Augmentation of Water Supply and Connected Services at Port Blair

Amount

Demolition of Reinforced Cement Concrete [reinforcement cut as required to facilitate demolition] in ground floors and Pavings exceeding 15cm thick [below or above ground level] and removing rubbish to a distance not exceeding 1.50 KM and Separating, scraping and cleaning of reinforcement complete all as specified and as directed.

Demolition of Reinforced Cement Concrete [reinforcement cut as required to facilitate demolition] of any description and in any position not otherwise specifically provided for and removing rubbish to a distance not exceeding 1.50 KM and Separating, scraping and cleaning of reinforcement complete all as specified and as directed.

Demolition of Reinforced Cement Concrete as in Roof, Floors [other than ground floor], beams, staircase, landing, Chajjas and similar suspended work including reinforcement cut as required to facilitate demolition and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

Taking up / down Cast Iron Pipes / Water Mains of 300 to 400 mm dia [including all fittings] with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and as directed.

Taking up / down Cast Iron Pipes / Water Mains of 200 / 150 mm dia [including all fittings] with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and as directed.

Taking up / down Cast Iron Pipes / Water Mains of 100 / 80mm dia [including all fittings] with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and as directed.

Taking out Sluice Valves of 300mm dia, of any description complete all as specified and as directed.

Taking out Sluice Valves of 200mm dia, of any description complete all as specified and as directed.

Taking out Sluice Valves of 150mm dia, of any description complete all as specified and as directed.

Dismantling Posts or Struts [Wood, Steel or RCC] of any section, embedded in natural ground including taking out embedded portion and making good disturbed surfaces complete all as specified and as directed.

Surface dressing not exceeding 15 cm deep and getting out in Hard / Dense soil complete all as specified and as directed.

Excavation over areas not exceeding 1.50 m in depth and getting out in Soft / Loose soil complete all as specified and as directed.

Excavation over areas exceeding 1.50 m and not exceeding 3.00 m in depth and getting out in Soft / Loose soil complete all as specified and as directed.

Excavation over areas exceeding 3.00 m and not exceeding 4.50 m in depth and getting out in Soft / Loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and depth not exceeding 1.5m and getting out in Hard / Dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and depth not exceeding 1.5m and getting out in Soft / Loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

Removal of excavated material [Soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M & L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for RCC M–30 Design Mix, using 20mm graded stone aggregate as in foundations including Pile Caps, Rafts, Footings, Foundation Beams, Plinth Beams, Bases for Columns etc. complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc. complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span etc. complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Chajjas and the like complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Walls, Retaining Walls, Abutments, Basement Walls, Ballast Walls and the like, any thickness above top of footings including attached pilasters and buttresses etc complete all as specified.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Slabs supported on walls, beams, columns, landings, shelves, Chajjas and the like complete all as specified and as directed.

Use and removal of Steel Formwork to Sides of concrete Foundations, Pile Caps, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits [if any] of Foundation and Plinth Beams and similar work, Vertical or to Batter for Rough Finished surfaces complete all as specified and as directed.

Use and removal of Steel Formwork to Sides of Pillars, Posts, Struts, Piers, Columns and Stanchions of any Shape / Cross Section for Fair Finished surfaces of concrete complete all as specified and as directed.

Use and removal of Steel Formwork to Sides and Soffits of Floor or Roof Beams, Beam Haunchings, Girders, Bressummers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc, Splays between Floors and Beams and similar works for Fair Finished surfaces of concrete complete all as specified and as directed.

Use and removal of Steel Formwork to Chullah Hoods, Chajjas, Troughs and similar items including Edges and similar works for Fair Finished surfaces of concrete complete all as specified and as directed.

Use and removal of Steel Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and similar work not exceeding 200mm thick [Horizontal or Sloping] for Fair Finished surfaces complete all as specified and directed.

M & L for Use and Removal of Steel Formwork [Plain / Curved] to Faces of Walls, Retaining Walls, Abutments, Parapets and Staircase Railings and similar work including attached Pilasters, Buttresses, etc. Vertical or to Batter for ROUGH finished surfaces of concrete complete all as specified.

