SPECIAL REPAIRS OF BLDG NO 65/1 TO 65/04 OF RMS AJMER AND PROVN OF SINGLE LIVING ACCN FOR HAV AND ORS AT RMS AJMER UNDER GE NASIRABAD

Amount

Taking down cement or cement lime plaster from stone / brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:6 on fair face of brick work or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L for brick work with fly ash bricks straight or curved on plan, any radius in half brick thick wall, built in CM 1:4 complete all as specified and directed.

M&L for Walling of random rubble, brought upto courses well bonded, bedded and solidly hearted, built in CM 1:6, complete all as specified & directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc 20 mm to lime or sand stone face and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses complete all as specified & directed.

M&L for machine cut Kota stone slab flooring 20-25mm thick over and including 15mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the smooth of the slab including rubbing & polishing complete all as spdspecified & directed.

Demolition of cement concrete (reinforced) of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work.

M&L providing PCC 1:3:6 type C1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps;seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate as in floor or laid under floor etc complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6,complete all as specified and directed.

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed plaster in cement mortar 1:3, complete all as specified and directed.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rect) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

All as per description of ser item No. 17.00 above but as in skirting over 10mm thick screeding in cement mortar 1:4 complete all as specified and directed.

M&L for coloured Glazed ceramic tiles in vertical surface of size 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over over and including 10 mm thick screed bed in cement mortar 1:4, complete all as specified and directed.

M&L 20mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

M&L for Steel work in tubular trusses & purlin including special shaped washer etc. complete using ERW or induction butt welded tubes Fe-410-W(Gde- E-250) quality- B , complete all as specified and directed.

M&L for pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and directed.

M&L for pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Dismantling timber scantling 40 Sq cm and over in section as in framed work in any position complete.

M&L for framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0, complete all as specified and directed.

Dismantling of existing unserviceable PVC water tank of capacity exc 500 ltr and not exc 1000 ltr each and removing from site, complete all as specified and directed.

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top), hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 20 mm dia, ISI marked, complete all as specified and directed.

S&F ball valve PTMT high pressure with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed 20 mm bore medium wt 210 gms, complete all as specified and directed.

Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

Description all as per Item No 29.00 above but 20 mm bore, complete all as specified and directed.

Description all as per Item No 29.00 above but 25 mm bore, complete all as specified and directed.

S&F water tubing 15 mm bore, medium grade, ISI marked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed.

Description all as per Item No 32.00 above but 20 mm bore, complete all as specified and directed.

Description all as per Item No 32.00 above but 25 mm bore, complete all as specified and directed.

Taking out old unserviceable water closet (squatt pattern) and S&F Vitreous China, Squatting pan Orissa pattern size 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) with Vitreous China ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe , including PCC (1:2:4) type B-1 for fixing of WC and making good the floor to match the existing, complete all as specified and directed.

Taking out old unserviceable wash down water closet and S & F vitreous china wash down water closet pan (pedestal pattern), white, including plastic white cover closed pattern with flat bottom and mild steel chromium plated hinge device including connections to drain (or outgoing pipe ) and to flushing pipe anti syphonage pipe etc complete all as specified and directed

S&F Plastic water closet seat, black, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repair PVC valve less , syphonic action otype flushing cistem, 10 litres capacity, low level, white, with inlet, ball valve, float, handle fixed with PVC rawl plug of suitable size, complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, white of size 550 mm x 400 mm flat back including waste pipe & brackets, CP coupling, complete all as specified and directed

S&F vitreous china wash hand basin, white of size 550 mm x 400 mm flat back including 32mm CP coupling and PVC waste down pipe & brackets complete all as specified and directed

S&F pilllar taps cast copper allloy capston headed, chromium plated, screwed down, high pressure with long screwedshank and fly nut, screwed for 15mm bore iron pipe, complete all as specified and directed.

S&F in repair wall Brass CP mixer with L bend for mixing hot & cold water screwed down for iron pipe and fixed complete all as spd and directed.

