PROVN OF TOILETS INCLUDING STORE ROOM AND DRAINAGE SYSTEM AT PRIMARY WING OF NCS (KAR) AT KADAMBA VANAM AND ADDITIONS / ALTERATION AND SPECIAL REPAIRS TO BLDG NO P- 06 AT KAMAT BAY AT NAVAL BASE KARWAR UNDER GE (SB) KARWAR

Amount

M&L for surface dressing not exceeding 15 cm deep in hard/dense soil, complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for foundations, etc., and getting out in hard/dense soil, complete all as specified and directed.

M&L for PCC 1:4:8, type D-2, using 40 mm graded stone aggregate as in foundation filling and mass concrete, complete all as specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed, including watering, complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate, 40 mm thick, with polythene film 50 micron thick laid on a coat of bitumen primer at 0.50 kg per sqm as in DPC, complete all as specified and directed.

M&L for precast cement concrete solid blocks masonry made with 1:2:4, type B-1, blocks exceeding 10 cm in width and set in CM 1:4, complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to required shape including cranking, bending, spiralling for hooping for columns, hooking ends and binding with and including mild steel annealed wire not less than 0.9 mm dia, complete all as specified and directed.

M&L for mild steel TMT bars 5 mm to 8 mm dia, cut to length, bent to required shape including cranking, bending, spiralling for hooping for columns, hooking ends and binding with and including mild steel annealed wire not less than 0.9 mm dia, complete all as specified and directed.

M&L for RCC design mix M-30 using 20 mm graded stone aggregate as in foundations, footings, plinth beams, etc., complete all as specified and directed.

M&L for RCC design mix M-30 using 20 mm graded stone aggregate as in columns, pillars, piers, etc., complete all as specified and directed.

M&L for RCC design mix M-30 using 20 mm graded stone aggregate as in beams, cantilevers, bressummers and lintels over 1.5 m clear span including necessary formwork, complete all as specified and directed.

M&L for RCC design mix M-30 using 20 mm graded stone aggregate as in chajjas, including necessary formwork, complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, plinth beams, etc., for rough finished surfaces, complete all as specified and directed.

Use and waste of formwork to sides of pillars, columns, etc., for rough finished square or rectangular surfaces, complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, lintels, etc., complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in hard/dense soil, complete all as specified and directed.

Removing excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point as in soil, complete all as specified and directed.

M&L for steel plates (plain or chequered) and channels, square cut or notched (ordinary and countersunk) including forming holes without any attachment, Fe-410-W (Grade E-250) quality A, complete all as specified and directed.

S&F joist, channel, angle or tee sections as vertical posts fixed independently with or without connecting plates and column bracings, conforming to Fe-410-W or E-250 quality A, complete all as specified and directed.

S&F rolled steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters, and running rails and guides fixed with angle cleats or other connecting plates, conforming to Fe-410-W or E-250 quality A, complete all as specified and directed.

S&F wind ties for roofs including securing bolts and similar work, conforming to Fe-290 Grade E-165, complete all as specified and directed.

M&L for preparation of new steel surfaces of any description exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc-chrome primer, complete all as specified and directed.

M&L for pre-painted galvalume aluminium-zinc coated GI based corrugated steel sheet 0.5 mm thick of any colour, having minimum tensile strength of 550 MPa, as in roof covering or wall cladding, fixed with self-tapping screws, complete all as specified and directed.

M&L for pre-painted galvalume aluminium-zinc coated GI based plain steel sheet 0.5 mm thick of any colour, having minimum tensile strength of 550 MPa, as in ridges or roof covering/wall cladding, fixed with self-tapping screws, complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 on fair faces of concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:4 on fair faces of brickwork or concrete surfaces as backing coat for wall tiles, etc., complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:4 on fair faces of concrete ceiling surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm wood-grain printed PVC sheet reinforced with MS square tube, edges painted to match the printed sheet, complete all as specified and directed.

