SPECIAL REPAIRS TO BLDG NO P-3 AT NAVY PARK UNDER GE HADDO, SRI VIJAYA PURAM

Amount

Taking down cement screed plaster on roof top, brick or stone walls etc, including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and as directed.

Demolition of cement concrete (Un reinforced) of any description as in padding concrete ( Other than ground floors) complete all as specified and as directed.

M & L for providing cement concrete type B0 1:2:4 of thickness 25 - 50mm (12.5mm grade stone aggregate) as in padding and benching & filleting all as specified and as directed

M & L for screed plaster 15mm thick plaster on RCC roof slab with CM (1:4) mixed with water proofing compound @ 3% by weight of cement on fair faces of concrete surface finished even and smooth without using extra cement. (Note : WPC shall be measured and paid seperately)

Supply only liquid water proofing compound

M&L for applying a coat of cold bituminous primer over cleaned surface @ 0.30 Kg/Sqm and applying one coat of hot blown bitumen 85/25 grade @ 1.2 Kg/Sqm over primer followed by APP modified polymeric membrane 3mm thick, minimum weight not less than 3 Kg/Sqm, reinforced with polyester non-woven fabric weight not less than 150 Gm/Sqm laid as per the manufacturer's instruction with side over lap of 100mm and end over lap of 150mm, tucked into the chases on vertical surfaces and painting over APP membrane sheet with aluminium paint @ 0.10 Kg/Sqm complete all as specified and directed

Dismantling plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern in roof coverings complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge etc fixed with self tapping screws complete all as specified and as directed.

M&L plain aluminium flat section not less than 0.68 Kg per RM as in wind tie fixed with aluminium self tapping screws complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed.

S&F mild steel roof trusses (framed), trrussed, purlins, crane gantries, rails and fastenings and heavy bracket framming (Beam,Tee, Angle, Channels or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description over 10cm width or girth not otherwise described complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint including preparation of old steel surfaces of any description over 10cm width or girth not otherwise described complete all as specified and directed

Excavation in post hole in hard/dense soil (or similar holes) each n. exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering, and removing surplus soil to a distance n. exc 50m and making good surface complete all as specified and directed

M&L for cement concrete 1:2:4 type B1 (Using 20mm graded stone agrregate) as in foundation of posts, railing and similar work complete all as specified and directed

M&L for preparing old surfaces of wood and wood based material exceeding 10cm in width or girth and applying one coat of synthetic enamel paint all as specified and as directed.

M & L for preparation of old wooden surfaces and applying melamine polish through the process of sanding with wood sanding paper of size 60 & 80 and applying wood filler mixed with NCD thinner including applying wood putty on shabby/ nailing area and sanding with sand paper of size 120 and applying sealer and walnut colour stainer and sanding with sand paper of size 320 and melamine polishing wiyh spray application and again sanding with 400 sand paper and finally applying silicon of make Waxpol with soft fine cloth for better shining and finishing complete all as specified and as directed.

Cutting channels, grooves or rebates with or without reinforcement n exc 15cm girth, and trimming surface for embedding the APP membrane/Galvalume sheet into the wall /column surface

Demolition of precast cement concrete block walling built in CM or cement lime Mortar complete all as specified and as directed

M&L providing precast cement concrete solid building blocks PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) or slabs 10cm thick (with plain or interlocking joints as directed) setting in cement mortar 1:4 in walls complete all as specified

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) and removing the rubbish from the site.

M&L for nominal mix RCC 1:1.5:3 type A1 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajja/facia and the like complete all as specified and directed

M&L formwork for rough finished flat surface to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed

M&L formwork rough finished surface of concrete to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work n. exc 10 cm wide complete all as specified and directed

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for 16-18mm thick granite of approved quality machine cut polished, bedded and jonted with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone as in cooking platform, counter of WHB and like over and including 15mm thick screed bed in CM 1:4 including grinding/chamfering and polishing the edges complete all as specified and as directed by Engr-in-Charge

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and as directed by Engr-in-Charge

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed

S&F for aluminium anodised snap grid frame work for ceiling 605mm x 605mm using aluminium anodised sections aluminium sections main tee 36.5X25X1.4mm, cross 23.5X26.4X1.4mm, angle 25X25x1.4mm including cutting, drilling jointing etc complete including 4mm dia of GI hangers wire suspenders fixed with adjustable connectors and providing 6mm thick E-boards (Classic) 605mm x 605mm size duly painted with two coats of oil bound distemper over a coat of primer all specified by Engr-in-charge complete all as specified and as directed.

