PETTY REPAIR FOR ATTENDING DAY TO DAY EM EXTERNAL WATER SUPPLY COMPLAINTS AT RANGPURI AND REPAIR MAINT OF FIRE FIGHTING MISC WORKS AND ELECTRICAL COMPLAINTS FOR PUMP HOUSE FIRE FIGHTING PANEL AND CONNECTED AREA IN THE AREA OF AGE U WATER SUPPLY NO I

Labour only for attending day to day external water supply complaints of all nature i.e leakage in water supply pipe lines, fitting/fixture, over flow of overhead tank, no water supply,taking out water from trenches during repair including noting the complaints in complaint register complete all as directed by Engineer-in-charge. (Any material required for attending complaints shall be measured and paid separately under respective item herein after)

Labour only for attending day to day electric supply complaints of day to day mantenance of existing LT Panels involving replacement of meterials including connecting electrical accessories / spares of water supply installation from 0830 hrs to 1730 hrs and electrical fitting & light, short circuits in pump house including nothing the complaints from Nodal Point No. I and allied areas in complaints register and distribution to the trademen complete all as directed (any meterial required for atteding complaints shall be measured & paid seperately under respective item here after) Note:- The suitable shift duites as deems fit shall be decision of the Engr-in-charge

Notes for Item No 1.01 & 1.02 :- (i) The complaints shall be attended and the defects shall be rectified by a team of expert and experienced electrician/plumber as applicable assisted with adequate No of helpers complete all as specified and as directed. (ii) The complaints shall be attended and defect shall be rectified within 08 hrs commencing from date and time of notifying the complaint failing which a penalty @ Rs 500/- per complaint per day (08 hrs) shall be levied upon/imposed on the contractor and recovery shall be made from contractor's dues.Contractor rep shall be available wef 0800 hrs to 2000 Hrs to receive and notify the complained (iii) In case, after checking and attending the defect, it is not possible to rectify the defects within 08 hrs the facts shall be brought to the notice of Engineer-in -charge by the contractor /his rep . If Engineer -in-charge is satisfied with contractors view, no recovery will be made. (iv) While attending the complaint of water supply /Electric supply if earth work is required then the same shall be measured and paid seperately under appropriate item of Sch 'A' . However no extra payments shall be made for dewatering. (v) Cutting of GI pipe in position and threading is also deemed to be included in the job rate (Fitting and fixtures will be measured and paid separetely under respective item of Sch A. (vi) All T & P as well as dewatering motor single phase of 3HP with including 100 mtr cable, required for attending the complaints shall be provided by the contracor. (vii) The pipe fitter shall always be in possession of die set complete with cutters , boring Tups , Pipe wrench, Chain wrench,Caulking tools, set of spanners and ladders,wehicle/Ricksha etc Complete,all as required at site.

(viii) The elecrician shall always be in possession of all Electrician tools , LT Megger, Earth tester , Multimeter , Crimping tool, insulation tape, Hand gloves etc complete all as required at site and directed by Engr-in-charge. (ix) All material reqd at site for day to day maintenance shall be issued by Deptt under respective items here in after.

Supply and fixing of GI Socket, medium grade, ISI Marked complete all as specified and as directed of following sizes.

GI Socket 15 mm bore

GI Socket 20 mm bore

GI Socket 25 mm bore

GI Socket 40 mm bore

GI Socket 50 mm bore

Supply fixing of GI Elbow, medium grade, ISI Marked complete all as specified and as directed of following sizes.

GI Elbow 15 mm bore

GI Elbow 20 mm bore

GI Elbow 25 mm bore

GI Elbow 40 mm bore

GI Elbow 50 mm bore

Supply fixing of GI Union, medium grade, ISI Marked complete all as specified and as directed of following sizes.

