators for Soft Points. Open Protocol Output Integrators compatible for BACNET/MODBUS IP output meeting Vendor's communication platform to Acquire data and Control Operation of following Equipment / Hardwares complete with required license, enclosure duly internally wired, Mouting accessories and tested OEM supplied UL Listed

PAC Unit

VRV/ VRF Unit

Enargy Meter / Load Manager

Transformer

FAS. VESDA, Fire Suppression, WLD & PA System

Fire Fighting System

Supply Installation, Testing & Commissioning of the below sensors with required mouting kits, patch cables, hardware & accessories as completed

Indoor Air Temperature & Humidity Sensor

Air DP Switch

Duct Temp Sensor

Outside Air Temperature & Humidity Sensor

Static Pressure sensor

Flame Proof 4 Level Transmitter

Supply & laying of Cabling for instrument, controls to DDCs and communication cabling from DDC to central equipment complete with earthing, supports etc complete. All Cables shall be ferruled and tagged, and shall use lugs for termination at both ends.

2 Core x 1 sq mm FRLS Screened with drain wire, Armoured Cable for control cabling

4 Core x 1 sq mm FRLS Screened with drain wire, Armoured Cable for control cabling

Armoured, Cat-6 cable, laid on Surface with GI Saddle- Spacers , or in cable trays, as per site requirements, with required terminations as required with Cable tie`s & Tags.

Supply & Installation of Hot dipped galvanized perforated Cable Tray of below Sizes complete with necessary coupler plates, hardware & required accessoreis in approved manner .

200 X 50mm Perforated Cable Tray

300 X 50mm Perforated Cable Tray

SUB HEAD XLV: WATER LEAK DETECTION SYSTEM

Supply, Installation, Testing and Commissioning of Water Leak Detection System with standard required panel, module, Cables, mouting Plate with back box, hardware, accessories & Connector as completed. System shall capable to identify the type of alarm leak / break/short/probe as the location. shall be able to monitor (Detect & locate) with up to 100 feet of cable wetted without significant inaccuracy in location and capable to moinitoring up to 2000 feet of cable per sensor string from a single monitoring unit.

Water Leak detection panel with keypad & 4 Line by 20 Character backlit LCD Display unit. Panel shall have RS-485 Port and two serial communication Ports for monitroing and control from Remote Location. The Monitoring unit shall be enclosed in a Type 12 (IP65) enclosure. CE Certfified. (For 25Sq Meter Area )

Central Monitoring Software with cusomizable GUI for monitoring & control for multiple location. Software shall have password security for varying level of system access. Incluiding software, license and accessories as completed.

The water sensing cable shall be resistant to corrosion. It shall detect the presence of Water as well as slightly corrosive & conductive fluids. The cable shall be constructed of total four wires (two sensing wires and 1 no of Continuity wire & 1 no. of return insulated wires. The cable shall be constructed with no metal parts exposed to the environment.

End of the Line (ZIM)

Start of the Line (ZIM)

Fixing Clip ( 1/mtr.)

Identification tags (1/3 Mt.)

Sounder (40 - 65 db)

Water leak modules

2C x 1.5 sq.mm FRLS Armoured cable (Colour – Blue)

SUB HEAD XLVI: GAS SUPPRESSION SYSTEM

Supply, installation, Testing & Commissioning of Gas Suppression System for Telecom Equipment Room as per NFPA 2001 Specification considering Extinguishing Concentration and a minimum design concentration as per applicable to Class "A" Risks. inlcuiding with required all necessary Modules, Timer Cards, Hardware & Mounting Accessories. Note: Contractor has to submit Calculation wtih Consultant / Client for approval before execution.

Supply, Installation, Testing & Commissioning of Seamless Cylinderes of 80KG with Valve assembly, pressure Gauage Protection CAP approved by CCOE incluiding Tank mounting bracket assembly as completed.