S&F in reapir Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

S&F in repairs bib taps, cast copper alloy with chromium plated crutch or butterfly handle, screwed down for iron pipe or for brass ferrule & fixed for 15 mm bore pipe, complete all as specified and directed.

S&F in repairs stop cock/ angle cock 15 mm dia cast copper alloy chromium plated screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union, complete all as specified and directed.

S&F in repairs PVC connection, heavy duty 15mm bore, 45 cm long with 2 Nos PTMT nuts of approved quality, complete all as specified and directed.

Taking out old unserviceable AC/PVC pipe and S&F 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

Taking out old unserviceable AC/PVC pipe and S&F 75mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius, complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed.

Taking out old unserviceable AC/PVC pipe and S&F 75mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls with PVC Clamps, complete all as specified and directed.

S&F 75mm bore PVC (SWR) vent cowl, complete all as specified and directed.

M & L for 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3), complete all as specified and directed.

Taking down unserviceable chowkhats or frame with shutters (without taking off shuters from the frames) of any description n. exc 1.50Sqm and removing from site and making good disturbed surfaces of wall in CM 1:3 (for windows and ventilators), complete all as specified and directed.

S&F for Pressed steel frames(125X60 mm) for doors with one or more rebates including ecessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

S&F rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing, conforming to Fe-410-W (grade E-250) quality 'A', complete all as specified and directed.

S&F 35mm thick 2nd class HW Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F second class HW, 35 mm thick, gauged and skeleton shutters, factory made open rebated (Three panels)and prepare to receive glass, gauge etc with out sash bar, edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. Size of members of shutter shall be as specified in SSR 1991 Part-I, section 8 clause Member shall be kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401, complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing. complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing with particle board core complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

S&F 150mm long aluminium, anodised, barrel tower bolt of extruded section, ISI marked, complete all as specified and directed.

S&F aluminium handle 150mm, cast type, anodised complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed to Door

S&F Steel window/ ventilator glazed and gauged (combination) with side hung/ top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete incl necessary AC/Cooler arrangement in window & guard bars complete all as as specified and directed.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed on wooden/steel frames with tinned tacks or galvanized wire staple, complete all as specified and directed.

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by the Engineer-in-Charge

S&F figured glass pin headed type, 3 mm thick and fixed with oil putty, size of glass n. exc 0.50 sqm in each pane, complete all as specified and directed.

S&F sheet glass ,ordinary quality, 3 mm thick and fixed with oil putty, size of glass n. exc 0.50 sqm in each pane, complete all as specified and directed.

M&L for newly plastered surface of wall and applying two coats of oil bond distemper over a coat of of primer over one coat of 1mm thick white wall putty, complete all as specified & directed.

M&L for prepration of new plastered/unplastered surfaces of ceiling and applying three coat of white wash completed all as specified and directed.

M&L for rendering in cement mortar (1:4) 10mm thick as in ceiling surfaces finished fair and even complete all as specified & directed.

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed

M&L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer, complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer, complete all as specified and directed.

M&L for newly plastered surfaces, applying two coat of cement base paint on walls over a coat of primer, complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3) complete all as specified and directed..

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in surface channel and drain etc. complete all as specified and directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, complete all as specified and directed.

M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth complete all as specified and directed.

M&L for 10 CM thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4. complete all as specified and directed.

S&F Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms)

M&L for Bottle trap 32 mm bore of PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms/ 40mm-270 gms) complete all as specified and directed.

Taking down existing unservicable treatment of any description including cement plaster/cement concrete of any thickness from roof surface cleaning of roof surfaces and and preparing it for further treatment and removing rubbish from the site up to 50 mtrs complete all as specified and directed.

M&L for screeding 10 mm thick in CM 1:4 on fair faces of RCC /stone patti roof surface finished fair & even without using extra cement even complete all as spescified and directed.

