REPAIR / MAINTENANCE OF BORE WELL, PUMPSETS, STARTERS, CONTROL PANEL, CI/GI WATER PIPE LINES, VALVES AND VALVE CHAMBER, CLEANING OF RCC WATER STORAGE TANKS AND ALLIED WORKS AT AF STN KALAIKUNDA

Amount

Supply only Calcium hypochlorite 65% to 70% content in granular form to be used as a disinfectant for water treatment and packed in 45 kg in each plastic drum and delivered to AGE (E/M) store yard all as specified and directed by Engineer-in-Charge. Note :- 1. Approval of chemical ( calcium hypochlorite) shall be given after verification of test certificates and their chemical analysis , strength in terms of quantity of chlorine content. 2. The brand/make of chlorination chemical must be certified by Govt. Laboratory and confirming compliance of specification , suitable for drinking water.

Supply only Aluminum Sulphate(Alum) fine powder suitable for water treatment to clear water as a flocculant for swimming pool/ Treatment plant and delivered to AGE (E/M) store yard as specified and directed by Engineer-in-Charge. Make : ISI marked or any make or brand approved by Garrison Engineer.

Supply only Chlorine liquid as per IS 11673 grade-II ( 10-12% free chlorine) Sodium Hypochlorite solution for disinfection, algae control, and coagulation of swimming pool water packed in container and delivered to AGE (E/M) store yard as specified and directed by Engineer-in-Charge. Make : ISI marked or any make or brand approved by Garrison Engineer.

Supply only bleaching powder, grade 1 as per IS 1065: 1989, minimum 35 percent chlorine available by mass, 1/15 max loss of chlorine on the basis of initial available chlorine, 99.5 percent minimum particle size by mass all as specified.

Supply of super white Lime fine powdered free from Ash & Dirt of best quality (used in drinking water) in factory sealed packet and delivered to AGE (E/M) store yard as specified and directed by Engineer-in-Charge. Make : ISI marked or any make or brand approved by Garrison Engineer.

Supply & fix dosing pump roller assembly of as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through any other Agencies as approved by GE with and including taking out old unserviceable roller assembly complete all as specified and directed by Engr-in-Charge. Make :- As per sample or as per existing make and capacity

Supply & fix dosing pump tube as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through any other Agencies as approved by GE with and including taking out old unserviceable pump tube complete all as specified and directed by Engr-In-Charge. Make :- As per sample or as per existing make and capacity

Supply & fix dosing pump weighted suction line straineras per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through any other Agencies as approved by GE with and including taking out old unserviceable dosing pump weighted suction line strainer complete all as specified and directed by Engr-In-Charge . Make :- As per sample or as per existing make and capacity

Supply & fix dosing pump Injection check valve as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through any other Agencies as approved by GE with and including taking out old unserviceable Injection check valve complete all as specified and directed by Engr-In-Charge. Make :- As per sample or as per existing make and capacity

Supply & fix dosing pump white suction /discharge tubing as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through any other Agencies as approved by GE with and including taking out old unserviceable dosing pump suction/ discharge tubing complete all as specified and directed by Engr-In-Charge. Make :- As per sample or as per existing make and capacity

Supply & fix dosing pump check valve duckbill only as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through any other Agencies as approved by GE with and including taking out old unserviceable dosing pump check valve duckbill complete all as specified and directed by Engr-In-Charge. Make :- As per sample or as per existing make and capacity

Supply & fix dosing pump connecting nut with adapter as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through any other Agencies as approved by GE with and including taking out old unserviceable connecting nut complete all as specified and directed by Engr-in-Charge. Make :- As per sample or as per existing make and capacity

Supply & fix dosing pump ferrule suitable for as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through any other Agencies as approved by GE with and including taking out old unserviceable dosing pump ferrule complete all as specified and directed by Engr-In-Charge. Make :- As per sample or as per existing make and capacity

Taking out old unserviceable Aquafit Agitator 120 watt 900 RPM single phase flange mounted motor with plastic shaft and impeller of Chlorine dosing sysetm by disconnecting with service tank including .rewinding, bushing and Comprenesive maintenance as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through any other Agencies as approved by GE and repair including renewal/replacement of defective parts as per Original Equipment Manufacturer's (OEMs) reccommendations complete and reconnecting with testing all as specified and directed by Engr-in-Charge.

Taking up/down old unserviceable any type column pipe and supply & fix MS column pipe 100 mm dia bore, heavy duty, 10 feet long each with flanges screwed and welded both ends complete with nuts , bolts , gasket etc for jointing pipe and lowering into bore well complete all as specified and directed by Engr-In-charge.

Supply and connection repairs column pipe 50 MM bore both and flanged made out of GI tubing heavy grade welded at end of column pipe cutting of groove to house submersible cables 3 core 6 sqmm (total length of each column pipe = 3.10 meter including flange at both end) complete all as specified and as directed.

Supply & Fixing Top cap for tubewell of 250mm bore with 8mm thick MS plate including arrangemement of making connection with delivery line and fixing column pipe as per ( OEMs) reccommendations and taking out old unserviceable complete all as specified and as directed by Engr-in-Charge.

Supply and fix only PVC coated steel wire rope 10mm dia with U clamps of suitable size securing the submersible pump motor and taking out old unserviceable complete all as specified and as directed

Supply and fix only PVC insulated & sheathed Submersible flate cable 6 Sqmm x 3 core copper conductor 1100 volt grade, ISI Marked, confirming to IS:694/2010, and taking out old unserviceable complete all as specified and as directed Engr-in-Charge.

Material and labour for Joint with rubber or leather gasket for flanged pipes/Sluice Valve/NRV/ARV and any other type of valve and fittings of dia 100mm bore with incl nut, bolts, washers etc. and taking out old unserviceable complete all as specified and Engr-in-Charge.

