SPECIAL REPAIR TO BLDG NO DS-3 OF SINGLE JCOs ACCN OF 194 MED REGT, BLDG NO P-89 GOVT MARRIED ACCN AT CHANDIGARH LINE OF 16 RAJ RIF AND BLDG NO AC-3 (SINGLE JCOs ACCN) AT 633 SATA BTY (H/M) UNDER GE (N) MEERUT CANTT

Amount

Roughning of existing PCC flooring by means of light hammering/cheaseling etc to receive screed bed for placing tiles complete all as specified and directed.

Taking down cement or cement lime plaster, any description on stone walls etc including raking out joints hacking for key, scrubbing down with water, etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, such as sunken floor, roof padding etc complete all as specified and directed.

M&L 50 mm thick averaging thickness PCC (1:2:4) type BO, (using 12.5mm graded stone aggregate) as in roof padding finish fair & even complete all as specified.

Surface Preparation: The surface to receive the treatment shall be thoroughly free of laitance, scales, oil or any other loose material. It should be made free of any sharp objects. Cleaning of PCC shall be done with wire brushing to attain smooth levelled surface. Cracks shall be rectified, filled using dual shrinkage compensated Repair Mortar and dried for 72 hours before laying the liquid applied membrane. Grout: Providing Chemical injection treatment in the form of pressure grouting to the construction joint and cracked portion at 1m c/c by injecting cement slurry mixed with dual shrinkage compensated cementitious grout Injection grout additive, in the required consistency through the pre fixed PVC nozzles in the 18 mm dia holes, fixing of PVC nozzles with instant setting cement. Angle fillets/Coving: Providing and making of fillet, 50mm x 50mm on sharp corner of terrace with cement sand polymer mortar (add “multipurpose mortar”, 10% by weightofcement). First apply the bonding coat of Multi-Purpose Polymer 5-10% diluted in water and add to cement slurry. Apply the bonding slurry and apply the polymer mortar over the sharp edges. Note: Grouting will be done when and where ever required.

Treatment of pipe entry points: Preparing the inside surface of core and PVC /MS Pipe by roughening using suitable Sand paper to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Packing the gap using free flowable non shrink cement polymer based grout up to the surface of the bore while the bonding agent is in tacky state. the periphery of PVC pipe should be sealed with Hybrid PU Sealant or dual shrinkage compensated Micro concrete. Note: Will be done when and where ever required. Application of Asian Paints two component Epoxy Primer (Resin & Hardener) on the cleaned surface for bonding of Polyurethane with the existing concrete surface. 33 % water dilution is recommended with the pure mixed primer. The primer mixing ratio will be 1:3(Resin:Hardner) Supplying, providing and applying waterproofing treatment to Podium area with single component highly elastomeric seamless cold applied modified PU coating complete as per manufacturer’s specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have a dual combination of 280% elongation. Material coverage 1.2kg /sq.mt. (Note: Contractor is required to deposit 100% CA quantity to the Engr-in-Charge, within 15 days of acceptance of contract.

Supply only liquid integral water proofing compound complete all as specified and directed.

M&L non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for light shade, vitrified tiles, 10mm thick (square/rectangular) area of each tiles exceeding and including 0.36 Sqm but not exceeding 0.42 Sqm, in flooring set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over and including 15mm thick screed bedding in CM (1:6) complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 300 x 200 x 7mm/450 x 350 x 7mm thick on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match over 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L 18- 20mm thick pre-polished green marble (Udaipur green) (of any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for rounding to edges of stone slabs two edge full round,such as in steps,cooking platform and other similar situation complete all as specified and directed.

M&L Stone Slab 50 mm Thick cement mortar 1:4 dressed true and square, in one length not less than 60 cm and n.exc 120cm in copings, window cills, chajjas, sunshades, etc, punched dressed on exposed faces and self faced on the embedded unexposed beds and joints ; exposed edges round or chamfered as directed, set, jointed and pointed in mortar as in plinth protection complete all as specified and directed.

M&L for rendering 15mm thick cement plaster 1:6 on stone masonry surface or surface other than fair face of brick work surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick in (1:3) cm on fair faces of ceiling complete all as specified and directed.

