REPAIR AND REPLACEMENT OF CERTAIN UNSV PARTS OF WOODEN AND STEEL FURNITURE INCLUDING PAINTING AND POLISHING UNDER GE (S) JAIPUR

Amount

Bed Ply top (FD 246/247)

S&F 12mm thick plywood top BWR Grade ISI Mark approved quality in single piece as per drawing without any joint to the bed frame with sutable screw wood / steel with cup washer including removal of damaged ply wood all as specified on drawing or as directed by Engr Incharge.

S&F in repairs to Ist quality hard wood long rail 35mm x 90 mm in section as per existing size of Bed including removal of damaged long rail all as specified on drawing or as directred by Engr Incharge.

S&F in repairs to Ist quality hard wood short rail 35mm x 90 mm in section as per existing size of Bed including removal of damaged short rail all as specified on drawing or as directred by Engr Incharge (each short rail will be measured as single unit)

S&F in repairs to Ist quality hard wood support rail in section as per existing size of Bed including removal of damaged support rail all as specified on drawing or as directred by Engr Incharge (each support rail will be measured as single unit)

S&F in repairs to head board duly finished with teak face ply consisting of 60x30x260mm vertical size and 30x60x400mm horizontal including legs of size 60x60mm in section at top and legnth 400mm from bottom of leg and 30x30mm in section at bottom complete including removal of damaged head board comlete all as specifed on drawing or as directed by Engr Incharge.

S&F in repairs to foot board duly finished with teak face ply consisting of 22x75mm in section hard wood battens 3 nos at eaqual sapce joining top and bottom horizontal rails of foot board. The top and bottom horizontal rails of size 30x60mm shall be Ist quality of hard wood. The vertical legs above horizontal rails shall be 30x60mm complete all as specified on drawing or directed by Engr Incharge

M&L tightening of bed ply top with 'L' Bracket made out of MS Steel as to make functional and stable of bed ply top as specified and directed

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Bed Ply wooden complete all as specified on drawing or as directed by Engr Incharge

Bin Multipurpose (FD/E6/MAP/09) Supply and fix after removing following old and unserviceable Part/ Components of Bin Multipurpose and new parts/ Components of same shape and size, as per existing pattern with glue, bamboo, pins ,screw etc, including tightening of joints. as shown in drawing complete all as specified and directed. Prelaminated particle board shall be 18/19 mm thick, ISI marked, in shade & texture as approved by Engr-Incharge. Exposed sides of the board to be covered with matching PVC lipping. Teak wood shall be well seasoned, free from pits & knots as per standard drawing.Ply wood shall be ISI marked as per standard drawing

Side made out of prelaminated partical board

Shelves made out of prelaminated partical board

Drawers made out of prelaminated partical board and bottom of drawing made out of plywood 6mm

Door made out of prelaminated partical board

Top made out of prelaminated partical board

Bottom frame made out of prelaminated partical board

Knobs/Handles as approved

M&L tightening of bin multipurpose as to make functional and stable as specified and directed

S&F teakwood beading duly polished in colour matching the prelaminated board with french polish for glossy finish

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Bin Multipurpose and as specified and directed by Engr Incharge

Chair dining long back (FD-E6/MAP/10, FD-357, TP)

Removing of unserviceable rear leg of chair dinging long back, tighting of loose components S&F new leg made out of Ist class hard wood duly shaped and fix with other members carefully by means of Fevicol & Bamboos pins as per shown in the drawing

All as per item No 3.01 above but front leg 30mmx40mmx460mm as per drawing

All as per item No 3.01 above but verticle back strip as per drawing

All as per item No 3 .01 above but front/back/side rail 25mmx65mmx450mm as per drawing

All as per item No 3.01 above but stiffeners 20mmx25mmx450mm as per drawing.

All as per item No 3.01 above but replacement of suitable PVC shoe duly fixed with 20mm screw

All as per item No 3.01 above but repalcement of unserviceable cushion sheets and S&F foam cushion of 40 density sheet duly covered with long cloth and tapestry cloth on 12mm ply wood BWR as shown in the drawing. colour of tapestry cloth as approved by GE.

M&L tightening of chair dining long back with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed.

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Chair dining long back and as specified and directed by Engr Incharge.

Chair Writing (FD-280)

Removing of unserviceable rear leg of chair writing, tighting of loose components S&F new leg made out of Ist class hard wood duly shaped and fix with other members carefully by means of Fevicol & Bamboos pins as per shown in the drawing.

All as per item No 4.01 above but front leg as per shown in the drawing.

All as per item No 4.01 above but back rest of chair writing as per shown in the drawing.

All as per item No 4.01 above but stiffener as per shown in the drawing.

All as per item No 4.01 above but rear rail of chair writing as per shown in the drawing.

All as per item No 4.01 above but front rail of chair writing as shown in the drawing.

All as per item No 4.01 above but side rail of chair writing as shown in the drawing.

All as per item No 4.01 above but removing of exiting unserviceable PVC shoe and S&F new PVC shoe with suitable screw.