Supply, Filling & Testing of NOVEC 1230 gas in KG. (Contractor to submit Certificate of proposed Gas along with Calculation)

Supply, Installation, Testing & Commissioning of Electromagnetic Actuator

Supply, Installation, Testing & Commissioning of Manual Actuator

Supply, Installation, Testing & Commissioning of Pneumatic actuator

Supply, Installation, Testing & Commissioning of Discharge Nozzles

Supply, Installation, Testing & Commissioning of Flexible Discharge Hose

Supply, Installation, Testing & Commissioning of Non-Return Valve

Supply, Installation, Testing & Commissioning of Pilot Hose

Supply, Installation, Testing & Commissioning of Container Strap

Supply, Installation, Testing & Commissioning of Low Pressure Supervisory Switch

Supply, Installation, Testing & Commissioning of Gas Release Panel with Independent Battery Back up (for 4 Hours ) including Timer Cards

Supply, Installation, Testing & Commissioning of Timers Cards

Supply, Installation, Testing & Commissioning of Manual Overide Switches ( Green Color) of ABS Plastic.

Supply, Installation, Testing & Commissioning of Manual GAS Release Switches (Yellow Color) of ABS Plastic

Supply, Installation, Testing & Commissioning of M.S. Seamless pipes as per ASTM A 106 Gr. B, schedule 40 with necessary fittings. ( 20 Sq. Meter Rm.)

Supply & Installation of Manifold for Cylinders Warning Signs with Backlit Illumination ( Illumination to be in case of GAS Release). Sings board shall be as below :

Supply & Fixing of NOVEC 1230 GAS RELEASED VACATE IMMEDIATELY

Supply & Fixing of ROOM PROTECTED BY NOVEC 1230 GAS

Supply & Fixing of GAS DISCHARGED DO NOT ENTER

Supply, Laying & Testing of 2C X 1.5 SQ.MM FRLS Aarmoured Cable (RED Color)

SUB HEAD XLVII: EARLY SMOKE DETECTION SYSTEM

Supply, Installation, Testing and Commissioing of VESDA system incluiding required software, license, hardware, associated cables & mouting accessories as completed

Aspiration Tubes with supporting for Pipe @ 1 Meter Interval. Required accessories, bends, couplers & hardware shall be inlcuided.

Capillary Tubes

Air Termination Nozzles

Electronic Hooter

2C x 1.5 Sq.mm Cu. Armored Cable for connecting hooters

SUB HEAD XLVIII : HOSPITALITY MANAGEMNT SYSTEM

Supply, Installation, Testing and Commissioing of Hospitality Management Software incluiding required, license, hardware, Writer, associated cables & mouting accessories as completed

Supply, installation, Configuration, Testing & Commissioning of Hospitality Management Software with following Modules 1. Front Office Management2. Accounts Receivable3. Point of Sale4. Telephone Management5. Banquets & Conferences6. Food & Beverage Costing7. HR & Payroll8. Maintenance Management9. Materials Management10. Financial Management11. Membership Management12. Interface with Access Control, EPABX , CRM, Door Lock etc. Module to be customised as per Client Requirment. Cost should be incluiding trainning to client persons. incluiding all required license etc.

Supply, installation, testing & commissioning of Central Server with the minimum following specifications,: Intel® Xeon® Hexa processor, 3.2GHz, 6 Core, 16MB Cache memory, Intel HD Graphics , 1TB HDD, 32 GB DDR ECC Ram, Rack Mount Server with Database, OS (Microsoft SQL Server Standard Edition (Licensed Copy) – 2016/ latest), Firewall with Antivirus and Anti Malware subscription & Integrated SAS Controller (.Net Framework 4.5.1) should be loaded with lifetime license. The server shall have Integrated RAID 5 Controller, Redundant Power Supplies, DUAL 10/100/1000 Ethernet Card and Veritas/Seagate Online Backup Software with required accessories and licenses.

Supply, installation, testing & commissioning of Intel Core i7 Processor 4 GHZ . 8GB Ram Memory, Minimum 500 GB Hard Disk, 10/100/1000 NIC Card, HD Colour Monitor supporting 1024x1080 pixels Resolution with life time license of OS (Windows 10 Professional or latest), MS Office 2010 or Higher / Open Office & Antivirus Software incluiding all required accessories like Keyboard, Mouse , Cord, License etc.

