CA NO. CWE SGNR - 83 OF 2020-21 SPECIAL REPAIRS TO BUILDING NO. P-182/1 TO 4 AND P-54/1 TO 4 IN BHAGAT ENCLAVE AREA AT MILITARY STATION SRI GANGANAGAR

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding and rubbish off the premises complete all as specified and directed by Engineer - in - Charge.

M&L glazed ceramic coloured tiles interior grade, (300x600)x7mm thick as on vertical surfaces like dados or skirting over 10mm thick rendering in CM 1:4, set & jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for non-skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., 15 mm thick screed bed or bedding layer of cement mortar 1:4,set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L 20 mm thick black Granite table rubbed and polished in steps,jambs,pillars,window cills,cooking platforms and like in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite complete all as specified and directed by Engineer - in - Charge.

M&L for Vetrified Ceramic tiles 10 mm thick (square/rectangular) polished area of each tiles not exc 0.36 sqm , over 15 mm thick screed bed CM 1:4,in floors etc set and jointed in neat cement slurry and pointed in white cement slurry and pointed in white cement or coloured cement to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 05 here in before but on vertical surfaces over 10mm rendering in CM 1:3 finished even and fair complete all as specified and directed by Engineer - in - Charge.

Demolition concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed by Engineer - in - Charge.

M&L 25 mm thick cement concrete flooring type B-0, 1:2:4 (12.5 mm graded stone aggregate) finish even and fair complete all as specified and directed by Engineer - in - Charge.

M&L PCC 1:4:8 type D2 using 40mm graded aggregate as in sub base, floors founradtions filling & mass concrete complete all as specified and directed by Engineer - in - Charge.

M&L machine cut Kota stone slab flooring 20-25 mm thick over cement screed base 20 mm thick in cement mortar 1:4 laid and jointed withgrey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including Mirror Polishing finishing complete all as specified and directed by Engineer - in - Charge.

All as srl item No 10 here-in-before but for as in skirting ,dados laid over 10 mm thick rendering in CM 1:3 complete all as specified and directed by Engineer - in - Charge.

Dismantling brick tiles, single layer on roof complete all as specified and directed by Engineer - in - Charge.

Demolition of old mud phuska, removing rubbish of the premises cleaning surface and preparing to receive new mud plaster complete all as specified and directed by Engineer - in - Charge.

M&L for PCC 1:2:4 type B2(20 mm graded aggregate) as in roof padding/mass concrete complete all as specified and directed by Engineer - in - Charge.

Providing and applying waterproofing work with polyester reinforced APP membrane sheet of thickness 3mm by mechanically clean the RCC slab and wall with wire brush / coir brush to free from loose materials like dust, dirt etc. Make : wattah / coving of 50mm x 50mm at all horizontal and vertical joints to avoid right angle turning with polymer based mortar. Apply heat resistant aluminium painting over waterproofing membrane. Apply one coat of solvent based bitumen primer on cleaned and leveled surface @ 3 - 5 Sqmm / Ltr per coat. Unroll the torchshield roll after application of primer. Align the torchield roll correctly and reroll it in alignment before torching. Use gas burner to heat substrate and underside to softening points. When the embossing disappears, roll forward and press firmly against substrate to bond from the lower and towards the higher end. Keep overlap margin from minimum 100mm. Heart both the overlaps and use round tripped trowl to seal overlap. Excess compound should be smoothended and pressed into seam using hot trowl complete all as specified and directed by Engineer-in-Charge. Make : Dr. Fixit / STP

Taking down chowkhats or frames (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down and refixing shutters exceeding 1.0 Sqm and not exceeding 2.0 Sqm each in same opening after resecuring or easing and adjusting complete all as specified and directed by Engineer - in - Charge.

Taking down chowkhats or frames (without taking off shutters from the frames) not exceeding 1.5sqm each complete all as specified and directed by Engineer - in - Charge.

S & F Glass Reinforced plastic (FRP) Door Frames of three legged of cross section 90mmx45mm having single rebate of 32mmx45mm having single rebate of 32mmx15mm to receive shutter of 30 mm thickness. The laminate door frame molded with fire retardant grade unsaturate polysterresinn and chopped mat.Doorframe laminate shall be 2 mm thick and shall be filled with suitable wooden black in all the three legs. The frame shall be covered with fiberglass from all sides MS stay shall be provided at the bottom to steady the frame complete all as specified and directed by Engineer - in - Charge.

