COMPREHENSIVE B/R MAINT WORK, REPAIRS TO ROOF TREATMENT, PLASTERING AND MISC B/R WORKS IN THE AREA-II OF AGE B/R-III UNDER GE (W) JABALPUR

Amount

Taking down cement plaster / terrazzo of any description thickness including raking out joints hacking for key scrubbing down with water complete all as specified and as directed.

M&L for 10mm thick rendering on brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering on concrete/brick surfaces in CM 1:4 with water proofing compound as per manufactures instruction finished even and smooth without using extra cement complete all as specified and as directed. . (Note:- WPC shall be measured and paid separately)

M&L for 5mm thick rendering on Concrete Surfaces in Cement Mortar 1:3 as in ceiling surfaces finished Even and Smooth, without using extra cement complete all as specified and as directed.

M&L for applying three coats of white wash on newly plastered surfacces of ceiling including preparation complete all as specified and as directed.

M&L for applying two Coats of oil emulsion distemper over 3 mm thick wall care putty over a coat of chalk whitening primer on newly Plastered Surfaces of internal wall including preparation complete all as specified and as directed.

M&L for applying Two Coats of Cement Base Paint over a coat of alkali resistant primer on newly Plastered Surfaces of external Walls including preparation complete all as specified and as directed.

Demolition of cement concrete in ground floor and pavings not exc 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 25MM thick PCC Type B-1 1:2:4 (Using 20mm graded stone aggregate ) to receive rough finish as in floor complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed.

Dismantling floor hearth or wall tiling/china moisac including cement mortar bedding (but not backing ) , removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or rectangular) area of Each tile exc 0.18 Sqm but not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15mm thick screed bed in cement mortar 1:6 for laying floor finishes complete all as specified and as directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or rectangular) area of Each tile exc 0.18 Sqm but not exceeding 0.36 Sqm, as in skirting ,dados in vertical surfaces etc and including 10mm thick cement plaster 1:4 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 450 x 300 x 6 to 7 mm,450x350 or 350x250 6 to 7mm thick on vertical surface such as skirting/dado etc. ,set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile with & including 10 mm thick cement plaster in cement mortar 1:4 finished rough to fix the tiles complete all as specified and as directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick square/ rectangular area of Each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match, laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Material and labour for 20- 25 mm thick machine cut kota stone flooring laid and jointed with neat cement slurry mixed with pigment to match the shade of the slab laid over and including 20 mm thick screed bed in cement mortar 1:6 including rubbing and polishing complete all as specified and as directed.

M&L for 18 to 20 mm thick machine cut kota stone as in vertical surfaces risers of steps , skirting, dado and pillars etc set and jointed in neat cement slurry and pointed with grey cement mixed with pigment to match the colour of stone slab laid over and including 10 mm thick rendering in cement mortar 1:4 including rubbing and mirror polishing complete all as specified and as directed.

Demolition of brick or stone/boulder masonry built in cement mortar including all aquoins, arches, pillars etc but excluding ashlar facings complete all as specified and as directed.

M&L for Brick work with sub class ‘B’ brick, old size straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Taking down chowkhats or frames with shutter (without taking off shutter from the frame) area not exc 1.5 Sqm Each complete all as specified and as directed.

S&F for PVC door frame size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinf with MS square tube in opening as per specificationn complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails . M,S frame shall be covered with heat moulded plain colour PVC ,C, channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails , lock rails and bottom rails on either side and as gap insert for top rail and bottom rail Panelling of plain colour PVC sheet to be fitted in the M.S frame welded /sealed to the stiles & rails with suitable PVC sheet beading , and jointed together with solvent cement , supplying and fising in the frame at site as per specification and drawing complete all as specified and as directed.

S&F for Aluminium anodised sections for doors/windows/ventilators with one or more rebates including joining cleat for fixing etc complete with frames, shutters and grills of size directed by Engineer-in-charge including handles, tower bolts, grills etc complete all as specified and as directed. Note:- Floor door spring, sheet glass, wire cloth, lock, etc shall be measured and paid seperately.

S& F for 4mm thick aluminium Partion Panel sheets for doors complete all as specified and as directed.

S&F for mild steel framed work such as guard bars/grills,grating etc with end of bars shouldered and/or riveted or forged into spikes and similar works including one shop coat of zinc chrome primer complete all as specified and as directed.

S&F, for 150mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F, for 300mm long aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F, for 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin,Type-B-21 complete all as specified and as directed.

S&F for 125mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F for 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel spring complete all as specified and as directed.

S&F for door closer hydraulically regulated designation No-2 universal type of aluminium body fixed to door frames with screws or by welding complete for door shutters of 850 to 1000mm in width complete all as specified and as directed.

S&F for 3mm thick Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in Each pane complete all as specified and as directed.

S&F for 4mm thick figured glass, pinn headed type and glazing with oil putty in square n. exc 0.5 Sqm Each pane complete all as specified and as directed.

S&F for 5.5mm thick Sheet glass,ordinary quality and glazing with oil putty in square exc 0.5 sq. m in Each pane complete all as specified and as directed.

S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets including E- Grid frame work complete all as specified and as directed.

S&F for suspended prepainted false ceiling, self design, self texture, using E grid exposed suspended system, grid section size 600mm x 600mm comprising of GI powder coated main runner of dimensions 39mm x 24mmx 08mm thick (thickness comprising of GI /0.4+PPPCGS/0.3mm & weight of runner 1.35 Kg for 3600mm length) cross tee of dimensions 29mm x 24mm 0.8mm thick and thick wall angle 22.2 mm x 22.2mmx 0.65mm thick (thickness comprising of GI /0.35+PPPCGS/0.3mm & weight of angle 0.70 Kg for 3050mm lenght) with and including 4mm thick HPSC (high pressure steam cured) pre-primed, self embossed, texture designer board, water resistant termitant, fire resistant for insulation and acoustic purpose to be placed in the grid systemduly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips (wt - 0.007 Kg/clip) hold down clips (wt-0.0035 Kg/clip) with provn of light fixture complete all as specified and as directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets as in roof coverings complete all as specified and as directed.