M & L for Use and Removal of Steel Formwork [Plain / Curved] to Faces of Walls, Retaining Walls, Abutments, Parapets and Staircase Railings and similar work including attached Pilasters, Buttresses, etc. Vertical or to Batter for FAIR finished surfaces of concrete complete all as specified.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M & L for Providing Precast Cement Concrete Solid Block Masonry with Solid Blocks exceeding 100mm width of 1:3:6, Type C1, using 20mm graded stone aggregate exceeding 100mm width with plain or interlocking joints set in Cement Mortar 1:6 complete all as specified and as directed.

M & L for Providing Precast Cement Concrete Solid Block Masonry with Solid Blocks or Slabs not exceeding 100mm width of PCC 1:3:6, Type – C1 using 20mm graded stone aggregate with plain or interlocking joints as directed set in Cement Mortar 1:4 complete all as specified and as directed.

M & L for rendering on fair faces of brick / concrete surfaces, 10 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5mm thick in cement mortar 1:4 over a backing coat of 10mm thick in CM 1:6 on concrete or brick masonry surfaces including mixing water proofing compound as per manufacturer's instructions and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for rendering on fair faces of brick / concrete surfaces, 15 mm thick in Cement Mortar 1:3, surfaces finished even and smooth without using extra cement including mixing water proofing compound as per manufacturer's instructions complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for rendering on fair faces of brick / concrete surfaces, 10 mm thick in Cement Mortar 1:4, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Supply only Integral Water Proofing Compound complete all as specified and as directed.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparing newly plastered wall surfaces and applying two coats of Acrylic Washable Distemper over a coat of alkali resistant primer complete all as specified and as directed.

M & L for preparing newly plastered / concrete Wall / Ceiling surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] over a Coat of Weather Proof Exterior Primer of same manufacturer as that of paint on Wall / Ceiling surfaces complete all as specified and as directed.

S & F for pre-painted Galvalume steel sheets of Trapezoidal profile having pitch 190mm, depth 29mm or Tiled Profile or Sinusoidal Profile and thickness 0.50mm [Galvalume base-PPGL trapezoidal profile sheets], having tensile strength of 550 Mpa, fixed with aluminium self tapping screws, neoprene and EPDM washers of suitable size in roof covering complete all as specified and as directed. Note: Overlap shall be provided as specified by the manufacturer.

S & F for pre-painted Galvalume steel Plain Sheets and thickness 0.50mm [Galvalume base-PPGL Sheets], having tensile strength of 550 Mpa, in ridges, hips, valley gutters, drip and straight flashing cut to length & bent to shape, girth sheets fixed with aluminium self tapping screws of size 50/75mm and neoprene and EPDM washers of suitable size in roof covering / cladding / eves trim / rake trim and closure trim / valley rain water gutter / down spouts and top rafters etc. complete all as specified and as directed.

S & F Mild Steel work as in Tubular Trusses, Posts etc. including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS - 1161, Grade YST - 240, Medium Grade of any dia complete all as specified and as directed.

S & F MS machine made screw bolts with hexagonal or square head one end and screwed other or screwed both ends, fitted with washers and one hexagonal or square nut exceeding 10 cm long and not exceeding 15 cm long, dia of neck exceeding 11 mm but not exceeding 15 mm complete all as specified and as directed.

M & L for two coats of synthetic enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces not exceeding 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for hardcore of gauge not exceeding 63 mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface in broken boulder complete all as specified and as directed.

M & L for 100 mm thick, PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for 50 mm thick PCC 1:2:4, Type B-1, using 20mm graded aggregate as in Hardstanding / Flooring, surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L for Glass dividing strip 3.0 mm thick, 38 mm wide and insert in position to confirm to design complete all as specified and as directed.

M & L for 150 mm thick PCC 1:2:4, Type B-1, using 20mm graded aggregate as in Plinth Protection, surface finished even and smooth without using extra cement complete all as specified and as directed.

S & F Steel rolling shutters, thickness of laths of 1.25 mm, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, Gear Operated Type with bevel gear box and crank handle, complete all as specified and as directed.