M&L tightening of chair writiing with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L Re-canning of Chair writing wooden with plastic cane of 1/2 round 2.0mm wide & 0.40mm thick woven border round and back with 4mm side of approved quality (white/cream in colour including removing of old canning compete as as specified and directed

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces

Chair dining (FD-279)

Removing of unserviceable rear leg of chair dining, tighting of loose components S&F new leg made out of Ist class hard wood duly shaped and fix with other members carefully by means of Fevicol & Bamboos pins as per shown in the drawing

All as per item No 5.01above but for front leg as shown in the drawing

All as per item No 5.01 above but for front and back rail as per shown in the drawing

All as per item No 5.01 above but for side rail as per shown in the drawing

All as per item No 5.01 above but for back rest as per shown in the drawing

All as per item No 5.01 above but for stiffener as per shown in the drawing

All as per item No 5.01 above but replacement of PVC shoe duly fixed with suitable screw

M&L tightening of chair dining with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L Re-canning of Chair dining wooden with plastic cane of 1/2 round 2.0mm wide & 0.40mm thick woven border round and back with 4mm side of approved quality (white/cream in colour including removing of old canning compete as specified and directed

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Chair dining as specified and directed

Chair Easy (FD-229)

Removing of following unserviceable part of Chair Easy, tighting of loose components and supply and fixing new part as mentioned in respective following items made out of Ist class hard wood duly shaped as per drawing and fixing with other member by Fevicol and bamboo pins including french polishing to replaced part of wooden to match with existing part to make serviceable complete all as specified and directed

Front leg of chair easy as per drawing

Hand rest of chair easy as per drawing

Rear leg of chair easy as per drawing

Front/back rail of of chair easy as per drawing

Side rail of of chair easy as per drawing

Replacement of PVC shoe duly fixed with suitable screw

M&L tightening of chair easy with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L Re-canning of Chair Easy with plastic cane of 1/2 round 2.0mm wide & 0.40mm thick, woven border round and back with 4mm wide of approved quality (white/cream in colour) including removing of old canning drawing No FD-229

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French poolish on the wooden surfaces of Chair easy wooden. drawing No FD-229

Hat stand with mirror : (FD-233)

Removing of unserviceable hanging hooks of Hat stand and S&F new hanging hooks as per drawing

Replacement of teak ply wood 3/4mm as per drawing and directed by Engineer Incharge

Replacement of commercial ply wood ISI Mark 6mm as per drawing and directed by Engineer Incharge

Replacement of looking mirror 5mm as per drawing

Replacement of Pegs as per drawing and directed

Replacement of Teak wood beading all as per drawing

M&L preparation of wooden surfaces by cleaning scrapping and smoothing of surfaces with sand paper and applying one coat of French poolish on the wooden surfaces of Hat stand with mirror drawing No FD-233

Mirror Dressing (Gents) (FD/E6/MAP/16)

Removing of UNSV mirror and S&F new mirror 5.5mm thick overall size of mirror 600x1200mm backed by 12mm thick BWR grade plywood covered by decorative mould and supported on 50x28mm hard wood frame all around & as per shown in the drawing.

Removal of UNSV back ply and S&F new 12mm thick BWR grade ISI Mark ply wood

Removal of UNSV sides and S&F 18mm thick pre-laminted particle board & shown in the drawing

Removal of UNSV shelves and S&F new shelves 8mm thick glass shelves supported on glass holder

Removal of UNSV hinges and S&F new hinges continious piano hinges to open the mirror frame in horizontal circle.

Removal of UNSV magnet catcher and S&F new magnet catcher 02 Nos each at top

M&L preparation of wooden surfaces by cleaning scrapping and smoothing of surfaces with sand paper and applying one coat of French poolish on the wooden surfaces of Mirror Dressing (Gents) drawing No FD/E6/MAP/16

Peg Table (FD-277/384) Removing of unserviceable part of Peg Table S&F new part made out of 1st class hard wood duly shaped as shown in the drawing and fixing with other member by means of Fevicol and bamboo pins to make serviceable the item of Peg Table of size as per drawing and as directed

All as per item No 9.00 above but for side rail size as shown in the drawing and as directed

All as per item No 9.00 above but for legs size as shown in the drawing and as directed

All as per item No 9.00 above but for stiffners size as shown in the drawing and as directed

All as per item No 9.00 above but for replacement of unserviceable table top with 18mm thick pre-laminated particle board ISI marked with teak wood edging all around.

All as per item No 9.00 above but S&F PVC shoe with suitable screw

M&L tightening of peg table with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Peg table and as specified and directed by Engr-Incharge

Sofa sets 5 seater (3+1+1) (FD-373/FD/MAP-II/02)

Taking down unserviceable leg of sofa set and S&F new leg made of Ist class hard wood duly size and fixed in position as shown in drawing.

All as per item No 10.01 replacement of unserviceable front long rail of sofa set (3 seater) and S&F new front long rail of Ist class hard wood all as specified and shown in drawing.

All as per item No 10.01 replacement of unserviceable front rail of sofa set (single seater) and S&F new front long rail of Ist class hard wood all as specified and shown in drawing.

All as per item No 10.01 replacement of unserviceable rear long rail of sofa set (3 seater) and S&F new rear long rail of Ist class hard wood all as specified and shown in drawing.

All as per item No 10.01 replacement of unserviceable rear rail of sofa set (single seater) and S&F new rear long rail of Ist class hard wood all as specified and shown in drawing.

All as per item No 10.01 above but for replacement unserciveable side rail and S&F new side rail as specified and shown in drawing

All as per item No 10.01 above but replacement unserviceable hand rest and S&F new hand rest as specified and shown in drawing.

All as per item No 10.01 above but replacement unserviceable wooden strips of seat & back and S&F new wooden strips as specified and shown in drawing

M&L tightening of sofa set 5 seater (3+1+1) with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Sofa set 5 seater and as specified and directed by Engr-Incharge

Sofa sets 4 seater (FD-281/373)

Taking down unserviceable leg of sofa set 4 seater (single seater x 4) and S&F new leg made of Ist class hard wood duly size and fixed in position as shown in drawing.

All as per item No 11.01 replacement of unserviceable front rail of sofa set (single seater x 4) and S&F new front long rail of Ist class hard wood all as specified and shown in drawing.

All as per item No 11.01 replacement of unserviceable rear rail of sofa set (single seater x 4) and S&F new rear long rail of Ist class hard wood all as specified and shown in drawing.

All as per item No 11.01 above but for replacement unserciveable side rail and S&F new side rail as specified and shown in drawing

All as per item No 11.01 above but replacement unserviceable handrest and S&F new handrest as specified and shown in drawing

All as per item No 11.01 above but replacement unserviceable wooden strips of seat & back and S&F new wooden strips as specified and shown in drawing

M&L tightening of sofa set 4 seater (single seater x 4) with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Sofa set 4 seater and as specified and directed by Engr-Incharge.

