Renovation Work of Office Part, Waiting Room, VIP Waiting Rooms, Portico, Car Parking Shade at RDC and SDO Residence (Occupied by Honble Chief Minister) at Kanke Road, Ranchi

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board.

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds. Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70mm & above) x (40mm & above) & both glazed and fly screen sash (25mm & above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 meter).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Stainless steel wire guage (Grade-304) aperture 1.4 mm and 0.50mmdia wire

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab upto 0.50 sqm

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing and applying integral crystalline (dry shake) of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab, sewage & water treatment plant slab, warehouses floor, parking structures and water tank base slab etc. sprinkled @0.60kg per sqm or higher as recommended by the manufacturer’s specification over the lean concrete of above cited structures. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 85%, compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dryshake shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litres/10 sqm, complete as the direction of Engineer -in-Charge.

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Finalo coat to be done in 1 or 2 layers without gap of time.)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr / 10sqm

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4 mm thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face# 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 TS / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Carriage of Material

Bricks - 8km (1k + 7p)

Sand - 20 km

stone Chips - 22km

Point wiring in PVC conduit with modular type switch:- Wiring for light point /fan point /exhaust fan point /call point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch ,modular plate, suitable size G.I. box etc.as required. Group B

Twin control point wiring in PVC conduit with modular type switch:- Wiring for twin control light point witch 1.5sq.mm FR PVC insulated copper conductor single core in surface/recessed PVC CONDUIT, 2 way modular, type switch, modular plate, suitable size G.I. box etc .as riquied.

power plug wiring in PVC conduit(2x4sq.mm):-wiringfor light power with 2x4 sq mm FR PVC insulated copper conductor single core in surface/recessed PVC conduit along with 1 Nos. 4 sq. mm FR PVC insulated copper conductor singl core cable for loop earthing as requied.

Circuit/submain wiring in PVC conduit:- Wiring for circuit/submain wiring along with earth with following sizeg PVCinsulated copper conductor,single core cable in surface/recessed PVC conduit as requied.

2x1.5sq mm+ 1x1.5sq mm earth wire

2x2.5sq.mm+1x2.5sq.mm earth wire

2x6.0sq.mm+1x6.0sq.mm earth wire

4x10sq.mm+2x10sq.mm earth wier

S/F Modular type switch/socket:- Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including modular plate us required.

5/6amps,one way switch

15/16 amps, one way switch

5/6 amps,3 pin socket outlet

15/16 amps, 6 pin socket outlet

S/F Modular type electronic fan regulator:- Supplying and fixing 2 modules Stepped type electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as requried. (Make :-Havells, Legrand , Anchor, Schneider.)

S/F Modular blanking plate:- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. (Make - Havells, Legrand , Anchor, Schneider.)

Supply and fixing of following size/ modules, GI box along with modular base & cover plate for modular switch/ regulator in recess, including connection as required. (Make :- Havells, Legrand , Anchor, Schneider).

1 or 2 module (78mmx78mmx45mm)

6 module (78mmx205mmx50mm)

S/F light plug point with type accessories :-supplying and fixing suitable size G.I. box with moudular plate and cover in front on surfesh or in recess including providing and fixing 3 pin, 5/6 mps moudular socket outlet and 5/6 mps modular type switch connection, painting etc. us rquoired. (for li

S/F light plug point with type accessories :-supplying and fixing suitable size G.I. box with moudular plate and cover in front on surfesh or in recess including providing and fixing 6 pin, 15/16 mps moudular socket outlet and 15/16 mps modular type switch connection, painting etc. us rquoired.

S/F ceiling roase:- suppliying and fixing 2 pin mps. Ceiling roase on the existing juction box/woon bolck including connection etc. as required

S/F batten holder:- supplying and fixing batten/ angle holder incuding connection etc as required.

ITC ceiling fan:- Installtion, testing and sonnissoning of ceiling, including wiring the down rods of standard length (op to 30cm) with 1.5 sq.mm FR PVC insulated. Copper conducotr, single core cable etc. as required.

ITC exhaust fan upto 450 mm. swee:- Installation of exhaust fan op to 450 mm. sweep in the existing opening, including making the hole to suit the size of the above commissioning etc as required.

