PROVISION OF HARDSTANDING AND ALLIED WORKS NEAR BLDG NO NP39 AT HQ NORTHERN COMMAND AND ADITIONAL ALTERATION OF SURGERY ROOM IN BLDG NO P05 AT CMDC NC UNDER GE SOUTH UDHAMPUR

Amount

Surface excavation in soft/loose soil, not exceeding 30cm deep and averaging 15cm deep and getting out of any type of soil complete all as specified and as directed

Excavation over areas, not exc 1.5 mtr deep in any type of soil and getting out complete all as specified and as directed

M&L for returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25cm thick all as specified and directed.

Removing excavated soil material to a distance n exc 50 m and deposited where directed at a level not exc 1.5m above the base as in soil all as specified and directed

Taking down cement plaster and raking out joints, hacking for key,scrubbing down with water built in cement mortar any description complete all as specified and as directed

Taking down frames with shutters (without taking off shutters from the frame ) area not exc 1.5 Sqm each incl iron mongry complete all as directed.

Taking down frames with shutters (without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4 Sqm each incl iron mongry complete all as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Demolition of cement concrete any description and any position not otherwise specifically provided complete all as specified.

M&L for RCC M-25 (Design mix) in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and as directed.

M&L for RCC M-25 (20mm graded aggregate) as in slab type Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed

M&L PCC1:2:4 using B1 (20mm graded aggregate) for coping, corner of roof and similar work complete all as sepcified and directed.

M&L for 75 mm thick PCC 1:4:8 type D2 using 40mm graded aggregate as in sub base of floor etc complete all as specified and as directed.

M&L for 75 mm thick PCC type CI 1:3:6 using 20mm graded crushed stone aggregate as in plinth protection laid in alternate pannels finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 75 mm thick PCC type C-2 1:3:6 , using 40mm graded crushed stone aggregate as in sub base for receiving floor finishes finished even and fair complete all specified and as directed.

Machine pressed (factory made) precast plain cement concrete 1:2:4 type B-1(20mm graded crushed stone aggregate), kerb stone & the like of size 300mm x 300mm x 100mm thick or of size as approved by GE, with plain fair faces including chamfers, weathering etc, embedding in position/laid in trenches on edges of roads, including excavation in any type of soil, setting in cement mortar (1:4) returning filling and removal of surplus soil/debris to a distance n.exc. 50m from the starting point, complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L brick work with sub class B bricks, straight or curved on plan exc 6 m mean radium built in CM 1:6 all as specified and as directed.

M&L half brick wall with sub class B bricks, straight or curved on plan exc 6 m mean radium built in CM 1:4 all as specified and as directed.

M&L hardcore of broken bricks gauge exc 63mm but n.exc 100mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rolled /rammed to true surfaces complete all as specified and as directed

M&L walling of random rubble uncoursed well bonded bedded and solidly hearted built in cement mortar (1:6) complete all as specified and as directed

M&L for raised pointing to random rubble or polygolal rubble uncoursed of brought upto courses in CM 1:4 complete all as specified and as directed

Rendering 15mm thick in CM 1:4 on fair faces of brick/concrete finished even and smooth without using extra cement complete all as specified and as directed

Rendering 10mm thick in CM 1:6 on fair faces of brick/concrete finished even and smooth without using extra cement complete all as specified and as directed

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pilasters, buttresses, etc.; vertical or to batter on rough finished surfaces of concrete complete all as specified and as directed.