GI Union 15 mm bore

GI Union 20 mm bore

GI Union 25 mm bore

GI Union 40 mm bore

GI Union 50 mm bore

Supply fixing of GI Nipple, medium grade, 50 to 150 mm long, ISI Marked complete all as specified and as directed of following sizes.

GI Nipple 15 mm bore

GI Nipple 20 mm bore

GI Nipple 25 mm bore

GI Nipple 40 mm bore

GI Nipple 50 mm bore

Supply fixing of GI reducing socket, medium grade, ISI Marked complete all as specified and as directed of following sizes.

GI reducing socket size 20 x15 mm bore

GI reducing socket size 25 x15 mm bore

GI reducing socket size 25 x20 mm bore

GI reducing socket size 50 x40 mm bore

Supply fixing of GI Tee, Medium Grade, complete all as specified and as directed of following sizes

GI Tee , 20 x 20 x 15 mm bore

GI Tee , 20 x 20 x 20 mm bore

GI Tee , 25 x 25 x 20 mm bore

GI Tee , 25 x 25 x 25 mm bore

GI Tee , 40 x 40 x 15 mm bore

GI Tee , 40 x 40 x 20 mm bore

GI Tee , 40 x 40 x 25 mm bore

GI Tee , 40 x 40 x 40 mm bore

GI Tee , 50 x 50 x 15 mm bore

GI Tee , 50 x 50 x 20 mm bore

GI Tee , 50 x 50 x 25 mm bore

GI Tee , 50 x 50 x 40 mm bore

GI Tee , 50 x 50 x 50 mm bore

Supply fixing of GI plug, solid, heavy duty, complete all as specified and as directed of following sizes.

GI plug, 15 mm bore

GI plug, 20 mm bore

GI plug, 25 mm bore

GI plug, 40 mm bore

GI plug, 50 mm bore

Supply fixing of PVC 'L' type holder, suitable for aluminium rod, float ball, of following size bore complete all as specified and as directed.

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply fixing of PTMT float valve, Sizes as under, with epoxy coated aluminium rod and high density plastic ball complete all as specified and as directed.

PTMT float valve, 15 mm bore

PTMT float valve, 20 mm bore

PTMT float valve, 25 mm bore

PTMT float valve, 40 mm bore

PTMT float valve, 50 mm bore

Taking up or down GI steel tubing of following sizes with connections from Trenches/floors/walls including cleaning for refixing or removal complete all as specified and as directed. Note :- Excavation & earth work shall be measured & paid separetely.

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Refixing old steel tubing and connections in new or old position(wall/ ceiling/ floor) of following sizes complete all as specified and as directed. Note :- Excavation for new location shall be measured & paid separetely.

GI steel tubing, 15 mm bore

GI steel tubing, 20 mm bore

GI steel tubing, 25 mm bore

GI steel tubing, 40 mm bore

GI steel tubing, 50 mm bore

Laying and Testing of GI steel tubing medium grade of following size in old or new position as in ceiling/walls/Floors with necessary fixing arrangements and including providing new GI fittings complete all as specified and as directed. Note :- (i) Excavation & earth work for new locations shall be measured & paid separetely. (ii) GI steel tubing shall be issud under Sch 'B' as free for laying/fixing only. (iii) GI fittings should be measured and paid under respective items.

GI steel tubing, 15 mm bore

GI steel tubing, 20 mm bore

GI steel tubing, 25 mm bore

GI steel tubing, 40 mm bore

GI steel tubing, 50 mm bore

Supply and Fixing Gun metal gate valve, with iron wheel head screwed both ends for iron pipe as per IS-778 and fixed including taking out unserviceable one, complete all as specified and as directed of following sizes.

Gun metal gate valve, 15 mm bore

Gun metal gate valve, 20 mm bore

Gun metal gate valve, 25 mm bore

Gun metal gate valve, 40 mm bore

Gun metal gate valve, 50 mm bore

Cutting and screwing the existing steel tubing of following size bore for addition & alteration or lengthening screw on pipe to form connector complete all as specified and as directed.