M & L for Plaster Rendering 15mm thick in CM 1:4 on fair faces of brick work or concerte surfaces whilst concrete is green mixed with WPC, finished even and smooth (without using extra cement) complete all as specified and as directed by the Engineer-in-Charge.

M&L for five layered APP modified polymeric water proofing membrane , 2mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3.00 Kg/Sqm applied with bonding material using blown type bitumen conforming to IS-702 grade 85/25 @1.20 Kg/Sqm over bitumen primer conforming to IS-3384 @0.40 Kg/Sqm with final coat of bonding bitumen grade 85/25 @1.20 Kg/Sqm over APP membrane with all overlaps complete all as specified and directed.

M&L for PCC 40mm thick (minimum consolideted thickness) type B-0, using 12.5 mm graded stone aggregate as in padding finished even and smooth wothout using extra cement with existing slope with V shaped grooves 6mm wide and10mm deep @0.40Sqm of each panel on top of padding and filled with mastic bitumen of 1:1 preparation complete all as specified and directed.

Supply, fabrication and fitting of modular kitchenwith cabinet and shelves out of 18 mm (OSL) solid PVC board of make Rajshri of denisity 600 kg/cum as specified and approved by Engineer-in-Charge for shutter cabinet and cupboard and similar include all necessary SS hardware such as hinges,Basket and handles complete all as specified and directed.

Excavation in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in hard/dense soil, complete all as specified

All as per description of serial item no. 92.00 above but depth exc 1.5m and not exc 3.0 m .

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil, complete all as specified

M & L for removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M & L for PCC 1:4:8 Type D2 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M & L for mild steel TMT bars of 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge.

M & L for RCC M-25 grade (design mix) using 20mm graded aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any) of foundation and plinth beams , and similar work, vertical or to batter, flat surfaces of concrete , surface is required to be fair finished complete all as specified and as directed by the Engineer-in-Charge

M & L for M-25 grade (design mix) using 20mm graded aggregates as in columns, pillars, piers, posts and struts complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions, rectangular or polygonal surfaces of concrete , surface is required to be fair finished. complete all as specified and as directed by the Engineer-in-Charge

M & L for RCC M-25 (design mix) using 20mm graded aggregates as in Roof beams, lintel beams/bands, cantilevers, bressummers, lintels over 1.5m span, chajjas etc complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to sides and soffits of floor or roof beams, soffits of lintel beams/ bands, chajjas, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, etc., flat surfaces of concrete , surface is required to be fair finished. complete all as specified and as directed by the Engineer-in-Charge

M & L for RCC M-25 (design mix) using 20mm graded aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), flat surfaces of concrete , surface is required to be fair finished. complete all as specified and as directed by the Engineer-in-Charge

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, as roughed finished surface of concrete complete all as specified and as directed by the Engineer-in-Charge

M & L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge

BLANK

Supply only Integral waterproofing compound, ISI marked.

M & L for Plaster Rendering 15mm thick in CM 1:4 on fair faces of brick work or concerte surfaces whilst concrete is green mixed with WPC, finished even and smooth (without using extra cement) complete all as specified and as directed by the Engineer-in-Charge.

M & L for preparing new plastered or unplastered surface of walls and applying three coats of white wash as on walls complete all as specified and directed.

M & L for rendering 5mm thick in cement plaster 1:3 on fair faces of brick work or concrete surfaces , in ceilings, finished even and smooth without using extra cement, in ceilings complete all as specified and as directed by the Engineer-in-Charge

M & L for machine cut kota stone slab as in shelving/ window cills or steps 25mm thick in single piece over 15mm thick screed bed CM (1:6) incl necessary bull nosing fixed to wall and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing on both face complete all as specified and as directed by the Engineer-in-Charge

M & L for 75mm thick cement concrete type D-2 1:4:8 using 40mm graded aggregate , as in sub base. complete all as specified and as directed by the Engineer-in-Charge

BLANK

BLANK

BLANK

S&F IInd Class Hard wod small fittings such as brackets of any type, latch and hinges blocks , shaped door and window stops and the like, incl all necessary labours; article n.exc 200cu.cm each

BLANK

S & F IInd class hardwood chowkats and frames Plain, solid, straight, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints all as specified. complete all as specified and as directed by the Engineer-in-Charge

M & L for 18/19mm thick prelaminated MDF board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed by the Engineer-in-Charge

S & F megnate and striking plate as per sample complete all as specified and as directed by the Engineer-in-Charge

S&F continuous piano hinges mild steel bright finish and width of flaps 30mm when open.