M&L 1mm thick wall care putty on wall complete all as specified and as directed

M&L for applying two coat of plastic emulsion paint to new plastered surfaces at brick masonry/concrete surface over cm 10 width or girth including a cot of primer complete all as specified and as directed

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed

M & L for Vitrified tiles light Shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed

M&L for vitrified ceramic tiles(Double charge glossy finish), area of each tile exc 0.42sqm but not exc 1.00 Sqm, 10mm thick (square or rectangular) of superior quality as in floor surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Ditto as per item No 30 above but in vertical surfaces such as skirting/dado and including 10mm thick rendering as back coating etc complete all as specified and as directed

M & L for Glazed Coloured Ceramic tiles in vertical surface 300x450x7mm or 300x600x7mm thick laid over 10 mm thick screed bed in CM 1:4, set and joint in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed

M&L 18-20 mm thick granite stone slab as in shelves / vertical surfaces /platforms set and jointed in neat cement slurry,pointed in colored cement to match the shade incl rubbing of moulding etc complete all as specified and as directed.

S&F Vitrified Dura stone tiles of size not exc 0.36 Sqm of 15mm thick as in floors and over & including 15mm thick screed bed or bedding layer in cement mortar 1:4, including jointed with neat cement slurry and pointed in coloured cement to match the surface of tiles, complete all as specified and directed.

10-12 mm thick gypsum boards seemess false ceiling including sunk or raised moulding or cop design as approved, moisture resistant, including GI hanging wires & frames with intermediate, perimeter channel ceiling channel, along nuts and bolts connecting plates gypsum boards, dry wall screws soffits cleats, ceiling section, rawel plugs fixtures and screws and applying two coats of emulsion paint over a coat primer on exposed surface complete all as specified and directed by Engr-in-Charge. Note : (a) Design of ceiling board as approved by Engr-in-Charge. (b) GI grid/hanging system shall be of the same make as of false ceiling manufacturer

S&F TMT bars upto 10mm dia and over, cut to length, bent to shape required,including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and similar work, n exc 200mm thick (horizontal or sloping) complete all as specified and as directed.

M & L form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specified and as directed.

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) (A) Area not exceeding 2.00 sqm each

Supply and fixing factory made uPVC white/coloured fixed glazed window/ventilator/Partition walls made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately).

M & L for sheet glass 5.5mm thick of one side view, ordinary quality and glazing with beads fixed with metal panel pins, EPDM washers or connected accessories exc 0.5 sqm in each pane complete all as specified and as directed

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F 4 mm dia galvanised steel wire 50 mm x 50 mm mesh made up in to matresses or cages etc complete all as specified and as directed.

M&L for preparation of newly steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube suppling and fixing in opening as per specification & drawing complete all as specified and as directed.

S & F factory made solid PVC moulded door shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, fixing in frame at site as per specification & drawing complete all as specified and as directed.

S&F mild steel cold rolled butt hinges medium weight 100 mm long complete all as specified and as directed.

S & F 200 mm long brassh barrel tower bolt of extruded section complete all as specified and as directed.

S&F 150 mm length brass handles cast type polished bright complete all as specified and as directed.

S & F 300 mm long mild steel sliding door bolt with hasp staple (bolt type ) and fixing clips of sheets ,cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and as directed.

S&F stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18mm complete all as specified and as directed.

M&L for Modular Kitchen cupboard/almirah in required size at site made out 18 mm thick one side decorative lamination sheet/sunmica consisting of carcass 18/20 mm thick PVC sheet & provn of shutters made out of 18mm thick one side decoartive laminated PVC sheet/Sumica all required brackets SS screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edbes shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish, necessary drawer, openable shelve with frame work complete as per make and specification mention as per drawing with locking arragement approved by Engr-in-Charge complete all as specified and as directed.

S&F PVC steel catcher of superior quality all as specified and directed by Engr in charge

Supply only Stainless steel basket (plain), SS plate basket(11-13 division), SS partition basket, SS Cutlery basket, SS grid basket of size as per manufacturer/ as directed by Engr in Charge made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make. Make: Life style Cat part No WA/POB/15204 or equivalent approved

S & F Hetich softcloser hinges of stainless steel premium quality complete all as specified and as directed.

Fancy type Brass handles 100mm size fixed with screws, complete all as specified and as directed.

S & F 30 mm width of flap Continous (Piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed.