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

M&L for Disconnection electrical and water connection of the 12.5 HP centrifugal pump and motor with base plate and transported to work shop opening carefully and replacement of bushes, gland packing, ball bearing, rubber gasket nut and bolt fixing the require new parts(parts such as shaft, impellor, coupling & bearing shall be supplied under relevant item of schedule ) and complete re-fixing its in original position and making out all electrical and water connection and testing complete all as specified and as directed by the Engineer-in-Charge. Note :- Rate includes transportation of motor from the place of installation for repairing and reinstalling the same on existing foundation & testing & commisioning.

Supply and fixing shaft suitable for centrifugal pumps

Supply and fixing GM impeller suitable for centrifugal pumps

Supply and fixing MS coupling suitable for centrifugal pumps

Supply and fixing bearing suitable for centrifugal pumps

Supply and fixing Switch Piano flush type 6 amps single pole one way 240 volts complete all as specified and as directed.

Supply and fixing Switch Piano flush type 16 amps, single pole, one way, 240 volts complete all as specified and as directed.

Supply and fixing Switch Socket outlet 2 in 1, 3 pin, 6 amps 240 volts complete all as specified and as directed.

Supply and fixing Switch Socket outlet 2 in 1, 3 pin, 6 and 16 amps 240 volts complete all as specified and as directed.

Supply and fixing Switch Socket combination 2 in 1, 3 pin, 6 amps 240 volts complete all as specified and as directed.

Supply and fixing Switch Socket combination 2 in 1, 3/5 pin, 6 and 16 amps 240 volts complete all as specified and as directed.

Supply and fixing MCB SP, 6 to 32 Amp, 240 volts complete all as specified and as directed.

Supply and fixing LED batten arrow for multi application suitable for 18 Watts with & including necessary cable connection to make it functional complete all as specified and as directed.

Supply and fixing non metallic PVC conduit 25 mm bore, medium grade having 2 mm wall thickness with & including all fittings such as tee,bends, reducer, elbow, bell mouth, tube ends etc with all other fixing accessories such as couplers, locknuts saddles ,pipe hooks, clips etc complete all as specified and as directed.

Supply and fixing PVC multistranded aluminium conductor, 1100 volts grade , cross sectional area 4 sqmm, 2 core fixed on panels/walls complete all as specified and as directed.

M&L for rewinding of electrical motor 12.5 HP with super enameled copper winding wire of suitable size not less than original after cutting and taking out old winding complete with all insulation material such as Colton top varnish etc of centrifugal pump set motor complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing lead pig for joints complete all as specified and as directed.

Supply and fixing Spurn Yarn complete all as specified and as directed.

M&L for CI/ DI Pipe fittings such as Tees, bends ,any type, radius and angle/tapers any type, collars,tail pieces,caps and plugs up to 150 mm bore conforming to IS: 1538-1993 complete all as specified and as directed.

M&L for CI/ DI Pipe fittings such as Tees, bends ,any type, radius and angle/tapers any type, collars,tail pieces,caps and plugs 200 to 300 mm bore conforming to IS: 1538-1993 complete all as specified and as directed.

Supply only 15 mm bore Bib tap of PTMT, any tint, high pressure screwed for male/ female threaded, for pipe of size 15 mm bore complete all as specified and as directed.

supply and fixing PPR Gate valve(Brass inserted), ISI Marked of following size, Complete all as specified and as directed.

20 mm Bore

40 mm Bore

50 mm Bore

supply and fixing in replacement PPR male threaded adopter, ISI marked of following size, Complete all as specified and as directed.

20 mm Bore

40 mm Bore

50 mm Bore

Excavation in trenches not exc 1.5 M wide and not exc 1.5 M in depth for pipe line, etc in soft/ loose soil getting out and levelling of bottom surface to required level all as specified and as directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed.