Side board (FD-372/341)

Removing of unserviceable top of side board and S&F new top of pre-laminated baord 18mm thick, Teak face, ISI marked as shown in the drawing duly polished on biding.

All as per item No 12.01 above but bottom of side board as shown in the drawing

All as per item No 12.01 above but replacement of unserviceable back of side board

All as per item No 12.01 above but for replacement of Shutter of the side board and supply and fix new shutter with both side pre laminated particle board 18mm thick ISI marked fixed with piano type hinges continuous 20mm.

All as per item No 12.01 above but for replacement of Knobs of chromium plated of approved coloured and standard quality.

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Side board and as specified and directed by Engr Incharge

Table bed side (FD-276)

M&L Replacement of unserviceable top and S&F new top of table bed side made out of 18mm pre-laminated particle board ISI marked with 4mm teak wood edging as per drawing.

All as per item No 13.01 above but replacement of unserviceable both side of table bed side of 18mm pre-laminated particle board ISI marked with 4mm teak wood edging as per drawing.

All as per item No 13.01 above but replacement of unserviceable shelf of table bed side of 12mm pre-laminated particle board ISI marked with 4mm teak wood edging as per drawing.

All as per item No 13.01 above but replacement of unserviceable back side of table bed side of 6mm ply wood with 4mm teak wood edging as per drawing.

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Side board and as specified and directed by Engr Incharge.

Table Dressing Ladies/Gents/Ladies (MAP) (FD-251, 379, FD/E6/MAP/16)

Removing of existing Unserviceable mirror with ply and both side long rail fitted with the bottom shelf of table dressing ladies and S&F new mirror 5.5mm thick of clear vision with 6mm thick ply fixed at back and both side long rail fitted with the bottom shelf duly polished. (FD-251)

Removing of unserviceable complete bottom shelf (incl legs) of Table dressing ladies and S&F new complete bottom shelf (incl legs made of Ist class hard wood) of pre laminated particle board 18mm thick, Teak face, ISI marked as shown in the drawing (FD-251)

Removing of unserviceable Knobs and S&F new Knobs of chromium plated of approved coloured and standard quality. (FD 251, 379, FD/E6/MAP/16)

Repalcement of unserviceable cushion sheets of table dressing ladies stool and S&F new foam cushion of 40 density sheet duly covered with long tapestry cloth on 12mm ply wood BWR as shown in the drawing. colour as approved by GE (FD/E6/MAP/16)

Replacement of swivel type nylon castors and S&F new swivel type nylon castors all as per drawing and as directed. (FD/E6/MAP/16)

Removing existing Unserviceable mirror with ply and wooden frame from table dressing gents and S&F new mirror 5.5 mm thick of clear vision with 6mm ply on back and wooden frame (FD-379).

Removal of unserviceable shelf of table dressing Gents and S&F new shelf with knobs duly polished. All complete as per drawing and directed (FD-379)

M&L preparation of wooden surfaces by cleaning scrapping and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table Dressing Ladies/Gents/Ladies (MAP) and as specified and directed by Engr-Incharge

Table 3' x 2' with / without drawer (FD-283, 284)

Removing of unserviceable leg of Table 3' x 2' with / without drawer, tighting of loose components and S&F new leg made out of 1st class hard wood duly shaped as shown in the drawing and fixing with other member by means of Fevicol and bamboo pins to make serviceable all as specified and directed by Engr-Incharge.

All as per item No 15.01 above but for replacement of Table top of size 3’x2’ with 18mm thick pre-laminated particle board ISI marked with teak wood edging around.

All as per item No 15.01 above but for repalcement of long rail shown as per drawing

All as per item No 15.01 above but for replacement of short rail shown as per drawing

All as per item No 15.01 above but for repalcement of Middle stiffeners of size 915mm x 40mm x 25mm.

All as per item No 15.01 above but for replacement of Side stiffeners of size 600mm x 40mm x 25mm.

All as per item No 15.01 above but for repalcement of Bottom ply of drawers (commercial ply woods of size 550mm x 310mm x 6mm).

All as per item No 15.01 above but for replacememt of side members of drawer as shown in the drawing

All as per item No 15.01 above but for repalcement of ‘L’ type bracket of hard wood 75mm x 75mm x 20mm in table to support rail and leg fixed with screws.

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table 3'x'2 with/without drawer and as specified and directed by Engr-Incharge

Table dining 6 pers (FD-239, 273, 376 & FD/E6/MAP-II/03)

Removing of unserviceable leg of table dining 6 pers S&F new leg made out of 1st class hard wood duly shaped as shown in the drawing and fixing with other member by means of Fevicol and bamboo pins to make serviceable all as specified and directed by Engr-Incharge.

All as per item No 16.01 above but for replacement of long rail of size 1500mm x 100mm x 25mm.

All as per item No 16.01 above but for replacement of short rail of size 900mm x 100mm x 25mm.

All as per item No 16.01 above but for replacement of Hard wood ‘L’ type bracket made out of hard wood 100mm x 100mm x 25mm fixed with screws

All as per item No 16.01 above but for replacement of unserviceable table top with 18mm thick pre-laminated particle board ISI marked with teak wood edging all around.

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table dining 6 pers and as specified and directed by Engr-Incharge

Table dining 4'x3' (FD/E6/MAP/09)

Removing of unserviceable leg of table dining 4'x3' S&F new leg made out of 1st class hard wood duly shaped as shown in the drawing and fixing with other member by means of Fevicol and bamboo pins to make serviceable all as specified and directed by Engr-Incharge.

All as per item No 17.01 above but for replacement of long rail of size 1200mm x 100mm x 25mm.

All as per item No 17.01 above but for replacement of short rail of size 900mm x 100mm x 25mm.