S&F aluminum anodised hapse & staple 100mm size.

Supply and fixing for ISI Marked 100mm long aluminium handle, cast type, anodized complete all as specified and as directed by the Engineer-in-Charge.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors and fixed to wall with clamps complete all as specified and as directed by the Engineer-in-Charge

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge

S & F 110mm bore PVC (SWR) bends of any radius, complete all as specified

S & F 110mm bore PVC (SWR) vent cowl, complete all as specified

M & L for PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge

S & F Vitreous China squatting pan, `Orissa` pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) with long body PVC SWR suitable 'P' or 'S' trap complete all as specified and as directed by the Engineer-in-Charge.

S&F 10 ltrs capacity PVC Valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets low level flushing cistern and connections to pipes and incl suitable flushing pipe for connection into Orissa WC, if any all as specified. complete all as specified and as directed by the Engineer-in-Charge

S & F of 15mm size PVC connections with PTMT nuts of length 450mm complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top), hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S & F of 15mm bore dia bib Bib taps, cast copper alloy fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engineer-in-Charge

S & F 15mm bore dia stop valves/angle cock, cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge

S & F 15mm bore dia stop valves/angle cock, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge

S & F brass chromium plated swivel shower rose 125mm size, including fixing to steel pipe or union complete all as specified and as directed by the Engineer-in-Charge

S & F Tubular towel rail of Brass Chromium plated, 20mm dia, D type, 60cm long between flanges including Chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed by the Engineer-in-Charge

S & F for brass chromium plated soap dish, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge

M & L for hardcore of broken stone or boulders gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and remmed to a true surface, complete all as specified

S&F Aluminium alloy anodised butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

S&F fancy type 20mm dia aluminium curtain rods powder coated fixed to bracket completed all as spd & directed.

S&F decorative type knobs with bracket of MS powder coated fixing at end of pelmet rod complete al as spd & directed.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

M&L for 100 mm thick PCC (1:3:6) type C2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for factory made 60mm thick reflective type machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 50 mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

Material and labour for PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate in bedding to RCC drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L for 150 mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed.

Excavation over areas not exc 1.5m deep and getting out in soft/loose soil all as specified and as directed.

M&L for cement concrete 1:2:4 type B1, using 20 mm graded crushed stone aggregate as in benching, rounded or chamfered on edges all as specified.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as copings, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified.

M&L for PCC 1:2:4, type B1 using 20mm graded crushed stone aggregate as in manholes covers, cover slabs of drains and similar works including placing in position and set in CM (1:6) complete all as specified & as directed.

Construction of soakage well, excavation in any type of soil, foundation in PCC 1:3:6 walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber, screen chamber made of brick masonry work in CM 1:6, RCC cover slab in M-25/SFRC cover interconnecting pipes of RCC/DWC complete filled with brick bats of size 2.4 m dia and 3 m deep, complete ass as per drg No. CEBZ/TD/78/2011 sheet 1/2 & 2/2

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc complete all as specified & as directed.

Disconnecting unserviceable sub main wiring/service connection of any size and including conduit and accessories and removing from site and making good the disturbed surfaces complete all as specified & as directed.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor complete all as specified & as directed.

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame for suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for the following, complete all as specified and directed:

One light point/bell point controlled by one way 5 Amps SP switch

One ceiling fan/exhaust fan point controlled by one, one way switch.

One 5 pin 5 Amps socket outlet on same board with other switch

One 5 Pin 5 Amps socket outlet on independent board with other switch.