Removing excavated material to a distance not exc 50 m and depositing where directed not exc 1.5 meters above the starting point complete all as specified and as directed.

Supply and fixing in replacement of MCCB 3 pole 100 Amps 25 KA complete all as specified and directed.

Supply and fixing in replacement of MCCB 3 pole 63 Amps 25 KA complete all as specified and directed.

Supply and fixing Single headed Gun Metal fire hydrant landing valve type A (single head outlet) of 80mm dia landing valve with 63mm dia female outlet complete and 80mm inlet with rubber blank cap and chain as per IS 5290-1983, suitable for brigade hose of 63mm with couplings conforming to IS 903 including taking down the existing one complete all as specified and directed.

Supply and fixing of weather proof standard fire hose box made of 16 SWG gauge MS Sheet 750mm x 600mm x 250mm with double door with 4mm thick glasses and door frame including locking arrangement by allen key, stove enamelled fire red finish with 'Fire hose' marked on front and brilliant white inside yard, suitable for housing of 2 lengths RRL hose pipe conforming to IS:636-1979 (type-II) of 63mm dia. GM instataneous male and female coupling (IS:903) and branch pipe and nozzel 12.5mm dia including taking down the existing one complete all as specified and directed .

Supply and fixing in position 63mm nominal bore and 15 mtr long synthetic fibre, circular woven jacketed, rubberized fabric reinforced rubber lined (RRL) fire hose pipe of approved make bearing IS : 636-1988 type A mark and having TAC and MMD approval with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS : 903) bound and riveted to the hose pipe with copper rivets and copper wire, complete all as specified and including taking down the existing one complete all as specified and directed .

Supply and fixing in position Gun Metal 63mm dia short size branch pipes with 20 mm dia nozzles with 63mm instantaneous coupling ISI marked (IS: 903). and including taking down the existing one complete all as specified and directed.

Supply, fixing, testing and commissioning of wall mounting swinging type First aid fire hose reel with drum, hanging bracket,Thermoplastic rubber (first aid hose) as per IS 12585 20 mm dia 30 mtr length to with stand 10 kg per Sq cm working pressure fitted with gunmetal nozzle and shut off valve of any size complete all as specified. The hose reel shall be conforming to IS 884-1985 including for 25 mm dia MS pipe connection from riser to hose reel sockets,nipples,elbows,valve etc. Drum shall be fixed on adjoining wall through anchor fasteners/cement concrete hook or MS stand as per site requirement and the rate for fixing/hanging items in the rates quoted(for internal hydrant and one each an either side of stage) including taking down the existing one complete and depositing to MES store yard all as specified and directed .

Supply and fixing water delivery Thermoplastic rubber (first aid hose) as per IS 12585 20 mm dia 30 mtr length to with stand 10 kg per Sq cm working pressure fitted with gunmetal nozzle and shut off valve of any size complete and depositing to MES store yard all as specified and directed.

Supplying & fixing Co2 type 4.5 kgs capacity Fire Extinguisher, assembled from brand new Explosives approved cylinders, complete with screw-down type valve, internal discharge tube, one metre high pressure rayon braided hose, discharge, horn, Bearing ISI Mark IS: 2878. Co2 Cylinder as per IS: 7285 CCE approved ‘ISI’ Valve as per IS: 3224. Co2 Gas as per IS: 15222. internal discharge tube IS: 738. Discharge duration, 10-18 secs. Filled weight of extinguisher, 17 kgs. Tested to 250 kgf/cm2 complete all as specified and as directed .

Supplying & fixing ABC type Stored Pressure 6 kgs capacity Fire Extinguisher, fabricated from MS sheets, fitted with brass forged squeeze grip valve assembly incorporated with pressure gauge, initial charge of 5 kgs. ABC Powder(MAP 50%) and pressurized with nitrogen gas. M.S. Body as per IS : 513 Forged Brass valve as per IS: 6912. Bearing ISI Mark IS: 13849 complete all as specified and as directed .