Supply, installation, testing & commissioning of Point of Sales Hardware with minimum Intel Processor - Intel G540 / 2.5GHz / 2M Cache. 4GB Ram Memory, Minimum 320 GB Hard Disk, 10/100/1000 NIC Card, HD Colour Dual Monitor supporting 1024x1080 pixels Resolution with life time license of Supported OS - MSR ISO Track 1,2,3 / Operating System- POS Ready 7 (Full Version OS)/ Screen - LCD / TFT Touch Panel (Min 800x600 resolution) with 5-Wire Resistive, USB Interface incluiding all required accessories

Supply, Installation, Testing & Commissioing of HP Lesser Jet A4 Size Multi-format ( Printing, PDF Scanner & Xerox ) Colour Printer with required softwarea, Hardware & Tonner etc. as completed

SUB HEAD XLIX : ARBORICULTURE

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment)

a) Screened through sieve of I.S. designation 20 mm

b) Screened through sieve of I.S. designation 16 mm

c) Screened through sieve of I.S. designation 4.75 mm

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :

Holes 90 cm dia, and 90 cm deep

Holes 60 cm dia, and 60 cm deep

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

a) Trees Plant

b) Shrubs Plant

Complete maintenance of trees (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge. Trees for 250 no/(up to 4 & up to 3 year Slow & Fast growing group)

Complete maintenance of shrubs (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge. 2000 X 3 = 6000

Providing and stacking of Azadirachta indica (Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Dalbergia sissoo (Seasam) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in charge.

Supply and stacking of Adansonia digitata (kalp vricksh) plantof ht 150-165 cm in bag size of 25 cm as per direction of the officer-in-charge.

Supply and stacking of Delonix regia (Gulmohar) plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Supply and stacking of plant Nerium oleander (kaner) of height 60-75 cm. with 5-6 branches in poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara,Mohan,Scarlet Queen, Varigata, Glabra Formosa, Peruviana Odissi, Partha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) plant of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and Displaying Coleus broad leaves having 3 to 4 branches equal well developed with fresh & healthy foliage in different colour in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing of Schefflera Green (three in one), mounted on moss stick 90 cm, well developed with full of fresh & healthy leaves from bottom to top with rich foliage in 25 cm size of Earthen pot/Plastic pot.as per direction of officer-in-charge.

Providing and displaying of Phoenix palm plant, having ht. 75 cm to 90 cm with 10 to 15 or more leaves, well developed, fresh and healthy in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Philodendron sellum plant, having ht. 45 cm to 60 cm with 12 to 16 leaves, well developed, fresh and healthy foliage in 30 cm size of Earthen pot / Plastic pot & as per direction of the officer-incharge

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide , lawn mover and brush cutter with fuel will be provided by the Department & other T & P material/articles shall be provided by the contractor.) Permanent office accommodation. (as per yard stick 1Mali =1.25Acre)

SUB HEAD L :SOLAR WATER HEATING

Supply, Installation, Testing , Commissioning of 500 LPD Capacity ,Temperature up to 70 C,Solar water heating system consisting of 1 no. of BIS approved Evacuated Tube Collector (ETC) model solar water heating systems. Each system with stainless steel insulated Tank, Necessery supports for collectors & tank,Necessary Isolation valves,Non return valves,Strainers,temperature gauges,water meter,System interconnecting piping with insutaltion ,Air Vessle & safety valves including necesssary civil work like grouting of collectors stand, pipe supports, PCC uthalas for storage tank, necessary Electrical back up,including Hot water re circulation pumps , panel etc complete as directed.

Supply, Installation, Testing , Commissioning of 1000 LPD Capacity ,Temperature up to 70 C,Solar water heating system consisting of 1 no. of BIS approved Evacuated Tube Collector (ETC) model solar water heating systems. Each system with stainless steel insulated Tank, Necessery supports for collectors & tank,Necessary Isolation valves,Non return valves,Strainers,temperature gauges,water meter,System interconnecting piping with insulation,Air Vessle & safety valves including necesssary civil work like grouting of collectors stand, pipe supports, PCC uthalas for storage tank, necessary Electrical back up,including Hot water re circulation pumps , panel etc complete as directed.

R K Infra India Pvt Ltd (BID ID -3097330)

SHRI GURMUKHDAS CONTRACTORS PVT. LTD. (BID ID -3105036)

VISHAL BUILDERS (BID ID -3105275)

Vishal Infrastructure Ltd (BID ID -3102174)

GIRDHARI LAL CONSTRUCTIONS PVT LTD (BID ID -3109116)

Amara Raja Infra Private Limited (BID ID -3102981)