M&L for applying 15mm thick rendering using ready mix plaster bags in CM 1:4 on brick/concrete surfaces of external walls finished even and fair, using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, complete all as specified and directed. Make :Ultratechrediplast, Brila Aerocon. Note:- Supply only water proofing compound shall be measured and paid separately. (Note: Contractor is required to deposit ready mix bags for 100% CA quantity to the Engr-in-Charge, within 15 days of acceptance of contract.

M&L for preparing new plastered or un-plastered surfaces and applying three coats of white wash on ceilings complete all as specified and directed.

M&L for preparing old plastered or un-plastered surfaces and applying one coat of white wash on ceilings complete all as specified and directed.

M&L for preparation of new plastered surface of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper over one coat of primer using roller for painting complete all as specified and directed.

M&L for preparation of old surface after complete removal of existing treatment by mechanical means and applying 2mm thick wall care putty over one coat of primer and making the surface smooth and applying two coat of oil emulsion distemper using roller for painting complete all as specified and directed.

M&L for preparation of new plastered surface of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coats of Acrylic Exterior Emulsion paint over one coat of primer using roller for painting complete all as specified and directed.

M&L for preparation of complete removal of existing treatment from old plastered surfaces of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coats of Acrylic Exterior Emulsion paint over one coat of primer using roller for painting complete all as specified and directed.

Taking down chowkats or frame of any description not exc 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frame of any description tion exc 1.5 Sqm each and not exc 4 Sqm (without taking off shutters from the frames) complete all as specified and directed.

S&F MS angle iron framed work as in doors or gates of angle or other section conforming to Fe-290 (Gde E-165) with gusset plates, rails, braces, etc complete including hanging also fastening and fixing complete all as specified and directed.

S&F 35mm thick, second class hard wood in glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge.

S&F 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

Eco- 4000 Series Windows : M&L for Providing and fixing Windows, Ventilators fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality,Galvanized as per IS 277 with Zinc of 120 grams/ Sqr. Mtr.) with total coated thickness of 0.60 mm Paint specifications : Coated Sections should be coated with Primer Coat of Epoxy Primer of 5-7 microns thick, finish painted with Polyester paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns, or Powder Coated with pure Polyester Powder up to 50-60 microns thick. Dimensions of Sections : Sections for Frame should be of 72mm X 50mm, Section for Mullion should be of 72mmX50mm, Section for Shutter Frame should be of 47mm X 20mm, Section for Fixed Glass Bead should be of 12mmX12mm, and Section for Fly mesh should be of 40mm X 20mm. Fixing Details : Section for Frame Glazed Shutters and Mesh Shutters should be cut to length and miter joined with Polypropylene Corner Brackets, Mullion Section should be joined to the Frame/ Mullion using Nylon cap. Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter and Fixed Glass. Rubber Gasket should be used around Fly mesh to fix Mesh in Mesh Shutter. Accessories : Each Glazed Shutter should be provided with S.S. Pivot Hinges-1set, Seccolor Handle &Seccolor Stay. Glass : Glazed Shutter and Fixed Glass portions should be provided with a glass of 4/5mm Plain Float Glass. Mesh : Mesh Shutter should be provided with a Stainless Steel 32 gauge Fly mesh of 304 grade with 144 holes per sq. Inch. Windows should be provided with Grill made of 10mm sq. MS Bars welded to at 150mm centre-to-centre, 6mm X 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws. Window Frame should be fixed to brick/concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames. Note. The item includes everything as, painting the surfaces , fixing, all necessary accessories, glass, mesh, etc, all as per given specifications, complete all as specified and directed by GE. Make- NCL Altek and Sec color Ltd, Bharat Win Solutions.

Taking down old existing water proofing treatment from the top of RCC/ arch slab, including taking down existing PCC padding or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish off the premises complete all as specified and directed.

S&F 3mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to wooden door Shutters/aluminium sliding shutters complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as per specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Make - Rajshree, Eco Cell, M/s TVL Engineers Pvt Ltd, New Delhi (Floresta) Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F for 35mm thick Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Make- Rajshree, Eco Cell, M/s TVL Engineers Pvt Ltd, New Delhi (Floresta). Note: stainless steel butt hinges and necessary S S screws shall be paid separately.

S&F 300 mm length of bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cost or extraded sections and fixing bolts and sliding bolts of extraded sections or cost aluminium alloy complete all as specified and as directed.