M & L for Powder Coated Aluminium Sections [Minimum 50 Micron thick] of approved colour as in Door, Window, Ventilator Frames, Partitions with one or more rebates and Door, Window, Ventilator Shutters, Sliding or Openable Type, with or without Sash Bar, Aluminium section weighing 0.55 KG / RM including necessary Joining Cleats, Glazing Clips, Neoprene Rubber Packing, Powder Coated Aluminium Snap Beading, Screws, Powder Coated Aluminium Fittings such as Locking Arrangement [1 No], Suitable Handle [1 No], Stainless Steel Friction Hinges [1 No] per Window Shutter and 150mm Dia Handles on both sides, Tower bolts, 200 mm Long [2 Nos], Double Action Floor Spring Hydraulically Regulated made of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty etc. per Door Shutter complete all as specified and as directed. Note: [a] The size of aluminium sections shall be all as specified in relevant IS code and MES Schedule Part - I. [b] Supply only panel inserts of Glass / Particleboard / Gauze / Grills will be measured and paid separately. [c] Unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing, fittings such as Handles, Butt hinges, Tower Bolts, Stainless Steel Friction Hinges and fixing only of panel inserts of Glass / Particleboard / Gauze / Grills etc.

Supply only 5mm thick sheet glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S & F Stainless Steel Railing made with Stainless Steel Pipes of wall thickness not less than 1.6mm, of Grade AISI 316, standard quality, bright polish finish, using 50mm dia pipes for hand rail, 25mm dia pipes for vertical supports / balusters and 25mm dia pipes as in tie bars in three layers, SS tubes shall be welded at the turnings and junctions, welded portions shall be completely grinded and brought to bright and smooth finish including all bends, elbows, making holes in the floor / steps, grouting with epoxy to achieve full strength of railing complete all as specified and as directed.

S & F Rolled Mild Steel work confirming to Fe 410-W, Grade-E- 250, Quality-A as in Plates [plain & chequered], Channels, Angles, square cut or notched [ordinary or counter sunk] forming holes without any attachment complete all as specified and as directed.

S & F Rolled Mild Steel work conforming to Fe 410-W, Grade-E- 250, Quality-A, as in Joist, Channel, Angle, or Tee Sections, fixed independently, without connecting plates etc [cut to ordinary lengths i.e. within 20mm of the length indicated] complete all as specified and as directed.

S & F Mild Steel work confirming to Fe - 290, Grade E-165 as in Hand Rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for Balusters Running Bars, for Doors, Balusters, Nosing to Steps including embeding in concrete and screwing etc, Wind Ties for roof including securing bolts, Posts and Struts in Fencing including cutting tops to shape as directed, bending to shape, notching for wire, drilling holes or as in flat iron fillets [for securing wire mesh and barbed wire etc] including all necessary drilling, bolting or riveting, etc and similar work complete all as specified and directed.

M & L for 150 mm dia RCC Pipes, Class NP 2, laid and jointed with collars laid in trenches and jointed complete all as specified and as directed.

Supplying and laying 100 mm bore Cast Iron Pressure Pipes, Centrifugally Cast, Heavy Duty, Class "B" with Spigot and Socket ends conforming to IS - 1536 in standard lengths suitable for Push-On Rubber Gasket Jointing laid in trenches or fixed to walls / columns complete all as specified and as directed.

S & F 100 mm bore Cast Iron Vent Cowl including jointing with Push-On Rubber Gasket Jointing complete all as specified and as directed.

Supplying and laying 150 mm bore Cast Iron Pressure Pipes, Centrifugally Cast, Heavy Duty, Class "B" with Spigot and Socket ends conforming to IS - 1536 in standard lengths suitable for Push-On Rubber Gasket Jointing laid in trenches or fixed to walls / columns complete all as specified and as directed.

Supplying, fixing and testing of cast iron, heavy duty, specials of any size, radius and length conforming to IS – 1538, Part – I to XXIII: 1976 such as bends [any type, radius and angle], tapers any type [straight, bend, increasing, decreasing or double socket etc], sockets, tail pieces, connecting pieces, tee pieces, single branch, "Y" junction, double branch, cross, [all sockets or socket and spigot], collars, caps and plugs, adopters etc suitable for CI spigot and socket pressure pipes complete all as specified and as directed.