M&L for seamless designed gypsum board false ceiling 12mm thick including for any sunk or raised moulding with 25mm long self drilling/ tapping screws having philips head with joining compound and 48mm wide fiber tape to provide seam less finish and including GI frame work of seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flange of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm c/c intermediate channel 0.9mm thick having two equal flanges of 15mm suspended from soffit at approx 900mm c/c with GI cleats and steel expansion fasteners with and incl ceiling section ( not exc 1.2m length) of 0.55mm thick having kurled web of 50mm an flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting across the intermediate channel at 457mm c/c incl hangers 6mm dia GI adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete and finally applying two coats of oil bound distember with roller finish over a coat of chalk whiting primer cmplete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed

Demolition of cement concrete un-reinforced in any position and paving not exc 15cm thick above or below ground level complete all as specified and as directed.

M&L for light shade vitrified ceramic tiles minimum 8mm thick (square/ rectangular) polished area of each tiles n. exc 0.36 Sqm (600x600mm) in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed

M&L for light shade vitrified ceramic tiles minimum 8mm thick (square/ rectangular) polished area of each tiles n. exc 0.36 Sqm (600x600mm) in vertical surfaces such as skirting, dados and riser etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed of cement mortar 1:3 complete all as specified and directed

M & L PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) 25mm thick as in levelling course, sub-floors and paving etc complete all as specified.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tiles exc 0.06 Sqm but n. exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed of CM (1:4) bedding complete all as specified

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc 0.11 Sqm but n. exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 complete all as specified and directed

M&L for coloured Glazed ceramic tiles in vertical surfaces 350x250x7mm/300x450x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement over and including 10mm thick rendering or bedding layer of cement mortar 1:3 complete all as specified and directed

Demolition stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed

M&L for chequered cement concrete tiles of size 30cm X 30cm X 25mm thick with grey cement and pigments set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor over and including 20mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for 75mm thick PCC 1:4:8 type D2 (Using 40 mm graded stone aggregate) as in path laid in panels, finish the top surfaces even and smooth complete all as specified and directed

M & L for heavy duty designer Vitrified tiles of size 300 X 300 X 10.8mm thick, or high dimension (except thickness) of any colour any design Durastone, weather proof impact resistant, abrasion resistant exterior tiles, as in floors etc , set and jointed in neat cement slurry over and pointed in white or coloured cement to match, over 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed

M&L for 10mm thick plaster in CM 1:6 on fair face of concrete surface or brick walls finished even and smooth without using extra cement complete all as specified

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of average 1mm thick wall care putty to make the surface smooth complete all as specified and directed

M&L for applying two coats of oil bound distemper over a coat of average 1mm thick wall care putty to make the surface smooth after complete removal of existing treatment complete all as specified and directed

M&L for 15mm thick plaster in CM 1:4 on fair face of brick walls or concrete surface including mixing of water proofing compound, finished the surface even and smooth without using extra cement complete all as specified. (Note: Water proofing compound shall be measured and paid separately)

M&L for preparing newly plastered wall surface and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm complete all as specified and directed

M&L for complete removal of existing treatment on plastered wall surface and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm complete all as specified and directed

Cutting out existing cracks in concrete surfaces/masonry wall/slab forming grooves of 25mmx40mm size, cleaning the groove thoroughly with blower, applying primer coat of the mix of IPH CC or Hydroseal siliconate epoxy resin and hardner in equal proportion with spray gun suitable brush to form a film on the surface of groove, filling the groove with putty made by mixing IPH CC in equal proportion of make Harjas coating and polymers or hydroseal siliconate epoxy resin hardner and admixture in the proportion of 1:1:2 and finally applying the sealing coat of the same mix and in the manner primer coat is applied with following minimum coverage per running meter of groove :- Material : Priming coat putty filling seal coat, Resin 60gms 100gms 40gms, Hardner 60gms 100gms 40gms, Admixture 400gms

