SPECIAL REPAIRS TO BUILDING NO P-76 (G AND F GP) 800 MT STORAGE SHEDS OF 311 COY ASC (SUP) TYPE-B UNDER GE MISAMARI

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Taking down cement plaster on brick, concrete block wall or stone walls, etc., including raking out joints,hacking for key,scrubbing down with water etc compleate all as specified and directed.

Material and labour 3mm thick, 38mm wide glass dividing strips inserted in position to conform to design complete all as specified and directed.

Material and labour for 100 mm thick PCC 1:2:4 type B2( using 40 mm graded stone aggregate) as in floor in alternate bays complete all as specified and directed.

Material and labour for 15 mm thick rendering in cement mortar (1:6) on brick or concrete wall surfaces finished even & smooth without using extra cement compleate all as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer including 1 mm thick average wall care putty etc complete all as specified and directed Make :-Snowcem/Asian guttu/Duracem/Acrocem/Ecocem/Rubicem (J&N) or equivelent.

Material and labour for complete removal of existing treatment of old wall and applying two coats of oil bound distemper over a coat of primer over and including 1 mm thick wall care putty, complete all as specified and directed.

Material and labour for 15 mm thick rendering in cement mortar (1:4) on brick or concrete wall surfaces finished even & smooth without using extra cement compleate all as specified and directed.

Material and labour for rough cast plaster as specified in SSR part-I clause 14.22, over and including 10 mm thick plaster in cement mortar (1:3), on brick mansonry wall surfaces compleate all as specified and directed.

Material and labour for 15 mm thick rendering in CM (1:4 ) on brick or concrete surface finished even and smooth without using extra cement with water proofing compound @3% by weight of cement as per manufactures instruction on internal wall surfaces of manholes/septic tanks etc. (Note: WPC shall be measured and paid separately under relevant item of Schedule 'A')

Supply only integral water proofing compound. Make :- Waterseal/Pidilite/Cico/Bostic/Fosrock/J K Cement or equivalent ISI Marked

Material and labour for applying two coats of acrylic emulsion paint over a coat of alkali resistant primer on new plastered surfaces including preparation of new wall surface complete all as specified and directed.

Material and labour for complete removal of existing treatment of wall and applying two coats of exterior emulsion paint over a coat of alkali resistant primer on old plastered surfaces including preparation of old plaster of wall surface complete all as specified and directed.

Material and labour for PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in channel, etc in manhole including necesarry form work (if required) complete all as specified and directed.

Extra for forming fair finishing drain or channels 30 cm inner girth in cement concrete using extra cement including forms, moulds stopped ends etc complete all as specified and directed.

Material and labour for 75mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in path/plinth protection/hard standing including finished surface finished even and smooth without using extra cement complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) area not exceeding 1.50 sqm each including iron mongeries complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Supply and fix steel ventilator with top hung shutters including projecting type hinges with steel handle, and steel peg stay complete with glazing bars dovetailed or welded (Comply with IS:1038-1983 as specified in SSR part -I 10.25),complete all as specified and directed.

Supply and fix 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5 Sq.m in each pane including oil putty and bedding complete fitting complete all as specified and directed. Make :- Saint Gobin/Modi float/Triveni float glass/hindustan pilkington or equivalent ISI Marked

Hacking out old broken glass (any thickness, size quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

Supply and fix framed work as in doors or gates of angle with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering Door, etc to be prepared for hanging with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete conforming to Fe 410-W (Gde-E-250) complete all as specified and directed.

Supply and fix framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

Supply and fix Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates of grade Fe-410 W (gde-E-250) Quality -A complete all as specified and directed.

Supply and fix Mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes Fe-410 W (gde-E-250) Quality -A complete all as specified and directed.

Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide primer to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of new steel surfaces complete all as specified and directed. Make:- Berger Luxol HI Gloss/Borolac (J&N) /Nerolac/Asian paints Apcolite/Superlac (Shalimar)/Dulux or equivalent.

Material and labour for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed. Make:- Berger Luxol HI Gloss/Borolac (J&N) /Nerolac/Asian paints Apcolite/Superlac (Shalimar)/Dulux or equivalent.

Material and labour for 75mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in sub base floorings complete all as specified and directed.

Material and labour Machine pressed precast concrete interlocking paver block any shape and 60mm thickness, jointed and pointed with grey cement and no pigment in floor/footpath including 25 mm thick sand cushion vibrated with machanical vibrator as per IS 15656-2006 M-35 grade complete all as specified and directed..

Demolition of stone/boulder masonry , built in cement mortar including all quoins,arches,pillars etc ,but excluding ashlar facings dressed stone work and precast concrete articles completed all as specified and directed .

Material and labour for brick work with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 completed all as specified and directed .

All as per Item No. 31 herein before but (Except brick i.e. Serviceable old brick obtained from Item no 31 herein before), straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 completed all as specified and directed .

Material and labour for plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate ) as in roof padding, coping, benching, roof kerbs or mud stops, rounded or chamfered on edges and similar etc finished even and fair complete including necessary form work all as specified and directed.

