PROVISION OF OVER HEAD SHELTER AND KOTA STONE FLOORING IN WATER CHERRY LOCATION AT A COY OF NO 4 TRG BN MT CATR OF ASC CENTRE SOUTH 2 ATC INCLUDING CERTAIN REVENUE WORKS UNDER GE CENTRAL BANGALORE

Amount

Surface dressing n.exc 15 cm deep as in soft/loose soil and disposal to a distance not exc 50m complete all as specified and directed.

M & L for surface excavation averaging 15cm deep and n.exc 30cm deep and getting out as in soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) in hard/dense soil each n. exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25cm, watering and removing surplus soil to a distance n. exc 50m and making good surface as directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc area not exceeding 10 Sqm on plan and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material to a distance not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

Removing excavated material to a distance exc. 250 m and not exc 500m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M&L for precast cement concrete block masonry type C1, 1:3:6 (20 mm graded granite stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 (Nominal Mix) (Using 20 mm graded stone aggregate) as in foundation, footings foundation beams, plinth beams etc complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 (Nominal Mix) (Using 20 mm graded stone aggregate) as in columns, pillars, piers, post and struts etc complete all as specified and directed.

M & L for use & waste Form work to sides of concrete foundations, footings, raft beams, sides and soffits of plinth beams and the similar works for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to sides of concrete columns, pillars, piers, post and struts and the similar works for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for Hardcore of broken/crushed stone aggregate of gauge n.exc 63 mm deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for 40 mm thick, plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in floors laid in panels, finishing the surfaces even & smooth with using extra cement complete all as specified and directed.

M & L for 100mm thick Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub-base of floor, etc complete all as specified and directed.

M & L for 75mm thick Plain cement concrete 1:2:4, type B-1- (using 20 mm graded stone aggregate) as in floors laid in panels, finishing the surfaces even & smooth without using extra cement complete all as specified and directed.

M & L for precast chequered cement concrete tiles of size 20cm x 20cm x 20mm thick, as in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring, self finished, 20 to 25mm thick laid and and jointed in grey neat cement slury and pointed in coloured cement to match with the shade of the stone slab including providing 20mm thick screed bed in CM 1:4 including rubbing, polishing complete all as directed.

M & L for glazed ceramic, coloured tiles 7 to 8 mm thick area of each tiles not exc 0.06 sqm as in skirting/dado/vertical surfaces of wall including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (Total coated thickness) of any colour, finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with best quality self tapping screws as specified

S & F Pre-Painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and directed. (Colour of ridge shall be same colour as that of sheet used for roof)

S & F TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F TMT steel bars 6 to 10mm dia, cut to length, bend to shape required, including cranking, bending spirally as in tie/stirrups of columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F Rolled mild steel work as in posts etc using Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc including cutting, welding complete. Steel section conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed.

S & F Rolled mild steel work as in trusses, purlins, rafter etc using Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc including cutting, welding complete. Steel section conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed.

S & F mild steel work in tubular trusses, post fixed independently, purlins using ERW or butt welded tubes conforming to IS 1161-1998, grade YSt-240, including cutting, welding complete all as specified and directed.

S & F band, straps, supports or stays for rainwater pipes, ventilating pipes, including bolts if required hooks (stay), heavy duty, for large gate, hooks and pintle hinges, large hasp and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, wind ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and the similar small articles conforming to Fe-290 Gde- E-165 all as directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:4 on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 10 mm thick in cement mortar 1:3 on concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M &L for writing letters or figures (Block, Roman, Italic or Indian) 10cm high using synthetic enemal paint complete all as directed.

M &L for writing letters or painting of stops, commas, short lines, dashes, hyphens, brackets etc using synthetic enamel paint complete all as directed.

PRANAVI CONSTRUCTION

Vajra Constructions

DIVYA CONSTRUCTIONS

S R CONSTRUCTIONS

SHRI NARAYANADRI ENGINEERS & BUILDERS