CERTAIN MISC REPAIR WORKS IN TECH UNITS AND RUNWAY AREA UNDER AGE B/R-II AT DINJAN

Amount

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges complete as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Pre-Painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, valley gutter & Eaves board fixed with self tapping screws complete all as specified and directed.

S & F plain, galvanised steel sheeting 0.63mm thick as in ridges hips, valley gutters, drip and straight flashings with grade of zinc coating 120gm/sqm fixed with screws complete all as specified and directed.

S & F Rolled mild steel work as in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. conforming to Fe-290-W (Gde-E-165) complete all as specified and directed.

M & L for Preparation of new zink (or galvanised) surfaces to receive painting, by coating with mordant solution including washing & cleaning and applying two coats of antisol roof paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M & L for Preparation of old treated steel surfaces of roof of any description over 10 cm girth or width and applying one coats of antisol roof paint complete all as specified and directed.

Dismantling timber boarding, any description, fixed in any position with nails complete all as specified and directed.

S & F 20 mm thick, second class hard wood boarding, clean sawn, planed one side with butt joints and fixed with nails in any situation as in eaves board, etc complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including cover fillets complete all as specified and directed.

Dismantling timber scantlings 40 Sq.cm and over in section (unframed work), in any position complete all as specified and directed.

M & L for second class hardwood, scantlings, clean sawn, in unframed work complete all as specified and directed.

S & F 2 mm thick, Fibre glass, reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

S & F aluminium Anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4mm thick,non asbestor E-board HSPC fixed with screw as per manufacturers instructions including two coats of white wash complete all as specified and directed.

Taking down chowkats or frame, n.exc 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames, exe 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutters of any description n. exc 1 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n. exc 2 Sqm each complete all as specified and directed.

M&L for 19mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and directed.

S & F well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints including termite treatment to timber liberally brushed at least twice with chemicals in oil or kerosene complete all as specified and as directed. (Note : Termite treatment should be done prior to fixing the chowkhat to wall)

M & L for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and directed.

S & F Mild steel small articles using flat iron of size 25x3mm thick such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290, Gde E-165 complete all as specified and as directed.

M & L for preparing surfaces of wood and wood based materials, steel and iron works, new or old of any description and girth treating ends of posts, back of chowkats etc, area tarred exc 0.1 Sqm but n.exc 0.5 Sqm each with tar or coal tar black paint complete all as specified and as directed.

S & F aluminium anodised sections, powder coated, minimum anodic coating of grade AC 15 for doors, windows, ventilators, door partition including fabrication of frame shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc. including all accessories such as glazings clips and rubber beadings for fixing glass panes in frame complete all as specified. Note : (i) Glass panes/wire net will be measured and paid seperately as supply only. (ii) The quoted rate shall be inclusive of cost of rubber beading however it will not be weighed and not paid seperately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate.

S&F 12mm thick prelaminated particle board, interior grade both sides with decorative choice lamination fixed to aluminium door/frame complete all as specified and directed

S&F 5.50mm thick sheet glass, ordinary quality in squares not exc 0.50 sqm each pane, cut to size required, grinding edges and/or fixed to aluminium door complete all as specified and directed.

S&F in repairs aluminium (extruded section body) door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified and directed.

M & L for 35mm thick 2nd class hard wood Plain, framed, panelled shutters (any number of panels), with panels of 12mm thick (Min) veneered particle board medium density with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed, Sizes/section of members of shutters shall be as specified in SSR Part I, Section -8, clause 8.24 (a).

S & F 35 mm thick, second class hardwood glazed and skeleton door shutters open rebated and prepared to receive glass, gauge, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass/gauze etc complete all as specified and directed in SSR Part I Section 8 clause 8.24 (a).

S & F 30 mm thick, second class hardwood glazed and skeleton shutters as in windows/ventilators open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, fitted with cut and mitered beads for securing glass/gauge etc and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded complete all as specified and directed in SSR Part I Section 8 clause 8.24 (b).

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

S & F 100 mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S & F 100 mm size, butt hinges, stainless steel fixed with cadmium coated steel screews complete all as specified and directed.

S & F 150 mm size, Aluminium handles, cast type, anodised complete all as specified and directed.

S & F 100 mm size, Aluminium handles, cast type, anodised complete all as specified and directed.

S & F 150 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F 100 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S & F 3 mm thick, sheet glass, ordinary quality and glazing with timber beads and back puittied in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing the rubbish off the premises complete all as specified and directed.