S/F s.p. MCB DB:supplying and fixing following way single pole neutral sheet,MCBdistribution board,240 volts,on surface/recess,completewith tinned copper busbar,neutral busbar,earth bar,din bar, detachable gland plate,interconnection,phosphatized and powder painted including earthing etc asrequierd.(But without MCB/RCCB/lsolator)

12way Double door

16way Double door

S/F s.p. MCB DB:supplying and fixing following way three pole neutral sheet,MCBdistribution board,415volts,on surface/recess,completewith tinned copper busbar,neutral busbar,earth bar,din bar, detachable gland plate,interconnection,phosphatized and powder painted including earthing etc asrequierd.(But without MCB/RCCB/lsolator)

6way(4+18),Double door,Horizontal type

8way(4+24),Double door,Horizontal type

S/F 'c' series, S.P. MCB:-Supplying and fixing following, ,240 volts,'c' series,miniature circuut breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections,testing and commissioning etc.asrequied.

6/32amps, single pole

40amps, DP

50/63 amps,TPN

S/F SP MCB blanking:- supplying and fixing single pole blanking plate in existing MCB DB complete etc.as required.

S/F SPN RCCB:- supplying and fixing following rating,double pole (single phase and neutral)240 volts,residualcurrent circuit breaker (RCCB),having asensitivity current upto300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc.as required.63amps

S/F 20amps SPN MCB industrial socket outlet:- supplying and fixing 20amps,240 volts,SPN industrial type,socketoutlet,with 2pole and earth,metal enclosed plug top along with 20amps 'c' series,SP MCCB,in sheetsteel enclosuer,on surface or in recess with chainedmetal cover for the socket outletand complete with connections,testing and commissioning etc.as required.

P/F M.V.danger notice plate:- providing and fixing M.V danger noticeplate of 200mmx150mm,made of mild steet,at least 2mm thick, and vitreous enamelled with on both sides,and with inscrition in single red colour on front side as required.

G.I. Earth pipe eletrode with salt/charcoal:-Erthing with G.I erth pipe 4.5 mtr long,40mm dia inculuding accessories,and providing masonare enclosure with cover plate having locking arrangment and watering pipe etc.with charcoal and salt as required.

S/L 6 SWG G.I. wire in ground:- Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor erthelectrode,including soldering etc.as required.

ceiling fan 48" (1200mm) BLDC Sstar 15:374:2079

SITC of 230 mm (9") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make :- Polar/Usha/Crompton / Havells.

SITC of following rating recess/surface mounted LED round/square shape Down Light Luminarie with pressure die-cast housing for single phase supply voltage. Luminarie shall be confirm to IS; 10322 part-5/section-2 or IEC 62722 with all necessary accesoreies as required. (100l/w , 5700K Cool white, rated voltage- 220/240V. (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs, and two years warranty) Make:-Havells/Philips/Bajaj/ Jaquar. Make 0f LED Philips/Osram/Cree/Nichia.

12 W Round Surface Down light

15/16 W Round Surface Down light

15W COB based round LED light with multiple bem angles (36 Degree)

30W COB based round LED light with multiple bem angles (36 Degree)

Supply fitting and fixing of PVC/XLPE insulated PVC sheathed heavy duty Al. armoured cable for workingvoltage up to and including1100 Volts confirming to IS 1554 (part-1)Make:- Havells, KEI, Finolex, Polycab.3.5 Core 25 Sq. mm

1.1 KV Cable End Termination:-Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required.

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms.

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal bore. Weighing not less than 32 gms.

Supplying, fitting and fixing vitreous white glazed earthen ware l.W.C. of parry Hindustan or any other l.S.S.approved make with 100mm H.C.l. 'p'trap lS litres C.l. pull and let go flushing cistern of names or other l.S.S.equivalent make, complete with allfittings,C.l. or C. C.brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.l. chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 1Smm C.l. body brass spindle stope cock of weight not less than SOgrms, 15mm P.V.C. connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) 580 mm.lonq, (c) With 10lit. low level PVC cistern

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing PTMT grating of approved quality and colour. Circular type. 125 mm nominal dia with 25 mm waste hole.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length.

