Loading
Loading…
Loading…
Tender Value
₹1.5 Cr
EMD Value
₹2.2 L
Closing Date
24 Mar 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
DEN IV
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Technical Eligibility Criteria: (a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender.Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity.(b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract.
Defination of Similar Work :- Any type of track work.
7 conditions · 1 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tenderer may please note that offers received without requisite/mandatory documents as mentioned above, will be considered as invalid tender and for which contractor shall have no claim on Railway.
The tenderer shall visit the site of work and acquaint himself/themselves with the conditions of work viz. approach roads and accessibility, availability of materials, electric power, water for work and drinking purposes, site for labour camps, stores, godowns, extent of lead/lift in work, availability of skilled and unskilled labour etc. that may be encountered in the course of execution of work. In short, he/they should familiarize himself/themselves fully with the all the conditions of the work site & all the financial implications due to the above conditions is deemed to be understood and taken care of while bidding the offer.
Improvement of yard and attention to turnout in the section of ADEN/JHI.
121-2025-26-W-IV
121-2025-26-W-IV
Open
Works - General
6 Months
Delhi, Delhi
₹0
₹2.2 L
24 Mar 2026
26 Feb 2026
10 Mar 2026
71 items across 1 schedule · ₹1,44,88,926.43 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | For Casual/Scattered Rail Renewal work | RM | 2000.00 | 40.73 | 81,460 |
| 2 | For Casual/Scattered Rail Renewal work | RM | 2000.00 | 43.13 | 86,260 |
| 3 | For 1.00m long fishplates | Joint | 1000.00 | 118.51 | 1,18,510 |
| 4 | Lubrication of Elastic Rail Clips on PSC sleepers with contractor's grease, conforming to Railway's specifications, labour etc. complete as per procedure prescribed in latest edition of IRPWM. | ERC | 50000.00 | 3.34 | 1,67,000 |
| 5 | Hole of dia. 26.5mm and above | Each | 1000.00 | 259.11 | 2,59,110 |
| 6 | Rail section of 52Kg and above | Each | 500.00 | 110.37 | 55,185 |
| 7 | 1 in 8½ Turnouts | Set | 5.00 | 20,686.67 | 1,03,433.35 |
| 8 | 1 in 12 Turnouts | Set | 5.00 | 27,369.47 | 1,36,847.35 |
| 9 | 1 in 16 Turnouts | Set | 1.00 | 30,735.45 | 30,735.45 |
| 10 | 1 in 8½ Points & Crossing | Set | 5.00 | 15,402.34 | 77,011.7 |
| 11 | 1 in 12 Points & Crossing | Set | 5.00 | 20,972.17 | 1,04,860.85 |
| 12 | 1 in 16 Points & Crossing | Set | 1.00 | 24,171.18 | 24,171.18 |
| 13 | Sleepers up to 2.85 m length | Each | 100.00 | 699.07 | 69,907 |
| 14 | Sleepers of length more than 2.85 m and up to 4.20 m | Each | 50.00 | 963.98 | 48,199 |
| 15 | 1 in 8½ Turnout | Set | 5.00 | 4,368.33 | 21,841.65 |
| 16 | 1 in 12 Turnout | Set | 30.00 | 4,785.57 | 1,43,567.1 |
| 17 | 1 in 8½ Switch Assembly | Set | 10.00 | 15,555.98 | 1,55,559.8 |
| 18 | 1 in 12 Switch Assembly | Set | 30.00 | 17,319.11 | 5,19,573.3 |
| 19 | 1 in 8.5 Turnouts | Set | 10.00 | 2,346.82 | 23,468.2 |
| 20 | 1 in 12 Turnout | Set | 40.00 | 3,970.76 | 1,58,830.4 |
| 21 | For 1 in 12 Turnouts (Sleeper No 1 to 25 and 5 approach sleepers) | Set | 50.00 | 1,925.36 | 96,268 |
| 22 | For 1 in 8.5 Turnouts & Derailing switches (Sleeper No 1 to 22 and 5 approach sleepers) | Set | 10.00 | 1,540.29 | 15,402.9 |
| 23 | For 1 in 12 Lead portion (Sleeper Nos 26 to 64 & 74 to 83 and 8 approach sleepers) : | Set | 50.00 | 4,147.72 | 2,07,386 |
| 24 | For 1 in 8.5 Turnouts (Sleeper No 23 to 42&59 to 54 and 8 approach sleepers) | Set | 10.00 | 3,318.18 | 33,181.8 |