S&F factory-made solid panel PVC door shutter 30 mm thick (styled), consisting of MS tube frame for top and bottom rails, MS frame covered with heat-moulded wood-grain printed PVC “C” channel having 5 mm thick PVC sheet beading 15 mm wide inside stiles and rails, wood-grain printed colour PVC sheet for top rail, lock rail and bottom rail on both sides with gap insert for top and bottom rails, panelling of wood-grain printed colour PVC sheet fitted in MS frame and welded/sealed to stiles and rails with decorative PVC beading 10 mm x 10 mm (90°), jointed with solvent cement, supplied and fixed in the frame at site, complete all as specified and directed.

M&L for powder-coated aluminium frames and shutters for doors, sliding windows and ventilators (movable louvre type) and for partitions with one or more rebates including joining cleats, rubber gasketing all round panels/shutters to fix glass, PVC gasketing in all channels, locking arrangement, with powder coating minimum 50 micron thick, complete all as specified and directed.

S&F powder-coated aluminium (minimum 50 micron) door shutters, fixed type without sash bar, aluminium section weighing not less than 0.55 kg/m including joining cleats, glazing clips, rubber packing, two handles per door, hinges, anodised aluminium snap beading and screws, complete all as specified and directed.

S&F powder-coated aluminium (minimum 50 micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing not less than 0.55 kg/m including joining cleats, glazing clips, rubber packing, anodised aluminium snap beading and screws, complete all as specified and directed.

S&F 4.0 mm thick sheet glass, ordinary quality, fixed with oil putty in panes not exceeding 0.5 sqm each to aluminium windows/ventilators, complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average aperture 1.40 mm, fixed with stainless steel wire staples, complete all as specified and directed.

M&L for 18 mm thick PVC ply board/sheets, both sides plain, as in door shutters, partitions, drawers and shelves, including solvent cement and beadings, fixed as per manufacturer’s instructions, complete all as specified and directed.

S&F 100 mm butt hinges, mild steel, with mild steel hinge pin, bright polished and fixed, type B-11, complete all as specified and directed.

S&F 150 mm long anodised aluminium barrel tower bolts of extruded sections, complete all as specified and directed.

S&F 300 mm long aluminium alloy anodised sliding door bolts with hasp and staple and fixing clips of extruded sections, including bolts and sliding bolts of extruded or cast aluminium alloy, complete all as specified and directed.

S&F 150 mm extruded aluminium alloy handles, cast type, fixed complete all as specified and directed.

S&F aluminium (die-cast) body door closer, hydraulically regulated, designation No. 3, universal type, suitable for door shutters 851 to 1000 mm wide and weighing between 61 and 80 kg, complete all as specified and directed.

S&F double-action floor spring, hydraulically regulated, made of minimum 1.25 mm thick aluminium alloy sheet foundation box with stainless steel cover, governing pivot of brass and other parts of mild steel, heavy duty, complete all as specified and directed.

S&F seat cover for pedestal pan, plastic, white, closed pattern with flat bottom and cover and mild steel chromium-plated or aluminised hinging device, complete all as specified and directed.

S&F 10 litre capacity PVC valveless syphonic flushing cistern, high or low level (exclusive of brackets), white, with inlet ball valve, float and handle including brackets, complete all as specified and directed.

S&F 15 mm dia PVC connection 450 mm long, complete all as specified and directed.

S&F PVC flush pipe 32 mm dia for low-level flushing cistern to pedestal pan, including all joints, cones and rubber nozzles to W.C. pan, complete all as specified and directed.

S&F health faucet with ABS body, chromium-plated, suitable for 15 mm dia pipe, with 1.25 m long flexible tube and ABS wall hook, including making connection and fixing in position, complete all as specified and directed.

S&F two-way bib cock, chromium-plated brass, with two levers and wall flange, screwed for 15 mm bore iron pipe, complete all as specified and directed.

S&F oval-shaped under-counter vitreous china wash hand basin, size 590 x 420 mm, including brackets, 32 mm waste brass chromium-plated (minimum weight 32 mm - 260 g) with long screwed shanks and fly nuts and PTMT bottle trap having minimum water seal of 25 mm , complete all as specified and directed.

