REPAIR/MAINT OF ALUMINIUM JOINERY, FALSE CEILING, ROOF SHEET, SANITARY AND PLUMBING WORK, INTERLOCKING PATH, HARDSTANDING OTHER MISC B/R WORKS AND PERIODICAL SERVICES TO ZONE A AT COMD HOSP (CC) IN THE AREA OF AGE E/M (HOSP) UNDER GE E/M LUCKNOW

Amount

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and pre cast concrete articles complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level), complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L fly ash bricks, old size as per IS 1489 (Part I)-2002 buit in CM 1:6 straight or curved on plan exc. 6 M mean radius complete all as specified and directed.

M&L TMT 10mm dia and over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming Fe- 500, complete all as specified and directed.

PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in coping, chajja, facia and the like including weathering, slightly rounded or chamfered angles with & incl necessary use and waste of form work for fair faces of concrete, complete all as specified and directed.

Supply only integral water proofing compound powder ISI marked, complete all as specified and directed.

Mild steel work Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 as in small articles like angle iron framing work for manhole, rungs/steps in man hole, complete all as specified and directed.

Treating small articles of steel like MS rungs etc with coal tar black paint icl preparation of surface, area tarred not exc 0.1 sqm, complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and directed.

M & L for Super heavy series PVC Wall panelling/Lining consisting of 5mm thick Plain/wood colour PVC sheet as approved inclusive of solvent cement and fixing at site on PVC frame including complete fixing arrangments on wall complete all as per manufactures specifications, complete all as specified and directed.

M & L for PVC Wall Stickers Wallpaper, waterproof and heat resistence , Textured Embossed Home Interior Decoration, Self Adhesive, with and including complete fixing arrangments on wall all as per manufactures specifications and instructions, complete all as specified and directed.

Providing and fixing of E-board 'Everest' make 600x600x4mm thick white prelaminated seif embosed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24 mm wide T-section/Angle section, complete all as specified and directed.

M&L Suspended ceiling, comprising 12.5 mm thick reinforced gypsum plaster boards Conforming to IS-2095 , GI perimeter channels, intermdiate channels, etc. including finishing the exposed surfaces with Oil bound distemper two coats over and including 2 mm thick Birla wall care putty complete all as specified and directed.

Taking down chowkhats or frame (wooden/aluminium) n. exc. 1.5 Sqm each with shutters (with out taking off shutters from the frame) and taken as credit complete all as specified and directed.

Taking down chowkhats or frames (wooden/aluminium) with shutters without taking off shutter from the frames exc. 1.5 but n. exc 4 sqm each complete all as specified and directed.

Taking down shutters of any description n exc 1 sq.m each complete all as specified and directed.

Taking down shutters of any description exc 1 sq.m and n exc 2 sq.m each complete all as specified and directed.

PVC door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

S &F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm with stuck inside with, complete all as specified and directed.

S&F 250 mm aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 100 mm length of bolt complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

S & F in repair for 150 mm floor door stopper of aluminium alloy body and tonge,anodised with hard drawn steel spring, complete all as specified and directed.

Hacking out old broken glass, any thickness, size, quality, or description, from frame nexc 1.5 Sqm each pane, complete all as specified and directed.

S&F for 3.0 mm thick sheet glass ordinary quality and glazing with oil putty nexc 0.5 Sqm each pane, complete all as specified and directed.

S&F for 3.0 mm thick figured glass ordinary quality and glazing with oil putty n.exc 0.5 Sqm each pane, complete all as specified and directed.

S&f for 4.8 mm thick sheet glass odinary qulity and glazing with neosprene beading n.exc 0.5 Sqm in each pane, complete all as specified and directed.

S&F in repairs Chromium plated fancy long body Bib taps with cup, cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair cast iron floor trap with chromium plated grating including jointing to waste pipe wih cement mortar (75 mm bore of pipe), complete all as specified and directed.