S&F 150mm size, aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

All as per item No 36.00 above but 100mm complete all as specified and directed.

S&F aluminium, anodised barrel tower bolt of extruded section and fixed 200 mm of size complete all as specified and as directed.

All as per item No 38.00 above but 150mm complete all as specified and directed.

S&F 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel spring complete all as specified and directed.

S&F stainless steel butt hinges, medium weight, cold rolled, mild steel of size 100 mm ,incluing necessary SS screws, complete all as specified and directed.

S&F 25mm dia, powder coated, fancy type, aluminium decorative tubular curtain rod with decorative ball type side brackets, complete all as specified and directed.

S&F in repairs, 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination, fixed with screws to timber frame work in cup boards, rebated or flat edged complete all as specified and directed.

M&L for 6mm thick external teak wood lipping fixed to18/19mm thick block or Veneered particle boards with nails complete all as specified and directed.

S&F continuous (piano) hinges, mild steel bright finish or electrogalvanised, width of flap 40 mm complete all as specified and directed.

S&F hasp & staples 125mm in size, safety type aluminium anodised fixed with screws complete all as specified and directed.

S&F ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F white glazed earthen ware vitreous china wash hand basin of size 550x400mm with and including CI brackets, 32mm bore brass CP waste coupling Inlet/ outlet, PVC flexible pipe, 600mm size for 15 mm bore pipe with brass nut and washers etc complete all as specified and directed. Make – PRAYAG SPA - Cat No-4641, CERA CADAL Cat No-S2040121.

S&F in repairs, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed. Make – PRAYAG VINTAGE - Cat Part No-503, CERA CIENA PREMIUM Cat Part No-B1010102, PEARL CAT No C-001/CLR.

S&F chromium plated over head shower 100mm dia round shape single flow (ABS Body chrome plated with Gray face plate) with rubit cleaning system complete all as specified and directed. Make - CERA F7010111SS, PRAYAG CAT NO BOS-42.

S&F in repairs, 15mm brass chromium plated fancy type bib cock with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make – PRAYAG CASA - Cat Part No-9206, CERA OCEAN Cat Part No – QTF2006151 HTF3001151, Pearl Cat Part No TTS-1060.

S&F in repairs, 15mm stop valves, fancy type brass chromium plated for iron pipe or for unions and fixed to 15mm bore pipe, complete all as specified and directed. Make – PRAYAG - Cat Part No-9210, CERA OCEAN Cat Part No-QTF2006202 HTF3001202.

S&F in repair 15mm pillar taps, brass chromium plated fancy type with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe or for union and fixed to 15mm bore pipe, complete all as specified and directed. Make – PRAYAG CASA - Cat No-9204, CERA OCEAN Cat No-QT F2006101 HT F3001101, Pearl Cat Part No-MAP-902.

S&F 50mm, low density polyethylene pipes (LDPE) of pressure rating 6 kg/Sqcm fixed complete to walls, ceilings or in floors etc in repairs complete all as specified and directed.

S&F brass chromium plated, tubular towel rail 20mm dia, D type, 60 cm long between flange, fixed in repairs complete all as specified and directed. Make:-Prayag Cat No BA-01,Cera Cat Part No:F5004105.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair, kitchen sink with drainage board made of stainless steel 1mm thick including supply and fixing 32mm CP waste coupling, plug, washer, 32 mm bore and 60cm long PVC waste pipe including cantilever brackets made of mild steel duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning in ends of brackets to errecting stand into wall, over all size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed. Make:- Nirali, Blue Star.

S&F in repairs, 1mm thick, stainless steel plate rack of size 120cm x 90cm x 18cm complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

S&F CPVC water tubes, medium grade, incl all necessary CPVC fittings, as per site requirement like elbow, tee, nipple, socket, union etc and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed. Make - PRAYAG, Finolex, Kisan.

S&F CPVC water tubes, medium grade, incl all necessary CPVC fittings, as per site requirement like elbow, tee, nipple, socket, union etc and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed. Make - PRAYAG, Finolex, Kisan.

S&F rotational moulded polyethylene water storage tanks of capacity 500 Litres (Cylendrical vertical with closed top), triple layer, white reflective colour, hoisted and fixed in position all as specified in SSR-Part-I including disconnecting and removal of old U/S PVC tank, complete all as specified and directed. Make:- Tuff, Sintex neo, Plasto.