S & F 30mm thick glass fiber reinforced plastic (FRP) paneled door shutter of required color and approved brand and manufacture made with fire retardent grade unsaturated polyster resin moulded to 3mm thick FRP laminated for forming hollow rails and style with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings cast monolithically with 5mm thick FRP laminate for panels for conforming to IS:14856-2000 complete all as specified and directed by Engineer - in - Charge.

S&F 150mm Extruded aluminium alloy handles fabricated D type complete all as specified and directed by Engineer - in - Charge.

S&F 150 mm Aluminium anodised barrel tower bolts complete all as specified and directed by Engineer - in - Charge.

S&F 100 mm Butt hinges stainless steel complete all as specified and directed by Engineer - in - Charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., size of frame 105x60mm complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 25 here in before but size 125 x 60mm complete all as specified and directed by Engineer - in - Charge.

S&F plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints in 2nd class hard wood complete all as specified and directed by Engineer - in - Charge.

S&F 18/19 mm prelaminated particle board ,interior grade ,preliminated both sides with decorative choice laminations fixed with screws complete all as specified and directed by Engineer - in - Charge.

S & F 100mm size hasp and staple, safety type of aluminiun anodised complete all as specified and directed by Engineer - in - Charge.

S&F continous piano hinges mild steel bright finish or galvanised of 30 mm width of flaps complete all as specified and directed by Engineer - in - Charge.

S&F 35 mm thick factory made gauged skelton shutters open rebeted and prepared to receive gauze etc edges of framing plain , chamferedv or rounded fitted with cut and mitred beady for receving gauze etc of 35 mm thick and door for IInd class hard wood rail and style complete all as specified and directed by Engineer - in - Charge.

S&F 35 mm thick Factory made IInd class hard wood plain framed panelled shutters (Two Panels ) with lock rails and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces . the size of rail and stile as per IS :1003 (Part -i) Klin Seasoned and chemically pressure treated complete all as specified and directed by Engineer - in - Charge.

S&F 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engineer - in - Charge.

S&F door viewer vide angle brass with glass cap 14 mm dia complete all as specified and directed by Engineer - in - Charge.

M&L mortice lock with two lever (vertical type) with brass body 100 mm long complete all as specified and directed by Engineer - in - Charge.

M&L two coat of synthetic enamel on wooden surfaces (ordinary tint) over new surface over 10cm width or girth including preparation of surface complete all as specified and directed by Engineer - in - Charge.

M&L one coat of synthetic enamel on wooden surfaces (ordinary tint) old painted surface over 10cm width or girth including preparation of surface complete all as specified and directed by Engineer - in - Charge.

Supply only mild steel butt hinges “medium weight” 100mm long cold rolled mild steel complete all as specified and directed by Engineer - in - Charge.

Supply only mild steel butt hinges “medium weight” 50mm long cold rolled mild steel complete all as specified and directed by Engineer - in - Charge.

Taking down steel window or ventilator fixed type with glazing bar complete all as specified and directed by Engineer - in - Charge.

S&F Aluminium frame for doors, window, ventilators with one or more rebates including joining cleat for fixing etc complete with powder coating on Aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fasteners . Aluminium section shell be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and directed by Engineer - in - Charge.

S&F Anodised aluminium window and ventilator shutters aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles two Nos. in each door, hinges, anodized aluminium snap beading, screws with powder coating of any colour (thickness of powder coating not less than 50 micron) complete all as specified and directed by Engineer - in - Charge. Note:- Sheet glass will paid separately under respective item(s) of BOQ

S&F Annodised Aluminum frame or Grill powder coated any pattern fixed with Aluminum Frame complete all as specified and directed by Engineer - in - Charge. Note- Aluminum frame shall be Measured and paid seperately under respective item(s) of BOQ

S&F 5.5 mm thick sheet glass ordinary quality in square not exceeding 0.5 sqm in each pane complete all as specified and directed by Engineer - in - Charge.

S & F framed work such as grills, grating, etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 290-Gde-165 complete all as specified and directed by Engineer - in - Charge.

M&L Cement concrete 1:3:6 type C–1(12.5 mm graded stone aggregate) filling of pressed steel frame and hold fast blocks etc complete all as specified and directed by Engineer - in - Charge.