S&F in repairs Brass chromium plated shower rose without swivel joints , any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs Chromium plated ,Concealed stop cock Reduced body ISI Marked, , cast copper alloy, screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed.

S&F in repair CP Angle stop cock ( one way) long thread with wall flange , fancy type screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed.

S&F in repairs Pillar taps, fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs PTMT( Polytetra Methyllene Terephthalate )Bib taps suitable for 15 mm bore pipe standard of PTMT any colour screwed, for iron pipe and fixed ( Minimum weight 15 mm-90 gms complete all as specified and directed.

S&F in repairs CP Angle stop cock( two way) long thread with wall flange , screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed.

S&F in repairs CP mild steel gratings suitable for 75/100 mm dia NT/ FT complete all as specified and directed.

S&F in repairs Chromium plated Brass Tubular towel rod, of 24" (60 cm long) complete all as specified and directed.

S&F in repair vitreous China wash down water closet pan (padestal pattern Water Closet ) , ( excluding fixing bolts, flushing cistern and flush pipe) , including connection to drain ( or outgoing pipe) and to flushing pipe, etc., complete all as specified and directed.

S&F in repairs VC WHITE Squatting pan ,'Orissa' pattern size 580x440mm with integral footrests water closet) with 'P' or 'S' trap front or back inlet complete including lime concrete for bedding, connection to drain pipe and to flushing pipe , anti syphon, complete all as specified and directed.

S&F in repairs Low level flushing cistern, moulded from virgin poly propylene complete all as specified and directed.

Supply and fixing in repairs Plastic water closet seat, white, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F Vitreous China bowl urinal flat back, size of 465x355x265 mm White (minimum), with grating and union for discharge pipe ( excluding flushing cistern, flush pipe , and waste pipe) , fixed in repairs including connections to flushing pipe and outgoing, complete all as specified and directed.

S&F in repair vitreous china wash basin (WHB) , white , flat back , size 550mmx400mm including brackets, waste fittings , brass Chromium plated for glazed basins etc. with long screw shanks and fly nuts , flange end embedded in red lead cement , including cutting, complete all as specified and directed.

S&F 32mm bore flexible pipe of PVC fixed to WHB/ urinals as waste pipe ( not less than 600mm) including PVC coupling complete all as specified and directed.

M&L in repairs 32 mm waste fittings , brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repairs 32 mm bore flexible pipe of PVC fixed to WHB/ urinals as waste pipe ( not less than 600mm) including PVC coupling complete all as specified and directed.

S&F in repair Gun metal , globe or gate valves, with iron wheel head, screwed both ends for 20 mm bore dia. iron pipe and fixed complete all as specified and directed.

S&F Gun metal, in repair globe or gate valves, with iron wheel head, screwed both ends for 15 mm bore dia. iron pipe and fixed complete all as specified and directed.

S & F Neosprene rubber beading including taking down old rubber beading as in aluminium window and door shutter, complete all as specified and directed.

S&f for 12 mm thick toughned glass odinary qulity and glazing with neosprene beading, SS clip or cleats of any size any postition, complete all as specified and directed.

Repairing of existing aluminium door single/double leaf including oiling and greasing of floor springs,replecing of rubber beading if required,replacement of hinges,handle,towerbolt of any size any type present at site on required basis,also including replacement of any membre of aluminium section i.e frame & shutters membre and 3-5 mm glass and making the door and shutter serviceable complete all as specified and directed. (Note:-Floor door springs where renewed shall be measured and paid separately under appropriate

Repairing of existing toughend glass door single leaf including oiling and greasing of floor springs,replacement of hinges,handle,lock of any size any type present at site on required basis,also including replacement of any membre of aluminium section i.e frame & shutters membre and 12 mm glass and making the door and shutter serviceable complete all as specified and directed. (Note:-Floor door springs where renewed shall not be measured & paid seperately it includes the rate of floor spring also)

Supply & fixing in repair Double action floor spring hydraulically regu-lated made up of minimum 1.25 mm thick alu-minium alloy sheet foun-dation box,main body with stainless steel cover, governing pivot made of mild steel heavy duty fixed, complete all as specified and directed.

