Development of parks for person with special abilities near House no. 1440 sector 46 under Municipal Corporation Gurugram. Recall

Drinking Water cooler 100-Ltr.capicity 2 nos. outlet push Toti provision with 60-LPH per hour R O , complete in all respect as per satisfaction of engineer in charge.

25 MM EPDM Rubber Sport flooring granules including installation, transportation and GST charges complete in all respect to full satisfaction of Engineer-in-charge.

Specially Abled People Arm andTai Chi Wheel Fitness Apparatus Providing and fixing the following outdoor fitness equipment’s designed for minimum 100 kg user Weight confirming to the required standard for safety and quality as per DIN/ASTM /CPSC/European standard / BIS The equipment shall be confirming to the specification as below:- a) All the equipment shall be Third Party Quality certified as per the specified standard. b) Nuts and Bolts- Stainless steel 316 and lock-nut c) Material – Galvanized steel Pipe cleaned by stand-blasting then coated with phosphate solution and finished with electro-static powder coating or other similar available material meeting the required standard d) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostatic powder coating technique To process the pipe surface e) Column the mild steel pipe column footing plate screw with a pull-burst, the surface rust acid decreasing cleaning phosphate rust. After a special process, throwing sand imported plastic powder with a double surface household- level spraying layer, electrostatic spray, high-temperature plastic 200 degree baking powder smooth surface UV resistant or as specified by the manufacture’s specification f) Seat and plastic LLDPE/HDPE metal with any protection / composite material with any protection infiltration of anti- static de-colorization element passing, strength, smooth surface, Security assurance weather resistant etc. g) UV-fully resistant Platforms- High strength punching plate with special process dealing with wavy surface microscopy, safe and beautiful non-slip resistance Fasteners – stainless steel screw to be used and at the contact point with the columns- rubbers pads to be used , screw top cover with a plastic cap, to enhance its security The installation of the equipment’s shall be carried out on cement concrete foundation of minimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in- charge of mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size ) The cost for equipment shall include the required foundation bolts of 18 mm dia and of required shape and length as per sample approved by Engineer-in-charge however the cost for earthm work and CC shall be paid for separately .The rates Quoted for the put door fitness specifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approved make. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I) “A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres).All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I) “A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment must be made and confirms with the approved standards certified by and certificates are mandatory requires in the name of both Tenders act as bidder and manufacturer. 1. IS 17801 2. ISO 18001 3. ISO 27001:2013 4. ISO 50001:2018 5. ISO 13485:2016 6. ISO 45001:2018 7. ISO 14001:2015 8. ISO 9001:2015 9. ISO 14001:2004 10. ISO 9001:2008 11. EN 14904 12. EN-1176-1-2017 13. EN 16630:2015 14. EN 16630 15. EN 957 16. EN 9100:2016 17. EN 11630:2017 18. GS 19. DIN 18032.2 20. DIN 79000-2012 21. CE Certificate 22. CE 11993 23. OHSAS 18001:2017 24. SLBR 62 25. BIFMA 26. GMP 27. RoHS The equipment must accompained with Test report for Quality, Safety, Durability and Proper Functioning of Equipment must mandatory requires Test report in the name of both Tenderer act as bidder and manufacturer. 1. Test Report of SS Nut and Bolts 2. Test Report of LLDPE Base Caps for Open Gym 3. Test Report of Powder Coating Pipe 4. Test Report of SKF Bearing No. 6007-2Z 5. Test Report of FRP/Plastic (Fiber Pad) 6. Test Report of Welding Pipe (Robotic MIG Welding) 7. Test Report of MEK Solvent 8. Test Report of Neutrul Salt Spray Test 9. Test Report of Breaking Load of Welding Pipe 10. Test Report of GI Pipe 100 mm NB 11. Test Report of GI Pipe 80 mm NB 12. Test Report of GI Pipe 50 mm NB 13. Test Report of GI Pipe 32 mm NB 14. Test Report of GI Pipe 25 mm NB