Supply, fixing, testing and commissioning of 150 dia mm pipe heavy duty class "c" MS pipe ,ISI marked as per IS: 1239 with all necessary fittings & fabrication like tees, elbows, flanges, reducers, gaskets, nuts and bolts etc welding or screwed joints as required including fixing of pipe with necessary standard clamps structural steel supports as required/directed at site including painting of two coats of synthetic enamel paint of post office red colour over a coat of red oxide primer including taking down the existing one complete all as specified and directed .

All as per Srl item No. 52 here-in-before but size 100 MM.

All as per Srl item No. 52 here-in-before but size 80 MM.

Supply, fixing, jointing & testing cast Iron Sluice Valve of size 80 mm dia ISI Marked, flanged ends drilled pressure rating PN-1.0, PD Short body, Confirming to IS 14846 -2000, having stainless steel spindle with cast iron operation wheel at top including taking out unserviceable sluice valve complete all as specified and as directed .

All as per Srl item No. 55 here-in-before but size 100 MM.

All as per Srl item No. 55 here-in-before but size 150 MM.

All as per Srl item No. 55 here-in-before but size 200 MM.

Supply, fixing, jointing and testing of Cast iron Non Return valve of size 80 mm dia without by pass arrangement , Swing type, confirming to IS 5312, flanged ends pressure rating PN 1.0 complete including taking out unserviceable NRV complete all as specified and as directed . Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item.

Supply, fixing, jointing and testing of Cast iron Non Return valve of size 100 mm dia without by pass arrangement , Swing type, confirming to IS 5312, flanged ends pressure rating PN 1.0 complete including taking out unserviceable NRV complete all as specified and as directed . Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item.

Supply, fixing, jointing and testing of Cast Iron Butterfly Valve of size 80 mm dia ISI marked class (PN 1.0) including taking out unserviceable Butterfly valve complete all as specified and as directed . Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item.

Supply, fixing, jointing and testing of Cast Iron Butterfly Valve of size 100 mm dia ISI marked class (PN 1.0) including taking out unserviceable Butterfly valve complete all as specified and as directed . Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item.

Supply, fixing, jointing and testing of Cast Iron Butterfly Valve of size 150 mm dia ISI marked class (PN 1.0) including taking out unserviceable Butterfly valve complete all as specified and as directed. Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item.

Supply, fixing, jointing and testing of Cast Iron Slim seal dual plate wafer type check valve of size 100 mm dia ISI marked class (PN 1.0) including cutting the existing pipe ,complete all as specified and as directed. Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item.

Supply, fixing, jointing and testing of Cast Iron Slim seal dual plate wafer type check valve of size 150 mm dia ISI marked class (PN 1.0) including cutting the existing pipe ,complete all as specified and as directed . Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item.

Supply, fixing, jointing and testing in replacement of Bourdon type pressure gauge with gun metal isolation cock and copper ‘U’ Tube.having calibration of 0-10 Kg/cm2 ,and 100 mm dial size all as specified including taking out unserviceable pressure gauge complete all as specified and as directed .

Supply, fixing, jointing and testing in replacement of Pressure switches IPS 100 or approved equivalent) including making connections with the control panel and the pressure vessel complete in all respects.The electrical continuity is maintained between contacts NC& COM under normal conditions. The contacts changeover to NO & COM on rise of pressure to preset value all as specified including taking out unserviceable pressure switch complete all as specified and as directed.

Supply, fixing, jointing and testing in replacement of Gun metal Air release valve of size 25mm dia having rubber ball ( of suitable range and calibrated) complete screwed both ends for iron pipe, ISI Marked, as per IS: 778 of following sizes including taking out unserviceable air release valve complete all as specified and as directed.

