PROVN OF GAS QUAD GRILL CONTAINER AND PANTRY SHELF AND ALLIED WORKS AT DSRV IN WED MANKHURD, DEM AND RECONSTR OF ONE STATIC WATER TANK AT WED MANKHURD AND ADDN/ALTN AND SPL REP TO ADAM BLOCK AT CSD MUMBAI AREA DEPOT UNDER GE (NW) MANKHURD

Amount

Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing the retreived debris out side MD land, complete all as specified and directed.

M&L plain cement concrete in foundations filling and mass concrete type D-2 1:4:8 ( 40 mm graded aggregates ) complete all as specified and directed

M&L for Pre cast cement concrete block masonry with solid block of grade(C-5) having block density not less than 1800 Kg/cum, exc, 10cm in width and setting in CM 1: 6, complete all as specified and directed.

M&L rendering 15 mm thick on fair faces of brick surfaces in CM(1:6) finished even and smooth with out using extra cement complete all as specified and directed

M & L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper with roller over one coat of primer, complete all as specified and directed.

M&L for 3 mm thick (minimum) white cement based wall care putty in two coats on new or old surfaces of walls/ceilings etc, finished even and smooth, complete all as specified and directed.

M&LScreed bed or bedding layer or mortar 15mm thick for laying floor finishes in CM 1:6 complete all as specified and directed

M&L for Granite of any type 25 mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and fixing over cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed

S&F Kitchen Sinks made of stainless steel grade AISI-305, 1 mm thick including provision of plugs, washers, brass CP waste coupling/ fittings and 40mm bore PVC waste pipe, mild steel cantilever brackets, overall size 495 x 420 mm, bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S&F 15mm bore brass CP Bib Tap, Make ESSCO Cat No MQT-511 or equivalent of make Parko/Zoloto as approved by the GE, complete all as specified and directed.

S&F 15mm bore brass CP stop valve, Make ESSCO Cat No MQT-513 A or equivalent of make Parko/ Zoloto as approved by the GE, complete all as specified and directed.

Supply & fixing 16 mm outer diameter CPVC pipes UV stable,leak proof, tough ,rigid , conforming to IS:15778 of SDR 11 standard with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F cast iron Nahani trap with 75mm dia out let including grating, connecting, jointing to waste pipe with lead joints, also including embedding the same in PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) mixed with water proofing compound in the proportion as recommanded by the manufacturer(s), by hacking out concrete joints and making good of surfaces, complete all as specified and as directed .

M & L for filling of lean concrete 1:5:10 type E2 (using 40 mm graded stone aggregates ) for filling in sunken portion, as per requirement, complete all as specified and directed.

S&F 75 mm bore uPVC (SWR) Bends with and including oval access door and also including rubber ring joints, complete all as specified and directed.

S & F of 75 mm bore uPVC (SWR) soil, waste, ventilating rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc complete all as specified and directed.

M&L 1.6mm thick plain MS Sheet for base of water cooler , moulded to requirements all as specified and directed by Engr in Charge.

M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete FE -290 Gde E-165 etc complete all as specified and directed.

M&L for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Dismantling completely existing roof treatment (excluding cement screed bed ) including loosened cement plaster and exposing the top surface of RCC slab and making good the same in CM 1:4 and removing rubbish, etc to a distance exceeding 500m and not exceeding 1.0km complete all as specified and directed

M&L raking/scrapping out 3mm joints of tiles completely and pointing/tile grouting it with polymer modified non shrink, dimensionally stable , fungus resistance, colour fast ,water resistant of make Dr Fixit, Krishna Conchem , Sika , STP complete all as specified and directed.

M&L 10 mm thick in CM (1:3)) mixed with WPC by 3% weight of cement screed bed when the concrete is still green complete all as speicified and directed.

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%. (xi) Applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane surface.

Taking down cement plaster or lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retreived debris out side MD land including necessary scaffoldings etc complete all as specified and directed

M&L for 20 mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing surfaces even and smooth, complete all as specified and diected Note: The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with ready mix plaster and nothing extra shall be payable on this account.