Material and labour for Joint with rubber or leather gasket for flanged pipes/Sluice Valve/NRV/ARV and any other type of valve and fittings of dia 150mm bore with incl nut bolts, washers etc and taking out old unserviceable complete all as specified and Engr-in-Charge.

Supply & Fix fully automatic star delta Submersible pump starter in sheet steel enclouser suitable for 20 HP pump set , 3 phase , 415 volt , 50 Hz , including making all electrical connection to run the pump and taking out old unserviceable complete all as specified and directed by Engr-In-Charge. Make:- C&S Cat Part No- BE3-SPSDDX254 322 or equivalent in L&T/BCH

Supply & Fix fully automatic star delta Submersible pump starter in sheet steel enclouser suitable for 15 HP pump set , 3 phase , 415 volt , 50 Hz including making all electrical connection to run the pump and taking out old unserviceable complete all as specified and directed by Engr-In-Charge. Make:- C&S Cat Part No- BE3-SPSDDX254 321X or equivalent in L&T/BCH

Supply & Fix DOL pump starter in sheet steel enclouser suitable for 7.5 HP pump set , 3 phase , 415 volt , 50 Hz including making all electrical connection to run the pump and taking out old unserviceable starter complete all as specified and directed by Engr-In-Charge. Make:- C&S, Cat part No - BE1SPSDDX204 321-HM or equivalent in L&T/BCH

Supply & Fix DOL pump starter in sheet steel enclouser suitable for 3 HP pump set , 3 phase , 415 volt , 50 Hz including making all electrical connection to run the pump and taking out old unserviceable all as specified and directed by Engr-In-Charge. Make:- C&S Cat Part No- BE1-SPSDDX204 310-HM or equivalent in L&T/BCH

Supply & Fix DOL Surface Mounted Mini Manual Motor Starter in sheet steel enclouser suitable for 02 HP pump set, 1 phase, 220 volt, 50 Hz, including making all electrical connection to run the pump and taking out old unserviceable starter complete all as specified and directed by Engr-In-Charge. Make:- C&S Cat Part No- BE1-SSDCEDP202U5T12H or equivalent in L&T/BCH

(a) Lifting of defective submersible pump set of any make and capacity 7.5 HP from after providing lifting tools , chain pulley etc. as required carefully, by disconnecting/dismantling all electric connections, column pipes, steel ropes/chain and keeping them under safe custody for reuse and Comprehensive maintenance as per Original Equipment Manufacturer's (OEMs) reccommendations installed at various locations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE including rewinding of burnt submersible motor 7.5 HP , 3 phase ,415 V, 50 Hz of any make with water proof insulated copper conductor of the same specification as per old one after dismantling / cutting out burnt windings from stator assembly, cleaning slots properly complete with insulating slots packing, sleeves, papers & reassembling stator and rotor after replacement of worn out spares/matching works including painting with two coats of synthetic enamel paint over a coat of red oxide primer after preparation of motor external surface and water proof jointing for submersible cable 3 core, with replacement of oil seal, sand guard, bolt gasket, cable packing ring, circlip, bearing bush upper & lower etc.and applying two coats of synthetic enamel paint over a coat of red oxide primer after preparation of pump external surface complete all as specified and directed. all complete and (b) Lowering of repaired /overhauled/rewinded submersible pumping set of any make and capacity after proper coupling of pump and motor , fixing old/new chain with clamp, connecting/refixing existing/new column pipe lines with new rubber gasket 3 mm thick, nuts, bolts & washers carefully with the help of chain pulley etc. & carefully re-connecting all electric/water lines and testing on load to the entire satisfaction of Engineer-in-charge complete. NOTE : (i) The cost of transportation of the defective submersible pumping set ( pump or motor ) from site to OEM workshop & back is deemed to be included in the quoted rates. (ii) Column pipe/ submersible cable/supporting chain required new will be measured and paid separately as supply only (iii) Repair of motor and pump measured separately (iv) refixing of column pipe to be done after proper descaling . (v) Each maintenance job shall be covered period of 09 Months..(vi) All minor spares required for making the pump functional shall be provided by contractor without any extra cost.(vii) Breakdown Maintenance : The Authorised Service Engineer of OEM or OEM Certified Agencies will carry out all breakdown maintenance after receiving information (written or oral) from GE kalaikunda officials or their representatives.The OEM's authorised service representative or OEM certified agencies will carry out the required repairs of the units and appraise GE, Engineer-in-Charge and JE the status of the break down repair at site. No payment shall be made on account of any breakdown service to the machinary/equipments during comprehensive maintenence period. (viii) The Service Engineer will be called in case of any breakdown and the same shall be attended within 24 Hours of lodging of complaint, failing which a penal recovery of Rs.200.00 (Rupees Two Hundred Only) per day till such time the unit is attended and complaint is resolved,will be recovered from the outstanding dues to the Contract (vi) Cost of minor items like insulating tape,gland packing materials, metal washers, fibre/rubber washers, screws, small nuts & bolts and like shall be deemed to be inclusive of the quoated rate.

Supply & fix Rotor shaft with couplings and seals of submersible motor of capacity 7.5 HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

M&L for replacement of thrust bearing as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE for Submersible motor of capacity 7.5HP complete as specified and directed [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix Impeller of submersible motor of capacity of 7.5HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix diffuser of submersible motor of capacity of 7.5HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix neck ring of submersible motor of capacity 7.5HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix stud nut of submersible motor of capacity of 7.5HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

All as per item No 27 above herein before but submersible pump set capacity of 15HP complete all as specified and directed .