S&F fancy type pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, lettered “Hot” or “Cold”, with long screwed shanks and fly nuts, screwed for 15 mm bore iron pipe, complete all as specified and directed.

S&F 32 mm waste fitting coupling, brass, chromium plated, for glazed ware sinks, basins, etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.

S&F 32 mm dia, 900mm long, PVC waste pipe for wash hand basins and urinals, complete all as specified and directed.

S&F brass chromium-plated towel rail, 20 mm dia, “D” type, 600 mm long between flanges, fixed in repairs, complete all as specified and directed.

S&F vitreous china urinal, bowl type (back or corner wall type), complete including plugs, bedding in CM 1:2, securing to wall with 60 mm long brass screws, pointing around back in cement, fixing automatic flushing cisterns with brackets, flush pipes, inlets and outlets, including 32 mm PVC waste pipe, etc., fixed in repairs, complete all as specified and directed.

S&F push type taps for urinals, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm dia iron pipe or brass ferrule, fixed in repairs, complete all as specified and directed.

M&L for coloured glazed ceramic tiles 300 x 450 x 6–7 mm thick on vertical surfaces such as skirting, dado and risers to steps, etc., set on and including 10 mm thick backing coat plaster in CM 1:3, set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles, complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7–8 mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors, laid over and including 15 mm thick screed bed in CM 1:4, set and jointed in neat grey cement slurry and pointed in white or coloured cement to match, complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying one coat of alkali-resisting primer and two coats of oil emulsion distemper, complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and applying one coat of self-primer and two coats of weather-proof exterior acrylic emulsion paint, complete all as specified and directed.

M&L for applying 3 mm thick wall care putty on wall surfaces, complete all as specified and directed.

M&L for applying 3 mm thick wall care putty on ceiling surfaces, complete all as specified and directed.

M&L for 100mm thick plain cement concrete 1:3:6 type C-2 using 40 mm graded aggregate as in sub-base/ plinth protection, complete all as specified and directed.

M&L for bitumastic gola using 80/25 bitumen and coarse sand in proportion 1:3 by weight, 8 cm x 8 cm, as joint strip in plinth protection, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in surface channels and drains, complete all as specified and directed.

M&L for precast cement concrete solid blocks masonry made with 1:2:4, type B-1, blocks exceeding 10 cm in width and set in CM 1:6, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded aggregate as in coping, complete all as specified and directed.

M&L for rendering 15 mm thick on internal surfaces of drain in CM 1:4, finished even and smooth without using extra cement, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm, complete all as specified and directed.

Removing excavated material to a distance exceeding 200 m but not exceeding 500 m and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and directed.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates, etc., including welding, grinding, buffing, polishing and forming curves where required and fixing with stainless steel nuts and bolts, including necessary accessories and stainless steel dash fasteners/bolts for fixing on top of floor or side of waist slab, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, etc., laid, bedded and pointed in any mortar, and removal of debris off the site, complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation) or insulation boards/slabs/blankets of any description and thickness including frame/grid of any description, complete all as specified and directed.

M&L for anodised aluminium snap grid (minimum 15 micron anodisation) of size 605 x 605 mm with anodised aluminium angle 40 x 25 x 2 mm thick weighing 0.36 kg per rm and anodised aluminium main and cross tees 36.5 x 23.5 x 1.5 mm thick weighing 0.254 kg per rm and 23.5 x 23.5 x 1.5 mm thick weighing 0.202 kg per rm respectively, for false ceiling, complete all as specified and directed.

M&L for 10 mm thick PVC insulation panels with EPS bonded to 1 mm plain PVC sheet, suitably placed in false ceiling grid made of aluminium/GI/MS as specified, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking shutters off the frame) exceeding 1.5 sqm but not exceeding 4 sqm each, including making good disturbed portions to match adjoining surfaces and accounting for credit as per schedule of credit, complete all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average aperture 1.40 mm, fixed with aluminium wire staples, complete all as specified and directed.