Special type C.P. Bath room Fitting for V.I.P.Buildings(JAL, Jaquar, Mark or Equivalent)

(iv) Bib Cock (Long Thread) (lSl Marked)

(ii) Pillar Cock (Long neck) (lSl Marked)

(vi) Angular Stop Cock (Long Thread) (lSl Marked)

(xxi) Towel Rail24"

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work

25 mm nominal outer dia. Pipes.

32 mm nominal outer dia. Pipes.

40 mm nominal outer dia. Pipes.

Making holes in walls for laying GI pipes and restoring the same as per specification and direction of E/I.

125 mm thick wall

250 mm thick wall

Providing and fixing GM non-return valve Horizontal type of approved as per specification and direction of E/I. Horizontal non-return valve 32 mm dia weight not less than 600 gm .

Providing and fixing GM non-return valve Vertical type of approved as per specification and direction of E/I. Horizontal non-return valve 32 mm dia weight not less than 600 gm .

Supplying materials and labours for constructing inspaction chamber of designation class 75B bricks size 750mm deep, 600X450mm internal dimention having 250mm wall thickness in cement morter (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 36kg.) alongwith earth work in excavation and 80 mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler -75mm

Coupler- 110mm

Bend 87.5° - 75 mm bend

Bend 87.5° - 110 mm bend

Shoe (Plain) - 75 mm Shoe

Shoe (Plain) - 110 mm Shoe

Single tee without door - 75x75x75 mm

Single tee without door - 110x110x110 mm

Non Schedule Item Providing and laying bitumen (asphalt) shingles roofing of approved make (TECHNONICOL or equivalent) over 18 mm thick cement sheet base using the torch-on method. The work includes cleaning and preparing the surface, applying one coat of approved bitumen primer, and laying one layer of APP-modified bitumen underlay membrane torched to the primed surface with 100 mm side and 150 mm end overlaps. Bitumen shingles shall be fixed in approved shade and pattern by heating (torch applied to the underlay membrane only) and pressed firmly to achieve full adhesion. All valleys, ridges, edges, and roof penetrations shall be sealed with bitumen mastic/sealant to ensure complete watertightness. Hip and ridge shingles, edge flashings, and other necessary fittings shall be installed as per manufacturer’s specifications. The rate shall include the cost of all materials, primer, underlay membrane, shingles, adhesives, sealants, labour, tools, equipment, scaffolding, and all incidental works, complete in all respects as per manufacturer’s technical data and direction of Engineer-in-Charge.

Providing and fixing uPVC gutter of 300 mm height with a top opening of 300 mm, having a minimum wall thickness of 2.5 mm, including all necessary fittings such as end caps, outlets, bends, clamps, brackets, sealants, and supports. The gutter shall be jointed using manufacturer’s recommended solvent cement and securely fixed to the structure with proper alignment and slope for smooth drainage. The rate includes cost of all materials, accessories, labour, scaffolding, and all incidental works, complete in all respects as per manufacturer’s specification and direction of Engineer-in-Charge.