M & L applying one coat of red oxide primer on new steel surface of any description over 10cm in width or girth, not otherwise described complete all as specified and directed by Engineer - in - Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames, including punching or drilling out old glazing pins / spring clips and glazed with oil putty complete all as specified and directed by Engineer - in - Charge.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed by Engineer - in - Charge.

M&L two coats of synthetic enamel paint (ordinary tint) on steel surface over 10 cm width or girth, not otherwise described including preparation of new steel surface complete all as specified and directed by Engineer - in - Charge.

M&L one coat of synthetic enamel paint (ordinary tint) on steel surface over 10 cm width or girth, not otherwise described including preparation of old steel surface complete all as specified and directed by Engineer - in - Charge.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed by Engineer - in - Charge.

S & F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm to steel frame of window with tinned tacks or galvanised wire stapels complete all as specified and directed by Engineer - in - Charge.

S&F 300 mm mild steel sliding door bolts, clip type, stone enameled block with bright bolt not less than 12mm dia with and incl a minimum of 6 bolts and nuts, 4 on bolt plate 2 on staple plate complete all as specified and directed by Engineer - in - Charge.

S & F aluminium alloy, anodized, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast – aluminium alloy and fixed complete all as specified and directed by Engineer - in - Charge.

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer - in - Charge.

M&L 15mm thick rendering in CM 1:6 to brick / concrete wall surfaces finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L 15mm thick rendering in CM 1:4 to brick / concrete wall surfaces finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L 5 mm thick rendering in CM 1:3 on fair faces of concrete surfaces as on ceilings finished even and smooth complete all as specified and directed by Engineer - in - Charge.

M&L three coats of white wash to undecorated ceiling surfaces including preparation of new surfaces complete all as specified and directed by Engineer - in - Charge.

M & L one coat of white wash to old decorated plastered surfaces of ceilling including preparation of surfaces complete all as specified and directed by Engineer - in - Charge.

M & L two coats of oil bound distemper on old plastered surfaces of wall including complete removal of existing treatment complete all as specified and directed by Engineer - in - Charge.

M & L two coats of oil bound distempering over chalk whitening on new plastered surfaces preparatory to distempering of wall including 3 mm thick wall care putty & preparation of surface complete all as specified and directed by Engineer - in - Charge.

M & L applying two coats of acrilic smooth exterior emulsion paint with silicon additives on external surface of wall includind two coats of wal primer as per manufacturers instructions after complete removal of existing treatment complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 64 here-in-before but for over new plastered surface of wall complete all as specified and directed by Engineer - in - Charge.

M&L one coat of white wash on old decorated plastered or un-plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in - Charge.

M&L applying two coat of white wash on new plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in - Charge.

Taking up or down for 20mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

S&F steel water tubing galvanised 20mm bore, “medium grade” with all fittings fixed to wall and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 69 here in before but for fixing with new fittings only complete all as specified and directed by Engineer - in - Charge.

Taking up or down for 15 mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

S&F steel water tubing galvanised 15mm bore, “medium grade” with all fittings and fixed to walls and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 72 here in before but for fixing with new fittings only complete all as specified and directed by Engineer - in - Charge.

S & F in repairs bib taps with wall flange 15mm dia, cast copper alloy fancy type chromium plated, with crutch or butterfly handle, screwed down screwed for iron pipe complete all as specified and directed by Engineer - in - Charge.

S&F in repairs, bib taps, cast copper alloy, with crutch or butterfly handles, screwed down, screwed for iron pipe or brass ferrule for 15mm bore complete all as specified and directed by Engineer - in - Charge.

S&F in repairs, stop valves, cast screwed down, high pressure copper alloy, with crutch or butterfly handles, screwed both ends for 15mm bore iron pipe or brass ferrule complete all as specified and directed by Engineer - in - Charge.

S&F in repairs, stop valves, cast screwed down, high pressure fancy type chromium plated, with crutch or butterfly handles, screwed both ends for 20mm bore iron pipe or brass ferrule complete all as specified and directed by Engineer - in - Charge.

S&F in repair 15 mm dia fancy type chromium plated concealed type stop valves, cast copper aloy with crutch or butterfly handles screwed down high pressure, screwed both ends for iron and fixed complete all as specified and directed by Engineer - in - Charge.

Dismantling water tank capacity N. exceeding 250 complete all as specified and directed by Engineer - in - Charge.

S&F rotational moulded polyethylene water storage tank 500 ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engineer - in - Charge.

S&F 20mm bore ball brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed by Engineer - in - Charge.