Supply and install Water Level Indicator complete, with Float [PVC], Heavy Duty of suitable size connected to one end of approved quality flexible nylon rope 13mm dia and indicator dead weight type, MS steel needle to the other end of the rope for smooth movement, including suitable size of pulley fixed on angle iron bracket mounted on wall / top of the tank / sump and drilling hole for passing rope of level indicator into the tank from the top of the level indicator board, preparation of plastered surface of wall and applying two coats of synthetic enamel paint back ground and marking of indicator scale for depth in feet and quantity of water in Kilo Litres complete all as specified and as directed.

S & F 1.00mm thick Plain, galvanised, mild steel sheeting, as in construction joint of water tank of 200mm wide with grade of Zinc coating 275 complete all as specified and as directed.

M & L for PCC 1:3:6, Type C-1 [using 20 mm graded granite stone aggregate] in surface channels and drains including forming fair finished drain or channel of any inner girth using extra cement including forms, moulds, mitred / stooped ends complete all as specified and as directed.

M & L for Cutting existing 200mm bore DI / CI Water Mains for drawing 200mm bore DI / CI branch by inserting 200 X 200 X 200 mm DI / CI Tee, including necessary DI / CI Specials, jointing, excavation and earth work, dewatering etc. complete all specified and as directed.

M & L for Cutting existing 300mm bore DI / CI Water Mains for drawing 300mm bore DI / CI branch by inserting 300 X 300 X 300 mm DI / CI Tee, including necessary DI / CI Specials, jointing, excavation and earth work, dewatering etc. complete all specified and as directed.

Supplying and laying 300 mm bore Ductile Iron Pressure Pipes, Centrifugally Cast [Spun], Class "K-9" with Spigot and Socket ends conforming to IS - 8329 in standard lengths suitable for Push-On Rubber Gasket Jointing with inside Cement Mortar Lining and Black Bitumen external coating complete all as specified and as directed. Note: Earth work and excavation will be measured and paid separately.

Supplying and laying 250 mm bore Ductile Iron Pressure Pipes, Centrifugally Cast [Spun], Class "K-9" with Spigot and Socket ends conforming to IS - 8329 in standard lengths suitable for Push-On Rubber Gasket Jointing with inside Cement Mortar Lining and Black Bitumen external coating complete all as specified and as directed. Note: Earth work and excavation will be measured and paid separately.

Supplying and laying 200 mm bore Ductile Iron Pressure Pipes, Centrifugally Cast [Spun], Class "K-9" with Spigot and Socket ends conforming to IS - 8329 in standard lengths suitable for Push-On Rubber Gasket Jointing with inside Cement Mortar Lining and Black Bitumen external coating complete all as specified and as directed. Note: Earth work and excavation will be measured and paid separately.

Supplying and laying 150 mm bore Ductile Iron Pressure Pipes, Centrifugally Cast [Spun], Class "K-9" with Spigot and Socket ends conforming to IS - 8329 in standard lengths suitable for Push-On Rubber Gasket Jointing with inside Cement Mortar Lining and Black Bitumen external coating complete all as specified and as directed. Note: Earth work and excavation will be measured and paid separately.

Supplying and laying MS ERW Pipe, 200 mm bore, Medium Grade , conforming to IS – 3589 including all fittings as in connections from Pump to delivery pipeline or laid in floors or fixed to walls and ceilings including running welding all the joints and testing complete all as specified and as directed.

S & F Cast Iron Non Return Valve with bypass arrangement with suitable flanges, suitable for 250 mm bore pipes confirming to IS – 5312, Class PN –1.6, including necessary nuts, bolts, washers, rubber gasket etc for jointing including complete all as specified and as directed.

S & F Sluice Valve, Cast Iron body, Stainless Steel Spindle, Gun Metal Rings including Wheel for operation, Flanged and Drilled, 250 mm Dia, confirming to IS – 14846, Class PN –1.6, Non Rising Type, Long Body type including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer complete all as specified and as directed.

S & F Sluice Valve, Cast Iron body, Stainless Steel Spindle, Gun Metal Rings including Wheel for operation, Flanged and Drilled, 300 mm Dia, confirming to IS – 14846, Class PN –1.6, Non Rising Type, Long Body type including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer complete all as specified and as directed.