S&F in repairs 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) complete all as specified and directed.

Dismantling of PVC pipes jointed in neat cement mortor and taking out of trenches if required complete all as specified and directed.

S&F 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors/walls complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, fixed to walls complete including fixing clamps complete all as specified and directed.

S&F PVC (SWR) bends of any radius with oval and access door of 75mm dia complete all as specified and directed.

S&F PVC (SWR) bends of any radius with oval and access door of 110mm dia complete all as specified and directed.

S&F PVC (SWR) vent cowl of 75mm dia complete all as specified and directed.

All as per item No above 71.00 but 100mm dia complete all as specified and directed.

S&F PVC (SWR) Floor/ Nahani trap with grating of diameter of outlet 75mm including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete fixed all as specified and directed.

S&F PVC (SWR) branch piece single (single ‘Y’) equal or unequal suitable for 75mm bore pipe complete all as specified and directed.

S&F PVC (SWR) branch piece single (single ‘Y’) equal or unequal suitable for 110mm bore pipe complete all as specified and directed.

M&L cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in foundations filling and mass concrete complete all as specified and directed.

M&L for fair finished 60mm thick Machine pressed precast concrete interlocking paver block (50% Red and 50% Yellow) with grey cement and pigment any shape, size and colour conforming to IS 15658- 2006 M-35 grade including 25mm thick sand cusion below tiles complete all as specified and directed.

Demolition cement concrete (unreinforced) in ground floor and pavings not exc 15cm thickness (below or above ground level) complete as specified and directed.

M&L for taking down, chipping and removing the loose, spailt, damaged cement concrete, cement mortor surfaces of RCC columns, beams, walls, chajjah etc and exposing the reinforced cement, wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthen the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing polymer modified cement and quartz sand mortor in CM 1:3 mix , 40mm thick in two coats, using polymer SBR Latex or of equivalent make as approved by GE @ 5 Ltrs per 50 Kg bag of cement complete all as per manufacturer's Specifications/instructions complete all as specified and directed. Note:- New reinforcement, Welded wire fabric will be measured and paid separately. Make: Dr. Fixit/Sunanda/chemestik/Fosrok.

S&F welded steel wire fabric, cut to length, fixed to steel members/reinforcement steel, weigh per Sqm not exc. 4 Kg complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed. Make:-PBC, ECO and EXPERT.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick cement concrete 1:4;8 type D2 (using 40mm graded stone aggregate) in subbase of floor complete all as specified and directed.

M&L for coloured chequered cement concrete tiles 30 cm x 30 cm, 25 mm thick set, jointed and pointed in neat cement slurry including 20 mm thick screed bed in CM 1:4 complete all as specified.

Dismantling asbestos cement (corrugated, semi corrugated) sheets including ridges as in roof covering complete all as specified and directed.

M&L for pre painted galvalume aluminium zinc coating (AZ-150) GI based corrugated Steel sheet 0.50 mm thick of green colour having tensile strength of 550 Mps, as in roof covering/cladding to wall fixed with self tappingscrewes complete all as specified and directed.

M&L for pre painted galvalume aluminium zinc coating (AZ-150) GI based plain Steel sheet 0.50 mm thick of green colour having tensile strength of 550 Mps as in roof covering/cladding to wall/ridge fixed with self tappingscrewes complete all as specified and directed.

M&L for MS angle as in roof trusses (framed), trusses, purlins crane gantries, rails and fastening and heavy brackets framing (beam, tee, angle, channel or flat sections) including distance pieces cleats etc conforming to Fe 410 W (Gde E 250) quality B complete all as specified and directed.

Supplied and fixed Tee grid suspension system of size 600 mm x600 mm type-1 made out of rolled framed hot dipped galvanised steel zinc coated of not less than 120 gm/sqm ,main runner shall be 0.3 mm thick of section 24 mmX33 mm cross runner 0.3 mm thickof section 24 mmx25 mm,wall angle shall be 0.63 mm thick of section 24 mmx24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod ,system exposed portion shall be pre painted polyster coated in off white/white in colour complete with material,fixing, jointing etc all as per manufactures instructions complete all as specified and directed. (Make:- Armstrong or of equivalent make as approved by GE).