All as per item No 17.01 4bove but for repalcement of Hard wood ‘L’ type bracket made out of hard wood 100mm x 100mm x 25mm fixed with screws

All as per item No 17.01 above but for replacement of unserviceable table top with 18mm thick pre-laminated particle board ISI marked with teak wood edging all around.

All as per item No 17.01 above but S&F PVC shoe with suitable screw.

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table dining 4'x3' and as specified and directed by Engr-Incharge

Table dining 8 pers

Removing of unserviceable leg of table dining 8 pers S&F new leg made out of 1st class hard wood duly shaped as shown in the drawing and fixing with other member by means of Fevicol and bamboo pins to make serviceable the item of dining table 8 pers leg of size as per drawing and as directed

All as per item No 18.01 above but for replacement of long rail of size 1800mm x 100mm x 25mm

All as per item No 18.01 above but for replacement of short rail of size 900mm x 100mm x 25mm.

All as per item No 18.01 above but for replacement of hard wood ‘L’ type bracket made out of hard wood 100mm x 100mm x 25mm fixed with screws.

All as per item No 18.01 above but for replacement of Table top with 18mm thick pre-laminated particle board ISI marked with teak wood edging all around as shown in the drawing and as directed.

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table dining 8 pers and as specified and directed by Engr-Incharge

Table Writing (FD- 275)

Removing of unserviceable leg of table writing, tighting of loose components S&F new leg made out of 1st class hard wood duly shaped as shown in the drawing and fixing with other member by means of Fevicol and bamboo pins to make serviceable the item of Table writing leg of size as per drawing and as directed

All as per item No 19.01 above but long rail as shown in the drawing as and directed

All as per item No 19.01 above but short rail as shown in the drawing as and directed

All as per item No 19.01 above but for bottom base of box with 18mm thick commercial particle board (ISI marked) as shown in the drawing as and directed

All as per item No 19.01 above but side of box with 18mm thick commercial particle board ISI marked as shown in the drawing as and directed

All as per item No 19.01 above but top with 18mm thick pre-laminated particle board ISI marked with 4mm thick teak wood beading all around as shown in the drawing as and directed.

All as per item No 19.01 above but for back ply box with 6mm thick commercial ply (ISI marked) as shown in the drawing as and directed

All as per item No 19.01 above but for door 18mm pre-laminated particle board of size 380mm x 450mm including knob and hinges piano type scale hinges as specified and directed

All as per item No 19.01 above but for side of drawer hard wood size 450mm x 75mm x 20mm.

All as per item No 19.01 above but for bottom of drawer 6mm thick commercial ply (ISI marked) of size 600mm x 450mm .

All as per item No 19.01 above but for replacement of hard wood ‘L’ type bracket made out of hard wood fixed with screws.

All as per item No 19.01 above but S&F PVC shoe with suitable screw

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table writing and as specified and directed by Engr-Incharge

Table Centre (FD-274, FD/E6/MAP/09)

Removing of unserviceable leg of Table Centre S&F new leg made out of 1st class hard wood duly shaped as shown in the drawing and fixing with other member by means of Fevicol and bamboo pins to make serviceable the item of Table Centre for leg of size as per drawing and as directed

All as per item No 20.01 above but long rail size as shown in the drawing and as directed

All as per item No 20.01 above but short rail size as shown in the drawing and as directed

All as per item No 20.01 above but for replacement of table top made out of 18mm pre-laminated particle board ISI marked with 4mm thick teak wood edging all around as shown in the drawing and as directed.

All as per item No 20.01 above but for hard wood bracket ‘L’ type of size 75mm x 75mm x 20mm fixed with screws.

All as per item No 20.01 above but S&F PVC shoe with suitable screw

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table Centre and as specified and directed by Engr-Incharge

Teapoy wooden (FD-278, 382)

Removing of unserviceable leg of teapoy wooden and S&F new leg made out of 1st class hard wood duly shaped as shown in the drawing and fixing with other member by means of Fevicol and bamboo pins to make serviceable the item of teapoy wooden leg of size 540mm x 60mm x 30mm.

All as per item No 21.01 above but side short rail of size 450mm x 50mm x 20mm

All as per item No 21.01 above but long side rail of size 600mm x 50mm x 20mm

All as per item No 21.01 above but ‘L’ type bracket of hard wood of size 75mm x 75mm x 20mm fixed with screws.

All as per item No 21.01 above but Top of teapoy wooden of size 450mm x 600mm x 18mm thick with one side pre-laminated particle board ISI marked with teak wood beading alround.

All as per item No 21.01 above but replacement of PVC shoe duly fixed with suitable screw

M&L preparation of wooden surfaces by cleaning scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Teapoy wooden and as specified and directed by Engr-Incharge.

TV Trolly (FD/E6/MAP/04)

Replacement of 5.5mm thick plain glass openable glass shutters with magnetic catcher and stainless steel pad fitting for glass. All as per drawing as directed.

All as per item No 22.01 above but replacement of top of TV trolly with 18mm thick pre-laminated particle board ISI marked of approved shade with 50 x 50mm moulded teak wood beading on 3 sides to shape to be provided all as per drawing and as directed.

All as per item No 22.01 above but replacement of swivel type nylon castors all as per drawing and as directed.

All as per item No 22.01 above but replacement of both sides of TV trolly with 18mm thick pre-laminated particle board ISI marked of approved to shape to be provided all as per drawing and as directed.

All as pe item No 22.01 aobve but replacement of decorative handles as per drawing

Almirah Large steel (FD-1031)

Taking out old unserviceable existing handle and S&F new chromium plated handle including necessary nut, bolts, washer etc for almirah large steel.

Taking out existing shelves and making the same in functioning condition including necessary nuts, bolts, clips and washer etc of Almirah large steel all as directed.

Removing existing locking device with MS plate rod and S&F new locking device with plate rod complete in almirah large steel as directed.