S&F 20mm dia mild steel powder coated fancy type tubular curtain rail with brackets and end bulb as per reqirement. all as directed.

15mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs complete all as specified and as directed.

20mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs complete all as specified and as directed.

S&F Sinks with draining board made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x460mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.

S&F PVC connection 15 mm size with PTMT nuts 600mm long, fixed in repairs, complete all as specified and as directed.

S&F countertop vitreous chinaware wash hand basin (WHB) white size 550mm x 400mm complete including provision of pair of mild steel angle iron brackets of suitable size duly painted, 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc complete. Make : Jaquar Make :KUS-WHT-35601 or its equivalent in Hindware/Cera/Parryware

S&F 5 mm thick looking mirror of required size, fixed on walls with dash fasteners and chromium plated screws purposefully made to fix the glass by drilling hole in the glass complete all as directed.

S & F 15 mm dia WHB mixer chromium plated screwed down high pressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specifie and as directed. Make - Jaquar Cat No KUP-35011BPM or equivalent in Hindware

S & F 15 mm dia Sink mixer chromium plated screwed down highpressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specified Make - Jaquar Cat No LYR-38165 or equivalent in Hindware/Parryware .

S&F 15 mm bore Bib tap complete all as specified and directed. Make : Jaquar Cat Part No CON 107KN and equvalent in CERA/Hindware/Parryware.

S&F 15 mm dia Angle valves/stop cock, fancy type and chromium plated screwed down highpressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specified and as directed. Make - Jaquar Cat No KUP-35053PM or equivalent in Hindware & Parryware

S&F 600 mm long brass chromium plated towel rail fancy type complete all as specified and directed. Make : Jaquar Cat Part No ACN-1111NM and equivalent in CERA/Hindware/Parryware.

S&F Towel rack complete all as specified and directed. Make : Jaquar Cat Part No ACN 1181FN and equivalent in CERA/Hindware/Parryware.

S&F Soap dish complete all as specified and directed. Make : Jaquar Cat Part No ACN 1131N and equivalent in CERA/Hindware/Parryware.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

S&F 110 mm PVC (SWR) pipes single socket in any lenth with rubber ring joints fixed to wall complete all as specified and as directed.

S&F 110 mm PVC (SWR) bends any redius with access door complete all as specified and as directed.

PVC (SWR) gully trap 125/110 mm, settting and jointing with solvent cement in repair complete all as specified and as directed.

M & L for hand packing (any thickness) of broken stone or boulder at back of walls over arches etc and raising (or lowering) to the required level all as specified and directed

M&L for plain cement concrete1:2:4 type B-2 using 40 mm graded stone aggregate as in channels and drains, foundation and similar work etc complete all as specified and as directed.

S & F 110mm dia PVC (SWR) pipes single stack in any length as in weepholes of retaining wall all as specified and directed

M&L for Rolling and consolidating formation surfaces in cutting with exc 8 tonne and n exc 12 tonne power roller complete all as specified and as directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power) complete including fitting such as switch, sockets, ceiling rose, pendants socket,fan regulators any type, rectangular board ,light fittings,terminal boxes etc removing materials for taking credit and making good disturbed surfaces of walls floors and ceiling complete all as specified and as directed.

Taking down main switches, distribution boards and cut outs etc. of any type and capacity along with the existing boards and removing the same from site and making good the disturbed surface/portion of walls complete all as specified and directed By Engr-in-Charge.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLSH copper conductor cables (multistranded) PVC insulated and unsheathed in and including PVC concealed conduit pipe as per site requirement (size not less than 20mm dia), medium grade with Modular sunken boxes & PVC/metal back plate for mounting modular type switches, sockets & regulators etc with cover plate modular type including supplying and laying PVC insulated and stranded unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire connected to earth dolly including cutting of chases in wall /ceiling etc and making good the disturbed surfaces match to existing with cement mortar and putty white /colour wash complete all as directed . Make: Havells/ Finolex/ Polycab.