Disconnecting & taking out unserviceable Gun metal 3 way Fire brigade inlet to down commer line dismantling and opening carefully for servicing over hauling shifted to and fro to workshop,material and labour for replacement of unserviceable &worm out GM Parts and rubber packing BNW etc complete and refixing same in position and testing all as specified and as directed .

Disconnecting & taking out unserviceable 100 mm dia Non Return Valve dismantling and opening carefully for servicing over hauling shifted to and fro to workshop,material and labour for replacement of unserviceable & worm out SS flapper,square Nut,Body Nut- Bolts,Gland nut -bolts,Gland packing etc,including machining and greasing,reassembling and refixing in position and testing complete all as specified and as directed. Note - The cost of washers,gaskets and gun metal flaper & stinless steel spindle of non return valve packing nut bolt etc shall be deemed to be included in the quoted rates.

Material and labour for in repairs / fabrication of base frame with MS Chanel MC-25/50/75/100/125 for foundation of centrifugal pump set incl two coat red oxide and black enamel paint all as specified and as directed

Taking out old rusty MS base frame incl dismentling the pump & moter, breaking PCC foundation complete all as per the site requirement and as directed .

Material and labour for painting with synthetic enamelled paint as per approved colour code of fire fighting Riser Pipe line in Fire nitch ground floorto terrace pipe lines inside the shaft complete all as specified and as directed .

Material and labour for painting with synthetic enamelled paint as per approved colour code of fire fighting station induction motor coupled with fire pump on terrace pump house complete all as specified and as directed .

Supply, fixing, jointing and testing in replacement of manual call point break glass type enclosed in M S enclosures body of 3 mm thickness complete with chain and hamer and incl inscriber in case of fire break glass complete including taking down the existing one complete all as specified and directed .

Supply, fixing, jointing and testing in replacement of electrically operated Electronic Hooter enclosed in MS enclosures of suitable size painted with sythetic enamaled paint red coloured complete with suitable transformer including taking down the existing one complete all as specified and directed by Engr-in-Charge.

Servicing of Cubical type wall mounted fire pump control Panel for 12.5 HP Motor fabricated from 16 Swg MS sheet duly complete including replacement of UNSV parts all as specified and as directed . Note:-Any spare parts if required deemed to be quoted in this rates.

Supply and fixing, testing and commissioning of floor mounting type cylindrical pressure vessel with supporting legs, size 200 mm dia and 1.5 Mtr high with dished end and knuckle radius (IS:2062). The vessel shall be made of 8mm thick MS plate welded alround with sockets/flanges welded for inlet, outlet and scour pipes, pressure gauge, pressure switches, air release valve etc. of suitable required size. The pressure vessel shall be painted inside with anti-corrosive epoxy paint and outside with two or more coats of synthetic enamel paint of Fire red colour over a coat of ready mixed primer, both of approved quality, complete all as specified and as directed by the Engineer-in-Charge.

Supplying and drawing 1.5 sqmm of PVC insulated copper conductor, single core cable in the existing surface/recessed PVC/Steel conduit /PVC casing and capping as required complete all as specified and as directed by the Engineer-in-Charge.

Supply & Fixing 4 mm plain glass along with Rubber Beating etc change in FHC complete all as specified and as directed by the Engineer-in-Charge.

Supply, fixing, testing Nozzle with shut off valve including 25 mm clipco clamp for Hose Reel of any size complete all as specified and as directed by the Engineer-in-Charge.

Servicing of Single headed Gun Metal fire hydrant landing valve type A (single head outlet) of 80mm dia landing valve with 63mm dia female outlet complete and Lugs, GM nut,Coupling complete all as specified and as directed by the Engineer-in-Charge. Note :-Any spare parts if required deemed to be quoted rates.

Servicing ,fixing, testing of wall mounting swinging type First aid fire hose reel with drum, hanging bracket, for 25 mm dia MS pipe connection from riser to hose reel sockets,nipples,elbows,valve etc. Drum shall be fixed on adjoining wall through anchor fasteners/cement concrete hook or MS stand as per site requirement complete all as specified and as directed by the Engineer-in-Charge. Note:- The rate for fixing/hanging items deemed to be quoted rates.