Taking out old unserviceable lock of Almirah large steel and S&F lock with six levers locks and hole cover with duplicate keys best quality approved by GE

Taking out old unserviceable leg of almirah large steel and S&F new legs made out of 20 gauge MS sheet made to shape and sizes shown on drawing all as directed.

Taking out of unserviceable door of almirah large steel and S&F new door made out of 1.00mm thick MS Sheet

M&L preparation old painted steel surfaces by cleaning & scapping and applying one coat of synthetic enamel paint olive green/grey/hemotone with spray gun or by manual brush with roller as per requirement in appropriate shade complete all as specified and directed but Almirah large steel with shelves both side (out side and in side)

Almirah steel 1/2 hanging 1/2 shelves (FD/E6/Map/18)

Taking out old unserviceable existing handle and S&F new chromium plated handle including necessary nut, bolts, washer etc for almirah steel 1/2 hanging 1/2 shelves

Taking out existing shelves and making the same in functioning condition including necessary nuts, bolts, clips and washer etc of almirah steel 1/2 hanging 1/2 shelves all as directed.

Removing existing locking device with MS plate rod and S&F new locking device with plate rod complete in almirah steel 1/2 hanging 1/2 shelves as directed.

Taking out old unserviceable lock of almirah steel 1/2 hanging 1/2 shelves and S&F lock with six levers locks and hole cover with duplicate keys. best quality approved by GE

Taking out old unserviceable leg of almirah steel 1/2 hanging 1/2 shelves and S&F new legs made out of 20 gauge MS sheet made to shape and sizes shown on drawing all as directed.

Taking out of unserviceable door of almirah steel 1/2 hanging 1/2 shelves and S&F new door made out of 1.00mm thick MS Sheet

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/grey with spray gun or by manual brush with roller as per requirement in appropriate shade complete all as specified and directed but almirah steel 1/2 hanging 1/2 shelves with shelves both side (out side and in side)

Almirah Medium Steel (FD-1032)

Taking out old unserviceable existing handle and S&F new chromium plated handles including necessary nut, bolts, washer etc for almirah medium steel.

Taking out existing shelves and making the same in functioning condition including necessary nuts, bolts, clips and washer etc of almirah medium steel all as directed.

Removing existing locking device with MS plate rod and S&F new locking device with plate rod complete in almirah medium steel as directed.

Taking out old unserviceable lock of Almirah Medium steel and S&F lock with six levers locks and hole cover with duplicate keys.

Taking out old unserviceable leg of almirah medium/steel and S&F new legs made out of 20 gauge MS sheet made to shape and sizes shown on drawing all as directed.

Taking out of unserviceable door of almirah med steel and S&F new door made out of 1.00mm thick MS Sheet

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/grey with spray gun or by manual brush with roller as per requirement in appropriate shade complete all as specified and directed for Almirah med steel with shelves both side (out side and in side)

Bed Hard Steel (FD/E6/MAP/08)

Removing of existing unserviceable ply wood from bed hard steel and S&F new plywood 12mm thick (Make:- Kitply,Century Ply) BWR Phenol bounded commercial plywood with edging 1950mm x 900mm ISI Mark all as per drawing and directed.

Removing of unserviceable Head rest (with leg and particle board complete) and S&F new Head rest (with leg and particle board 18/19mm complete) as per drawing.

Removing of unserviceable foot rest (with leg and particle board complete) and S&F new foot rest (with leg and particle board 18/19mm complete) as per drawing

Removing Unserviceable old long rails and supply and fix new long rail MS tubular pipe size 1920x 65 x 25mm ISI marked required as per drawing.

Removing Unserviceable old short rails and supply and fix new short rail MS tubular pipe size 1920x 65 x 25mm ISI marked required as per drawing.

Removing Unserviceable middle stiffner and supply and fix new middle stiffner duly ISI marked required as per drawing and directed.

M&L elect welding to Bed Hard Steel where required and filling properly at places of welding point. Elect welding shall be done all round the MS pipe and all welding and filling at one broken point shall be measured as one point ie one unit.

Painting with Synthetic enamel black paint after scrapping of rusted paint complete as per drawing all as specified and directed.

Removing Unserviceable PVC Shoes of Bed Hard Steel and supply and fix new PVC Shoes of Bed Hard Steel required as per drawing and directed.

Book Case steel ((FD-1028, FD 356, FD 69M))

Taking out existing shelves and making the same in functioning condition including necessary nuts, bolts, clips and washer etc of book case steel complete all as specified & directed.

S&F lock with six levers locks and hole cover with duplicate keys including taking out old unserviceable lock complete all as specified & directed.

S&F sliding glass door including taking out of unserviceable sliding glass door of as per drawing all as specified & directed.

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr Incharge.

M&L preparation old painted steel surfaces by cleaning & scraping and applying one coat of synthetic enamel paint olive green/black/grey with spray gun or by manual brush with roller as per requirement (out side and in side) complete all as specified and directed.

Box Kit steel (FD-98(M))

S&F Plain black iron sheet of 22 gauge shall be provided at top, bottom, sides, shelf and stiffeners and for base, angles and corners 16 gauge plain black iron sheet shall be used incl removal of the UNSV parts.

S&F standard PVC recessed handle as shown on drawing.

S&F mild steel hash & staple safety type, stove enameled 100 mm size, one number shall be provided as directed by Engr Incharge.

M&L preparation old painted steel surfaces by cleaning & scapping and applying one coat of synthetic enamel paint olive green/black with spray gun or by manual brush with roller as per requirement (out side and in side) complete all as specified and directed.

Chair CB Steel without Arm (FD-75(M))

Taking out old unserviceable seat frame of chair CB steel without Arm and M&L seat frame 2nd class hard wood duly weaving with white/cream plastic cane 2mm to 2.5mm wide partially rounded off of approved quality and border as specified in drawing including fixing with MS nut and bolt with washer, size of seat frame as per drawing.