Dismantling of Asbestos cement (corrugated ted, semi corrugated, etc.)/galvalume/fibre glass/CGI sheets in roof coverings complete all as specified and directed.

Material and labour pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of shade / colour as approved by Engineer-in-Charge having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. Make : Tata/Sail/Jindal/Dynaro of (Spectrum).

Material and labour pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of shade/colour as approves by Engineer-in-Charge having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. complete all as specified and directed. Make : Tata/Sail/Jindal/Dynaro of (Spectrum).

Supply and fix 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof wall etc complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed.

Material and labour for 1.25 mm thick Mild steel sheet eaves gutters, galvanised class 3, half round exc 150 mm dia with rounded edges complete all as specified and directed.

Supply and fix PVC (SWR) pipes single socketed 110 mm dia in any length with rubber ring joints fixed to walls, clamps/hook for holding of pipe etc complete all as specified and directed. Make :- Supreme/Kisan/Tirupati/Finolex/Prince.

Supply and fix PVC (SWR) bends 110 mm bore of any radius with access door complete all as specified and directed. Make :- Supreme/Kisan/Tirupati/Finolex/Prince.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforced cut as required to facilitate demolition) complete all as specified and directed.

Material and labour for lean concrete PCC 1:3:6 type D-2 using 40mm graded aggregates as in foundation filling mass concrete complete all as specified and directed.

Supply and fix for steel tubular Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc.conforming to IS-1161-1998 grade St-240. A complete all as specified and directed.

Supply and fix Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

Supply and fix Mild steel TMT bars 6-8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete, all as specified and directed.

Material and labour for reinforced cement concrete (nominal mix) 1:1½ :3 type A1 using 20 mm graded stone aggregate in columns & similar works complete all as specified & directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

Material and labour for providing pre-cast RCC (1:2:4) type 'B-1' using (20 mm graded crush stone aggregate) as in cover slabs of manholes and similar location including necessary form work and set in cement mortar (1:4) complete all as specified and directed.

Use and waste of form work to sides of concrete sides of columns, pillers, piers, post and struts, slab supported on walls etc for fair finished surface complete all as specified and directed.

Supply and fix for Tubo Ventilators Industrial/domestic turbo ventilator as in Manufactureres Insturction :- (i) (Turbine Dia 28 Inch (760mm), (Nech/Throat-24"), (Height-18"/610mm) (Vanes(Blades) - 42 Vanes, Aluminium 0.50mm Alloy 8011), Base Ring MOC(Mounting ring - Stainless steel),(Top plate MOC- Stainless steel 0.80 mm thickness). (ii) Rotation - Twin sealed 6203ZZ bearing with self lubricating duponty zytel 101L Polyamide 66 resin to ensure frictionless rotation even at lowest wind velocity Twin sealed 6201ZZ bearings with self lubricating Duponty Zytel 101L Polyamide 66 resin to ensure frictionless rotation even at lowest wind velocity. (iii) (Centre shaft : 18mm high carbon steel zinc plated) ( Inner Arms - M.S. with electro zinc plating), (Outer Arms - M.S. with electro zinc plating), (Frp base plate - 2mm thick clear 1.020 mtr wide 1.65 mtr long matching your sheet profile weight 8Kg Approx), (Centre width - 800mm+/-5mm), (Dia of Bottom Ring- 600mm+/-15mm), (Nos of Bearings -02 Nos), (Bearing Type : skf-6001ZZ & 6003ZZ) (Rivets-Aluminium Alloy wiht Washer) Make:- Tubro Ventilator India (Industrial Ventilating Solutions) or Equivalent.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder,ceiling roses, regulators, switch socket outlet, bulk head fittings, tube light fittings etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Taking down carefully by unscrewing from board/outlet boxes, fittings and fixture such as main switches & DBs of any size and any capacity and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Taking down sub main wiring/service cable of any type and any size and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Taking down UG cable of any type and any size and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Material and Labour for Point wiring with 1.50 sq mm (nominal area), two single core PVC insulated unsheathed , 1100 volts grade, multi-stranded copper conductor FRSL Grade, in and including PVC casing capping and its accessories of suitable size,high grade ISI marked in walls/roof and MS pressed steel terminal boxes of 1.22mm thick of suitable size duly painted with red oxide metal primer including fixing/grouting sunken/ as per site requirement including provision of 3 mm thick Bakelite hylem sheet for mounting the switches/sockets/regulators including PVC insulated unsheathed single core multi-stranded copper conductor FRSL Grade cable of size 1.5 sq mm green in colour as earth continuity conductor connected to common earth dolly for one light/fan point controlled by one way switch complete all as specified and directed.