| 25 | For 1 in 12 Turnouts (Sleeper No 65 to 73 ) | Set | 50.00 | 1,395.54 | 69,777 |
| 26 | For 1 in 8.5 Turnouts (Sleeper No 43 to 48) | Set | 10.00 | 1,116.43 | 11,164.3 |
| 27 | Renewal of corroded slide chairs duly removing the old slide chairs by heating using contractors gas and equipments or by any approved methods and inserting Railways new slide chairs and plate screws including crossing of tracks, leading all required materials to site, stacking all released materials, with all contractor's tools, consumables, labour, lead, lift and incidental charges etc complete as directed by the Engineer in charge. Note: 1. All the fittings will be supplied at nearest SSE/Stores. 2. In case of damage of PSC sleeper, penalty at the rate of 25% of the current cost of sleeper shall be levied. | Each | 700.00 | 413.37 | 2,89,359 |
| 28 | Turnout sleepers of length up to 2.85 m | Each | 400.00 | 157.77 | 63,108 |
| 29 | Sleepers of length more than 2.85 m and up to 4.20 m | Each | 400.00 | 189.33 | 75,732 |
| 30 | Sleepers of length more than 4.20 m | Each | 400.00 | 205.1 | 82,040 |
| 31 | Depth of 300 mm below bottom of sleeper of Plain Track | TRM | 1000.00 | 523.72 | 5,23,720 |
| 32 | Depth of 300 mm below bottom of sleeper for Turnouts | TRM | 1000.00 | 837.95 | 8,37,950 |
| 33 | Depth of 300 mm below bottom of sleeper - For Plain Track : | TRM | 1000.00 | 668.57 | 6,68,570 |
| 34 | Depth of 300 mm below bottom of sleeper for Turnouts | TRM | 1000.00 | 1,069.71 | 10,69,710 |
| 35 | Extra to item nos. from 081011 to 081018 and from 081021 to 081028 for disposal of muck at a distance beyond 50m for every additional lead of 50 metres or part thereof up to 500 metres for 1 TRM in station yard / cutting. | Each | 4000.00 | 6.38 | 25,520 |
| 36 | Extra to item nos. from 081011 to 081018 and from 081021 to 081028 for disposal of muck for additional lift of 1 metre or part thereof beyond 3 metre lift in case of disposal of muck from track f o r 1 TRM in station yard / cutting. | Each | 4000.00 | 13.29 | 53,160 |
| 37 | Lifting and packing for regrading the existing PSC sleeper track to required height / level in stages not exceeding 75mm or part thereof at a time, providing permissible ramp for the track, insertion of moorum / sand / stone ballast uniformly under the existing track and placing the same to safe approved gradient, gauge, cushion including levelling and one round of through packing to allow train movement at restricted speed of 30 kmph for a specified length with all leads & lifts and fixing, marking, painting rail level pegs at every 30m interval. Note: Lifting of track shall be done in stages as per procedure prescribed in latest edition of IRPWM to get the proposed final level as per approved working profile, as directed by Engineer in-charge. | TRM | 2000.00 | 205.4 | 4,10,800 |
| 38 | Extra for additional lift over 75mm for every 50mm lift or part thereof up to 275mm for item nos. 083010 for each TRM. | TRM | 5000.00 | 31.9 | 1,59,500 |
| 39 | Boxing and profiling of ballast as per procedure prescribed in latest edition of IRPWM including cess dressing on both sides of track. The work will include removing excess ballast from track and putting the same in crib and shoulder by leading to a maximum of 50m including crossing of track, deweeding on ballast section etc and as directed by Engineer-In charge. | TRM | 10000.00 | 30.19 | 3,01,900 |
| 40 | Under Traffic Block Conditions: | cum | 2000.00 | 60.27 | 1,20,540 |
| 41 | Under Conditions not requiring Traffic Block: | cum | 2000.00 | 45.7 | 91,400 |
| 42 | For PSC sleeper Track with Sleeper Density of 1540 Sleepers/Km or more | TRM | 2000.00 | 119.75 | 2,39,500 |