S&F anodised aluminium grill (transparent or dyed as per IS 1868 with minimum anodic coating grade AC-15) of approved design/pattern, with standard sections, fixed to existing window frame with C.P. brass/stainless steel screws at 200 mm centres, including cutting to opening size and providing anodised aluminium section around the opening, complete all as specified and directed.

Supply and fix WPC board 650 density, plain or pre-laminated one side, for cabinets and shelves including all hardware and solvent, complete all as specified and directed. Make: Rajshri Plasticwood or equivalent.

Dismantling floor, hearth or wall tiling including cement-mortar bedding (but not backing), removing serviceable tiles to store and removing rubbish as directed, complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7–8 mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors, laid over and including 15 mm thick screed bed in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles, complete all as specified and directed.

M&L for cement concrete tiles 250 x 250 x 22 mm thick, machine pressed, using grey cement with pigments, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick bedding layer in CM 1:6, complete all as specified and directed.

Supply and fix in repairs seat cover for pedestal pan, plastic, white, closed pattern with flat bottom and cover and mild steel chromium-plated or aluminised hinging device, complete all as specified and directed.

Supply and fix in repairs 10 litre PVC valveless syphonic flushing cistern, high or low level (exclusive of brackets), white, with inlet ball valve, float and handle including brackets, complete all as specified and directed.

Supply and fix in repairs PVC flush pipe 32 mm dia for low-level flushing cistern to pedestal pan, including all joints, cones and rubber nozzles to W.C. pan, complete all as specified and directed.

Supply and fix in repairs health faucet (ABS body), chromium plated, suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook, including making connections and fixing in position, complete all as specified and directed.

Supply and fix in repairs flat-back vitreous china wash hand basin, size 550 x 400 mm, including brackets, 32 mm waste brass chromium plated with long screwed shanks and fly nuts and bottle trap, complete all as specified and directed.

Supply and fix in repairs fancy type pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with lettered “Hot” or “Cold”, long screwed shanks and fly nuts, screwed for 15 mm bore iron pipe, complete all as specified and directed.

Supply and fix in repairs 32 mm waste fitting (coupling), brass, chromium plated for glazed ware sinks, basins, etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.

Supply and fix in repairs bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe, complete all as specified and directed.

Supply and fix in repairs stop valves/angle valves, cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle, screwed both ends for 15 mm bore iron pipe, complete all as specified and directed.

Supply and fix in repairs aluminium body door closer, hydraulically regulated, designation No. 3, universal type, suitable for door shutters 851 to 1000 mm wide and weighing between 61 and 80 kg, complete all as specified and directed.

M&L for point wiring with 1.5 sqmm (nominal area) single-core, multistranded copper conductor, PVC insulated but unsheathed FRLS cable 1100 V, drawn through and including concealed 20 mm dia PVC conduit with accessories (tees, bends, elbows, sockets, etc.), chiselling and making good disturbed surfaces with CM 1:4 and matching paint; including 1.5 sqmm FRLS green PVC insulated copper earth wire, modular box with cover plate of suitable size for housing switches, sockets, regulators, etc., complete for the following:-

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One 5-pin, 6 A socket outlet on independent board.

(d) One 5-pin, 6 A socket outlet on the same board.

Supply and fix 5 A one-way piano type flush switch, ISI marked, matching existing make, complete all as specified and directed.

S&F 5 A, 5-pin 2-in-1 flush type socket outlet, complete all as specified and directed.

Supply and fix ceiling rose, PVC/polycarbonate insulated body, suitable for 3-core connection, complete all as specified and directed.

S&F 100 W high-bay LED luminaire, robust and energy-saving, with pressure die-cast aluminium housing and toughened glass, system wattage 100 W, 140–260 V AC, system lumen output 10,000–12,000 lm, CCT 5700–6500 K, PF > 0.95, CRI ≥ 70, THD ≤ 10%, minimum in-built surge protection 2.5 kV, complete all as specified and directed.