S&F in repairs, Brass CP mixer for mixing hot and cold water screwed down for iron pipe and fied complete all as specified and directed by Engineer - in - Charge.

S&F in repair health faucet (hand shower for EWC) having 1.2 m length with hanging device Chromimum plated complete all as specified and directed by Engineer - in - Charge.

Dismantling cast iron work of any description and any position complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

Extra over 100 cast iron pipes and fittings if lead joint is provided in lieu of cement joint complete all as specified and directed by Engineer - in - Charge.

Extra over 75 mm cast iron pipes and fittings if lead joint is provided in lieu of cement joint complete all as specified and directed by Engineer - in - Charge.

M&L for CI floor trap 75 mm with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer - in - Charge.

M&L for CI floor trap 100 mm with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer - in - Charge.

S&F in repair Grating doom 100mm dia stainless steel (minimum weight 25gms) complete all as specified and directed by Engineer - in - Charge.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan – necks, etc. including cleaning of any description complete all as specified and directed by Engineer - in - Charge.

M&L bands straps supports or stays for rainwater ventilating pipes including bolts confirming to Fe 410 -0 or Fe 310-0 complete all as specified and directed by Engineer - in - Charge.

Cutting holes into brick wall for inserting hold fast etc built in C:M n exc half brick wall and making good in cement conc 1:2:4 complete all as specified and directed by Engineer - in - Charge.

S&F 110mm bore PVC (SWR) rain water pipe single socketed in any length with rubber ring joints, jointed with solvent joint fixed to wall complete all as specified and directed by Engineer - in - Charge.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed by Engineer - in - Charge.

Dismantling of brick work built in cement mortar of any description complete all as specified and directed by Engineer - in - Charge.

M&L brick work with fly ash old size ' Bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 100 here in before but for except bricks complete all as specified and directed by Engineer - in - Charge.

M & L brick work with fly ash old size ' Bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed by Engineer - in - Charge.

S & F in repair brass chromium plated tubular towel rail 20mm dia “D” type 60 cm long between flanges including brackets complete all as specified and directed by Engineer - in - Charge.

S&F in repair stainless steel plate rack of size 36"x 36"x10" made out of 0.6 mm thick stainless steel sheet of first quality complete all as specified and directed by Engineer - in - Charge.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer - in - Charge.

S&F water closet vitreous china squatting pan "Orrisa pattern" size 580mmx440mm white with integral foot rests (Excl flushing cistern) complete all as specified including CI 'P' trap complete all as specified and directed by Engineer - in - Charge.

S&F in repair vitreous china wash down water closet pan (Pedstal pattern), white excluding fixing bolts, flushing cistern and flush pipe, including plastic water coset seat, black cosed pattern with flat bottom, and cover and mild steel chromimum plated hinging device complete all as specified and directed by Engineer - in - Charge.

S&F in repairs, PVC low level flushing cistern 10 lirs capacity, valve-less, syphonic action type, white, with inlet, ball valve, float, and handle including brackets, PVC connections 15 mm size with PTMT nuts of length 450 mm ,including 32mm bore flush pipe of polyethylene of low or high density of PVC complete all as specified and directed by Engineer - in - Charge.

S&F in repair stainless steel curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm centre to centre) etc complete all as specified and directed by Engineer - in - Charge.

S&F, in repair vitreous china wash hand basin counter shank with black granite slab to be cut and polished at site as per requirement and approved by Engineer-in-charge, including brackets, 32mm bore brass chromimum plated waste coupling & 32mm bore low density ployethylene (LDPE) flush pipe of pressure rating 6Kgf/Sq cm (1.00 M long) complete, including 15mm cast copper alloy chromium plated fancy type Mixer pillar taps and 15mm bore 300mm length PVC connection with PTMT nuts complete all as specified and directed by Engineer - in - Charge. Note:- Granite shall be measured and paid seperately under respective item(s) of BOQ

S&F cabinet of PTMT with looking mirror of size 450x600mm complete all as specified and directed by Engineer - in - Charge.

M & L for 50 mm thick cement concrete type C – 1 (1:3:6) using 20mm graded stone aggregate as in plinth protection finished even and smooth etc complete all as specified and directed by Engineer - in - Charge.

Demolition of RCC slabs, chajjas and similar items complete all as specified and directed by Engineer - in - Charge.

M & L RCC 1:1½:3, Type A–1 for slabs supported on walls, beams, columns and in shelves, the like complete all as specified and directed by Engineer - in - Charge.