M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, as in floor surfaces such as skirting etc, including 15 mm thick screed bed in cement mortor (1:6), set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Glazed, ceramic, coloured tiles 6-7mm thick area of each tiles not less than 0.06 Sqm, on vertical surfaces such as skirting, dados etc, including 10 mm thick bedding in cement mortor (1:4), set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Machine cut granite slab 18 to 20mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including 15 mm thick screed bed in cement mortor (1:6) and rubbing, polishing complete all as specified and directed.

M & L for Machine cut marble slab flooring 18 to 20mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including 15 mm thick screed bed in cement mortor (1:6) and rubbing, polishing complete all as specified and directed.

M & L for Machine cut marble slab 8 to 20mm thick, as in skirting/dado laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including 10 mm thick screed bed in cement mortor (1:4) and rubbing, polishing complete all as specified and directed.

M & L for Vitrified, designed, coloured, tiles, 10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm, in floors, etc including 15 mm thick screed bed in cement mortor (1:6) and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Vitrified, designed, coloured, tiles, 10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm, in skirting, etc including 10 mm thick screed bed in cement mortor (1:4) and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for precast machine pressed interlocking paver block any shaped and size conforming to IS- 15658-2006, 50mm thick, M-30 grade concrete with grey cement and no pigment, set and jointed in dry sand including providing 60mm thick dry sand filling below paver blocks complete all as directed

Taking up or down 15mm bore, Steel tubing and connections complete all as specified and as directed.

Taking up or down 20mm bore, Steel tubing and connections complete all as specified and as directed.

Supply, laying, connection and testing, 15mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixtures complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

Supply, laying, connection and testing, 20mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixtures complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

S & F in repair 15 mm bore, bib taps, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm-125gms) complete all as specified and as directed.

S & F in repairs, 15 mm bore, Stop valves, cast copper alloy, chromium plated with long shank and cup, concealed type, screwed down high pressure, with capstan head, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repairs, 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and directed.

S & F in repairs, 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and directed.

S & F brass chromium plated health faucet with minimum 1.0 metre long braided flexible pipe and hook suitable for 15 mm bore iron pipes complete all as specified and as directed.

S & F in repairs, Vitreous China urinal, flat back of size 440X360X270mm, white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete complete as specified and directed. (Make: Parryware Cat No. C0501 or equivelant of make Hindware/Cera)

S & F in repairs, Vitreous China urinal, half stall type, white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete complete as specified and directed. (Make: Parryware Cat No. C0575 or equivelant of make Hindware/Cera)

Dismantling of rotational moulded polyethylene water tank of capacity exceeding 250 Litres but not exceeding 500 Ltrs complete all as specified and as directed.

Dismantling of rotational moulded polyethylene water tank of capacity exceeding 500 Litres but not exceeding 1000 Ltrs complete all as specified and as directed.

S & F in repair 500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top), hoisted and fixed in position including taking down old unserviceable one as specified in SSR Part I and directed.

S & F in repair1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top), hoisted and fixed in position including taking down old unserviceable one as specified in SSR Part I and directed.

S & F 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed

M & L for Preparation of old treated surfaces of walls of any description over 10 cm width or girth not otherwise described after complete removal of existing treatment and applying two coats of oil bound distemper over a coat of primer and providing wall care putty (min 1.00mm thick) complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness. (below or above ground level) complete all as specified and directed.

M & L for 100 mm thick, plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in floors laid in panels, finishing the surfaces even & smooth with using extra cement complete all as specified and directed.

M & L for Chequered cement concrete tiles of size 25cm x 25cm x 20mm thick, as in floors etc, including 15 mm thick screed bed in cement mortar 1:6 and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete (1:3:6), type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for 75mm thick Plain cement concrete (1:4:8), type D-2 (using 40 mm graded stone aggregate) as in sub-base of floor, etc complete all as specified and directed.

M & L for 40 mm thick, plain cement concrete (1:2:4), type B-1 (using 20 mm graded stone aggregate) as in floors laid in panels, finishing the surfaces fair and even without using extra cement to receive top layers complete all as specified and directed.

S & F 3 mm thick, 38mm wide glass dividing strips and inserted in position to conform to design complete all as specified and directed.

M & L in repair for precast cement concrete louvres and jallies 25 mm thick (measured solid) including all mouldings but excluding frame, set in cement mortar (1:4) complete all as specified and directed.

M & L for Painting lines, dashes, arrows, letters, etc on roads, pavement surfaces and the like n.exc 10cm wide with /runway marking Hi-Gloss premium enamel fluorescent paint, white or golden yellow colour, 2.5mm thick layer of marking and 250gm/sqm glass beads consumed in per sqm ratio complete all as specified and directed.