S&F surface/wall-mounted LED batten with aluminium housing and integral electronic driver, 10 W, 140–260 V AC, system lumen output 1000–1200 lm, CCT 5700–6500 K, PF > 0.95, CRI ≥ 70, THD ≤ 10%, with minimum in-built surge protection 2.5 kV, decorative type, complete all as specified and directed. Make: Cat. Part No. LUMILINE PLUSEPRO BS 10W LED865SPCSSIND or equivalent.

S&F surface/wall-mounted Regal batten including suitable 20 W LED tube (4 ft), complete all as specified and directed. Make: Cat. Part No.: REGALBATTEN8UPTO1X22WDSBSWH and PHOTONULTRAE2.01213T8SSTL20WLED865SPC or equivalent.

Supply and fix exhaust fan, steel body, AC single-phase 230 V, 300 mm sweep, 2100 RPM, air delivery 600 CMH, power rating 52 W, noise level 45 dB, with frame and back louvers, complete all as specified and directed. Note: Old unserviceable fan shall be deposited in MES store. Make: Cat No: SKU 70001 of Bajaj/CG/Orient or equivalent.

Supply and fix 70 W LED street-light fitting, 230 V AC, outdoor type with high-pressure die-cast aluminium housing, impact and corrosion resistant, IP-65/66 protection, with driver and mounting bracket, complete all as specified and directed.

Supply, laying and testing XLPE insulated, screened, PVC bedded, galvanised steel strip/wire armoured heavy duty aluminium conductor power cable 1100 V grade of size 2-core 10 sqmm, complete all as specified and directed.

Supply and fix sheet-metal enclosure MCB distribution board (DB) SPN 4-way, double-door type with bus-bar, complete all as specified and directed.

Supply and fix 240 V, 10 kA ‘C’ curve MCB SPN 32 A, including connections, testing and commissioning, complete all as specified and directed.

M&L for sub-main wiring with two runs of 2.5 sqmm multistranded copper conductor PVC insulated FRLS cable 1100 V, drawn through 25 mm dia PVC conduit with accessories, concealed on wall/ceiling, and one run of 2.5 sqmm FRLS green PVC insulated copper earth continuity conductor, complete all as specified and directed. Note: (i) Phase shall be of Red/ Yellow/ Blue, neutral shall be of black and earthing wire shall be of green colour as per standards (ii) Two runs of cable for phase/ neutral and one run of cable for earth shall be measured and paid as one unit length.

Supply and fix 240 V, 10 kA ‘C’ curve MCB SP 6–32 A, including connections, testing and commissioning, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings, etc., removing materials to store for safe custody or credit, and making good disturbed surfaces of walls/floors, complete all as specified and directed.

M&L in replacement for point wiring with two runs of 4 sqmm multistranded copper conductor PVC insulated FRLS cable 1100 V and one run of 4 sqmm green PVC insulated multistranded copper earth continuity conductor, drawn in rigid PVC conduit with accessories, concealed in wall/ceiling/trusses with clamps/screws, including GI sunken boxes with earth dolly, modular white cover plate and frame for 15 A multi-purpose socket outlet on independent board, including testing, complete all as specified and directed.

Supply and fix in repairs LED tube light 10 W, CCT 6500 K, CRI < 80, PF 0.9, THD > 20%, 4 kV surge protection, box-type 2 ft fitting including necessary connections, complete all as specified and directed. Make: Cat: BCLSB 10W WH of Bajaj/CG/Orient or equivalent.

Supply and fix in repairs LED tube light 20 W, CCT 6500 K, CRI < 80, PF 0.9, THD > 20%, 4 kV surge protection, 4 ft fitting including 3-core flexible copper cable from ceiling rose to connector, complete all as specified and directed. Make: Cat: BCLSB 20W WH of Bajaj/CG/Orient or equivalent.)

S&F in repairs 36 W LED panel light, CCT 5700 K, CRI < 80, PF 0.9, THD > 20%, 4 kV surge protection, square surface-mounted 2' x 2' luminaire with polymer diffuser and all accessories, complete all as specified and directed. Make: Cat: BZRSQL 36W LED G54 WH of Bajaj/CG/Orient or equivalent.