Form work to soffits of suspended slabs such as roof slab and similar work not exceeding 200mm thick with rough finished surface of concrete complete all as specified and directed by Engineer - in - Charge.

M & L mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 117 here in before but in stirrups, spacers and binder etc complete all as specified and directed by Engineer - in - Charge.

S&F IInd class hard wood small fittings such as brackets of any type shaped door and window stops and the like including all necessary labour article n.exc 200cucm each complete all as specified and directed by Engineer - in - Charge.

S&F, in repair vitreous china wash hand basin, white flat back of size 550mmx400mm including brackets, 32mm bore brass chromimum plated waste coupling & 32mm bore low density ployethylene (LDPE) flush pipe of pressure rating 6Kgf/Sq cm (1.00 M long) complete, including 15mm cast copper alloy chromium plated pillar taps and 15mm bore 300mm length PVC connection with PTMT nuts complete all as specified and directed by Engineer - in - Charge.

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes jali including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified and directed by Engineer - in - Charge.

Demolation of cement concrete in sunken portion and floor complete all as specified and directed by Engineer - in - Charge.

Providing and applying tow component cementitious and acrylic flexible waterproofing and protective coating ,two coats with 1mm DFT, having Hydrostatic (positive) water pressure resistance (DIN 1048) is 7. Abrasion resistance cm / km is 0.09 of Dr. Fixit PIDIFIN 2K / SMART CARE 2K or equivalent with a paint brush over existing roof surface. The polyesterreinforced coated net of 45 g / m2, 2.5mm x 2.5mm is laying on the surface immediately on the first coat of two component modified polymer Dr. Fixite pidifin 2K or equivalent. After removal of all loose materials like dust etc wtih wire brush coir brushes from roof surface to get absolutely cleaned surface free of foreign contaiminant filling of crack and patches with polymer based reapir mortar / micro concrete,after the repairing work making the gola on surrounding walls junction and seal the vertical walls upto 300mm in case of core cutting on the surface, the joint is seal with non-shrink grout complete all as specified and directed by Engineer - in - Charge. Note : Work shallbe executed through specialized agency, Waterpofing treatment is carried out in the complete sunken area and upto 300mm outer walls of the sunken area. This wall area should be including in the measurement book.

Supply only Water proofing compound complete all as specified and directed by Engineer - in - Charge.

M&L for cement concrete type E2 1:5:10 (40mm graded aggregate) as in filling and mass concrete etc complete all as specified and directed by Engineer - in - Charge.

S&F 100 mm size over head shower swivel type with arm complete all as specified and directed by Engineer - in - Charge.

S & F in repair bottle trap of PTMT 32mm dia having minimum water seal of 25mm (min weight 260gm) complete all as specified and directed by Engineer - in - Charge.

M&L 150 mm long (cover plate) Floor door stopper of aluminum alloy body and tongue anodised with hard drawn steel spring fixed in door complete all as specified and directed by Engineer - in - Charge.

40 mm dia brass polished cupboards knobs fixed with nut screw and washer of mild steel bright finished complete all as specified and directed by Engineer - in - Charge.

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer - in - Charge.

Double action spring hinges, mild steel with steel wire spring, stove enamelled, black complete all as specified and directed by Engineer - in - Charge.

S&F in preglazed chequred cement concrete tiles 25mm thick set jointed and pointed in neat cement slurry in floors laid over and including 15mm screed bed in CM (1:6) complete all as specified and directed by Engineer - in - Charge.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc complete all as specified and directed by Engineer - in - Charge.

Repair to damaged concrete slab by using micro mortar and concrete in following stages complete all as specified and directed by Engineer - in - Charge. (a) Removing the falling mortar and concrete from RCC slab and cutting the affected area in geometrical shape.(b) Cleaning the rusted reinforcement and applying rust removal.(c) Inserting addl reinforcement in case the cross sectional area reduction is more than 20 percent. Welding the reinforcement with existing one and supporting the new supporting adequately on walls if required with grout.(d) Providing micro mortar and concrete over bond coat to cover the reinforcement and slab surface.(e) Providing adequate formwork and scaffolding if required.(f) Curing the surfaceRust removal, Bonding agent, grout, micro mortar and concrete and related chemicals shall be of Dr Fixit/BASF and STP. Work is to be got executed from authorized applicators of company.