M&L for 10mm thick plaster in CM 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement complete all as specified

M&L for preparation of newly plastered ceiling surface and applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty complete all as specified and directed

M&L for applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty on ceiling after complete removal of existing treatment complete all as specified and directed

Taking down chowkhats or frames area n. exc 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed

Taking down Chowkats exc 1.5 Sqm but n. exc 4 Sqm each with shutters (Without taking off shutters from the frame) complete all as specified and directed

S&F for 2nd class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed

M&L for anodised aluminium frame for doors, windows, ventilators, partition with one or more rebates including joining cleat for fixing etc complete as specified

M&L for anodised aluminium door shutters, aluminium section weighing not less than 1.55 Kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, tower bolts, anodised aluminium snap beading screws etc complete all as specified. Note : Supply only floor spring, glass, SS friction hinges, particle board, wire gauze will be measured seperately

M&L for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing not less than 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified complete all as specified. Note : Supply only glass, particle board, wire gauze will be measured seperately

S&F sheet glass 4 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window/ventilator shutter not exc 0.5 Sqm in each pane

S&F Anodised aluminium grill of approved pattern cut to required size/shape and fixed with position with aluminium bedding & frame with & including F sections, fixed to aluminium windows/ventilators complete all as specified and directed.

S&F 12mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination, fixed with screws to timber frame work complete all as specified

S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire staples all as specified and directed

S&F 100mm size stainless steel butt hinges medium weight complete all as specified

S&F 200mm aluminium, anodised, barrel tower bolts of extruded section all as specified

S&F 150mm aluminium, anodised, barrel tower bolts of extruded section all as specified

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised all as specified

S&F 300 mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet sliding bolts of extruded sections and fixing bolts and sliding bolts of extruded section all as specified

M&L for applying two coats of synthetic enamel paint to new undecorated wooden surfaces over a coat of pink primer including preparation, over 10cm width or girth complete all as specified

M&L for preparation of old painted surfaces of wood and wood based surfaces of any description, not otherwise described and applying one coat of synthetic enamel paints over 10cm width or girth complete all as specified and as directed

S&F door closer hydraulically regulated aluminium (die cast) body, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified

M&L for 18mm thick HDF boarding (fire & water proof) as in cup boards exterior grade with one side white lamination and other side coloured prelaminated, size of the cabinet as per requirement of the site complete all as specified and as directed by Engr-in-Charge. Make : bajaj/ Axis/Greenply/ Amnchidply / or equivalent (Note : (i) Cutting edges of cupboard shutter/shelves to be finished with adhesive edge binding tape all as directed)

S&F stainless steel auto closing hinges 35mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified. Make : Hettich/Harrison/Dorsel

S&F stainless steel non megnetic bow handle "D" type anodized 150mm long complete all as specified. Make : Hettich/Harrison/Dorsel

S&F stainless steel non megnetic barrel tower bolt 100mm long of extruded section complete all as specified. Make : Hettich/Harrison/Dorsel

S&F telescopic ball bearing runners minimum length 400mm (KA 5632) full extension load capacity 45 Kg complete all as specified. Make: Godrej/Hettich/Kaff

Dismantling PVC water tanks exc 500 Ltr but n. exc 1000 Ltr capacity and removing to store complete all as specified

S&F double layer rotational moulded PVC water storage tank cylinderical, vertical with closed top hoisted and fixed in position tank capacity 1000 Ltr with and including PTMT float valve 20mm dia and making connection for inlet and outlet complete all as specified and directed

Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed

S&F 20mm outer dia CPVC pipes SDR 13.5 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including suitable reducer for 15mm dia taps fitting as required complete all as specified

Taking up or down 25mm dia steel tubing connection, including cleaning for refixing or removal to store

S& F for 25mm bore unplasticised PVC pipe of pressure ratings 10kgf/Sqcn including all fittings fixed complete to walls, ceiling or in floor etc complete all as specified and directed

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth complete all as specified and directed

S&F 20mm bore gun matel globe or gate valve with iron wheel, screwed both ends for iron pipes complete all as specified