All as per Item No 29.01 above but back frame of chair CB steel without arm (size of back frame as per drawing

M&L gas welding to chair CB steel without arm where required and filling properly at places of welding point. Gas welding shall be done all round the conduit pipe and all welding and filling at one broken point shall be measured as one point ie one unit.

Removing of existing unserviceable MS Clit of Chair CB steel and S&F by gas welding of new MS Clit under the sheet as per drawing and directed.

M&L scrapping of surface of chair CBA steel without Arms frame with emery paper making smooth surface and applying one coat of OG synthetic enameled paint all as directed.

M&L removing of existing unservicable PVC shoes of chair CB steel without arm and S&F new PVC Shoes as directed by Engr Incharge.

M&L removing of existing unservicable PVC Plug of Pipe of chair CB steel without arm and S&F new PVC Plug as directed by Engr Incharge.

Chair CB Steel with Arm (FD-75(M))

Taking out old unserviceable seat frame of chair CB steel with Arm and S&F new seat frame with MS nut and bolts with washer, size of seat frame as per drawing.

All as per Item No 30.01 above but back frame of chair CB steel with arms.

M&L gas welding to chair CB steel with arm where required and filling properly at places of welding point. Gas welding shall be done all round the conduit pipe and all welding and filling at one broken point shall be measured as one point ie one unit.

M&L removing of existing unservicable arm rest of chair CB steel with arm and S&F new arms rest made with IInd class hard wood as per drawing and duly black clolour synthetic enamel painted as per drawing and directed.

Removing of existing unserviceable MS clit of Chair CB steel and S&F by gas welding of new MS clit under the sheet as per drawing and directed.

M&L scrapping of surface of chair CB steel with Arm frame with emery paper making smooth surface and applying one coat of OG synthetic enameled paint all as directed.

M&L removing of existing unservicable PVC shoes of chair CB steel with arm and S&F new PVC Shoes as directed by Engr Incharge.

M&L removing of existing unservicable PVC Plug of Pipe of chair CB steel with arm and S&F new PVC Plug as directed by Engr Incharge.

Chair Writing steel (FD/E6/MAP/12)

S&F seat and back 12mm, teak ply with poly urethane foam 50mm thick moulded with density 40 with Raxine of approved colour and shade including taking out old unserviceable seat and back complete all as specified & directed. .

Replacement leg as specified in the drawing and as directed by Engr Incharge.

Replacement of arm rest as specified in the drawing and as directed by Engr Incharge.

M&L dry cleaning of existing seat and back of chair writing steel with arm as directed by Engr Incharge.

Painting with black paint after scrapping of rusted paint complete by spray gun as per drawing all as specified and directed.

Chair School with Hand Board (FD/E6/MAP/05)

S&F PVC seat with back of chair school with hand board with suitable nut & bolt and washer as per drawing and directed, including taking out old unserviceable seat and back of chair school with hand board all as specified & directed. .

S&F Hand Board of chair school with hand board with suitable nut & bolt and washer as per drawing and directed, including taking out old unserviceable Hand Board of chair school with hand board. Hand board will be made out of prelaminated particle board 18mm thick ISI Mark, size as per drawing and directed.

S&F Wire mesh of chair school with hand board with Gas welding as per drawing and directed, including taking out old unserviceable wire mesh of chair school with hand board all as specified & directed. .

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr-Incharge.

S&F front/rear legs of chair school with hand board with Gas welding as per drawing and directed, including taking out old unserviceable front/rear legs of chair school with hand board all as specified & directed. .

Painting with black paint after scrapping of rusted paint complete by spray gun as per drawing all as specified and directed.

Chair Verandah PVC Steel (MAP) (FD/MAP/II/06)

M&L gas welding to chair verandah where required and filling properly at places of welding point. Gas welding shall be done all round the conduit pipe and all welding and filling at one broken point shall be measured as one point ie one unit.

M&L hard rubber shoe in legs of chair including removal of broken rubber shoe.

M&L scrapping of surface of chair verandah frame with emery paper making smooth surface and applying one coat of white synthetic enameled paint all as directed.

Removing of old unserviceble side leg with arm frame and S&F new side leg with arm frame made 20mm MS cunduit pipe as per drawing fixing with gas welding.

Removing of old unserviceable seat combined frame and S&F new PVC seat frame made 20mm MS cunduit pipe as per drawing and fixing with gas welding.

Removing of old unserviceable back combined frame and S&F new PVC back frame made 20mm MS cunduit pipe as per drawing and fixing with gas welding.

Removing of old unservieable front leg stiffener and S&F new front leg stiffener made with 12mm round plain MS Bar as per drawing and fixing with gas welding.

Chair Computer (FD/E6/MAP/01)

M&L for removing unserviceable seat and back and S&F new seat & back alongwith the fabric & PVC lipping wherever applicable & replacing the same with new 12mm thick hot pressed phywood upholstered with fabric & moulded polyurethane foam. The back foam shall be designed with contour lumber support with PVC lipping all around. The cushions shall be of 40 density 75mm thick for seat & 50mm thick for back alongwith the fabric of approved quality & colour. All as directed by Engr Incharge.

M& L for removing unserviceable caster wheel and S&F new castor wheels of Chair Computer/Chair Revolving adjustable(Best quality)

M&L for removing unserviceable hand rest of Chair Computer/Chair Revolving adjustable and S&F new handrest of the chairs with new hand rest matching the previous all in shape, size, material & quality.

M&L for removing unserviceable and S&F pedestal assembly of revolving chairs with new complete pedestal assembly all matching the sape, size & quality of the existing.

M&L for removing unserviceable hydraulic assembly and S&F new hydraulic assembly & making the seat adjustment functional all as directed by Engr Incharge.

M&L dry cleaning of existing seat and back of chair Computer /Chair Revolving as directed by Engr Incharge.

