PROVISION OF SPECIAL REPAIRS TO CERTAIN BLDGS IN AGE B/R I SUB DIVISION UNDER GE (NORTH ) BIKANERER

Amount

Dismantling of existing false ceiling of AC sheet etc

Dismantling Asbestos cement Corrugated sheets in roof covering including ridges .

Dismantling timber scantling 40 sq cm and over in section, in any position complete.

Taking down cement plaster on brick or conc surfaces including racking out joints hacking for key, scrubbing down with water etc.

Demolition of cement concrete in ground floor and pavings n.exc 15cm thick below or above ground level including tiles and similar works complete all as specified and removing the same to dumping yard as directed by E-in-Charge

Demolition of brick or stone masonary including all necessary arches, pillars, quions etc built in cement mortar.

Dismantling water tanks complete of capacity n exc 500 ltrs.

Taking up or down steel water tubing 15mm dia and connection ,incl cleaning for refixing

Taking up or down steel water tubing 20mm dia and connection ,incl cleaning for refixing

Dismantling of cast iron or PVC , jointed incement mortar pipes up to 100 mm bore in any position

Taking down chowkhat or frames exc 1.50 Sqm n.exc 4 Sqm (without taking down shutters from the frames)

Do but n.exc 1.50 Sqm

Taking down door shutter of any desc exc 1 sqm but not exc 2 sqm and refixing in the same opening.

M&L cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foudation, filling, sub base and mass concrete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

Dismantling structural steel work as in trusses nexc 10.00 mtr span .

M&L for brick work with fly ash bricks (old sized bricks ) straight or curved on plan exc 6 m mean radious built in cement mortar 1:6.

Brickwork with flyash bricks, (old sized bricks ) straight or curved on plan to any radius in half brick thick walls built in

M&L Mild steel work in tubular trussess/ purlins incl spl shaped washer etc. using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240. complete all as specified and directed by Engineer-In-Charge.

M&L Mild steel framed brackets of angles or tees with web and flanges cut to shape, drilled and countershunk for screw, including bending and welding angles, as necessary, guser plate, riveting, etc. n exc. 10 kg brackets, confirming to Fe. 290 Gde -E-165 (Brackets over 10 kg each to be measured under structural steel ) complete all as specified and as directed by Engineer-In-Charge.

S&F Mild steel bolts.exc. 5 cm length not exc. 10 cm length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fittied with washers and one hexagonal or square nut 11 to 15 mm neck dia complete all as specified and as directed by engineer-in-charge.

Erection and fixing only steel work in roof trusses including special shape washers et. Complete.

M&L for pre painted galvalume aluminium zinc cozting GI based corrugated steel Sheet high rib profile tile pattern color coated 0.5 mm thick of 550 Mpa Tensile strength sheets as in roof covering and fixed as per manufacturers instruction (design as app by Engg in charge complete all as spfd )

M&L Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for Rendering 10+5 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified.

M&L for 15mm thick rendering on brick or concrete surfaces in cm 1:6 finished even and smooth w/o using extra cement

M&L for rendering 5 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:3 and finished fair and even without using extra cement.

M&L for 40-50mm thick sand stone slab not exc 2mtr in length, punched dressed self faced set and pointed in CM 1:4 as in sun-shades, chajjas, shelves, cills landings, cover stone as directed

M&L Composite cement ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel (Make-everest ramco or eql.) designer ceiling pre finished conforming to IS 14862 type B cateogory three incl GI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with suspenter and adjuster .)

M&L for 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as floor finishes complete all as specified and as directed by Engineer-in-charge.

Supply only 3mm thick glass 38mm wide glass dividing stripps laid in design as directed by Eng-in-charge

M&L 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection laid in bays complete including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified

S&F 20-25 mm Thick single piece machine cut kota stone slab in flooring laid and jointed with gry cement slurry Mixed with pigment to match the shade of the slab incl rubbing and mirror polishing 15mm thick screed bed in CM1:6 complete incl roughing the surface all as spd and as directed by Engineer-in-charge.

Cutting to existing kota stone flooring including minor repairs and polishing complete

S&F 125 x 60mm pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges lock strike plate etc complete as specified including a coat of shop coat zinc chrome primer.

M&L PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in filling in pressed steel frames complete all as specified and as directed by Engineer-in-Charge

S&F 35mm thick Factorymade second class hard wood plain framed pannelled shutter (two panels and double shutter) with lock rail and pannel or 9mm BWP comerical ply or 12mm venered particle board with comerical face venering on both faces. The size of rail and style as per IS-1003 part kilin seasoned

S&F 2nd class hardwood 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass guage, etc. (without sash bars), edges of framing plain, chamfered or rounded. Fitted with cut and mitred beads for securing glass,etc. sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24(a); supplied and fitted to chowkhats complete all as specified and as directed by Engineer-in-charge.