Taking down carefully steel rolling shutters including hood of size exceeding 25 Sqm for replacement of unserviceable & defective parts and refixing in the same opening after cleaning of guide rails, lath top cover by kerosene and proper greasing, oiling, replacement of rusted nuts bolts etc. removing of bent, disturbed surface, making alignment etc. to make good the system and size, bearing of adequate size/in hinges for rolling shutters and bevel gear complete all as specified and directed by Engineer - in - Charge.

S&F ball bearing for rolling shutters suitable for any size of rolling shutters complete all as specified and directed by Engineer - in - Charge.

S&F in repairs, Bib taps for sink cock with swing type Chrimium plated , screwed down, screwed for iron pipe or brass ferrule for 15mm bore complete all as specified and directed by Engineer - in - Charge.

M&L machine pressed precast concrete interlocking paver block(Glossy finish) any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed by Engineer - in - Charge.

M&L providing precast cement concrete 1:2:4 Type B1 with 20mm graded stone aggregate as in kerb stone with solid blocks exceeding 10 cm width and set in CM 1:4 etc. complete all as specified and directed by Engineer - in - Charge.

M&L for sand filling under floor or in foundation including watering and well consolidation complete all as specified and directed by Engineer - in - Charge.

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed by Engineer - in - Charge.

M&L one coat of Aluminium paint over priming with Aluminium red oxide on steel surface over 10 cm width or girth, not otherwise described including preparation of old steel surface complete all as specified and directed by Engineer - in - Charge.

Dismantling of posts or struts (wood,Steel or RCC) including taking out embedded portion demolition of PCC if any and making good disturbed ground complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.50 Mtr in depth for foundation, etc., not exceeding 10 Sqm on plan in soft /loose soil; & getting out complete all as specified and directed by Engineer-in-Charge.

Removing excavated material (Soil) not exceeding 50 mtrs & depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:3:6 (40mm graded stone aggregate) type C2, in foundation of posts and struts complete all as specified and directed by Engineer-in-Charge.

M&L mild steel work i.e. Angle iron/flat iron as in post and struts in fencing including cutting tops to shape, drilling holes, notching for wire etc conforming to Fe-290 grade E-165 complete all as specified and directed by Engineer-in-Charge.

S&F 10 mm dia MS round bar for fixing of chain link fencing with post complete all as specified and directed by Engineer-in-Charge.

M&L two coats of synthetic enamel over a coat of red oxide primer exc 10 cm width /girth on new dteel surfaces including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

Supply only chain link fencing galvanised mild steel hot dipped(IS -2721) of any size and type complete all as specified and directed by Engineer-in-Charge.

Fixing only of chain link fencing including above galvanised mild steel to any type of standard rails vision of binding wire complete all as specified and directed by Engineer-in-Charge.

S&F mild steel screw bolts (machine made) with hexagonal or square head at one end, screwed end to be fitted with washer and one hexagonal/ square nut not exceeding 5cm long complete all as specified and directed by Engineer-in-Charge.

Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed by Engineer-in-Charge.

M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 1.5 sqmm (Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for modular metal flush boxes suitable length and thickness for mounting, switches, sockets,fan regulator with modular cover plate with frame and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 1.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and directed by Engineer-in-Charge. Make : Anchor / Havells / Finolex or as approved by GE

All as per Srl item No. 154 here in before but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 154 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 154 here in before but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer-in-Charge.

All as Srl item No. 154 here in before but for one light point controlled by two 2 ways switches complete all as specified and directed by Engineer-in-Charge.

All as Srl item No. 154 here in before but for call bell point complete all as specified and directed by Engineer-in-Charge.

S & F modular switch 5/6 Amps single pole one way,one module complete all as specified and directed by Engineer-in-Charge.

S & F modular switch socket combination 5 pin, type 5/6 Amps5 in 1 flush type complete all as specified and directed by Engineer-in-Charge.

S & F modular switch socket combination 6 Pin, 5/16 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S & F modular switch 5/6 Amps single pole two ways complete all as specified and directed by Engineer-in-Charge.

S & F modular socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement industrial socket metal clad plug and socket with MCBs single pole 20 Amp complete all as specified and directed by Engineer-in-Charge.

S&F modular bell push 5 Amp complete all as specified and directed by Engineer-in-Charge.

S & F modular stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer-in-Charge.

S&F Electronic Bell AC 230 Volt single pole ding dong type complete all as specified and directed by Engineer-in-Charge.