Supplied and fixed fibre cement coloured textured designer ceiling board 4mm thick of size 595x595 mm conforming to IS : 14862 & IS : 2380 Part-XIV fixed to timber / GI / Aluminium frame work with screws/clips complete all as per manufactures instructions and as directed. (Make:- Armstrong or of equivalent make as approved by GE).

S&F, in repair, vitreous china wash down water closet pan (Pedestal pattern), white with 'P' or 'S' trap (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. and including necessary Seat Cover Snow White as per required specification complete all as specified and directed. Make:-Prayag Cat Part No 4018 Garnet EWC, Cera Cat Part No S1059104/3.

S&F gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, 20mm bore complete all as specified and directed.

S&F brass chromium plated soap dish complete all as specified and directed. Make- Prayag Cat Part No BA-5S, Cera Cat Part No F5004106.

S&F mixer pillar tap, cast copper alloy with capstan head, chromium plated, fancy type, screwed down, high pressure, for hot and cold water, 15 mm bore complete all as specified and directed. Make:-Cera Cat Part No F2004461, Prayag Cat Part No 9350-N, Pearl Cat Part No GPR-882.

S&F toilet paper holder of brass chromium plated conforming to the samples kept in the office of Engineer-in-Charge complete all as specified and directed. Make:-Cera Cat Part No F5004110, Prayag Cat Part No BA-08.

S&F towel ring 200 mm dia chromium plated fancy type conforming to the sample kept in the office of GE complete all as specified and directed. Make:- Prayag Cat No BA-02, Cera Cat Part No F5004105.

S&F 8mm dia, brass chromium plated health faucet with 1 meter long flexible hose and wall hook complete all as specified and directed.

S&F corner glass shelf with bracket complete all as specified and directed. Make- Prayag Cat No BEA-52 or of equivalent make as approved by GE.

Excavating in post holes (or similar holes) each not exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing urplus soil to a distance n exc 50 m and making good surface as in soft/loose soils complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling stone slab and tiles of any description or thickness in floors,aprons etc complete all as specified and directed.

M&L for PCC 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) for filling into sunken floors etc. complete as specified and directed.

M&L for PCC 1:2:4 type B1 using 20 mm graded stone aggregate, 40mm thick, and applying layer of doctor fixit over the PCC surface, complete all as specified and directed.

M&L for water proofing plaster for sunken portion in CM 1:3, 15 mm thick with integral water proofing compound at the rate of 3% by weight of cement and finishing the surface even and smooth without using extra cement complete all as specified and directed. (WPC will be measured and paid seperately).

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg Per Sqm including cleaning surfaces etc complete all as specified and as directed.

Taking down shutters of description exc 1 sqm and not exc 2 sqm each complete all as specified and directed.

Re-fixing in the same opening of shutters of any description exc 1 Sqm and n exc 2 Sqm each complete all as specified and directed.

S&F in repairs, vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, 'P' or 'S' trap (excluding flushing cistern and flush pipe) complete all as specified and directed. Make – PRAYAG - Cat Part No-4055 23”, CERA CALINA Cat Part No-S3010102.

M&L for 18-20 mm thick size 550X550 machine cut kota stone slab flooring over cement screed base laid and jointed with grey cement slurrty mixed with pigment to match the shade of slab including rubbing and mirror polishing for thread in stair case and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 20-25 mm thick kota stone slab as in riser/skirting/dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing andincluding 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

S&F MS pipe for stair case raillings complete all as specified and directed.

M&L rendering 15 mm thick and surface of brick work in cement mortar 1:6 on wall of brick work of concrete surface, finished even and smooth (with out extra lime or cement) complete all as specifed and directed.

S&F glazing with sheet, 3mm thick, ordinary quality and glazing with oil putty and glazing pins in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

M&L preparation of old painted wood and wood base surfaces of any description, not otherwise described over 10 cm width or girth and painting with a coat of sythetic enamel paint complete all as specified and directed.

S&F in repair 150mm size, aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repair aluminium, anodised barrel tower bolt of extruded section and fixed 200 mm of size complete all as specified and directed.

S&F in repair 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel spring complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and directed.

M&L for plain cement concrete M-10 Nominal Mix (1:3:6) Type C1 (using 20 mm graded stone aggregate), as in lintels upto 1.5 m clear span, cills, steps,seismic and other similar bands, plinth course, string courses, lacinng courses, parapets and railings, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section, in any position complete all as specified and directed.