Design, Engineering, Patterning, Fabrication, Supplying & installation in position of Walkway Conical Tensile Membrane Fabric Structure as per detail specification with all civil works (A) Providing, Designing, Engineering, Patterning, Fabrication, Supplying and installation of Architectural Membrane, Assembling, Hoisting, Erecting and placing in position MS built-up section/Tubular structure frame work using MS plates of variable thickness confirming to IS 2062 (Grade YST 240) and Tubular structure made from Steel hollow sections, ISI marked confirming IS 1161/4923 (Grade YST 240) in the profile and including necessary foundation bolts & base plates. Fabrication of structural elements shall be done using SAW/MAW/MIG welding process. In the profile shape as per drawings with special plate connector, pinion joints, plates, hollow sections etc. with cleaning the surface and including Preparation of detailed Architectural Membraneation and erection drawings of Structural steel work from design, transportation from Architectural Membrane yard, cutting, threading, machining. leads and lifts up to all heights, tools and plants and necessary scaffolding etc. required for all operations involved to make structure of Architectural Membrane shade. All members shall be hot finished welded type tubes (B) Providing and applying the complete structure with anti-corrosive protection coating using Poly Uthnerian Paint over single coat of Epoxy primer in required DFT (dense film thickness). The work is to be executed as per technical specification(C) Flexible composite Cover Supplying, Providing, Fabricating, assembling and erection of pre stressed Tensile Membrane Fabric structure with SERGE FERRARI/MEHLER/SIOEN or equivalent Type I fabric with a Tio, front side primer, multilayered Nanopolymered flouorinated lacquer, multi-composed PVDF lacquer on both sides, low wick treated, protected against microbial and fungal attack, UV-protected system roofing as per the manufacture's specification and as per approved drawing. The sheeting material shall have HT polyester yarns 1100 dtex, weight should be 700 g/m² (EN ISO 2286-2), White coloured 0.6 mm thick fabric, minimum Tensile strength should be 3000 N/5cm in wrap and 3000 N/5cm in weft directions (DIN EN ISO 1421), minimum Tear strength should be 300 N in wrap and 300 N in weft (DIN 53363), the membrane should be with a minimum of 15 years warranty from the manufacturer and life expectancy 20 years etc. over steel frames with all fittings and fixtures such as Galvanized MS Membrane / End Plate, Shackles, Rigging Screws, Turnbuckles, swedge, fork, keder rods & galvanized MS strands/cables with stainless steel end terminals complete as per Drawing/detail and as per technical specifications. This should also include shop drawing, patterning, forming, cutting, fabrication, hot weld stitch of fabric, Transport to the site, assembling and installation with GI Cables, hardware, EPDM gasket and required accessories for necessary Tensioning Material includ ng lifts up to all heights as approved shape as per c'rawing. Flexible Composite Cover shall be cut and manufactured with High frequency PVC Welding Machine.

Supply and installation of wall panelling using 19 mm thick, waterproof Century Marine Ply conforming to IS:710 standards and ISI certification, with termite resistance. The panelling shall be fixed over 2"x1" aluminium pipes and finished with an approved shade of high-quality Suede type 1.25 mm laminate. Teak bead trimming and layer panel work, including PU finish in varying sizes as specified in the building requirements and as directed by the Engineer-in-Charge, are to be provided. All laminates and plywood (710 Marine Grade) must be of Green, Century, Archid, or equivalent brand, subject to the engineer’s approval

Providing and fixing French moulding made of WPC in various approved sizes and shapes (ranging from 20 mm to 50 mm), fixed over 19 mm thick waterproof, termite-proof HDHMR board (ISI marked) supported on 50 mm × 25 mm (2" × 1") aluminium ‘T’ or ‘L’ section framework. The surface shall be finished with 12 mm thick gypsum board, properly jointed and levelled with acrylic wall putty, and finished with two or more coats of Asian Paints Royal Aspira (or equivalent) in desired shade and finish. The rate includes supply of all materials, mouldings, framework, adhesives, fixing accessories, putty, paint, labour, scaffolding, and all incidental works complete in all respects as per manufacturer’s specifications and direction of Engineer-in-Charge.

Providing and fixing wall panelling at all heights made of 18 mm thick HDHMR board (High Density High Moisture Resistant board) of approved make, fixed over aluminium framework of 50 mm × 25 mm rectangular hollow sections spaced not more than 600 mm c/c both ways, securely fastened to the base wall using suitable anchor fasteners and brackets. The exposed surface shall be finished with high-quality PU (Polyurethane) paint in approved shade and texture, applied in multiple coats including primer, putty, surface preparation, sanding, and final polishing to obtain a smooth, uniform and durable finish. The rate includes cost of all materials, adhesives, consumables, fittings, scaffolding, labour, and all incidental charges to complete the work in all respects as per manufacturer’s specification and direction of Engineer-in-Charge. (Approved make of HDHMR board: Action Tesa / Greenpanel / Century or equivalent.)