M&L for Pre-painted galvatume aluminium zinc coating GI based corrugatged steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L for Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Dismantling timber fillets,posts rafter purlin under 40 sqcm in sectional area as in framed work complete all as specified and as directed.

Dismantling timber in scantling 40 Sqcm and over in section as in framed work in any position complete all as specified and as directed.

Dismantling wroght iron or mild steel work of any description not otherwise provide for complete all as specified and as directed.

S&F for hand rails, half rounded or other stock section or core for wooden hand rail straight portion, drilled and counter sunk for balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc; flat iron fillets (for securing wire mesh etc,) including all necessary drilling bolting or riveting, etc and similar work conforming to Fe410-0 or Fe 310-0 complete all as specified and as directed.

S&F for mild steel screw bolt (machine made) with square or hexagonal head at one end, screwed other, fitted with washer and one hexagonal or square n exc 5cm, long and 5 to 10mm dia complete all as specified and as directed.

S&F for rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to a common rafters, fixed with angle cleats or other connecting plates of Gde fe 410-0 or fe 250-0 complete all as specified and as directed.

M&L for applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer on newly steel surfaces of any description n exc 10 cm width or girth including preparation complete all as specified and as directed.

M&L for applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer on newly steel surfaces of any description exc 10 cm width or girth including preparation complete all as specified and as directed.

M&L for applying one coat of synthetic enamel paint on old painted steel surfacces of of any description, n exc 10 cm width or girth including preparation complete all as specified and as directed.

M&L for applying one coat of synthetic enamel paint on old painted wooden surfacces of any description, n exc 10 cm width or girth including preparation complete all as specified and as directed.

Roughening surfaces of old concrete floor/terrace by picking incl. taking down existing detoriated / decayed tar felt PCC tiles or any type of treatment including loose surface, scraping with scraper, chiseling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 50 m. complete all as specified and as directed.

M&L for wire brushing and cleaning top surface of tiles,lime terracing or cement concrete,including flashing and junction of parapet,etc,and surface painting with a layer of blown bitumen of any penetration applied hot @1.70 kg per Sqm.blinded with grit or pea size gravel @ 0.006 cu.m per Sqm and lightly tampered (area of flashing etc.shall be added to the roof area complete all as specified and as directed.

M&L for 10 mm thick screed bed or bedding layer on concrete roof surface in CM 1:3 with water proofing compound @ 3 % by weight of cement finished fair and even to maintain the proper slope of roof surface etc complete all as specified and as directed.

M&L for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following for roofs-

(a) Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement plaster complete all as specified and directed.

(b) One coat of hot blown bitumen of grade 85/25 @ 1.2kg /Sqm shall be applied over primed surfaces complete all as specified and as directed.

(c) One layer of APP based polymeric water proofing membrane of weight not less than 3 kg/Sqm consisting 3mm thick reinforced with polyster non wove fabric shall be unrolled surfaces with lap of 100 mm and the over lap shall be sealed by flame complete all as specified and directed. .

(d) Applying two coats of aluminum paint on top of membrane @ 0.10Kg/Sqm complete all as specified and directed. .

M&L for 20mm thick Screed bed or bedding layer in cement mortar 1:4 on roof complete all as specified and directed.

S&F for cement concrete tiles of size 25cmx25cmx22mm thick machine cut pressed set jointed and pointed in neat cement slurry with grey cement and pigments in floors and cut and polished complete all as specified and as directed.

M & L Bitumastic gola, with 80/25 bitumen and coarse sand mixture, 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces complete all as specified and as directed.

M & L for Cutting grooves in brick wall of size 75mm wide and 65mm deep , and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) in lintels upto 1.5 clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers ,apex stones, bed plates, water troughs and the like including use of formwork (straight or curved) ,including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed. (Note: reinforcement where provided shall be measured and paid separately)

M&L for 60 mm thick machine pressed precast concrete interlocking paver block and shape and size confirming to IS 15658-2006 of M-35 Grade with grey cement and pigment complete all as specified and directed.

M&L for Chequered cement concrete tiles 20 cm x20 cm x25 mm thick, set, jointed and pointed with grey cement and pigment to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M & L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M & L for 100 mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base, sub floor of flooring, paving, path etc surfaces finished even and fair to receive top layer complete all as specified and as directed.

S & F for 5mm thick Solid PVC wall lining consisiting of wood grain prnted PVC Sheet inclusive of solvent cement and fuixing at site on PVC frame as per specifications and drawing complete all as specified and as directed.

S & F for 5mm thick PVC sheet fillet of width 35mm thick paneling inclusive of fixing on to wall to make pvc frame as per specifications and drawing complete all as specified and as directed.

S&F in repair 18 mm thick PVC sheet one side prelaminated of approved texture as in Kitchen cabinet. (withshelves and partitions) including necessary fitting & fixture as per manucture's instructions complete all as specified and as directed.

S&F for 150mm long Handles of senso (as per 3D designs) including all connection fitting complete all as specified and as directed.

S&F for continuos (piano) hinges,mild steel bright finish or electrogalvanised,width of flaps 30 mm complete all as specified and as directed.

M/S A K MUKHERJEE (BID ID -3100829)

RP ANAND (BID ID -3098359)

chandan construction (BID ID -3100075)

HAFEEZ CONSTRUCTION (BID ID -3099826)

charanjeet singh (BID ID -3100804)

SHRI KRISHNA CONSTRUCTIONS (BID ID -3100311)