Supply & fix Rotor shaft with couplings and seals of submersible motor of capacity 15 HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix thrust bearing of submersible motor of capacity of 15HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix Impeller of submersible motor of capacity of 15HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix diffuser of submersible motor of capacity of 15HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix neck ring of submersible motor of capacity 15HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix stud nut of submersible motor of capacity of 15HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

All as per item No 27 above herein before but submersible pump set capacity of 20HP complete all as specified and directed .

Supply & fix Rotor shaft with couplings and seals of submersible motor of capacity 20 HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix thrust bearing of submersible motor of capacity of 20HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix Impeller of submersible motor of capacity of 20HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix diffuser of submersible motor of capacity of 20HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix neck ring of submersible motor of capacity 20HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Supply & fix stud nut of submersible motor of capacity of 20HP as per Original Equipment Manufacturer's (OEMs) reccommendations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Comprehensive maintenance as per Original Equipment Manufacturer's (OEMs) reccommendations for a period of nine months for 7.5 HP capacity 3- phase, 415 volts, 50 Hz Openwell submersible /Monoblock pump sets installed at various locations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE, and including rewinding of burnt Openwell submersible /Monoblock motor 7.5 HP , 3 phase ,415 V, 50 Hz of any make with water proof insulated copper conductor of the same specification as per old one after dismantling / cutting out burnt windings from stator assembly, cleaning slots properly complete with insulating slots packing, sleeves, papers & reassembling stator and rotor after replacement of worn out spares/matching works including painting with two coats of synthetic enamel paint over a coat of red oxide primer after preparation of motor external surface complete all as specified and directed. [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Comprehensive maintenance as per Original Equipment Manufacturer's (OEMs) reccommendations for a period of nine months for 5 HP capacity 3- phase, 415 volts, 50 Hz Openwell submersible /Monoblock pump sets installed at various locations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE,and including rewinding of burnt Openwell submersible /Monoblock motor 5 HP , 3 phase ,415 V, 50 Hz of any make with water proof insulated copper conductor of the same specification as per old one after dismantling / cutting out burnt windings from stator assembly, cleaning slots properly complete with insulating slots packing, sleeves, papers & reassembling stator and rotor after replacement of worn out spares/matching works including painting with two coats of synthetic enamel paint over a coat of red oxide primer after preparation of motor external surface complete all as specified and directed. [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Comprehensive maintenance as per Original Equipment Manufacturer's (OEMs) reccommendations for a period of nine months for 3 HP capacity 3- phase, 415 volts, 50 Hz Openwell submersible /Monoblock pump sets installed at various locations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE,and including rewinding of burnt Openwell submersible /Monoblock motor 3 HP , 3 phase ,415 V, 50 Hz of any make with water proof insulated copper conductor of the same specification as per old one after dismantling / cutting out burnt windings from stator assembly, cleaning slots properly complete with insulating slots packing, sleeves, papers & reassembling stator and rotor after replacement of worn out spares/matching works including painting with two coats of synthetic enamel paint over a coat of red oxide primer after preparation of motor external surface complete all as specified and directed. [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Comprehensive maintenance as per Original Equipment Manufacturer's (OEMs) reccommendations for a period of nine months for 2 HP capacity 3- phase, 415 volts, 50 Hz Openwell submersible /Monoblock pump sets installed at various locations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE,and including rewinding of burnt Openwell submersible /Monoblock motor 2 HP , 3 phase ,415 V, 50 Hz of any make with water proof insulated copper conductor of the same specification as per old one after dismantling / cutting out burnt windings from stator assembly, cleaning slots properly complete with insulating slots packing, sleeves, papers & reassembling stator and rotor after replacement of worn out spares/matching works including painting with two coats of synthetic enamel paint over a coat of red oxide primer after preparation of motor external surface complete all as specified and directed. [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/]

Comprehensive maintenance as per Original Equipment Manufacturer's (OEMs) reccommendations for a period of nine months for 1 HP capacity 3- phase, 415 volts, 50 Hz Openwell submersible /Monoblock pump sets installed at various locations through OEMs Authorised Service Centre Engineers or through OEMs Certified Agencies as approved by GE,and including rewinding of burnt Openwell submersible /Monoblock motor 1 HP , 3 phase ,415 V, 50 Hz of any make with water proof insulated copper conductor of the same specification as per old one after dismantling / cutting out burnt windings from stator assembly, cleaning slots properly complete with insulating slots packing, sleeves, papers & reassembling stator and rotor after replacement of worn out spares/matching works including painting with two coats of synthetic enamel paint over a coat of red oxide primer after preparation of motor external surface complete all as specified and directed. [Make: Calama/Kriloskar/CRI/KSB/Crompton Greaves/] NOTES:- (Applicable for BOQ Serial Item No. 48 to 52 here in before) (i) The Contractor shall provide the following comprehensive services arising out of wear and tear of the normal running of Pump Sets (ii) Preventive and Corrective Maintenance : The authorised Service Engineer of OEM or OEM Certified agencies shall visit the site once quarterly for carrying out preventive and corrective maintenance on all the units installed at site. This includes maintenance of all mechanical, electrical parts / sub-assemblies. The preventive maintenance report will be as per the Original Equipment Manufacturer's instructions and as specified in Particular Specification. The Contractor may claim payment on monthly basis. In that case the payment shall be made with pro-rata basis on quoted rates. (iii) Breakdown Maintenance : The Authorised Service Engineer of OEM or OEM Certified Agencies will carry out all breakdown maintenance after receiving information (written or oral) from GE kalaikunda officials or their representatives.The OEM's authorised service representative or OEM certified agencies will carry out the required repairs of the units and appraise GE, Engineer-in-Charge and JE the status of the break down repair at site. No payment shall be made on account of any breakdown service to the machinary/equipments during comprehensive maintenence period. (iv) OEMs Authorised Service Centre Engineers or OEMs Certified Agencies shall visit once in a month for routine inspection and general maintenance. (v) The Service Engineer will be called in case of any breakdown and the same shall be attended within 24 Hours of lodging of complaint, failing which a penal recovery of Rs.500.00 (Rupees FIve Hundred Only) per day till such time the unit is attended and complaint is resolved,will be recovered from the outstanding dues to the Contractor. (vi) Cost of minor items like insulating tape,gland packing materials, metal washers, fibre/rubber washers, screws, small nuts & bolts and like shall be deemed to be inclusive of the quoted rate. (vii) Spares required for replacement of defective will be deemed to be included in quoated rates. (viii) The Contractor shall maintain service reports for all visits & breakdown visits & copy of the same will be submitted for every quarter to the Engineer in Charge.