All as per item No 122.00 above but as in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size, complete of size 3.00 M dia X 4.5M effective depth complete all as specified and directed..

Septic tanks, excavation, in ordinary soil, foundation each in PCC 1:2:4, brick work in CM 1:4, RCC Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame Vent shaft and sludge chambers etc., complete for 25 users complete all as specified and directed.

Taking down carefully any type, battens or conduit point wiring with or except conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, pendent light fittings, MCBs / isolators, fan regulators, tube light fittings etc removing material from site and making good disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as specified & directed.

M&L for surface point wiring with 1.5 Sq mm (nominal cross section area) single core, 1100 volts grade, multi stranded PVC insulated, unsheathed copper conductor,FR, cable in and including in stove enamelled steel conduit 20 mm dia or higher medium grade ISI marked complete with all steel conduit accessories / fittings and sunk pressed (1.2 mm thick) steel terminal switch boxes with 3 mm thick plastic laminated hard glossy surface sheet top cover, including earth wire continuous of PVC insulated, unsheathed 1.5 Sq mm copper conductor, PVC insulated connected to all fittings, sunken boxes and common earth, earth dolly. Plastic laminated sheet screwed with brass screws, cup washers complete all as specified and directed for the following :-

One tube light/Bulb/street light point controlled by one, one way switch 05/06 Amps.

One fan point controlled by one, one way switch 05/06 Amps.

One 3 pin 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 amp switch.

One 3 pin 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 amp switch.

One bell point controlled by one, one way switch 05/06 Amps complete all as specified and directed.

All as per serial item No 127.03 here-in-before but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15/16 Amps socket outlet point on independent board.

S&F Switch piano flush type, 05/06 Amps single pole, one way 240 volts complete all as specified and directed.

S&F in socket outlet 5 pin, 05/06 Amps flush type 240 volts complete all as specified and directed.

S&F in socket outlet 3 pin, 05/06 Amps and 3 pin 15/16 Amps (2 in 1 multipurpose) 240 volts complete all as specified and directed.

S&F Switch piano flush type, 15/16 Amps single pole, one way 240 volts complete all as specified and directed.

S&F bell push flush type, 5 Amps, 240 volts complete all as specified and directed.

S&F bell, AC, 230 volts, single pole complete all as specified and directed.

Supply and fixing lamp holder (Angular/Striaght), insulated body, with back plate complete all as specified and directed.

S&F LED lamp 9/10 watt fixed in lamp holder complete all as specified and directed. Make - Crompton/Havells/C&S/Surya/Philips.

S&F decorative wall mounted LED tube light fitting 20 watt with polycarbonate housing with all accessories and fixing material complete all as specified and directed. Make - Crompton/Havells/C&S/Surya/Philips.

S&F decorative wall mounted LED tube light fitting 10 watt with extruded polycarbonate integegrated lamp and driver with opal diffuser and decorative end plates complete with all accessories and fixing material complete all as specified and directed. Make - Havells, Cat ref - LUMILINEPLUSBS10WLED865SPCSS,, Crompton, Cat ref - LCTLN-10CDL, C&S, Cat ref - Nakshatra/10W.

Supply and fixing 1x25W/35W LED building security light energy saving & environmental friendly long life luminaire with high power LEDs as light source and electronic driver including security brackets of 32 mm dia GI pipe medium grade upto 1.2mtr long bend o shape at 100-200 degree including flat iron clamps and suitable nuts and bolts grouted in wall including all material required for fitting complete all as specified and directed. Make - Havells, Cat ref - ENDURAPREALSL25WLED757SASYTOPCMP, Crompton, Cat ref - LSTS - 25-CDL-M, C&S, Cat ref - INDUSE/25W.

S&L XLPE insulated armoured heavy duty electric power cables with aluminium conductor 1100 volts grade cross sectional area of 10 Sqmm 2 core complete all as specified and directed.

All as per item No above 139.00 but 35 Sqmm 3.5 core complete all as specified and directed.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundations etc, etc or for laying of cable or Pipe and cables etc. but not exceeding 10 sqm on plan and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Removing excavated material not exceeding 50m and dispositing where directed at a level not exceeding 1.50 m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

M&L for GI light grade tubing 40mm dia laid in trenches, road crossing, passing through pipe or laid in wall/pole complete all as specified and directed.