S&F Butt hinges, medium weight, cold rolled mild steel --100-- mm size complete.

S&F mild steel barrel tower bolt, stove enamelled black with bright bolt of 150 mm complete.

S&F mild steel sliding door bolts plate type stove enameled black with bright bolt not less than 12 mm dia with and incl. a minimum of 6 bolts and nuts four on bolt plate and two on staple plate of 300 mm long complete all as specified and as directed by Engineer-In-Charge.

S&F MS pressed handle oval type stove enamel block with bright bolt of 150 mm. complete.

S&F mild steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by engineer-in-charge.

S&F steel window/ ventilator (box type) factory made glaged and guaged with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBZ/888R & 889 Sheet 1 to 4. ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

S&F 3 mm Sheeet glas ordinary quality and glazing with oil putty in square n exc. 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

M&L Galvanised stain less steel wire cloth 0.56 mm nominal dia of wire anfd averqagae width of aperature 1.18mm and fixed with tinned tracks, or galvanised wire spaples.

Do but fixed as in repairs .

M&L for 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes.

M&L for 15mm thick rendering on fair faces of brick works in cement mortar 1:4 finished even and fair for receiving tiles as in dado.

M&L for cement concrete rich colored chequered tiles machine pressed with imported pigment finish (mirror/rough cast) of size 300mmx300mmx(25 mm to 40 mm ) thick set and jointed with neat cement slurry

M&L For pcc type B1(1:2:4) using 20 mm graded cushed stone agg as in coping to path ,edging ,kerb stone,benching and the like incl form work

M&L for PCC type C1 1:3:6 using 20mm graded crushed stone aggregate as in surface channel and drain beads including all necessary form work..

M/L for Non Skid ceramic tiles (size of each tile exc 0.06sqm and n exc 0.11 sqm) 7mm thick laid and jointed with cement slurry (in portions) and pointed with coloured cement to match in floor.Colour approved by the Engr in Charge.

S&F galzed ceramic colored tiles as in vertical surfaces 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry (in portions) and pointed with white or colored cement to match

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved.

S&F factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the steel frame at site as per specification.

S&F Butt hinges extruded alumonium alloy with galvanised mild steel hinges pin anodisedand fixed ,type B-21 of 100mm.

Aluminium anodised barrel tower bolt of extruded section of 150mm

Aluminium handles cast type anodised of 150mm

S&F Rotational moulded polythene water storage tank (cylindrical vertical with closed top)hoisted and fixed in position of 500 ltrs

M&L for Dismantling Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and refixing in position all as specified in SSR Part-I of capacity 500 litres including all accessories, all as specified.

Ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 20mm Make : Prayag or equivalent.

M&L vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete lived in repairs and making good to floor complete.

S&F Viterous china wash down water closet pan pan (pedestal pattern ), white (excluding flushing cistern , flush pipe.(Make: CERA,Perryware,Hindware)

S&F pvc white seat cover incl all necessary hinges

S&F PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete as in repairs .

Fixing only Flushing cistern after repairing the old one retrieved from repair work with and including washers , syphon kit etc .

S & F in repair brass chromium plated bib cock short body Fancy type with capstan screwed down for iron pipe 15 mm bore complete all as specified & directed.

S&F in repair 32/40 mm dia PVC waste pipe for WHB/sink complete all as specified .(Min weight 45 to 60 gms .

S&F tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor bore of pipe 15 mm .

S&F tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor bore of pipe 20 mm .

Angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F Pvc connection 15mm size with PTMT nuts of length 450mm.

S&F PVC(SWR)single socketed in any length with rubber ring joint 110mm laid in trenches

S&F PVC(SWR)single socketed in any length with rubber ring joint 75 mm fixed to walls incl clamps .

S&F PVC SWR branch piece single equal or unequal 110mm

S&F PVC(SWR) bends any radius 110mm.

S&F PVC(SWR) bends any radius 75 mm.

S&F PVC(SWR) reducer socket bends any radius 100 mm.

S&F PVC(SWR)Cowl 75 mm.

M&L for preparation of new plastered and unplastered surfaces of walls by applying a 3 mm thick thin layer of Birla white putty to give uniform surface applying coat of oil bound distamper on walls old decorated surfaces of desired finish as app by Eng-in-charge in any position

M&L Complete removal of existing treatment of walls and applying two coats of oil bound distemper over a thin coat of wall care putty complete all as specified and as directed by Engineer-in-Charge.