M&L for Flushing of tube well bore with compressed air by using air compressor for pumping muddy water continuously 8 Hrs without break complete as directed by Engr-in-Charge. Note:- Compressor of CFM with minimum 10 Kg/ cm² pressure to be used for flushing.

M&L for motor foundation channel, clamps, back plates and shed fabricated from structural steel sections, sheets including nuts, bolts, washers, welding, cutting, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all and taking out old u/s foundation channel all as specified and directed by Engr-in-Charge.

Supply and Fix in repairs,moulded case circuit breakers (MCCBs),conforming to IEC 60947-2& IEC 60947-2, AC 415V, 4 pole, with current rating 125 Amps and 25 KA breaking capacity Icu at 415V, AC, 50Hz, with adjustable Over Load setting: 0.8 - 1.0 x In and adjustable Short Circuit setting: 6-10 x In, complete all as specified and directed. [Cat No. CM90642OOLO of Make “L&T” or equivalent Model of Make Siemens/ Legrand / ABB.]

Materials and Labour for plain cement concrete (1:3:6) Type C-2 using 40 mm graded aggregate in foundations, filling and mass concrete including demolition of cement concrete complete all as specified and directed.

Materials and Labour for rendering 10 mm thick, cement plaster, in cement mortar (1:4) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr in depth in any type of soil and getting out for taking up/laying of GI/PPR/CI pipes all as specified and directed . Note : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick all as directed

Removal of surplus soil to a distance n.exc 50 mtrs and deposited where directed at a level n.exc1.5 mtr above the starting point all as specified and directed .

Horizontal boring of holes, under road/ pavement / hard standing etc.,not exceeding 10 Metres in length, in any type of soil, suitable for passing through 20mm to 80 mm bore, galvanised steel tubing,complete all as specified and directed.

Taking out old unserviceable GI/PVC/PPR pipes from trenches, walls, floors, ceiling and duct etc including all fittings of 80 mm bore complete all as specified and directed by Engr-in charge. Note: Excavation/earth work will be measured and paidseparately under relevent item of BOQ.

All as per item No. 62 above herein before but of size 50 mm bore complete all as specified and directed.

All as per item No 62 above herein before but of size 40 mm bore complete all as specified and directed.

All as per item No 62 above herein before but of size 25 mm bore complete all as specified and directed.

All as per item No 62 above herein before but of size 20 mm bore complete all as specified and directed.

All as per item No 62 above herein before but of size 15 mm bore complete all as specified and directed.

Material and labour for laying of GI tubing 80 mm bore, medium grade, , galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete like elbow, socket, tee, reducer, nipple, short piece, union etc as required at site and laid in trenches incl connecting with existing lines complete all as specified and directed. Note: (i) Union or long screw have to provided at starting / end point of jointing pipe line . (ii) Contractor has to submit the test certificate and purchase voucher of pipes before claiming payment.

All as per item No 68 above herein before but of size 50 mm bore complete all as specified and directed

All as per item No 68 above herein before but of size 40 mm bore complete all as specified and directed

All as per item No 68 above herein before but of size 25 mm bore complete all as specified and directed

All as per item No 68 above herein before but of size 20 mm bore complete all as specified and directed

All as per item No 68 above herein before but of size 15 mm bore complete all as specified and directed

Supplying & fixing to walls and ceiling 25 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed. Note: (i) Union or long screw have to provided at starting / end point of jointing pipe line . (ii) Contractor has to submit the test certificate and purchase voucher of pipes before claiming payment. (iii) Contractor shall provide MS/GI clamp for fixing the pipe on wall on every 20 cm without any extra cost.

All as per item No 74 above herein before but of size 20 mm bore complete all as specified and as directed.

All as per item No 74 above herein before but of size 15 mm bore complete all as specified and as directed.

All as per item No 74 above herein before but of size 40 mm bore complete all as specified and as directed.

M&L for 3 layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot / cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall ceilings or in floors/ fixed on wall in surface etc complete all as specifed and directed by Eng In Charge of following sizes :. Note : (i) All T&P required for fixing and for making fusion joint of pipe shall be provided by contractor without any extra cost. (ii) Proper clamping to be done of every 30 cm for fixing the pipe on wall/ floor/ ceiling. (a) 16 mm outer diameter of pipe

All as per item No 78 above herein before but of size 20 mm bore complete all as specified and as directed.

All as per item No 78 above herein before but of size 25 mm bore complete all as specified and as directed.

M&L for refixing existing old GI/PVC/PPR pipe for 50 mm bore of pipe including taking down under respective item above in new or existing position after cleaning and providing new GI fitting complete all as specifed and directed Note: Union or long screw have to provided at starting / end point of jointing pipe line .