Specially Abled People Lat Pull Down and Tai Chi Wheel Fitness Apparatus The handles hanging from the curved bar at the top are for lat pull-downs, which work the back and arm muscles. Lat shoulder Wheels: The two yellow discs are likely shoulder wheels, used for improving shoulder mobility and flexibility.8. ISO 9001:2015 9. ISO 14001:2004 10. ISO 9001:2008 11. EN 14904 12. EN-1176-1-2017 13. EN 16630:2015 14. EN 16630 15. EN 957 16. EN 9100:2016 17. EN 11630:2017 18. GS 19. DIN 18032.2 20. DIN 79000-2012 21. CE Certificate 22. CE 11993 23. OHSAS 18001:2017 24. SLBR 62 25. BIFMA 26. GMP 27. RoHS The equipment must accompained with Test report for Quality, Safety, Durability and Proper Functioning of Equipment must mandatory requires Test report in the name of both Tenderer act as bidder and manufacturer. 1. Test Report of SS Nut and Bolts 2. Test Report of LLDPE Base Caps for Open Gym 3. Test Report of Powder Coating Pipe 4. Test Report of SKF Bearing No. 6007-2Z 5. Test Report of FRP/Plastic (Fiber Pad) 6. Test Report of Welding Pipe (Robotic MIG Welding) 7. Test Report of MEK Solvent 8. Test Report of Neutrul Salt Spray Test 9. Test Report of Breaking Load of Welding Pipe 10. Test Report of GI Pipe 100 mm NB 11. Test Report of GI Pipe 80 mm NB 12. Test Report of GI Pipe 50 mm NB 13. Test Report of GI Pipe 32 mm NB 14. Test Report of GI Pipe 25 mm NB a) All the equipment shall be Third Party Quality certified as per the specified standard. b) Nuts and Bolts- Stainless steel 316 and lock-nut c) Material – Galvanized steel Pipe cleaned by stand-blasting then coated with phosphate solution and finished with electro-static powder coating or other similar available material meeting the required standard d) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostatic powder coating technique To process the pipe surface e) Column the mild steel pipe column footing plate screw with a pull-burst, the surface rust acid decreasing cleaning phosphate rust. After a special process, throwing sand imported plastic powder with a double surface household- level spraying layer, electrostatic spray, high-temperature plastic 200 degree baking powder smooth surface UV resistant or as specified by the manufacture’s specification f) Seat and plastic LLDPE/HDPE metal with any protection / composite material with any protection infiltration of anti-static de-colorization element passing, strength, smooth surface, Security assurance weather resistant etc. g) UV-fully resistant specifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approved make. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I) “A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I) “A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment must be made and confirms with the approved standards certified by and certificates are mandatory requires in the name of both Tenders act as bidder and manufacturer. 1. IS 17801 2. ISO 18001 3. ISO 27001:2013 4. ISO 50001:2018 5. ISO 13485:2016 6. ISO 45001:2018 7. ISO 14001:2015

Specially Abled People Outdoor Chest Press Fitness Apparatus Providing and fixing the following outdoor fitness equipment’s designed for minimum 100 kg user Weight confirming to the required standard for safety and quality as per DIN/ASTM /CPSC/European standard / BIS The equipment shall be confirming to the specification as below:- a) All the equipment shall be Third Party Quality certified as per the specified standard. b) Nuts and Bolts- Stainless steel 316 and lock-nut c) Material – Galvanized steel Pipe cleaned by stand-blasting then coated with phosphate solution and finished with electro-static powder coating or other similar available material meeting the required standard d) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostatic powder coating technique To process the pipe surface e) Column the mild steel pipe column footing plate screw with a pull-burst, the surface rust acid decreasing cleaning phosphate rust. After a special process, throwing sand imported plastic powder with a double surface household- level spraying layer, electrostatic spray, high-temperature