| 43 | For PSC sleeper Track with Sleeper Density of less than 1540 Sleepers/Km | TRM | 2000.00 | 103.19 | 2,06,380 |
| 44 | For PSC Sleeper | TRM | 10000.00 | 102.65 | 10,26,500 |
| 45 | For PSC sleeper Track with Sleeper Density of 1540 sleepers/Km or more | TRM | 2000.00 | 204.34 | 4,08,680 |
| 46 | For PSC sleeper Track with Sleeper Density less than 1540 sleepers/Km | TRM | 2000.00 | 155.01 | 3,10,020 |
| 47 | One Gang comprising of 20 physically fit labours plus 1 Mate. Note: In case, contractor provides less no. of Labour/Mate, payment will be deducted for each such labour @ 10% of the accepted item rate. | Gang Day | 30.00 | 17,726.34 | 5,31,790.2 |
| 48 | Removing weeds & bushes in ballast section and cess up to 3.95m from centre line of track in mid section & station yard, as specified by Engineer in-charge including disposal of branches, bushes outside cess/yard. | TRM | 40000.00 | 17.1 | 6,84,000 |
| 49 | For 60 Kg Rails | TRM | 2000.00 | 67.83 | 1,35,660 |
| 50 | For 52 Kg Rails | TRM | 2000.00 | 60.27 | 1,20,540 |
| 51 | 60 Kg - 110/90 UTS - Outside Track | Each | 500.00 | 210.19 | 1,05,095 |
| 52 | 60 Kg - 110/90 UTS - On Running Line | Each | 500.00 | 269.03 | 1,34,515 |
| 53 | Sleeper Spacing, Re-spacing / Squaring of sleeper by Hydraulic Sleeper Spacer with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in-charge. Hydraulic Sleeper Spacer shall be as per RDSO's Specification No. TM/SM/17, dated 31.03.1992. | Each | 7000.00 | 83.43 | 5,84,010 |
| 54 | Drilling of holes (vertically) of required size into concrete sleeper in-situ for fixing guard rails and check rails on concrete sleeper track at specified locations by concrete sleeper drilling machine with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in- charge as per RDSO's Specification. | Each | 500.00 | 108.37 | 54,185 |
| 55 | Extraction of jammed ERC by Heavy Duty Hydraulic Extractor with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in- charge. Heavy Duty Hydraulic Extractor for jammed ERCs (10 Ton capacity) shall be used as per RDSO's Specification No. TM/SM/6, dated 8.05.1991. | Each | 1200.00 | 40.34 | 48,408 |
| 56 | For lead up to 500 metre. | MT | 100.00 | 439.62 | 43,962 |
| 57 | For lead beyond 500 metre and up to 1 Km. | MT | 100.00 | 567.69 | 56,769 |
| 58 | Extra to Items no. 171032 for lead beyond 1 Km for every subsequent Km or part thereof and up to 10 Km | MT | 100.00 | 68.07 | 6,807 |
| 59 | Opening of level crossing up to required width from centre line of track for replacement of sleepers by digging of pucca road surface up to bottom of sleeper, removing of ballast, muck etc., screening of ballast & stacking the same near level crossing and disposing of all debris, replacing the required sleeper duly packing the sleeper to make fit for normal traffic and closing of LC surface with screened ballast to original level by proper ramming and consolidation to smooth motarable surface as directed by engineer in-charge. | Sqm | 500.00 | 421.8 | 2,10,900 |
| 60 | Dismantling existing check rail of Level Crossing, blocks, bolts & nuts and stacking these in a countable manner near LC, free from any infringements as directed by Engineer in-charge. | RM | 50.00 | 207.47 | 10,373.5 |