All as per item No 82 above herein before but of size 40 mm bore complete all as specifed and directed

All as per item No 82 above herein before but of size 25 mm bore complete all as specifed and directed

All as per item No 82 above herein before but of size 20 mm bore complete all as specifed and directed

All as per item No 82 above herein before but of size 15 mm bore complete all as specifed and directed

Material and labour for fixing GM globe/gate valve 50 mm bore with iron wheel head, screwed both ends for iron/PPR pipes, ISI marked, conf to IS including taking down old complete all as specified and directed by Engr in charge. Make : ZOLOTO / LEADER/ KARTAR. Note: Union or long screw have to provided before fixing of gate valve. (ii) Contractor has to submit the test certificate and purchase voucher of valves before claiming payment.

All as per item No 87 above but of size 40 mm bore complete all as specified and directed

All as per item No 87 above but of size 25 mm bore complete all as specified and directed

All as per item No 87 above but of size 20 mm bore complete all as specified and directed

All as per item No 87 above but of size 15 mm bore complete all as specified and directed

Material and labour for fixing PPR Gate valve (brass insert) of 40 mm outer dia with iron wheel head, screwed both ends for iron/PPR pipes, including taking down old complete all as specified and directed by Engr in charge. Note: Union or long screw have to provided before fixing of gate valve.

Material and labour for fixing PPR Gate valve (brass insert) of 25 mm outer dia with iron wheel head, screwed both ends for iron/PPR pipes, including taking down old complete all as specified and directed by Engr in charge. Note: Union or long screw have to provided before fixing of gate valve.

Material and labour for fixing PPR Gate valve (brass insert) of 20 mm outer dia with iron wheel head, screwed both ends for iron/PPR pipes, including taking down old complete all as specified and directed by Engr in charge. Make :SFC ZOLOTO Note: Union or long screw have to provided before fixing of gate valve.

Taking down unserviceable sluice valve/ Butter fly vlave/ NRV/foot valve and their fitments like gasket , bolt/nuts of size 80 to 300 mm bore without damaging the valve chamber and pipe line complete all as specified and directed by Engineer-In-charge

Supply and fixing sluice valve 300 mm bore, ISI marked, as per IS 14846: 2000 , with valid CMLNo. , Batch No. and Manufacturer Serial No., class PN 1.6 with brass spindle, brass check nut, with fiber board gasket, bolts, nuts and washers for fixing the valve in position, in valve pit chambers or location as directed and specified by Engr-in-charge. Make Uphadhya / Kirloskar/ Leader Note : Contractor has to submit the test certificate and Purchase Voucher of valves before claiming the payment..

Supply and fixing sluice valve 250 mm bore, ISI marked, as per IS 14846: 2000 , with valid CMLNo. , Batch No. and Manufacturer Serial No., class PN 1.6 with brass spindle, brass check nut, with fiber board gasket, bolts, nuts and washers for fixing the valve in position, in valve pit chambers or location as directed and specified by Engr-in-charge. Make Uphadhya / Kirloskar/ Leader Note : Contractor has to submit the test certificate and Purchase Voucher of valves before claiming the payment..

Supply and fixing sluice valve 200 mm bore, ISI marked, as per IS 14846: 2000 , with valid CMLNo. , Batch No. and Manufacturer Serial No., class PN 1.6 with brass spindle, brass check nut, with fiber board gasket, bolts, nuts and washers for fixing the valve in position, in valve pit chambers or location as directed and specified by Engr-in-charge. Make Uphadhya / Kirloskar/ Leader or equivalent make as catered in PS Note : Contractor has to submit the test certificate and Purchase Voucher of valves before claiming the payment..

Supply and fixing sluice valve 150 mm bore, ISI marked, as per IS 14846: 2000 , with valid CMLNo. , Batch No. and Manufacturer Serial No., class PN 1.6 with brass spindle, brass check nut, with fiber board gasket, bolts, nuts and washers for fixing the valve in position, in valve pit chambers or location as directed and specified by Engr-in-charge. Make Uphadhya / Kirloskar/ Leader or equivalent make as catered in PS Note : Contractor has to submit the test certificate and Purchase Voucher of valves before claiming the payment..

Supply and fixing sluice valve 100 mm bore, ISI marked, as per IS 14846: 2000 , with valid CMLNo. , Batch No. and Manufacturer Serial No., class PN 1.6 with brass spindle, brass check nut, with fiber board gasket, bolts, nuts and washers for fixing the valve in position, in valve pit chambers or location as directed and specified by Engr-in-charge. Make Uphadhya / Kirloskar/ Leader or equivalent make as catered in PS Note : Contractor has to submit the test certificate and Purchase Voucher of valves before claiming the payment.

Supply and fixing sluice valve 80 mm bore, ISI marked, as per IS 14846: 2000 , with valid CMLNo. , Batch No. and Manufacturer Serial No., class PN 1.6 with brass spindle, brass check nut, with fiber board gasket, bolts, nuts and washers for fixing the valve in position, in valve pit chambers or location as directed and specified by Engr-in-charge. Make Uphadhya / Kirloskar/ Leader or equivalent make as catered in PS Note : Contractor has to submit the test certificate and Purchase Voucher of valves before claiming the payment..

Supply and fixing in repair Cast Iron Butterfly valve of 150 mm dia , wafer type , SS disc, PN 1.0 ISI marked, as per IS 13095: 1991,both end flanged including fiber board gasket, bolts, nuts and washers for fixing the valve in position, or location as directed and specified . Make : ZOLOTO / LEADER/ KARTAR.