plastic 200 degree baking powder smooth surface UV resistant or as specified by the manufacture’s specification f) Seat and plastic LLDPE/HDPE metal with any protection / composite material with any protection infiltration of anti- static de-colorization element passing, strength, smooth surface, Security assurance weather resistant etc. g) UV-fully resistant Platforms- High strength punching plate with special process dealing with wavy surface microscopy, safe and beautiful non-slip resistance Fasteners – stainless steel screw to be used and at the contact point with the columns- rubbers pads to be used , screw top cover with a plastic cap, to enhance its security The installation of the equipment’s shall be carried out on cement concrete foundation of minimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in-charge of mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size ) The cost for equipment shall include the required foundation bolts of 18 mm dia and of required shape and length as per sample approved by Engineer-in-charge however the cost for earth work and CC shall be paid for separately .The rates Quoted for the put door fitness equipment’s shall be inclusive of 1st Year comprehensive maintenance specifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approved make. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I) “A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I) “A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment must be made and confirms with the approved standards certified by and certificates are mandatory requires in the name of both Tenders act as bidder and manufacturer. 1. IS 17801 2. ISO 18001 3. ISO 27001:2013 4. ISO 50001:2018 5. ISO 13485:2016 6. ISO 45001:2018 7. ISO 14001:2015 8. ISO 9001:2015 9. ISO 14001:2004 10. ISO 9001:2008 11. EN 14904 12. EN-1176-1-2017 13. EN 16630:2015 14. EN 16630 15. EN 957 16. EN 9100:2016 17. EN 11630:2017 18. GS 19. DIN 18032.2 20. DIN 79000-2012 21. CE Certificate 22. CE 11993 23. OHSAS 18001:2017 24. SLBR 62 25. BIFMA 26. GMP 27. RoHS The equipment must accompained with Test report for Quality, Safety, Durability and Proper Functioning of Equipment must mandatory requires Test report in the name of both Tenderer act as bidder and manufacturer. 1. Test Report of SS Nut and Bolts 2. Test Report of LLDPE Base Caps for Open Gym 3. Test Report of Powder Coating Pipe 4. Test Report of SKF Bearing No. 6007-2Z 5. Test Report of FRP/Plastic (Fiber Pad) 6. Test Report of Welding Pipe (Robotic MIG Welding) 7. Test Report of MEK Solvent 8. Test Report of Neutrul Salt Spray Test 9. Test Report of Breaking Load of Welding Pipe 10. Test Report of GI Pipe 100 mm NB 11. Test Report of GI Pipe 80 mm NB 12. Test Report of GI Pipe 50 mm NB 13. Test Report of GI Pipe 32 mm NB 14. Test Report of GI Pipe 25 mm NB

Specially Abled People Arm extension Fitness Apparatus Providing and fixing the following outdoor fitness equipment’s designed for minimum 100 kg user Weight confirming to the required standard for safety and quality as per DIN/ASTM /CPSC/European standard / BIS The equipment shall be confirming to the specification as below:- a) All the equipment shall be Third Party Quality certified as per the specified standard. b) Nuts and Bolts- Stainless steel 316 and lock-nut c) Material – Galvanized steel Pipe cleaned by stand-blasting then coated with phosphate solution and finished with electro-static powder coating or other similar available material meeting the required standard d) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostatic powder coating technique To process the pipe surface e) Column the mild steel pipe column footing plate screw with a pull-burst, the surface rust acid decreasing cleaning phosphate rust. After a special process, throwing sand imported plastic powder with a double surface household- level spraying layer, electrostatic spray, high-temperature plastic 200 degree baking powder smooth surface UV resistant or as specified by the manufacture’s specification f) Seat and plastic LLDPE/HDPE metal with any protection / composite material with any protection infiltration of anti-static de-colorization element passing, strength, smooth surface, Security assurance