Foam with back steel (FD-78(M))

Taking out old unserviceable planks seat & back and S&F new planks seat and back Hard wood first class (in single piece) with the help of MS nut and bolt with washer, size of planks as per drawing.

M&L legs made of square MS pipe 25mm, 1.6mm wall thickness fixing neatly all as directed including taking out old unserviceable leg complete all as specified & directed.

Supplying and fixing centre stiffeners of long rail made out of 25mm x 25mm square MS pipe of 1.6mm wall thickness as shown on drawing including taking out old unserviceable existing centre stiffeners of long rail complete all as specified & directed.

M&L spot welding by gas welding through out in broken joints of frame all as specified & directed.

Painting of Foam with back steel with olive green / black after scrapping of rusted paint complete by spray gun as per drawing all as specified and directed.

M&L for removing unserviceable PVC shoe and S&F PVC rubber shoe black color.

Foam with out back (FD-1027)

Taking out old unserviceable planks and S&F new planks hard wood first class (in single piece) with the help of MS nut and bolt with washer, size of planks as per drawing.

M&L legs made of square MS pipe 25mm, 1.6mm wall thickness fixing neatly all as directed including taking out old unserviceable leg complete all as specified & directed.

supplying and fixing centre stiffeners of long rail made out of 25mm x 25mm square MS pipe of 1.6mm wall thickness as shown on drawing including taking out old unserviceable existing centre stiffener of long rail complete all as specified & directed.

M&L spot welding by gas welding throughout in broken joints of frame all as specified & directed.

Painting of Foam with out back steel with olive green / black after scrapping of rusted paint complete by spray gun as per drawing all as specified and directed.

M&L for removing unserviceable shoe and S&F PVC rubber shoe black color.

Locker steel (FD-1029)

Taking out existing shelves and making in position including necessary elect welding of bed side locker steel as directed by Engr Incharge.

Replacement of old Unserviceable SS handles with new handle including necessary nuts and bolts washer etc for bed side locker steel(Best Quality).

Replacement of old Unserviceable legs of bed side locker by new legs made out of 18 guage MS sheet made to shape and sizes shown on drawing all as directed by Engr Incharge.

Taking out of unserviceable door of Bed side locker steel and S&F new door made out of 1.00mm thick MS Sheet.

M&L preparation old painted steel surfaces by cleaning & scrapping and applying one coat of synthetic enamel paint olive green/black/grey with spray gun or by manual brush with roller as per requirement in appropriate shade complete all as specified and directed for Bed side locker steel with shelves both side (out side and in side).

Shoe Rack steel (FD/E6/MAP/02/R)

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr Incharge.

M&L for painting the frame of the Shoe Rack steel with two coats of synthetic enamel black paint over a coat of primer with the help of spray gun after smoothning the surface with electric ginder complete all as specified & directed.

M&L for removing unserviceable and S&F PVC shoes to the legs as applicable complete all as specified & directed.

S&F Wire mesh of Shoe Rack Steel as per drawing and directed, including taking out old unserviceable wire mesh of Shoe rack all as specified & directed. .

Table Computer (FD/E6/MAP/03)

M&L for removing unserviceable prelaminated top and S&F with new top of 18mm thick prelaminated particle board ISI marked and exposed sides of the board to be covered with matching PVC strip as per drawing

M&L for removing unserviceable prelaminated sides and S&F with new side of 18mm thick prelaminated particle board both side laminated of ISI marked and exposed sides of the board to be covered with matching PVC strip as per drawing.

M&L for removing unserviceable prelaminated particle board pullout tray and S&F with new tray of 18mm thick prelaminated both side laminated of ISI marked and exposed sides of the board to be covered with matching PVC strip.

M&L for removing userviceable prelaminated particle board bottom shelf and S&F with new shelf of 18mm thick prelaminated board both side laminated of ISI marked & pattern as approved by Engr Incharge. Exposed sides of the board to be covered with matching PVC lipping.

M&L for removing unserviceable and S&F drawer channels with new telescopic channels(replace in pair) with smooth run.

M&L for painting to all the steel surfaces with spray gun in black color after scrapping off the surface with electric grinder. Make- ASIAN paints/DULUX/ BERGER.

M&L for romoving unserviceable knobs for drawer and S&F with new decorative knobs as approved by Engr Incharge.

M&L for removing unserviceable PVC shoe and S&F new PVC shoes to the legs as applicable complete all as specified & directed.

Table Bed Side Steel (FD/E6/MAP/15)

M&L for removing unserviceable back and S&F new back of 18mm thick prelaminated board one side teak face & one side white as approved by Engr Incharge ISI marked. Exposed sides of the board to be covered with matching PVC lipping.

M&L for removing unserviceable side and S&F with new side of 18mm thick prelaminated particle board both side teak face ISI marked as approved by Engr Incharge.

M&L for removing unserviceabletop drawer and S&F with new drawer of 18mm thick prelaminated particle board one side teak face & one side white ISI marked as approved by Engr-Incharge. Exposed sides of the board to be covered with matching PVC lipping.

M&L for removing unserviceable top and S&F with new top of 18mm thick prelaminated particle board one side teak face & one side white ISI marked as approved by Engr Incharge.

M&L for removing unserviceable bottom drawer and S&F with new drawer of 18mm thick prelaminated particle board one side teak face & one side white irrespective of what is shown on drawing ISI marked exterior grade as approved by Engr Incharge. Exposed sides of the board to be covered with matching PVC liping.

M&L for removing unserviceable knobs for drawer and S&F with new decorative knobs as approved by Engr Incharge.

M&L for removing unserviceable shoe and S&F new PVC rubber shoe black color.

M&L for removing unserviceable drawer channels and S&F with new telescopic channels (replace in pair) with smooth run.

Removing of unserviceable MS frame of Table Bed side steel and S&F of new MS tubular pipe frame as per drawing fixing with elect welding/screw as reqd.