Supply and fixing in repair Cast Iron Butterfly valve of 100 mm dia , wafer type , SS disc, PN 1.0 ISI marked, as per IS 13095: 1991,both end flanged including fiber board gasket, bolts, nuts and washers for fixing the valve in position, or location as directed and specified .. Make : ZOLOTO / LEADER/ KARTAR.

Supply and fixing in repair Non return (Reflux valve) 150 mm dia , flap type ISI marked,as per IS 13095: 1991,both end flanged including fiber board gasket, bolts, nuts and washers for fixing the valve in position, or location as directed and specified by Engr-in-charge . Make : Uphadhya / Kirloskar/ Leader

Supply and fixing in repair Non return (Reflux valve) 100 mm dia , flap type ISI marked,as per IS 13095: 1991, both end flanged including fiber board gasket, bolts, nuts and washers for fixing the valve in position, or location as directed and specified by Engr-in-charge .Make :Uphadhya / Kirloskar/ Leader

Supply and fixing flexible coupling (Mechanical Joint) leakeproof of size 150 mm , ISI marked , long body all as specified by EIC . Make : RMCO or equivalent make as approved by GE. Note Contractor shall produce the sample before procurement of item.

Supply and fixing flexible coupling (Mechanical Joint) leakeproof of size 100 mm , ISI marked , long body all as specified by EIC . Make : RMCO or equivalent make as approved by GE. Note :- Contractor shall produce the sample before procurement of item.

Supply only flexible coupling (Mechanical Joint) leakeproof of size 80 mm , ISI marked , long body all as specified by EIC . Make : RMCO or equivalent make as approved by GE. Note :- Contractor shall produce the sample before procurement of item.

Material and labour for run lead joints for connecting of the CI pipes of 300 mm dia of pipe including jointing materials and including burning out lead joints complete all as specified and directed.

Material and labour for run lead joints for connecting of the CI pipes of 250 mm dia of pipe including jointing materials and including burning out lead joints complete all as specified and directed.

Material and labour for run lead joints for connecting of the CI pipes of 200 mm dia of pipe including jointing materials and including burning out lead joints complete all as specified and directed.

Material and labour for run lead joints for connecting of the CI pipes of 150 mm dia of pipe including jointing materials and including burning out lead joints complete all as specified and directed.

Material and labour for run lead joints for connecting of the CI pipes of 100 mm dia of pipe including jointing materials and including burning out lead joints complete all as specified and directed.

Material and labour for run lead joints for connecting of the CI pipes of 80 mm dia of pipe including jointing materials and including burning out lead joints complete all as specified and directed.

Taking down old unserviceable CI pipe line from trench/ floor any location of size 80 mm to 300 mm bore with including spigot socket ends and lead/tyton joints including burning out lead joints and recovering lead of the following size of pipe for reuse complete all as specified and as directed.(Note : serviceable pipes and fittings shall be stack at site properly for reuse and unserviceable pipes shall be removed from work site)

Supply and laying of Cast iron pipe (CI) with spigot and socket end suitable for and including tighten joint of dia 150 mm size centrifugally cast class "B" in any length laid in trenches complete all as specified and directed. Note :- Excavation and earth work will be measured and paid separately under relevant item of sch A. .

Supply and laying of Cast iron pipe (CI) with spigot and socket end suitable for and including tighten joint of dia 100 mm size centrifugally cast class "B" in any length laid in trenches complete all as specified and directed. Note :- Excavation and earth work will be measured and paid separately under relevant item of sch A. .

Supply and laying of Cast iron pipe (CI) with spigot and socket end suitable for and including tighten joint of dia 80 mm size centrifugally cast class "B" in any length laid in trenches complete all as specified and directed. Note :- Excavation and earth work will be measured and paid separately under relevant item of sch A. .

Materials and Labour for, cast iron fittings for spigot and socketed cast iron pipes for water mains upto 150 mm bore,such as Bends (any type, radius and angle) tapers any type, (straight, bend, increasing,decreasing or double socket etc.) Tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs, complete all as specified and directed.

S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in framed work such as grills, grating, etc., with ends of bars of shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework water tanks and similar work complete all as specified and directed by Engineer-in-charge.

Supply and fix in repair water level indicator made of aluminium base, marked with white Radium paint connected with steel wire rope 4 mm dia to counter weight showing level of water containing in tank including 8" dia brass float ball , and greasing of revolving pully of as per site requirement and fixed to pillar of water tank complete all as specified and directed by Engr-in-Charge Note : (i) All T&P required at site for fixing water level indicator on over head Tank at 18/21 mtr height shall be arranged by contractor (ii) To remove the Bee Hives for fixing the guadge on water tank of height 18/21 mtr shall be contractor responsbility with any extra cost.

Supply only synthethic enamel paint SKY Blue colour , high glossy finish, of Make Asian Apcolite rust shield , Anti rust shield PU enamel , having quick drying time, no primer requirement, with 2 year warranty . Make Asian Paints (Apcolite rust shield) or equivalent in Narolac

Supply only synthethic enamel paint Yellow colour , high glossy finish, of Make Asian Apcolite rust shield , Anti rust shield PU enamel , having quick drying time, no primer requirement, with 2 year warranty . Make Asian Paints (Apcolite rust shield) or equivalent in Narolac

Supply only synthethic enamel paint Red colour , high glossy finish, of Make Asian Apcolite rust shield , Anti rust shield PU enamel , having quick drying time, no primer requirement, with 2 year warranty . Make Asian Paints (Apcolite rust shield) or equivalent in Narolac

Supply only synthethic enamel paint leave Green colour , high glossy finish, of Make Asian Apcolite rust shield , Anti rust shield PU enamel , having quick drying time, no primer requirement, with 2 year warranty . Make Asian Paints (Apcolite rust shield) or equivalent in Narolac