S&F in repairs Aluminium body ( extruded section ) body Door closer hydraulically regulated, designation No. 2 , universal type , suitable for door shutters 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed, complete all as specified and directed.

S&F in repair for 100 mm mild steel 4 lever mortice lock vertical type of size of brass body, complete all as specified and directed.

S&F Anodised aluminium frame for doors, windows, ventilators, partition section with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief, complete all as specified and directed.

S &F in repair aluminium partition with pre-laminated particle board at bottom panel and 4.8mm thick glass on top panel incl glazing clip and neosprene rubber beading complete all as specified and directed.

S &F in repair aluminium partition with 3mm thick aluminium composite panel at bottom panel and 4.8 mm thick glass on top panel incl glazing clip and neosprene rubber beading complete all as specified and directed.

S &F 3mm thick aluminium composite panel with aluminium frame and shtter in door incl glazing clip and neosprene rubber beading complete all as specified and directed.

S &F 3mm thick aluminium composite panel with glazing clip and neosprene rubber beading complete all as specified and directed.

S&F Aluminium grill not less than 3.13 Kg per sqm fixed with frame in windows/ventilator complete all as specified and directed.

S&F Anodised Aluminium alloy sections sliding windows shutters with frames comprising Series -C (20mm), 2 track sliding shutters duly fitted with neoprene beading, glazing clips,locking device, heat absorbing glass 4.8 mm nominal thicknes complete all as specified and directed.

S&F Anodised Aluminium alloy sections sliding windows shutters with frames comprising Series -C (20mm), 3 track sliding shutters duly fitted with neoprene beading, glazing clips,locking device, heat absorbing glass 4.8 mm nominal thicknes in 2 shutters and 0.46mm dia SS wiremesh in one shutter complete all as specified and directed.

S&F aluminium sections ( conforming to IS) door with frame of size 100mmx 44.45mm wide fabricated with 2mm thick section , double leaf shutter with 44.45mm wide fabricated with 2mm thick section having vertical and top rail 83.50mm, bottom rail and middle rail 115mm and including necessary jointing cleats, screws, neosprene rubber beading, PVC packing, tinted glass panes 4.8 mm nominal thickness complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.23(b) complete all as specified and directed.

S&F 100mm size butt hinges medium weight (ISI Marked), rolled mild steel complete all as specified and directed.

S&F 75mm size butt hinges medium weight (ISI Marked), rolled mild steel complete all as specified and directed.

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 20mm thick in cement mortor 1:4, complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surfaces 350 x 250 x 7 mm / 450 x 350 x 7 mm [thick] set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over and including 10mm thick screed in CM 1:3, complete all as specified and directed.

S&F powder coated anodised Aluminium alloy sections sliding windows shutters with frames comprising Series -C (20mm), 3 track sliding shutters duly fitted with neoprene beading, glazing clips,locking device, heat absorbing glass 4.8 mm nominal thicknes in 2 shutters and 0.46mm dia SS wiremesh in one shutter complete all as specified and directed.

S & F in repairs powder coated aluminium grill 3.13 Kg per Sqm (min) with grill frame of 0.297 Kg per meter (min). (Design as approved by Engr-in-charge), complete all as specified and directed.

Excavating in post holes each not exc. 0.5 cum getting out in soft / loose soil, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc. 25 cm, watering and removing surplus soil to a distance not exc. 50 m and depositing where, complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 as in foundation and mass concrete using 40 mm graded stone, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

M&L for preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling of roof sheet (any descriptions) including ridges in roof covering complete all as specified and directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for providing cement concrete type B-1, 1:2:4 (20 mm graded aggregate ) as in roof kerbs /padding or similar work or mud stops rounded or chamferred on edges, complete all as specified and directed.