Providing and fixing WPC Louvers in 19 mm thick plywood backing with aluminium channel frame (38×25 mm), fixed using adhesive and necessary hardware. The work includes supply, installation, and complete framework, with one side finished in WPC material and service coating on the reverse side. The rate shall include cost of materials, scaffolding, labour, taxes, and all incidental charges complete as per building specification and direction of Engineer-in-charge

Providing and fixing wall panelling at all heights comprising 19 mm thick BWP (Boiling Water Proof) Marine Grade Plywood conforming to IS:710, ISI marked and termite resistant, fixed over a framework of 50 mm × 25 mm (2"x1") aluminium rectangular hollow sections spaced not more than 600 mm c/c both ways, securely anchored to the parent wall using suitable fasteners and brackets. The plywood surface shall be finished with approved shade of natural veneer texture, duly sanded and applied with multi-coat Polyurethane (PU) polish, including surface preparation, sealing, and final buffing to achieve a smooth, durable finish. The rate includes cost of all materials, adhesives, fixing hardware, labour, scaffolding, wastage, and all incidental charges to complete the work in all respects as per manufacturer’s specification and direction of Engineer-in-Charge. (Approved make of Plywood/Veneer/Laminate: Greenply / Century / Archid or equivalent as approved by Engineer-in-Charge.)

Providing and fixing wooden door shutter (laminated finish, 40–50 mm thick as per need ): Providing and fixing door shutter of overall thickness 45 to 50 mm, made from a well-seasoned hardwood frame, both sides pressed with BWP Grade plywood (IS:710) and finished with 1.25 mm thick waterproof decorative laminate of approved shade and make (Green / Century / Archid or equivalent). All edges shall be finished with matching hardwood lipping. The shutter shall be fitted with approved branded hardware and fancy fittings, including mortise lock, latch, stainless steel butt hinges, handles, tower bolts, door stopper, and hydraulic door closer, complete with all screws and accessories. The rate includes all materials, labour, adhesives, finishing, and incidental works as per specification and direction of Engineer-in-Charge.

Providing and fixing panelling on existing door and window chowkhats: Providing and fixing 12 mm thick waterproof and termite-proof Marine Plywood (IS:710, ISI marked) over existing door and window chowkhats, finished with 1.25 mm thick suede-finish decorative laminate of approved shade and make (Green / Century / Archid or equivalent). The plywood shall be fixed with synthetic resin adhesive and screws, and all exposed edges shall be properly lipped and finished. The rate includes all materials, labour, adhesives, and incidental works complete as per specification and direction of the Engineer-in-Charge.

Providing and fixing SPC (Stone Plastic Composite) flooring of approved make, design and shade, having wear layer thickness not less than 0.3 mm and overall thickness 6 mm, laid over smooth and levelled base using manufacturer’s recommended adhesive or click-lock system. The flooring shall be moisture resistant, termite proof and suitable for heavy-duty indoor use. The rate includes cost of all materials, labour, surface preparation, cutting, fitting at edges, joints, and finishing complete as per manufacturer’s specification and direction of Engineer-in-Charge

Supplying and fixing roller blinds of approved branded make with blackout fabric made of high-quality polyester base, acrylic polymer coated and flame-retardant, complete with aluminium top roller, side chain mechanism, brackets, and all necessary accessories. The blinds shall be installed in the specified locations as per manufacturer’s specifications and direction of the Engineer-in-Charge. The rate includes supply, fixing, labour, and all incidental charges complete in all respects.

Providing and fixing 450 mm deep book-shelved cupboard made out of 25 mm thick HDHMR board for sides, top, bottom, and shelves, and 38 mm thick HDHMR board for back partition, all as per approved design and drawing. The cupboard shall have approximately three-fourth open racks and balance portion with shutters. The open shelves shall be finished with approved shade PU polish on all sides. The shuttered portion shall be finished with three coats of polyurethane lacquer paint of approved make and shade over surfaces prepared with waterproof 2K polyester putty, primer coat, and finished with matt/textured lacquer finish. The rate includes cost of all materials, labour, fittings, fixtures such as handles, catchers, screws, etc., complete in all respects as per drawing, specification and direction of Engineer-in-Charge. Payment shall be made for the front elevation area only