All as per item no 85 above but cable 2.5 sqmm FRLSH for one 3/5 pin 6 Amp socket outlet point on an independent board.

All as per item no 85 above but cable 2.5 sqmm FRLSH for one 3/5 pin 6 Amp socket outlet point on the same board with other switch.

All as per item no 85 above but for one 3/6 pin 16 amps socket outlet point on an independent board with cables of size 2.50 sqmm.

All as per item no 85 above but an independent board with cables of size 4.0sqmm.

S&F for modular switch 6 Amps single pole one way 230 V, 50 Hz, AC , with outer cover complete all as specified and directed by Engr In charge. Make:Legrand/Havells crabtree/L &T

S&F for modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with outer/inner cover complete all as specified and directed by Engr In charge. Make:Legrand/Havells crabtree/L &T

S&F for modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with outer cover complete all as specified and directed by Engr In charge. Make:Legrand/Havells crabtree/L &T

S&F for modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush type with outer/inner cover complete all as specified and directed by Engr In charge. Make:Legrand/Havell crabtree/L &T

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed.

S&F electronic step type fan regulator 100 watt 230 volts 50Hz 2 module type complete all as specified and directed. Make: Havells Crabtree/ Legrand/ Indoasian.

S&F in replacement sheet metal enclosure for MCB DB double door type, single pole and neutral 12 way 240Volts with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

Supply and fixing in replacement 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 63 Amp current carrying capacity in the MCB DB complete with connection testing and commissioning all as specified and directed by Enge-In-Charge.

S&F in replacement MCB Single Pole, 6 to 32 Amps 240 volts, 10KA breaking capacity, convenient to 'C' Curve complete all as specified and directed.

Supply and fixing in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make- Havells or Equivalent make in Bajaj/C&S

S& F in replacement LED tube light fittings of 20 wattage including rawl/plug ,making connection with and including 23/0 0076 flexible copper wire three core from connector to ceiling rose not more than 1.2 mtr fixed to wall firmly , complete all as specified and directed. Make: Philips/Syska /Bajaj/Havells

S & F in repairs LED panel decorative down light fitting/recess mounted square type white/ warm white 2X2 36W with high out put diffuser 220 V AC with driver holder and LED lamp including connecting up with flexible copper conductor cable of suitable size complete all as specified. .Make: Philips/Syska /Bajaj/Havells

S&F sub main wiring with two single core FRLSH PVC insulated unsheathed multistranded copper conductor of size 6 Sqmm nominal cross sectional area and one run of 6 sqmm nominal cross sectional area FRLSH PVC insulated unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25 mm dia 'medium grade' PVC concealed conduits and fittings, complete all as specified and directed. NOTE: One unit length shall measured as two run of main wire and one run of conduit & earth wire. Make: Havells/ Finolex / Polycab.

S & F wall Fans 230 volts single phase oscillating 400mm sweep, metal body with three speed controller switch all as specified and directed by Engr in Charge.Make - Usha Maxx Air/Havells/ Khaitan Magma

Supply and fix electric water heater, storage type plastic body with stailness steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.all as specified and DIrected by Engr-In-Charge. Make- Bajaj/Havells/Racold

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE.Five star rated with brushless direct current motor (BLDC) all as specified and Directed by Engr-In-Charge. Make-Usha Techno Air /Khaitan Magma/Bajaj Energos

jyoti parkash sharma (BID ID -3361305)

RAMAN CONSTRUCTION CO (BID ID -3360675)

vijay constrction co (BID ID -3360831)

paras ram pachiala (BID ID -3360159)

M/S Ashok Kumar Jaswal (BID ID -3360451)

RAJ MOHD (BID ID -3361327)

khajuria builders (BID ID -3361126)

VIRINDER SINGH (BID ID -3361070)

PARDEEP SHARMA (BID ID -3360141)