M&L 6-10mm thick wall tiles in repairs Duracrete manufactured by M/S Intex Designer Tiles Pvt Ltd. or equivalent of other specified make ) as invertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 10mm thick screed in CM 1:3, complete all as specified and directed.

Taking down cement plaster on brick wall, racking out joints hacking for key scrubbing down with water complete all as specified and directed.

M & L for acrylic polymer-modified cementitious high performance coating (two component) with high solid content and can be used for both side waterproofing due to its excellent bonding, good waterproofing and unmatched resistance to hydrostatic pressure which resist up to 5 bars of positive hydrostatic pressure and form highly elastic film which provides elengation up to 100 as per manufactures instructions complete all as specified and directed. (Product of Asian paint or equivalent) (Note:- Work to be carried out by the authorised applicators of manufactures only)

15mm thick rendering on brick work or concrete surfaces in CM 1:6 finished fair & even without extra cement, cement mortar mixed with WPC @ 3% of weight of cement, complete all as specified and directed. (Note: WPC measured & paid for separately)

M&L for rendering 10 mm thick on brick work/ concrete surfaces in cement mortar 1:6 on fair faces finished fair & even, complete all as specified and directed.

M&L rendering 5 mm thick on concrete surfaces in ceiling , in cement and sand mortar 1:3 complete all as specified and directed.

M&L for preparing surfaces, plastered or unplastered new surfaces of ceiling and applying three coats white wash complete all as specified and directed.

Preparation of newly plastered surfaces and applying two coat of oil bound disemper over one coat of oil base primer all as specified on walls surface including a coat of 3mm wall care putty, complete all as specified and directed. Note :- Distempering shall be carried out through roller/air less spray machine (mechanically means)

M&L applying two coats of Apex (Weather coat) over newly plastered surface including preparation of wall surface complete all as specified and directed. Note :- Painting/Primer shall be carried out through roller/air less spray machine (mechanically means)

Preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L applying one coats of plastic emulsion paint interior quality any shade over old painted surface including preparation of wall surface complete all as specified and directed. Note :- Painting/Primer shall be carried out through roller/air less spray machine (mechanically means)

Preparation of old plastered or unplastered surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

All as per item No. 98 above but on ceiling.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of cement base paint of any tint/shade complete all as specified and directed.

All as per item No 100 above but two coats

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of distemper oil emulsion of any tint/shade complete all as specified and directed. Note :- Painting/Primer shall be carried out through roller/air less spray machine (mechanically means)

All as per item No.102 above but two coats

All as per item No 102 above but on ceiling.

Preparation of old painted surfaces of steel of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed.

Complete removal of existing treatment of walls and applying two coats of distemper oil emulsion over a coat of Birla or JK white wall putty average thickness 2mm on old plastered surfaces including prepration complete all as specified and directed.

M & L preparation of old brick, stone, concrete, AC or decorated plastered surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed

Complete removal of existing treatment on wall/roof projections including facia, cornics etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc and M&L applying one coats of exterior emulsion paint over and including 2mm thick Birla wall care putty complete all as specified and directed. Note :- Painting/Primer shall be carried out through roller/air less spray machine (mechanically means)

M&L for fly ash bricks, old size as per IS 1489 (Part I)-2002 straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4, complete all as specified and directed.

M & L for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates (Grade Fe- 290 (Gde E- 165) complete all as specified and directed.

M&L for filling joints between two panels with mix of 85/25 bitumen and sand in 1:3, complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as plinth protection/path and the like all complete all as specified and directed.

M&L for cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in coping,padding and bed block, wall through and the like including weathering slightly rounded or chamfered angles and throating including necessary form work, complete all as specified and directed.