Supply and fix in repairs exhaust fan, steel body, AC single-phase 230 V, 300 mm sweep, 2100 RPM, air delivery 600 CMH, power rating 52 W, noise level 45 dB, with frame and back louvers, complete all as specified and directed. Note: Old unserviceable fan shall be deposited in MES store. Make: Cat: SKU 70001 of Bajaj/CG/Orient or equivalent.

Supply and fix ceiling fan complete with blades, down rod, electronic regulator and accessories, 230 V, 1200 mm sweep, white/brown finish, copper motor, air delivery 220 CMM, speed 350 RPM, power rating 28 W, five-star rated BLDC motor, connected with 23/0.0076 stranded copper flexible cord not less than 0.7 m long, complete all as specified and directed. Note: Old unserviceable ceiling fan shall be deposited in MES store.

Supply and fix in repairs wall-mounted fan, AC single-phase 230 V, 400 mm sweep, white colour, air delivery 90 CMM, 2150 RPM, with left/right gearbox mechanism and 3-speed control (low/medium/high) and 100% copper motor 115 W, connected with flexible copper cord not less than 0.7 m long, complete all as specified and directed. Note: Old unserviceable wall-mounted fan shall be deposited in MES store. Make: Cat: SKU 250892 of Bajaj/CG/Orient or equivalent.

Supply and fix in repairs five-step electronic fan regulator, flush type, on existing plate, 230 V single phase, complete all as specified and directed.

Supply and fixing in repairs lamp holder 250 V, 10 A, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

Supply and fix in repairs modular 6 A two-way piano flush switch, ISI marked, matching existing make, complete all as specified and directed.

S&F modular piano flush switch, 6 A, single-pole, one-way, complete all as specified and directed.

S&F modular piano flush switch, 15 A, single-pole, one-way, complete all as specified and directed.

S&F modular socket outlet, multipurpose, 3-pin 6 A and 2-pin 6 A, piano flush type, complete all as specified and directed.

S&F modular socket outlet multipurpose, piano flush type, having provision for 3-pin 15 A and 3-pin 5 A, complete all as specified and directed.

Supply and fix in repairs ceiling rose, PVC/polycarbonate insulated body, suitable for 3-core connection, complete all as specified and directed.

Supply and fix in repairs 12 W LED bulb, complete all as specified and directed.

Supply and fixing in repairs sheet-metal enclosure MCB DB SPN 8-way, double-door type with bus-bar, complete all as specified and directed.

Supply and fixing in repairs 240 V, 10 kA ‘C’ curve MCB SP 6–32 A including connections, testing and commissioning, complete all as specified and directed.

Supply and fixing in repairs 240 V, 10 kA ‘C’ curve MCB SPN 32 A including connections, testing and commissioning, complete all as specified and directed.

Supply and fixing in repairs sheet-metal enclosure MCB TPN DB 4-way, double-door type with bus-bar, complete all as specified and directed.

Supply and fixing 415 V, 10 kA ‘C’ curve MCB TPN 40–100 A in DB including connections, testing and commissioning, complete all as specified and directed.

Supply and fixing in repairs 240 V, 10 kA ‘C’ curve MCB SPN 40–63 A including connections, testing and commissioning, complete all as specified and directed.

M&L in repairs for sub-main wiring with two runs of 6 sqmm multistranded copper conductor PVC insulated FRLS cable 1100 V drawn through 25 mm dia PVC conduit with accessories, concealed on wall/ceiling, and one run of 6 sqmm PVC insulated multistranded copper earth continuity conductor connected to common earth dolly, complete all as specified and directed. Note: (i) Phase shall be of Red/ Yellow/ Blue, neutral shall be of black and earthing wire shall be of green colour as per standards (ii) Two runs of cable for phase/ neutral and one run of cable for earth shall be measured and paid as one unit length.

LEKSHMI ENGINEERS (BID ID -3500250)

K.G.SHANKER (BID ID -3504344)

Ramshree Global Constructions Pvt. Ltd (BID ID -3500470)

ABDUL RAHIM (BID ID -3500735)