All as per item No 55 here-in-before but for one ceiling fan/Exhaust fan point controled by one switch on the same board complete all as specified and directed

All as per item No 55 here-in-before but for one 5 Amp socket outlet three pin controled by one switch on the same board complete all as specified and directed

All as per item No 55 here-in-before but for one 5 Amp socket outlet three pin controled by one switch on independent board complete all as specified and directed

All as per item No 55 here-in-before but for 3 pin 15 Amps socket outlet independant board drawn from DB and including PVC insulated multi stranded copper conductor 2.5 sqmm 1100 volts grade and earth continuity wire 1.5 sqmm PVC insulated copper wire (Green) including PVC casing and capping complete all as specified and directed..

Supply and fix switch piano flush type single pole one way 5 Amp 240 volts complete all as specified and directed

Supply and fix socket outlet 2 in 1 , 3 pin 5 Amps flush type 240 volts complete all as specified and directed .

Supply and fix switch socket combination multipurpose 2/3 pin , 5 Amps flush type 240 volts complete all as specified and directed .

Supply and fix switch socket combination multipurpose 3/5 Pin 5/15 Amps flush, 240 volts complete all as specified and directed.

Supply and fix ceiling rose surface bakelite 65 x 50 mm two to three terminals AC 230 volts complete all as specified and directed.

Supply and fix ceiling fan regulator step type, flush type heavy duty suitable to work on 230 volts AC supply complete all as specified and directed.

Supply and fix lamp holder, insulated body, with back plate for 10 Watt LED lamp Cat Part No LHLDERHEMD8X010 MAKE HAVELLS complete all as specified and directed.

Supply and fix sheet metal enclosures for DBs (Double door type) when MCB TPN 4 way with 200 Amps rated bus bar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection complete all as specified and directed.

Supply and fix sheet metal enclosures for DBs (Double door type) when MCBs to be used 240 volts 8 way with 200 Amps rated bus bar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection complete all as specified and directed.

Supply and fix MCB four pole 40/63 Amp 415 volts, confirm to IS /IEC 60898 breaking capacity of 10 KA, complete all as specified and directed. Make :- L&T cat No BB40630C or equivalent Havells/Bajaj/Crompton

Supply and fix MCB Double pole 32 Amp 240/415 volts, confirm to IS /IEC 60898 breaking capacity of 10 KA, C-curve complete all as specified and directed. Make :- L&T cat No BB20320C or equivalent of Havells/Legrand

Supply and fix MCB SP 6-32 Amp 240 volts,50 HZ , confirm to IS /IEC 60898 breaking capacity of 10 KA, C-curve complete all as specified and directed. Make :- L&T cat No BB10320C or equivalent Havells/Bajaj/Crompton

Supply and fix wall mounted LED 18 watts, box type (decorative) light fitting, 230 volt with extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver connector block etc with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from celling rose to fitting including LED tube 4' x 18 watts complete all as directed by Engineer-in-Charge. Make :- Havells, Cat part No LHLDCLXEUL83018, LHFYBPNIA1W022 or equivalent in Bajaj & Crompton.

Supply and fix energy saving new generation environmental friendly long life versatile pressure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 form ceiling rose of fitting with and including GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtre long bend to required shape complete al as directed by Engineer-in Charge. Make - Havells, Cat Part No LHETBXU7PA6S025 or equivalent in Bajaj & Crompton

Supply and fix sub main wiring alongwith earth wire1100 volts grade double core PVC insulated and unsheathed cable with stranded copper conductor 2 core 6 Sqmm FRLS grade on surface or recessed or drawn in PVC casing capping along with 4.00 Sqmm single core copper conductor multi stranded cable as earth continuity conductor complete all as specified and as directed. (Note: One run of PVC casing capping ,one run of 4 sqmm earth wire and 2 Run of 6 sqmm cable shall be measured as one run.)

Taking down ceiling fan of any sweep, keeping with safe custody and hanging/fixed in repair the same with replacement of UNSV PVC insulated PVC sheathed 3 corte multistandard copper conductor cable of size 23/0.193 from ceiling rose to fan terminal conductor complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for foundation and getting out in soft/loose soil complete all as specified and directed.

Returning,filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm thick, in hard/dense soil complete all as specified and directed.

Removal of surplus soil of distance not exceeding 50 Metre and depositing where directed at a level not exceeding 1.5 Metre above the starting point complete all as specified and directed..

Supply and spread fine dry river sand for cable cushioning in trenches complete all as specified and directed. (Note:- Sand shall be measured and paid puneshed thickness)

Supplying and laying well brunt brick,locally available best quality (Sub class 'B' bricks) laid in trenches perpendicular to UG cable protections complete all as specified and directed

Supplying, testing,commissioning and laying LT UG Cable of size 4 Core 16 Sqmm laid in trences/floor/on wall/service connection PVC insulated, sheathing and armd 1100 volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed

Supply and fix GI tubing 40 mm dia ' Light grade', in trench or on wall for the protection of UG cable complete all as specified and directed. Make :- Jindal/TATA/Prakash Surya/Swastik/Appolo/BST/Kalinga/Goodluck or equivelent.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron. Earth strip protected by GI pipe 15 mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as directed by Engineer In Charge.

KIRTEE KAMAL TAMULI

M/S Vandana Enterprises

M/S SHARMA CONSTRUCTION