S/F in replacement Pad Lock verical type size 75mm having duplicate key 7 lever and SS Handle in Existing FHC complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down CI/DI Pipe of following sizes including all fittings) with spigot and socketed ends and lead tyton joints including burning out lead joints and recovering lead and including cleaning for refixing or removal, making good disturb surface complete all as specified and as directed. Note:- Excavation & earth work shall be measured & paid separetely.

100 mm bore

150 mm bore

100 mm bore

150 mm bore

Material & Labour for run lead joint including jointing material for CI/DI Pipe of following sizes complete all as specified and as directed .

100 mm bore

150 mm bore

S&F in replacement rotational moulded polyethylene water storage tank ,cyclindrical vertical with closed top 500 Litres capacity tripple layered hoisted and fixed in position after taking down as existing at site (of any capacity ) all as specified and as directed

S&F in replacement rotational moulded polyethylene water storage tank ,cyclindrical vertical with closed top 500 Litres capacity tripple layered hoisted and fixed in position after taking down as existing at site (of any capacity ) all as specified and as directed

S&F CI NRV of folllowing sizes complete all as specified and directed :

100 mm dia.

150 mm dia .

M&L for fabrication / welding work of MS Header / any size upto 400 mm MS Pipe at various Pump House for arresting lekages on header complete all as specified and directed

Supply, installation and testing flanged ends strainer/dirt box rating PN 10 of following sizes with stainless steel mesh suitable for cold water meter to avoid foreign material entering into meter and making good connection with flanged ends with gasket rubber sheet and nut & bolts fixing in horizontal/inclind/vertical position, including taking out unsv strainer/dirt box complete all as directed . Note :- Flange joints including jointing materials shall deemed to be included in the unit rate of this item.

100 mm bore

150 mm bore

200 mm bore

Supplying and fixing in replacement UPVC pipes, of following sizes, pressure rating 10 kgf/cm2, heavy duty, including taking out with all pipe fittings such as ends, elbows,unions, tees, reducing tees, adoptors, sockets, plugs, hose clips etc. fixed to walls with fixing arrangements such as saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves , ceilings or in floors etc., complete with and cutting through walls, floors and their making good or laying in trenches and also cutting, screwing and waste including jointing with jointing material complete all as specified and as directed. Note :- Excavation & earth work for new location shall be measured & paid separetely.

15 mm Bore

20 mm Bore

25 mm Bore

40 mm Bore

50 mm Bore

90 mm Bore

110 mm Bore

Supply and fixing UPVC Socket, ISI Marked complete all as specified and as directed of following sizes

UPVC Socket 15 mm bore

UPVC Socket 20 mm bore

UPVC Socket 25 mm bore

UPVC Socket 40 mm bore

UPVC Socket 50 mm bore

UPVC Socket 90 mm bore

UPVC Socket 110 mm bore

Supply and fixing UPVC Elbow, ISI Marked complete all as specified and as directed of following sizes

UPVC Elbow 15 mm bore

UPVC Elbow 20 mm bore

UPVC Elbow 25 mm bore

UPVC Elbow 40 mm bore

UPVC Elbow 50 mm bore

UPVC Elbow 90 mm bore

UPVC Elbow 110 mm bore

Supply and fixing UPVC reducing socket, ISI Marked complete all as specified and as directed of following sizes.

UPVC reducing socket size 20 x15 mm bore

UPVC reducing socket size 25 x15 mm bore

UPVC reducing socket size 25 x20 mm bore

UPVC reducing socket size 40 x20 mm bore

UPVC reducing socket size 50 x20 mm bore

UPVC reducing socket size 50 x40 mm bore

An amount of Rs 1,11,055.00 shall be deducted from BOQ on account of schedule of credit