weather resistant etc. g) UV-fully resistant Platforms- High strength punching plate with special process dealing with wavy surface microscopy, safe and beautiful non-slip resistance Fasteners – stainless steel screw to be used and at the contact point with the columns- rubbers pads to be used , screw top cover with a plastic cap, to enhance its security The installation of the equipment’s shall be carried out on cement concrete foundation of minimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in-charge of mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size ) The cost for equipment shall include the required foundation bolts of 18 mm dia and of required shape and length as per sample approved by Engineer-in-charge however the cost for earth work and CC shall be paid for separately .The rates Quoted for the put door fitness equipment’s shall be inclusive of 1st Year comprehensive maintenance specifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approved make. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I) “A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I) “A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment must be made and confirms with the approved standards certified by and certificates are mandatory requires in the name of both Tenders act as bidder and manufacturer. 1. IS 17801 2. ISO 18001 3. ISO 27001:2013 4. ISO 50001:2018 5. ISO 13485:2016 6. ISO 45001:2018 7. ISO 14001:2015 8. ISO 9001:2015 9. ISO 14001:2004 10. ISO 9001:2008 11. EN 14904 12. EN-1176-1-2017 13. EN 16630:2015 14. EN 16630 15. EN 957 16. EN 9100:2016 17. EN 11630:2017 18. GS 19. DIN 18032.2 20. DIN 79000-2012 21. CE Certificate 22. CE 11993 23. OHSAS 18001:2017 24. SLBR 62 25. BIFMA 26. GMP 27. RoHS The equipment must accompained with Test report for Quality, Safety, Durability and Proper Functioning of Equipment must mandatory requires Test report in the name of both Tenderer act as bidder and manufacturer. 1. Test Report of SS Nut and Bolts 2. Test Report of LLDPE Base Caps for Open Gym 3. Test Report of Powder Coating Pipe 4. Test Report of SKF Bearing No. 6007-2Z 5. Test Report of FRP/Plastic (Fiber Pad) 6. Test Report of Welding Pipe (Robotic MIG Welding) 7. Test Report of MEK Solvent 8. Test Report of Neutrul Salt Spray Test 9. Test Report of Breaking Load of Welding Pipe 10. Test Report of GI Pipe 100 mm NB 11. Test Report of GI Pipe 80 mm NB 12. Test Report of GI Pipe 50 mm NB 13. Test Report of GI Pipe 32 mm NB 14. Test Report of GI Pipe 25 mm NB

Specially Abled People Pull Chair with Cycle Combination Fitness Apparatus A pull chair, also known as a pull-wheelchair, combines the functionality of a standard wheelchair with a cycling feature, allowing the user to propel themselves using their hands on the rear wheels. Cycle-handicapped wheelchairs, on the other hand, are typically powered by hand cranks. a) All the equipment shall be Third Party Quality certified as per the specified standard. b) Nuts and Bolts- Stainless steel 316 and lock-nut c) Material – Galvanized steel Pipe cleaned by stand-blasting then coated with phosphate solution and finished with electro-static powder coating or other similar available material meeting the required standard d) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostatic powder coating technique To process the pipe surface e) Column the mild steel pipe column footing plate screw with a pull-burst, the surface rust acid decreasing cleaning phosphate rust. After a special process, throwing sand imported plastic powder with a double surface household- level spraying layer, electrostatic spray, high-temperature plastic 200 degree baking powder smooth surface UV resistant or as specified by the manufacture’s specification f) Seat and plastic LLDPE/HDPE metal with any protection / composite material with any protection infiltration of anti-static de-colorization element passing, strength, smooth surface, Security assurance weather resistant etc. g) UV-fully resistant specifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approved make. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I) “A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I) “A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment must be made and confirms with the approved standards certified by and certificates are mandatory requires in the name of both Tenders act as bidder and manufacturer. 