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories complete all as specified and directed

S&F mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging, fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed

Dismantling of 110mm dia cast iron/PVC pipes incl bends/branch pieces jointed in cement mortar and taking out if required complete all as specified and directed

S&F PVC (SWR) pipe 110mm bore, single socketed, in any length including bends, socket etc with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed

S&F PVC (SWR) pipe 110mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed

S&F PVC (SWR) 110mm dia bend of any radius and jointed with approved adhesive complete all as specified and directed

S&F PVC (SWR) 110mm dia junction single (single T) equal or unequal reducer 'T' 110mm to 75mm dia and jointed with approved adhesive complete all as specified and directed

S&F PVC (SWR) vent cowl 110mm dia jointed with approved adhesive complete all as specified and directed

S&F in repairs stainless steel grating cover 100mm dia fixed with white cement all as specified and directed.

Dismantling of 75mm dia cast iron/PVC pipes incl bends/branch pieces jointed in cement mortar and taking out if reqd complete all as specified and directed

S&F PVC (SWR) pipe 75mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive fixed to walls complete all as specified and directed

S&F PVC (SWR) bend 75mm dia, any radius as required and jointed with approved adhesive complete all as specified and directed

S&F 75mm outlet dia PVC (SWR) floor trap with grating including jointing with solvent cement to waste pipe complete all as directed

S&F solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stils & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

S&F in repair vitreous china wash down water closed pan (Pedestal pattern) white, including connection to drain (or out going pipe) and to flush pipe, antisypthonic (excluding flushing cistern and flush pipe) complete all as specified

S&F in repair vitreous china wash down water closed pan (Pedestal pattern white) standard size with 'S' or 'P' trap and other connecting items approved brand including fix with white cement complete all as specified. Make : Jaquar Pt No (LYS WHT 0314) or Equivalent in CERA/PARRYWARE/JOHNSON.

S&F plastic water closet seat cover, white, closed pattern with flat bottom including mild steel chromium plated or aluminised hinging device complete all as specified

S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action push type with inlet ball valve and float including flush pipe long 32mm dia, ball valve, handle, bracket etc complete all as specified and directed

S&F in repair vitreous china counter wash hand basin oval shape of size 550x400mm including brackets, 32 mm CP waste coupling, chain and plug, waste fittings all necessary inlet and out let connections complete all as specified

S&F for fixed in repairs wash hand basin vitreous china white (flat back) of size 550x400mm including 15 mm dia pillar cock , CI bracket 15mm dia polythene connection 450mm long , 32mm dia waste coupling and 32mm dia PVC waste pipe 450mm long etc. complete all as specified, including taking down the existing wash hand basin all as specified and directed.

S&F flush pipe of polyethylene of low or high density or PVC 32 mm dia flexible pipe suitable for WHB/sink/urinal etc complete all as specified

S&F in repair PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer complete all as specified

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified and directed.

S&F 0.63mm thick SS sheet stainless steel kitchen plate rack of size 31" x 30" x 10" standard quality complete all as specified and directed. Make : Blue star, Prayag, Silver Shine

S&F in repair mirror cabinet PVC/fiber of size 550x520x100mm with sliding mirror 4mm thick 2 Nos of size 240x290mm with built in rack of size 230x150x90mm with PVC plug etc with CP towel rail of length 270 mm and 100 mm dia complete all as specified. Make : Supreme/Prince/Prayag/Jaguar

S&F in repair CP WHB mixture cast copper alloy with central hole for WHB and ling shank fancy type 15mm bore complete all as specified. Make : Jaguar Cat Part No - Con-167KNB or equivalent in Prayag / Prince

S&F in repair CP brass hot and cold 15mm dia wall mixture 3-in-1 system with provision for both hand shower and overhead shower complete with 115 long bend pipe, connecting leg and wall flange complete all as specified. Make : Jaguar Cat Part No - Con-281KN or equivalent in Prayag / Prince.