Providing and fixing 600mm wide quartz top running counter with 600mm deep X 900mm deep below storage made in 19mm thick plywood frame work as per the detailed drawings The counter top shall have 20mm thick Quartz Stone and of approved shade. The counter shall have below storage unit with intermediate adjustable shelves and shutters made in 19mm thick plywood necessary ply backing, finished of approved shade. The counter to have granite splash band over fixed with cement mortar and the Cement paste with edge detail as per the detailed drawing. The storage unit shall have in combination of open shelves & closed storage unit with intermediate shelves & shutters made in 19mm thick plywood necessary ply backing, finished in 1.25 mm Royal Touch laminate HD Seriesof approved shade. (Make of Laminate and Plywood (710 Marine Grade) Green/Century/Archid or equivalent as per direction of engineer in Charge)

Providing and fixing full height storage units with luggage rack below of 600 mm deep made in 38 mm thick plywood edge finish and finished in 1.25 mm Royal Touch laminate HD Series. The internal shelves & drawers shall be made in 19 mm thick plywood finished in laminate of approved shade with matching PVC edge lipping as per the detailed drawing. All the exposed external and internal plywood surfaces shall also be finished with laminate of approved shade per the detailed drawings. This also includes necessary hardware like sliding channels, handles, hinges, tower bolts/ball catches, locks etc. as per the manufacturer’s specification adhering to the design intent drawings. This also includes 75 mm high laminate finished skirting as per the detailed drawing. (Make of Laminate and Plywood (710 Marine Grade) Green/Century/Archid or equivalent as per direction of engineer in Charge)

Providing and fixing modular kitchen pantry with upper cabinet, made of 38 mm thick HDHMR board for sides, top, bottom, and 19 mm thick HDHMR board for back partition and shelves as per approved design and drawing. The countertop shall be of quartz stone slab of approved make and shade, edge moulding, polishing and 100 mm high backsplash. All exposed surfaces shall be finished with PU polish and shuttered portions three coats of polyurethane lacquer paint of approved make and shade over surfaces prepared with waterproof 2K polyester putty, primer coat and finished with matt or textured lacquer finish. Unexposed surface finish with 1 mm branded Laminate The rate includes all materials, labour, fittings and fixtures such as soft-close hinges, drawer channels handles, catchers and accessories, complete as per specifications and direction of Engineer-in-Charge. Payment shall be made for the front elevation area only

Providing and fixing terracotta jali partition made of natural clay square edge blocks of size 8" × 8" × 2.5", in antique and modern mixed design, fixed in a MS frame of required size and pattern as per approved architectural design. The jali units shall be set in cement mortar or adhesive as required, with proper alignment, spacing, and finishing to achieve a uniform decorative appearance. The rate includes supply of all materials, fabrication and fixing of MS frame (including necessary supports, welding, priming, and painting), installation of terracotta blocks, labour, adhesives, scaffolding, and all incidental works, complete in all respects as per drawing, building specification, and direction of the Engineer-in-Charge.

Cleaning the concrete surface thoroughly to remove dust, grease, loose paint, and laitance using mechanical means and compressed air, including all labour, tools, and tackles. Repairing surface defects and damaged concrete using polymer-modified repair mortar prepared with SBR latex (Sika Latex or equivalent) after applying a bonding coat of SBR-cement slurry. After proper curing and drying, apply one coat of Davco K10 PU Plus (or equivalent PU waterproof coating) and loosely lay a 120-micron non-woven geo-textile membrane over the coated surface. Provide and lay a minimum 75 mm thick cement concrete screed (1:2:4, M15) admixed with SBR waterproofing compound, laid to proper slopes towards drain outlets. Screed shall be cast in 2 m × 2 m panels with 10 mm × 10 mm grooves sealed with Sika Polysulphide sealant. Where required, provide an additional 50 mm thick concrete layer to maintain slope. Finally, apply two coats of Davco K10 So Acryl (or equivalent acrylic elastomeric waterproof coating) to achieve a seamless waterproof film of minimum 1 mm dry film thickness (DFT). All materials and workmanship shall comply with manufacturer’s technical data sheets. The system shall be cured as per manufacturer’s recommendation and subjected to a 24-hour ponding test to ensure complete watertightness before the final finish is applied. The rate includes all materials, surface preparation, coatings, membranes, admixtures, labour, curing, testing, tools, equipment, and incidental works, complete in all respects as per specification and direction of the Engineer-in-Charge.

Add 18 % GST

Add 1% Labour Cess

Please Enable Macros to View BoQ information