1. IS 17801 2. ISO 18001 3. ISO 27001:2013 4. ISO 50001:2018 5. ISO 13485:2016 6. ISO 45001:2018 7. ISO 14001:2015 8. ISO 9001:2015 9. ISO 14001:2004 10. ISO 9001:2008 11. EN 14904 12. EN-1176-1-2017 13. EN 16630:2015 14. EN 16630 15. EN 957 16. EN 9100:2016 17. EN 11630:2017 18. GS 19. DIN 18032.2 20. DIN 79000-2012 21. CE Certificate 22. CE 11993 23. OHSAS 18001:2017 24. SLBR 62 25. BIFMA 26. GMP 27. RoHS The equipment must accompained with Test report for Quality, Safety, Durability and Proper Functioning of Equipment must mandatory requires Test report in the name of both Tenderer act as bidder and manufacturer. 1. Test Report of SS Nut and Bolts 2. Test Report of LLDPE Base Caps for Open Gym 3. Test Report of Powder Coating Pipe 4. Test Report of SKF Bearing No. 6007-2Z 5. Test Report of FRP/Plastic (Fiber Pad) 6. Test Report of Welding Pipe (Robotic MIG Welding) 7. Test Report of MEK Solvent 8. Test Report of Neutrul Salt Spray Test 9. Test Report of Breaking Load of Welding Pipe 10. Test Report of GI Pipe 100 mm NB 11. Test Report of GI Pipe 80 mm NB 12. Test Report of GI Pipe 50 mm NB 13. Test Report of GI Pipe 32 mm NB 14. Test Report of GI Pipe 25 mm NB

Specially Abled People Wave Balance Fitness Apparatus 1. Size: 2386 x 136 x 1795mm 2. Constructed with weather-resistant powder-coated steel and anti-slip wave- shaped foot platform. 3. Platform length: 1800 mm: width: 400 mm: height variation simulates gentle wave motion. 4. Includes dual side handrails (height: 900 mm) with 42 mm diameter for stability and grip. 5. Supports up to 150 kg user weight: fixed to ground with anti-rust anchor bolts. 6. Enhances balance, coordination, and lower limb control for senior users in outdoor settings. 7. All the equipment shall be Third Party Quality certified as per the specified standard. 8. Nuts and Bolts- Stainless steel 316 and lock-nut 9. Material – Galvanized steel Pipe cleaned by stand-blasting then coated with phosphate solution and finished with electro-static powder coating or other similar available material meeting the required standard 10. Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostatic powder coating technique To process the pipe surface 11. Column the mild steel pipe column footing plate screw with a pull-burst, the surface rust acid decreasing cleaning phosphate rust. After a special process, throwing sand imported plastic powder with a double surface household- level spraying layer, electrostatic spray, high-temperature plastic 200 degree baking powder smooth surface UV resistant or as specified by the manufacture’s specification 12. Seat and plastic LLDPE/HDPE metal with any protection / composite material with any protection infiltration of anti- static de-colorization element passing, strength, smooth surface, Security assurance weather resistant etc. 13. UV-fully resistant Platforms- High strength punching plate with special process dealing with wavy surface microscopy, safe and beautiful non-slip resistance Fasteners – stainless steel screw to be used and at the contact point with the columns- rubbers pads to be used , screw top cover with a plastic cap, to enhance its security The installation of the equipment’s shall be carried out on cement concrete foundation of minimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in- charge of mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size ) The cost for equipment shall include the required foundation bolts of 18 mm dia and of required shape and length as per sample approved by Engineer-in-charge however the cost for earthm work and CC shall be paid for separately .The rates Quoted for the put door fitness specifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approved make. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I) “A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I) “A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment must be made and confirms with the approved standards certified by and certificates are mandatory requires in the name of both Tenders act as bidder and manufacturer. 