Supply only synthethic enamel paint Black colour , high glossy finish, of Make Asian Apcolite rust shield , Anti rust shield PU enamel , having quick drying time, no primer requirement, with 2 year warranty . Make Asian Paints (Apcolite rust shield) or equivalent in Narolac

Supply only Soft Board Notice board of Green colour valvet Cloth , rectangle board of size 900 x 1200 mm made with aluminium frame material and having core material thickness of more than or equal to 9 mm in Blue/ green/red colour with hooks to hange it on wall . Make : Alko Sign

M&L for repair of mechanical water level indicator fixed of RCC overhead tank of height 18/25 mtr including replacement of unserviceable GI rope, level indicator, brass/ steel float, pulley, greasing the moving parts etc and any other material required at site to make the water level indicator functional complete all as specified and directed by Eng in Charge Note : (i) Spare parts of indicator like pulley, float , GI wire to be paid seperately as mentoned below here in after relevant items of BOQ. (ii) All T&P required at site for making the water level indicator functional and safety arrangement of his technician deployed for the Job shall be contractor responsibility with out any extra cost. (iii) Contractor shall be responsible to make the level indicator functional and if the rope slips from pulley and indicator become unfunctional during currency of contract, the contractor shall re do the work without any extra cost.

Supply only GI wire rope of 3 mm dia as per existing specification for water level indicator complete all as specified and directed.

Supply only Pully as per existing specification and size complete all as specified and directed.

Supply only Stain less steel float as per existing speciifcation and size suitable for water level indicator of water tank of 1.30 LG / 1.10 LG complete all as specified and directed.

Supply only Stain less steel float as per existing speciifcation and size suitable for water level indicator of water tank of capacity 0.60 LG complete all as specified and directed.

M & L for cement concrete in foundation, filling and mass concrete in M10(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate including demolition cement concrete of any description complete all as specified and as directed.

M & L for cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs, slab staging for water tanks and the like including weathering, slightly rounded or chamfered angles and throating including necessary formworks complete all as specified and directed by Engineer- in-charge.

M & L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4 including demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed by Engineer in charge

M & L for cleaning and washing of inside portion of RCC Overhead Water Tank of Round/ Square type up to 25 mtr height , of capacity 1.30 lakhs gallons located in domestic area, with Anti-bacterial agent consisting of following process: - Dewatering the tank by mechanical means as directed, de-silting and removing of left over dirty water up to 100 to 150 mm in the bottom of the tank and sludge with special sludge pump, cleaning of walls and ceiling with special mechanized high pressure jet machines by rotary jet system at 100-120 Bar pressure (120 Kg /sq cm) which dislodges the layer of dirt, algae, fungus stuck on its surface usage of scrubbing machines for old stains and cleaning chemicals if required of make Eureka Forbes Ltd or equivalent as approved by GE, floor of the dirty tank should be thoroughly cleaned up by fry jet cleaner to accumulate all dirt ,the remaining sludge should than be removed by sludge pumps, the dirt silt and other foreign material should further be removed by Industrial Vacuum Cleaners to make the floor totally dirt free, application/spraying of Anti-Bacterial chemicals to ensure total sterilization of tank from the inside, inside of the tank should be treated with specially developed 4 ft long ultraviolet Radiator to kill further floating bacteria/virus in order to make the tank totally clean, bacteria free and safe for storage of drinking water. All the above operations should be executed by trained workers and technicians, properly dressed along with gum boots, to work as per the direction of Engineer in charge. and writing "Date of cleaning and Next due date of cleaning" on the column of tank at specified location with and including necessarry scalfolding and safety measure complete all as specified and directed.

All as per item No. 136 here-in-before but capacity 1.10 lakhs gallons, complete all as specified and as directed

All as per item No. 136 here-in-before but capacity 60000 gallons, complete all as specified and as directed

All as per item No. 136 here-in-before but capacity 25000 gallons at technical area, complete all as specified and as directed

All as per item No. 136 here-in-before but capacity 15000 gallons at technical area, complete all as specified and as directed

All as per item No. 136 here-in-before but capacity 0.20 lakh gallons RCC under ground water tank / Reservior of Round/ Square type at technical area, complete all as specified and as directed

All as per item No. 136 here-in-before but capacity 0.25 lakh gallons RCC under ground water tank / Reservior of Round/ Square type at technical area, complete all as specified and as directed

All as per item No. 136 here-in-before but capacity 0.30 lakh gallons RCC under ground water tank / Reservior of Round/ Square type at technical area, complete all as specified and as directed Note for item No. 136 to 143 : (i) Removing of bee heavs and cleaning of vegitation grown on tank shall be done by the contractor without any extra charge. (ii) All T&P required at site for cleaning of tank shall be arranged by the contractor without any extra cost.. (iii) All safety measures, safety belts, helments and other safety tools required at site for the trademens deployed for cleaning of tanks (under ground and over head RCC tanks) shall be provided by the contractor without any extra cost. (iv) Contractor has to clean the tank after tanking permission from Eng in Charge in one week advance. (v) Contractor shall use dewatering pump and industrial vaccume cleaner for cleaning of tank. (vi) Contractor shall deploy sufficient labour for cleaning the tank with stipulate time period of same day so that water supply from that tank would not be hampered. (vii) Contractor has to submit the photos of inside tank before cleaning and after cleaning to the Eng in Charge before claiming for payment. (viiii) Contractor shall provide ACP sheet of size 400 mm x 400 mm on each tank for writing date of cleaning of tank and next due date of cleaning on blue base with white colour. (IX) It is mandatory that contractor shall submit the insurance certificate minimum 10 Lakh sum assured of all staff/employee employed by him for the above mentioned works.