S&F in repair CP overhead shower rose 105mm dia round with revolving joints (with body rotation) and 115mm long shower arm with rabit cleaning system and all fittings complete all as specified. Make : Jaguar Cat Part No - OHS-1709 or equivalent in Prayag / Prince

S&F in repair chromium plated brass shower roses with or without swivel joints square type 125mm size including shower arm complete all as specified

S&F in repair CP brass 15mm hand shower (health faucet) (ABS body) with 1.5m long easy flexible tube in chrome finish and wall hook complete all as specified. Make : Jaguar Cat Part No - ALD-587 or equivalent in Prayag / Prince

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed

S&F toilet paper holder complete all as specified. Make : Jaguar Cat Part No - ACN-1151N or equivalent in Prayag / Prince.

S&F in repair single towel rail 600mm long complete all as specified. Make : Jaguar Cat Part No - AQN-7711 or equivalent in Marc/Plumber

S&F soap dish complete all as specified. Make : Jaguar Cat Part No - AQN-7731 or equivalent in Prayag / Prince.

S&F in repair CP bib cock 15mm dia with crutch handle as approved fancy type long body complete all as specified. Make : Jaguar Cat Part No - Con-107KN or equivalent in Prayag / Prince.

S&F in repair 15mm dia cast copper alloy chromium plated long body bib tap fancy type with wall flange complete all as specified and directed.

S&F in repair CP bib cock 15mm dia with crutch handle as approved fancy type two way long body complete all as specified. Make : Jaguar Cat Part No - Con-041KN or equivalent in Prayag / Prince.

S&F in repair concealed stop cock with wall flange including all fittings complete all as specified. Make : Jaguar Cat Part No - Con-083FTK & ALD-089CQT or equivalent in Prayag /Prince.

S&F in repair 15mm Stop valve angle cock cast copper alloy, fancy type, chromium plated with long shunk and cup high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified

S&F in repair CP angle cock 15mm dia fancy type cast copper alloy complete all as specified. Make : Jaguar Cat Part No - Con-053KN or equivalent in Prayag / Prince.

S&F in repair 15mm concealed type angle cock cast copper alloy, fancy type, chromium plated with long shunk and cup high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified

S&F corner glass shelf with bracket complete all as specified. Make : Jaguar Cat Part No - ACN-1173 or equivalent in Prayag / Prince.

Cutting down vegetation growths like plants/trees of girth n.exc. 60 cm from roof tops/ parapet walls, external walls of buildings, chajjas, wall junctions including removal of roots and taking out carefully possible quantity of concrete in roofs embedded in walls/slab surfaces and applying TUFALO chemical (herbal medicine) to arrest further growth and making good the disturbed surfaces with PCC (1:11/5:3) type B-1 or in cement mortar (1:2) upto 12 metre height complete all as specified and directed. Note: The unit rate quoted shall be deemed to include the cost of scaffolding/staging etc. as necessary to execute the work.

Taking down carefully copper/aluminium point wiring for light, fan, socket or power point etc complete with all fittings and fixtures such as switch piano, ceiling rose switch, socket, Pendents etc including making good surface of wall, ceiling etc complete all as specified and directed.

Taking down fuse Unit/DBs, 415 Volt/230 Volt incl MCCB/MCB complete all as specified and directed

Taking down old aluminium sub main wiring of any size complete all as specified and directed

M & L point wiring complete with 1100 volts grade, 1.5 sq.mm (nominal area), single core, FRLSH PVC insulated ,unsheathed, multi stranded copper conductor cable drawn through and including medium grade, rigid , non-metallic PVC concealed/ on surface conduit of size not less than 20 mm dia, with all necessary fittings, concealed in walls/ floor or surface on wall/ roof duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire and connecting to common earth duly including suitable size of factory made fabricated MS sheet modular terminal box, flush mounting in the wall for mounting switches/switch socket combinations/ fan regulators etc., covered with suitable size of modular cover plates complete in making good the existing surface with existing colour coding as required at site complete all as specified for the following :-

Note :- The unit rate quoted shall deemed to include the cost of following :- (a) GI metal flush box of minimum thickness of 1.6mm and modular cover plate with frame of any module complete. (b) Proper colour coding is to be followed as per IS specification. (c) Wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement. (d) Cutting chases in wall/floor /beam/ceiling to be concealed conduit and making good the disturbed surfaces.

All as per Srl item No 133 above, but , One light/fan point controlled by one switch 5 Amps one way complete all as specified and directed.