M&L preparation old painted steel surfaces by cleaning scrapping and applying one coat of synthetic enamel paint black with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed by Engr Incharge.

Table office officer/clk (FD-1004, FD-1003)

Taking out old unserviceable lock of drawers of table office officer/ clerk steel and S&F lock with four levers locks with duplicate keys.

Taking out existing drawers of table office clerk /officers steel and re-fixing same after necessary setting of drawers for free movement all as directed.

Replacement of Top of table office officers steel with 18 mm thick prelaminated particle board ISI mark with teak wood beadings.

Replacement of Top of table office clk steel with 18 mm thick prelaminated particle board ISI mark with teak wood beadings.

Taking out of unserviceable door shutter of Table office officer steel and S&F new door shutter made out of 1.00mm thick MS Sheet and as per drawing

Taking out old unserviceable leg of table office officer/clk steel and M&L legs made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

Taking out old unserviceable front & back long rail of table office officer/clk steel and M&L front & back rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

Taking out old unserviceable side rail of table office officer/clk steel and M&L side rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr Incharge

M&L preparation old painted steel surfaces by cleaning Scrapping and applying one coat of synthetic enamel paint olive green/grey with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed

M&L for removing unserviceable shoe and S&F new PVC rubber shoe black color.

Table 3' x 3' steel (FD-1009)

Replacement of Top of table 3'x3' steel with 18 mm thick prelaminated particle board ISI mark with teak wood beadings.

Taking out old unserviceable leg of table 3'x3' steel and M&L legs made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

Taking out old unserviceable front & back rail of table 3' x3' steel and M&L front/back rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

Taking out old unserviceable side rail of table 3'x3' steel and M&L side rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr Incharge.

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/black/grey with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed.

M&L for removing unserviceable shoe and S&F new PVC rubber shoe black color.

Table 3'x2' without drawer steel (FD-1007)

Replacement of Top of table 3'x2' without drawer steel with 18 mm thick prelaminated particle board ISI mark with teak wood beadings.

Taking out old unserviceable leg of table 3'x2' without drawer steel and M&L legs made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

Taking out old unserviceable front & back rail of table 3' x2' without drawer steel and M&L front / back rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

Taking out old unserviceable side rail of table 3'x2' without drawer steel and M&L side rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr Incharge.

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/black/grey with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed.

M&L for removing unserviceable shoe and S&F new PVC rubber shoe black color.

Table 3'x2' With drawer steel (FD-1008)

Replacement of Top of table 3'x2' with drawer steel with 18 mm thick prelaminated particle board ISI mark with teak wood beadings.

Taking out old unserviceable leg of table 3'x2' steel with drawer and M&L legs made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

Taking out old unserviceable front & back rail of table 3' x2' with drawer steel and M&L front / back rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

Taking out old unserviceable side rail of table 3'x2' with drawer steel and M&L side rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drawing.

Taking out old unserviceable lock of drawers of table 3'x2' with drawer steel and S&F lock with four levers locks with duplicate keys.

Taking out existing drawers of table 3'x2' with drawer steel and re-fixing same after necessary setting of drawers for movement and as per drawing and directed .

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr Incharge.

M&L preparation old painted steel surfaces by cleaning & scraping and applying one coat of synthetic enamel paint olive green/black/grey with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed.

M&L for removing unserviceable shoe and S&F new PVC rubber shoe black color.

Table dining OR (FD-165)

Taking out unserviceable top of table dining OR and S&F new Top of table shall be of size 72” x 24” excluding beading using 18mm thick prelaminated particle board ISI Mark with teak wood beadings.

Taking out old unserviceable leg of table dining OR and M&L legs made of square MS pipe 25mm, 1.6mm wall thickness fixing neatly all as directed.

Taking out old unserviceable existing centre stiffeners/long rail of table dining OR and supplying and fixing new one made out of 25mm x 25mm square MS pipe of 1.6mm wall thickness as shown on drawing and directed.

Taking out old unserviceable side stiffener, short rail of table dining OR supply and fixing new one made of 25mm square conduit MS, 1.6mm wall thickness as shown on drawing and directed.

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr Incharge.

M&L preparation old painted steel surfaces by cleaning & scraping and applying one coat of synthetic enamel paint olive green/black/grey with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed.

M&L for removing unserviceable shoe and S&F new PVC rubber shoe black color.

Teapoy Verandah (FD-255)

S&F Top made out of 18/19mm pre-laminated particle board ISI marked incl teak wood beading around as per drawing and directed

Removing of old unserviceble leg and S&F new leg made out of 20mm MS cunduct pipe as per drawing fixing with gas welding

M&L spot welding by gas welding throughout in broken joints of frame of teapoy verandah complete all as specified & directed.

Painting of Teapoy Verandah with white paint after scrapping of rusted paint complete by spray gun as per drawing all as specified and directed

M&L for removing unserviceable shoe and S&F new PVC rubber shoe black color.

Teapoy Verandah steel (FD/E6/MAP/17)

S&F Top made out of 18mm pre-laminated particle board ISI marked incl teak wood beading around as per drawing and directed

Removing of old unserviceble leg and S&F new leg made out of 20mm MS cunduct pipe as per drawing fixing with gas welding.

M&L spot welding by gas welding throughout in broken joints of frame of teapoy verandah steel complete all as specified & directed .

Removing of old unserviceble base tray frame and S&F new base tray frame made out of 5mm MS bar as per drawing fixing with gas welding

Painting of Teapoy Verandah steel with black paint after scrapping of rusted paint complete by spray gun as per drawing all as specified and directed

M&L for removing unserviceable shoe and S&F new PVC rubber shoe black color.

M/s M S CONSTRUCTION (BID ID -3223024)

C.P.Computers (BID ID -3228234)

MISHON TRADING CORPORATION (BID ID -3223646)

M/S United Builders (BID ID -3223100)

AJAY TRADERS (BID ID -3222564)