Loading…
Loading…
Updated dates
Tender Value
₹15.4 L
EMD Value
₹30,740
Closing Date
11 Jun 2026, 1:00 pm6d left
EE-II KNHED PWDte.
KIT Building Annex, 4thFloor,P-16, India Exch. Place Extn., Kolkata -700073
Enhancing Built environment accessibility for person with disabilities under Accessible India Campaign (Sugamya Bharat Abhiyan) in Bio- Chemistry Building within the campus of MCH, Kolkata ---- Electrical Installation Work---- Part (A) SITC of Lift
2026_WBPWD_5013958_1
WBPWD/EE-II/KNHED/NIQ-79/2nd Call/ 2025-26
Open Tender
ELECTRICAL WORKS ORG
60 days
Kolkata
Please refer Tender documents.
6 documents required · 6 mandatory
₹30,740
OFFICE OF THE EE KNHED PWDte.
12 May 2026
12 May 2026
15 Jun 2026
12 May 2026
11 Jun 2026
19 May 2026
18 May 2026
10-PASSENGER LIFT - WITHOUT MACHINE ROOM SITC of Automatic Lift ( as per manufacturer design & as per detailed specification below conforming to IS ) and putting into operation after final testing in the existing lift shaft complete with all accessories and repairing the damage wall / floor if any etc to complete as reqd.
Make : OTIS / KONE/SCHINDLER
Type: passenger Lift .
Load : 10Passenger/680Kg
Control : Microprocessor based with AC variable voltage & variable frequency ( VVVF) (Simplex Full Collective Control)
Machine -- Energy efficient machine, Gearless, with Out Machine Room. [ MRL]
Position of Machine Room - NA
Speed:- 1Mtrs/Sec
Floor served :- G+2
Landing: 03 (Three), all on same side
Total Rise -9.8Mtr
Operation : Microprocessor based simplex full collective with or without attendant. (Simplex Full Collective Control)
Signals : Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator. Buttons: all buttons on car & landing shall be luminous & encoded with braille
Leveling accuracy : ±5mm Micro levelling arrangement
Car inside : -1300 mm wide x 1350 mm deep x 2200 mm high
Car Entrence : Clear opening 800mm (W) x 2000mm (H) protected with car door.
Car Encloser : Stainless Steel Sheet (20 SWG) with hairline finish with hand rail. (Stainless steel Hairline AISI441)
Car ceiling & Lighting : Stainless steel with hairline finish with LED lighting & fan
Car Ventilation- Pressure fan with anodized aluminium grill.
Car Flooring: Decorative granite flooring (As per direcion of EIC and according to this Department's Order).
Car Door : Stainless Steel centre opening automatic door (COPD) provided with V3F controlled door drive system
Landing Door- Stainless steel centre opening door operated synchronizing with car door. Two-panel centre opening Plain Panel.
Door Opening - Automatic power oprated door with full length PhotoceL assembly light curtain sensor
PROTECTIVE DEVICES & OTHER ACESSORIES
ARD- Automatic rescue device complete with dry maintenance free batteries as required. for automatic evacuation to the nearest floor in case of power failure / single phasing/others.
Overload Protection -Fully loaded with overload protection. On overloading the lift car will not start with door remaining open and give audio & display indication
Emergency lighting in car- Battery operated emergency lighting in the lift car.
Intercom system : Battery operated intercom system in Lift Car, Machine Room & Control Room
Emergency Alarm: Battery operated alarm bell system in lift car and control room
Fireman switch - Fireman switch at main landing terminal.
Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator.
Main rope/Belt - As per manufacturer's standard conforming to IS
DIMENSION OF SHAFT & POWER SUPPLY
Available Shaft Dimension 1900 mm (Wide) X 1680mm(Depth)
Pit Depth : 1600mm
Overhead : 4500 mm
Electric power supply AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS
N.B. i) The rate quoted by the manufacturer should be inclusive of cost for providing 2 years DLP after completion of 1 year of intial commissioning
ii) Rates should be quoted with minor Civil works. Wall cutting and mending good the damages to the original finish.
Terms and Conditions i) The Agency must procure the materials from the Manufacturer / OEM or from their authorise sales channel so that the standard warranty / Supportof of the Manufacturer / OEM becomes applicable to the products to be delivered and installed by them. ii) Documents that authenticates such procurement from the Manufacturer / OEM or from their authorized sales channel and standard warranty / support should be sent from the e-mail of the Manufacturer / OEM / authorized sales channel to the e-mail of Engineer-in-Charge and hard copy of it to be submitted during execution of work /submission of bill iii) If any refurbished material is supplied and installed penal action will be taken as per existing rules.
[ Rates should be Quotated inclusive of all taxes & duities and L.W.C. @ 1% as applicable ]
Please Enable Macros to View BoQ information
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.50 MB
BOQ_5081857.xls
BOQ • 0.35 MB
2911.pdf
Tender Documents • 1.46 MB
suspension.pdf
Additional Documents • 2.91 MB
Download all tender documents and submit your bid