All as per Srl item No 133 above, but , for two light point controlled by one switch 5 Amps one way complete all as specified and directed.

All as per Srl item No 133 above, but, point wiring for 5 pin switch socket outlet , 6 Amps on independent board complete all as specified and directed.

All as per Srl item No 133 above, but, point wiring for 5 pin switch socket outlet , 6 Amps on same board complete all as specified and directed.

All as per Srl item No 133 above, but,One bell point controlled by one bell push switch 5 Amps one way complete all as specified and directed.

All as per Srl item No 133 above, but , point wiring with two single core 4.0 sqmm size cables and one 4.0 sqmm green colour cable as earth continuity conductor for one 6 pin 16 Amps socket out let on independent board complete all as specified and directed.

All as per Srl item No 134 above, but, point wiring for one 6 pin 16 Amps on same board complete all as specified and directed .

Supply & fixing for switch modular type, 6 Amps 1 module, 230 volts AC circuit complete all as specified and directed. Make : Anchor (Roma), Legrand, L&T , Havells

Supply & fixing for switch modular type, 16 Amps 1 module, 230 volts AC circuit complete all as specified and directed. Make- Anchor (Roma), Legrand, L&T, Havells

Supply & fixing for socket outlet modular type 1 way 6 Amps, 3 pin, flush type 230 volts AC circuit complete all as specified and directed. Make- Anchor (Roma), Legrand, L&T, Havells

Supply & fixing for switch socket outlet, modular type 16 A, 3 pin, flush type controlled by one switch 230 volts AC circuit complete all as specified and directed. Make- Anchor (Roma), Legrand, L&T , Havells

Supply & fixing modular bell push 6 Amp one module 230 V AC . Make- Anchor (Roma), Legrand, L&T, Havells

Supply & fix Modular Ac Box With 20A DP MCB "C' Type, Metal Enclosure & Unbreakable Heavy Duty With ISI Plug Top, 240 volts AC supply for air conditioner, flush mounting in the wall complete all as specified and directed. Make:- Anchor (Roma) model no 98492 or equivalent in L&T / Havells

S & F communication modules for Telephone Socket with shutter (RJ 11) -1M code No.ACAKHAW000. Make: Havells (crabtree)/ Anchor/ L & T

S&F , Electric Bell, single pole working on 230 volts AC supply complete all as directed by Engineer -in- charge Make- Anchor , Legrand, L&T

S & F stepped type modular fan regulator, 2 modular type complete all as specified and directed. Make : Roma (Anchor)/ Legrand/ Havells

Taking down carefully ceiling fan of any make, size from its location, dismantling complete, examine complete parts thoroughly, oiling, greasing all parts and complete overhauling of fan including replacement of small parts such as split pin, nut bolt, screws and assembling back the fan, make fully functional, re-fixing the fan to its position including replacing and providing of twin core copper wire 23/0.0076 from fan to ceiling rose and painting the fan with same colour of fan complete all as directed.

Taking down carefully Exhaust fan of any make, size from its location, dismantling complete, examine complete parts thoroughly, oiling, greasing all parts and complete overhauling of fan including replacement of small parts such as split pin, nut bolt, screws and assembling back the fan, make fully functional, re-fixing the fan to its position including replacing and providing of twin core copper wire 23/0.0076 from fan to ceiling rose and painting the fan with same colour of fan complete all as directed.

M & L Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface with or without reinforcement all as specified and as directed by Engineer-in- Charge.

Supplying, fixing and testing Tube light fittings aluminium housing, Diffuser slim Integrated design LED 21 watts 4 feet, IP-20 including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed. Make: Philips Cat Part No : BN021C LED22S or equivalent to CG/ Havells/ Luker

Supplying, fixing and testing Tube light fittings aluminium housing, Diffuser slim Integrated design LED 10 watts 2 feet, IP-20 including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed. Make: Philips Cat Part No : BN021C LED12S or equivalent to CG/ Havells/ Luker

Supply and fixing and testing Mirrior light fitting of cap 20 watt with all fixing arrangements all as specified and directed. Make-Havells cat no LHLDESAARANC020 or equivalent to Philips/ CG