M & L for Painting lines, dashes, arrows, letters, etc on roads, pavement surfaces and the like n.exc 10cm wide with road marking paint white or golden yellow two coats for the desired result complete all as specified and directed.

S & F supper flash strip UV resistant self-adhesive flashing bituminous tape for water proofing bonding, sealing for transperent sheets in hanger roof complete all as specified and as directed.

S & F in repairs, galvanised mild steel wire cloth 0.56 mm nominal dia of wire average width of aperture 1.18mm and fixed with tinned tacks or Stainless steel wire staples timber beads complete all as specified and directed.

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and flushing pipe, anti syphonic pipe with PVC seat and cover complete but excluding flushing cistern & flush pipe including making good damaged/disturbed surfaces complete all as specified and directed.

S & F in repairs, vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and directed.

S & F in repairs, vitreous China semi pedestal pattern (Anglo Indian type) white water closet pan including connection to outgoing drain and flushing pipe, anti syphonic pipe with PVC seat and cover (white), complete but excluding flushing cistern & flush pipe including making good damaged/disturbed surfaces complete all as specified and directed.

S & F 110 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints laid in floor or fixed to wall using MS holder bats, etc complete all as specified and directed.

S & F 110 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints laid in trenches complete all as specified and directed.

S & F 75 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints fixed to wall using MS holder bats, etc complete all as specified and directed.

S & F 75mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints laid in trenches or in floor, etc complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends with oval acess door of any radius complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends of any radius complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) bends of any radius complete all as specified and directed.

S & F 15 mm bore, pillar taps, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F in repairs, vitreous China wash basin, size 550 x 400mm, white, flat back, with PVC waste pipe, CP waste coupling, chain, plug and porcelean stopper & backets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and directed. (Make : Parryware, Cat No C0406 or equivelant of make as specified in list of manufacturer)

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M & L for brick work using locally available first class bricks sub class 'B' bricks (old size brick), straight or curved on plan exc 6m mean radius, built in cement mortar 1:4 half brick thick wall complete all as specified and directed.

M&L for Brick work using locally available first class bricks sub class 'B' bricks (old size brick), straight or curved on plan exc 6 m mean radius, built in cement mortar (1:6) complete all as specified and directed.

M & L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in two layer (10mm and 5mm thick) on fair faces of brick work or concrete surfaces in cement mortar (1:4), mixed with integral water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M & L for rendering 5 mm thick in cement mortor 1:3 on concrete surfaces as in ceilings (sunshed, chajja, pins etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proof compound for external plaster complete all as directed. Make - Dr Fixit of Pedilite or equivalent as approved by GE.

M & L for preparation of new plastered surfaces of walls and applying two coats of white wash complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M & L for 4mm thick epoxy coating floor high density, heavy duty in hanger floor including taking out existing epoxy coating, cleaning , preparation the surfaces to lay new epoxy floors all as directed.

M & L for preparation of old surfaces including brooming down or steel wire brushing, csrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots on walls and applying two coats of white wash including cleaning the floors/joinery surfaces, glass panes etc complete all as specified and directed.

M & L for preparing plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of primer over a coat of wall care putty (minimum 1mm thick) complete all as specified and directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for Preparation of old painted wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Cutting grass, small trees, bushes manually by deploying at least 02 numbers mozdoor from 9.00 AM to 05.00 PM (half an hour lunch break at mid day) both sides of runway and removing the same to a distance not exc 50m and depositing as directed. Note :- Manpower shall be deployed every day except Sunday/Holiday. However Department shall have reserved the right to stop the work at any time even in working day due to security reason and no extra claim on this shall be entertained.

Cutting grass, small trees, bushes by mechanically operated 50mm to 100mm slasher from 9.00 AM to 05.00 PM (half an hour lunch break at mid day) both sides of concrete pavement edges and removing the same to a distance not exc 50m and depositing as directed. Note :- Contractor will have to arrange at his own the mechanical slasher ie one set of tractor and jungle jeem including POL driver. Mechanical slasher shall be deployed every day except Sunday/Holiday. However Department shall have reserved the right to stop the work at any time even in working day due to security reason and no extra claim on this shall be entertained.

Taking down XLPE insulated, armoured heavy duty electric cavble, screened PVC bedded, with aluminium conductor 1100 V grade, from trenches/along poles, ducts or through sleeve complete of size 6sqmm to 25sqmm 2/3.5/4 core all as specified. Note : Earth work, sand cushioning and bricks will be measured and paid separately under relevant items.

All as per items No 113 above but of size 50 sqmm to 120 sqmm complete all specified and as directed.