Drilling and tapping DI/CI/GI water mains pipeline (in position) for branch connections of the internal dia of 15 mm all as specified and as directed by Engr-in-Charge.

Drilling and tapping DI/CI/GI water mains pipeline (in position) for branch connections of the internal dia of 20 mm all as specified and as directed by Engr-in-Charge.

Supply and fixing Straight plain brass ferrules (or connecting screws) screwed both ends of dia 15 mm all as specified and as directed by Engr-in-Charge.

Supply and fixing Straight plain brass ferrules (or connecting screws) screwed both ends of dia 20 mm all as specified and as directed by Engr-in-Charge.

Supply and fixing Bib tap standard of PTMT white colour high pressure screwed for iron pipe and fixed of size 20mm dia (Minimum weight 20mm-125 gms) all as specified and as directed by Engr-in-Charge.

Supply and fixing Bib tap standard of PTMT White colour, high pressure screwed for iron pipe and fixed of size 15mm dia (Minimum weight 15mm-90gms) all as specified and as directed by Engr-in-Charge.

Supply and Fix in repairs,ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe 20 mm bore and fixed (Minimum weight 210 grams), complete all as specified and directed. [Make: Prayag Polymer Pvt Ltd Cat No.152 or equivalent Model of Make RS Industries: Polytuf/ Microplast Polymers Pvt Ltd]

Supply and Fix in repairs,ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe 25 mm bore and fixed (Minimum weight 455 grams), complete all as specified and directed. [Make: Prayag Polymer Pvt Ltd Cat No.153 or equivalent Model of Make RS Industries:Polytuf/ Microplast Polymers Pvt Ltd]

Material and labour for lead wool joints for connecting of the CI pipes of size 100 mm bore complete all as specified and directed by Engr-in-Charge.

Material and labour for lead wool joints for connecting of the CI pipes of size 150 mm bore complete all as specified and directed by Engr-in-Charge.

S & F rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 300 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including 20mm bore float valve all as specified and as directed.

S & F rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 500 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including 20mm bore float valve all as specified and as directed.

S& F in repair Pressure guage, Anolog type , 150 mm dia, aluminium bottom capable of showing up to 8 Kg/cm2 pressure including taking down u/s complete all as specified and directed by Engineer in Charge

S& F Pressure guage cock to control water flow including taking down unserviceable one complete all as specified and directed by Engineer in Charge

S& F in repair suction sweeper head (pool cleaner) 36 " long complete with wheel, nylon brush, NRV etc complete all as specified and directed by Engineer in Charge

S& F in repair wood core nylon brush 36 " long for sweeper (pool cleaner) complete all as specified and directed by Engineer in Charge

S& F in repair replacement of gasket of MS /CI/GI pipe flange joint of 150 mm dia, with new rubber or fiber board gasket including replacement of nut bolts and washer complete all as specified and directed by Eng in charge.

S& F in repair replacement of gasket of MS /CI/GI pipe flange joint of 100 mm dia, with new rubber or fiber board gasket including replacement of nut bolts and washer complete all as specified and directed by Eng in charge.

S& F in repair replacement of gasket of MS /CI/GI pipe flange joint of 80 mm dia, with new rubber or fiber board gasket including replacement of nut bolts and washer complete all as specified and directed by Eng in charge.

Supply only of rubber sheet of min 3 mm thickness for use in jointing sulice valves with flange etc complete all as specified and directed by Eng in charge.

Supply only of MS nut bolt and washer of size as specified complete all as specified and directed by Eng in charge.

S& F in repair replacement of Foot valve with Gun metal working part, conf to ISS 4038 with strainer including replacement of nut bolts and washer complete all as specified and directed by Eng in charge.

Supply only Flexible medium duty PVC / delivery hose pipe, sprial ribbed, green colour , working pressure 3.5 Kg / Sq cm of nominal bore 40 mm and metallic clamp 4 Nos complete all as specified and directed by Eng in charge.

Supply only Flexible medium duty PVC / delivery hose pipe, sprial ribbed, green colour , working pressure 3.5 Kg / Sq cm of nominal bore 25 mm and metallic clamp 4 Nos complete all as specified and directed by Eng in charge.

Supply only WD-40, multipurpose spray for rust removal of capacity 420 ml complete all as specified and as directed by Engr-in-Charge.

Supply only short piece MS pipe heavy duty, min thickness 6 mm, of min length 1.0 mtr, 100 mm dia having one end welded and screwed with MS flange having 4 or 8 hole and grove for passing of submersible cable and wire rope and other side with thread end having 8 pitch complete all as specified and directed

Supply only short piece MS pipe heavy duty, min thickness 6 mm, of min length 1.0 mtr, 100 mm dia having one end welded and screwed with MS flange having 4 or 8 hole and grove for passing of submersible cable and wire ropeand other side with thread end having 11 pitch complete all as specified and directed

Supply only MS reducer socket of size 150 mm x 100 mm dia having internal thread on 100 mm side and external thread on 80 mm side complete all as specified and directed

Supply only MS reducer socket of size 150 mm x 80 mm dia having internal thread on 100 mm side and external thread on 80 mm side complete all as specified and directed

Supply only MS reducer socket of size 100 mm x 80 mm dia having internal thread on 100 mm side and external thread on 80 mm side complete all as specified and directed

Supply only MS reducer socket of size 100 mm x 50 mm dia having internal thread on 100 mm side and external thread on 50 mm side complete all as specified and directed

Supply only MS reducer socket of size 80 mm x 50 mm dia having internal thread on 80 mm side and external thread on 50 mm side. complete all as specified and directed

Supply only GI reducer socket of size 150 mm x 100 mm complete all as specified and directed

Kalpana Traders