Supply & fixing LED single head wall light, metal and glass body , with lamp base B22 with bulb 9 watt with all accessories complete all as specified and directed. Make : Philips Model No : 30978 or euivalent to Havells/CG

S & F of 22 watts surface mounted LED downlighter fitting , WW/CDL/NW colour as reuired as site with slim high perfomanance surfaced mounted LED light fittings, round/square shape as required at site made from die-cast aluminium and CRCA covering, powder coated in white colour complete all as specified and directed. MAKE: Philips Surface Mount+ LED Surface Downlighter 22 W or equivalent make of Havells/CG

All as per item No 152 above, but ,15 watt complete all as specified and directed. MAKE: Philips Surface Mount+ LED Surface Downlighter 15 W or equivalent make of Havells/CG

Supply & fixing LED vivid Pendant light fitting with LED lamp E 27 type of cap 15 watt, aluminium body (colour Ivy league/ Matte gold/ Splendid blue as required) complete all as specified and as directed. Make : Philips Model No : 582024 or euivalent to Havells/CG

Supply and fixing of Decorative ultra slim linear LED lighting fixture of 15 Watt recess mounted 220V , 50Hz with extruded Polycarbonate, Aluminium heat Sink ,environmental friendly energy efficient fitting recess mounted round/square in shape (Warm white/white colour as per requirement) of light as required at site complete all as specified and directed. Make - Philips Cat Part No : Dura Slim or equivalent make in CG//Havells

All as per item No 155 above, but , 7 watt complete all as specified and directed. Make - Philips Cat Part No : Dura Slim or equivalent make in CG//Havells

Supply & fixing LED bed side lamp of capacity 3 watts with lED bulb (white/yellow colour of light as required at site) complete all as specified and directed. Make : Philips Model Moden No : 48042 or euivalent to Havells/CG

S & F 30 watts LED building security light fittings , pressure die cast aluminium housing powder coated graphite grey and toughened glass of IP 65 with pranuts including necessary fixing arrangements as per site requirements class all as specified and directed by Engr In charge. Make : Luker Cart Part No: LSTE030S or equivalent to Philips /Havells/ CG

Taking down old unsv street light brackets of any size and Supply and fixing new GI brackets of GI pipe light grade of size 25 mm dia including nuts, bolts and washers for building security light complete all as specified and directed.

Taking down carefully old unserviceable water heater of capacity 25 liters and refixing the same with painting of two court of synthitic enamaled paint complete all as specified and directed.

S & F Sub main wiring with PVC insulated FRLSH cable 2 runs of single core 6 sq mm 1100 V grade with stranded copper conductor cable using proper colour coding Phase Red/Yellow/Blue, Neutral- black and earth- green in and incl rigid PVC concealed conduit (ISI marked) incl all specials/accessories etc and provision of PVC insulated FRLS copper conductor single core 6.0 sq mm for earth continuity complete all as specified and as directed. NOTE: Two runs of 6.0 Sqm copper conductor, One run of 6.0 Sqmm copper conductor as earth wire and one run of PVC conduit shall be measured as one unit length.

All as item No 161 above, but , Submain wiring with 2 runs single core 4.0 sqmm cable with same size of earth wire complete all as specified and as directed.

Alll as item No 161 above, but , Submain wiring with 2 runs single core 1.5 sqmm cable with same size of earth wire complete all as specified and as directed. Note for item No 162 to 163 : 3 length of cable and one length PVC Conduit shall be measured and paid for one length

All as item No 161 above, but , Submain wiring with 3 runs single core 6.0 sqmm cable with same size of neutral and earth wire complete all as specified and as directed. NOTE:- 4 length of cable and one length PVC Conduit shall be measured and paid for one length.

S & F DB VTPN sheet metal enclosure double door IP 43 protection, door earth suitable for incoming upto MCCB 160 Amps/200 Amps & outgoing MCB TP / SP. Triple pole and neutral 415 V 6 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete including taking down old unserv DB of any type /rating and making good to the distrubed surface /walls all as specified and directed.

S & F in replacement of MCCB, 3 pole, 100 Amps, 50Hz, 25KA rupturing capacity, 415 Volts adjustable type with thermal and magnetic release alongwith copper separator terminals complete all as specified and as directed.