S & F Sluice Valve, Cast Iron body, Stainless Steel Spindle, Gun Metal Rings including Wheel for operation, Flanged and Drilled, 200 mm Dia, confirming to IS – 14846, Class PN –1.6, Non Rising Type, Long Body type including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer complete all as specified and as directed.

S & F Sluice Valve, Cast Iron body, Stainless Steel Spindle, Gun Metal Rings including Wheel for operation, Flanged and Drilled, 150 mm Dia, confirming to IS – 14846, Class PN –1.6, Non Rising Type, Long Body type including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer complete all as specified and as directed.

M & L for Run Lead Joint for DI Pipes of 200 mm dia bore, Spigot and Socket ends complete all as specified and directed Note: DI Fittings & Specials etc. shall be measured and paid separately under relevant items of this BoQ.

M & L for Run Lead Joint for DI Pipes of 250 mm dia bore, Spigot and Socket ends complete all as specified and directed Note: DI Fittings & Specials etc. shall be measured and paid separately under relevant items of this BoQ.

M & L for Run Lead Joint for DI Pipes of 300 mm dia bore, Spigot and Socket ends complete all as specified and directed Note: DI Fittings & Specials etc. shall be measured and paid separately under relevant items of this BoQ.

Supplying, fixing and testing of Ductile Iron, Heavy Duty, Specials confirming to IS – 9523, Class "K-12", PN 10, with inside Cement Mortar Lining and Zinc followed by Black Bitumen external coating, of any size, radius and length such as bends [any type, radius and angle], tapers any type [straight, bend, increasing, decreasing or double socket etc], sockets, tail pieces, connecting pieces, tee pieces, single branch, "Y" junction, double branch, cross, [all sockets or socket and spigot], collars, caps and plugs, adopters etc suitable for DI spigot and socket / Flanged pressure pipes complete al as specified and as directed.

M & L for Construction of Valve Chamber of size 900 X 900 X 900 mm internal size suitable for Sluice Valve, with PCC 1:4:8, Type D2, using 40mm graded aggregate for foundation, 200 mm thick Brickwork with Precast Cement Concrete Solid Block Masonry of 1:3:6, Type C1 using 20mm graded stone aggregate exceeding 100mm width with plain or interlocking joints set in Cement Mortar 1:6, 40 mm thick PCC, 1:2:4, Type B1, using 20mm graded aggregate Coping, rendering in CM 1:4, 15 mm thick including provision of Mild Steel Sheet Cover 3 mm thick with 40 X 40 X 6 mm size Angle Iron frame work embedded in concrete with suitable hinges and locking arrangements including two coat of synthetic enamel black paint over a coat of red oxide zinc chrome primer to steel surfaces and including necessary earth work excavation in any type of soil etc., removal of surplus soil off the premises complete all as specified and shown on drawing.

S & F Foot Valve, Cast Iron Body, 150mm bore with Flanged ends of any pattern with Bypass Arrangement and Confirming to IS – 4038, ISI Marked including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer complete all as specified and as directed.

Supplying, laying and testing XLPE insulated and PVC sheathed, FRLS, armoured heavy duty underground cable, ISI marked with aluminium stranded conductor 1100 Volt grade of size 3½ Core, 50 Sq.mm cross section suitable for earthed system, laying in trenches / duct / fixed to poles / drawn through pipes / sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc. complete all as specified and as directed. Note: The rate quoted deemed to be inclusive of Cable Jointing Kits required for terminations.

Supply and laying of DWC [Double Wall Corrugated] HDPE Pipe and including fittings such as couplers, bends, end caps etc., ISI marked of outer dia of 50mm and inner dia 38mm polyethylene with smooth internal and profiled external surface for non pressure under ground cable complete all as specified.

Supply, lay, test and commissioning of Single Core, 16 Sq.mm, PVC Insulated and PVC sheathed, heavy duty cable, with Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked including crimping type cable lugs, sockets etc. complete all as specified and as directed.

S & F MCCB, FP, 100 Amps, 25 KA, 415 Volts, 50 Hz, suitable for fixing on N3 Frame complete all as specified and as directed.