1. IS 17801 2. ISO 18001 3. ISO 27001:2013 4. ISO 50001:2018 5. ISO 13485:2016 6. ISO 45001:2018 7. ISO 14001:20158. ISO 9001:2015 9. ISO 14001:2004 10. ISO 9001:2008 11. EN 14904 12. EN-1176-1-2017 13. EN 16630:2015 14. EN 16630 15. EN 957 16. EN 9100:2016 17. EN 11630:2017 18. GS 19. DIN 18032.2 20. DIN 79000-2012 21. CE Certificate 22. CE 11993 23. OHSAS 18001:2017 24. SLBR 62 25. BIFMA 26. GMP 27. RoHS The equipment must accompained with Test report for Quality, Safety, Durability and Proper Functioning of Equipment must mandatory requires Test report in the name of both Tenderer act as bidder and manufacturer. 1. Test Report of SS Nut and Bolts 2. Test Report of LLDPE Base Caps for Open Gym 3. Test Report of Powder Coating Pipe 4. Test Report of SKF Bearing No. 6007-2Z 5. Test Report of FRP/Plastic (Fiber Pad) 6. Test Report of Welding Pipe (Robotic MIG Welding) 7. Test Report of MEK Solvent 8. Test Report of Neutrul Salt Spray Test 9. Test Report of Breaking Load of Welding Pipe 10. Test Report of GI Pipe 100 mm NB 11. Test Report of GI Pipe 80 mm NB 12. Test Report of GI Pipe 50 mm NB 13. Test Report of GI Pipe 32 mm NB 14. Test Report of GI Pipe 25 mm N

Specially Abled People Outdoor Fitness Ladder 1. Constructed from powder-coated stainless steel with anti-corrosive finish for outdoor durability. 2. Ladder length: 2000 mm: rung spacing: 150 mm with 30 mm diameter rungs for secure grip. 3. Rungs coated with non-slip material to ensure safe climbing and grip. 4. Mounted on a sturdy base with ground anchors for stability and safety. 5. Designed to improve upper body strength, coordination, and mobility for specially abled users. 6. All the equipment shall be Third Party Quality certified as per the specified standard. 7. Nuts and Bolts- Stainless steel 316 and lock-nut 8. Material – Galvanized steel Pipe cleaned by stand-blasting then coated with phosphate solution and finished with electro-static powder coating or other similar available material meeting the required standard 9. Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostatic powder coating technique To process the pipe surface 10. Column the mild steel pipe column footing plate screw with a pull-burst, the surface rust acid decreasing cleaning phosphate rust. After a special process, throwing sand imported plastic powder with a double surface household- level spraying layer, electrostatic spray, high-temperature plastic 200 degree baking powder smooth surface UV resistant or as specified by the manufacture’s specification 11. Seat and plastic LLDPE/HDPE metal with any protection / composite material with any protection infiltration of anti- static de-colorization element passing, strength, smooth surface, Security assurance weather resistant etc. 12. UV-fully resistant Platforms- High strength punching plate with special process dealing with wavy surface microscopy, safe and beautiful non-slip resistance Fasteners – stainless steel screw to be used and at the contact point with the columns- rubbers pads to be used , screw top cover with a plastic cap, to enhance its security The installation of the equipment’s shall be carried out on cement concrete foundation of minimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in- charge of mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size ) The cost for equipment shall include the required foundation bolts of 18 mm dia and of required shape and length as per sample approved by Engineer-in-charge however the cost for earthm work and CC shall be paid for separately .The rates Quoted for the put door fitness specifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approved make. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I) “A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I) “A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment must be made and confirms with the approved standards certified by and certificates are mandatory requires in the name of both Tenders act as bidder and manufacturer. 1. IS 17801 2. ISO 18001 3. ISO 27001:2013 4. ISO 50001:2018 5. ISO 13485:2016 6. ISO 45001:2018 7. ISO 14001:2015 8. ISO 9001:2015 9. ISO 14001:2004 10. ISO 9001:2008 11. EN 14904 12. EN-1176-1-2017 13. EN 16630:2015 14. EN 16630 15. EN 957 16. EN 9100:2016