Supply and spreading clean fine dry sand in trenches for cushioning of under ground cable/cable duct complete all as specified and directed. (Note: Punned thickness shall be measured for the purpose of paymnet).

M&L for fly ash brick protection length of brick shall be laid across the length of cable complete all as specified and directed.

Supply & fixing of ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified and directed.

Taking down carefully unserviceable sub main wiring of any size and type, removing material from site to store for keeping in safe custody for reuse at site making good the disturbed surfaces of walls, ceilings etc including two coats of white/colour washing/distempering etc to match the existing complete all as specified and directed.

M&L for sub main wiring with 06 Sq mm (nominal cross section area) two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed copper conductor cable with and including continuous earth wire of size 6 Sqmm nominal roll cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25mm dia, medium grade with all conduit accessories/ fittings, brass screws, washers etc and connected to common earth dolly including all cutting/chases etc in wall, making good to walls etc including two coats of white/ colour washing/ distempering etc to the disturbed surfaces to match the exisiting complete all as specified and directed.

Taking down carefully unserviceable distribution board of any capacity including wooden board with making good the disturbed surfaces of walls, etc including two coats of white/colour washing/ distempering etc to match the existing complete all as specified and directed.

Supply & fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amps rated copper bus bar and IP-43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempring etc to match the existing disturbed surfaces and taking down MCB's DB's complete all as specified and directed.

Supply & fixing MCB, SP, AC, 240 volts "B" series capacity of 06 to 40 Amps, 10 kA and making connections complete all as specified and directed.

Supply & fixing isolator/MCB, DP (Double Pole), AC, 240 volts "B" series capacity of 32 to 40 Amps, 10 kA and making connections complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No 03 of SSR part-I connecting to main switch board/ Main DB's including exacavtion, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm centre to centre both way with suitable lifting handle and pit/ chamber in PCC 1:3:6 type C1, Angle iron 40x40x5mm frame for pit cover including testing on completion, complete all as specified and directed.

Supply and fixing fan ceiling complete with electronic type regulator and accessories 230V, 1200mm sweep, BEE 5 Star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and installation of solar water heating system, flat plate collector type with heat exchanger of 100 ltr per day capacity with 2 KW electrical heating backup complete all as specified and directed. Make - V-Guard/Inter Solar system/Racold/Tata Power Solar.

Supply and laying hot water pipes galvanised including insulation of pipe, medium grade supplied and laid complete including fittings 15mm dia (1/2") complete all as specified and directed.

S&F for framed bracket of angles cut to shapes for making stand and ladder cut to shpae drilled and counter sunk for screw including bending and welding angles as necessary (angle size 40x40x5mm reverting confirming to Fe 410-W) (Brackets over 10 Kg each to be measured under structure steel) complete all as specified and directed.

S&F single pole and neutral enclosure with a two pin and earth plug socket complete withone single pole MCB 20 Amps, 240 V complete all as specified and directed.

M&L for rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 750 Ltrs complete all as specified and directed.

S&F MCCB 4 pole, 100 Amps 25kA complete all as specified and directed.

S&F vertical loadline sheet metal enclosure double door, triple pole and neutral (TP&N vertical loadline) AC, 415 volts, 04 way, with 200 Amps rated copper bus bar and IP - 43 & IK 09 protection, with provision of 25kA 100 Amp GI frame MCCB. Make - Legrand/Schneider/ABB with the inbuilt provision for fixing of 1 No MCCB and 12 Nos MCB's inside of DB, with metal door and flush to wall including grouting and cutting in existing wall and making good disturbed surface with two coats of white/colour washing/distempering etc to match the existing one complete all as specified and directed. Make - C&S, Cat ref - CSDBMCCB100DD04IP43S or of equivalent make as approved by GE.

S&F exhaust fan with louver and fxing accessories 230 Volts and 200mm sweep complete all as specified and directed.

All as per item No 163.00 above but 300mm sweep complete all as specified and directed.

S&F water heater storage type, electric capacity 25 Ltrs BEE 5 Star rated complete all as specified and directed. Make - Havells, Cat ref - GHWAMGTWH025, Make - Usha, model Misty digital, Make - Racold/Venus.

Manglam Engineers and Construction Co

vibha associates

Shikhar ji Enterprises

Arun Construction Co.