S & F SPN DB sheet metal enclosure double door suitable (IP-43) Protection 12 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete all as specified and directed.

All as item No 167 above, but , 8 way complete all as specified and directed.

Supplying & fixing MCB SPN 32 Amps (`C’ series) having current rating 10 KA complete all as specified and directed .

Supplying & fixing MCB single pole, 6 to 32 Amps (`C’ series) having current rating 10 KA complete all as specified and directed .

Supplying & fixing RCCB 25 Amps (`C’ series) having current rating 10 KA complete all as specified and directed.

Supply and fixing with wall by suitable size of fastner, wall mounted bus bar chamber 100 A TPN with aluminium bus bar 4 Nos, IP-42, suitable for incoming and outgoing of UG XLPE Cable of size 35 sqmm 3.5 core with glands complete all as specified and directed.

Taking down carefully existing electronic energy meter of any capacity and any size and refixing the same location after completion of B/R work complete all as specified and directed.

Supply & fix of FRP meter box of size (inside) 390 x 225 x 140 mm including taking down the old/unserviceable meter boxes all as specified and directed. Make : SINTEX Cat No. GSMB-3923 or equivalent to Hensel

Earthing complete with galvanised earth plate electrode 60 cm x 60cmx 6.15 mm thick, buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the earth plate not less than 1.5m below ground level , connected to GI earth wire 4 MM Dia as earthling lead by means bolts and nuts check nuts and washers of galvanized iron and connected to main switch board including watering arrangement with PCC chamber , MS funnel with wire mesh,. CI cover with frame etc including necessary excavation in any type of strata , returning, filling removal of soil outside MD land ,filling of charcoal and salt complete all as shown in electrical plate No. 3 of MES Sch Part I , connected to Earthing test point all as specified and directed on testing on completion. NOTES: 1) The unit rate shall also include for earth work in any type of soil, PCC (1:3:6) type C1 chamber, pre-cast RCC (1:2:4) type B-1 using 20mm graded stone aggregate cover 50mm thick reinforced with TMT bars 8mm dia @ 100mm c/c both ways, funnel with watering pipe 20mm dia medium grade, GI protection pipe light grade 40mm dia and wire mesh complete in addition to item No. 1(a) to (e) of preamble (notes) under sub-heading earthing, specified on Sl. Page Nos. 451 & 452 of SSR Part-II. 2) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.

Excavation in trenches n. exc 1.5m wide and n. exc 1.5m in depth in soft/loose soil for foundation of poles (or) cable laying complete all as specified and directed

Returning filling incl spreading levelling watering and well ramming in layers n. exc 25cm thick for cable laying complete all as specified and directed

Removing excavated material (any type of soil) to a distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed

Supply, laying, testing and commissioning of LT XLPE insulated, sheathed, armoured multistranded aluminium conductors, heavy duty electric cable 1100 Volts grade of size 3.5 core x 35 sq.mm. IS-7098, Part-I marked, laid in trenches, ducts, pole, wall ,footpath, cable tray , cable route diversions , under services etc complete all as specified and as as directed by engineer in charge. Note: (i) Necessary test results like continuity test, megger tests, shall be submitted to Engineer-in-Charge before the cable is laid. (ii) Excavation earth work will be measured and paid separately. (iii) The cable should be clamped with 1mtr interval with wall if necessary.

Supply and laying HDPE DWC pipe of size 50mm (OD) x 38mm (ID) along with connected accessories like couplers, bends, end caps etc. for LT cable protection complete all as specified and as directed by engineer in charge. Make : REX POLY EXTRUSION LTD / TIRUPATI PLASTOMATICS PVT LTD/ PRINCE/ JAIN IRRIGATION SYSTEMS LTD

CARTWHEEL CONSTRUCTION (BID ID -3388441)

CHANDER SEKER ENTERPRISE (BID ID -3385728)

M/s K Moorthi (BID ID -3385301)

M/s Prem Enterprise (BID ID -3385690)

LOOK UP ENTERPRISES (BID ID -3387723)

NAWAZ CONSTRUCTIONS (BID ID -3387872)

V KARTHICK (BID ID -3384510)

M/s Ramesh Lal (BID ID -3385029)