All as per items No 113 above but of size 150 sqmm to 240 sqmm complete all as specified and as directed.

Relaying of XLPE insulated, armoured heavy duty electric cable, screened PVC bedded, with aluminium conductor 1100 V grade, from trenches/along poles, ducts or through sleeve after removing the damaged / out cable complete of size 6sqmm to 25 sqmm 2/3.5/4 core retrieved from item No 113 above all as specified and as directed.

Relaying of XLPE insulated, armoured heavy duty electric cable, screened PVC bedded, with aluminium conductor 1100 V grade, from trenches/along poles, ducts or through sleeve after removing the damaged / out cable complete of size 50 sqmm to 120 sqmm 3.5 core retrieved from item No 114 above all as specified and as directed.

Relaying of XLPE insulated, armoured heavy duty electric cable, screened PVC bedded, with aluminium conductor 1100 V grade, from trenches/along poles, ducts or through sleeve after removing the damaged / out cable complete of size 150 sqmm to 240 sqmm 3.5 core retrieved from item No 115 above all as specified and as directed.

Supply, laying and testing XLPE insulated, armoured heavy duty electric cable, screened PVC bedded, with aluminium conductor 1100 V grade, laid in trenches/along poles, ducts or through sleeve including taking out existing unserviceable cable of size 50 sqmm 3.5 core complete all as specified. Note : Earth work, sand cushioning and bricks will be measured and paid separately under relevant items. Make : Havells / Polycab/cci/nicco/Gloster.

All as per items No 119 above but 35 sqmm 3.5 core complete all as specified and as directed.

All as per items No 119 above but 25 sqmm 4 core complete all as specified and as directed.

All as per items No 119 above but 10 sqmm 2 core complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5M deep for foundation/cable trench, not exceeding 10 sqmm on plan and getting out in soft/loose soil all as specified and as directed.

Returning filling including spreading, levelling and well ramming in layers not exceeding 25 cm thick in soil complete all as specified and as directed.

Removal of surplus soil to a distance not exceeding 50 M and depositing where directed at a level not exceeding 1.5M above the starting point complete all as specified and as directed.

Supply and providing sand cushioning with dry clean sand 15 cm below cable and 8 cm above the cable complete all as specified and as directed. Note: Punned thickness shall be measured for the purpose of payments.

Supply and laying flyash building bricks laid in trenches for LT cable protection with length of brick perpendicular to lengthof cable complete all as specified and as directed.

Supply and laying 80mm dia GI pipe, medium grade with all fittings laid in trenches, road crossing and fixed to walls, on poles etc complete all as specified and as directed. Make : Tata/Jindal/Zenith

Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with jointing material heat Shrink type and accessories suitable for 3 1/2 / 4 core XLPE, armoured, AI conductor cable of size 25 to 50 sqmm, Indoor/Outdoor type complete all as specified and as directed.

All as per items No 129 above but of size 70 to 240 sqmm complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate as in filling and mass concrete after clearing the broken/damaged existing PCC complete all as specified and as directed.

Supply, fabricate, erect, test and commission Outdoor LT Feeder pillar box totally enclosed weather and vermin proof, suitable verntilated, 440 Volts, 50 HZ, AC supply, factory made out of 2 mm thick CRCA sheet steel for load bearing protectionof enclosure IP-54 complete hinged door with pretreatment and powder coating of approved colour including suitable angle iron/flat iron frame work supports, excavation and earth work, PCC foundation etc, cubical type as required with and including he sollowing, supplied fitted and connected internally complete (a) 04 Nos aluminium bus bar of unequal size of aluminium conductor with PVC coloured heat srinkable type sleeves continous phas rating 300 Amps and neutral rating 200 Amps mounted on non cracting resin type insulators complete all as specified and as directed.

Taking down the existing street light fittings of SV/CFL from the street lights poles of any make and capacity carefully and supply and fixing new LED street light fitting of capacity 90W, with pressure die cast housing, toughned glass and individual LEDs with secondary optics and IP 66 protection, including withnecessary brackets/pipes/clamps & nuts & bolts for holding the street light fitting and twin core aluminum cable of 2.5 sqmm as required inexisting location complete all as specified and as directed. Make : C&S Cat No LTESS90WLED or equivalent in CG/Philips/HPL/Everday (Warrenty on Driver, LEDs and PCB for 5 years to be submitted by the contractor)

M/s GANDHESWAR PHUKAN

STANDARD ELECTRIC WINDERS

AFTAB ENTERPRISES

Kaushik Enterprises

M/S CHANDAN ENTERPRISE

Construction House