M & L Earthing complete with Galvanised Steel Earth Plate Electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of Plate not less than 1.50 m below normal ground level connected to 32 X 6mm GI Strip [Earth Lead] and GI pipe 50 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. complete all as specified and as directed.

M & L for Point Wiring complete with 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 drawn through and including heavy duty PVC Conduit, 20 mm dia including all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type and Pressed Metal Flush Box made out of 2mm thick MS Sheet of suitable size and 3 mm thick Hylam Sheet top cover for fixing switches, fittings, regulators etc. concealed in walls, including 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth Dolly for One Light / Fan Point / Bell Point controlled by One Switch complete all as specified and as directed.

All as per Serial Item No. 97 above but One 3 Pin Switch Socket Outlet 5 Amps on Independent Board complete all as specified.

All as per Serial Item No. 97 above but one 3 Pin Switch Socket Outlet 15 Amps on independent board, with 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

S & F Switch Piano, Flush Button, Single Pole, One Way, 5 Amps, 230 Volts complete all as specified and as directed.

S & F Switch Socket Outlet, 3 & 2 Pin, Multipurpose, 5 Amps, 230 Volts, Flush Type complete all as specified and as directed.

S & F Switch Socket Outlet, Multipurpose, 3 pin, 15 Amps and 3 pin, 5 Amps, Flush Type, 230 Volts controlled by One Switch complete all as specified and as directed.

S & F Ceiling Rose, Surface Bakelite, 65 X 50 mm, Three Terminals, 230 Volts complete all as specified and as directed.

S & F Energy efficient, Low Noise, Ceiling Fan, 1200mm Sweep, BEE 5 Star Rated, with BLDC Motor, Copper Wound, 350 RPM, with Double Ball Bearing, Conforming to IS - 373, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50Hz, of approved colour including Down Rod, Canopies, 3 Nos. Blades, Shackles, Safety Rope, Hanging Clamps, Bushes and having P.F >0.94, Service Value >6.5, Air Delivery >215 CMM, Power Consumption less than 35 Watt, THD less than 5% with speed control by Electronic Regulator including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed.

S & F Exhaust Fan, 300mm Sweep, 1400 RPM, Metal Body, Heavy Duty, with Double Ball Bearing, Conforming to IS - 2312, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50 Hz, including Louvers Shutter / Grill, BEE 5 Star Rated and of approved colour including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed.

S & F Surface & wall mounted Energy efficient LED Tube Light Fitting, of not less than 2000 Lumens output, 5700 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Energy efficient & Long life Building Security Light Luminaire, of not less than 3000 Lumens output, 5700 K with Pressure Die Cast Aluminium Housing, IP66 protection, heat resistant glass cover, high power LEDs as light source, electronic driver including GI Bracket made out of 32 mm bore GI Tube, Medium Grade of size not exceeding 1.50 m in length and bent to shape required and fixed with 2 Nos of Pole fitting Clamps made out of MS Flat of size 50 X 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

M & L for Sub main wiring with 2 runs of single core 2.5 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note: 3 runs of 2.5 Sq.mm & one run of 25 mm dia PVC Conduit will be measured as one unit.

M & L for Sub main wiring with 2 runs of single core 4 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note: 3 runs of 4 Sq.mm & one run of 25 mm dia PVC Conduit will be measured as one unit.

S & F MCB DB, SPN, 4 Way, 240 Volts, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs complete all as specified and as directed.

S & F MCB, SP, 6 to 32 Amps, 10 KA, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SPN, 40 to 63 Amps, 10 KA, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F GI water tubing of 15 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, complete all as specified and as directed.

S & F GI water tubing of 20 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, complete all as specified and as directed.

S & F Stop Valves / Angle Cock, 15 mm bore dia of pipe, Fancy type, Chromium Plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions etc. complete all as specified and as directed.

S & F Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and as directed.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Triple Layered, ISI Marked, Cylindrical & Vertical Type 500 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes, Ball Brass Valve, 20 mm dia, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule complete all as specified and as directed.

Hindustan Traders

A.G.Construction

AMR TRADERS

N Rathinam

Prasur Electricals & Engineering Co.

surendra infrastructure pvt ltd

Kakolil Trade Agencies