S & F ceiling rose surface bakelite three terminals complete all as specified and directed by Engineer-in-Charge.

S & F in replacement of existing light fitting with LED batten with aliminium housing and integrated electronic driver, 20 watt having input voltage AC90-300V, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer-in-Charge. Make:Havells cat part No: LUMILINEPLUSBS20WLED865SPCSS , Bajaj cat part no.: BCLSBAL 20W CW ,Crompton cat part no. : CCS-100-20-65-HL2-DP-NWH or equivalent make as approved by GE

S&F in replacement security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer-in-Charge. Make:Havells cat part no: ENDURAPEARLSL25WLED757SASYTOPCMP, Bajaj cat part no. BRLEP 25W LED WH, Crompton cat part no. LSTS-25-CDL-M or equivalent make as approved by GE

S&F in replacement decorative wall light fixture made up of poly carbonate suitable for 10 watt LED lamp complete all as specified and directed by Engineer-in-Charge.

S & F in replacement Water tight bulk head fitting,comprision of connector galvanised cast iron back plate,weather proof enamelled gallery ,glass well,and including 10 watt LED lamp complete all as specified and directed by Engineer-in-Charge. Make:Havells cat part no : HEXAFT10WLED857SSYMBOPC, Bajaj cat part no. BIBWP 10W LED, Crompton cat part no. LBHP-10-CDL or equivalent make as approved by GE

S & F in replacement compact & decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1X10 watt fitting 2 ft version including LED lamp 10 watt complete all as specified and directed by Engineer-in-Charge. Make : Havells cat part no LUMILINEPLUSBS10WLED865SPCSS, Bajaj cat part no. BCLSB 10 WH, Crompton cat part no. LDL-10-CDL or equivalent make as approved by GE

S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer-in-Charge.

S&F LED lamp 9W for angle holder complete all as specified and directed by Engineer-in-Charge.

S & F in replacement of sub-main wiring with PVC insulated and un-sheathed 4 x 6.00 sqmm (Nominal Area) FR/FRLS stranded copper conductor drawn in and including PVC "medium quality" conduit as per size required including 2 x 6Sqmm (Nominal area) copper cable as earth contiunity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer-in-Charge. (Note : PVC cable and PVC conduit shall be ISI marked) Note :- Four length of 6 Sqmm cable and two length of 6 Sqmm earth cable along with PVC conduit will be measured as one running length

S&F in replacement sub main two single core PVC copper conductor unsheathed wire multi stranded 4 sqmm including cutting chasing and grouting PVC pipe including Tee, Elbow, Bend etc and including 4.0 sqmm copper conductor single core wire connected by common earth all as specified. Including 20 mm dia concealed PVC conduit, medium grade, ISI marked complete all as specified and directed by Engineer-in-Charge. Note :- Two lengths of 4.0 sqmm cable and one length of 4.0 sqmm earth cable along with PVC conduit will be measured as one running length

S&F in replacement sub main two single core PVC copper conductor unsheathed wire multi stranded 2.5 sqmm including cutting chasing and grouting PVC pipe including Tee, Elbow, Bend etc and including2.5 sqmm copper conductor single core wire connected by common earth all as specified. Including 20 mm dia concealed PVC conduit, medium grade, ISI marked complete all as specified and directed by Engineer-in-Charge. Note :- Two lengths of 2.5 sqmm cable and one length of 2.5 sqmm earth cable along with PVC conduit will be measured as one running length

S & F in repairs sheet metal enclosure for double door BDs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted TP & N 4 ways, 415 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer-in-Charge. Make : Havells / Legrand / Indoasian or as approved by GE

S&F in replacement Sheet metal enclouser for doble door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting VTPN 4 Way 415 Volt ISI marked 250Amps busbar stove enameled dust and vermin proof,IP:43 protection suitable for incorporation FP MCCB(V-Tech) N3 Frame upto 250A ,Isolators and including give connection with wire and cable etc complete all as specified and directed by Engineer-in-Charge.

S&F in replacement MCCB TP & N 100 Amps with breaking capcity 16kA ,Fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F in repairs MCB TP&N 63 Amps with breaking capcity 10kA ,Fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer-in-Charge.

S & F in replacement MCB ‘B’ series type suitable for 415 volts, AC supply 40 Amps, triple pole with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer-in-Charge.

S & F in replacement MCB ‘B’ series type suitable for 415 volts, AC supply 40 Amps, triple pole and neutral with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer-in-Charge.