M&L for leakage / seepage proof coating consisting of preparing the new surfaces of existing exterior walls, parapet walls, chajjas etc. and applying Primeseal primer of M/s Dr Fixit or equivalent chemical of M/s STP Ltd as approved by the GE or one coat of Chemstic PDE 600 elastomeric coating (and allowing to dry for 8hrs) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat of M/s Dr Fixit with DFT 100microns or Shalicryl 215 of M/s STP Ltd or Chemstic PDE 600 elastomeric coating (the surfaces after painting one coat shall be allowed to dry for 6 to 8hours before application of next coat) including necessary scaffolding etc complete all as per manufacturer instructions, as specified & directed. Note: The aforesaid treatment shall be got executed by the contractor from the authorised applicator of the manufacturer(s) and also necessary authenticated documents on account of above shall be submitted by the contractor to the GE.

S&F stairs (framed) including stringers , treads , landing , balusters , hand rails etc , including cleats , brackets , etc complete FE-290 Gde E- 165.complete all as specified and directed

M& L for preparation of new steel and iron surfaces of any description , over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a priming coat of red oxide zinc chrome primer complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for including cutting of the reinforcement to facilitate demolition and removing the retreived debris out side MD land, complete all as specified and directed.

M&L for RCC 1:1.5:3 type type A-1 (using 20mm graded stone aggregate) as in chajjas or similar items like finsfasia complete all as specified and directed.

M&L for CRS steel bars 10mm dia and over in reinforcement cut to length, bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and directed. Note : This item is applicable for new RCC Members as well as for provision of additional steel bars in the existing RCC Members.

Use and waste formwork to chullah hoods, chajjas, troughs and similar items including edges for fair finished flat surfaces of the concrete, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in coping, bed blocks, roof curb, mud stops, coving at junction of wall and chajjas etc including weathering, slightly rounded or chamfered angles, provision of necessary form work, complete all as specified and directed.

Dismantling of 150 mm bore drain pipes (salt glazed ware , AC or PVC ), jointed in cement mortar and taking out of trenches, complete all as specified and directed.

S&F 150 mm bore Upvc (SWR) Bends with and including oval access door and also including rubber ring joints , complete all as specified and directed.

S & F 150 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including rubber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonary built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, also including removing rubbish outside MD land, complete all as specified and directed.

M&L Brickwork with subclass 'B' bricks , straight or curved on plan exc 6 m mean radius , built in CM 1:6 complete all as speicified and directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

M & L Bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering complete all as specified and directed

Surface excavation n.exc. 30 cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified and directed

Removing excavated material n.exc 50 mtr and depositing where directed complete all as specified and directed

M & L broken stone hardcore of gauge exc 63 mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed

M & L PCC 1:3:6 type C2 using 40 mm graded aggregate as in foundation, filling, flooring, plinth protection and mass concreting complete all as specified and directed

M & L RCC M-30 mix design using 20 mm graded aggregate as in foundation, base slab complete all as specified and directed Note : Design mix shall be carried out from approved lab such as IIT/ NIT/ SEMT Pune, Govt Engineering Colleges or any NABL approved lab.

M & L RCC M-30 mix design using 20 mm graded aggregate as in vertical walls complete all as specified and directed Note : Design mix shall be carried out from approved lab such as IIT/ NIT/ SEMT Pune, Govt Engineering Colleges or any NABL approved lab.

M&L RCC M-30 mix design using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, cover slab and in shelves and the like all as specified and directed. Note : Design mix shall be carried out from approved lab such as IIT/ NIT/ SEMT Pune, Govt Engineering Colleges or any NABL approved lab.

Use and waste formwork to sides of fair finish surface of concrete foundations, base slab, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work complete all as specified and directed

Use and waste formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc. for fair finished surafce complete all as specified and directed

Use and waste formwork to sides and soffits of suspended slabs such as roof slabs,cover slab, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surface complete all as specified and directed

M & L for providing 2 coats of polymer modified cementitious slurry on inside face of wall and base slab and outside face of wall complete all as specified and directed

S & F Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles of articles exc 5 Kg complete all as specified and directed

M & L 50 mm dia `medium grade', galvanised iron , with all fitting; laid in trenches, floors and walls complete all as specified and directed

M & L 50 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed Note : A sum of Rs 9,630.00 towards sch of credit shall be deducted to arrive the contract sum

sahajanand const co.

Vishal Builders

joshua construction