M&L 18-20mm thick machine cut Kota stone slab flooring with marble stone strips/ slab/ tiles as per design approved, over and including cement screed bed 15mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, complete all as specified and directed. (Note : Screed bed will not be measured and paid separately)

M&L 18-20mm thick machine cut Kota stone slab as in skirting /riser over cement screed bed 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, complete all as specified and directed. (Note : Screed bed will not be measured and paid separately)

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for non skid ceramic tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 15mm thick screed in CM 1:6, complete all as specified and directed. (Note : Screed bed will not be measured and paid separately)

M&L Vitrified ceramic tiles 10mm thick (square/ractangular) Coloured polished tiles, area of each tile n.exc 0.38 sq m in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement and pigment to match over 15 mm thick screeding in CM 1:6, complete all as specified and directed. (Note : Screed bed will not be measured and paid separately)

Anti-Microbial Protection: These product hygiene coatings start the bio cidal action as soon as the microorganism land on the surface, and prevents the growth of mould, bacteria and yeasts for at least 5 years. This Hygiene coating are independently tested by leading universities to demonstrate resistance. Note : (Anti-Microbial Protection: Filling of all Joints and cavities and Sanded Flush to provide a joint less finish and then sprayed with a water based liquid plastic aseptic and self sterilizing wall coating system to a d.f.t. of 300 microns with primer. These hygiene coatings should start the biocidal action as soon as the microorganism land on the surface, and prevent the growth of mould, bacteria and yeasts for at least 5 years. Make SIKKA ( Formally Liquid Plastic) (Note:- The work will be carried out in OT rooms in a peace-meal or very restricted permissible condition, quoted rates deemed to included for wastages of labour and material components accordingly)

Conductive Flooring: 2mm thick Conductive flooring with carbon backing total thickness 2.00mm, total weight 3.000 g/m2 polyurethane reinforced ,scratch resistant, fire resistant, chemical resistant , slip resistant, anti fungi & bacterial growth , dimensional stability 0.40%, static electrical charger < 2Kv , impact sound reduction approx +4bd, electrical resistant. Installation : The flooring would be installed on a smooth, clean sub floor which should be free from any undulation .A copper strip/mesh should be layer under the tiles, with one earthing point for every 150 sft of area and good quality water based adhesive for fixing as per as manufacturers recommendation. Thermal Welding : The joints must be welds by the heat fusion process to get a seamless floor. The joints in the flooring should be sealed by using a PVC welding bar of matching color to be supplied by the manufacturer, using a hot air gun for fusion of welding bar with flooring. The same application to be done for wall skirting up to max 150mm and coving to be provided using appropriate material and method. Make – Gerfloor/ Tarquet , France or equivalent (Note:- The work will be carried out in OT rooms in a peace-meal or very restricted permissible condition, quoted rates deemed to included for wastages of labour and material components accordingly)

Taking up or down steel tubing and connections , including cleaning for re-fixing or removal of store, 15 mm bore complete all as specified and directed.

Taking up or down steel tubing and connections , including cleaning for re-fixing or removal of store, 20 mm bore complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling , floors, etc.)15 mm nominal bore complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling , floors, etc.)20 mm nominal bore complete all as specified and directed.

M&L 15 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L 20 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Taking down existing PVC water tank capacity exc 250 & n.exc 500 ltr and S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I. capacity of tank 500 litres complete all as specified and directed.

Taking down existing PVC water tank capacity exc 500 & n.exc 1000 ltr and S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I. capacity of tank 1000 litres complete all as specified and directed.

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete all as specified and directed.