S & F in replacement MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer-in-Charge.

M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on complete all as specified and directed by Engineer-in-Charge.

Dismantling and refixing of ceiling fans of any size including providing fan hooks clamps complete all as specified and directed by Engineer-in-Charge.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm complete all as specified and directed by Engineer-in-Charge.

Supply and filling in Sand for Cable protection complete all as specified and directed by Engineer-in-Charge.

Supply and lay standard size bricks subclass B type complete all as specified and directed by Engineer-in-Charge.

Supply and lay jointing and testing and commissioning in replacement of 35 Sqmm x 3.5 core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by Engineer-in-Charge.

Supply and fix 3 pin telephone socket RJ 11 with metal flush box having holes for 20 mm conduit entry for telephone connection complete all as specified and directed by Engineer-in-Charge.

S & F Rigid non-metallic PVC conduit 20 mm dia inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed by Engineer-in-Charge.

Supply and lay GI pipe 50 mm light grade for cable protection in walls trenches or any situation including clamp nut bolt etc complete all as specified and directed by Engineer-in-Charge.

Supply and Installation of AMR Enable Three Phase Meter with the following specifications: • AC Three Phase Four Wire, Tamper Proof, Static Meter of Class 1.0, 440 V, 50 Hz, 10 A-60 A,conforming to IS-13779 and relevant IEC standards with either inbuilt Low Power Radio Frequency (LPRF) communication facility in CyanConnode or equivalent Mesh network with default or rs 232 port or integrated modem communication and on demand display, billing data generation facility, anti-tamper features, Microprocessor and LED/LCD based circuitry. • Meter Should support the following data : 30 min instantaneous data for voltage, current, power factor, power, cumulative energy, cumulative apparent energy and frequency, 30 load survey data for energy, monthly billing survey for Cumulative Energy and Max Demand complete all as specified and directed by Engineer-in-Charge. MAKE: Capital, L&T, CyanConnode or equivalent make as approved by GE Note : Old existing single phase electric meters shall be deposited in E/M Store of GE SGNR

Supply and Installation of Data Concentrator Units (DCU) with the following specifications: • IP 51 rated Data Concentrator Unit (DCU) compatible for remote Automatic Meter Reading (AMR) solution and capable of communicating with the static energy Meter in the corresponding frequency band and with the data server through GPRS and shall have minimum data transfer rate of 9600 bps, internal memory to store data of 50 modules and shall be based on CyanConnode or equivalent Mesh network within 50 meter range complete all as specified and directed by Engineer-in-Charge. Make: Capital, L&T, CyanConnode or equivalent make as approved by GE

Hosting and Configuration of the Web based Software with following modules complete all as specified and directed by Engineer-in-Charge. : (i) Meter Data Management Module The meter data management module would be responsible for collecting the data from the concentrator and make the data available to the billing system. The meter data management system would capture and provide the following data: (a) 30 min instantaneous data from all the meters for seven parameters – Cumulative Energy, Cumulative Apparent Energy, Power, Current, Voltage, Power Factor and Frequency (b) Monthly and quarterly billing survey data for cumulative energy and max demand (ii) Billing Module The billing module would collect the data from the meter data management module, calculate the energy consumption, calculate billing determinant and make energy data / billing data available to admin and end users. The system would support occupation / vacation and billing reports. the software would be collecting data from DCU. The software would provide excess to staff as well as the occupant for the data. Make: Innologix, CyanConnode, L&T or equivalent make as approved by GE

Four year annual maintenance support for the software and GPRS provisioining (startng after one year of warranty period) complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement of meter box of size (0.9mX0.9mX0.2m) , thickeness 2.25 mm double door,made of CRCA sheet, single opening with lock arrangement ,transperent glass for meter reading, suitable for fixing 04 Electric meter & VTPN DB box including taking down existing electric meters , refixing them with four single core PVC copper conductor unsheathed wire multistranded 4 sqmm,properly painting on meter box complete and fixing in wall with suitable cutting,cement work etc complete all as specified and directed by Engineer-in-Charge. ---------------------------------------------------------------------------------------------- Note : A sum of Rs. 1,15,805.00 will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 37 & 39(R) (Schedule of Credit) of Tender document

M/s AKG Engineers & Contractors

KHANNA CONSTRUCTIONS

M/S BUDHRAM BISHNOI

M/s Tarun Traders