M&L for prep of new plastered and unplastered surfaces of walls and applying two coat of Cement Base Paint on walls oover a priming paint as per manufacturer's instructions in any position

M&L Complete removal of existing treatment of walls and applying two coats of cement based paint complete all as specified and as directed by Engineer-in-Charge.

M&L Preparing surface of steel of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer

M&L for preparation of steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint all as specified.

Do but one coat on old decorated surfaces.

M&L for two coats of synthetic enamel paint on new wooden surfaces incl prep over a coat of pink primmer.

M&L for preparing newly plastered surfaces of walls and applying two coats of white wash.

Do but one coat on old decorated surfaces.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash.

M&L for one coat of synthetic enamelled paint on old decorated wooden surfaces including preperation

Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and as directed by the Engr-in-Charge.

Taking down of unserviceable DBs/switch fuses/changeover in sheet steel enclosure complete with MCBs/Fuse/grips any capacity and removing from site and making good disturbed surface of wall, floor etc. Taking after disconnecting all cable complete all as specified and as directed by the Engr-in-Charge.

Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid PVC concealed conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No. 96 here-in-before but socket point on the same board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No.96 here-in-before but socket point on the independent board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No. 96 here-in-before but cable 2.5 Sqmm for 15 Amps switch socket outlet on independent board complete as specifed as directed by Engineer - In - Charge

M&L Socket outlet 2 in 1, 3 pin, 5A

S&F Switch piano flush type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge Make : Anchor / Cona / havells

S&F Switch socket combination 5 in 1, 5/ 16A, flush type fixed on laminated sheet top cover (laminated sheet cover is included in point wiring).

S&F Ceiling rose PVC/poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : Make : Anchor / Cona / havells

S&F Lamp holder insulated body with back plate for conduit/casing capping fittings complete all as specified and as directed by Engineer-in-Charge. make Anchor / Cona / havells

S&F Ceiling fan regulator electronic type, 230 Volt, 150 Watt with 5 step of control including making holes in laminated bakelite sheet cover and connection complete all as specified and as directed by Engineer-in-Charge. Make LEADER/SSK.

S&F Decorative ultra slim linear LED lightening fixture, energy efficent 18/20 Watt complete all as specified and directed by engineer-in-charge.

S&F Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 240 volts with 200 Amps rated bus bar,SPN 8 ways, complete all as specified and as directed by Engineer-in-Charge.

MCB single pole, 240 volts of rating 6-32 Amps, breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge

MCB suitable for 6 to 32 Amps, 240 Volt AC supply single pole and neutral with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by mean of GI wire 4 mm dia by means of bolts, nuts check nuts and washers of GI or steel and connecting to earthing test point, main switch board, testing on completion including GI pipe 20 mm dia light grade for watering and bringing the same upto 30 cm above normal ground level with plug at top including pipe fittings etc complete and GI pipe 15 mm dia light grade for the protection of GI wire from earth pit to earth point complete including necessary excavation and earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50 m all as specified as shown in electrical plate No 3 SSR Part-I.

Supply and laying in replacement cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 mtr in depth for route of cable and getting out complete all as specified and as directed by the Engr-in-charge.

Returning, filling in soft/loose soil including spreading, leveling watering and well ramming, in layers not exc 25 cm complete all as specified and as directed by the Engr-in-charge.

Removing of surplus soil to a distance not exc. 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and directed by Engr-in-charge.

Protection to cable with one layer of bricks laid flat butting to each other in such a way that the length of the bricks is at right angle to the central axis of the cable using old size sub-class 'B' bricks complete all as specified and directed by Engr-in-charge.

Local tibba dry sand cushioning for protection of cable complete all as specified and as directed by Engineer-in-charge. Note Local approved tibba dry sand after removal of vegetations, grass and other deleterious substances shall be used for sand cushioning.

M & L GI tubing light grade for protection of cables with pole/ in ground of size 40mm dia complete all as specified and as directed by Engineer-in-Charge.

Supply & fix LED bulk head ,09W / 10 W, IP65 diacast aluminium housing powder coating finished complete all as specified and directed by Engineer-in-charge.

Taking down celing fan ,ceiling cable end, dismanting blades and removing fans and blades to store complete all as specified and as directed by Engineer-in-Charge.

Hanging only ceiling fan and connecting up with provn of 3 core flexible cable of size 1.5 sq mm complete all as specified and as directed by Engineer-in-Charge.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 6 sq. mm nominal cross section in service connections

SHREE GURU NANAK CONSTRUCTION COMPANY

M/S BUDHRAM BISHNOI

SUBHAM ENTERPRISES

JAMUNA CONSTRUCTION AND GENERAL ORDER SUPPLIER

M/S ASHRAFI CONSTRUCTION CO