Temporarily blocking of inlet of septic tanks/manhole with suitable wooden plugs/gunny bags and pumping/bailing out effluent and taking out/removing the accumulated sludge soil sewage/any other foreign/foul materials etc (solid/semisolid) from the septic tanks/manholes. complete and cleaning the septic tank/manholes with water by mechanically including taking out the blocking arrangements of inlet and making the system functional complete all as specified and directed. NOTE: (i) Depth of manhole/SOAK WELL/SEPTIC TANK exc 0.5 to 1.5M from below GL (ii) Size of tank upto water level shall be measured

Temporarily blocking of inlet of septic tanks/manhole with suitable wooden plugs/gunny bags and pumping/bailing out effluent and taking out/removing the accumulated sludge soil sewage/any other foreign/foul materials etc (solid/semisolid) from the septic tanks/manholes. complete and cleaning the septic tank/manholes with water by mechanically including taking out the blocking arrangements of inlet and making the system functional complete all as specified and directed. NOTE: (i) Depth of manhole/SOAK WELL/SEPTIC TANK exc 1.50M to 4.50M from below GL (ii) Size of tank upto water level shall be measured

Temporarily blocking of sewage line with suitable wooden plugs/gunny bags and cleaning the same by rod-ding and removing the sludge alongwith brick bats/stones/broken bottles/any other foreign materials etc complete and cleaning the sewage line with water by mechanilly as directed by EIC, and taking out the blocking arrangements of inlet and making the system functional for 150 mm bore size of pipe lines, complete all as specified and directed.

All as per item No 132 above but 200 mm bore

All as per item No 132 above but 250 mm bore

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed concrete to SGSW pipes of 250 mm bore dia incl packing under & haunching against the sides of pipes after they are laid & tested, complete all as specified and directed.

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed to SGSW pipes of 200 mm bore dia incl packing under & haunching against the sides of pipes after they are laid & tested, complete all as specified and directed.

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed to SGSW pipes of 150 mm bore dia incl packing under & haunching against the sides of pipes after they are laid & tested, complete all as specified and directed.

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed to SGSW pipes of 250 mm bore dia incl packing under & completely surounding pipes with conrete after they are laid and tested, complete all as specified and directed.

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed to SGSW pipes of 200 mm bore dia incl packing under & & completely surounding pipes with conrete after they are laid and tested, complete all as specified and directed.

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed to SGSW pipes of 150 mm bore dia incl packing under & & completely surounding pipes with conrete after they are laid and tested, complete all as specified and directed.

Salt-glazed stone ware drain (SGSW) pipe grade 'A' 150 mm bore dia laid in trenches & jointed in CM 1:1 including taking down complete all as specified and directed.

Salt-glazed stone ware drain (SGSW) pipe grade 'A' 200 mm bore dia laid in trenches & jointed in CM 1:1 including taking down complete all as specified and directed.

Salt-glazed stone ware drain (SGSW) pipe grade 'A' 250 mm bore dia laid in trenches & jointed in CM 1:1 including taking down complete all as specified and directed.

Dismantling fencing wire,any type, complete all as specified and directed.

Mild steel screw bolts (machine made) of 10 mm dia of sank with hexagonal or squre head at one end & screw the other or screwed both end (as directed) each screwed end to be fitted with washer and one hexagonal or square nut n exc 5 cm long, complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire, complete all as specified and directed.

Supply only chain link MS galvanised fencing of any shape and size complete all as specified and directed.

S & F in repair for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and directed. (each line wire to be measured)

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for exterior grade outdoor coloured floor tiles (heavy duty) of tactileseries of size 300x300x10mm of Make Johnson endura or equivalent make bedded over and including 20mm thick screed bed in CM 1:6 and jointed in cement mortar to match the colour of floor complete all as specified and directed.

M&L Chequered cement concrete coloured tiles 30 cmx30cmx20 mm thick with coloured cement and pigment , set, jointed and pointed in neat cement slurry over 20mm thick screed bed in CM 1:4 as in floors complete all as specified and directed. (Note : Screed bed will not be measured and paid separately)

M & L for 75mm thick plain cement concrete type D- 2, 1:4:8 (40mm graded aggregate), complete all as specified and directed.

M & L for Hardcore of gauge n exc. 63mm, of broken bricks, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface, complete all as specified and directed.

M/s Bipin Construction

AJANTA ENGINEERS

M/S SWATI CONSTRUCTION

M K Engineers and Contractors

M/S Reliance Construction