One light point controlled by two 2-way switches

All as per item No 161.00 above but with 2.5 Sqmm cross sectional area electric cable for 15 Amp socket outlet on independent board, complete all as specified and directed

S&F modular stepped type ceiling fan regulator, 230 volt AC, 2 module, complete all as specified and directed.

S&F of modular switch 1 way 6/10Amp , 1 module, complete all as specified and directed.

S&F of modular switch 1 way 16Amp, 1 module, complete all as specified and directed.

S&F of modular switch 2 way 6 Amp, 1 module complete all as specfied and directed.

S&F of modular bell push, 6 Amp, 1 module, complete all as specified and directed

S&F of modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F of mdoular socket 6Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm.

S&F door bell ding dong type electric 230 volts AC , single phase, complete all as specified and directed.

S&F lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

S&F box type LED tube light fitting in acrylic linear tube 1x 20 watt, 230V complete with bipin holders,LED power driver, connector block, and LED Tube rod 20 watt. Make :- Havells/Bajaj/Philips/Crompton as Approved by AO.

S&F LED mirror Light fitting, 1X 10 W, attractive wall/ceiling mounted type with mettalic channel and white reflector, suitable for mirror light fittings with complete with all accessories pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified & as directed. Make :- Havells/ Bajaj/ khaitan/Usha as Approved by AO.

S & F wall mounted decorative luminarie fitting suitable up to 10 watt LED lamp B-22 base complete all as specified and directed. Note: LED lamp 9/10 watt shall be measured and paid separately. Make :- Havells/ Bajaj/ khaitan/Usha as Approved by AO.

Supply and fixing LED lamp 9/10 watt , 230 volts , 50 Hz, B-22 base for fixing in lamp holder and wall mounted decorative light fitting complete all as specified and directed. Make :- Havells/ Bajaj/ Philips as Approved by AO.

S&F LED bulk head luminaire 1x 10 W bulk, IP 65 protection complete with all accessories and including connecting up with three core copper conductor cable complete all as specified and directed. Make:- Bajaj/Havells/CG as Approved by AO.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp and street light bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. Make- Havells Cat Part No ENDURACITYLITEPLAT PLUSSL35WLED757SASYBOPC or equivalent model from Surya/Control& Switchgear/Bajaj as Approved by AO.

Disconnecting and taking down existing electric meter and refixing the same electric meter, connecting, testing and sealing properly and making good disturbed surface of walls etc complete all as specified & as directed.

Taking down existing ceiling fan , dismantling blades and refixing after cleaning incl conecting up with three core flexible cable from ceiling rose to fan.

Taking down existing geyser and refixing after cleaning and descaling all as directed. .

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

S&F of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S&F of MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'C' curve complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing .

S&F exhaust Fans AC single phase 230/240 volts of size 300 mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. Make: Havells/Bajaj/Crompton

S&F of ventillation fan 250mm sweep non metallic white colour including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. Make: Havells/Bajaj/Crompton

Supply and fixing LED box type tube light fitting 20 watt made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body , PC diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired complete all as specified & as directed. Havells/Bajaj/Philips/Crompton as Approved by AO.

Supply & fixing ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy. Make: Crompton/Bajaj/Havells.

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 6 sqmm multi stranded copper conductor cable complete all as specified & as directed.

M& L for TV Socket incl PVC conduit and co axial cable wire.

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

Supply and laying including jointing, testing or fixing or passing through pipe, trench or duct commissioning and testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade size 16 sqmm, 2 core complete all as specified and directed by Engineer-in-Charge.

S&F water tubing 20 mm bore, medium grade, ISI marked galvanized with all fittings, laid in trenches, complete all as specified and directed.

S&F water tubing 40 mm bore, light grade, ISI marked galvanized with all fittings, laid in trenches, complete all as specified and directed.

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

MAHARANI CONSTRUCTION

M/s AKASH CONSTRUCTION CO.

M/s SUNIL ENTERPRISES