| 61 | Fabrication including cutting, bending/machining and fixing of check rails of all rail sections over PSC Sleepers as per Railway's approved drawings & specifications for level crossings / trolley paths/inspection lines in yards duly cutting rail flanges, wherever required to correct alignment and level, drilling of holes with machine in check rails and fixing to Running rail and sleepers with all Railway's fittings, e.g. rail screws / grip expansion bolts, brackets, packing pieces, bolts, washers etc including grinding of brackets if required, fixing of Railway's wooden blocks at flare ends duly cutting and plaining, crossing of tracks and as directed by the engineer in-charge Note: 1. Drilling of holes in PSC Sleeper and fixing of dowels shall be paid under relevant item. 2. Required P.Way materials will be supplied at SSE/P.Way stores. | TRM | 20.00 | 1,237.52 | 24,750.4 |
| 62 | Drilling of 25mm to 40mm dia. holes in PSC sleepers with suitable rotary hammer / drilling machine at indicated location for fixing of guard rails on bridges & its approaches as per approved drawing and fixing of contractor's HDPE dowels and adhesive of approved quality to Drawing no. RDSO/T-3002, procured from RDSO's approved sources with contractor's materials and consumable. | Each | 200.00 | 166.07 | 33,214 |
| 63 | Boards with single post | Each | 400.00 | 226.8 | 90,720 |
| 64 | Boards with two posts | Each | 20.00 | 260.75 | 5,215 |
| 65 | Fabricating of check rails of 52Kg and 90R sections for providing to curves by cutting web of rail horizontally by gas, grinding for smoothening the cut edge and drilling of parabolic shaped holes to the web of check rails as per drawing and specification and as per directions of engineer in-charge with all contractor's labour, tools and materials complete. Note: 1. Rails shall be supplied by Railways 2.The both ends of head of check rails are to bent/cut as per drawing. 3. The released rail scrap shall be stacked neatly with in a lead of 500m. 4.Drilling of holes shall be paid under relevant item. | RM | 400.00 | 280.09 | 1,12,036 |
| 66 | Dismantling Check Rail on curves on track of all rail sections, duly removing fish plates and bolts including removing chairs from sleepers, leading and stacking released materials away from track clear of infringements, complete and as directed. | RM | 400.00 | 73.56 | 29,424 |
| 67 | Fixing of check rails on curves on track of all rail sections as per drawing and to correct alignment and level with Railways fastenings including leading of rails and fittings, crossing of tracks, greasing of plate screws with approved grease etc., as per drawing and directions of Engineer in charge with all contractors labour, tools, plants, machinery, consumables etc., complete. Note: Required P.Way fittings will be supplied at SSE/P.Way stores. | RM | 100.00 | 76.97 | 7,697 |
| 68 | Supplying and spraying in specified proportion Weedicide Chemical, capable to kill entire weed on track / cess / embankment with all labour, material, tools & plants etc. complete job in all respect. Scientific name of the chemical is Isopropylamine Salt of Glyphosate, in which active ingredient is Glyphosate (41%), colour is light amber to brownish, very low in toxicity and has favourable environmental characteristics. It will be ensured that no weed growth occurs up to six months period, otherwise re-spraying shall be done by the contractor free of cost. | Sqm | 200000.00 | 0.84 | 1,68,000 |
| 69 | JCB Backhoe Loaders 3DX Plus or similar with minimum 1.10 cum bucket capacity | Hour | 500.00 | 858.69 | 4,29,345 |
| 70 | Hydra or similar tyre mounted Pick-n-Carry crane of 12T capacity for misc. works of handling of material | Hour | 1000.00 | 878.02 | 8,78,020 |
| 71 | Tractor with Trolley for local transportation or other misc. works. | Hour | 1000.00 | 200.69 | 2,00,690 |
| Schedule total | ₹1,44,88,926.43 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC-2022withCSupto10.pdf
ATTACHMENT
StandardTenderDocument2022R5.pdf Standard Tender Document 2022
ATTACHMENT
StandardTenderDocument2022R5.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .